Vehicle report

2005 NISSAN MAXIMA

Service bulletins

88 bulletins

Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.

NTB09-131C

Service Bulletin/Repair Instructions

CERTIFICATION LABEL AND VIN PLATE REPLACEMENT SERVICE INFORMATION Because of collision damage or other vehicle repair, a replacement “Certification Label” or “VIN Plate/Label” may be needed. HINT: Certification Label = FMVSS (Federal Motor Vehicle Safety Standards) label. These items may be available from Nissan by request if certain criteria are met. This bulletin lists the criteria and provides an application form for such replacements. · The “VIN Plate/Label” (metal plate or vinyl label) is attached to the instrument panel or body on the driver side at the base of the windshield (see Figure 1). · The “Certification Label” (vinyl adhesive label) is located on the lower area of the driver side B-Pillar (see Figure 1).

NTB10-066C

Service Bulletin/Repair Instructions

CAN COMMUNICATION CODES – DIAGNOSTIC TIPS AND GUIDELINES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB13-027D

Service Bulletin/Repair Instructions

CAN COMMUNICATION – NETWORK DIAGNOSTIC FLOW CHART This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB13-107G

Service Bulletin/Repair Instructions

VEHICLE KEY NOT DETECTED / AUTHENTICATED, ENGINE WILL NOT START This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB09-081K

Service Bulletin/Repair Instructions

WINDSHIELD CRACKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB13-028I

Service Bulletin/Repair Instructions

REMOVING FOREIGN MATERIAL FROM THE WINDOW GLASS This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB17-019H

Service Bulletin/Repair Instructions

WINDOW GLASS WARRANTY INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB22-095A

Service Bulletin/Repair Instructions

VOLUNTARY SERVICE CAMPAIGN 2002-2006 ALTIMA AND 2004-2008 MAXIMA; FLOOR PAN Voluntary Service Campaign ID # PC926 is no longer active.  Repair orders opened after this bulletin’s published date are no longer eligible for reimbursement under Campaign ID # PC926.  Discard all previous versions of NTB22-095.

PC926 04-08 Maxi

Service Bulletin/Repair Instructions

Expiration Notification - Maxima/Altima Floor Pan ***** Dealer Announcement ***** On October 28, 2022, in connection with the court-approved settlement of class action litigation filed in Missouri, Nissan launched a Voluntary Service Campaign (VSC) on 36,858 specific model year 2002-2006 Nissan Altima and 2004-2008 Nissan Maxima vehicles to inspect, and if necessary, repair for front floor pan corrosion. Per the terms of the settlement, the VSC expired on November 1, 2023. This Voluntary Service Campaign and customer reimbursement for these repairs will no longer be available after November 1, 2023. ***** What Dealers Should Do ***** 1. Service Comm will deactivate PC926 on any unrepaired VINs on November 1, 2023. No further dealer action is required.

NTB08-097L

Service Bulletin/Repair Instructions

DIAGNOSIS OF VEHICLE PULL (DRIFT) AND/OR STEERING WHEEL OFF-CENTER This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB23-049

Service Bulletin/Repair Instructions

12 VOLT BATTERY TESTING FOR IN-SERVICE VEHICLES SERVICE INFORMATION The following Service Information lists NNA procedural recommendations for establishing good connections while performing 12V battery testing. These recommendations are expected to promote uniformity during the connection process, therefore reducing the number of incorrect “Test with DCA” and “Replace” results. HINT: If 12 volt batteries are allowed to discharge for a prolonged period of time, battery life may be drastically reduced. This condition may lead to premature battery replacement and customer dissatisfaction. IMPORTANT:  CPX-900 is now an accepted testing tool to use along with or in place of the DSS-5000  CPX-900 operating instructions are found at: https://nissancpx900.midtronics.com/  DSS-5000 operating instructions are found at: https://nissandss5000.midtronics.com/  DCA-8000 is now a required testing tool to be used for all warranty replacement decisions. The DCA-8000 is also a more efficient charger than previously available, and will charge any available 12 volt lead acid battery safely and accurately as long as all precautions and inputs are made correctly. The DCA-8000 operating instructions are found at: https://nissandca8000.midtronics.com/

NTB23-053

Service Bulletin/Repair Instructions

SILICONE-BASED LUBRICANT OR GREASE CAN DAMAGE ELECTRICAL COMPONENTS SERVICE INFORMATION Do not apply Silicone-based lubricants or grease to, or around, any interior electrical components. To avoid the risk of death or severe personal injury, do not directly spray Silicone-based lubricant or grease, or inadvertently overspray Silicone-based lubricant or grease onto any interior electrical components. These types of lubricants can be detrimental to the proper operation of electrical components.

NTB13-107F

Service Bulletin/Repair Instructions

VEHICLE KEY NOT DETECTED / AUTHENTICATED, ENGINE WILL NOT START This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB16-003C

Service Bulletin/Repair Instructions

INTELLIGENT KEY REPLACEMENT OR SWAPPING BETWEEN VEHICLES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.

NTB10-145B

Service Bulletin/Repair Instructions

ABS/VDC CAN DIAGNOSIS INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB09-081J

Service Bulletin/Repair Instructions

WINDSHIELD CRACKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB13-028H

Service Bulletin/Repair Instructions

REMOVING FOREIGN MATERIAL FROM THE WINDOW GLASS This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB08-097K

Service Bulletin/Repair Instructions

DIAGNOSIS OF VEHICLE PULL (DRIFT) AND/OR STEERING WHEEL OFF-CENTER This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB10-126C

Service Bulletin/Repair Instructions

WHEEL BEARING COLLISION DAMAGE This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB22-095

Service Bulletin/Repair Instructions

VOLUNTARY SERVICE CAMPAIGN 2002-2006 ALTIMA AND 2004-2008 MAXIMA FLOOR PAN PC926 will expire on November 1, 2023.

NTB13-027C

Service Bulletin/Repair Instructions

CAN COMMUNICATION – NETWORK DIAGNOSTIC FLOW CHART This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB99-001F

Service Bulletin/Repair Instructions

STRUT AND SHOCK ABSORBER REPLACEMENT GUIDELINES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB99-001e

Service Bulletin/Repair Instructions

STRUT AND SHOCK ABSORBER REPLACEMENT GUIDELINES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB17-030a

Service Bulletin/Repair Instructions

NISSAN; FUEL TANK IS EXTREMELY DIFFICULT TO FILL This bulletin applies to Titan XD vehicles with a gas engine. The update below was sent out to Regions and Dealers in August of this year. We are re-circulating this update to make regional and dealer personnel aware that we are re-notifying customers at this time.

Revision 1-NEVAP

Service Bulletin/Repair Instructions

OBD II EVAP Tube Warranty Enhancement The update below was sent out to Regions and Dealers in August of this year. We are re-circulating this update to make regional and dealer personnel aware that we are re-notifying customers at this time.

NTB17-030

Service Bulletin/Repair Instructions

NISSAN; FUEL TANK IS SLOW OR DIFFICULT TO FILL IF YOU CONFIRM The fuel tank is slow or difficult to fill (filling nozzle shuts off before tank is full). IMPORTANT: Make sure this incident has been duplicated at a gas station by dealer service staff. ACTION Perform the Service Procedure in this bulletin, starting on the next page.

NTB09099A

Service Bulletin/Repair Instructions

IF YOU CONFIRM A refrigerant leak at a refrigerant pipe/hose joint location. ACTIONS 1. Inspect the metal surfaces of the pipe/hose joint for damage or contamination. NOTE: Do not replace a refrigerant pipe, hose, or other A/C component if an o-ring seal will solve the leak incident, if it should occur. 2. If no damage is found to the joint metal surfaces, replace the O-ring seal. See this bulletin for further detail.

NTB09131B

Service Bulletin/Repair Instructions

SERVICE INFORMATION Because of collision damage or other vehicle repair, a replacement "Certification Label" or "VIN Plate / Label" may be needed. These items may be available from Nissan by request if certain criteria are met. This bulletin lists the criteria and provides an application form for such replacements. See this bulletin for further detail.

NTB09081C

Service Bulletin/Repair Instructions

SERVICE INFORMATION The purpose of this bulletin is to give Nissan dealers guidelines to help determine if windshield breakage is covered under warranty or is the customer?s responsibility. Nissan North America (NNA) is not responsible for damage to glass that is a result of objects striking or scratching the glass. However, NNA is responsible for manufacturing issues such as distorted glass and cracks that are due to improper installation or damage to the glass during vehicle assembly. NNA typically does not find any type of cracks in the windshield due to stress after the dealership PDI. See this bulletin for further detail.

NTB13028A

Service Bulletin/Repair Instructions

SERVICE INFORMATION Windshield "foreign material" that is on the surface of the glass in some cases can be cleaned off with a very particular type and grade of steel wool. * Most any foreign material on the surface of the Windshield can be cleaned off by using #0000 super fine steel wool. >The #0000 grade super fine steel wool can be found in most hardware stores. Please see this bulletin for further details.

NTB13088A

Service Bulletin/Repair Instructions

SERVICE INFORMATION This bulletin has compiled Tire Pressure Monitor System (TPMS) and Low Tire Pressure Warning System (LTPWS) information for: - Basic diagnosing of TPMS/LTPWS systems - Radio frequency interference causing a "No Data" (C1708, C1709, C1710, C1711) condition - Sensor leaks - Moving TPMS/LTPWS wheel assemblies from one vehicle to another and TPMS/LTPWS sensor registration - Air pressure changes with altitude and ambient temperatures - Aftermarket tire sealers - Aftermarket wheels - Inflating/deflating tires with TPMS/LTPWS sensors See this bulletin for further detail.

P5216

Service Bulletin/Repair Instructions

To ensure customer satisfaction, Nissan extended the warranty for cracking of the rear sub-frame due to corrosion to a total of 13 years with unlimited mileage on all model year 2002-2005 Nissan Altima and 2004-2005 Nissan Maxima vehicles.

NTB15-059

Service Bulletin/Repair Instructions

NISSAN 2002-2006 ALTIMA AND 2004-2008 BULLETIN INFORMATION INVOLVING FLOOR PAN REPAIR INSTRUCTIONS DUE TO RUST. *LJ

NTB15059

Service Bulletin/Repair Instructions

SERVICE INFORMATION The Service Procedure provided in this bulletin is for the installation of Repair Plates on vehicles that have rust in the floor pan area. See this bulletin for further detail.

NTB15055

Service Bulletin/Repair Instructions

SERVICE INFORMATION After ECM reprogramming, the Calibration Verification Number (CVN) needs to be automatically calculated prior to State emissions testing (also known as Inspection Maintainence, I/M, or SMOG testing depending upon location). Allowing the vehicle to idle for 22 minutes will allow for faster CVN calculation. It is recommended that customers utilize this method if the vehicle needs to be tested for emissions soon after ECM reprogramming. See this bulletin for further detail.

NTB00042D

Service Bulletin/Repair Instructions

SERVICE INFORMATION Changes or modifications to the front seat assembly trim materials may affect the proper operation of the Front Seat-Mounted Side-Impact Supplemental Air Bags and Passenger Occupant Classification Sensor and could result in serious personal injury or death. Nissan STRONGLY RECOMMENDS AGAINST making any change to seat trim materials from the factory equipped condition. This specifically applies to replacing the seat trim with non-factory materials; adding leather/cloth seat covers, seat pads, or seat storage pouches, etc. around or over the seat back and the passenger seat cushion. See this bulletin for further detail.

NTB14107

Service Bulletin/Repair Instructions

SERVICE INFORMATION If a customer describes lack of power or poor acceleration, perform the following checks before attempting any repair: * Check for stored DTCs. * Check if the driver is resting their left foot on the brake pedal while accelerating. Advise the customer not to rest their foot on the brake while accelerating. * Use CONSULT-III plus in Engine Data Monitor to check operation of the brake lamp circuit signal. Monitor the brake switch during the incident; it should be "OFF". Please see this bulletn for further details.

NTB10066A

Service Bulletin/Repair Instructions

SERVICE INFORMATION Related to communication codes U1000, U1001, U1002, U1010: - Always diagnose the communication codes first. - When a module reports a U1000 code, it is typically operating normally; however, there is a communication error external to that module on the CAN network. - U1000 indicates an error. V-CAN diagram or CAN Diag Support Monitor provides data to determine the location of the error. See this bulletin for more information.

NTB-08-055-A

Service Bulletin/Repair Instructions

NISSAN: SRS PRECAUTIONS DURING SERVICE;IMPROPER MAINTENANCE, INCLUDING INCORRECT REMOVAL AND INSTALLATION OF THE SRS, CAN LEAD TO A SERIOUS INJURY OR DEATH CAUSED BY UNINTENTIONAL ACTIVATION OF THE SRS ON ALL NISSAN MODELS WITH THE SRS SYSTEMS. *PE UPDATED 2/21/14. *PE

NTB08055C

Service Bulletin/Repair Instructions

SERVICE INFORMATION Information necessary to service the Supplemental Restraint System (SRS) safely is included in the "RESTRAINTS" section of the Electronic Service Manual (ESM) for each vehicle. IMPORTANT: Turn the ignition switch OFF, disconnect both battery terminals, and wait at least 3 minutes before performing any service on the SRS. See this bulletin for further detail.

NTB-03-074-C

Service Bulletin/Repair Instructions

NISSAN: EXTERIOR LAMP FOGGING. OCCASIONALLY WATER IS NOTICED IN THE EXTERIOR LAMPS. THIS IS GENERALLY NOT DUE TO A DEFECT. ALL CURRENT EXTERIOR LAMP ASSEMBLIES ARE VENTED TO THE ATMOSPHERE (NOT SEALED). THIS IS NECESSARY TO ALLOW FOR EXPANSION AND CONTRACTION OF AIR FROM TEMPERATURE VARIATIONS (WARMER OR COLDER) WITHOUT DAMAGE TO THE LAMP. MOISTURE IN THE AIR SOMETIMES TRAVELS INTO AND OUT OF THE LAMP ASSEMBLY THROUGH THESE VENTS. CERTAIN ENVIRONMENTAL CONDITIONS MAY CAUSE MOISTURE TO CONDENSE. THE FOGGING/CLOUDINESS SHOULD DISAPPEAR OVER TIME WHEN THE LAMP IS IN A DRY ENVIRONMENT. NO MODELS LISTED. *PE UPDATED 5/7/10. *PE UPDATED 12/9/13. *PE

NTB11-002A

Service Bulletin/Repair Instructions

NISSAN: THE VEHICLE HAS A SLOWER THAN NORMAL ACCELERATION FROM A STOP. UPDATED ON 06/08/2011. *KB UPDATED ON 06/13/2011. *RM UPDATED 12/16/2013 *JS

NTB11005D

Service Bulletin/Repair Instructions

Two methods are used to update/upgrade Navigation Map Data: 1. The customer goes to www.nissannavigation.com and is mailed update disc(s) or SD Card and installs data, OR 2. The dealership is mailed update disc(s) and the customer must visit the dealership to have data installed. Use the matrix in this bulletin to determine which method is utilized for each Applied Vehicle. See this bulletin for further detail.

NTB92123D

Service Bulletin/Repair Instructions

Nissan Original Equipment or Genuine Accessory Alloy wheels, along with their finish coating (clear, chrome, titanium, etc.), are specifically developed to achieve Nissan design and performance standards. These Original Equipment or Genuine Accessory wheels are subjected to testing to ensure they meet Nissan's standards. Nissan Original Equipment Alloy or Genuine Accessory wheels subjected to aftermarket chroming may no longer continue to meet these standards and may be seriously damaged. Therefore, Nissan most strongly discourages, and recommends that these wheels NEVER be subjected to, aftermarket chroming. See this bulletinfor further detail.

NTB13027A

Service Bulletin/Repair Instructions

SERVICE INFORMATION This TSB is for troubleshooting of CAN Modules with "Diag-On-CAN" Diagnostics. The flow charts below are meant to troubleshoot current CAN DTCs. The flow charts are intended to diagnose one module at a time; repeat the process as needed for additional control units. Please see this bulleitn for further details.

NTB00033E

Service Bulletin/Repair Instructions

SERVICE INFORMATION - This bulletin is to assist you in responding to customer questions about brake operation, and provides diagnostic and repair information for each item listed, if any should occur. - Most brake incidents fall into the following categories: a. Brake Noise: A squeak, squeal, clunk, or groan that occurs when the brakes are applied or released. b. Brake Judder: A vibration that can be felt in the vehicle, steering wheel or brake pedal when the brakes are applied. c. Pedal Feel: The effort needed to operate the brakes is too high or too low. SERVICE PROCEDURE 1. Verify the condition by road testing the vehicle with the customer. 2. Determine the specific brake incident based on the description in the Service Information above. 3. Follow the appropriate repair procedure(s), listed on the following pages, for your specific incident. See this bulletin for further details.

NTB04094A

Service Bulletin/Repair Instructions

If YOU CONFIRM: A vehicle needs to have the brake rotors resurfaced (front or rear). ACTION: Use the ProCut PFM Series on-car brake lathe to perform brake rotor resurfacing and follow the tips listed in this bulletin. - The ProCut PFM Series brake lathe has been chosen as the approved tool for rotor resurfacing. - The ProCut PFM Series brake lathe can be ordered from TECH-MATE at 1-800-662-2001. - ProCut technical support or service can be obtained by calling 1-800-543-6618. NOTE: Brake rotors may need to be resurfaced during routine brake repair or for brake "judder" incidents. - Brake judder: A brake pedal pulsation and/or steering wheel shimmy when braking that occurs when there is too much thickness variation of the brake rotors (see NTB00-033). See this bulletin for further detail.

NTB98018G

Service Bulletin/Repair Instructions

As part of an enhanced emissions test for Inspection & Maintenance (I/M), some States may require the System Readiness Test (SRT) status be checked. - The SRT is used to indicate whether the engine control module (ECM) has completed self diagnosis of major emissions systems and components. - In these instances the State may require completion of the SRT before permitting the emissions inspection to proceed. Refer to this Bulletin for further details.

NTB-13-038

Service Bulletin/Repair Instructions

NISSAN: LOCK/UNLOCK REQUEST BUTTON ON OUTSIDE HANDLE DOES NOT RESPOND. *JS

NTB99001A

Service Bulletin/Repair Instructions

SERVICE INFORMATION This bulletin provides information to identify: - A leaking strut or a shock absorber that qualifies for replacement under warranty. - A strut or shock absorber that has slight oil seepage, a condition which is considered normal, does not affect strut/shock absorber operation or performance, and does not require replacement. - A strut or shock absorber that should be replaced due to rod resistance/noise issues. See this bulletin for further detail.

P-5216

Service Bulletin/Repair Instructions

NISSAN: SEE DOCUMENT SEARCH BUTTON FOR OWNER LETTER. VOLUNTARY SERVICE CAMPAIGN REAR SUSPENSION MEMBER REPLACEMENT/ BUSHING REPLACEMENT AND SEALING. *JB UPDATED 6/12/12. *PE

NTB12-035

Service Bulletin/Repair Instructions

NISSAN: ECM REPLACEMENT PROCEDURES WITH CONSULT III PLUS. APPLIES TO ALL 2004 AND LATER (DOES NOT APPLY TO LEAF/EV) VEHICLES. *JS

NTB12-029

Service Bulletin/Repair Instructions

NISSAN: ALTIMA, MAXIMA, QUEST; POWER STEERING HOSE SERVICE PART CHANGE. THE HOSE NOW COMES WITHOUT THE PRESSURE SENSOR. DO NOT DAMAGE THE PRESSURE SENSOR UPON REMOVAL OR INSTALLATION. IF ONLY THE PRESSURE SENSOR NEEDS TO BE REPLACED, DO NOT REPLACE ANY HOSES. *JS

NTB-11-080

Service Bulletin/Repair Instructions

NISSAN: AXLE BOLT AND TORQUE INFORMATION. *RM

NTB-11-035

Service Bulletin/Repair Instructions

NISSAN: 2004-2006 MAXIMA. HARSH UPSHIFTS OR DOWNSHIFTS DURING MODERATE ACCELERATION OR WHEN SLOWING. *RM

NTB-11-005

Service Bulletin/Repair Instructions

NISSAN: NAVIGATION MAP DATA UPDATE MATRIX. AFFECTING ALL VEHICLES 2003-11 EXCEPT LEAF, EQUIPPED WITH NAVIGATION SYSTEM. CUSTOMER IS MAILED UPDATE DISC(S) OR SD CARD AND INSTALLS DATA; DEALERSHIP IS MAILED UPDATE DISC(S) AND THE DEALERSHIP INSTALLS DATA WHEN VEHICLE IS BROUGHT IN. *PE

NTB-09-101

Service Bulletin/Repair Instructions

NISSAN: TIRE PRESSURE MONITORING SYSTEM (TPMS) WARNING LIGHT ON/FLASHING. NO MODELS OR MODEL YEARS LISTED. *PE UPDATED ON 08-11-2011. *KB

NTB-09-129

Service Bulletin/Repair Instructions

NISSAN: VENT CONTROL VALVE REPLACEMENT. WHEN REPLACING THE EVAP CANISTER VENT CONTROL VALVE FOR REASON: USE THE ONE LISTED ON PAGE 2; FOR VENT CONTROL VALVE REPLACEMENT PROCEDURE, REFER TO THE APPROPRIATE SECTION OF THE ELECTRONIC SERVICE MANUALS (ESM; WHEN INSTALLING THE NEW VALVE, DO NOT ADD ANY LUBE TO ITS O RING; FOR FRONTIER (D40 SERIES) ONLY, INSTALL THE PROTECTOR LISTED IN PARTS INFORMATION. *PE INCLUDES 2005-09 FRONTIER. UPDATED 12/8/10. *PE

04049

Service Bulletin/Repair Instructions

TRAILER LIGHT WIRING. *MR UPDATED *EH UPDATED 09-12-07. *KB UPDATED 6/21/10. *PE

NTB-10-061

Service Bulletin/Repair Instructions

NISSAN: XENON HEAD LAMP SERVICE. A XENON HEADLAMP IS NOT FUNCTIONING BECAUSE OF AN ISSUE INSIDE THE HEADLAMP ASSEMBLY (AN INTERNAL ISSUE). IN MOST CASES, REPLACEMENT OF A BULB OR HID CONTROL UNIT WILL SOLVE THE INCIDENT. THIS INCLUDES ALL MODELS WITH XENON HEAD LAMPS. NO MODELS LISTED. *PE

NTB-10-046

Service Bulletin/Repair Instructions

NISSAN: REVISED VQ35 ENGINE TIMING CHAIN PROCEDURES. REMOVAL AND INSTALLATION PROCEDURES FOR THE VQ35 ENGINE FRONT TIMING CHAIN CASE AND TIMING CHAINS (PRIMARY AND SECONDARY) HAVE BEE UPDATED TO NO LONGER REQUIRE REMOVAL OF ROCKER COVERS AND INTAKE COLLECTOR. *PE

NTB-05-037A

Service Bulletin/Repair Instructions

NISSAN: THE MIL IS ON AND CODE P1402 EGR OPEN IS STORED IN THE ECM. INSPECT THE EGR VALVE FOR METALLIC DEBRIS. *PE

NTB-09-030

Service Bulletin/Repair Instructions

NISSAN: THE 12 VOLT BATTERY IS AN IMPORTANT PART OF THE VEHICLE ELECTRICAL SYSTEM AND IS REQUIRED TO STAY CONNECTED WHEN THE ENGINE IS RUNNING. TO PREVENT DAMAGE TO VEHICLE ELECTRONIC COMPONENTS FOLLOW THE INSTRUCTIONS/CAUTIONS. NO MODEL YEARS LISTED. *PE

NTB08-034

Service Bulletin/Repair Instructions

2004-2008 MAXIMA; DRIVER/PASSENGER SEATBACK TRIM REPLACEMENT. *NJ

NTB08-049

Service Bulletin/Repair Instructions

NISSAN; SPECIAL AUTOMATIC TRANSMISSION FLUID REQUIREMENT. 2004 TO CURRENT NISSAN VEHICLES. *NJ

NTB05-080A

Service Bulletin/Repair Instructions

AIRFLOWMETER SERVICE. *PE

07026

Service Bulletin/Repair Instructions

2004 - 2008 MAXIMA - DOOR POWER MIRRORS INOPERABLE. *NJ

07042

Service Bulletin/Repair Instructions

BUZZING/WHINING NOISE FROM TIMING CHAIN AREA. *KB

07016

Service Bulletin/Repair Instructions

ABS ACTIVATES WITH NORMAL BRAKING / ABS WARNING LAMP IS ON. *KB UPDATED 08-13-07. *KB

07031

Service Bulletin/Repair Instructions

FRONT BRAKE CALIPER FLUID RESIDUE. *KB

03030

Service Bulletin/Repair Instructions

EXTERIOR LAMP FOGGING. *KB

06075

Service Bulletin/Repair Instructions

DIAGNOSTIC TROUBLE CODE (DTC) P0300, STORED AND IGNITION COILS BLISTERED. *KB

06009

Service Bulletin/Repair Instructions

MIL ON WITH DTC U1000 OR U1010 STORED IN ENGINE CONTROL UNIT. *TT

06029

Service Bulletin/Repair Instructions

ENGINE OIL COOLER GASKET AVAILABLE. *TT

05114

Service Bulletin/Repair Instructions

VOLUNTARY SERVICE CAMPAIGN REAR SUSPENSION MEMBER REPLACEMENT/BUSHING REPLACEMENT AND SEALING. *AK

05114B

Service Bulletin/Repair Instructions

VOLUNTARY SERVICE CAMPAIGN REAR SUSPENSION MEMBER REPLACEMENT/BUSHING REPLACEMENT AND SEALING. *AK

06018

Service Bulletin/Repair Instructions

REAR SIDE MEMBER REPLACEMENT. *TT

05105

Service Bulletin/Repair Instructions

FRONT POWER SEAT NO OR IMPROPER FORWARD / BACKWARD MOVEMENT. *TT

02120A

Service Bulletin/Repair Instructions

ANTILOCK BRAKING SYSTEM (ABS) LIGHT ON AND / OR DIAGNOSTIC TROUBLE CODE FOR ABS WHEEL SPEED SENSOR. *TT

05095

Service Bulletin/Repair Instructions

A RATTLE OR BUZZ NOISE DURING ACCELERATION OR A MALFUNCTION INDICATOR LAMP ON WITH DTC P1273 (A/F SENSOR). *TT

05055

Service Bulletin/Repair Instructions

5 SPEED FWD A/T LEFT SIDE OIL LEAK DIAGNOSTIC. UPDATE *SC

05037

Service Bulletin/Repair Instructions

MIL ON WITH DTC P1402 EGR OPEN CODE STORED. UPDATE *SC

05026

Service Bulletin/Repair Instructions

TCM REPROGRAMMING NEEDED WHEN REPLACING A 5-SPEED A/T ASSEMBLY. *SC

05021

Service Bulletin/Repair Instructions

EXHAUST RATTLE BUZZING NOISE PRESENT DURING ACCELERATION. *EH

04120

Service Bulletin/Repair Instructions

VOLUNTARY SERVICE CAMPAIGN AIR BAG WARNING LIGHT. AIR BAG WARNING LIGHT MAY FLASH EVEN THOUGH THE AIR BAG SYSTEMS IT MONITORS ARE OPERATING PROPERLY. *TT

02022A

Service Bulletin/Repair Instructions

AVAILABLE TOOL: ENGINE SUPPORT BAR (OTC #1724). *NM

04114

Service Bulletin/Repair Instructions

ESSENTIAL TOOL: J-47242 ENGINE SUPPORT TABLE. VARIOUS MODELS INCLUDING 2005 MURANO AND QUEST. *NM

04077

Service Bulletin/Repair Instructions

A/C EVAPORATOR AND EXPANSION VALVE SERVICE. *MJ

Reading this report

Complaint counts are reports filed with NHTSA, not failure rates. A common model collects more of them than a rare one that breaks more often.

2005 Nissan Maxima Service Bulletins: 88 bulletins | CarFathom