Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
NTB09-131C
Service Bulletin/Repair Instructions
CERTIFICATION LABEL AND VIN PLATE REPLACEMENT SERVICE INFORMATION Because of collision damage or other vehicle repair, a replacement “Certification Label” or “VIN Plate/Label” may be needed. HINT: Certification Label = FMVSS (Federal Motor Vehicle Safety Standards) label. These items may be available from Nissan by request if certain criteria are met. This bulletin lists the criteria and provides an application form for such replacements. · The “VIN Plate/Label” (metal plate or vinyl label) is attached to the instrument panel or body on the driver side at the base of the windshield (see Figure 1). · The “Certification Label” (vinyl adhesive label) is located on the lower area of the driver side B-Pillar (see Figure 1).
NTB10-066C
Service Bulletin/Repair Instructions
CAN COMMUNICATION CODES – DIAGNOSTIC TIPS AND GUIDELINES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB13-027D
Service Bulletin/Repair Instructions
CAN COMMUNICATION – NETWORK DIAGNOSTIC FLOW CHART This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB13-107G
Service Bulletin/Repair Instructions
VEHICLE KEY NOT DETECTED / AUTHENTICATED, ENGINE WILL NOT START This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB09-081K
Service Bulletin/Repair Instructions
WINDSHIELD CRACKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB13-028I
Service Bulletin/Repair Instructions
REMOVING FOREIGN MATERIAL FROM THE WINDOW GLASS This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB17-019H
Service Bulletin/Repair Instructions
WINDOW GLASS WARRANTY INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB08-097L
Service Bulletin/Repair Instructions
DIAGNOSIS OF VEHICLE PULL (DRIFT) AND/OR STEERING WHEEL OFF-CENTER This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB23-049
Service Bulletin/Repair Instructions
12 VOLT BATTERY TESTING FOR IN-SERVICE VEHICLES SERVICE INFORMATION The following Service Information lists NNA procedural recommendations for establishing good connections while performing 12V battery testing. These recommendations are expected to promote uniformity during the connection process, therefore reducing the number of incorrect âTest with DCAâ and âReplaceâ results. HINT: If 12 volt batteries are allowed to discharge for a prolonged period of time, battery life may be drastically reduced. This condition may lead to premature battery replacement and customer dissatisfaction. IMPORTANT: ï· CPX-900 is now an accepted testing tool to use along with or in place of the DSS-5000 ï· CPX-900 operating instructions are found at: https://nissancpx900.midtronics.com/ ï· DSS-5000 operating instructions are found at: https://nissandss5000.midtronics.com/ ï· DCA-8000 is now a required testing tool to be used for all warranty replacement decisions. The DCA-8000 is also a more efficient charger than previously available, and will charge any available 12 volt lead acid battery safely and accurately as long as all precautions and inputs are made correctly. The DCA-8000 operating instructions are found at: https://nissandca8000.midtronics.com/
NTB23-053
Service Bulletin/Repair Instructions
SILICONE-BASED LUBRICANT OR GREASE CAN DAMAGE ELECTRICAL COMPONENTS SERVICE INFORMATION Do not apply Silicone-based lubricants or grease to, or around, any interior electrical components. To avoid the risk of death or severe personal injury, do not directly spray Silicone-based lubricant or grease, or inadvertently overspray Silicone-based lubricant or grease onto any interior electrical components. These types of lubricants can be detrimental to the proper operation of electrical components.
NTB13-107F
Service Bulletin/Repair Instructions
VEHICLE KEY NOT DETECTED / AUTHENTICATED, ENGINE WILL NOT START This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB16-003C
Service Bulletin/Repair Instructions
INTELLIGENT KEY REPLACEMENT OR SWAPPING BETWEEN VEHICLES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.
NTB10-145B
Service Bulletin/Repair Instructions
ABS/VDC CAN DIAGNOSIS INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB09-081J
Service Bulletin/Repair Instructions
WINDSHIELD CRACKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB13-028H
Service Bulletin/Repair Instructions
REMOVING FOREIGN MATERIAL FROM THE WINDOW GLASS This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB08-097K
Service Bulletin/Repair Instructions
DIAGNOSIS OF VEHICLE PULL (DRIFT) AND/OR STEERING WHEEL OFF-CENTER This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB10-126C
Service Bulletin/Repair Instructions
WHEEL BEARING COLLISION DAMAGE This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB13-027C
Service Bulletin/Repair Instructions
CAN COMMUNICATION â NETWORK DIAGNOSTIC FLOW CHART This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB17-082E
Service Bulletin/Repair Instructions
DTC P0456 CAUSED BY EVAP LEAK AT VENT CONTROL VALVE O-RING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB99-001F
Service Bulletin/Repair Instructions
STRUT AND SHOCK ABSORBER REPLACEMENT GUIDELINES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB09-031A
Service Bulletin/Repair Instructions
VOLUNTARY SERVICE CAMPAIGN 2009 NISSAN ALTIMA AND MAXIMA; LEFT REAR SUSPENSION KNUCKLE Service Campaign ID # PC005 is no longer active. ï· Repair orders opened after this bulletinâs published date are no longer eligible for reimbursement under Campaign ID # PC005. ï· Discard all previous versions of NTB09-031.
NTB99-001e
Service Bulletin/Repair Instructions
STRUT AND SHOCK ABSORBER REPLACEMENT GUIDELINES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB08-106f
Service Bulletin/Repair Instructions
UPGRADING HDD NAVIGATION MAP DATA This bulletin is no longer active. Please discard previous versions of NTB08-106.
NTB17-018a
Service Bulletin/Repair Instructions
VOLUNTARY SERVICE CAMPAIGN 2009 â 2010 MAXIMA AND ALTIMA ELECTRONIC STEERING COLUMN LOCK Voluntary Service Campaign ID # PC516 is No Longer Active. ï· Repair orders opened after May 28, 2020 are no longer eligible for reimbursement under Campaign ID # PC516. ï· Discard previous versions of NTB17-018.
EXPIRATION NOTIF
Service Bulletin/Repair Instructions
Expiration Notification â Electronic Steering Column Lock (ESCL) Voluntary Service Campaign UPDATE May 14, 2020 Please discard earlier versions of this bulletin. The original announcement from February 21, 2017 has been revised to include: ï· Service Comm will deactivate PC516 on any unremedied VINs on May 29, 2020. ï· Dealers may continue to schedule and repair vehicles eligible for this service campaign up to and including May 28, 2020. ï· Vehicles presented for repair after May 28, 2020 will not be covered by this service campaign and any repair will be performed at customer expense if no service contract exists. o Either of the following parts may be used for service repairs at customer expense after May 28, 2020: ï§ Electronic Steering Column Box (ESCB) 48708-9N00A ï§ Electronic Steering Column Lock (ESCL) 48700-9N00B
NTB17-082b
Service Bulletin/Repair Instructions
NISSAN; DTC P0456 CAUSED BY EVAP LEAK AT VENT CONTROL VALVE O-RING This bulletin does NOT apply to LEAF vehicles and Titan XD vehicles with V8 diesel engine. This bulletin has been amended. See Amendment History on the last page. Please discard previous versions of this bulletin.
NTB17-030a
Service Bulletin/Repair Instructions
NISSAN; FUEL TANK IS EXTREMELY DIFFICULT TO FILL This bulletin applies to Titan XD vehicles with a gas engine. The update below was sent out to Regions and Dealers in August of this year. We are re-circulating this update to make regional and dealer personnel aware that we are re-notifying customers at this time.
Revision 1-NEVAP
Service Bulletin/Repair Instructions
OBD II EVAP Tube Warranty Enhancement The update below was sent out to Regions and Dealers in August of this year. We are re-circulating this update to make regional and dealer personnel aware that we are re-notifying customers at this time.
NTB17-121a
Service Bulletin/Repair Instructions
2009 ? 2014 MAXIMA DOOR MIRROR TURN SIGNAL REPLACEMENT This bulletin has been amended. The PARTS INFORMATION section has been updated. No other change were made. Please discard previous versions of this bulletin.
NTB17-121
Service Bulletin/Repair Instructions
2009 ? 2014 MAXIMA DOOR MIRROR TURN SIGNAL REPLACEMENT IF YOU CONFIRM If you confirm the turn signal in the left or right side door mirror assembly needs to be replaced. ACTION Replace ONLY the turn signal. Replacement of the entire door mirror assembly is no longer required.
NTB17-082a
Service Bulletin/Repair Instructions
NISSAN; DTC P0456 CAUSED BY EVAP LEAK AT VENT CONTROL VALVE O-RING This bulletin has been amended. The APPLIED VEHICLES and CLAIMS INFORMATION sections have been revised. No other changes have been made. Please discard previous versions of this bulletin.
NTB17-082
Service Bulletin/Repair Instructions
NISSAN; DTC P0456 CAUSED BY EVAP LEAK AT VENT CONTROL VALVE O-RING IF YOU CONFIRM The MIL is ON in an APPLIED VEHICLE with DTC P0456 (EVAP VERY SML LEAK) AND - DTC P0456 is not caused by a loose fuel fill cap (refer to NTB13-097). - An EVAP leak has been detected where the vent control valve mounts to the canister. - The vent control valve O-ring seal is determined to be the cause. ACTION 1. DO NOT REPLACE the vent control valve. 2. Replace the vent control valve O-ring seal (O-ring). - Refer to SERVICE PROCEDURE on page 2.
NTB17-030
Service Bulletin/Repair Instructions
NISSAN; FUEL TANK IS SLOW OR DIFFICULT TO FILL IF YOU CONFIRM The fuel tank is slow or difficult to fill (filling nozzle shuts off before tank is full). IMPORTANT: Make sure this incident has been duplicated at a gas station by dealer service staff. ACTION Perform the Service Procedure in this bulletin, starting on the next page.
PC516
Service Bulletin/Repair Instructions
Electronic Steering Column Lock (ESCL) Voluntary Service Campaign ***** Campaign Summary***** Nissan is conducting a voluntary service campaign on specific MY2009-10 Nissan Altima (L32), Altima Coupe (CL32), Altima Hybrid (L32H), and Maxima (A35) vehicles to replace the existing ESCL with an Electronic Steering Column Box (ESCB). The ESCL locks the steering wheel when the vehicle is parked and turned off to help prevent theft. On some vehicles, due to a manufacturing regularity, the ESCL may malfunction after the vehicle is locked and could prevent the engine from starting. This condition, should it occur, will only occur when attempting to start the vehicle, and not while driving. The ESCB will replace the ESCL assembly, but will no longer lock the steering wheel when the vehicle is parked and turned off. The steering wheel locking function is not necessary as the vehicle is also equipped with an anti-theft immobilizer to help prevent theft. Installation of the ESCB will eliminate the possibility of a no-start condition related to the manufacturing irregularity on the ESCL. ***** What Dealers Should Do ***** 1. Verify if vehicles are affected by this Voluntary Service Campaign using Service Comm I.D. PC516. 2. Dealers are requested to repair any affected vehicles in dealer new or pre-owned inventory to ensure customer satisfaction. 3. Dealers should use NTB17-018 to correct any vehicles subject to this campaign. 4. Once repaired, dealers should submit the claim, using the claims coding provided, and release the vehicle.
PC516OL
Service Bulletin/Repair Instructions
Nissan is conducting a voluntary service campaign on specific MY2009-10 Nissan Altima (L32), Altima Coupe (CL32), Altima Hybrid (L32H), and Maxima (A35) vehicles to replace the existing ESCL with an Electronic Steering Column Box (ESCB).
NTB17-018
Service Bulletin/Repair Instructions
VOLUNTARY SERVICE CAMPAIGN 2009 ? 2010 MAXIMA AND ALTIMA ELECTRONIC STEERING COLUMN LOCK INTRODUCTION Nissan is conducting a Voluntary Service Campaign to replace the Electronic Steering Column Lock (Steering Lock Unit) on certain specific 2009 ? 2010 model year Maxima and Altima vehicles. This issue does not affect steering or engine operation when the vehicle is already running. This service will be performed at no charge to the customer for parts or labor. NOTE: - After completing this campaign, the steering column will not lock when the ignition is OFF, as it did before. - The new steering lock unit does not have a column lock function. IDENTIFICATION NUMBER Nissan has assigned identification number PC516 to this campaign. This number must appear on all communications and documentation of any nature dealing with this campaign. DEALER RESPONSIBILITY Dealers are to repair vehicles falling within range of this campaign that enter the service department. This includes vehicles purchased from private parties, vehicles presented by transient (tourists) owners, and vehicles in a dealer?s inventory.
NTB09099A
Service Bulletin/Repair Instructions
IF YOU CONFIRM A refrigerant leak at a refrigerant pipe/hose joint location. ACTIONS 1. Inspect the metal surfaces of the pipe/hose joint for damage or contamination. NOTE: Do not replace a refrigerant pipe, hose, or other A/C component if an o-ring seal will solve the leak incident, if it should occur. 2. If no damage is found to the joint metal surfaces, replace the O-ring seal. See this bulletin for further detail.
NTB09131B
Service Bulletin/Repair Instructions
SERVICE INFORMATION Because of collision damage or other vehicle repair, a replacement "Certification Label" or "VIN Plate / Label" may be needed. These items may be available from Nissan by request if certain criteria are met. This bulletin lists the criteria and provides an application form for such replacements. See this bulletin for further detail.
NTB09081C
Service Bulletin/Repair Instructions
SERVICE INFORMATION The purpose of this bulletin is to give Nissan dealers guidelines to help determine if windshield breakage is covered under warranty or is the customer?s responsibility. Nissan North America (NNA) is not responsible for damage to glass that is a result of objects striking or scratching the glass. However, NNA is responsible for manufacturing issues such as distorted glass and cracks that are due to improper installation or damage to the glass during vehicle assembly. NNA typically does not find any type of cracks in the windshield due to stress after the dealership PDI. See this bulletin for further detail.
NTB13028A
Service Bulletin/Repair Instructions
SERVICE INFORMATION Windshield "foreign material" that is on the surface of the glass in some cases can be cleaned off with a very particular type and grade of steel wool. * Most any foreign material on the surface of the Windshield can be cleaned off by using #0000 super fine steel wool. >The #0000 grade super fine steel wool can be found in most hardware stores. Please see this bulletin for further details.
NTB13088A
Service Bulletin/Repair Instructions
SERVICE INFORMATION This bulletin has compiled Tire Pressure Monitor System (TPMS) and Low Tire Pressure Warning System (LTPWS) information for: - Basic diagnosing of TPMS/LTPWS systems - Radio frequency interference causing a "No Data" (C1708, C1709, C1710, C1711) condition - Sensor leaks - Moving TPMS/LTPWS wheel assemblies from one vehicle to another and TPMS/LTPWS sensor registration - Air pressure changes with altitude and ambient temperatures - Aftermarket tire sealers - Aftermarket wheels - Inflating/deflating tires with TPMS/LTPWS sensors See this bulletin for further detail.
NTB14057A
Service Bulletin/Repair Instructions
SERVICE INFORMATION The information in this bulletin is provided to help ensure correct diagnosis and repair of fluid leaks. All fluid leaks, when properly diagnosed, should be repaired (whether under warranty or customer pay) to ensure proper vehicle operation. However, certain normal operating conditions can be misdiagnosed as a leak requiring repair. Unnecessary repair or replacement of parts in connection with incorrectly diagnosed "leaks" can negatively impact customer satisfaction, be time consuming and costly, and if not performed correctly can lead to future repairs. See this bulletin for further detail.
NTB15060
Service Bulletin/Repair Instructions
SERVICE INFORMATION When servicing run flat tires or low profile tires: - Special equipment and procedures are required to avoid damage. - Specifically, Tire Pressure Monitor transmitters (TPMS sensors) can be damaged when improperly dismounting and mounting tires. - TPMS sensors becoming damaged during mounting or dismounting tires are not covered under warranty. - To avoid such damage, ensure that the tire changer being used and the operator of the tire changer is capable of servicing run flat and low profile tires. - Operator?s manuals for such tire changers must be followed. See this bulletin for further detail.
NTB15055
Service Bulletin/Repair Instructions
SERVICE INFORMATION After ECM reprogramming, the Calibration Verification Number (CVN) needs to be automatically calculated prior to State emissions testing (also known as Inspection Maintainence, I/M, or SMOG testing depending upon location). Allowing the vehicle to idle for 22 minutes will allow for faster CVN calculation. It is recommended that customers utilize this method if the vehicle needs to be tested for emissions soon after ECM reprogramming. See this bulletin for further detail.
NTB99060G
Service Bulletin/Repair Instructions
SERVICE INFORMATION NOTE - Failure to follow the procedures in this bulletin may result in the denial of a warranty claim. In an effort to protect the paint finish, Paint Guard Film (PGF) is applied on many new Nissan vehicles. Paint Guard Film is a temporary white plastic protective film that is applied by the factory to the horizontal painted surfaces of the vehicle. The PGF protects the paint finish during vehicle handling, transportation and storage from harmful elements such as acid rain, iron particles, bird droppings, tree sap and other environmental contaminants. NOTE - Paint Guard Film CANNOT remain on the vehicle for more than six months after the vehicle's manufacture date. PGF must be removed at the end of six months. See this bulletin for further detail.
NTB12078A
Service Bulletin/Repair Instructions
SERVICE INFORMATION When diagnosing possible power steering gear (rack and pinion steering rack, or steering rack) leak issues, it may appear the steering rack is leaking when actually, it?s not. Use this service bulletin to help make a more accurate diagnosis of the steering rack. See this bulletin for further detail.
NTB00042D
Service Bulletin/Repair Instructions
SERVICE INFORMATION Changes or modifications to the front seat assembly trim materials may affect the proper operation of the Front Seat-Mounted Side-Impact Supplemental Air Bags and Passenger Occupant Classification Sensor and could result in serious personal injury or death. Nissan STRONGLY RECOMMENDS AGAINST making any change to seat trim materials from the factory equipped condition. This specifically applies to replacing the seat trim with non-factory materials; adding leather/cloth seat covers, seat pads, or seat storage pouches, etc. around or over the seat back and the passenger seat cushion. See this bulletin for further detail.
NTB13015A
Service Bulletin/Repair Instructions
SERVICE INFORMATION DTC B2190 (NATS ANTENNA AMP) can be stored for the following reasons: 1. Something other than an Intelligent Key is inserted into the Key-Slot. 2. An Intelligent Key issue. 3. A wiring issue between the Key-Slot and the BCM. 4. A Key-Slot issue. If DTC B2190 is stored due to 1 or 2 above, it will not erase, or go to "PAST", until a known good registered Intelligent Key is inserted into the Key-Slot. For DTC B2190 diagnosis; first perform the Service Manual DTC Confirmation Procedure. See this bulletin for further detail.
NTB14107
Service Bulletin/Repair Instructions
SERVICE INFORMATION If a customer describes lack of power or poor acceleration, perform the following checks before attempting any repair: * Check for stored DTCs. * Check if the driver is resting their left foot on the brake pedal while accelerating. Advise the customer not to rest their foot on the brake while accelerating. * Use CONSULT-III plus in Engine Data Monitor to check operation of the brake lamp circuit signal. Monitor the brake switch during the incident; it should be "OFF". Please see this bulletn for further details.
NTB12116A
Service Bulletin/Repair Instructions
IF YOU CONFIRM - MIL is on with DTC's P0014 and/or P0024. - Customer describes a hesitation at speeds below 15 MPH after the oil was changed. ACTION Replace left and right cylinder bank's "Exhaust Valve Control Magnet Retarder". Please see this bulletin for further details.
NTB14011
Service Bulletin/Repair Instructions
SERVICE INFORMATION When replacing the Electronic Steering Column Lock, there are two possible service parts that may be shipped to the dealer: 48700-9N00B or 48700-1NC0A. These part numbers are interchangeable. If you receive Electronic Steering Column Lock P/N 48700-1NC0A, the bolts that hold it in place may not line up. You may not be able to start the bolt threads. If you encounter this condition, see this bulletin for further detail.
NTB10066A
Service Bulletin/Repair Instructions
SERVICE INFORMATION Related to communication codes U1000, U1001, U1002, U1010: - Always diagnose the communication codes first. - When a module reports a U1000 code, it is typically operating normally; however, there is a communication error external to that module on the CAN network. - U1000 indicates an error. V-CAN diagram or CAN Diag Support Monitor provides data to determine the location of the error. See this bulletin for more information.
NTB-14-011
Service Bulletin/Repair Instructions
NISSAN: WITH ELECTRONIC STEERING COLUMN LOCK, BOLTS MAY NOT LINE UP TO HOLD IN PLACE AND BOLT THREADS MAY NOT BE STARTED AND A SMALL AMOUNT METAL FROM EDGES IS REMOVED BY USING A HAND FILE. *PE
NTB08055C
Service Bulletin/Repair Instructions
SERVICE INFORMATION Information necessary to service the Supplemental Restraint System (SRS) safely is included in the "RESTRAINTS" section of the Electronic Service Manual (ESM) for each vehicle. IMPORTANT: Turn the ignition switch OFF, disconnect both battery terminals, and wait at least 3 minutes before performing any service on the SRS. See this bulletin for further detail.
NTB12091A
Service Bulletin/Repair Instructions
SERVICE INFORMATION Replacement Engine Control Modules (ECMs) for many newer Nissan vehicles are now "Blank" ECMs. Blank ECMs come without software and must be programmed (not reprogrammed) before they will function. See this bulletin for further detail.
NTB-12-071-A
Service Bulletin/Repair Instructions
NISSAN: KNOCKING NOISE COMING FROM NUMBER 1 CRANKSHAFT MAIN BEARING, WAS NOT HEARD AT COLD START, WHEN VEHICLE IS LIFTED, KNOCKING IS HEARD, OR AT WARM IDLE, NOT HEARD AT HIGHWAY SPEEDS OR SITTING WITH RADIO ON. MODEL 2009-2014 MAXIMA *PE
NTB12071A
Service Bulletin/Repair Instructions
IF YOU CONFIRM A knock noise coming from the # 1 crankshaft main bearing: ACTION 1. Remove the # 1 main bearing (upper and lower halves), per the Service Procedure in this bulletin. 2. Select and install a new # 1 main bearing that is one grade higher (thicker) than the one removed. See this bulletin for further detail.
NTB-03-074-C
Service Bulletin/Repair Instructions
NISSAN: EXTERIOR LAMP FOGGING. OCCASIONALLY WATER IS NOTICED IN THE EXTERIOR LAMPS. THIS IS GENERALLY NOT DUE TO A DEFECT. ALL CURRENT EXTERIOR LAMP ASSEMBLIES ARE VENTED TO THE ATMOSPHERE (NOT SEALED). THIS IS NECESSARY TO ALLOW FOR EXPANSION AND CONTRACTION OF AIR FROM TEMPERATURE VARIATIONS (WARMER OR COLDER) WITHOUT DAMAGE TO THE LAMP. MOISTURE IN THE AIR SOMETIMES TRAVELS INTO AND OUT OF THE LAMP ASSEMBLY THROUGH THESE VENTS. CERTAIN ENVIRONMENTAL CONDITIONS MAY CAUSE MOISTURE TO CONDENSE. THE FOGGING/CLOUDINESS SHOULD DISAPPEAR OVER TIME WHEN THE LAMP IS IN A DRY ENVIRONMENT. NO MODELS LISTED. *PE UPDATED 5/7/10. *PE UPDATED 12/9/13. *PE
NTB-09-020-F
Service Bulletin/Repair Instructions
NISSAN: A LOOSE FUEL FILL CAP IS THE CAUSE OF EVAP LEAK DTCS (P0442, P0455, P0456) STORED ON SOME VEHICLES. MODEL YEARS 2007-2011. MODEL NOT LISTED. *PE
NTB09020F
Service Bulletin/Repair Instructions
SERVICE INFORMATION If one or more of these EVAP leak DTCs are stored (P0442, P0455, P0456) on a 2007 through 2011 Nissan vehicle, a loose fuel fill cap may be the cause. Use the following resources to perform diagnostics and confirm the cause of stored DTCs. ASIST: - Appropriate Service Manual diagnostic procedures - Applicable Technical Service Bulletins (TSB). Leak Test: - With CONSULT-III plus - WORK SUPPORT >> EVAP SYSTEM CLOSE. NOTE: Use Essential Tool J-42909 or equivalent to pressurize the EVAP system. - With a "Smoke" leak detection machine. Refer to the machine's Operator's Manual for proper use. Make sure the customer is informed of the proper fuel filler cap installation.
NTB11-002A
Service Bulletin/Repair Instructions
NISSAN: THE VEHICLE HAS A SLOWER THAN NORMAL ACCELERATION FROM A STOP. UPDATED ON 06/08/2011. *KB UPDATED ON 06/13/2011. *RM UPDATED 12/16/2013 *JS
NTB11005D
Service Bulletin/Repair Instructions
Two methods are used to update/upgrade Navigation Map Data: 1. The customer goes to www.nissannavigation.com and is mailed update disc(s) or SD Card and installs data, OR 2. The dealership is mailed update disc(s) and the customer must visit the dealership to have data installed. Use the matrix in this bulletin to determine which method is utilized for each Applied Vehicle. See this bulletin for further detail.
NTB92123D
Service Bulletin/Repair Instructions
Nissan Original Equipment or Genuine Accessory Alloy wheels, along with their finish coating (clear, chrome, titanium, etc.), are specifically developed to achieve Nissan design and performance standards. These Original Equipment or Genuine Accessory wheels are subjected to testing to ensure they meet Nissan's standards. Nissan Original Equipment Alloy or Genuine Accessory wheels subjected to aftermarket chroming may no longer continue to meet these standards and may be seriously damaged. Therefore, Nissan most strongly discourages, and recommends that these wheels NEVER be subjected to, aftermarket chroming. See this bulletinfor further detail.
NTB13027A
Service Bulletin/Repair Instructions
SERVICE INFORMATION This TSB is for troubleshooting of CAN Modules with "Diag-On-CAN" Diagnostics. The flow charts below are meant to troubleshoot current CAN DTCs. The flow charts are intended to diagnose one module at a time; repeat the process as needed for additional control units. Please see this bulleitn for further details.
NTB00033E
Service Bulletin/Repair Instructions
SERVICE INFORMATION - This bulletin is to assist you in responding to customer questions about brake operation, and provides diagnostic and repair information for each item listed, if any should occur. - Most brake incidents fall into the following categories: a. Brake Noise: A squeak, squeal, clunk, or groan that occurs when the brakes are applied or released. b. Brake Judder: A vibration that can be felt in the vehicle, steering wheel or brake pedal when the brakes are applied. c. Pedal Feel: The effort needed to operate the brakes is too high or too low. SERVICE PROCEDURE 1. Verify the condition by road testing the vehicle with the customer. 2. Determine the specific brake incident based on the description in the Service Information above. 3. Follow the appropriate repair procedure(s), listed on the following pages, for your specific incident. See this bulletin for further details.
NTB04094A
Service Bulletin/Repair Instructions
If YOU CONFIRM: A vehicle needs to have the brake rotors resurfaced (front or rear). ACTION: Use the ProCut PFM Series on-car brake lathe to perform brake rotor resurfacing and follow the tips listed in this bulletin. - The ProCut PFM Series brake lathe has been chosen as the approved tool for rotor resurfacing. - The ProCut PFM Series brake lathe can be ordered from TECH-MATE at 1-800-662-2001. - ProCut technical support or service can be obtained by calling 1-800-543-6618. NOTE: Brake rotors may need to be resurfaced during routine brake repair or for brake "judder" incidents. - Brake judder: A brake pedal pulsation and/or steering wheel shimmy when braking that occurs when there is too much thickness variation of the brake rotors (see NTB00-033). See this bulletin for further detail.
NTB-13-006
Service Bulletin/Repair Instructions
NISSAN: ON CERTAIN VEHICLES, THE STEERING WHEEL SWITCHES MAY NEED REPLACING BUT NOT THE DRIVER AIR BAG MODULE. MODELS 2009-13 MAXIMA. *PE
NTB13006
Service Bulletin/Repair Instructions
SERVICE INFORMATION If you confirm there is a need to replace the steering wheel switches on an Applied Vehicle for any reason: - Do not replace the driver air bag module. The steering wheel switches are now available as a separate service part. - Refer to the Service Procedure in this bulletin for steering wheel switch removal and installation instructions. See this bulletin for more detail.
NTB13063
Service Bulletin/Repair Instructions
IF YOU CONFIRM: The front passenger seatback has a greater than normal vibration at highway speeds AND There are no other shake or vibrations with the vehicle. ACTION: Use the REPAIR FLOW CHART on page 3 to determine the repair(s) to be performed. NOTES: - The description under IF YOU CONFIRM must exist for this bulletin to apply. - If determined the passenger seatback frame will be replaced: - The headrest, seatback pad, seatback frame bolts, and side airbag nuts must also be replaced. - The seatback trim and seatback board will be reused. - Do not replace the seat cushion and frame assembly or complete seat assembly. See this bulletin for further detail.
NTB98018G
Service Bulletin/Repair Instructions
As part of an enhanced emissions test for Inspection & Maintenance (I/M), some States may require the System Readiness Test (SRT) status be checked. - The SRT is used to indicate whether the engine control module (ECM) has completed self diagnosis of major emissions systems and components. - In these instances the State may require completion of the SRT before permitting the emissions inspection to proceed. Refer to this Bulletin for further details.
NTB08106E
Service Bulletin/Repair Instructions
SERVICE INFORMATION The navigation system in the Applied Vehicles has an HDD (Hard Disc Drive) map data storage system. This bulletin contains the information and instructions for updating/upgrading the map data with a new version. See this bulletin for further detail.
NTB13-039
Service Bulletin/Repair Instructions
NISSAN: CRUISE CONTROL WILL NOT SET AND DTC P0605 IS STORED. *JS
NTB13039
Service Bulletin/Repair Instructions
SERVICE INFORMATION Improper adjustment or operation of the ASCD brake switch can cause the Automatic Speed Control Device (ASCD) to "not set" and/or DTC P0605 (ECM) to store. See this bulletin for further detail.
NTB-13-038
Service Bulletin/Repair Instructions
NISSAN: LOCK/UNLOCK REQUEST BUTTON ON OUTSIDE HANDLE DOES NOT RESPOND. *JS
NTB13038
Service Bulletin/Repair Instructions
SERVICE INFORMATION The "Lock / Unlock request buttons" that are located on the outside door handles of vehicles with Intelligent Key can be disabled (or enabled) through either the "Comfort & Conv." settings of the Audio/Visual/Navigation system, orthrough the "Combination Meter settings" depending on the vehicle model, year and trim level. NOTE: In some instances this feature may be unintentionally disabled. Please verify the status of this feature before any further diagnostic is performed. Please see this bulletin for further details.
NTB99001A
Service Bulletin/Repair Instructions
SERVICE INFORMATION This bulletin provides information to identify: - A leaking strut or a shock absorber that qualifies for replacement under warranty. - A strut or shock absorber that has slight oil seepage, a condition which is considered normal, does not affect strut/shock absorber operation or performance, and does not require replacement. - A strut or shock absorber that should be replaced due to rod resistance/noise issues. See this bulletin for further detail.
MAILQ
Service Bulletin/Repair Instructions
Nissan has decided in the interest of customer satisfaction, to extend the warranty for the Electronic Steering Column Lock unit on all 2009 Altima and Maxima vehicles.
NTB11012B
Service Bulletin/Repair Instructions
SERVICE INFORMATION If a CD/DVD Player incident is noted, a possible cause may be improper CD/DVD disc care, condition, or usage. This bulletin provides updated CD/DVD Player operation instructions to avoid potential incidents/customer concerns caused by improper care and usage of CD/DVD discs. To aid in solving customer concerns, use the guidelines in this bulletin when speaking to customers or inspecting incident vehicles. - Customers must not use discs that are warped, scratched, chipped, cracked, have abnormal edges or are otherwise damaged. Damaged or poor condition discs may cause the Player internal mechanism to jam or have optical pick-up errors. NOTE - Do not make a Warranty claim against a Player that will not play damaged or poor condition discs as described in this bulletin. See this bulletin for further detail.
NTB12093A
Service Bulletin/Repair Instructions
IF YOU CONFIRM: After having been parked overnight in ambient temperatures between 5°C to -25°C (40°F to -14°F) the vehicle is hard to start or cranks and will not start. And * Occurs only on first attempts to start before engine begins running. And * Will not occur after engine has been started and run for any period of time. ACTIONS: * Confirm this bulletin applies and if so reprogram the ECM. See this bulleitn for further details.
NTB-10-102-A
Service Bulletin/Repair Instructions
NISSAN: BULLETIN REGARDING DIAGNOSIS OF ABS/VDC WHEEL SPEED SENSOR. MODEL 2007-2013 NISSAN. *PE
NTB-09-019-A
Service Bulletin/Repair Instructions
NISSAN: RAIN SENSORS MAY OPERATE, INTERMITTENTLY OR UNEXPECTEDLY, WHEN EXHAUST GAS, MOISTURE, FINGERPRINTS, DIRT, OR INSECTS ARE NEAR OR AROUND RAIN SENSORS. NO MODELS OR MODEL YEARS LISTED. *PE
NTB12-035
Service Bulletin/Repair Instructions
NISSAN: ECM REPLACEMENT PROCEDURES WITH CONSULT III PLUS. APPLIES TO ALL 2004 AND LATER (DOES NOT APPLY TO LEAF/EV) VEHICLES. *JS
NTB12-30
Service Bulletin/Repair Instructions
NISSAN: ALTIMA, MAXIMA; POWER STEERING HOSE SERVICE PART CHANGE. THE HOSE NOW COMES WITHOUT THE PRESSURE SENSOR. DO NOT DAMAGE PRESSURE SENSOR UPON REMOVAL OR INSTALLATION. IF ONLY THE PRESSURE SENSOR NEEDS TO BE REPLACED, DO NOT REPLACE ANY HOSES. *JS
NTB12-009
Service Bulletin/Repair Instructions
NISSAN: DOOR LOCK/UNLOCK INOPERATIVE WITH INTELLIGENT KEY. *KB
NTB-11-080
Service Bulletin/Repair Instructions
NISSAN: AXLE BOLT AND TORQUE INFORMATION. *RM
NTB-11-037
Service Bulletin/Repair Instructions
NISSAN: THERE IS A TROUBLE CODE STORED DUE TO SOFTWARE. SOME 2009 VEHICLES. *RM
NTB-10-057
Service Bulletin/Repair Instructions
NISSAN: THE MIL IS ON WITH ONE OR MORE OF THE FOLLOWING DTCS STORED: P0442/P0448/P0455/P0456 AND EVAP VENT CONTROL VALVE IS STUCK OPEN OR WILL NOT SEAL WHEN OPERATED/CLOSED. REPLACE VENT CONTROL VALVE; INSTALL FILTER KIT LISTED IN PARTS INFORMATION; AND CLEAR ANY DTCS STORED IN THE ECM. *PE UPDATED 6/15/11. *PE
NTB-10-017A
Service Bulletin/Repair Instructions
NISSAN: THE FUEL GUAGE IS ERRATIC, THE MALFUNCTION LIGHT IS ON, AND THERE ARE STORED TROUBLE CODES. *RM
NTB-11-005
Service Bulletin/Repair Instructions
NISSAN: NAVIGATION MAP DATA UPDATE MATRIX. AFFECTING ALL VEHICLES 2003-11 EXCEPT LEAF, EQUIPPED WITH NAVIGATION SYSTEM. CUSTOMER IS MAILED UPDATE DISC(S) OR SD CARD AND INSTALLS DATA; DEALERSHIP IS MAILED UPDATE DISC(S) AND THE DEALERSHIP INSTALLS DATA WHEN VEHICLE IS BROUGHT IN. *PE
SB-09-092
Service Bulletin/Repair Instructions
NISSAN: THE DRIVER'S SEAT BOTTOM VERY SLIGHTLY ROCKS AND/OR SHIFTS BACK AND FORTH WHEN ACCELERATIONG, BRAKING, OR WHEN MAKING A TURN. REPLACE THE DRIVER SEAT FRAME (ADJUSTER ASSEMBLY) WITH A NEW ONE. *PE UPDATED 1/24/11. *PE
NTB-09-101
Service Bulletin/Repair Instructions
NISSAN: TIRE PRESSURE MONITORING SYSTEM (TPMS) WARNING LIGHT ON/FLASHING. NO MODELS OR MODEL YEARS LISTED. *PE UPDATED ON 08-11-2011. *KB
NTB-09-129
Service Bulletin/Repair Instructions
NISSAN: VENT CONTROL VALVE REPLACEMENT. WHEN REPLACING THE EVAP CANISTER VENT CONTROL VALVE FOR REASON: USE THE ONE LISTED ON PAGE 2; FOR VENT CONTROL VALVE REPLACEMENT PROCEDURE, REFER TO THE APPROPRIATE SECTION OF THE ELECTRONIC SERVICE MANUALS (ESM; WHEN INSTALLING THE NEW VALVE, DO NOT ADD ANY LUBE TO ITS O RING; FOR FRONTIER (D40 SERIES) ONLY, INSTALL THE PROTECTOR LISTED IN PARTS INFORMATION. *PE INCLUDES 2005-09 FRONTIER. UPDATED 12/8/10. *PE
04049
Service Bulletin/Repair Instructions
TRAILER LIGHT WIRING. *MR UPDATED *EH UPDATED 09-12-07. *KB UPDATED 6/21/10. *PE
NTB-10-061
Service Bulletin/Repair Instructions
NISSAN: XENON HEAD LAMP SERVICE. A XENON HEADLAMP IS NOT FUNCTIONING BECAUSE OF AN ISSUE INSIDE THE HEADLAMP ASSEMBLY (AN INTERNAL ISSUE). IN MOST CASES, REPLACEMENT OF A BULB OR HID CONTROL UNIT WILL SOLVE THE INCIDENT. THIS INCLUDES ALL MODELS WITH XENON HEAD LAMPS. NO MODELS LISTED. *PE
NTB-09-031
Service Bulletin/Repair Instructions
NISSAN: THE LEFT HAND REAR SUSPENSION KNUCKLE MAY NOT BE MANUFACTURED TO SPECIFICATION, WHICH MAY RESULT IN NOISE OR VIBRATION UNDER CERTAIN CIRCUMSTANCES. (SEDANS, COUPES, AND HYBRIDS). *PE
NTB-09-030
Service Bulletin/Repair Instructions
NISSAN: THE 12 VOLT BATTERY IS AN IMPORTANT PART OF THE VEHICLE ELECTRICAL SYSTEM AND IS REQUIRED TO STAY CONNECTED WHEN THE ENGINE IS RUNNING. TO PREVENT DAMAGE TO VEHICLE ELECTRONIC COMPONENTS FOLLOW THE INSTRUCTIONS/CAUTIONS. NO MODEL YEARS LISTED. *PE