Vehicle report

2022 NISSAN PATHFINDER

Compare every NISSAN PATHFINDER yearNHTSA and EPA records

Service bulletins

136 bulletins

Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.

NTB26-006A

Service Bulletin/Repair Instructions

FUEL FILLER TUBE LOWER SEAL IS LEAKING AND DTC P0456 IS STORED IN THE ECM This bulletin is no longer active. Please discard previous versions of NTB26-006.

ITB09-063C

Service Bulletin/Repair Instructions

CERTIFICATION LABEL AND VIN PLATE REPLACEMENT SERVICE INFORMATION Because of collision damage or other vehicle repair, a replacement “Certification Label” or “VIN Plate/Label” may be needed. HINT: Certification Label = FMVSS (Federal Motor Vehicle Safety Standards) label. These items may be available from Infiniti by request if certain criteria are met. This bulletin lists the criteria and provides an application form for such replacements. · The “VIN Plate/Label” (metal plate or vinyl label) is attached to the instrument panel or body on the driver side at the base of the windshield (see Figure 1). · The “Certification Label” (vinyl adhesive label) is located on the lower area of the driver side B-Pillar (see Figure 1).

NTB09-131C

Service Bulletin/Repair Instructions

CERTIFICATION LABEL AND VIN PLATE REPLACEMENT SERVICE INFORMATION Because of collision damage or other vehicle repair, a replacement “Certification Label” or “VIN Plate/Label” may be needed. HINT: Certification Label = FMVSS (Federal Motor Vehicle Safety Standards) label. These items may be available from Nissan by request if certain criteria are met. This bulletin lists the criteria and provides an application form for such replacements. · The “VIN Plate/Label” (metal plate or vinyl label) is attached to the instrument panel or body on the driver side at the base of the windshield (see Figure 1). · The “Certification Label” (vinyl adhesive label) is located on the lower area of the driver side B-Pillar (see Figure 1).

NTB26-006

Service Bulletin/Repair Instructions

FUEL FILLER TUBE LOWER SEAL IS LEAKING AND DTC P0456 IS STORED IN THE ECM IF YOU CONFIRM The vehicle has a visible leak with a smoke machine test coming from the fuel filler tube lower seal, AND DTC P0456 is stored as “Active”, “Past”, or “Pending” in the ECM. ACTION 1. Remove the supplied funnel from the rear of the vehicle or trunk. 2. Insert the funnel completely in the fuel filler tube and remove completely five (5) times. 3. Re-check the fuel filler tube lower seal with a smoke machine to determine visually if any leak is present. 4. If the fuel filler lower seal continues to leak, replace the fuel filler tube. IMPORTANT: The purpose of ACTION (above) is to give you a quick idea of the work you will be performing. You MUST closely follow the entire SERVICE PROCEDURE as it contains information that is essential to successfully completing this repair.

NTB25-030A

Service Bulletin/Repair Instructions

STEERING WHEEL SWITCH BUTTONS INOPERATIVE, STICKING, OR NOT CLICKING WHEN PRESSED IF YOU CONFIRM The customer states that any of the steering wheel switch buttons are inoperative, sticking, or not clicking when pressed. ACTION Follow the SERVICE PROCEDURE to: 1. Remove the steering wheel assembly. 2. Replace the switch assembly on the steering wheel assembly. HINT: The switch assembly includes switches for both sides of the steering wheel. 3. Reinstall the steering wheel assembly. IMPORTANT: The purpose of ACTION (above) is to give you a quick idea of the work you will be performing. You MUST closely follow the entire SERVICE PROCEDURE as it contains information that is essential to successfully completing this repair. This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB25-029

Service Bulletin/Repair Instructions

EXCESS DUST ENTERING CABIN WHILE DRIVING ON DIRT ROADS IF YOU CONFIRM That while driving on dirt roads with all doors and windows closed, that there is excessive dust intrusion into the vehicle’s cabin that is settling on the inside of the doors. ACTION Refer to the SERVICE PROCEDURE in the bulletin to: 1. Install Butyl Patches around the door seals of driver (LH) side and passenger (RH) side front and rear doors. 2. Install drain plugs into door drains of driver (LH) side and passenger (RH) side front and rear doors.

NTB19-033G

Service Bulletin/Repair Instructions

INTELLIGENT CRUISE CONTROL INOPERATIVE AND AEB/FEB WARNING LIGHT ON OR RADAR OBSTRUCTION MESSAGE DISPLAYED WITH DTC C1A16 OR C2582 IF YOU CONFIRM IMPORTANT: The purpose of ACTION (on the next page) is to give you a quick idea of the work you will be performing. You MUST closely follow the entire SERVICE PROCEDURE as it contains information that is essential to successfully completing this repair. Nissan Bulletins are intended for use by qualified technicians, not 'do-it-yourselfers'. Qualified technicians are properly trained individuals who have the equipment, tools, safety instruction, and know-how to do a job properly and safely. NOTE: If you believe that a described condition may apply to a particular vehicle, DO NOT assume that it does. See your Nissan dealer to determine if this applies to your vehicle. The customer states that the ICC stopped working while driving, OR The customer states that the AEB/FEB warning light is ON, or turned ON, while driving (Figure 1), OR The message “Unavailable Front Radar Obstruction” or “Forward Driving Aids Temporarily Disabled Front Sensor Blocked See Owner's Manual” has displayed while driving (Figure 2). AND DTC C1A16, C1A16-97, C2582, or C2582-97 is the ONLY DTC stored. Figure 1 Figure 2 This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin. Forward Driving Aids Temporarily Disabled Front Sensor Blocked See Owner’s Manual

NTB19-042F

Service Bulletin/Repair Instructions

AUTOMATIC EMERGENCY BRAKING WARNING LIGHT BLINKING APPLIED SYSTEMS: Vehicles equipped with a lane camera (see Figure 1) SERVICE INFORMATION If the Automatic Emergency Braking (AEB) warning light or is blinking (but not illuminated steadily) or the customer states it is blinking, and there are no related DTCs, inspect the windshield. A blinking AEB warning light may occur under the following conditions:  When contamination or foreign material adhere to the lane camera viewing window on the windshield.  When driving while it is snowing or when frost forms on the lane camera viewing window on the windshield.  When the lane camera viewing window on the windshield is temporarily fogged up. Figure 1 Nissan Bulletins are intended for use by qualified technicians, not 'do-it-yourselfers'. Qualified technicians are properly trained individuals who have the equipment, tools, safety instruction, and know-how to do a job properly and safely. NOTE: If you believe that a described condition may apply to a particular vehicle, DO NOT assume that it does. See your Nissan dealer to determine if this applies to your vehicle. HINT: o Refer to the applicable ESM for diagnosis if DTCs are present in the Laser/Radar, ICC/ADAS, or Lane Camera systems. o For further information:  Refer to the following pages.  Use the search keyword “blinking” in the ESM.

NTB19-071D

Service Bulletin/Repair Instructions

DTC B00A0-00 STORED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin. IF YOU CONFIRM DTC B00A0-00 (OCCUPANT DETECTION SENSOR UNIT) is stored, AND OCS zero point reset cannot be performed, (continued on the next page)

NTB20-075E

Service Bulletin/Repair Instructions

SOFTWARE UPDATE POP-UP NOTIFICATION This bulletin is no longer active. Please discard previous versions of NTB20-075.

NTB21-037D

Service Bulletin/Repair Instructions

DTCS B2E4B-06, B2E60-06, B2E61-06 DISPLAYED AS CRNT IN THE TCU This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin. IF YOU CONFIRM The customer experiences an issue with the NissanConnect® Service remote commands, AND Any of the following DTCs are displayed as CRNT in the Telematics Control Unit (TCU):  B2E4B-06  B2E60-06  B2E61-06 HINT: These DTCs are caused by an issue with a cloud-server that is related to the TCU. ACTION 1. Do NOT replace the TCU. Replacing the TCU will not resolve the concern. 2. Send an email to NTB21-037@Nissan-Usa.com. IMPORTANT: The purpose of ACTION (above) is to give you a quick idea of the work you will be performing. You MUST closely follow the entire SERVICE PROCEDURE as it contains information that is essential to successfully completing this repair.

NTB22-027B

Service Bulletin/Repair Instructions

DTC B2E01-96 (INTERNAL BATTERY) STORED AS CURRENT IN IVC This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin. SERVICE INFORMATION The APPLIED VEHICLES that come equipped with a factory installed SOS switch, located near the overhead map lamp, also come equipped with a wireless communication device called a Telematics Communication Unit (TCU). With an active NissanConnect® Services subscription, the TCU communicates with the Nissan Data Center to provide various security and convenience services. CONSULT has been updated to allow DTC B2E01-96 for “Internal battery” to be cleared in the TCU. If DTC B2E01-96 is Current/Active in the TCU, and no additional Current/Active DTCs are present in the TCU, perform the SERVICE PROCEDURE starting on page 2.

NTB22-103B

Service Bulletin/Repair Instructions

INFOTAINMENT CONTROL UNIT REPLACEMENT SERVICE INFORMATION APPLIED VEHICLES: 2021-2024 Armada (Y62) 2022-2024 Frontier (D41) – Pro-X and Pro-4X 2022-2024 Pathfinder (R53) 2021-2023 Rogue (T33) 2020-2024 Titan (A61) 2023-2024 Z (Z34) SERVICE INFORMATION When replacing an AV Control Unit (Infotainment Control Unit), for any reason, all three steps below are required. If all three steps are not completed on vehicles equipped with a TCU, the Over The Air (OTA) updates will not work, and other functions may be inoperative. HINT: Not all APPLIED VEHICLES are OTA-update capable. 1. Reprogram the AV Control Unit following the procedure in the ESM. 2. Configure the AV Control Unit following the procedure in the ESM. 3. Write the VIN to the AV Control Unit following the procedure in the ESM along with the supplemental information in this bulletin. IMPORTANT: Steps 1-3 above must be performed in the sequential order shown below. ORDER OF COMPLETION REPROGRAM AV Control Unit CONFIGURE AV Control Unit WRITE VIN to AV Control Unit This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin. SERVICE INFORMATION When replacing an AV Control Unit (Infotainment Control Unit), for any reason, all three steps below are required. If all three steps are not completed on vehicles equipped with a TCU, the Over The Air (OTA) updates will not work, and other functions may be inoperative. HINT: Not all APPLIED VEHICLES are OTA-update capable. 1. Reprogram the AV Control Unit following the procedure in the ESM. 2. Configure the AV Control Unit following the procedure in the ESM. 3. Write the VIN to the AV Control Unit following the procedure in the ESM along with the supplemental information in this bulletin. IMPORTANT: Steps 1-3 above must be performed in the sequential order shown below. ORDER OF COMPLETION REPROGRAM AV Control Unit CONFIGURE AV Control Unit WRITE VIN to AV Control Unit

NTB23-033

Service Bulletin/Repair Instructions

REVISION 3 Please discard earlier versions of this bulletin. The announcement from June 8, 2023 has been revised to include the following: • The restriction on parts for this campaign will be removed and dealers will be able to order parts via normal process beginning July 30, 2024  Parts on order in DBS will be fulfilled

NTB23-031A

Service Bulletin/Repair Instructions

DTC B2E1B-06 (AUTOMATIC ECALL) STORED AS CURRENT IN THE IVC APPLIED VEHICLES: 2021-2022 Armada (Y62) 2022-2023 Frontier (D41) 2023 Kicks (P15) 2021-2023 Maxima (A36) 2022-2023 Pathfinder (R53) 2021, 2023 Rogue (T33) 2022-2023 Sentra (B18) 2020-2021, 2023 Titan/Titan XD (A61) 2023 Versa (N18) AMENDMENT HISTORY PUBLISHED DATE REFERENCE DESCRIPTION April 6, 2023 NTB23-031 Original bulletin published July 22, 2024 NTB23-031A Bulletin no longer active This bulletin is no longer active. Please discard previous versions of NTB23-031.

NTB24-016A

Service Bulletin/Repair Instructions

DTC P161F FOR IMMOBILIZER CODE STORED IN ECM WITH VEHICLE NO-START CONDITION APPLIED VEHICLES: APPLIED DATES: 2022-2023 Pathfinder (R53) Built on or before October 17, 2022 IF YOU CONFIRM The vehicle cranks but will not start, and DTC P161F for “IMMOBILIZER” is stored in the ECM. ACTION Follow the SERVICE PROCEDURE in this bulletin to reprogram the ECM, if applicable. IMPORTANT: The purpose of ACTION (above) is to give you a quick idea of the work you will be performing. You MUST closely follow the entire SERVICE PROCEDURE as it contains information that is essential to successfully completing this repair.

NTB24-036

Service Bulletin/Repair Instructions

VIBRATION AND/OR NOISE FROM THE REAR OF THE VEHICLE APPLIED VEHICLES: 2022-2024 Pathfinder (R53) APPLIED DATES: Built on or before February 28, 2024 APPLIED DRIVETRAINS: AWD IF YOU CONFIRM A binding feeling, vibration, and/or noise coming from the rear end when turning at low speed or accelerating from a stop, AND The issue is resolved by unplugging the Actuator Assembly (AWD Actuator) on the rear Final Drive Unit. ACTION Refer to the SERVICE PROCEDURE below to: 1. Remove the Electro-hydraulic Coupling Assembly (AWD Coupler). 2. Clean the Coupling Oil Tank. 3. Inspect the Breather Tube and Bolt. 4. Replace the Electro-hydraulic Coupling Assembly (AWD Coupler). IMPORTANT: The purpose of ACTION (above) is to give you a quick idea of the work you will be performing. You MUST closely follow the entire SERVICE PROCEDURE as it contains information that is essential to successfully completing this repair.

NTB23-033A

Service Bulletin/Repair Instructions

VOLUNTARY SAFETY RECALL CAMPAIGN 2022-2023 PATHFINDER AND 2021-2023 ROGUE; DRIVER’S SEAT RAIL INSPECTION INTRODUCTION Nissan is conducting this voluntary safety recall campaign on certain specific model year 2022-2023 Pathfinder and 2021-2023 Rogue vehicles to inspect, and if necessary, replace the Driver’s Seat Rail. This service will be performed at no charge to the customer for parts or labor. IDENTIFICATION NUMBER Nissan has assigned identification numbers PC966 and PC980 to this campaign. The applicable number must appear on all communication and documentation of any nature dealing with this campaign. DEALER RESPONSIBILITY It is the dealer’s responsibility to check Service COMM or Dealer Business Systems (DBS) National Service History for the campaign status on each vehicle falling within the range of this voluntary safety recall which for any reason enters the service department. This includes vehicles purchased from private parties or presented by transient (tourist) owners and vehicles in a dealer’s inventory. Federal law requires that new vehicles in dealer inventory which are the subject of a safety recall must be corrected prior to sale. Failure to do so can result in civil penalties by the National Highway Traffic Safety Administration. While federal law applies only to new vehicles, Nissan strongly encourages dealers to correct any used vehicles in their inventory before they are retailed.

NTB20-052C

Service Bulletin/Repair Instructions

REAR DOOR ALERT SERVICE INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB20-073C

Service Bulletin/Repair Instructions

INTELLIGENT KEY UNIT SERVICE INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB20-074B

Service Bulletin/Repair Instructions

BCM SERVICE INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB09-081K

Service Bulletin/Repair Instructions

WINDSHIELD CRACKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB13-028I

Service Bulletin/Repair Instructions

REMOVING FOREIGN MATERIAL FROM THE WINDOW GLASS This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB17-019H

Service Bulletin/Repair Instructions

WINDOW GLASS WARRANTY INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB22-104A

Service Bulletin/Repair Instructions

DIAGNOSING DOOR LOCK OPERATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB24-016

Service Bulletin/Repair Instructions

DTC P161F FOR IMMOBILIZER CODE STORED IN ECM WITH VEHICLE NO-START CONDITION IF YOU CONFIRM The vehicle cranks but will not start, and DTC P161F for “IMMOBILIZER” is stored in the ECM. ACTION Follow the SERVICE PROCEDURE in this bulletin to reprogram the ECM, if applicable.

NTB24-023

Service Bulletin/Repair Instructions

POPPING NOISE FROM FRONT SUSPENSION WHEN TURNING SERVICE INFORMATION Individual strut components are available to service specific issues that have been diagnosed in a strut assembly. If a strut has been confirmed as having a popping noise while turning, refer to the Repair Overview flow chart on page 2 to confirm that the SERVICE PROCEDURE on page 3 applies. HINT: The SERVICE PROCEDURE in this bulletin is only meant to supplement the information found in the Electronic Service Manual (ESM). Refer to the ESM for information to remove and service the vehicle’s struts.

NTB19-042E

Service Bulletin/Repair Instructions

AUTOMATIC EMERGENCY BRAKING WARNING LIGHT BLINKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB23-018G

Service Bulletin/Repair Instructions

NTB23-004A

Service Bulletin/Repair Instructions

MISSING OR CORRUPTED MAP DATA This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB23-018F

Service Bulletin/Repair Instructions

SOFTWARE UPDATE FOR INFOTAINMENT ISSUES This bulletin is no longer active. To access infotainment software updates via the Infotainment Software Update Utility: Select SPECIALTY TOOLS, and then select Infotainment Software Updates on the left side of ASIST. HINT: Initially, the Infotainment Software Update Utility will be available only on the CONSULT PC version of ASIST. The Utility will be added to ASIST WEB at a later date. Please discard previous versions of NTB23-018.

NTB23-079

Service Bulletin/Repair Instructions

MIL IS ON WITH DTC P0300 STORED IN THE ECM IF YOU CONFIRM The MIL is ON with DTC P0300 for âMULTI CYL MISFIREâ stored in the ECM. ACTION Refer to the SERVICE PROCEDURE in this bulletin to: 1. Determine applicable model year specific SERVICE PROCEDURE with the Repair Overview on page 2. 2. Confirm the current ECM and TCM part numbers. 3. Reprogram the ECM and/or the TCM, if applicable.

NTB22-032B

Service Bulletin/Repair Instructions

SEAT BELT REMINDER SERVICE INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB23-073

Service Bulletin/Repair Instructions

GURGLING NOISE FROM MOONROOF AFTER IT RAINS IF YOU CONFIRM The customer states they hear a gurgling / drip / drain noise from the moonroof while driving in the rain. ACTION Follow the SERVICE PROCEDURE in this bulletin to replace the front driver (LH) and front passenger (RH) side moonroof drain tube grommets.

NTB08-097L

Service Bulletin/Repair Instructions

DIAGNOSIS OF VEHICLE PULL (DRIFT) AND/OR STEERING WHEEL OFF-CENTER This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB23-018E

Service Bulletin/Repair Instructions

SOFTWARE UPDATE FOR INFOTAINMENT ISSUES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB23-065

Service Bulletin/Repair Instructions

NOISE FROM MOONROOF WHEN OPEN IF YOU CONFIRM Ticking / flutter / vibrating noise when the moonroof (sunroof) is open and the vehicle is traveling 35-50 mph. ACTION Follow the SERVICE PROCEDURE outlined in this bulletin to install a strip of soft foam in the sunroof opening. IMPORTANT: Do not replace the Wind Deflector to correct the noise concern.

NTB23-018D

Service Bulletin/Repair Instructions

SOFTWARE UPDATE FOR INFOTAINMENT ISSUES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB21-037C

Service Bulletin/Repair Instructions

DTCS B2E4B-06, B2E60-06, B2E61-06 DISPLAYED AS CRNT IN THE TCU This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB23-012A

Service Bulletin/Repair Instructions

SOFTWARE UPDATE FOR INFOTAINMENT ISSUES This bulletin has been superseded by: NTB23-018 SOFTWARE UPDATE FOR INFOTAINMENT ISSUES Please discard previous versions of this bulletin.

2022-Nissan-Path

Service Bulletin/Repair Instructions

OWNERâS MANUAL SUPPLEMENT The information contained within this supplement revises or adds to the âPrecautions on Child Restraintsâ section of the âSafety-Seats, seat belts and supplemental restraint systemâ section in the 2022 NISSAN Pathfinder Ownerâs Manual.

NTB23-049

Service Bulletin/Repair Instructions

12 VOLT BATTERY TESTING FOR IN-SERVICE VEHICLES SERVICE INFORMATION The following Service Information lists NNA procedural recommendations for establishing good connections while performing 12V battery testing. These recommendations are expected to promote uniformity during the connection process, therefore reducing the number of incorrect âTest with DCAâ and âReplaceâ results. HINT: If 12 volt batteries are allowed to discharge for a prolonged period of time, battery life may be drastically reduced. This condition may lead to premature battery replacement and customer dissatisfaction. IMPORTANT: ï· CPX-900 is now an accepted testing tool to use along with or in place of the DSS-5000 ï· CPX-900 operating instructions are found at: https://nissancpx900.midtronics.com/ ï· DSS-5000 operating instructions are found at: https://nissandss5000.midtronics.com/ ï· DCA-8000 is now a required testing tool to be used for all warranty replacement decisions. The DCA-8000 is also a more efficient charger than previously available, and will charge any available 12 volt lead acid battery safely and accurately as long as all precautions and inputs are made correctly. The DCA-8000 operating instructions are found at: https://nissandca8000.midtronics.com/

NTB23-052

Service Bulletin/Repair Instructions

MIL ON WITH DTC P050B STORED IN THE ECM IF YOU CONFIRM The MIL is ON and DTC P050B COLD START CONTROL is stored in the ECM. ACTION Follow the SERVICE PROCEDURE in this bulletin to reprogram the ECM, if applicable.

NTB23-053

Service Bulletin/Repair Instructions

SILICONE-BASED LUBRICANT OR GREASE CAN DAMAGE ELECTRICAL COMPONENTS SERVICE INFORMATION Do not apply Silicone-based lubricants or grease to, or around, any interior electrical components. To avoid the risk of death or severe personal injury, do not directly spray Silicone-based lubricant or grease, or inadvertently overspray Silicone-based lubricant or grease onto any interior electrical components. These types of lubricants can be detrimental to the proper operation of electrical components.

PC968 2022 Pathf

Service Bulletin/Repair Instructions

EZ Flex Seat Ownerâs Manual Supplement Voluntary Service Campaign *****Dealer Announcement***** Nissan is providing owners of approximately 67,546 2022 Nissan Pathfinder vehicles with a supplemental Ownerâs Manual addendum. The 2022 Pathfinder Ownerâs Manual instructions for the 2nd row seat does not indicate that the one-touch seat release function may operate while driving the vehicle. Customers will be asked to place the supplement, which addresses the functionality of the one-touch seat release on the 2nd row seat while driving, inside the Ownerâs Manual that came with their vehicle. *****What Dealers Should Do***** 1. Verify if new vehicles in their inventory are affected by this Voluntary Service Campaign using Service Comm or DBS National Service History â Open Campaigns I.D. PC968. â¢ New vehicles in dealer inventory can also be identified using DBS (Sales-> Vehicle Inventory, and filter by Open Campaign). ï§ Refer to NPSB 15-460 for additional information ï§ SERVICE COMM will only be active for vehicles in dealer new vehicle inventory. 2. If a dealer receives a supplemental Ownerâs Manual addendum for a vehicle they have retailed, currently have in their new vehicle or pre-owned inventory, or a Nissan Rental Car (NRC), the dealer should either forward the ownerâs manual supplement to the current owner or add the supplement to the Ownerâs Manual in the glove box of any affected vehicle they currently control. 3. Customers receiving this Ownerâs Manual supplement have been advised to place it inside the Ownerâs Manual that came with their vehicle.

NTB21-072A

Service Bulletin/Repair Instructions

A/C INOPERATIVE WITH DTC B20C8-14 STORED IN THE IPDM E/R This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB22-103A

Service Bulletin/Repair Instructions

INFOTAINMENT CONTROL UNIT REPLACEMENT SERVICE INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB23-043

Service Bulletin/Repair Instructions

AUTOMATIC BACK DOOR PARTIALLY OPENS IF YOU CONFIRM The automatic back door will only open partially and then will change to âmanual modeâ when using the Intelligent Key, back door request button, or the interior dash button, OR Any one or combination of the DTCs listed below are stored in AUTO BACK DOOR ECU. ï· U2154-87 CAN Comm Circuit ï· B2417-15 Touch Sensor Circuit LH Open ï· B2416-15 Touch Sensor Circuit RH Open ï· B2426-25 Spindle Sensor LH ï· B2427-11 Spindle Sensor RH ï· B2437-13 Spindle Motor RH ACTION Replace the Automatic Back Door Control Unit.

NTB13-107F

Service Bulletin/Repair Instructions

VEHICLE KEY NOT DETECTED / AUTHENTICATED, ENGINE WILL NOT START This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB16-003C

Service Bulletin/Repair Instructions

INTELLIGENT KEY REPLACEMENT OR SWAPPING BETWEEN VEHICLES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.

NTB18-071C

Service Bulletin/Repair Instructions

SECURITY ALARM SOUNDS AFTER USING MECHANICAL KEY TO UNLOCK DRIVER DOOR This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB23-018C

Service Bulletin/Repair Instructions

SOFTWARE UPDATE FOR INFOTAINMENT ISSUES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB23-031

Service Bulletin/Repair Instructions

DTC B2E1B-06 (AUTOMATIC ECALL) STORED AS CURRENT IN IVC SERVICE INFORMATION The APPLIED VEHICLES that come equipped with a factory installed SOS switch, located near the overhead map lamp, also come equipped with a wireless communication device called a Telematics Communication Unit (TCU). With an active NissanConnectÂ® Services subscription, the TCU communicates with the Nissan Data Center to provide various security and convenience services. 1. When diagnosing DTC B2E1B-06 (AUTOMATIC ECALL) on an APPLIED VEHICLE: ï· If DTC B2E1B-06 is not âCRNTâ in the IVC, DO NOT replace the TCU. Erase the DTC. No further steps are needed. ï· If DTC B2E1B-06 is âCRNTâ in the IVC, replace the TCU. o Refer to the ESM: REPAIR > DRIVER INFORMATION & MULTIMEDIA > AUDIO, VISUAL & NAVIGATION SYSTEM > REMOVAL AND INSTALLATION > TCU

NTB03-074Q

Service Bulletin/Repair Instructions

HEADLAMP, FOG LAMP, OR REAR COMBINATION LAMP FOGGING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB12-055J

Service Bulletin/Repair Instructions

CLICKING NOISE FROM FRONT OR REAR AXLE DURING TAKE-OFF/ACCELERATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB21-013B

Service Bulletin/Repair Instructions

PREVENT FRONT AXLE THREAD DAMAGE DURING NUT REMOVAL This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB23-018B

Service Bulletin/Repair Instructions

SOFTWARE UPDATE FOR INFOTAINMENT ISSUES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB21-005C

Service Bulletin/Repair Instructions

REMOTE ENGINE START This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.

NTB21-063D

Service Bulletin/Repair Instructions

COMBINATION METER MODULES OR ABS CONTROL UNITS CANNOT BE SWAPPED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB23-022

Service Bulletin/Repair Instructions

INTERMITTENT OPERATION OF HVAC BLOWER IF YOU CONFIRM The HVAC blower is inoperative at initial vehicle start up, OR The customer states the HVAC blower has been inoperative during initial vehicle start up. ACTION Follow the SERVICE PROCEDURE on the next page to: 1. Confirm the current A/C Amplifier part number. 2. Reprogram the A/C Amplifier, if needed.

NTB23-018A

Service Bulletin/Repair Instructions

SOFTWARE UPDATE FOR INFOTAINMENT ISSUES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB19-042D

Service Bulletin/Repair Instructions

AUTOMATIC EMERGENCY BRAKING WARNING LIGHT BLINKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB19-071C

Service Bulletin/Repair Instructions

DTC B00A0-00 STORED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB22-032A

Service Bulletin/Repair Instructions

SEAT BELT REMINDER SERVICE INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB23-018

Service Bulletin/Repair Instructions

SOFTWARE UPDATE FOR INFOTAINMENT ISSUES SERVICE INFORMATION When diagnosing an infotainment issue or after replacement of the AV Control Unit, it is necessary to verify the current software version of the AV Control Unit to determine if a software version update is required. Use the vehicle tables in this bulletin to determine the current software version, if the AV Control Unit requires a software version update, and which procedure to use to update the AV Control Unit. The software updates in this bulletin are to address stability improvements and âbugâ fixes. IMPORTANT: If the customer is experiencing a software related concern, refer to NTB21-038 to verify if the customer concern is a hardware or software related issue. If the concern is a software related issue, review the information in this bulletin to update the AV Control Unit as needed.

NTB09-081J

Service Bulletin/Repair Instructions

WINDSHIELD CRACKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB13-028H

Service Bulletin/Repair Instructions

REMOVING FOREIGN MATERIAL FROM THE WINDOW GLASS This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB08-097K

Service Bulletin/Repair Instructions

DIAGNOSIS OF VEHICLE PULL (DRIFT) AND/OR STEERING WHEEL OFF-CENTER This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB10-126C

Service Bulletin/Repair Instructions

WHEEL BEARING COLLISION DAMAGE This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB20-010C

Service Bulletin/Repair Instructions

WINDSHIELD WIPER BLADE PERFORMANCE/DIAGNOSIS SERVICE INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB20-075D

Service Bulletin/Repair Instructions

SOFTWARE UPDATE POP-UP NOTIFICATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.

NTB23-012

Service Bulletin/Repair Instructions

SOFTWARE UPDATE FOR INFOTAINMENT ISSUES IF YOU CONFIRM The customer is experiencing a software related concern. ï· Refer to NTB21-038 to verify if the customer concern is a hardware or software related issue. ACTION 1. Refer to steps 1 - 4, starting on page 3, to confirm if the current software begins with â4901â or â5327â. 2. If the current software does begin with â4901â or â5327â, update the software using the steps in the SERVICE PROCEDURE.

NTB20-085B

Service Bulletin/Repair Instructions

TELEMATICS CONTROL UNIT RESET AFTER AUTOMATIC COLLISION NOTIFICATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB22-098A

Service Bulletin/Repair Instructions

SERVICE INFORMATION FOR DISTANCE SENSOR DTC DIAGNOSIS This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB22-027A

Service Bulletin/Repair Instructions

DTC B2E01-96 (INTERNAL BATTERY) STORED AS CURRENT IN IVC This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB23-004

Service Bulletin/Repair Instructions

MISSING OR CORRUPTED MAP DATA IF YOU CONFIRM Customer states the error screen, shown in Figure 1, appears when using navigation. ACTION Follow the SERVICE PROCEDURE in this bulletin to download the map data from the ASIST Downloader, and then update the AV Control Unit with the map data.

NTB23-001

Service Bulletin/Repair Instructions

THE VEHICLE ALARM SOUNDS WHEN UNLOCKING AND/OR OPENING THE DOORS WITH THE INTELLIGENT KEY IF YOU CONFIRM The customer states that the vehicle security system (alarm) may inadvertently sound when unlocking and/or opening any of the vehicle's doors with the Intelligent Key. ACTION 1. Confirm the current BCM hardware part number. HINT: This number is the hardware number on the outside of the BCM, and can also be found with C-III plus. 2. If the current hardware part number is 284B1-6TA0E, replace the BCM with the part listed in the PARTS INFORMATION. HINT: If the current part number is not 284B1-6TA0E, this bulletin does not apply. Please refer to the ESM for further diagnostic information. ï· Refer to the ESM: ELECTRICAL & POWER CONTROL > BODY CONTROL SYSTEM > REMOVAL AND INSTALLATION > BCM (BODY CONTROL MODULE) > Removal and Installation ï· After replacing the BCM, perform ADDITIONAL SERVICE WHEN REPLACING BCM. o Refer to the ESM: ELECTRICAL & POWER CONTROL > BODY CONTROL SYSTEM > BASIC INSPECTION > ADDITIONAL SERVICE WHEN REPLACING BCM > Work Procedure

REVISION 2 PC939

Service Bulletin/Repair Instructions

Air Conditioner Condenser Pipe Voluntary Emission Service Campaign REVISED December 22, 2022 Please discard earlier versions of this bulletin. The announcement under campaign ID PC899, from August 5, 2022 has been revised to include the following: â¢ Vehicles previously identified under PC899 are now identified in Service Comm as PC939. â¢ Repair bulletin NTB22-059 has been revised and is now available: ï Dealers will now inspect the Air Conditioner (AC) System for leak, and if found to be leaking will replace the AC Pipe, ancillary parts, and refill with refrigerant. â¢ Owner notification letters will be mailed January 2023 instructing them to bring their vehicle to an authorized Nissan dealer to have the remedy work completed at no cost to the owner.

NTB21-037B

Service Bulletin/Repair Instructions

DTCS B2E4B-06, B2E60-06, B2E61-06 STORED IN THE TCU This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB22-104

Service Bulletin/Repair Instructions

DIAGNOSING DOOR LOCK OPERATION SERVICE INFORMATION If a customer describes a concern of a door not opening and/or unlocking properly, on any of the APPLIED VEHICLES, use the Questions for the Customer below to help reproduce the concern, and then follow the SERVICE PROCEDURE starting on page 2 to determine if the Door Lock should be replaced. ï· Do not replace a Door Lock unless instructed to by the SERVICE PROCEDURE. Questions for the Customer: ï· When did you first notice the issue? ï· Is it consistent or intermittent? ï· Under what conditions does it occur? ï· Does it seem more likely to happen to a specific passenger/person in your family? ï· Has there been any change to the issue since it first began?

NTB22-103

Service Bulletin/Repair Instructions

INFOTAINMENT CONTROL UNIT REPLACEMENT SERVICE INFORMATION SERVICE INFORMATION When replacing an AV Control Unit (Infotainment Control Unit), for any reason, all three steps below are required. If all three steps are not completed on vehicles equipped with a TCU, the Over The Air (OTA) updates will not work, and other functions may be inoperative. HINT: Not all APPLIED VEHICLES are OTA-update capable. 1. Reprogram the AV control unit. 2. Configure the AV control unit. 3. Write the VIN to the AV control unit. IMPORTANT: Steps 1-3 above must be performed in the sequential order shown below.

NTB22-101

Service Bulletin/Repair Instructions

DRIVE SHAFT BOOT SERVICE INFORMATION SERVICE INFORMATION If a Drive Shaft (Axle Shaft) Boot on an APPLIED VEHICLE is found to be leaking grease, AND There is no abnormal noise or obvious CV Joint risk due to water intrusion and/or complete grease loss, check for REPAIR KIT-DUST BOOT (CV Joint Boot Kit) availability. ï· If there is a REPAIR KIT-DUST BOOT (CV Joint Boot Kit) available for the vehicle being repaired, do NOT replace the axle. Install a new boot kit following the procedure in the ESM. o Refer to the ESM: TRANSMISSION & DRIVELINE > FRONT AXLE > REMOVAL AND INSTALLATION > FRONT DRIVE SHAFT BOOT o If the complete axle (drive shaft) is replaced when only a new boot is required, the over-repair may be charged back to the dealer. ï· If there is NOT a REPAIR KIT-DUST BOOT (CV Joint Boot Kit) available for the vehicle being repaired, refer to the ESM for further diagnostic information. IMPORTANT: When servicing vehicles with staked axle nuts, refer to NTB21-013 to prevent Drive Shaft thread damage.

NTB10-029I

Service Bulletin/Repair Instructions

ABNORMAL NOISE, VIBRATION AND/OR BINDING FEELING FROM REAR DIFFERENTIAL This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB22-098

Service Bulletin/Repair Instructions

SERVICE INFORMATION FOR DISTANCE SENSOR DTC DIAGNOSIS SERVICE INFORMATION If DTC C2581-78 (Distance sensor) and/or C2581-92 (Distance sensor) are stored as CURRENT in the LASER/RADAR system, and there is no external impact damage to the outside of the front bumper fascia, the following SERVICE PROCEDURE must be followed prior to replacing any components. ï· Impact damage to the front bumper fascia, distance sensor or distance sensor bracket is not warrantable, and not covered by this SERVICE PROCEDURE.

NTB20-029F

Service Bulletin/Repair Instructions

TELEMATICS (IVC) SERVICE INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.

NTB22-069A

Service Bulletin/Repair Instructions

MISFIRE DTCS STORED IN THE ECM DURING COLD START This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB22-088

Service Bulletin/Repair Instructions

LANE CAMERA OVER TEMPERATURE DTC STORED SERVICE INFORMATION The Lane Camera can become overheated if the interior room temperature or temperature around the camera becomes excessively high, and does not initially indicate a sustained fault. If overheated, the Lane Camera should be cooled to outside ambient temperature, any stored DTCs erased, and then allowed to resume operation. Refer to the ESM for any DTCs that will not erase. This condition may cause the following system functions to be suspended: ï· Vehicle-to-vehicle distance control mode (ICC - Intelligent Cruise Control) ï· Conventional (fixed speed) cruise control mode ï· Steering wheel assistance function ï· AEB (Automatic Emergency Braking) ï· LDW (Lane Departure Warning) ï· I-LI (Intelligent Lane Intervention) ï· Blind Spot Intervention ï· TSR (Traffic Sign Recognition) AND Can store one or more of the following DTCs as PAST or CURRENT: ï· C2501-4B (Front camera unit) ï· C1F05-4B (Front camera unit) ï· C1F6B-4B (Front camera unit) For customer information, see Talk Tip "Customer" statement on page 3.

NTB12-055I

Service Bulletin/Repair Instructions

CLICKING NOISE FROM FRONT OR REAR AXLE DURING TAKE-OFF/ACCELERATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB21-013A

Service Bulletin/Repair Instructions

PREVENT FRONT AXLE THREAD DAMAGE DURING NUT REMOVAL This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB21-081C

Service Bulletin/Repair Instructions

AUTOMATIC BACK DOOR INOPERATIVE This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB22-004A

Service Bulletin/Repair Instructions

INFOTAINMENT SYSTEM REBOOTS EVERY 4-5 MINUTES This bulletin has been superseded by: NTB22-060 / Campaign # PC901 VOLUNTARY SAFETY RECALL CAMPAIGN INFOTAINMENT SYSTEM REBOOTS EVERY 4-5 MINUTES OR NTB22-061 / Campaign # PC902 VOLUNTARY SAFETY RECALL CAMPAIGN INFOTAINMENT SYSTEM REBOOTS EVERY 4-5 MINUTES ï· Check Service COMM or Dealer Business Systems (DBS) National Service History to confirm campaign eligibility. ï· Please discard previous versions of this bulletin.

NTB22-069

Service Bulletin/Repair Instructions

MISFIRE DTCS STORED IN THE ECM DURING COLD START IF YOU CONFIRM Any single or combination of the following DTCs are present in the ECM during a cold start warm-up cycle on an APPLIED VEHICLE: ï· P0300 (MULTI CYL MISFIRE) ï· P0301 (CYL 1 MISFIRE) ï· P0302 (CYL 2 MISFIRE) ï· P0303 (CYL 3 MISFIRE) ï· P0304 (CYL 4 MISFIRE) ï· P0305 (CYL 5 MISFIRE) ï· P0306 (CYL 6 MISFIRE) AND There is no drivability concern present. ACTION Follow the SERVICE PROCEDURE in this bulletin to reprogram the ECM, if applicable.

REVISION 1 PC899

Service Bulletin/Repair Instructions

Air Conditioner Condenser Pipe Voluntary Emission Service Campaign REVISED August 5, 2022 Please discard earlier versions of this bulletin. The announcement from July 22, 2022 has been revised to include the following: â¢ The parts restriction will be removed on the following parts and dealers will be able to order, as needed, via normal ordering process beginning August 12, 2022. ï 92471-N823A O-Ring ï 92472-N823A Seal O-Ring ï 92477-6RR1A O-Ring ï 92477-6RR2A Seal O-Ring ï 62090-6TA0B Absorber-Energy, Front Bumper â¢ The following part will remain on restriction and may be ordered via DBS. ï 92446-6SA0K Pipe Assembly

NTB22-059

Service Bulletin/Repair Instructions

VOLUNTARY EMISSION SERVICE CAMPAIGN 2022 PATHFINDER; A/C CONDENSER PIPE INTRODUCTION Nissan is conducting this voluntary emission service campaign, on certain specific model year 2022 Pathfinder vehicles, to replace the A/C condenser pipe. This service will be performed at no charge to the customer for parts or labor. IDENTIFICATION NUMBER Nissan has assigned identification number PC899 to this campaign. This number must appear on all communication and documentation of any nature dealing with this campaign. DEALER RESPONSIBILITY Dealers are to repair vehicles falling within range of this campaign that enter the service department. This includes vehicles purchased from private parties, vehicles presented by transient (tourists) owners, and vehicles in a dealerâs inventory.

PC899 Pathfinder

Service Bulletin/Repair Instructions

Air Conditioner Condenser Pipe Voluntary Emission Service Campaign *****Campaign Summary***** Nissan is conducting a Voluntary Emission Service Campaign to correct a potential refrigerant leak on specific model year 2022 Nissan Pathfinder vehicles identified in Service Comm and DBS National Service History. Affected vehicles may have reduced Air Conditioner (AC) cooling performance due to a refrigerant leak caused by a seal manufacturing issue that has since been corrected. The dealer will evacuate the Air Conditioner (AC) System, replace the AC Pipe and ancillary parts, and refill with refrigerant. Affected vehicles are not subject to stop sale. *****What Dealers Should Do***** 1. Verify if vehicles are affected by this Voluntary Emission Service Campaign using Service Comm or DBS National Service History â Open Campaigns I.D. PC899. 2. Dealers are requested to remedy any affected vehicles in dealer pre-owned inventory to ensure customer satisfaction. 3. Dealers should use NTB22-059 to correct any vehicles subject to this campaign. 4. Once repaired, dealers should submit the claim using the claims coding provided, and release the vehicle.

NTB22-050

Service Bulletin/Repair Instructions

LOW SPEED TRANSMISSION UPSHIFT IMPROVEMENT IF YOU CONFIRM The customer notices a 1st to 2nd gear upshift while driving at slow speeds and when the transmissionâs fluid temperature is warming up, AND There are no TCM related DTCs present. ACTION Perform the steps in the SERVICE PROCEDURE to: 1. Confirm the current TCM part number. 2. Reprogram the TCM, if applicable.

NTB10-029H

Service Bulletin/Repair Instructions

NISSAN AWD MODELS; ABNORMAL NOISE, VIBRATION AND/OR JUDDER FROM REAR DIFFERENTIAL This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB22-036

Service Bulletin/Repair Instructions

KNOCK NOISE OVER BUMPS FROM SECOND ROW SEATS IF YOU CONFIRM A knocking and/or rattling noise is heard in one, or both, second row seat(s), when driving over uneven or rough road surfaces. ACTION Perform the SERVICE PROCEDURE, starting on page 2, to install two (2) plastic washers into each seat. NOTE: This procedure will be applied to both the incident seat, as well as the remaining second row seat.

NTB21-069A

Service Bulletin/Repair Instructions

ELECTRONIC SHIFTER ASSEMBLY This bulletin has been amended. See AMENDMENT HISTORY. Please discard previous versions of this bulletin.

NTB22-032

Service Bulletin/Repair Instructions

SEAT BELT REMINDER SERVICE INFORMATION SERVICE INFORMATION On the APPLIED VEHICLES, there are a variety of Seat Belt Warning Lights and Chimes. Refer to the information in this bulletin, along with the related vehicle ownerâs manual.

NTB19-071B

Service Bulletin/Repair Instructions

DTC B00A0-00 STORED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB20-085A

Service Bulletin/Repair Instructions

TELEMATICS CONTROL UNIT RESET AFTER AUTOMATIC COLLISION NOTIFICATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB22-030

Service Bulletin/Repair Instructions

âSERVICE AT POWER REDUCEDâ WARNING DISPLAYED AND DTC P0715 STORED IN THE TCM IF YOU CONFIRM The customer states the âService AT Power reducedâ warning message (Figure 1) is/was displayed, AND DTC P0715 (INPUT SPEED SENSOR A) is the only DTC stored in the TCM. NOTE: DTC P0715 may be stored as âPastâ. ACTION 1. Confirm the current TCM part number. 2. Reprogram the TCM, if applicable. NOTE: If DTC P0715 stores again after successful reprogramming, refer to ASIST and the ESM for further diagnosis/repairs.

NTB22-027

Service Bulletin/Repair Instructions

B2E01-96 (INTERNAL BATTERY) DTC STORED AS CURRENT IN IVC SERVICE INFORMATION CONSULT has been updated to allow DTC B2E01-96 (Internal battery) to be cleared in the Telematics Control Unit (TCU). If DTC B2E01-96 is Current/Active in the TCU, and No additional Current/Active DTCs are present in the TCU, perform the SERVICE PROCEURE starting on page 2.

NTB22-026

Service Bulletin/Repair Instructions

SERVICE INFORMATION FOR FUEL GAUGE INACCURATE WITH DTCS STORED IN ECM SERVICE INFORMATION If a fuel level sensor has been diagnosed as sending an incorrect level signal, and one or more of the following DTCs are stored in the ECM, do not replace the entire âFuel Level Sensor Unit, Fuel Filter and Fuel Pump Assemblyâ (fuel pump assembly). The fuel level sensor can be replaced separately. ï· P0460 (FUEL LEV SEN SLOSH) ï· P0461 (FUEL LEVEL SENSOR) ï· P0462 (FUEL LEVL SEN/CIRC) ï· P0463 (FUEL LEVL SEN/CIRC) NOTE: Warranty claims referring to fuel level issues that result in the replacement of the entire fuel pump assembly will be charged back.

NTB21-063C

Service Bulletin/Repair Instructions

COMBINATION METER MODULES OR ABS CONTROL UNITS CANNOT BE SWAPPED This bulletin has been amended. See AMENDMENT HISTORY, below. Please discard previous versions of this bulletin.

NTB10-029G

Service Bulletin/Repair Instructions

NTB22-020

Service Bulletin/Repair Instructions

SERVICE INFORMATION FOR BRAKE SWITCH ADJUSTMENT FOR DTC C1142 AND/OR C1116 STORED SERVICE INFORMATION DTC C1142 (PRESS SEN CIRCUIT) and/or C1116 (STOP LAMP SW) may be stored if the Stop Lamp Switch and/or the Brake Pedal Position Switch are out of adjustment. Before replacing any components for DTCs C1142 (PRESS SEN CIRCUIT) and/or C1116 (STOP LAMP SW), stored as past or current, confirm that the Stop Lamp Switch and the Brake Pedal Position Switch are properly adjusted. If either the Stop Lamp Switch and/or the Brake Pedal Position Switch are found to be out of adjustment, adjust them as per the ESM, and then clear the DTCs and perform DTC confirmation. ï· Refer to the ESM: BRAKES > BRAKE SYSTEM > PERIODIC MAINTENANCE > BRAKE PEDAL > Adjustment

NTB20-029E

Service Bulletin/Repair Instructions

TELEMATICS (IVC) SERVICE INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.

NTB18-071B

Service Bulletin/Repair Instructions

SECURITY ALARM SOUNDS AFTER USING MECHANICAL KEY TO UNLOCK DRIVER DOOR This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB21-081B

Service Bulletin/Repair Instructions

AUTOMATIC BACK DOOR INOPERATIVE This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB13-097J

Service Bulletin/Repair Instructions

EVAP LEAK DTC P0442, P0455, P0456 INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB17-082E

Service Bulletin/Repair Instructions

DTC P0456 CAUSED BY EVAP LEAK AT VENT CONTROL VALVE O-RING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB22-004

Service Bulletin/Repair Instructions

INFOTAINMENT SYSTEM CONSTANTLY REBOOTS EVERY 4-5 MINUTES IF YOU CONFIRM The Infotainment system reboots (restarts) every 4 to 5 minutes, AND The APPLIED VEHICLE is, or was, part of a rental fleet. EXAMPLE: Enterprise, Avis, etc. ACTION Follow the service procedure in this bulletin to update the AV control unit.

NTB21-063A

Service Bulletin/Repair Instructions

COMBINATION METERS CANNOT BE SWAPPED This bulletin has been amended. See AMENDMENT HISTORY below. Please discard previous versions of this bulletin.

NTB17-045C

Service Bulletin/Repair Instructions

CLEANING FRONT OR REAR COMBINATION LAMP ASSEMBLIES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB99-001F

Service Bulletin/Repair Instructions

STRUT AND SHOCK ABSORBER REPLACEMENT GUIDELINES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB21-109

Service Bulletin/Repair Instructions

DTC P0805 FOR CLUTCH POSITION SENSOR A STORED IN TCM IF YOU CONFIRM DTC P0805 (Clutch Position Sensor A) is stored in the TCM. NOTE: The customer may have stated: ï· The MIL was ON. ï· The Idle Stop System Fault message (Figure 1) was displayed. ï· They experienced a drivability concern. ACTION 1. Confirm the current TCM part number. 2. Reprogram the TCM, if applicable. NOTE: If DTC P0805 stores again, after successful reprogramming, refer to ASIST and the ESM for further diagnosis/repairs.

PC852 2022 Pathf

Service Bulletin/Repair Instructions

Main Harness Routing Dealer Inventory *****Dealer Announcement***** Nissan is conducting a dealer inventory quality action to inspect the main wiring harness, install a section of wiring conduit and reroute the harness on 2,059 specific MY2022 Nissan Pathfinder vehicles identified in Service Comm and National Service History â Open Campaigns. During manufacturing, the main wiring harness may have been misrouted at the fuse box connection causing contact with the fuse box. Affected vehicles are subject to stop sale and are either currently in dealer inventory or assigned and in transit to the dealer. *****What Dealers Should Do***** PLEASE FOLLOW THE ATTACHED INSTRUCTIONS: 1. Verify if vehicles are affected by this quality action using Service Comm or DBS National Service History â Open Campaigns I.D. PC852 â¢ New vehicles in dealer inventory can also be identified using DBS (Sales-> Vehicle Inventory, and filter by Open Campaign). â¢ Refer to NPSB 15-460 for additional information â¢ Some vehicles may still be in transit. Please continue to check newly arriving inventory for campaign applicability. 2. Please do not drive, loan, sell or trade the specific vehicles in dealer inventory subject to this quality action. 3. Use the attached procedure to remedy any vehicles affected by this quality action prior to sale. â¢ Dealers may obtain the necessary corrugated tubing (wire conduit) and electrical tape from local sources. â¢ There is a sublet allowance for corrugated tubing and electrical tape. 4. Once remedied, dealers should submit the applicable warranty claim for the action performed to close the campaign in Service Comm and release the vehicle for sale.

PC851 2022 Pathf

Service Bulletin/Repair Instructions

Running Boards Torque Dealer Inventory ***** Dealer Announcement ***** Nissan is conducting a dealer inventory quality action to torque the bolts on the running boards to correct specification on 38 specific MY2022 Nissan Pathfinder vehicles identified in Service Comm and National Service History â Open Campaigns. The subject bolts were not torqued to specification during installation. Affected vehicles are not subject to stop sale and are either currently in dealer inventory or assigned and in transit to the dealer. ***** What Dealers Should Do ***** PLEASE FOLLOW THE ATTACHED INSTRUCTIONS: 1. Verify if vehicles are affected by this quality action using Service Comm or DBS National Service History â Open Campaigns I.D. PC851 â¢ New vehicles in dealer inventory can also be identified using DBS (Sales-> Vehicle Inventory, and filter by Open Campaign). ï§ Refer to NPSB 15-460 for additional information â¢ Please continue to check newly arriving inventory for campaign applicability. 2. Use the attached procedure to remedy any vehicles affected by this quality action prior to sale. 3. Once remedied, dealers should submit the applicable warranty claim for the action performed to close the campaign in Service Comm and release the vehicle for sale. ***** Dealer Responsibility ***** It is the dealerâs responsibility to check Service Comm or DBS National Service History â Open Campaign using the appropriate campaign I.D. for the status on each affected vehicle currently in new vehicle inventory.

P1A24 2022 Pathf

Service Bulletin/Repair Instructions

Engine Control Module (ECM) Reprogram Voluntary Service Campaign Dealer Announcement: Nissan is conducting a Voluntary Service Campaign to reprogram the Engine Control Module (ECM) seatbelt software logic on 11,656 specific MY2022 Pathfinder vehicles identified in Service Comm and DBS National Service History. The Idle Stop Start (ISS) fault message displays in the combination meter when the seat belt is not used by the driver for ten (10) consecutive ignition on/off cycles. The ECM reprogram is intended to eliminate the fault message from the driver information display. The ISS indicator lamp will remain illuminated. Normal ISS system operation will resume after the seatbelt is used. Affected vehicles are not subject to stop sale and are either currently in dealer inventory or assigned and in transit to the dealer. What Dealers Should Do: 1.Verify if vehicles are affected by this Voluntary Service Campaign using Service Comm or DBS National Service History â Open Campaigns I.D. P1A24. 2.Dealers are requested to remedy any affected vehicles in dealer new or pre-owned inventory to ensure customer satisfaction. â¢New vehicles in dealer inventory can also be identified using DBS (Sales-> Vehicle Inventory, and filter by Open Campaign). ï§Refer to NPSB15-460 for additional information â¢Please continue to check newly arriving inventory for campaign applicability. 3.Dealers should use NTB21-095 to correct any vehicles subject to this campaign. 4.Once repaired, dealers should submit the claim, using the claims coding provided, and release the vehicle.

NTB21-095

Service Bulletin/Repair Instructions

VOLUNTARY SERVICE CAMPAIGN 2022 PATHFINDER; ECM REPROGRAM FOR âISS SYSTEM FAULTâ MESSAGE INTRODUCTION Nissan is conducting this voluntary service campaign, on certain specific model year 2022 Pathfinder vehicles, to inspect and, if necessary, reprogram the ECM. This service will be performed at no charge to the customer for parts or labor. IDENTIFICATION NUMBER Nissan has assigned identification number P1A24 to this campaign. This number must appear on all communication and documentation of any nature dealing with this campaign. DEALER RESPONSIBILITY Dealers are to repair vehicles falling within range of this campaign that enter the service department. This includes vehicles purchased from private parties, vehicles presented by transient (tourists) owners, and vehicles in a dealerâs inventory.

PC841 2022 Pathf

Service Bulletin/Repair Instructions

Rear Door Hinge Bolt Voluntary Service Campaign ***** Dealer Announcement ***** Nissan has reclassified the previously announced quality action (PC817) for new vehicle inventory as a Voluntary Service Campaign. Dealers will replace one bolt on both the right and left side rear door lower hinge on 4,965 specific 2022 Pathfinder vehicles identified in Service Comm and DBS National Service History. Due to a design specification concern, the installed rear door lower hinge bolt may have insufficient thread engagement on the weld nut at the B-Pillar. This may cause the hinge bolt to become loose or may be missing. ***** What Dealers Should Do ***** 1. Verify if vehicles are affected by this Voluntary Service Campaign using Service Comm or DBS National Service History â Open Campaigns I.D. PC841. 2. Dealers are requested to remedy any affected vehicles in dealer new or pre-owned inventory to ensure customer satisfaction. â¢ New vehicles in dealer inventory can also be identified using DBS (Sales-> Vehicle Inventory, and filter by Open Campaign). ï§ Refer to NPSB15-460 for additional information â¢ Please continue to check newly arriving inventory for campaign applicability. 3. Dealers should use NTB21-091 to correct any vehicles subject to this campaign. 4. Once repaired, dealers should submit the claim, using the claims coding provided, and release the vehicle.

NTB21-091

Service Bulletin/Repair Instructions

VOLUNTARY SERVICE CAMPAIGN 2022 PATHFINDER; REAR DOOR HINGE BOLT INTRODUCTION Nissan is conducting this voluntary service campaign, on certain specific model year 2022 Pathfinder vehicles, to replace the rear hinge bolt of both the driver (LH) side and passenger (RH) side rear door lower hinges. This service will be performed at no charge to the customer for parts or labor. IDENTIFICATION NUMBER Nissan has assigned identification number PC841 to this campaign. This number must appear on all communication and documentation of any nature dealing with this campaign. DEALER RESPONSIBILITY Dealers are to repair vehicles falling within range of this campaign that enter the service department. This includes vehicles purchased from private parties, vehicles presented by transient (tourists) owners, and vehicles in a dealerâs inventory.

NTB21-079A

Service Bulletin/Repair Instructions

VOLUNTARY EMISSIONS RECALL CAMPAIGN 2022 PATHFINDER; ECM REPROGRAM This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.

NTB21-082

Service Bulletin/Repair Instructions

REAR KICKING PLATE PART CHANGE SERVICE INFORMATION The rear kicking plates have been updated to delete a rear clip. If a rear kicking plate is being replaced, use the parts listed in the PARTS INFORMATION on page 2. IMPORTANT: When replacing a rear kicking plate with an updated part, early production vehicles must have the hole for the deleted clip covered with a body patch (Figure 1), to prevent water intrusion.

R21B2 2022 Pathf

Service Bulletin/Repair Instructions

Engine Control Module (ECM) Reprogram Voluntary Emission Recall Campaign ***** Campaign Summary ***** Nissan has reclassified the previously announced quality action (PC816) for new vehicle inventory as a Voluntary Emissions Recall Campaign to reprogram the Engine Control Module (ECM) on 4,000 specific MY2022 Pathfinder vehicles identified in Service Comm and DBS National Service History. The ECM reprogram is intended to improve the Idle Stop/Start functionality after 250,000 starter operations. ***** What Dealers Should Do**** 1. Verify if vehicles are affected by this Voluntary Recall using Service Comm or DBS National Service history â Open Campaign I.D. R21B2 â¢ New vehicles in dealer inventory can also be identified using DBS (Sales-> Vehicle Inventory, and filter by Open Campaign). ï§ Refer to NPSB 15-460 for additional information â¢ Please continue to check newly arriving inventory for campaign applicability. 2. Dealers should use NTB21-079 to remedy any vehicles subject to this campaign. 3. Once remedied, dealers should submit the claim, using the claims coding provided, and release the vehicle.

NTB21-079

Service Bulletin/Repair Instructions

VOLUNTARY EMISSIONS RECALL CAMPAIGN 2022 PATHFINDER; ECM REPROGRAM INTRODUCTION Nissan is conducting this voluntary emissions recall campaign, on certain specific model year 2022 Pathfinder vehicles, to reprogram the ECM. This service will be performed at no charge to the customer for parts or labor. IDENTIFICATION NUMBER Nissan has assigned identification number R21B2 to this campaign. This number must appear on all communication and documentation of any nature dealing with this campaign. DEALER RESPONSIBILITY It is the dealerâs responsibility to check Service COMM or Dealer Business Systems (DBS) National Service History for the campaign status on each vehicle falling within the range of this voluntary emissions recall which for any reason enters the service department. This includes vehicles purchased from private parties or presented by transient (tourist) owners and vehicles in a dealerâs inventory. Failure to do so can result in civil penalties. Nissan strongly encourages dealers to correct any used vehicles in their inventory before they are retailed.

NTB21-005A

Service Bulletin/Repair Instructions

REMOTE ENGINE START This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.

NTB21-072

Service Bulletin/Repair Instructions

AC INOPERATIVE WITH DTC B20C8-14 STORED IN THE IPDM E/R IF YOU CONFIRM The AC compressor is not engaging when the AC is in the ON position, as indicated by the yellow illumination on the AC button, AND DTC B20C8-14 ECV (ELECTRICAL CONTROL VALVE) is stored in the IPDM E/R. ACTION Update the IPDM E/R to the latest software version.

NTB21-074

Service Bulletin/Repair Instructions

IDLE STOP / START SYSTEM FAULT ERROR MESSAGE SERVICE INFORMATION A âStop / Start System Faultâ error message may be displayed on the instrument panel (Figure 1), if the seatbelt remains buckled or unbuckled over 10 consecutive drive cycles. ï· Drive cycle: Driven over 2 mph, and then parked for at least 10 minutes If the Stop / Start System Fault error message is displayed on the meter, in most cases buckling / unbuckling the seat belt with the ignition ON, or in accessory mode, should clear the message. ï· If buckling / unbuckling the driverâs seatbelt does not resolve the issue, refer to the Electronic Service Manual (ESM) to diagnose and repair the vehicle, and clear the Idle Stop System (ISS) meter message.

NTB21-037A

Service Bulletin/Repair Instructions

DTCS B2E4B-06, B2E60-06, B2E61-06 STORED IN THE TCU This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

PC818 2022 Pathf

Service Bulletin/Repair Instructions

Secondary Hood Latch Dealer Inventory Dealer Announcement: Nissan is conducting a dealer inventory quality action to inspect the secondary hood latch bracket cold weld and, if necessary replace the front bumper retainer bracket on 1,373 specific MY2022 Nissan Pathfinder vehicles identified in Service Comm and National Service History â Open Campaigns. Due to a manufacturing concern, a welded plate may separate from the front bumper retainer bracket rendering the secondary hood latch inoperative. Affected vehicles are subject to stop sale and are either currently in dealer inventory or assigned and in transit to the dealer. What Dealers Should Do: PLEASE FOLLOW THE ATTACHED INSPECTION INSTRUCTIONS: 1.Verify if vehicles are affected by this quality action using Service Comm or DBS National Service History â Open Campaigns I.D. PC818 â¢New vehicles in dealer inventory can also be identified using DBS (Sales-> Vehicle Inventory, and filter by Open Campaign). ï§Refer to NPSB 15-460 for additional information â¢Please continue to check newly arriving inventory for campaign applicability. 2.Please do not drive, loan, sell or trade the specific vehicles in dealer inventory subject to this quality action. 3.Use the attached procedure to remedy any vehicles affected by this quality action prior to sale. 4.Once remedied, dealers should submit the applicable warranty claim for the action performed to close the campaign in Service Comm and release the vehicle for sale. Dealer Responsibility: It is the dealerâs responsibility to check Service Comm or DBS National Service History â Open Campaign using the appropriate campaign I.D for the inspection status on each affected vehicle currently in new vehicle inventory.

REVISION 1 - PC8

Service Bulletin/Repair Instructions

Secondary Hood Latch Dealer Inventory UPDATE July 29, 2021 Please discard earlier versions of this bulletin. The announcement from earlier this morning (July 29, 2021) has been revised to include the following: - Dealers may order parts, if needed, via DBS. Most vehicles will not require parts replacement.

PC817 2022 Pathf

Service Bulletin/Repair Instructions

Rear Door Hinge Bolt Dealer Inventory ***** Dealer Announcement ***** Nissan is conducting a dealer inventory quality action to replace one bolt on both the right and left rear door hinge on 2,143 specific MY2022 Nissan Pathfinder vehicles identified in Service Comm and National Service History â Open Campaigns. Due to a manufacturing concern, the installed rear door hinge bolt may not meet Nissanâs design specifications for the Pathfinder. Affected vehicles are subject to stop sale and are either currently in dealer inventory or assigned and in transit to the dealer. ***** What Dealers Should Do ***** PLEASE FOLLOW THE ATTACHED INSPECTION INSTRUCTIONS: 1. Verify if vehicles are affected by this quality action using Service Comm or DBS National Service History â Open Campaigns I.D. PC817 â¢ New vehicles in dealer inventory can also be identified using DBS (Sales-> Vehicle Inventory, and filter by Open Campaign). ï§ Refer to NPSB 15-460 for additional information â¢ Please continue to check newly arriving inventory for campaign applicability. 2. Please do not drive, loan, sell or trade the specific vehicles in dealer inventory subject to this quality action. 3. Use the attached procedure to remedy any vehicles affected by this quality action prior to sale. 4. Once remedied, dealers should submit the applicable warranty claim for the action performed to close the campaign in Service Comm and release the vehicle for sale.

PC816 2022 Pathf

Service Bulletin/Repair Instructions

Engine Control Module (ECM) Reprogram Dealer Inventory Campaign Summary: Nissan is conducting a dealer inventory quality action to update the Engine Control Module (ECM) software on 2,117 specific MY2022 Nissan Pathfinder vehicles identified in Service Comm and National Service History â Open Campaigns. This Engine Control Module (ECM) reprogram is intended to improve the idle stop/start (ISS) functionality. Affected vehicles are subject to stop sale and are either currently in dealer inventory or assigned and in transit to the dealer. What Dealers Should Do: PLEASE FOLLOW THE ATTACHED INSPECTION INSTRUCTIONS: 1.Verify if vehicles are affected by this quality action using Service Comm or DBS National Service History â Open Campaigns I.D. PC816 â¢New vehicles in dealer inventory can also be identified using DBS (Sales-> Vehicle Inventory, and filter by Open Campaign). ï§Refer to NPSB 15-460 for additional information â¢Please continue to check newly arriving inventory for campaign applicability. 2.Please do not drive, loan, sell or trade the specific vehicles in dealer inventory subject to this quality action. 3.Use the attached procedure to remedy any vehicles affected by this quality action prior to sale. 4.Once remedied, dealers should submit the applicable warranty claim for the action performed so it can be closed in Service Comm and release the vehicle for sale. Dealer Responsibility: It is the dealerâs responsibility to check Service Comm or DBS National Service History â Open Campaign using the appropriate campaign I.D for the inspection status on each affected vehicle currently in new vehicle inventory.

Reading this report

Complaint counts are reports filed with NHTSA, not failure rates. A common model collects more of them than a rare one that breaks more often.