Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
NTB09-131C
Service Bulletin/Repair Instructions
CERTIFICATION LABEL AND VIN PLATE REPLACEMENT SERVICE INFORMATION Because of collision damage or other vehicle repair, a replacement “Certification Label” or “VIN Plate/Label” may be needed. HINT: Certification Label = FMVSS (Federal Motor Vehicle Safety Standards) label. These items may be available from Nissan by request if certain criteria are met. This bulletin lists the criteria and provides an application form for such replacements. · The “VIN Plate/Label” (metal plate or vinyl label) is attached to the instrument panel or body on the driver side at the base of the windshield (see Figure 1). · The “Certification Label” (vinyl adhesive label) is located on the lower area of the driver side B-Pillar (see Figure 1).
WBI/21-002
Service Bulletin/Repair Instructions
CAMPAIGN BULLETIN CVT Warranty Extension In an effort to assure customer satisfaction, demonstrate our confidence in continuously variable transmissions (CVTs), and to address customer concerns including those expressed by customers in a class action, Nissan will extend the warranty coverage on the CVT. The warranty extension includes the CVT assembly and internal CVT components, gaskets, and seals, CVT control valve body, torque converter, cooler kit (if applicable), Automatic Transmission Control Unit (ATCU) and reprogramming of the Transmission Control Module (TCM), on the vehicles listed in this announcement. The warranty is being extended from its original duration of 60 months/60,000 miles to 84 months/84,000 miles (whichever occurs first). Coverage of other vehicle components remains unchanged, and all other terms, conditions, limitations and exclusions of Nissan’s New Vehicle Limited Warranty continue to apply. ***** What Dealers Should Do ***** 1. If an owner contacts a dealer with a CVT concern in an owned or leased vehicle, verify warranty coverage for the specific VIN and then inform the customer of any diagnostic charges. NOTE: Some owners may have opted out of the warranty extension by excluding themselves from the class action settlement, thus it is important to check the VIN for each vehicle to verify coverage. 2. Use the appropriate Technical Service Bulletin (TSB) and/or Electronic Service Manual (ESM) to diagnose the root cause of the customer concern and identify the correct repair to resolve the customer concerns. NOTE: Dealers will need to follow the warranty process and obtain pre-approval using the VCAT tool. Please reference WBI/21-002. Control valves and CVT belt and pulley kits do not require pre-authorization for repairs made under warranty if they are within the dealer’s DCAL limit. 3. CVT warranty coverage can be confirmed using the warranty extensions/customer service initiatives page in Service Comm or DBS National Service History. 4. If the vehicle is no longer covered by a powertrain or parts warranty, provide owners a repair estimate for a test drive, diagnosis, and repair. If an owner requests assistance, be sure to consult goodwill guidelines available in the Assurance Products Resources Manual (APRM) section 2.2 and obtain the necessary approvals before proceeding.
NTB19-033G
Service Bulletin/Repair Instructions
INTELLIGENT CRUISE CONTROL INOPERATIVE AND AEB/FEB WARNING LIGHT ON OR RADAR OBSTRUCTION MESSAGE DISPLAYED WITH DTC C1A16 OR C2582 IF YOU CONFIRM IMPORTANT: The purpose of ACTION (on the next page) is to give you a quick idea of the work you will be performing. You MUST closely follow the entire SERVICE PROCEDURE as it contains information that is essential to successfully completing this repair. Nissan Bulletins are intended for use by qualified technicians, not 'do-it-yourselfers'. Qualified technicians are properly trained individuals who have the equipment, tools, safety instruction, and know-how to do a job properly and safely. NOTE: If you believe that a described condition may apply to a particular vehicle, DO NOT assume that it does. See your Nissan dealer to determine if this applies to your vehicle. The customer states that the ICC stopped working while driving, OR The customer states that the AEB/FEB warning light is ON, or turned ON, while driving (Figure 1), OR The message “Unavailable Front Radar Obstruction” or “Forward Driving Aids Temporarily Disabled Front Sensor Blocked See Owner's Manual” has displayed while driving (Figure 2). AND DTC C1A16, C1A16-97, C2582, or C2582-97 is the ONLY DTC stored. Figure 1 Figure 2 This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin. Forward Driving Aids Temporarily Disabled Front Sensor Blocked See Owner’s Manual
NTB19-042F
Service Bulletin/Repair Instructions
AUTOMATIC EMERGENCY BRAKING WARNING LIGHT BLINKING APPLIED SYSTEMS: Vehicles equipped with a lane camera (see Figure 1) SERVICE INFORMATION If the Automatic Emergency Braking (AEB) warning light or is blinking (but not illuminated steadily) or the customer states it is blinking, and there are no related DTCs, inspect the windshield. A blinking AEB warning light may occur under the following conditions: When contamination or foreign material adhere to the lane camera viewing window on the windshield. When driving while it is snowing or when frost forms on the lane camera viewing window on the windshield. When the lane camera viewing window on the windshield is temporarily fogged up. Figure 1 Nissan Bulletins are intended for use by qualified technicians, not 'do-it-yourselfers'. Qualified technicians are properly trained individuals who have the equipment, tools, safety instruction, and know-how to do a job properly and safely. NOTE: If you believe that a described condition may apply to a particular vehicle, DO NOT assume that it does. See your Nissan dealer to determine if this applies to your vehicle. HINT: o Refer to the applicable ESM for diagnosis if DTCs are present in the Laser/Radar, ICC/ADAS, or Lane Camera systems. o For further information: Refer to the following pages. Use the search keyword “blinking” in the ESM.
NTB19-071D
Service Bulletin/Repair Instructions
DTC B00A0-00 STORED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin. IF YOU CONFIRM DTC B00A0-00 (OCCUPANT DETECTION SENSOR UNIT) is stored, AND OCS zero point reset cannot be performed, (continued on the next page)
NTB12-103I
Service Bulletin/Repair Instructions
CVT/TCM CALIBRATION DATA “WRITE” PROCEDURE This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB10-066C
Service Bulletin/Repair Instructions
CAN COMMUNICATION CODES – DIAGNOSTIC TIPS AND GUIDELINES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB13-027D
Service Bulletin/Repair Instructions
CAN COMMUNICATION – NETWORK DIAGNOSTIC FLOW CHART This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB13-107G
Service Bulletin/Repair Instructions
VEHICLE KEY NOT DETECTED / AUTHENTICATED, ENGINE WILL NOT START This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB21-106B
Service Bulletin/Repair Instructions
DTC C1A17-49 OR C2580-49 STORED IN LASER/RADAR This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB09-081K
Service Bulletin/Repair Instructions
WINDSHIELD CRACKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB13-028I
Service Bulletin/Repair Instructions
REMOVING FOREIGN MATERIAL FROM THE WINDOW GLASS This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB17-019H
Service Bulletin/Repair Instructions
WINDOW GLASS WARRANTY INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB17-039R
Service Bulletin/Repair Instructions
DTC P17F0 OR P17F1 STORED IN THE TCM This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.
NTB19-042E
Service Bulletin/Repair Instructions
AUTOMATIC EMERGENCY BRAKING WARNING LIGHT BLINKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB23-018G
Service Bulletin/Repair Instructions
SOFTWARE UPDATE FOR INFOTAINMENT ISSUES This bulletin is no longer active. To access infotainment software updates via the Infotainment Software Update Utility: Select SPECIALTY TOOLS, and then select Infotainment Software Updates on the left side of ASIST. Please discard previous versions of NTB23-018.
NTB23-018F
Service Bulletin/Repair Instructions
SOFTWARE UPDATE FOR INFOTAINMENT ISSUES This bulletin is no longer active. To access infotainment software updates via the Infotainment Software Update Utility: Select SPECIALTY TOOLS, and then select Infotainment Software Updates on the left side of ASIST. HINT: Initially, the Infotainment Software Update Utility will be available only on the CONSULT PC version of ASIST. The Utility will be added to ASIST WEB at a later date. Please discard previous versions of NTB23-018.
NTB17-039Q
Service Bulletin/Repair Instructions
CVT JUDDER AND DTC P17F0 OR P17F1 STORED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.
NTB08-097L
Service Bulletin/Repair Instructions
DIAGNOSIS OF VEHICLE PULL (DRIFT) AND/OR STEERING WHEEL OFF-CENTER This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB23-018E
Service Bulletin/Repair Instructions
SOFTWARE UPDATE FOR INFOTAINMENT ISSUES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB23-018D
Service Bulletin/Repair Instructions
SOFTWARE UPDATE FOR INFOTAINMENT ISSUES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB23-049
Service Bulletin/Repair Instructions
12 VOLT BATTERY TESTING FOR IN-SERVICE VEHICLES SERVICE INFORMATION The following Service Information lists NNA procedural recommendations for establishing good connections while performing 12V battery testing. These recommendations are expected to promote uniformity during the connection process, therefore reducing the number of incorrect âTest with DCAâ and âReplaceâ results. HINT: If 12 volt batteries are allowed to discharge for a prolonged period of time, battery life may be drastically reduced. This condition may lead to premature battery replacement and customer dissatisfaction. IMPORTANT: ï· CPX-900 is now an accepted testing tool to use along with or in place of the DSS-5000 ï· CPX-900 operating instructions are found at: https://nissancpx900.midtronics.com/ ï· DSS-5000 operating instructions are found at: https://nissandss5000.midtronics.com/ ï· DCA-8000 is now a required testing tool to be used for all warranty replacement decisions. The DCA-8000 is also a more efficient charger than previously available, and will charge any available 12 volt lead acid battery safely and accurately as long as all precautions and inputs are made correctly. The DCA-8000 operating instructions are found at: https://nissandca8000.midtronics.com/
NTB23-053
Service Bulletin/Repair Instructions
SILICONE-BASED LUBRICANT OR GREASE CAN DAMAGE ELECTRICAL COMPONENTS SERVICE INFORMATION Do not apply Silicone-based lubricants or grease to, or around, any interior electrical components. To avoid the risk of death or severe personal injury, do not directly spray Silicone-based lubricant or grease, or inadvertently overspray Silicone-based lubricant or grease onto any interior electrical components. These types of lubricants can be detrimental to the proper operation of electrical components.
NTB17-039P
Service Bulletin/Repair Instructions
CVT JUDDER AND DTC P17F0 OR P17F1 STORED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.
NTB12-103H
Service Bulletin/Repair Instructions
CVT/TCM CALIBRATION DATA âWRITEâ PROCEDURE This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB13-107F
Service Bulletin/Repair Instructions
VEHICLE KEY NOT DETECTED / AUTHENTICATED, ENGINE WILL NOT START This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB14-012I
Service Bulletin/Repair Instructions
REMOTE ENGINE START NOT WORKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB16-003C
Service Bulletin/Repair Instructions
INTELLIGENT KEY REPLACEMENT OR SWAPPING BETWEEN VEHICLES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.
NTB23-018C
Service Bulletin/Repair Instructions
SOFTWARE UPDATE FOR INFOTAINMENT ISSUES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB03-074Q
Service Bulletin/Repair Instructions
HEADLAMP, FOG LAMP, OR REAR COMBINATION LAMP FOGGING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB12-055J
Service Bulletin/Repair Instructions
CLICKING NOISE FROM FRONT OR REAR AXLE DURING TAKE-OFF/ACCELERATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB23-018B
Service Bulletin/Repair Instructions
SOFTWARE UPDATE FOR INFOTAINMENT ISSUES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB23-018A
Service Bulletin/Repair Instructions
SOFTWARE UPDATE FOR INFOTAINMENT ISSUES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB19-042D
Service Bulletin/Repair Instructions
AUTOMATIC EMERGENCY BRAKING WARNING LIGHT BLINKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB19-071C
Service Bulletin/Repair Instructions
DTC B00A0-00 STORED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB21-106A
Service Bulletin/Repair Instructions
DTC C1A17-49 OR C2580-49 STORED IN LASER/RADAR This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB10-145B
Service Bulletin/Repair Instructions
ABS/VDC CAN DIAGNOSIS INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB23-018
Service Bulletin/Repair Instructions
SOFTWARE UPDATE FOR INFOTAINMENT ISSUES SERVICE INFORMATION When diagnosing an infotainment issue or after replacement of the AV Control Unit, it is necessary to verify the current software version of the AV Control Unit to determine if a software version update is required. Use the vehicle tables in this bulletin to determine the current software version, if the AV Control Unit requires a software version update, and which procedure to use to update the AV Control Unit. The software updates in this bulletin are to address stability improvements and âbugâ fixes. IMPORTANT: If the customer is experiencing a software related concern, refer to NTB21-038 to verify if the customer concern is a hardware or software related issue. If the concern is a software related issue, review the information in this bulletin to update the AV Control Unit as needed.
NTB09-081J
Service Bulletin/Repair Instructions
WINDSHIELD CRACKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB13-028H
Service Bulletin/Repair Instructions
REMOVING FOREIGN MATERIAL FROM THE WINDOW GLASS This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB08-097K
Service Bulletin/Repair Instructions
DIAGNOSIS OF VEHICLE PULL (DRIFT) AND/OR STEERING WHEEL OFF-CENTER This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB10-126C
Service Bulletin/Repair Instructions
WHEEL BEARING COLLISION DAMAGE This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB15-009L
Service Bulletin/Repair Instructions
NAVIGATION SYMPTOMS WHEN SD CARD IS MISSING OR WRONG CARD INSTALLED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB22-101
Service Bulletin/Repair Instructions
DRIVE SHAFT BOOT SERVICE INFORMATION SERVICE INFORMATION If a Drive Shaft (Axle Shaft) Boot on an APPLIED VEHICLE is found to be leaking grease, AND There is no abnormal noise or obvious CV Joint risk due to water intrusion and/or complete grease loss, check for REPAIR KIT-DUST BOOT (CV Joint Boot Kit) availability. ï· If there is a REPAIR KIT-DUST BOOT (CV Joint Boot Kit) available for the vehicle being repaired, do NOT replace the axle. Install a new boot kit following the procedure in the ESM. o Refer to the ESM: TRANSMISSION & DRIVELINE > FRONT AXLE > REMOVAL AND INSTALLATION > FRONT DRIVE SHAFT BOOT o If the complete axle (drive shaft) is replaced when only a new boot is required, the over-repair may be charged back to the dealer. ï· If there is NOT a REPAIR KIT-DUST BOOT (CV Joint Boot Kit) available for the vehicle being repaired, refer to the ESM for further diagnostic information. IMPORTANT: When servicing vehicles with staked axle nuts, refer to NTB21-013 to prevent Drive Shaft thread damage.
NTB22-100
Service Bulletin/Repair Instructions
3G TELEMATICS HARDWARE DEACTIVATION SERVICE INFORMATION The APPLIED VEHICLES that come equipped with a factory installed SOS switch, located near the overhead map lamp, also come equipped with a wireless communication device called a Telematics Communication Unit (TCU). AT&T discontinued its U.S. 3G network coverage on February 22, 2022. As a result, automakers that utilize AT&Tâs 3G network connection, including Nissan Group, have had connectivity services affected. NissanConnect® Services are no longer available on the APPLIED VEHICLES listed above.
NTB12-055I
Service Bulletin/Repair Instructions
CLICKING NOISE FROM FRONT OR REAR AXLE DURING TAKE-OFF/ACCELERATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB14-012H
Service Bulletin/Repair Instructions
REMOTE ENGINE START NOT WORKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB15-014C
Service Bulletin/Repair Instructions
ENHANCED DIAGNOSTIC LOGIC FOR CVT JUDDER This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB19-071B
Service Bulletin/Repair Instructions
DTC B00A0-00 STORED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB22-026
Service Bulletin/Repair Instructions
SERVICE INFORMATION FOR FUEL GAUGE INACCURATE WITH DTCS STORED IN ECM SERVICE INFORMATION If a fuel level sensor has been diagnosed as sending an incorrect level signal, and one or more of the following DTCs are stored in the ECM, do not replace the entire âFuel Level Sensor Unit, Fuel Filter and Fuel Pump Assemblyâ (fuel pump assembly). The fuel level sensor can be replaced separately. ï· P0460 (FUEL LEV SEN SLOSH) ï· P0461 (FUEL LEVEL SENSOR) ï· P0462 (FUEL LEVL SEN/CIRC) ï· P0463 (FUEL LEVL SEN/CIRC) NOTE: Warranty claims referring to fuel level issues that result in the replacement of the entire fuel pump assembly will be charged back.
NTB17-039O
Service Bulletin/Repair Instructions
CVT JUDDER AND DTC P17F0 OR P17F1 STORED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.
NTB15-049X
Service Bulletin/Repair Instructions
TELEMATICS SERVICE INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB13-027C
Service Bulletin/Repair Instructions
CAN COMMUNICATION â NETWORK DIAGNOSTIC FLOW CHART This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB13-097J
Service Bulletin/Repair Instructions
EVAP LEAK DTC P0442, P0455, P0456 INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB17-082E
Service Bulletin/Repair Instructions
DTC P0456 CAUSED BY EVAP LEAK AT VENT CONTROL VALVE O-RING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB17-039N
Service Bulletin/Repair Instructions
PATHFINDER, ALTIMA, MAXIMA, MURANO AND QUEST; CVT JUDDER AND DTC P17F0 OR P17F1 STORED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.
NTB17-045C
Service Bulletin/Repair Instructions
CLEANING FRONT OR REAR COMBINATION LAMP ASSEMBLIES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB99-001F
Service Bulletin/Repair Instructions
STRUT AND SHOCK ABSORBER REPLACEMENT GUIDELINES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB21-106
Service Bulletin/Repair Instructions
DTC C1A17-49 OR C2580-49 STORED IN LASER/RADAR SERVICE INFORMATION If DTC C1A17-49 or C2580-49 is stored in LASER/RADAR in the âPASTâ column: ï· Erase the DTC. ï· DO NOT replace any parts. If DTC C1A17-49 or C2580-49 is stored in LASER/RADAR in the "CURRENT" column, refer to the applicable ESM for instructions.
NTB18-055E
Service Bulletin/Repair Instructions
CVT FLUID LEVEL QUICK CHECK GAUGE This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB16-017C
Service Bulletin/Repair Instructions
MOONROOF ADJUSTMENT AND REPAIRS This bulletin has been amended. See Amendment History on the last page. Please discard previous versions of this bulletin.
NTB19-059C
Service Bulletin/Repair Instructions
MOONROOF RATTLE This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB12-055H
Service Bulletin/Repair Instructions
CLICKING NOISE FROM FRONT OR REAR AXLE DURING TAKE-OFF/ACCELERATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB15-077D
Service Bulletin/Repair Instructions
SIGNAL TECH-II INTELLIGENT KEY BATTERY TEST AND SIGNAL CHECK This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB16-028D
Service Bulletin/Repair Instructions
INTELLIGENT KEY BUTTONS INOPERATIVE BUT REQUEST SWITCHES WORK This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
Altima Maxima Lo
Service Bulletin/Repair Instructions
Rear Lower Suspension Link Warranty Extension Dealer Notification In October 2019, Nissan launched a Voluntary Service Campaign (P9324) on MY2013 Nissan Altima vehicles registered in high road-salt-usage states (Connecticut, Delaware, Iowa, Illinois, Indiana, Kentucky, Massachusetts, Maine, Maryland, Michigan, Minnesota, Missouri, New Hampshire, New Jersey, New York, Ohio, Pennsylvania, Rhode Island, Vermont, Virginia, Washington D.C., West Virginia and Wisconsin). In the interest of customer satisfaction, Nissan is providing a warranty extension to certain MY2013 Nissan Altima vehicles that were not included in P9324 and certain MY2014-2018 Nissan Altima and MY2016-2018 Nissan Maxima vehicles in all states. On some affected vehicles, one of the rear lower suspension links may corrode and separate at the bushing joint area. Customers may notice a knocking or rattling noise from the rear of the vehicle or observe wheel misalignment on the rear wheel(s) if the link separates. Owners of eligible vehicles will receive a notification indicating their eligibility for the following: â¢Warranty extension for the rear lower suspension links of 84 months and unlimited miles to their current 36 month/36,000 mile New Vehicle Limited Warranty for a total of 120 months warranty coverage (without regard to mileage). â¢This warranty extension will allow for a one-time replacement of the rear lower suspension links with new parts and a four-wheel alignment if parts are cracked or broken. Voluntary Service Campaign (P9324) on MY2013 Nissan Altima vehicles registered in high road-salt-usage states will continue. What Dealers Should Do: 1.Verify if vehicles are eligible for this Warranty Extension using the warranty extension page of Service Comm. 2.Dealers should remedy any eligible vehicles subject to this warranty extension to ensure customer satisfaction using Technical Field Bulletin NTB21-045.
NTB21-045
Service Bulletin/Repair Instructions
2013-2018 ALTIMA AND 2016-2018 MAXIMA; REAR SUSPENSION LOWER LINK IF YOU CONFIRM The customer experiences a knocking or rattling noise from the rear of the vehicle, Or The rear wheel and tire assemblies have a large amount of positive camber. ACTION Replace both rear lower links.
NTB16-018D
Service Bulletin/Repair Instructions
MIL ON WITH P0603 STORED FOR ECM BACK UP CIRCUIT This bulletin has been amended. See AMENDMENT HISTORY on page 3. Please discard previous versions of this bulletin.
NTB15-049W
Service Bulletin/Repair Instructions
TELEMATICS SERVICE INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB15-009K
Service Bulletin/Repair Instructions
NAVIGATION SYMPTOMS WHEN SD CARD IS MISSING OR WRONG CARD INSTALLED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB15-001E
Service Bulletin/Repair Instructions
AV CONTROL UNIT REPLACEMENT This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB17-081A
Service Bulletin/Repair Instructions
THEFT ALARM SOUNDS WHEN VEHICLE IS LOCKED, UNLOCKED, OR DOOR/TRUNK OPENED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB15-077C
Service Bulletin/Repair Instructions
NISSAN; SIGNAL TECH-II INTELLIGENT KEY BATTERY TEST AND SIGNAL CHECK This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB16-002A
Service Bulletin/Repair Instructions
NISSAN; REPLACING LOST INTELLIGENT KEYS FOR APPLICABLE 2016 MODEL YEAR VEHICLES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB15-052A
Service Bulletin/Repair Instructions
2016 NISSAN; REGISTRATION OF NEW I-KEYS WHEN ORIGINALS ARE MISSING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.
NTB16-028C
Service Bulletin/Repair Instructions
INTELLIGENT KEY BUTTONS INOPERATIVE BUT REQUEST SWITCHES WORK This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB15-099C
Service Bulletin/Repair Instructions
SERVICE INFORMATION FOR DTCS C1A12 AND C1A16 This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.
NTB16-093A
Service Bulletin/Repair Instructions
NAVIGATION FREEZES, BLUETOOTH CALL VOLUME FLUCTUATES, BUTTON ILLUMINATION DIM, OR USB DEVICE NOT RECOGNIZED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB17-014A
Service Bulletin/Repair Instructions
BLUETOOTH, USB, AND AUX FUNCTION DIAGNOSTIC TOOL This bulletin has been amended. See AMENDMENT HISTORY on page 3. Please discard previous versions of this bulletin.
NTB18-017D
Service Bulletin/Repair Instructions
SERVICE INFORMATION FOR DTCS B2EF0 AND B130C This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB19-071A
Service Bulletin/Repair Instructions
DTC B00A0-00 STORED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB09-140C
Service Bulletin/Repair Instructions
CVT OIL LEAK DIAGNOSIS USING FLUORESCENT DYE This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB15-013f
Service Bulletin/Repair Instructions
NISSAN; PROCEDURE TO CLEAN CVT TRANSMISSION FLUID COOLERS This bulletin is no longer active. Please discard previous versions of NTB15-013. Refer to the ESM for the fluid cooler cleaning procedure.
NTB17-039m
Service Bulletin/Repair Instructions
PATHFINDER, ALTIMA, MAXIMA, MURANO AND QUEST; CVT JUDDER AND DTC P17F0 OR P17F1 STORED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.
NTB99-001e
Service Bulletin/Repair Instructions
STRUT AND SHOCK ABSORBER REPLACEMENT GUIDELINES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB19-042b
Service Bulletin/Repair Instructions
AEB WARNING LIGHT BLINKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB16-008a
Service Bulletin/Repair Instructions
NISSAN; THEFT ALARM TRIGGER HISTORY FUNCTION This bulletin is no longer active. Please discard previous versions of NTB16-008.
NTB15-049v
Service Bulletin/Repair Instructions
TELEMATICS SERVICE INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB17-039l
Service Bulletin/Repair Instructions
PATHFINDER, ALTIMA, MAXIMA, MURANO AND QUEST; CVT JUDDER AND DTC P17F0 OR P17F1 STORED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.
NTB19-079a
Service Bulletin/Repair Instructions
REAR PILLAR MOLDING REPLACEMENT This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB16-017b
Service Bulletin/Repair Instructions
MOONROOF ADJUSTMENT AND REPAIRS This bulletin has been amended. See Amendment History on the last page. Please discard previous versions of this bulletin.
NTB19-059b
Service Bulletin/Repair Instructions
MOONROOF RATTLE This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB19-042a
Service Bulletin/Repair Instructions
AEB WARNING LIGHT BLINKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB17-039k
Service Bulletin/Repair Instructions
PATHFINDER, ALTIMA, MAXIMA, MURANO AND QUEST; CVT JUDDER AND DTC P17F0 OR P17F1 STORED IF YOU CONFIRM The customer reports a transmission judder (shake, shudder, single or multiple bumps or vibration), AND One of these DTCs is stored: ï· P17F0 (CVT_JUDDER (T/M INSPECTION)) ï· P17F1 (CVT_JUDDER (C/U INSPECTION)) NOTE: ï If a transmission judder (as described above) is not reported, this bulletin does not apply. ï If either P17F0 or P17F1 are not stored, this bulletin does not apply. ï If any DTCs are stored other than P17F0 or P17F1, this bulletin does not apply. ï NTB15-014, Enhanced Diagnostic Logic For CVT Judder, has reprogramming instructions that may apply. ACTION ï· Refer to the Repair Flow Chart on page 2 for CVT repair. CAUTION: Always handle the CVT and component assemblies carefully and with the appropriate lifting tools.
NTB15-049u
Service Bulletin/Repair Instructions
TELEMATICS SERVICE INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB19-059a
Service Bulletin/Repair Instructions
MOONROOF RATTLE This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB17-039j
Service Bulletin/Repair Instructions
PATHFINDER, ALTIMA, MAXIMA, MURANO AND QUEST; CVT JUDDER AND DTC P17F0 OR P17F1 STORED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.
NTB18-055d
Service Bulletin/Repair Instructions
CVT FLUID LEVEL QUICK CHECK GAUGE This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB17-039i
Service Bulletin/Repair Instructions
PATHFINDER, ALTIMA, MAXIMA, MURANO AND QUEST; CVT JUDDER AND DTC P17F0 OR P17F1 STORED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.
NTB15-049t
Service Bulletin/Repair Instructions
TELEMATICS SERVICE INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB18-017c
Service Bulletin/Repair Instructions
SERVICE INFORMATION FOR DTCS B2EF0 AND B130C This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB12-055g
Service Bulletin/Repair Instructions
CLICKING NOISE FROM FRONT OR REAR AXLE DURING TAKE-OFF/ACCELERATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB19-045b
Service Bulletin/Repair Instructions
MIL ON WITH DTC P0087, P0101, P0448, OR P2008, VEHICLES REGISTERED OUTSIDE OF CALIFORNIA This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB19-115a
Service Bulletin/Repair Instructions
VOLUNTARY EMISSIONS SERVICE CAMPAIGN VEHICLES REGISTERED IN CALIFORNIA; ENGINE CONTROL MODULE INTRODUCTION Nissan is conducting this voluntary emissions service campaign on certain specific model year Nissan vehicles (see APPLIED VEHICLES) registered in the state of California. The engine control module (ECM) will be inspected, and reprogrammed if applicable. This service will be performed at no charge to the customer for parts or labor. IDENTIFICATION NUMBER Nissan has assigned identification numbers P9328, P9343, P9345, P9347, and P9349 to this campaign. The correct number must appear on all communication and documentation of any nature dealing with this campaign. DEALER RESPONSIBILITY Dealers are to repair vehicles falling within range of this campaign that enter the service department. This includes vehicles purchased from private parties, vehicles presented by transient (tourists) owners, and vehicles in a dealerâs inventory.
P9328_P9343_P934
Service Bulletin/Repair Instructions
Engine Control Module (ECM) Reprogram California Voluntary Emissions Service Campaign ***** Campaign Summary***** Nissan is conducting a Voluntary Emissions Service Campaign on approximately 104,221 specific Nissan vehicles identified in Service Comm and currently registered to owners in the state of California to reprogram the Engine Control Module (ECM) in the event that a permanent diagnostic trouble code (P-DTC) for P0448, P0101, P2008, or P0087 is recorded in the ECM. Due to calibration errors on the affected vehicles, the ECM may improperly store a permanent diagnostic trouble code (P-DTC) even though the emissions on-board diagnostic system is functioning properly. As of July 1, 2019 the State of California has implemented a revised Inspection Maintenance (I/M) or âSmog Checkâ test program. Without the software update, the subject vehicles may not pass this Smog Check test in those areas of California where such testing is required under state law. This incident has no effect on the safety, performance, drivability, or fuel consumption of the applicable vehicles. ***** What Dealers Should Do ***** 1. Verify if vehicles are affected by this Voluntary Emissions Service Campaign using Service Comm or DBS National Service History â Open Campaigns I.D. ï· P9328 â Affected Model Year 2015 ï· P9343 â Affected Model Year 2016 ï· P9345 â Affected Model Year 2017 ï· P9347 â Affected Model Year 2018 ï· P9349 â Affected Model Year 2019 2. Dealers should remedy any affected vehicles in dealer new or pre-owned inventory to ensure customer satisfaction.
NTB19-115
Service Bulletin/Repair Instructions
VOLUNTARY EMISSIONS SERVICE CAMPAIGN VEHICLES REGISTERED IN CALIFORNIA; ENGINE CONTROL MODULE INTRODUCTION Nissan is conducting this voluntary emissions service campaign on certain specific model year Nissan vehicles (see APPLIED VEHICLES) registered in the state of California. The engine control module (ECM) will be inspected, and reprogrammed if applicable. This service will be performed at no charge to the customer for parts or labor. IDENTIFICATION NUMBER Nissan has assigned identification numbers P9328, P9343, P9435, P9347, and P9349 to this campaign. The correct number must appear on all communication and documentation of any nature dealing with this campaign. DEALER RESPONSIBILITY Dealers are to repair vehicles falling within range of this campaign that enter the service department. This includes vehicles purchased from private parties, vehicles presented by transient (tourists) owners, and vehicles in a dealerâs inventory.
NTB15-013e
Service Bulletin/Repair Instructions
NISSAN; PROCEDURE TO CLEAN CVT TRANSMISSION FLUID COOLERS This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB17-039h
Service Bulletin/Repair Instructions
PATHFINDER, ALTIMA, MAXIMA, MURANO AND QUEST; CVT JUDDER AND DTC P17F0 OR P17F1 STORED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.
NTB16-085b
Service Bulletin/Repair Instructions
ENHANCED DIAGNOSTIC LOGIC FOR CVT This bulletin has been superseded by NTB17-039. Please discard previous versions of this bulletin.
NTB19-079
Service Bulletin/Repair Instructions
REAR PILLAR MOLDING REPLACEMENT SERVICE INFORMATION If the rear pillar molding needs to be replaced for any reason, refer to the SERVICE PROCEDURE starting on the next page.
NTB17-039g
Service Bulletin/Repair Instructions
PATHFINDER, ALTIMA, MAXIMA, MURANO AND QUEST; CVT JUDDER AND DTC P17F0 OR P17F1 STORED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.
NTB19-052a
Service Bulletin/Repair Instructions
2016-2018 MAXIMA; LOW POWER / STOP LAMPS STAY ON This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB19-045a
Service Bulletin/Repair Instructions
MIL ON WITH DTC P0087, P0101, P0448, OR P2008 This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB19-072
Service Bulletin/Repair Instructions
TRANSMISSION RANGE SWITCH SERVICE INFORMATION SERVICE INFORMATION The transmission range switch of the APPLIED VEHICLES listed above is now available as a separate service part. If the transmission range switch of an APPLIED VEHICLE is being replaced for any reason, it must be adjusted after its replacement. ï· Refer to SERVICE PROCEDURE on page 3 for transmission range switch removal, installation, and adjustment.
NTB19-071
Service Bulletin/Repair Instructions
DTC B00A0-00 STORED IF YOU CONFIRM DTC B00A0-00 (OCCUPANT DETECTION SENSOR UNIT) is stored And OCS zero point reset cannot be performed (continued on the next page) And The following screen displays: ACTION 1. Check the Occupant Classification System (OCS) control unit using the ODS Analysis tool software. ï· Refer to SERVICE PROCEDURE on page 5. HINT: âOCSâ may also be referred to as âODSâ. 2. Perform â75-zero RESETâ.
NTB14-012e
Service Bulletin/Repair Instructions
REMOTE ENGINE START NOT WORKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB16-017a
Service Bulletin/Repair Instructions
MOONROOF ADJUSTMENT AND REPAIRS This bulletin has been amended. See Amendment History on the last page. Please discard previous versions of this bulletin.
NTB19-059
Service Bulletin/Repair Instructions
MOONROOF RATTLE IF YOU CONFIRM Customer reports ï· A rattle noise from the moonroof when driving with the moonroof open OR ï· An abnormal noise when opening/closing the Moonroof. ACTION 1. Inspect for a broken anti-rattle clip located on the left and right rear link assembly. 2. Replace anti-rattle clip(s) as needed.
NTB19-052
Service Bulletin/Repair Instructions
2016-2018 MAXIMA; LOW POWER / STOP LAMPS STAY ON IF YOU CONFIRM The customer reports that Intermittently there is low power when accelerating, And/or The stop lamps (brake lights) stay ON after releasing the brake pedal, with the ignition ON or OFF. ACTION Install the jumper harness from the Parts Information section using the Service Procedure starting on page 2.
NTB15-049s
Service Bulletin/Repair Instructions
TELEMATICS SERVICE INFORMATION This bulletin applies only to vehicles equipped with a Telematics Communication Unit (TCU). This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB19-045
Service Bulletin/Repair Instructions
MIL ON WITH DTC P0087, P0101, P0448, OR P2008 IF YOU CONFIRM An applied vehicle has a stored DTC shown in Table A on the next page, AND The ECM part number is shown in Table B, starting on page 3. ACTION First, perform the appropriate diagnostic procedure for the stored code to repair the vehicle according to the Electronic Service Manual (ESM), AND Reprogram the ECM after performing the diagnosis and repair.
NTB19-044
Service Bulletin/Repair Instructions
ENGINE SUPPORT TOOLS SERVICE INFORMATION A new Engine Support Tool and Engine Support Bracket are now available to allow the CVT to be removed from the Applied Vehicles without having to remove the engine. The procedure in this bulletin is different from the procedure currently in the Electronic Service Manual (ESM), which will be updated with this information at a later date. Please refer to the SERVICE PROCEDURE on page 2 to use these new tools.
NTB14-060c
Service Bulletin/Repair Instructions
ABNORMAL NOISE FROM FRONT ENGINE MOUNT SERVICE INFORMATION A two-piece design front engine mount is currently being used for the Applied Vehicles listed. A single thunk noise may be heard during the first few accelerations of the day from this type of mount, and is considered normal operation. The mount has also been designed with built-in free play that is normal. Under normal driving conditions: - A thunk noise may be heard during the first few accelerations of the day, And - Does not occur again, or at any other time. DO NOT REPLACE THE MOUNT: - If it has free play or a ?single event? thunk sound during the first few accelerations of the day. This is considered a normal characteristic of this type of engine mount. - Allowable free play (vertical movement) is 5 mm. - If a shift shock condition is present when shifting from Park into gear or between any combination of gears. This condition is due to transmission line pressure and not movement of the mount. - If a whistle type noise is heard. This is caused by a disconnected vacuum line. NOTE: Refer to the appropriate section of the Electronic Service Manual (ESM) related to transaxles for further diagnostic information on shift shock. Warranty claims for front engine mount replacement due to a whistle noise or a mount that has 5 mm or less free play will be denied.
NTB18-055c
Service Bulletin/Repair Instructions
CVT FLUID LEVEL QUICK CHECK GAUGE This bulletin applies only to vehicles equipped with a Continuously Variable Transmission (CVT). This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB19-042
Service Bulletin/Repair Instructions
AEB WARNING LIGHT BLINKING This bulletin applies only to vehicles equipped with a lane camera. SERVICE INFORMATION If the AEB warning light is blinking (but not illuminated steadily) or the customer states it is blinking, and there are no related DTCs, inspect the windshield. A blinking AEB warning light may occur under the following conditions: - When contamination or foreign material adhere to the lane camera viewing window on the windshield - When driving while it is snowing or when frost forms on the lane camera viewing window on the windshield - When the lane camera viewing window on the windshield is temporarily fogged up NOTE: - If DTCs are present in any of the following related systems: - Laser/Radar, - ICC/ADAS, or - Lane Camera, Refer to the related Electronic Service Manual (ESM) for diagnosis. - Refer to the following pages for further information.
NTB19-030
Service Bulletin/Repair Instructions
2016-2018 NISSAN; MIL ON WITH DTC P0171, P0174, P2097, AND/OR P2099 This bulletin applies to Altima vehicles equipped with VQ35 engine only. IF YOU CONFIRM The MIL is ON with one or more of the following Air/Fuel (A/F) Sensor DTCs stored: - P0171 (Fuel Injection System Function) - P0174 (Fuel Injection System Function) - P2097 (A/F SENSOR 1) - P2099 (A/F SENSOR 1) ACTION 1. Perform the appropriate diagnostic procedure outlined in the Electronic Service Manual (ESM). 2. Refer to Table A on page 2 and page 3 to confirm if Electronic Control Module (ECM) reprogramming is needed.
NTB12-100b
Service Bulletin/Repair Instructions
CVT / TCM CALIBRATION DATA ?WRITE? PROCEDURE This bulletin applies only to vehicles equipped with a Continuously Variable Transmission (CVT). This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB12-103g
Service Bulletin/Repair Instructions
CVT / TCM CALIBRATION DATA ?WRITE? PROCEDURE This bulletin applies only to vehicles equipped with a Continuously Variable Transmission (CVT). This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB18-055b
Service Bulletin/Repair Instructions
CVT FLUID LEVEL QUICK CHECK GAUGE This bulletin applies only to vehicles equipped with a Continuously Variable Transmission (CVT). This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.
NTB16-028b
Service Bulletin/Repair Instructions
INTELLIGENT KEY BUTTONS INOPERATIVE BUT REQUEST SWITCHES WORK This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB15-009j
Service Bulletin/Repair Instructions
NAVIGATION SYMPTOMS WHEN SD CARD IS MISSINGOR WRONG CARD INSTALLED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB13-097g
Service Bulletin/Repair Instructions
ALL MODEL YEAR 2012 AND NEWER NISSAN VEHICLES; EVAP LEAK DTC P0442, P0455, P0456 INFORMATION This bulletin does NOT apply to LEAF vehicles and Titan XD vehicles with V8 diesel engine. This bulletin has been amended. See Amendment History on the last page. Please discard previous versions of this bulletin.
NTB15-049r
Service Bulletin/Repair Instructions
TELEMATICS SERVICE INFORMATION This bulletin applies only to vehicles equipped with a Telematics Communication Unit (TCU). This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB17-082b
Service Bulletin/Repair Instructions
NISSAN; DTC P0456 CAUSED BY EVAP LEAK AT VENT CONTROL VALVE O-RING This bulletin does NOT apply to LEAF vehicles and Titan XD vehicles with V8 diesel engine. This bulletin has been amended. See Amendment History on the last page. Please discard previous versions of this bulletin.
NTB17-030a
Service Bulletin/Repair Instructions
NISSAN; FUEL TANK IS EXTREMELY DIFFICULT TO FILL This bulletin applies to Titan XD vehicles with a gas engine. The update below was sent out to Regions and Dealers in August of this year. We are re-circulating this update to make regional and dealer personnel aware that we are re-notifying customers at this time.
Revision 1-NEVAP
Service Bulletin/Repair Instructions
OBD II EVAP Tube Warranty Enhancement The update below was sent out to Regions and Dealers in August of this year. We are re-circulating this update to make regional and dealer personnel aware that we are re-notifying customers at this time.
NTB12-103f
Service Bulletin/Repair Instructions
CVT / TCM CALIBRATION DATA ?WRITE? PROCEDURE This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB18-075
Service Bulletin/Repair Instructions
2016-2017 MAXIMA; FRONT SEAT FINISHER LOOSE IF YOU CONFIRM The seat cushion outer finisher is loose and will not stay snapped into place. ACTION Replace the affected ?seat cushion outer finisher? and the ?seat cushion inner finisher? with those listed in the Parts Information.
NTB18-055a
Service Bulletin/Repair Instructions
CVT FLUID LEVEL QUICK CHECK GAUGE This bulletin applies only to vehicles equipped with a CVT (Continuously Variable Transmission). This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB15-077b
Service Bulletin/Repair Instructions
NISSAN; SIGNAL TECH-II INTELLIGENT KEY BATTERY TEST AND SIGNAL CHECK This bulletin has been amended. See Amendment History on the last page. Please discard previous versions of this bulletin.
NTB17-040b
Service Bulletin/Repair Instructions
REVISED WHEEL ALIGNMENT SPECIFICATIONS This bulletin has been amended to add 2018-2019 Kicks. Please discard previous versions of this bulletin.
NTB15-049q
Service Bulletin/Repair Instructions
TELEMATICS SERVICE INFORMATION This bulletin applies only to vehicles equipped with a Telematics Communication Unit (TCU). This bulletin has been amended to add a Required Actions by Model and Year table on page 2, a Check OFF Sheet on page 21 and to reorganize the information throughout. It is necessary for you to read this revised procedure to properly perform this Service Information. Please discard previous versions of this bulletin.
NTB13-077d
Service Bulletin/Repair Instructions
CVT FLUID LEVEL CHECK SERVICE INFORMATION This bulletin applies only to vehicles equipped with a Continuously Variable Transmission (CVT). This bulletin has been amended. The APPLIED VEHICLES and SERVICE INFORMATION sections have been revised. No other changes have been made. Please discard all previous versions of this bulletin.
NTB15-049p
Service Bulletin/Repair Instructions
TELEMATICS SERVICE INFORMATION This bulletin only applies to vehicles equipped with a Telematics Communication Unit (TCU). This bulletin has been amended. Changes have been made to page 10 for 2018 Armada. Please discard previous versions of this bulletin.
NTB18-055
Service Bulletin/Repair Instructions
CVT FLUID LEVEL QUICK CHECK GAUGE This bulletin applies only to vehicles equipped with a Continuously Variable Transmission (CVT). SERVICE INFORMATION Special tool CVT8 Oil Level Quick Check Gauge (J-51155) is now available. Each dealer has been shipped one of these tools. Additional tools can be obtained from Tech?Mate at 1-800-662-2001. Refer to the SERVICE PROCEDURE on the next page to determine how to perform a CVT fluid quick level check.
NTB18-017b
Service Bulletin/Repair Instructions
NISSAN; SERVICE INFORMATION FOR DTCS B2EF0 AND B130C This bulletin only applies to vehicles equipped with a Telematics Communication Unit (TCU). This bulletin has been amended. APPLIED VEHICLES has been updated. On page 2, the procedural steps under DTC B130C have been revised. Discard all previous versions of this bulletin.
NTB15-009i
Service Bulletin/Repair Instructions
NAVIGATION SYMPTOMS WHEN SD CARD IS MISSING OR WRONG CARD INSTALLED This bulletin has been amended. The tables on pages 6 - 9 have been revised. No other changes have been made. Please discard previous versions of this bulletin.
NTB03-074m
Service Bulletin/Repair Instructions
FOG LAMP AND/OR HEADLAMP FOGGING This bulletin has been amended to add Fog Lamps and modify one step in the flow chart on page 3. No other changes have been made. Please discard previous versions of this bulletin.
NTB16-018c
Service Bulletin/Repair Instructions
MIL ON WITH P0603 STORED FOR ECM BACK UP CIRCUIT This bulletin does NOT apply to Titan equipped with Cummins V8 Diesel engine. This bulletin has been amended to add a NOTE in the Applied Vehicles. No other changes have been made. Please discard previous versions of this bulletin.
NTB15-009h
Service Bulletin/Repair Instructions
NAVIGATION SYMPTOMS WHEN SD CARD IS MISSING OR WRONG CARD INSTALLED This bulletin has been amended. The tables on page 5 and 6 have been revised. No other changes have been made. Please discard previous versions of this bulletin.
NTB13-107b
Service Bulletin/Repair Instructions
INTELLIGENT KEY NOT DETECTED / ENGINE WILL NOT START This bulletin has been amended to update the Applied Vehicles. No other changes were made. Please discard previous versions of this bulletin.
NTB18-017a
Service Bulletin/Repair Instructions
NISSAN; SERVICE INFORMATION FOR DTCS B2EF0 AND B130C This bulletin applies only to vehicles equipped with Telematics. This bulletin has been amended. APPLIED VEHICLES was updated and a DTC listed in the SERVICE INFORMATION was corrected. No other changes have been made. Discard all previous versions of this bulletin.
NTB11-044c
Service Bulletin/Repair Instructions
WHEEL BALANCING SERVICE INFORMATION This bulletin has been amended. The publication date has been revised to include the latest models and model years. No other changes have been made. Please discard previous versions of this bulletin.
NTB17-039f
Service Bulletin/Repair Instructions
PATHFINDER, ALTIMA, MAXIMA, MURANO AND QUEST; CVT JUDDER AND DTC P17F0 OR P17F1 STORED This bulletin applies only to vehicles equipped with a V6 engine. This bulletin has been amended to change the Claims Information on page 103. Please discard previous versions of this bulletin.
NTB15-009g
Service Bulletin/Repair Instructions
NAVIGATION SYMPTOMS WHEN SD CARD IS MISSING OR WRONG CARD INSTALLED This bulletin has been amended. The Applied Vehicles section has been revised, and changes have been made to the table beginning on page 5. No other changes have been made. Please discard previous versions of this bulletin.
NTB17-039e
Service Bulletin/Repair Instructions
PATHFINDER, ALTIMA, MAXIMA, MURANO AND QUEST; CVT JUDDER AND DTC P17F0 OR P17F1 STORED This bulletin applies only to vehicles equipped with a V6 engine. This bulletin has been amended to add Quest to Applied Vehicles and information related to Quest on pages 25, 100, 102, 103 and 105. Please discard previous versions of this bulletin. IMPORTANT: You must read the entire bulletin to properly perform this repair.
NTB18-017
Service Bulletin/Repair Instructions
NISSAN; SERVICE INFORMATION FOR DTCS B2EF0 AND B130C This bulletin applies only to vehicles equipped with Telematics. SERVICE INFORMATION Diagnostic information in the Electronic Service Manuals (ESM) for the following DTCs may be missing or incorrect: -B2EF0 ? INTERNAL BATTERY (CIRC VOLT BELOW THRESHOLD) -B130C ? TCU (Telematics Control Unit) PAIRING ERROR If one of these DTCs is stored, follow the steps listed below along with the Electronic Service Manual (ESM) to compete the required repairs. DTC B2FE0 ? INTERNAL BATTERY (CIRC VOLT BELOW THRESHOLD): 1. Start the engine and let it idle for 30 minutes (to allow charging of the TCU internal battery). -2018 LEAF only: Put the vehicle in Ready to Drive mode (depress the brake pedal and depress the power [?ignition?] switch) for 30 minutes. 2. Verify the DTC can be erased. 3. If the DTC will not erase, replace the TCU. DTC B130C: 1. Collect all keys, and then re-register them to the vehicle. 2. Verify the DTC can be erased. 3. If the DTC will not erase, replace the TCU. NOTE: The related Electronic Service Manuals (ESM) will be updated at a later date. CLAIMS INFORMATION Refer to the current Nissan Warranty Flat Rate Manual and submit a claim for the repairs performed.
NTB15-049o
Service Bulletin/Repair Instructions
TELEMATICS SERVICE INFORMATION This bulletin applies only to vehicles equipped with a Telematics Communication Unit (TCU). This bulletin has been amended. Changes have been made throughout. It is necessary to read the revised procedure(s) in entirety to properly perform the action(s). Please discard previous versions of this bulletin.
NTB15-049n
Service Bulletin/Repair Instructions
TELEMATICS SERVICE INFORMATION This bulletin applies to vehicles equipped with a TCU (Telematics Communication Unit). This bulletin has been amended. A correction was made to the Service Procedure on page 23. No other changes were made. Please discard previous versions of this bulletin.
NTB17-040a
Service Bulletin/Repair Instructions
REVISED WHEEL ALIGNMENT SPECIFICATIONS This bulletin has been amended to add 2018 Versa Sedan and 2018 Versa Note. No other changes have been made. Please discard previous versions of this bulletin.
NTB15-049m
Service Bulletin/Repair Instructions
TELEMATICS SERVICE INFORMATION This bulletin applies to vehicles that are equipped with a wireless communication device called a Telematics Communication Unit (TCU). This bulletin has been amended. Changes have been made throughout. You must read the entire bulletin to understand all the changed information. Please discard previous versions of this bulletin.
NTB17-039c
Service Bulletin/Repair Instructions
PATHFINDER, ALTIMA, MAXIMA, MURANO; CVT JUDDER AND DTC P17F0 OR P17F1 STORED This bulletin applies to Altima vehicles equipped with a V6 engine only. This bulletin has changed. You must read the entire bulletin to properly perform this repair. Please discard previous versions of this bulletin.
NTB17-039d
Service Bulletin/Repair Instructions
PATHFINDER, ALTIMA, MAXIMA, MURANO; CVT JUDDER AND DTC P17F0 OR P17F1 STORED This bulletin applies to Altima vehicles equipped with a V6 engine only. This bulletin has been amended to change the parts table information on page 101. Please discard previous versions of this bulletin. IMPORTANT: You must read the entire bulletin to properly perform this repair.
NTB15-049L
Service Bulletin/Repair Instructions
TELEMATICS SERVICE INFORMATION This bulletin applies to vehicles equipped with a Telematics Communication Unit (TCU). This bulletin has been amended. Information for several 2018 models has been added. No other changes have been made. Please discard previous versions of this bulletin.
NTB17-107
Service Bulletin/Repair Instructions
2016-2017 MAXIMA AND ALTIMA; POP/CLUNK NOISE FROM REAR WHEN DRIVING OVER BUMPS This bulletin applies to SR trim level Altima vehicles. IF YOU CONFIRM A pop or clunk noise from the rear of the vehicle, especially when driving over bumps, AND The rear suspention connecting rod nuts are found to be loose on the left and/or right side. ACTION Replace the connecting rod and nuts on the left and/or right side with the ones listed in Parts Information.
NTB11-044b
Service Bulletin/Repair Instructions
WHEEL BALANCING SERVICE INFORMATION This bulletin has been amended. The publication date has been revised to include the latest models and model years. No other changes have been made. Please discard previous versions of this bulletin.
NTB17-017b
Service Bulletin/Repair Instructions
2016-2017 MAXIMA; NOISE HEARD WHEN LEANING BACK IN A FRONT SEAT This bulletin has been amended. Nissan brand grease is now specified in Step 13 of the SERVICE PROCEDURE and listed in the PARTS INFORMATION. No other changes have been made. Discard all previous versions of this bulletin.
NTB17-017a
Service Bulletin/Repair Instructions
2016-2017 MAXIMA; NOISE HEARD WHEN LEANING BACK IN A FRONT SEAT This bulletin has been amended throughout. Discard previous versions of this bulletin.
NTB17-033b
Service Bulletin/Repair Instructions
2016 MAXIMA; OCCUPANT CLASSIFICATION SYSTEM RETROFIT This bulletin has been amended. Pages 16 and 18 have been revised. No other changes have been made. Please discard all previous versions of this bulletin.
NTB15-049k
Service Bulletin/Repair Instructions
TELEMATICS SERVICE INFORMATION This bulletin has been amended. The Applied Vehicles section has been revised and TCU Configuration section has been added. No other changes have been made. Please discard previous versions of this bulletin.
NTB13-077c
Service Bulletin/Repair Instructions
CVT FLUID LEVEL CHECK SERVICE INFORMATION This bulletin applies only to vehicles equipped with a Continuously Variable Transmission (CVT). This bulletin has been amended. The APPLIED VEHICLES section has been revised. No other changes have been made. Please discard all previous versions of this bulletin.
NTB17-082a
Service Bulletin/Repair Instructions
NISSAN; DTC P0456 CAUSED BY EVAP LEAK AT VENT CONTROL VALVE O-RING This bulletin has been amended. The APPLIED VEHICLES and CLAIMS INFORMATION sections have been revised. No other changes have been made. Please discard previous versions of this bulletin.
NTB17-008b
Service Bulletin/Repair Instructions
NISSAN; OIL LEAKING AROUND VALVE TIMING CONTROL SOLENOID VALVE This bulletin applies only to Maxima, Quest, Altima Coupe, Altima Sedan, Pathfinder and Murano vehicles with a 6-cylinder engine and Titan/Titan XD vehicles with a V8 gasoline engine. This bulletin has been amended. The PARTS INFORMATION section has been revised. No other changes have been made. Please discard previous versions of this bulletin.
NTB17-033a
Service Bulletin/Repair Instructions
2016 MAXIMA; OCCUPANT CLASSIFICATION SYSTEM RETROFIT This bulletin has been amended. The CLAIMS INFORMATION section has been revised. No other changes have been made. Please discard all previous versions of this bulletin.
NTB15-009f
Service Bulletin/Repair Instructions
NAVIGATION SYMPTOMS WHEN SD CARD IS MISSING OR WRONG CARD INSTALLED This bulletin has been amended. Changes have been made to the parts table on page 5 under 17.5MY Murano. No other changes were made. Please discard previous versions of this bulletin.
NTB14-060b
Service Bulletin/Repair Instructions
THUNK SOUND ON FIRST FEW ACCELERATIONS OF THE DAY This bulletin applies only to Altima, Murano, and Pathfinder vehicles equipped with 6-cylinder engine. This bulletin has been amended. Changes have been made throughout. Please discard previous versions of this bulletin.
NTB15-001d
Service Bulletin/Repair Instructions
AV CONTROL UNIT REPLACEMENT This bulletin applies only to vehicles equipped with Navigation. This bulletin has been amended. Changes have been made throughout. Please discard previous versions of this bulletin.
NTB17-082
Service Bulletin/Repair Instructions
NISSAN; DTC P0456 CAUSED BY EVAP LEAK AT VENT CONTROL VALVE O-RING IF YOU CONFIRM The MIL is ON in an APPLIED VEHICLE with DTC P0456 (EVAP VERY SML LEAK) AND - DTC P0456 is not caused by a loose fuel fill cap (refer to NTB13-097). - An EVAP leak has been detected where the vent control valve mounts to the canister. - The vent control valve O-ring seal is determined to be the cause. ACTION 1. DO NOT REPLACE the vent control valve. 2. Replace the vent control valve O-ring seal (O-ring). - Refer to SERVICE PROCEDURE on page 2.
NTB17-081
Service Bulletin/Repair Instructions
THEFT ALARM SOUNDS WHEN VEHICLE IS LOCKED, UNLOCKED, OR DOOR/TRUNK OPENED IF YOU CONFIRM Intermittently, the theft alarm triggers (horn sounds and lights flash) when one of the following occur: - Using the lock, unlock, or trunk open function on the Intelligent Key - Pushing a handle request switch (door or trunk) - Opening a door or the trunk with the vehicle unlocked and CONSULT-III plus (C-III plus) shows the last item to trigger the theft alarm is BATTERY. - Refer to Check Last Item to Trigger Theft Alarm on the next page. ACTION Replace the Body Control Module (BCM). - Refer to the Electronic Service Manual, section BCS-Body Control Systems, for replacement information. - Use the new BCM listed in the PARTS INFORMATION section.
NTB15-009e
Service Bulletin/Repair Instructions
NAVIGATION SYMPTOMS WHEN SD CARD IS MISSING OR WRONG CARD INSTALLED This bulletin has been amended. Changes have been made throughout. Please discard previous versions of this bulletin.
NTB17-074
Service Bulletin/Repair Instructions
2016-2017 MAXIMA; RUST AROUND REAR LICENSE LAMP FINISHER IF YOU CONFIRM When rust is found on the rear deck lid surface in the area surrounding the license lamp finisher (Figure 1), or when replacing the license lamp finisher for any reason. ACTION - Replace the license lamp finisher with the new replacement part listed in PARTS INFORMATION. - Refer to the Electronic Service Manual (ESM), section EXT ? Exterior, for removal and installation information. - Repair any damaged surfaces that were in direct contact with the license lamp finisher.
NTB12-055f
Service Bulletin/Repair Instructions
CLICKING NOISE FROM FRONT OR REAR AXLE DURING TAKE-OFF/ACCELERATION This bulletin has been amended. The APPLIED VEHICLES section has been revised. No other changes have been made. Please discard previous versions of this bulletin.
NTB15-015h
Service Bulletin/Repair Instructions
PATHFINDER, QUEST, MURANO, MAXIMA, ALTIMA V6; CVT JUDDER AND DTC P17F0 OR P17F1 STORED This bulletin has been amended to remove 2013-2014 Pathfinder from applied vehicles. No other changes have been made. Please discard all previous versions of this bulletin.
NTB12-103e
Service Bulletin/Repair Instructions
CVT / TCM CALIBRATION DATA "WRITE" PROCEDURE This bulletin does not apply to Pathfinder Hybrid, Murano Hybrid or Rogue Hybrid This bulletin has been amended. APPLIED VEHICLES has been updated. SERVICE INFORMATION has been amended. A REPAIR TABLE has been added. Procedural steps have been added to SERVICE PROCEDURE. Discard all previous versions of this bulletin.
NTB15-013d
Service Bulletin/Repair Instructions
NISSAN; PROCEDURE TO CLEAN CVT TRANSMISSION FLUID COOLERS This bulletin has been amended. The APPLIED VEHICLES section has been revised. No other changes have been made. Please discard previous versions of this bulletin.
NTB17-008a
Service Bulletin/Repair Instructions
NISSAN; OIL LEAKING AROUND VALVE TIMING CONTROL SOLENOID VALVE This bulletin applies to vehicles equipped with 6-cylinder engines. For Titan and Titan XD, this bulletin applies only vehicles equipped with gasoline engines. This bulletin has been amended in the PARTS INFORMATION and CLAIMS INFORMATION sections. Discard previous versions of this bulletin.
NTB17-040
Service Bulletin/Repair Instructions
REVISED WHEEL ALIGNMENT SPECIFICATIONS SERVICE INFORMATION For the Applied Vehicles, some wheel alignment specifications listed in the Front Suspension (FSU) and Rear Suspension (RSU) sections of the Electronic Service Manual (ESM) have been revised. Updated ESMs will be distributed to the field as quickly as possible. Until the updated ESMs are made available, please use the corrected specifications listed in this bulletin.
NTB15-015g
Service Bulletin/Repair Instructions
PATHFINDER, QUEST, MURANO, MAXIMA, ALTIMA V6; CVT JUDDER AND DTC P17F0 OR P17F1 STORED This bulletin has been amended to add applied vehicles and change the Parts Information. No other changes have been made. Please discard all previous versions of this bulletin.
NTB16-085a
Service Bulletin/Repair Instructions
ENHANCED DIAGNOSTIC LOGIC FOR CVT This bulletin has been amended to add model years to the Applied Vehicles and part numbers to Table A. No other changes have been made. Please discard all previous versions of this bulletin.
NTB17-033
Service Bulletin/Repair Instructions
2016 MAXIMA; OCCUPANT CLASSIFICATION SYSTEM RETROFIT SERVICE INFORMATION The information in this bulletin is provided for customers who have concerns with their vehicle's Occupant Classification System (OCS) operation after all campaigns have been completed. Follow the steps in this bulletin to determine if this OCS retrofit procedure is applicable to the vehicle you are working on.
NTB17-030
Service Bulletin/Repair Instructions
NISSAN; FUEL TANK IS SLOW OR DIFFICULT TO FILL IF YOU CONFIRM The fuel tank is slow or difficult to fill (filling nozzle shuts off before tank is full). IMPORTANT: Make sure this incident has been duplicated at a gas station by dealer service staff. ACTION Perform the Service Procedure in this bulletin, starting on the next page.
NTB17-017
Service Bulletin/Repair Instructions
2016-2017 MAXIMA; NOISE HEARD WHEN LEANING BACK IN A FRONT SEAT IF YOU CONFIRM A creaking or squeak type noise is heard when sitting in either front seat and leaning back into the lower portion of the seatback. ACTION Apply a small amount of grease to the lumbar support guides. - Perform this repair only to the seat making the noise. - Refer to SERVICE PROCEDURE in this bulletin.
NTB14-068b
Service Bulletin/Repair Instructions
POWER MOONROOF INITIALIZATION SERVICE INFORMATION This bulletin has been amended. The APPPLIED VEHICES section and step 3 on page 3 have been revised. No other changes have been made. Please discard all previous versions.
NTB17-008
Service Bulletin/Repair Instructions
NISSAN; OIL LEAKING AROUND VALVE TIMING CONTROL SOLENOID VALVE This bulletin applies only to Maxima, Quest, Altima Coupe, Altima, Pathfinder and Murano vehicles equipped with V6 engine OR Titan/Titan XD equipped with VK56 engine IF YOU CONFIRM Engine oil is leaking from a valve timing control solenoid valve, And The valve timing control solenoid valve operates correctly and is not externally damaged. ACTION Replace the valve timing control solenoid valve O-ring with a new one using the Service Procedure starting on page 2.
NTB15-009d
Service Bulletin/Repair Instructions
NAVIGATION SYMPTOMS WHEN SD CARD IS MISSING OR WRONG CARD INSTALLED This bulletin has been amended. The APPLIED VEHICLES section has been revised. No other changes have been made. Please discard previous versions of this bulletin.
NTB16-123
Service Bulletin/Repair Instructions
PLASTIC INTERIOR TRIM PROTECTIVE COVERING REMOVAL SERVICE INFORMATION Vehicles are delivered with plastic interior trim protective covering on the front and rear seats, front and rear door panel finishers, steering wheel, and sun visors (see examples on page 2). When removing the protective covering, care must be used to avoid scuffs, scrapes, cuts, and other abrasive contact to interior trim components. DO NOT use sharp objects like razor blades, box cutters, knives, etc. when removing the plastic interior trim protective covering. IMPORTANT All soft trim described in this bulletin is on automatic return to NNA. Any trim found damaged in the way described in this bulletin will be charged back to the dealer.
NTB13-107a
Service Bulletin/Repair Instructions
INTELLIGENT KEY NOT DETECTED / ENGINE WILL NOT START This bulletin has been amended to update the Applied Vehicles and make changes to the body of the bulletin. Please discard previous versions.
NTB16-116
Service Bulletin/Repair Instructions
NISSAN; DIAGNOSIS INFORMATION FOR ABS DTC C1130 SERVICE INFORMATION When diagnosing for DTC C1130 (ENGINE SIGNAL): ECM related DTCs (P-codes) must be diagnosed, repaired, and DTCs erased first. - DTC C1130 is an ABS DTC that indicates an output signal of the ECM is not recognized. - Absent or incorrect ECM signals, that are indicated by corresponding P-codes, may trigger C1130 in the ABS control unit. - Some vehicle features that can be affected by absent or incorrect ECM signals are: - Forward Emergency Braking (FEB) - Intelligent Cruise Control (ICC) - VDC/ABS/TCS
NTB15-049j
Service Bulletin/Repair Instructions
TELEMATICS SERVICE INFORMATION This bulletin has been amended. Information for 2017 Rogue and Rogue Hybrid has been applied. No other changes have been made. Please discard previous versions of this bulletin.
NTB16-067a
Service Bulletin/Repair Instructions
2016 MAXIMA; NAVIGATION UNIT FREEZES 2016 Maxima only in the following states: California (CA), Nevada (NV), Arizona (AZ), Oregon (OR) and Utah (UT) This bulletin has been superseded by NTB16-093 Navigation Freezes, Bluetooth Call Volume Fluctuates, Button Illumination Dim, or USB Device Not Recognized Please discard previous versions of this bulletin.
NTB16-093
Service Bulletin/Repair Instructions
NAVIGATION FREEZES, BLUETOOTH CALL VOLUME FLUCTUATES, BUTTON ILLUMINATION DIM, OR USB DEVICE NOT RECOGNIZED IF YOU CONFIRM A customer reports any of the following issues: For Maxima - - The Map screen freezes or goes blank while driving on a road that has more than eight lanes traveling in the same direction with a navigation route set. For Murano - - Bluetooth phone call volume fluctuates. - Button illumination is too dim. - iPhone not recognized when connected to USB port. AND - Step 6 on page 4 confirms this bulletin is applicable. See Software Version Check and Software Update Confirmation beginning on page 3 to confirm software version. ACTION Update the Navigation system software using the SD card shown on page 2 and the Service Procedure beginning on page 3.
NTB13-077b
Service Bulletin/Repair Instructions
CVT FLUID LEVEL CHECK SERVICE INFORMATION This bulletin has been amended. The APPLIED VEHICLES section has been revised. No other changes have been made. Please discard all previous versions of this bulletin.
NTB15-049i
Service Bulletin/Repair Instructions
TELEMATICS SERVICE INFORMATION ONLY SPECIFIC TRIM PACKAGES ARE AFFECTED This bulletin has been amended. Information for 2017 Altima, Murano, Pathfinder, Sentra, and Titan/Titan XD vehicles has been applied. No other changes have been made. Please discard previous versions of this bulletin.
NTB15-099B
Service Bulletin/Repair Instructions
SERVICE INFORMATION FOR DTCS C1A12 AND C1A16 THIS BULLETIN HAS BEEN AMENDED. THE APPLIED VEHICLES SECTION HAS BEEN REVISED, A PHOTO HAS BEEN ADDED TO PAGE 4, AND ICC/DISTANCE SENSOR LOCATION INFORMATION FOR MAXIMA AND ROGUE HAS BEEN ADJUSTED. NO OTHER CHANGES HAVE BEEN MADE. PLEASE DISCARD PREVIOUS VERSIONS OF THIS BULLETIN.
NTB16-085
Service Bulletin/Repair Instructions
ENHANCED DIAGNOSTIC LOGIC FOR CVT PATHFINDER AND ALTIMA WITH V6 ENGINE ONLY IF YOU CONFIRM THE CUSTOMER REPORTS A TRANSMISSION JUDDER (SHAKE, SHUDDER, SINGLE OR MULTIPLE BUMPS OR VIBRATION). NOTE: A NEW DIAGNOSTIC LOGIC HAS BEEN ESTABLISHED TO ENHANCE THE DIAGNOSTIC PROCESS BY STORING DIAGNOSTIC TROUBLE CODES (DTCS) ON APPLIED VEHICLES. THE NEW DTCS ARE: P17F1 (CVT_JUDDER [C/U INSPECTION]) P17F0 (CVT_JUDDER [T/M INSPECTION]) ACTION 1. REFER TO PAGE 4, STEP 6 IN THE SERVICE PROCEDURE TO CONFIRM THIS BULLETIN APPLIES TO THE VEHICLE YOU ARE WORKING ON. 2. IF THIS BULLETIN APPLIES, REPROGRAM THE TCM (TRANSMISSION CONTROL MODULE).
NTB16-076
Service Bulletin/Repair Instructions
2016 MAXIMA; MIL ON WITH DTC P0116 IF YOU CONFIRM THE MIL IS ON WITH P0116 ENGINE COOLANT TEMPERATURE (ECT SENSOR) STORED, AND THERE ARE NO DRIVABILITY ISSUES. ACTION 1. REFER TO STEP 6 IN THE SERVICE PROCEDURE TO CONFIRM THIS BULLETIN APPLIES TO THE VEHICLE YOU ARE WORKING ON. 2. IF THIS BULLETIN APPLIES, REPROGRAM THE ECM.
NTB13-097D
Service Bulletin/Repair Instructions
ALL MODEL YEAR 2012 AND NEWER NISSAN VEHICLES; EVAP LEAK DTC P0442, P0455, P0456 INFORMATION THIS BULLETIN HAS BEEN AMENDED. THE TITLE HAS BEEN REVISED, AND THE BULLETIN NOW INCLUDES VEHICLES IN PRODUCTION AS OF THE DATE OF THIS UPDATE. NO OTHER CHANGES HAVE BEEN MADE. PLEASE DISCARD ALL PREVIOUS VERSIONS OF THIS BULLETIN.
R1620 2016 MAXIM
Service Bulletin/Repair Instructions
REAR O2 SENSOR VOLUNTARY EMISSIONS RECALL CAMPAIGN ***** CAMPAIGN SUMMARY ***** NISSAN IS CONDUCTING A VOLUNTARY EMISSIONS RECALL CAMPAIGN TO UPDATE THE ELECTRONIC CONTROL MODULE (ECM) SOFTWARE ON CERTAIN MODEL YEAR 2016 NISSAN MAXIMA (A36), AND MODEL YEAR 2015-16 ALTIMA (L33), JUKE (F15), PATHFINDER (R52), MURANO (Z52) AND QUEST (E52) VEHICLES. UNDER CERTAIN CONDITIONS, THE REAR OXYGEN (O2) SENSOR SIGNAL COULD FAIL, RESULTING IN THE REAR OXYGEN (O2) SENSOR OBD MONITOR BEING DISABLED WITHOUT THE CUSTOMER BEING ALERTED. NISSAN PLANS TO BEGIN NOTIFYING OWNERS OF AFFECTED VEHICLES IN AUGUST, ASKING THEM TO BRING THEIR VEHICLES TO AN AUTHORIZED NISSAN DEALERSHIP. ***** WHAT DEALERS SHOULD DO**** 1. VERIFY IF VEHICLES ARE AFFECTED BY THIS VOLUNTARY EMISSION RECALL CAMPAIGN USING SERVICE COMM I.D. R1620. NOTE: NEW VEHICLES IN DEALER INVENTORY CAN BE ALSO BE IDENTIFIED USING DCS (SALES-> VEHICLE INVENTORY, AND FILTER BY OPEN CAMPAIGN). - REFER TO NPSB 15-460 FOR ADDITIONAL INFORMATION 2. THE SUBJECT VEHICLES ARE NOT ON SALES HOLD, BUT FOR CUSTOMER CONVENIENCE, DEALERS ARE ENCOURAGED TO PERFORM THIS CAMPAIGN ON ANY AFFECTED VEHICLES IN THEIR INVENTORY PRIOR TO SALE, LEASE, OR TRADE. 3. DEALERS SHOULD USE NTB16-073 TO CORRECT ANY VEHICLES SUBJECT TO THIS CAMPAIGN. 4. ONCE REPAIRED, DEALER SHOULD SUBMIT A WARRANTY CLAIM AND RELEASE THE VEHICLE.
NTB16-073
Service Bulletin/Repair Instructions
VOLUNTARY EMISSIONS RECALL CAMPAIGN ECM REPROGRAMMING INTRODUCTION NISSAN IS CONDUCTING A VOLUNTARY EMISSION RECALL CAMPAIGN ON CERTAIN MODEL YEAR 2015-2016 ALTIMA, 2015-2016 JUKE, 2016 MAXIMA, 2015-2016 MURANO, 2015-2016 QUEST, AND 2015-2016 PATHFINDER VEHICLES. NISSAN HAS DISCOVERED THAT THESE VEHICLES ARE EQUIPPED WITH AN ON-BOARD DIAGNOSTICS (OBD) CALIBRATION THAT, IF NOT REPAIRED, MAY NOT DETECT A REAR OXYGEN (O2) SENSOR SHORT-TO-GROUND OR SHORT-TO-BATTERY CONDITION. THE ECM (ENGINE CONTROL MODULE) WILL BE REPROGRAMMED. THIS SERVICE WILL BE PERFORMED AT NO CHARGE FOR PARTS OR LABOR. IDENTIFICATION NUMBER NISSAN HAS ASSIGNED IDENTIFICATION NUMBER R1620 TO THIS CAMPAIGN. THIS NUMBER MUST APPEAR ON ALL COMMUNICATIONS AND DOCUMENTATION OF ANY NATURE DEALING WITH THIS CAMPAIGN. DEALER RESPONSIBILITY IT IS THE DEALERS RESPONSIBILITY TO CHECK SERVICE COMM FOR THE CAMPAIGN STATUS ON EACH VEHICLE FALLING WITHIN THE RANGE OF THIS VOLUNTARY EMISSIONS RECALL WHICH FOR ANY REASON ENTERS THE SERVICE DEPARTMENT. THIS INCLUDES VEHICLES PURCHASED FROM PRIVATE PARTIES OR PRESENTED BY TRANSIENT (TOURIST) OWNERS AND VEHICLES IN A DEALERS INVENTORY.
NTB14-012D
Service Bulletin/Repair Instructions
REMOTE ENGINE START NOT WORKING THIS BULLETIN HAS BEEN AMENDED. CHANGES HAVE BEEN MADE TO ITEMS 1, 4, AND 13 IN THE SUPPLEMENTAL DIAGNOSIS TABLE. NO OTHER CHANGES HAVE BEEN MADE. PLEASE DISCARD PREVIOUS VERSIONS OF THIS BULLETIN. SERVICE INFORMATION IF A CUSTOMER STATES THE REMOTE ENGINE START (RES) FEATURE OF AN APPLIED VEHICLE IS NOT WORKING, MAKE SURE THE SYSTEM IS PROPERLY SET TO OPERATE: -THE IGNITION IS TURNED OFF -THE SHIFT SELECTOR IS IN PARK (P) -THE HOOD/DOORS/TRUNK LID/LIFT GATE ARE COMPLETELY CLOSED -NO OTHER OF THE VEHICLES INTELLIGENT KEYS (I-KEYS) ARE INSIDE, OR WITHIN STARTING RANGE OF, THE VEHICLE -THE I-KEY/KEY FOB (KEY FOB) IS WITHIN THE OPERATING RANGE OF 197 FT OR 60 M IF THE ABOVE CONDITIONS ARE MET, RES SHOULD WORK. 1. POINT THE KEY FOB AT THE VEHICLE. 2. PRESS THE LOCK BUTTON. 3. PRESS AND HOLD THE RES BUTTON WITHIN FIVE (5) SECONDS OF PRESSING THE LOCK BUTTON, UNTIL THE TURN SIGNAL LIGHTS TURN ON. WHENEVER AN APPLIED VEHICLE HAS A CONCERN WITH THE REMOTE ENGINE START (RES) FEATURE NOT WORKING PROPERLY, MAKE SURE TO VERIFY THE INCIDENT BEFORE STARTING ANY DIAGNOSIS AND/OR REPLACING PARTS. FOR A BETTER UNDERSTANDING OF THE RES SYSTEM, REFER TO SECTION 3: PRE-DRIVING CHECKS AND ADJUSTMENTS > REMOTE ENGINE START OF THE APPLIED VEHICLES OWNERS MANUAL. WHEN DIAGNOSING RES OPERATION, USE THE SUPPLEMENTAL RES SERVICE INFORMATION AND SUPPLEMENTAL DIAGNOSIS TABLE (STARTING ON PAGE 2) IN ADDITION TO THE ESM.
NTB16-067
Service Bulletin/Repair Instructions
2016 MAXIMA; NAVIGATION UNIT FREEZES 2016 MAXIMA (A36) ONLY IN THE FOLLOWING STATES: CALIFORNIA (CA), NEVADA (NV), ARIZONA (AZ), OREGON (OR) AND UTAH (UT) IF YOU CONFIRM WHILE DRIVING ON A ROAD THAT HAS MORE THAN EIGHT LANES TRAVELING IN THE SAME DIRECTION WITH NAVIGATION ROUTE SET: -MAP FREEZES OR GOES BLANK. -NAVIGATION IS VERY SLOW TO PAGE BETWEEN SCREENS. -VOICE RECOGNITION AND PHONE STEERING WHEEL CONTROLS STOP WORKING. -CD PLAYER WORKS AND PLAYS AUDIO, BUT SCREEN WILL NOT CHANGE TO CD AUDIO DISPLAY. AND -THE AV CONTROL UNITS CURRENT SOFTWARE VERSION IS 107 OR 124. SEE SOFTWARE VERSION CHECK AND SOFTWARE UPDATE CONFIRMATION ON PAGE 3 TO CONFIRM SOFTWARE VERSION. ACTION -UPDATE THE NAVIGATION SOFTWARE WITH SD CARD SHOWN IN SD CARD INFORMATION ON PAGE 2 AND SERVICE PROCEDURE ON PAGE 3.
NTB09-118D
Service Bulletin/Repair Instructions
INTELLIGENT KEY BATTERY VOLTAGE CHECK AND REPLACEMENT THIS BULLETIN HAS BEEN SUPERSEDED BY NTB15-077. NISSAN; SIGNAL TECH-II INTELLIGENT KEY BATTERY TEST AND SIGNAL CHECK PLEASE DISCARD PREVIOUS VERSIONS OF THIS BULLETIN.
NTB15-077A
Service Bulletin/Repair Instructions
NISSAN; SIGNAL TECH-II INTELLIGENT KEY BATTERY TEST AND SIGNAL CHECK THIS BULLETIN HAS BEEN AMENDED. CHANGES HAVE BEEN MADE THROUGHOUT. PLEASE DISCARD PREVIOUS VERSIONS OF THIS BULLETIN. IF YOU CONFIRM THE INTELLIGENT KEY INTERMITTENTLY OR CONTINUOUSLY DOES NOT FUNCTION. ACTION CHECK THE BATTERY CONDITION WITH THE SIGNAL TECH-II I-KEY BATTERY TEST. IMPORTANT: CONFIRM THAT THE SIGNAL TECH-II HAS THE MOST RECENT UPDATE. UPDATE CAN BE PERFORMED THROUGH ASIST / SPECIALTY TOOLS / SIGNAL TECH-II.
NTB11027B
Service Bulletin/Repair Instructions
SERVICE INFORMATION Temporary tire Flat Spotting is common on New Dealer In-Stock vehicles that have not been occasionally moved. Flat Spotting can occur after the vehicle has been parked (not moved) for a few days, or longer. In most cases it is temporary. In extreme cases it can be permanent. Vehicles should be moved every 30 days, in one direction only, enough to rotate the tires 90° (see Figure 1). Moving vehicles as shown will prevent tire Flat Spotting. See this bulletin for further detail.
NTB12103D
Service Bulletin/Repair Instructions
SERVICE INFORMATION The Service Procedure (starting on page 2) in this bulletin contains the steps to perform TCM Calibration Data Write Procedures. These procedures are used when a complete CVT is replaced, or a CVT control valve (valve body) is replaced, or a Transmission Control Module (TCM) is replaced. See this bulletin for further detail.
NTB16057
Service Bulletin/Repair Instructions
IF YOU CONFIRM * The MIL is ON with DTC P0507 (ISC SYSTEM) stored. ACTION 1. Refer to step 6 in the SERVICE PROCEDURE to confirm this bulletin applies to the vehicle you are working on. 2. If this bulletin applies, reprogram the ECM. Please see this bulletinf for further details.
NTB15013C
Service Bulletin/Repair Instructions
IMPORTANT: Metal debris and friction material may become trapped in the radiator, cooling hoses, bypass valve or external CVT fluid cooler. This debris can contaminate the newly serviced transmission, control valve or torque converter. In severe cases this debris can block or restrict flow and may cause damage to the newly serviced CVT. SERVICE INFORMATION When a CVT, control valve or torque converter replacement is necessary for one of the applied vehicles, the CVT transmission fluid coolers (radiator based fluid cooler and external auxiliary cooler if present) must be flushed. Please see this bulletin for further details.
NTB15049H
Service Bulletin/Repair Instructions
SERVICE INFORMATION The Applied Vehicles are equipped with a wireless communication device called a Telematics Communication Unit (TCU). With an active NissanConnectSM Services subscription, the TCU communicates with the NissanConnectSM Services Data Center to provide various security and convenience services. This bulletin contains important service procedures that must be performed properly in order to set-up and maintain the telematics system for the Applied Vehicles. See this bulletin for further detail.
NTB15015F
Service Bulletin/Repair Instructions
IF YOU CONFIRM: The customer reports a transmission judder (shake, shudder, single or multiple bumps or vibration) AND One of these DTCs is stored: - P17F0 (CVT_JUDDER (T/M INSPECTION)) - P17F1 (CVT_JUDDER (C/U INSPECTION)) NOTE - If a transmission judder (as described above) is not reported, this bulletin does not apply. - If either P17F0 or P17F1 are not stored, this bulletin does not apply. - NTB15-014, Enhanced Diagnostic Logic For CVT Judder, has reprogramming instructions that may apply. ACTIONS: Perform the SERVICE PROCEDURE, starting on page 3. - Review the Repair Flow Chart in this bulletin. NOTE: Essential Tool Tech Cam (borescope) J-51951 has been sent to dealers. This tool?s attachments make CVTinspection possible. See this bulletin for further detail.
NTB14-084C
Service Bulletin/Repair Instructions
2-Sensor occupant classification System Diagnostics and Information
NTB16046
Service Bulletin/Repair Instructions
SERVICE INFORMATION Nissan is issuing this Technical Service Bulletin to clarify that a change has been made for the logic that controls the Occupant Classification System (OCS) and 'passenger airbag indicator' (PABI), as described in the Owner?s Manual. This TSB applies only to vehicles using the 2-sensor OCS. Those changes are: * PABI light is ON with an empty front passenger seat. Please see this bulletin for further details.
NTB09099A
Service Bulletin/Repair Instructions
IF YOU CONFIRM A refrigerant leak at a refrigerant pipe/hose joint location. ACTIONS 1. Inspect the metal surfaces of the pipe/hose joint for damage or contamination. NOTE: Do not replace a refrigerant pipe, hose, or other A/C component if an o-ring seal will solve the leak incident, if it should occur. 2. If no damage is found to the joint metal surfaces, replace the O-ring seal. See this bulletin for further detail.
NTB09131B
Service Bulletin/Repair Instructions
SERVICE INFORMATION Because of collision damage or other vehicle repair, a replacement "Certification Label" or "VIN Plate / Label" may be needed. These items may be available from Nissan by request if certain criteria are met. This bulletin lists the criteria and provides an application form for such replacements. See this bulletin for further detail.
NTB16-040
Service Bulletin/Repair Instructions
2016 Maxima; accessory accent lighting flickers
NTB16040
Service Bulletin/Repair Instructions
IF YOU CONFIRM That the interior accent lighting flickers intermittently. ACTION 1. Disconnect the BROWN wire that is part of the Accessory Connector Harness used when the Kit was installed. 2. Please refer to the following SERVICE PROCEDURE which shows the wire which needs to be disconnected. Please see this bulletin for further details.
NTB15-013B
Service Bulletin/Repair Instructions
Nissan; Procedure to clean CVT Transmission fluid coolers
NTB15-014B
Service Bulletin/Repair Instructions
Enhanced Diagnostic Logic for CVT Judder
NTB15014B
Service Bulletin/Repair Instructions
IF YOU CONFIRM The customer reports a transmission judder (shake, shudder, single or multiple bumps or vibration). NOTE: A new diagnostic logic has been established to enhance the diagnostic process by storing diagnostic trouble codes (DTCs) on Applied Vehicles. The new DTCs are: P17F1 (CVT_JUDDER [C/U INSPECTION]) P17F0 (CVT_JUDDER [T/M INSPECTION]) ACTION 1. Refer to page 4, step 6 in the SERVICE PROCEDURE to confirm this bulletin applies to the vehicle you are working on. NOTE:The current TCM Part Numbers in this bulletin have been updated. The vehicle you are working on may require reprogramming per this bulletin again. 2. If this bulletin applies, reprogram the TCM (Transmission Control Module) See this bulletin for further detail.
NTB12-103C
Service Bulletin/Repair Instructions
CVT/TDCM Calibration Data "Write" Procedure
NTB15-015e
Service Bulletin/Repair Instructions
Pathfinder, Quest, Murano, Maxima, Altima V6, CVT Judder and DTC P17F0 or P17F1 Stored
NTB15-044B
Service Bulletin/Repair Instructions
Fuel Filler Cap tether clip service information
NTB15044B
Service Bulletin/Repair Instructions
SERVICE INFORMATION If the clip for the fuel filler cap tether becomes lost or is detached for any reason, it is no longer necessary to replace the fuel filler cap. The clip or "pin" is now available as a separate service part. NOTE - Do not replace the fuel filler cap if only the pin is needed. See this bulletin for further detail.
NTB15-049G
Service Bulletin/Repair Instructions
Telematics Service Information
NTB16-025
Service Bulletin/Repair Instructions
Air Bag Diagnosis sensor unit coinfiguration
NTB16025
Service Bulletin/Repair Instructions
SERVICE INFORMATION If an Air Bag Diagnosis Sensor Unit is replaced and the configuration of the old unit could not be saved, use the Service Procedure in this bulletin to: - Load the VIN specific configuration file from your electronic parts catalog (FAST or equivalent) onto a portable USB storage device (thumb drive) - Plug the thumb drive into your CONSULT PC. - Configure the new Air Bag Diagnosis Sensor Unit using the file that you loaded onto the thumb drive. See this bulletin for further detail.
NTB16-022
Service Bulletin/Repair Instructions
2016 Maxima; door will not open or door will not latch.
NTB16022
Service Bulletin/Repair Instructions
IF YOU CONFIRM The following incident, or the customer reports this incident: The vehicle has been parked (not running) in below freezing temperatures for an extended period (such as overnight). Then The Intelligent Key, key fob, or mechanical keyis used to perform door unlock. Then When attempting to open the door, the door will not open (using either outside or inside handle, or both), or the door will open, but will not latch when closed. Then The door lock and latch functions normally when the vehicle has warmed up (vehicle left in the sun, moved indoors, or driven for several minutes). NOTE: The above incident, if it should occur, could be confirmed or reported for one or more of the four doors. ACTION 1. Replace the door lock of the door(s) that do not open or latch. - Do not replace all four door locks automatically, only replace the door lock of the door(s) with the issue as outlined under IF YOU CONFIRM. 2. Apply RTV silicone sealant and add foam to the new door lock(s). 3. If the issue described under IF YOU CONFIRM applies to the front door(s), perform adjustments to the existing outside handle bracket(s). See this bulletin for further detail.
NTB03074J
Service Bulletin/Repair Instructions
SERVICE INFORMATION Occasionally customers may notice water vapor or fog in the headlamps. The information, illustrations, and flow chart in this bulletin are provided to help you in determining if an incident for water/condensation in the headlamps is normal or not. Nissan?s new vehicle limited warranty does not cover physically damaged (cracked or broken) headlamps. All current headlamp assemblies are vented to the atmosphere (not sealed). - This is necessary to allow for expansion and contraction of air from temperature "variations" (warmer or colder) without damage to the headlamp. - Moisture in the air sometimes "travels" into and out of the headlamp assembly through these vents. - Certain environmental conditions may cause moisture to condense. - The fogging/cloudiness should disappear over time when the headlamp is in a dry environment. See this bulletin for further detail.
NTB16018
Service Bulletin/Repair Instructions
IF YOU CONFIRM The MIL is "ON" with DTC P0603 (ECM BACK UP/CIRCUIT). ACTION 1. Confirm that the battery voltage is 11 volts, or more, with the ignition ON (engine OFF, not running). 2. Erase DTC 3. Perform DTC confirmation steps in the Service Procedure. 4. Confirm 1st trip DTC P0603 is not stored. NOTE: P0603 is often the result of low battery voltage, discharged battery or battery terminal disconnections. Please see this bulletin for furtner details.
NTB16017
Service Bulletin/Repair Instructions
SERVICE INFORMATION When working on the Moonroof, several items can be replaced, repaired, or adjusted, without the need to replace the entire Moonroof assembly. Refer to the following procedures in this bulletin, as needed, to help resolve Moonroof issues. * Knock Insert (Knock) Replacement (Page 2) * Wind Deflector Replacement (Page 7) For wind deflector being damaged, scratched, or having a broken clip. * Trim Panel Replacement (Page 12) For trim panel being damaged, having seal issues or trim panel not being seated. * Moonroof Glass Adjustment (Page 16) For adjusting fit, tightening loose screws or for glass being out of position. * Front or Rear Sunshade Replacement (Page 24) For sunshade replacement due to discoloration,being jammed, out of track, loss of tension or popping/clicking while in motion. * Moonroof or Sunshade Motor Repair (Page 28) For inoperative or noisy. Please see this bulletin for further details.
NTB16014
Service Bulletin/Repair Instructions
SERVICE INFORMATION When diagnosing the front sonar parking sensor for unwanted activation (e.g. sonar activates with no obstacle ahead), inspect the front license plate, front license plate frame and if equipped, the front license plate bracket. See page 2 for example photos. The front sonar parking sensor may activate if the front license plate is bent outward from its bracket (there is a gap between the license plate and the bracket) OR the front license plate frame is bent or loose and is hanging outward, away from the license plate and/or bracket (there is a gap between the license plate frame and the license plate and/or bracket) OR the bracket is loose and is hanging outward, away from the bumper (there is a gap between the bracket and the bumper). If any of these conditions are found, correct it by removing the gap (straighten the license plate, straighten and/or secure the license plate frame, or secure the bracket, as it applies). - Retest the operation of the front sonar parking sensor. If the issue is not resolved, go to ASIST and the related Electronic Service Manual (ESM) for further diagnosis. See this bulletin for further detail.
NTB09081C
Service Bulletin/Repair Instructions
SERVICE INFORMATION The purpose of this bulletin is to give Nissan dealers guidelines to help determine if windshield breakage is covered under warranty or is the customer?s responsibility. Nissan North America (NNA) is not responsible for damage to glass that is a result of objects striking or scratching the glass. However, NNA is responsible for manufacturing issues such as distorted glass and cracks that are due to improper installation or damage to the glass during vehicle assembly. NNA typically does not find any type of cracks in the windshield due to stress after the dealership PDI. See this bulletin for further detail.
NTB15031A
Service Bulletin/Repair Instructions
SERVICE INFORMATION Combination Meter Self-Learning After Replacement 2015 Murano Combination Meters have a learning function when first installed. IMPORTANT: Immediately after initial installation and ignition ON, the combination meter adapts to the way the vehicle is equipped. Performing self-learning can be done only once. Once done, it cannot be changed. CAUTION: Never install a combination meter from an ADAS equipped 2015 Murano into a non-ADAS equipped 2015 Murano, or vice versa, for testing purposes or any other reason. If this incident occurs, the combination meter will need to be replaced. See this bulletin for further detail.
NTB16008
Service Bulletin/Repair Instructions
SERVICE INFORMATION The function to detect the last item to trigger the vehicles theft alarm system can now be accessed with CONSULT-III plus (C-III plus). This function can be accessed by selecting: * Diagnosis (All Systems) or Diagnosis (One System). Then * BCM Then * THEFT ALM Then * Work Support Then * THEFT ALM TRG. See this bulletin for further details.
NTB16001
Service Bulletin/Repair Instructions
SERVICE INFORMATION When the BCM in an APPLIED VEHICLE is being replaced for any reason, all existing Intelligent Keys must be re-registered. If new Intelligent Keys are added to the existing Intelligent Keys at the same time the BCM is being replaced, the procedure in this bulletin must be followed. See this bulletin for further detail.
NTB16002
Service Bulletin/Repair Instructions
SERVICE INFORMATION Whenever all Intelligent Keys of an APPLIED VEHICLE are lost AND the BCM is in Transit Mode, the BCM does not need to be replaced when replacing the lost Intelligent Keys. When all of the following conditions of an APPLIED VEHICLE are verified: - The BCM is in Transit Mode. - The BCM will not respond to CONSULT-III plus (C-III plus). It does not show up on System Call. - All Intelligent Keys are lost. DO NOT replace the BCM or ECM when replacing the lost Intelligent Keys. The procedure in this bulletin will get the existing BCM out of Transit Mode. See this bulletin for further detail.
NTB16003
Service Bulletin/Repair Instructions
SERVICE INFORMATION The Intelligent Keys used on the various Nissan vehicles may not be interchangeable between models and years. See this bulletin for further detail.
PC419A
Service Bulletin/Repair Instructions
This activity will expire on December 18th, 2015. Dealers can continue to schedule and repair vehicles eligible for this service action until close of business December 18th, 2015. Claims will be honored for RO?s opened on or before the 18th of December.
PC419
Service Bulletin/Repair Instructions
Nissan is conducting a dealer inventory service action to inspect and, if necessary, replace the hood latch on certain MY 2015 Murano, MY2016 Maxima, and MY2015-16 Rogue and Pathfinder vehicles
MAILXOL
Service Bulletin/Repair Instructions
Nissan is conducting a Voluntary Emission Service Campaign to provide a warranty supplement card that contains the most current emission warranty information.
NTB09022G
Service Bulletin/Repair Instructions
SERVICE INFORMATION Design and process changes have been made to improve battery voltage at dealer receipt. Our goal is to deliver vehicles to customers with a 12 volt battery in excellent condition. Proper dealership storage and maintenance of vehicle 12 volt batteries is essential to insuring good battery operating life and customer satisfaction. Dealers are responsible for maintaining vehicles in their inventory. 12 volt batteries in vehicle inventory should always be kept at a full charge to prevent excessive discharge during storage and so they are ready for delivery to customers at any time. See this bulletin for further detail.
MAILX
Service Bulletin/Repair Instructions
Nissan is conducting a Voluntary Emission Service Campaign to provide a warranty supplement card that contains the most current emission warranty information.
NTB13028A
Service Bulletin/Repair Instructions
SERVICE INFORMATION Windshield "foreign material" that is on the surface of the glass in some cases can be cleaned off with a very particular type and grade of steel wool. * Most any foreign material on the surface of the Windshield can be cleaned off by using #0000 super fine steel wool. >The #0000 grade super fine steel wool can be found in most hardware stores. Please see this bulletin for further details.
NTB14068A
Service Bulletin/Repair Instructions
SERVICE INFORMATION Power moonroof initialization procedures for the Applied Vehicles have been revised. The procedure described in this bulletin differs from the procedure in the Electronic Service Manual (ESM). At a later date and where possible, the applicable ESMs will be updated with the revised procedures. Follow the procedure in this bulletin should the power moonroof in an Applied Vehicle need to be initialized. See this bulletin for further details.
NTB15009C
Service Bulletin/Repair Instructions
SERVICE INFORMATION Please share this bulletin with "sales staff" and staff associated with maintaining dealer stock vehicles. If an SD Map Card is removed from a Navigation/audio unit for any reason, the card MUST be returned to only the Navigation/audio unit that it came out of. SD Map Cards have data on them that is specific to the Navigation/audio unit that they are originally from, and may cause operational errors if installed into Navigation/audio units that they are not compatible with. - Keep track of any SD Map Cards that are removed from the vehicle by VIN, and return only to the same vehicle that it was removed from. - Do not remove the SD Map Card when returning the Navi/audio head unit for parts warranty. Head units must be returned with correct SD Map Cards or dealer will be charged back. See this bulletin for further detail.
NTB11069C
Service Bulletin/Repair Instructions
IF YOU CONFIRM The customer states HomeLink will not operate or has improper operation. ACTIONS 1. To significantly reduce unnecessary repairs, make sure: a. The vehicle is not in "Transit Mode" (if equipped). - Not in Transit Mode: With the turn signal switch is in the OFF (center) position, turn the ignition from OFF to ON. If the turn signal indicators stay OFF (do not illuminate), the vehicle is not in Transit Mode. b. The "Extended Storage Switch" (if equipped) is in the "Customer Delivery" position (pushed in). - The Extended Storage Switch is located on the fuse block that is located in the interior of the vehicle. 2. Confirm the customer is familiar with the HomeLink programming procedure located in the vehicle?s owner?s manual. 3. Test HomeLink operation with special tool HomeLink Transmitter Tester J-41540. See this bulletin for further detail.
NTB13088A
Service Bulletin/Repair Instructions
SERVICE INFORMATION This bulletin has compiled Tire Pressure Monitor System (TPMS) and Low Tire Pressure Warning System (LTPWS) information for: - Basic diagnosing of TPMS/LTPWS systems - Radio frequency interference causing a "No Data" (C1708, C1709, C1710, C1711) condition - Sensor leaks - Moving TPMS/LTPWS wheel assemblies from one vehicle to another and TPMS/LTPWS sensor registration - Air pressure changes with altitude and ambient temperatures - Aftermarket tire sealers - Aftermarket wheels - Inflating/deflating tires with TPMS/LTPWS sensors See this bulletin for further detail.
NTB15072
Service Bulletin/Repair Instructions
SERVICE INFORMATION On applied vehicles equipped with a rear spoiler, there are two different types. To determine which rear spoiler belongs on your vehicle, see both pages of this bulletin. See this bulletin for further detail.
NTB14057A
Service Bulletin/Repair Instructions
SERVICE INFORMATION The information in this bulletin is provided to help ensure correct diagnosis and repair of fluid leaks. All fluid leaks, when properly diagnosed, should be repaired (whether under warranty or customer pay) to ensure proper vehicle operation. However, certain normal operating conditions can be misdiagnosed as a leak requiring repair. Unnecessary repair or replacement of parts in connection with incorrectly diagnosed "leaks" can negatively impact customer satisfaction, be time consuming and costly, and if not performed correctly can lead to future repairs. See this bulletin for further detail.
NTB15063
Service Bulletin/Repair Instructions
SERVICE INFORMATION If after replacing a BCM and manual configuration needs to be performed, use the table below: CAUTION: * Thoroughly read and understand the vehicle specification. ECU control may not operate normally if the setting is not correct. * Never select any other value other than the ?Setting value? shown below. * If only 1 item is present in the Setting value, only 1 choice is available for the specific vehicle being configured. * Please see this bulletin for further details.
PC384
Service Bulletin/Repair Instructions
Effective immediately, Nissan is placing a temporary Quality Assurance (QA) Hold on 2,823 MY 2016 Maxima vehicles in transit or currently at the dealer. Nissan is currently investigating the issue requiring this quality hold.
NTB15001C
Service Bulletin/Repair Instructions
SERVICE INFORMATION If the AV control unit needs to be replaced in an Applied Vehicle for any reason, follow the Service Procedure in this bulletin to make sure all necessary configurations and registration are completed correctly. NOTE: - The Apps mode will not function if the AV control unit registration code is not registered. - Do not remove the SD Map Card when returning the Navi/audio head unit for parts warranty. Head units must be returned with correct SD Map Cards or the dealer will be charged back. See this bulletin for further detail.
NTB15060
Service Bulletin/Repair Instructions
SERVICE INFORMATION When servicing run flat tires or low profile tires: - Special equipment and procedures are required to avoid damage. - Specifically, Tire Pressure Monitor transmitters (TPMS sensors) can be damaged when improperly dismounting and mounting tires. - TPMS sensors becoming damaged during mounting or dismounting tires are not covered under warranty. - To avoid such damage, ensure that the tire changer being used and the operator of the tire changer is capable of servicing run flat and low profile tires. - Operator?s manuals for such tire changers must be followed. See this bulletin for further detail.
NTB15055
Service Bulletin/Repair Instructions
SERVICE INFORMATION After ECM reprogramming, the Calibration Verification Number (CVN) needs to be automatically calculated prior to State emissions testing (also known as Inspection Maintainence, I/M, or SMOG testing depending upon location). Allowing the vehicle to idle for 22 minutes will allow for faster CVN calculation. It is recommended that customers utilize this method if the vehicle needs to be tested for emissions soon after ECM reprogramming. See this bulletin for further detail.
NTB15052
Service Bulletin/Repair Instructions
SERVICE INFORMATION When replacing both of the vehicle?s I-Keys, due to being lost prior to vehicle delivery, new I-Keys can now be registered without the BCM (or ECM) being replaced. Do not replace the BCM (or ECM) before replacing I-Keys for the Applied Vehicles. Please see this bulletin for further details.
NTB15043
Service Bulletin/Repair Instructions
SERVICE INFORMATION The appearance of painted alloy wheels can be damaged if acidic cleaners are used. DO NOT use Chrome Wheel Cleaner on Painted Wheels. Many chrome wheel cleaners have acidic ingredients. Make sure to follow all instruction in the Appearance and Care Section of the Owner?s Manual. Damage to wheel appearance due to the use of inappropriate chemicals or cleaning products is not covered under warranty. See this bulletin for further detail.
NTB14032
Service Bulletin/Repair Instructions
SERVICE INFORMATION Warranty claims coding for repairing wiring harnesses for all Nissan vehicles has changed. This bulletin gives an outline of the technician?s responsibilities in assisting the dealer?s claims administrator to properly code a harness repair. Failure to provide correct information may result in claims suspension or rejection. See this bulletin for further detail.