Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
NTB09-131C
Service Bulletin/Repair Instructions
CERTIFICATION LABEL AND VIN PLATE REPLACEMENT SERVICE INFORMATION Because of collision damage or other vehicle repair, a replacement “Certification Label” or “VIN Plate/Label” may be needed. HINT: Certification Label = FMVSS (Federal Motor Vehicle Safety Standards) label. These items may be available from Nissan by request if certain criteria are met. This bulletin lists the criteria and provides an application form for such replacements. · The “VIN Plate/Label” (metal plate or vinyl label) is attached to the instrument panel or body on the driver side at the base of the windshield (see Figure 1). · The “Certification Label” (vinyl adhesive label) is located on the lower area of the driver side B-Pillar (see Figure 1).
NTB19-071D
Service Bulletin/Repair Instructions
DTC B00A0-00 STORED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin. IF YOU CONFIRM DTC B00A0-00 (OCCUPANT DETECTION SENSOR UNIT) is stored, AND OCS zero point reset cannot be performed, (continued on the next page)
NTB12-103I
Service Bulletin/Repair Instructions
CVT/TCM CALIBRATION DATA “WRITE” PROCEDURE This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB10-066C
Service Bulletin/Repair Instructions
CAN COMMUNICATION CODES – DIAGNOSTIC TIPS AND GUIDELINES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB13-027D
Service Bulletin/Repair Instructions
CAN COMMUNICATION – NETWORK DIAGNOSTIC FLOW CHART This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB13-107G
Service Bulletin/Repair Instructions
VEHICLE KEY NOT DETECTED / AUTHENTICATED, ENGINE WILL NOT START This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB21-106B
Service Bulletin/Repair Instructions
DTC C1A17-49 OR C2580-49 STORED IN LASER/RADAR This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB09-081K
Service Bulletin/Repair Instructions
WINDSHIELD CRACKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB13-028I
Service Bulletin/Repair Instructions
REMOVING FOREIGN MATERIAL FROM THE WINDOW GLASS This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB17-019H
Service Bulletin/Repair Instructions
WINDOW GLASS WARRANTY INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB23-018G
Service Bulletin/Repair Instructions
SOFTWARE UPDATE FOR INFOTAINMENT ISSUES This bulletin is no longer active. To access infotainment software updates via the Infotainment Software Update Utility: Select SPECIALTY TOOLS, and then select Infotainment Software Updates on the left side of ASIST. Please discard previous versions of NTB23-018.
NTB23-018F
Service Bulletin/Repair Instructions
SOFTWARE UPDATE FOR INFOTAINMENT ISSUES This bulletin is no longer active. To access infotainment software updates via the Infotainment Software Update Utility: Select SPECIALTY TOOLS, and then select Infotainment Software Updates on the left side of ASIST. HINT: Initially, the Infotainment Software Update Utility will be available only on the CONSULT PC version of ASIST. The Utility will be added to ASIST WEB at a later date. Please discard previous versions of NTB23-018.
NTB17-003F
Service Bulletin/Repair Instructions
FLUID LEAK CAUSED BY TRANSFER ASSEMBLY RIGHT SIDE DRIVE SHAFT OIL SEAL This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB21-094B
Service Bulletin/Repair Instructions
TRANSFER ASSEMBLY SEAL REPLACEMENT FOR AWD FRONT DRIVE SHAFT REMOVAL This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB08-097L
Service Bulletin/Repair Instructions
DIAGNOSIS OF VEHICLE PULL (DRIFT) AND/OR STEERING WHEEL OFF-CENTER This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB23-067
Service Bulletin/Repair Instructions
2014-2020 ROGUE & 2017-2022 ROGUE SPORT; REPLACEMENT JACKKNIFE (FLIP STYLE) KEYS SERVICE INFORMATION For the APPLIED VEHICLES listed above: ï· If the jackknife key is replaced with 80560-4BA1E, the new part provided will no longer be equipped with a key blade. ï· New service parts will have a keyless entry remote with a separate mechanical key. ï· Each vehicle can have a maximum of four (4) keys registered to the BCM. Each service part contains one (1) key and one (1) remote and will use two (2) of the available slots. ï· Follow the SERVICE PROCEDURE starting on page 2 to register the new mechanical key and remote.
NTB23-018E
Service Bulletin/Repair Instructions
SOFTWARE UPDATE FOR INFOTAINMENT ISSUES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB23-018D
Service Bulletin/Repair Instructions
SOFTWARE UPDATE FOR INFOTAINMENT ISSUES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB23-049
Service Bulletin/Repair Instructions
12 VOLT BATTERY TESTING FOR IN-SERVICE VEHICLES SERVICE INFORMATION The following Service Information lists NNA procedural recommendations for establishing good connections while performing 12V battery testing. These recommendations are expected to promote uniformity during the connection process, therefore reducing the number of incorrect âTest with DCAâ and âReplaceâ results. HINT: If 12 volt batteries are allowed to discharge for a prolonged period of time, battery life may be drastically reduced. This condition may lead to premature battery replacement and customer dissatisfaction. IMPORTANT: ï· CPX-900 is now an accepted testing tool to use along with or in place of the DSS-5000 ï· CPX-900 operating instructions are found at: https://nissancpx900.midtronics.com/ ï· DSS-5000 operating instructions are found at: https://nissandss5000.midtronics.com/ ï· DCA-8000 is now a required testing tool to be used for all warranty replacement decisions. The DCA-8000 is also a more efficient charger than previously available, and will charge any available 12 volt lead acid battery safely and accurately as long as all precautions and inputs are made correctly. The DCA-8000 operating instructions are found at: https://nissandca8000.midtronics.com/
NTB23-053
Service Bulletin/Repair Instructions
SILICONE-BASED LUBRICANT OR GREASE CAN DAMAGE ELECTRICAL COMPONENTS SERVICE INFORMATION Do not apply Silicone-based lubricants or grease to, or around, any interior electrical components. To avoid the risk of death or severe personal injury, do not directly spray Silicone-based lubricant or grease, or inadvertently overspray Silicone-based lubricant or grease onto any interior electrical components. These types of lubricants can be detrimental to the proper operation of electrical components.
NTB12-103H
Service Bulletin/Repair Instructions
CVT/TCM CALIBRATION DATA âWRITEâ PROCEDURE This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB13-107F
Service Bulletin/Repair Instructions
VEHICLE KEY NOT DETECTED / AUTHENTICATED, ENGINE WILL NOT START This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB16-003C
Service Bulletin/Repair Instructions
INTELLIGENT KEY REPLACEMENT OR SWAPPING BETWEEN VEHICLES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.
NTB23-018C
Service Bulletin/Repair Instructions
SOFTWARE UPDATE FOR INFOTAINMENT ISSUES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB03-074Q
Service Bulletin/Repair Instructions
HEADLAMP, FOG LAMP, OR REAR COMBINATION LAMP FOGGING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB12-055J
Service Bulletin/Repair Instructions
CLICKING NOISE FROM FRONT OR REAR AXLE DURING TAKE-OFF/ACCELERATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB23-018B
Service Bulletin/Repair Instructions
SOFTWARE UPDATE FOR INFOTAINMENT ISSUES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB23-018A
Service Bulletin/Repair Instructions
SOFTWARE UPDATE FOR INFOTAINMENT ISSUES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB18-050A
Service Bulletin/Repair Instructions
VOLUNTARY SERVICE CAMPAIGN 2014-2017 ROGUE; ECM REPROGRAM This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB19-071C
Service Bulletin/Repair Instructions
DTC B00A0-00 STORED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB21-106A
Service Bulletin/Repair Instructions
DTC C1A17-49 OR C2580-49 STORED IN LASER/RADAR This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB10-145B
Service Bulletin/Repair Instructions
ABS/VDC CAN DIAGNOSIS INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB23-018
Service Bulletin/Repair Instructions
SOFTWARE UPDATE FOR INFOTAINMENT ISSUES SERVICE INFORMATION When diagnosing an infotainment issue or after replacement of the AV Control Unit, it is necessary to verify the current software version of the AV Control Unit to determine if a software version update is required. Use the vehicle tables in this bulletin to determine the current software version, if the AV Control Unit requires a software version update, and which procedure to use to update the AV Control Unit. The software updates in this bulletin are to address stability improvements and âbugâ fixes. IMPORTANT: If the customer is experiencing a software related concern, refer to NTB21-038 to verify if the customer concern is a hardware or software related issue. If the concern is a software related issue, review the information in this bulletin to update the AV Control Unit as needed.
NTB09-081J
Service Bulletin/Repair Instructions
WINDSHIELD CRACKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB13-028H
Service Bulletin/Repair Instructions
REMOVING FOREIGN MATERIAL FROM THE WINDOW GLASS This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB08-097K
Service Bulletin/Repair Instructions
DIAGNOSIS OF VEHICLE PULL (DRIFT) AND/OR STEERING WHEEL OFF-CENTER This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB10-126C
Service Bulletin/Repair Instructions
WHEEL BEARING COLLISION DAMAGE This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB10-029I
Service Bulletin/Repair Instructions
ABNORMAL NOISE, VIBRATION AND/OR BINDING FEELING FROM REAR DIFFERENTIAL This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB12-055I
Service Bulletin/Repair Instructions
CLICKING NOISE FROM FRONT OR REAR AXLE DURING TAKE-OFF/ACCELERATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
REVISION 2 Rogue
Service Bulletin/Repair Instructions
CVT Warranty Extension UPDATE August 30, 2022 Please discard earlier versions of this bulletin. The announcement from June 2, 2022 has been revised to include: ⢠The voucher program ID numbers provided in the FAQ section of this dealer announcement have been changed. The new voucher program ID numbers are: ï Nissan program ID: 22N2299CVT ï INFINITI program ID: 22I2299CVT
NTB17-003E
Service Bulletin/Repair Instructions
FLUID LEAK CAUSED BY TRANSFER ASSEMBLY RIGHT SIDE DRIVE SHAFT OIL SEAL This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB21-094A
Service Bulletin/Repair Instructions
TRANSFER ASSEMBLY SEAL REPLACEMENT FOR AWD FRONT DRIVE SHAFT REMOVAL This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
Rogue Pathfinder
Service Bulletin/Repair Instructions
CVT Warranty Extension In an effort to assure customer satisfaction, demonstrate our confidence in continuously variable transmissions (CVTs), and to address customer concerns including those expressed by customers in the class actions, Nissan will extend the warranty coverage on the CVT. The warranty extension includes the CVT assembly and internal CVT components, gaskets, and seals, CVT control valve body, torque converter, cooler kit (if applicable) and reprogramming of the Transmission Control Module (TCM), on the vehicles listed in this announcement. The warranty is being extended from its original duration of 60 months/60,000 miles to 84 months/84,000 miles (whichever occurs first). Coverage of other vehicle components remains unchanged, and all other terms, conditions, limitations and exclusions of Nissanâs New Vehicle Limited Warranty continue to apply. ***** What Dealers Should Do ***** 1. If an owner contacts a dealer with a CVT concern in an owned or leased vehicle, verify warranty coverage for the specific VIN and then inform the customer of any diagnostic charges. NOTE: Some owners may have opted out of the warranty extension by excluding themselves from the class action settlement, thus it is important to check the VIN for each vehicle to verify coverage. 2. Use the appropriate Technical Service Bulletin (TSB) and/or Electronic Service Manual (ESM) to diagnose the root cause of the customer concern and identify the correct repair to resolve the customer concerns. NOTE: Dealers will need to follow the warranty process and obtain pre-approval from the Powertrain Call Center (800-973-9992, option 2) for any vehicles requiring CVT replacements when the replacement cost exceeds a Dealerâs Claims Administration/Authorization Limits (DCAL). Control valves and CVT belt and pulley kits do not require pre-authorization for repairs made under warranty.
NTB10-029H
Service Bulletin/Repair Instructions
NISSAN AWD MODELS; ABNORMAL NOISE, VIBRATION AND/OR JUDDER FROM REAR DIFFERENTIAL This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB15-083A
Service Bulletin/Repair Instructions
ENHANCED DIAGNOSTIC LOGIC FOR CVT JUDDER This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB19-071B
Service Bulletin/Repair Instructions
DTC B00A0-00 STORED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
2014-2018 Rogue
Service Bulletin/Repair Instructions
Continuously Variable Transmission (CVT) Class Action Owner Notification On March 23, 2022, the Court presiding over a class action lawsuit gave final approval to a proposed settlement under which the CVT warranty will be extended for the following vehicles: 2014-2018 Rogue 2015-2018 Pathfinder *Not including Rogue Hybrid or Pathfinder Hybrid vehicles The approved settlement and the warranty extension are expected to become effective by June 1, 2022. Additional communication will be distributed prior to the warranty extension going into effect. To be clear, for the time being there is no warranty extension, and you should proceed with CVT-related claims as outlined below in bullet point three (3) under What Dealers Should Do. ***** What Dealers Should Do ***** 1. No action is necessary at this time. Nissan will provide additional instructions prior to the effective date of the extended warranty, which is expected to be June 1, 2022. 2. If a customer contacts the dealer with a CVT concern in an owned or leased vehicle, dealers should use the appropriate Technical Service Bulletin (TSB) to diagnose the root cause of the customer concern and identify the correct repair to resolve the customer concerns. NOTE: Dealers will need to follow the warranty process and obtain pre-approval from the Powertrain Call Center (800-973-9992 Option 2) for any vehicles requiring CVT assemblies to be replaced. Valve bodies and CVT belt and pulley kits do not require pre-authorization. 3. If the vehicle is no longer covered by a powertrain or parts warranty, provide owners a repair estimate for test drive, diagnosis, and repair after consulting the goodwill guidelines available in the Assurance Product Resources Manual (APRM) or WBP/18-006.
NTB10-029G
Service Bulletin/Repair Instructions
NISSAN AWD MODELS; ABNORMAL NOISE, VIBRATION AND/OR JUDDER FROM REAR DIFFERENTIAL This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB17-003D
Service Bulletin/Repair Instructions
FLUID LEAK CAUSED BY TRANSFER ASSEMBLY RIGHT SIDE DRIVE SHAFT OIL SEAL This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB13-027C
Service Bulletin/Repair Instructions
CAN COMMUNICATION â NETWORK DIAGNOSTIC FLOW CHART This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB17-003C
Service Bulletin/Repair Instructions
FLUID LEAK CAUSED BY TRANSFER ASSEMBLY RIGHT SIDE DRIVE SHAFT OIL SEAL This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB13-097J
Service Bulletin/Repair Instructions
EVAP LEAK DTC P0442, P0455, P0456 INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB17-082E
Service Bulletin/Repair Instructions
DTC P0456 CAUSED BY EVAP LEAK AT VENT CONTROL VALVE O-RING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB16-110Q
Service Bulletin/Repair Instructions
2013-2017 ALTIMA AND 2014-2017 ROGUE; 4 CYLINDER WITH DTC P17F0, P17F1, P0776, P2813, P1715, AND/OR P0841 STORED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB17-045C
Service Bulletin/Repair Instructions
CLEANING FRONT OR REAR COMBINATION LAMP ASSEMBLIES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB99-001F
Service Bulletin/Repair Instructions
STRUT AND SHOCK ABSORBER REPLACEMENT GUIDELINES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB21-106
Service Bulletin/Repair Instructions
DTC C1A17-49 OR C2580-49 STORED IN LASER/RADAR SERVICE INFORMATION If DTC C1A17-49 or C2580-49 is stored in LASER/RADAR in the âPASTâ column: ï· Erase the DTC. ï· DO NOT replace any parts. If DTC C1A17-49 or C2580-49 is stored in LASER/RADAR in the "CURRENT" column, refer to the applicable ESM for instructions.
NTB21-094
Service Bulletin/Repair Instructions
TRANSFER ASSEMBLY SEAL REPLACEMENT FOR AWD FRONT DRIVE SHAFT REMOVAL SERVICE INFORMATION When removing the front passenger (RH) side drive shaft on an applied vehicle for any reason, transfer assembly drive shaft oil seal and dust cover seal replacement is required. Refer to the SERVICE PROCEDURE in this bulletin.
NTB15-011D
Service Bulletin/Repair Instructions
NISSANCONNECT NAVIGATION SYSTEM SOFTWARE UPDATE This bulletin has been amended. See AMENDMENT HISTORY on page 14. Please discard previous versions of this bulletin.
NTB18-055E
Service Bulletin/Repair Instructions
CVT FLUID LEVEL QUICK CHECK GAUGE This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB12-055H
Service Bulletin/Repair Instructions
CLICKING NOISE FROM FRONT OR REAR AXLE DURING TAKE-OFF/ACCELERATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB17-003B
Service Bulletin/Repair Instructions
FLUID LEAK CAUSED BY TRANSFER ASSEMBLY RIGHT SIDE DRIVE SHAFT SEAL This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB15-011C
Service Bulletin/Repair Instructions
NISSAN CONNECT NAVIGATION SYSTEM SOFTWARE UPDATE This bulletin has been amended. See AMENDMENT HISTORY on page 9. Please discard previous versions of this bulletin.
NTB13-106G
Service Bulletin/Repair Instructions
CORRECT OPERATION OF AUDIO CONTROLS AND BACK-UP CAMERA REQUIRES CONFIGURATION WITH C-III PLUS This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.
NTB13-099G
Service Bulletin/Repair Instructions
AUDIO UNIT REPLACEMENT - VEHICLES WITH COLOR DISPLAY AUDIO AND NAVIGATION SYSTEM This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin
NTB14-114B
Service Bulletin/Repair Instructions
INTELLIGENT KEY DOES NOT WORK INTERMITTENTLY This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.
NTB16-047A
Service Bulletin/Repair Instructions
2014-2016 ROGUE; INTELLIGENT KEY AND/OR ELECTRICAL ISSUES AFTER INSTALLATION OF AFTERMARKET REMOTE START This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.
NTB15-027A
Service Bulletin/Repair Instructions
2014 â 2015 ROGUE FCW SYSTEM SUPPLEMENTAL INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.
NTB17-014A
Service Bulletin/Repair Instructions
BLUETOOTH, USB, AND AUX FUNCTION DIAGNOSTIC TOOL This bulletin has been amended. See AMENDMENT HISTORY on page 3. Please discard previous versions of this bulletin.
NTB12-099E
Service Bulletin/Repair Instructions
NAVIGATION WILL NOT WORK AFTER SD MAP CARD INSTALLED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.
NTB13-085C
Service Bulletin/Repair Instructions
2014-2015 ALTIMA & 2014 ROGUE; AUDIO VISUAL SYSTEM SOFTWARE UPDATE This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB13-096C
Service Bulletin/Repair Instructions
AUDIO UNIT REPLACEMENT - NON-NAVIGATION VEHICLES WITH COLOR DISPLAY AUDIO This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.
NTB19-071A
Service Bulletin/Repair Instructions
DTC B00A0-00 STORED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB09-140C
Service Bulletin/Repair Instructions
CVT OIL LEAK DIAGNOSIS USING FLUORESCENT DYE This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB15-013f
Service Bulletin/Repair Instructions
NISSAN; PROCEDURE TO CLEAN CVT TRANSMISSION FLUID COOLERS This bulletin is no longer active. Please discard previous versions of NTB15-013. Refer to the ESM for the fluid cooler cleaning procedure.
NTB16-110p
Service Bulletin/Repair Instructions
2013-2017 ALTIMA AND 2014-2017 ROGUE; 4 CYLINDER WITH DTC P17F0, P17F1, P0776, P2813, P1715, AND/OR P0841 STORED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB99-001e
Service Bulletin/Repair Instructions
STRUT AND SHOCK ABSORBER REPLACEMENT GUIDELINES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB20-043a
Service Bulletin/Repair Instructions
2014-2020 ROGUE; AIR DUCT REPLACEMENT This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB14-105a
Service Bulletin/Repair Instructions
2014-2020 ROGUE; CARPET WET FRONT FLOOR AREA This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.
NTB12-110d
Service Bulletin/Repair Instructions
POWER BACK DOOR CALIBRATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.
NTB20-090a
Service Bulletin/Repair Instructions
2014-2020 ROGUE; HVAC BLOWER NOISY OR WATER DRIPS ON DRIVER SIDE CARPET This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB20-090
Service Bulletin/Repair Instructions
2014-2020 ROGUE; HVAC BLOWER NOISY OR WATER DRIPS ON DRIVER SIDE CARPET IF YOU CONFIRM The customer states the HVAC blower is noisy OR Water is dripping on the driver side carpet after going through a car wash. ACTION Refer to REPAIR OVERVIEW on page 2.
NTB15-026d
Service Bulletin/Repair Instructions
2014-2020 ROGUE; LACKS POWER DUE TO SNOW INGESTION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
DOR-H5Y5B-01
Service Bulletin/Repair Instructions
This SKU is a Suspension Ball Joint. The customer communication requested return of unsold inventory to inspect for the outer diameter of the ball joint housing being too small. The outer diameter being too small would prevent the part from being installed, and would therefore have no impact on the end user besides time to complete installation.
NTB10-029f
Service Bulletin/Repair Instructions
NISSAN; VIBRATION AND/OR NOISE WHEN MAKING LOW SPEED TURNS IF YOU CONFIRM There is a vibration or judder feeling from the rear of the vehicle during the following conditions: ï· When making turns ï· On dry roads ï· At low speeds (under 40 MPH) And ï· The above vibration does not occur if the Electric Controlled Coupling is electrically disconnected. NOTE: In some cases, electrically disconnecting the Electric Controlled Coupling may not eliminate the vibration as described above. In these cases, further confirm the incident by removing the rear propeller shaft and retest. If the vibration does not occur with the rear propeller shaft removed, the incident is confirmed. IMPORTANT: Tire size, brand or tread pattern mismatches can cause similar symptoms. To avoid tire related mismatch vibration, it is recommended that when tires need to be replaced, all tires are replaced at the same time with tires of the proper size, same brand and pattern. See ACTION on page 2.
NTB20-069
Service Bulletin/Repair Instructions
ROGUE AND ROGUE SPORT; VIBRATION AND/OR NOISE WHEN MAKING LOW SPEED TURNS IF YOU CONFIRM There is a vibration or judder feeling from the rear of the vehicle during the following conditions: ï· When making turns ï· On dry roads ï· At low speeds (under 40 MPH) And ï· The above vibration does not occur if the electric controlled coupling is electrically disconnected. ACTION 1. Confirm the AWD control unit part number, and replace it, if applicable. 2. Replace the electric controlled coupling for the rear final drive. 3. Perform Unit Characteristics Writing.
NTB18-033b
Service Bulletin/Repair Instructions
ACCELERATOR PEDAL VIBRATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB16-110o
Service Bulletin/Repair Instructions
2013-2017 ALTIMA AND 2014-2017 ROGUE; 4 CYLINDER WITH DTC P17F0, P17F1, P0776, P2813, P1715, AND/OR P0841 STORED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB17-003a
Service Bulletin/Repair Instructions
FLUID LEAK CAUSED BY TRANSFER ASSEMBLY RIGHT SIDE DRIVE SHAFT SEAL This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB18-055d
Service Bulletin/Repair Instructions
CVT FLUID LEVEL QUICK CHECK GAUGE This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB16-110n
Service Bulletin/Repair Instructions
2013-2017 ALTIMA AND 2014-2017 ROGUE; 4 CYLINDER WITH DTC P17F0, P17F1, P0776, P2813, P1715, AND/OR P0841 STORED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB12-055g
Service Bulletin/Repair Instructions
CLICKING NOISE FROM FRONT OR REAR AXLE DURING TAKE-OFF/ACCELERATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB15-013e
Service Bulletin/Repair Instructions
NISSAN; PROCEDURE TO CLEAN CVT TRANSMISSION FLUID COOLERS This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB19-080
Service Bulletin/Repair Instructions
2014-2020 ROGUE; NO AIR FLOW FROM VENTS DUE TO SNOW BUILD-UP IF YOU CONFIRM Or the customer states there is no air flow from any of the HVAC vents And There is snow build-up in and around the blower motor air inlet, behind the cowl. ACTION 1. Remove all snow, water, and debris from the blower motor inlet, cowl area, and where the blower motor mounts. 2. Clean or replace the blower motor as needed. 3. If the blower motor does not work on all speed settings, replace the variable blower control (fan resistor). 4. If not already equipped: Install the cowl and wiper pivot filters listed in PARTS INFORMATION on the last page of this bulletin.
White Paint Clas
Service Bulletin/Repair Instructions
White Paint Class Action Owner Notification Dealer Notification In October, owners of white Nissan Rogues produced between January 11, 2013 and April 23, 2013, will receive a notice from a settlement administrator informing them of the terms of a proposed class action settlement. The settlement, if approved by the presiding court, could extend the warranty on the paint for four years and provide a one-time full vehicle repaint (subject to a copay). Eligible owners can also obtain coverage for any reasonable and necessary rental car coverage arising from the repaint, or reimbursement of amounts previously incurred for a one-time repaint and any reasonable and necessary rental car services arising from the repaint. The settlement also provides for eligibility in Nissanâs Vehicle Purchase Program. To be clear, unless and until the proposed settlement is approved by the presiding court, there is no warranty extension or other remedy and you should proceed with paint-related claims in the ordinary course. The proposed settlement, and the associated potential warranty extension, include many terms and conditions. Rather than attempting to address questions about the proposed settlement terms from customers, Nissan recommends dealers refer customers to the website listed below. This will enable owners to receive information from appropriate sources and avoid providing incorrect and/or incomplete information to customers. The website is currently live and available to inquiring customers. ***** What Dealers Should Do ***** 1. No action is necessary at this time. Nissan will provide additional instructions once the proposed settlement is approved by the court. 2. If a customer contacts the dealer with a white paint concern and/or references this settlement notification, dealers should refer the customer to the third party administratorâs website for additional information. www.vehiclepaintsettlement.com
NTB17-028a
Service Bulletin/Repair Instructions
2014-2020 ROGUE; BLOWER MOTOR SERVICE INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB16-110m
Service Bulletin/Repair Instructions
2013-2017 ALTIMA AND 2014-2017 ROGUE; 4 CYLINDER WITH DTC P17F0, P17F1, P0776, P2813, P1715, AND/OR P0841 STORED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB19-072
Service Bulletin/Repair Instructions
TRANSMISSION RANGE SWITCH SERVICE INFORMATION SERVICE INFORMATION The transmission range switch of the APPLIED VEHICLES listed above is now available as a separate service part. If the transmission range switch of an APPLIED VEHICLE is being replaced for any reason, it must be adjusted after its replacement. ï· Refer to SERVICE PROCEDURE on page 3 for transmission range switch removal, installation, and adjustment.
NTB19-071
Service Bulletin/Repair Instructions
DTC B00A0-00 STORED IF YOU CONFIRM DTC B00A0-00 (OCCUPANT DETECTION SENSOR UNIT) is stored And OCS zero point reset cannot be performed (continued on the next page) And The following screen displays: ACTION 1. Check the Occupant Classification System (OCS) control unit using the ODS Analysis tool software. ï· Refer to SERVICE PROCEDURE on page 5. HINT: âOCSâ may also be referred to as âODSâ. 2. Perform â75-zero RESETâ.
NTB18-019a
Service Bulletin/Repair Instructions
2013-2018 ALTIMA AND 2014-2018 ROGUE; ENGINE SUPPORT TOOLS This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB18-055c
Service Bulletin/Repair Instructions
CVT FLUID LEVEL QUICK CHECK GAUGE This bulletin applies only to vehicles equipped with a Continuously Variable Transmission (CVT). This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB12-100b
Service Bulletin/Repair Instructions
CVT / TCM CALIBRATION DATA ?WRITE? PROCEDURE This bulletin applies only to vehicles equipped with a Continuously Variable Transmission (CVT). This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB12-103g
Service Bulletin/Repair Instructions
CVT / TCM CALIBRATION DATA ?WRITE? PROCEDURE This bulletin applies only to vehicles equipped with a Continuously Variable Transmission (CVT). This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB15-102b
Service Bulletin/Repair Instructions
2013-2017 ALTIMA AND 2014-2017 ROGUE; WHINE NOISE FROM CVT AT HIGHWAY SPEEDS This bulletin applies only to vehicles equipped with a QR25DE (4-cyl) engine. This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.
NTB18-055b
Service Bulletin/Repair Instructions
CVT FLUID LEVEL QUICK CHECK GAUGE This bulletin applies only to vehicles equipped with a Continuously Variable Transmission (CVT). This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.
NTB16-110L
Service Bulletin/Repair Instructions
2013-2017 ALTIMA AND 2014-2017 ROGUE; 4 CYLINDER WITH DTC P17F0, P17F1, P0776, P2813, P1715, AND/OR P0841 STORED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB13-097g
Service Bulletin/Repair Instructions
ALL MODEL YEAR 2012 AND NEWER NISSAN VEHICLES; EVAP LEAK DTC P0442, P0455, P0456 INFORMATION This bulletin does NOT apply to LEAF vehicles and Titan XD vehicles with V8 diesel engine. This bulletin has been amended. See Amendment History on the last page. Please discard previous versions of this bulletin.
NTB17-082b
Service Bulletin/Repair Instructions
NISSAN; DTC P0456 CAUSED BY EVAP LEAK AT VENT CONTROL VALVE O-RING This bulletin does NOT apply to LEAF vehicles and Titan XD vehicles with V8 diesel engine. This bulletin has been amended. See Amendment History on the last page. Please discard previous versions of this bulletin.
NTB19-001
Service Bulletin/Repair Instructions
CHASSIS CONTROL MODULE DTC INFORMATION SERVICE INFORMATION If one or more of the following Chassis Control DTCs are stored: - C1BA0-00 ? (CHASSIS CONTROL BRAKE SYSTEM) - C1B92-00 ? (BRAKE CONTROL SYSTEM) - C1B93-00 ? (ENGINE/HEV SYSTEM) - C1B94-00 ? (TRANSMISSION SYSTEM) And One or more additional DTCs, other than those above, are also stored in a control unit other than the Chassis Control Module. - Perform the diagnostic/repair procedures for the additional DTCs of the other control unit FIRST. - Refer to the Electronic Service Manual (ESM) for DTC specific diagnostic information. Do not replace the CHASSIS CONTROL MODULE (CONTROLLER ASSY-IDM) if additional DTCs are present.
NTB16-110k
Service Bulletin/Repair Instructions
2013-2017 ALTIMA AND 2014-2016 ROGUE; 4 CYLINDER WITH DTC P17F0, P17F1, P0776, P2813 OR P0841 STORED This bulletin applies only to vehicles equipped with a 4 cylinder engine. This bulletin has been amended. Please see amendment history on the last page. Please discard previous versions of this bulletin.
NTB18-083
Service Bulletin/Repair Instructions
2014 - 2019 ROGUE; SQUEAK/CREAK NOISE FROM FRONT SUSPENSION BOUND BUMPER DRIVING OVER BUMPS IF YOU CONFIRM Using the flow chart on page 2, a squeak/creak noise is heard coming from the left or right front suspension bound bumper when driving over speed bumps or similar road surfaces. NOTE: This squeak/creak noise, if it should occur, is more noticeable in cold weather. ACTION Replace the front suspension bound bumper, only on the side that is making noise. - Refer to the appropriate Electronic Service Manual (ESM) for replacement information. SUSPENSION > FRONT SUSPENSION > REMOVAL AND INSTALLATION > FRONT COIL SPRING AND STRUT > Removal and Installation. - Pages 4 - 6 in this bulletin contain helpful information to perform this procedure. - Make sure to replace the one-time-use nuts listed in the PARTS INFORMATION. - Check the front wheel alignment; adjust to factory specifications as needed. NOTE: DO NOT apply lubricant to the bound bumper to resolve this issue.
NTB17-030a
Service Bulletin/Repair Instructions
NISSAN; FUEL TANK IS EXTREMELY DIFFICULT TO FILL This bulletin applies to Titan XD vehicles with a gas engine. The update below was sent out to Regions and Dealers in August of this year. We are re-circulating this update to make regional and dealer personnel aware that we are re-notifying customers at this time.
NTB18-033a
Service Bulletin/Repair Instructions
2014 ? 2019 ROGUE; ACCELERATOR PEDAL VIBRATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
Revision 1-NEVAP
Service Bulletin/Repair Instructions
OBD II EVAP Tube Warranty Enhancement The update below was sent out to Regions and Dealers in August of this year. We are re-circulating this update to make regional and dealer personnel aware that we are re-notifying customers at this time.
NTB10-029e
Service Bulletin/Repair Instructions
NISSAN; VIBRATION AND/OR NOISE WHEN MAKING LOW SPEED TURNS This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB12-103f
Service Bulletin/Repair Instructions
CVT / TCM CALIBRATION DATA ?WRITE? PROCEDURE This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB18-055a
Service Bulletin/Repair Instructions
CVT FLUID LEVEL QUICK CHECK GAUGE This bulletin applies only to vehicles equipped with a CVT (Continuously Variable Transmission). This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB15-011b
Service Bulletin/Repair Instructions
NISSAN CONNECT NAVIGATION SYSTEM SOFTWARE UPDATE This bulletin applies only to vehicles equipped with a navigation system. This bulletin has been amended. See AMENDMENT HISTORY on page 9. Please discard previous versions of this bulletin.
NTB16-110j
Service Bulletin/Repair Instructions
2013-2017 ALTIMA AND 2014-2016 ROGUE; 4 CYLINDER WITH DTC P17F0, P17F1, P0776 OR P0841 STORED This bulletin has been amended. Please see amendment history on the last page. Please discard previous versions of this bulletin.
NTB10-029d
Service Bulletin/Repair Instructions
NISSAN; VIBRATION AND/OR NOISE WHEN MAKING LOW SPEED TURNS This bulletin applies only to vehicles equipped with AWD (All-Wheel Drive) or 4WD (4-Wheel Drive). This bulletin has been amended. The APPLIED VEHICLES and PARTS INFORMATION sections have been revised. No other changes have been made. Please discard all previous versions of this bulletin.
NTB13-077d
Service Bulletin/Repair Instructions
CVT FLUID LEVEL CHECK SERVICE INFORMATION This bulletin applies only to vehicles equipped with a Continuously Variable Transmission (CVT). This bulletin has been amended. The APPLIED VEHICLES and SERVICE INFORMATION sections have been revised. No other changes have been made. Please discard all previous versions of this bulletin.
NTB18-055
Service Bulletin/Repair Instructions
CVT FLUID LEVEL QUICK CHECK GAUGE This bulletin applies only to vehicles equipped with a Continuously Variable Transmission (CVT). SERVICE INFORMATION Special tool CVT8 Oil Level Quick Check Gauge (J-51155) is now available. Each dealer has been shipped one of these tools. Additional tools can be obtained from Tech?Mate at 1-800-662-2001. Refer to the SERVICE PROCEDURE on the next page to determine how to perform a CVT fluid quick level check.
PC633 PM827 P832
Service Bulletin/Repair Instructions
CAMPAIGN BULLETIN Engine Control Module (ECM) Reprogram Regional (NV & AZ) Voluntary Service Campaign ***** Campaign Summary***** Nissan is conducting a Regional Voluntary Service Campaign to reprogram the Engine Control Module (ECM) on affected vehicles currently registered in Nevada and Arizona. The current programming may cause the air/fuel ratio to become excessively rich resulting in engine stop under certain high temperature and high altitude conditions. In addition, Nissan is asking dealers to inspect and, if necessary, replace the Positive Crankcase Ventilation (PCV) valve on certain 2013-14 Nissan Sentra vehicles. ***** What Dealers Should Do ***** 1. Verify if vehicles are affected by this Voluntary Service Campaign using Service Comm or DBS National Service History - Open Campaign I.D. Due to the various models involved and the associated responsible manufacturing location of origin, there are three (3) separate campaign IDs with unique Campaign Bulletins for each model: - PC633 - PM827 - P8325 New vehicles in dealer inventory can be also be identified using DCS (Sales-> Vehicle Inventory, and filter by Open Campaign). - Refer to NPSB 15-460 for additional information NOTE: These campaigns are state-specific and limited to vehicles that are currently registered, or previously registered, in the state of Nevada or Arizona only. 2. Nissan requests dealers repair any affected vehicles in retailer new or pre-owned inventory to ensure customer satisfaction. 3. Dealers should use the appropriate repair bulletin for the applicable model as listed below to correct any vehicles subject to this campaign. 4. Once repaired, dealer should submit a warranty claim and release the vehicle.
NTB18-050
Service Bulletin/Repair Instructions
VOLUNTARY SERVICE CAMPAIGN 2014 ? 2017 ROGUE; ECM REPROGRAM INTRODUCTION Nissan is conducting this voluntary service campaign on certain specific model year 2014 ? 2017 Rogue vehicles that are currently registered in the states of Arizona or Nevada. The Engine Control Module (ECM) software will be reprogrammed. This service will be performed at no charge to the customer for parts or labor. IDENTIFICATION NUMBER Nissan has assigned identification number PC633 (VINs starting with 5N or JN) and P8325 (VINs starting with KN) to this campaign. This number must appear on all communication and documentation of any nature dealing with this campaign. DEALER RESPONSIBILITY Dealers are to repair vehicles falling within range of this campaign that enter the service department. This includes vehicles purchased from private parties, vehicles presented by transient (tourists) owners, and vehicles in a dealer?s inventory.
NTB16-110i
Service Bulletin/Repair Instructions
2013-2017 ALTIMA AND 2014-2016 ROGUE; 4 CYLINDER WITH DTC P0776 AND/OR P0841 AND/OR JUDDER WITH P17F0 OR P17F1 STORED This bulletin has been amended to add additional information under If You Confirm on page 1, the Claims Information and to add part numbers to Table B. No other changes have been made.
NTB13-054d
Service Bulletin/Repair Instructions
ALTIMA AND ROGUE; ENGINE TURNS OFF OR HESITATES WHEN ACCELERATING FROM A STOP DURING HOT AMBIENT TEMPERATURES (+100°F) This bulletin has been amended. Table A on page 5 has been revised. No other changes have been made. Please discard previous versions of this bulletin.
NTB13-054c
Service Bulletin/Repair Instructions
ALTIMA AND ROGUE; ENGINE TURNS OFF OR HESITATES WHEN ACCELERATING FROM A STOP DURING HOT AMBIENT TEMPERATURES (+100°F) This bulletin has been amended. Table A on page 6 has been revised. No other changes have been made. Please discard previous versions of this bulletin.
NTB03-074m
Service Bulletin/Repair Instructions
FOG LAMP AND/OR HEADLAMP FOGGING This bulletin has been amended to add Fog Lamps and modify one step in the flow chart on page 3. No other changes have been made. Please discard previous versions of this bulletin.
NTB18-033
Service Bulletin/Repair Instructions
2014 - 2018 ROGUE; ACCELERATOR PEDAL VIBRATION IF YOU CONFIRM A vibration from the accelerator pedal between 1600 - 2000 RPM. ACTION Install the new brake booster vacuum tube and hose listed in the PARTS INFORMATION section of this bulletin.
NTB17-084a
Service Bulletin/Repair Instructions
2014-2017 ROGUE AND ROGUE HYBRID; SQUEAK OR RATTLE FROM FRONT DOOR FINISHER This bulletin has been amended. The PARTS INFORMATION and CLAIMS INFORMATION sections have changed. No other changes have been made. Please discard all previous versions of this bulletin.
NTB13-107b
Service Bulletin/Repair Instructions
INTELLIGENT KEY NOT DETECTED / ENGINE WILL NOT START This bulletin has been amended to update the Applied Vehicles. No other changes were made. Please discard previous versions of this bulletin.
NTB11-044c
Service Bulletin/Repair Instructions
WHEEL BALANCING SERVICE INFORMATION This bulletin has been amended. The publication date has been revised to include the latest models and model years. No other changes have been made. Please discard previous versions of this bulletin.
NTB16-110h
Service Bulletin/Repair Instructions
2013-2017 ALTIMA AND 2014-2016 ROGUE; 4 CYLINDER WITH DTC P0776 AND/OR JUDDER WITH P17F0 OR P17F1 STORED This bulletin applies only to Altima vehicles equipped with a 4 cylinder engine. This bulletin has been amended to add additional information under NOTE on page 1. No other changes have been made. Please discard previous versions of this bulletin.
NTB18-019
Service Bulletin/Repair Instructions
2013-2018 ALTIMA AND 2014-2018 ROGUE; ENGINE SUPPORT TOOLS SERVICE INFORMATION A new Engine Support Tool and Engine Support Bracket are now available to allow the CVT to be removed from the Applied Vehicles without having to remove the engine. The procedures in this bulletin are different than those that are currently in the Electronic Service Manual (ESM), which will be updated with this information at a later date. Please refer to the vehicle specific service procedure to use these new tools: Altima Page 2 Rogue AWD Page 11 Rogue FWD Page 24
NTB13-054b
Service Bulletin/Repair Instructions
ALTIMA AND ROGUE; ENGINE TURNS OFF OR HESITATES WHEN ACCELERATING FROM A STOP DURING HOT AMBIENT TEMPERATURES (+100°F) This bulletin has been amended. The APPLIED VEHICLES section and Table A on pages 5 and 6 have been revised. No other changes have been made. Please discard previous versions of this bulletin.
NTB16-110g
Service Bulletin/Repair Instructions
2013-2017 ALTIMA AND 2014-2016 ROGUE; 4 CYLINDER WITH DTC P0776 AND/OR JUDDER WITH P17F0 OR P17F1 STORED This bulletin applies to Altima vehicles equipped with a 4-cyl engine only. This bulletin has been amended to add 2013-2014 Altima to the Applied Vehicles and Table A on page 80, and to supersede NTB15-084 and NTB15-086. The Service Procedure was updated on page 81. No other changes have been made. Please discard previous versions of this bulletin.
NTB16-110f
Service Bulletin/Repair Instructions
2015-2017 ALTIMA AND 2014-2016 ROGUE; 4 CYLINDER WITH DTC P0776 AND/OR JUDDER WITH P17F0 OR P17F1 STORED This bulletin applies to Altima vehicles with a 4 cylinder engine only. This bulletin has been amended. Changes were made on pages 2, 3, 85-89 and 96. Please discard previous versions of this bulletin. You must read the entire bulletin to properly perform this repair; includes TCM reprograming.
NTB16-110e
Service Bulletin/Repair Instructions
2015-2017 ALTIMA AND 2014-2016 ROGUE; 4 CYLINDER WITH DTC P0776 AND/OR JUDDER WITH P17F0 OR P17F1 STORED This bulletin applies to Altima vehicles equipped with a 4-cylinder engine only. This bulletin has changed. You must read the entire bulletin to properly perform this repair. Please discard previous versions of this bulletin.
NTB17-108
Service Bulletin/Repair Instructions
2008-2013 ROGUE AND 2014-2015 ROGUE SELECT; RUST AROUND REAR LICENSE LAMP FINISHER IF YOU CONFIRM Rust is found on the rear deck lid surface in the area surrounding the license lamp finisher (Figure 1) or when replacing the license lamp finisher for any reason. ACTION - Replace the license lamp finisher with the new replacement part listed the Parts Information. > Refer to the Electronic Service Manual (ESM), section EXT ? Exterior for removal and installation information. - Repair any damaged surfaces that were in direct contact with the license lamp finisher.
NTB11-044b
Service Bulletin/Repair Instructions
WHEEL BALANCING SERVICE INFORMATION This bulletin has been amended. The publication date has been revised to include the latest models and model years. No other changes have been made. Please discard previous versions of this bulletin.
NTB17-080a
Service Bulletin/Repair Instructions
2014-2016 ROGUE; ROUGH IDLE ON START UP This bulletin has been amended. Table A has been updated. No other changes have been made. Please discard previous versions of this bulletin.
NTB15-084D
Service Bulletin/Repair Instructions
2013-2014 ALTIMA AND 2014-2016 ROGUE; CVT JUDDER AND DTC P17F0 OR P17F1 STORED This bulletin applies only to Altima vehicles equipped with a 4-cylinder engine. This bulletin has been amended to change the Applied Vehicles. No other changes have been made. Please discard all previous versions of this bulletin.
NTB17-007c
Service Bulletin/Repair Instructions
2014 ? 2016 ROGUE; OCCUPANT CLASSIFICATION SYSTEM RETROFIT This bulletin has been amended. Pages 15 and 17 have been revised. No other changes have been made. Please discard all previous versions of this bulletin.
NTB13-077c
Service Bulletin/Repair Instructions
CVT FLUID LEVEL CHECK SERVICE INFORMATION This bulletin applies only to vehicles equipped with a Continuously Variable Transmission (CVT). This bulletin has been amended. The APPLIED VEHICLES section has been revised. No other changes have been made. Please discard all previous versions of this bulletin.
NTB17-082a
Service Bulletin/Repair Instructions
NISSAN; DTC P0456 CAUSED BY EVAP LEAK AT VENT CONTROL VALVE O-RING This bulletin has been amended. The APPLIED VEHICLES and CLAIMS INFORMATION sections have been revised. No other changes have been made. Please discard previous versions of this bulletin.
NTB13-054a
Service Bulletin/Repair Instructions
ALTIMA AND ROGUE; ENGINE TURNS OFF OR HESITATES WHEN ACCELERATING FROM A STOP DURING HOT AMBIENT TEMPERATURES (+100°F) This bulletin has been amended. The APPLIED VEHICLES and IF YOU CONFIRM sections, as well,as Table A on page 5 have been revised. Please discard all previous versions of this bulletin.
NTB17-007b
Service Bulletin/Repair Instructions
2014 ? 2016 ROGUE; OCCUPANT CLASSIFICATION SYSTEM RETROFIT This bulletin has been amended. The CLAIMS INFORMATION section has been revised and a minor correction was made to the APPLIED VEHICLES section. No other changes have been made. Please discard all previous versions of this bulletin.
NTB17-091
Service Bulletin/Repair Instructions
2013-2017 ALTIMA AND 2014-2017 ROGUE; MIL ON WITH DTC P2004 STORED IF YOU CONFIRM MIL is ON with P2004 (INTAKE MANIFOLD RUNNER CONTROL VALVE POSITION SENSOR) stored. And There are no drivability issues. ACTION 1. Remove the intake manifold. 2. Replace the intake manifold runner control valve position sensor. 3. Re-install intake manifold.
NTB15-045e
Service Bulletin/Repair Instructions
2014-2017 ROGUE; MANUAL HVAC IMPROPER OPERATION This bulletin has been amended. Changes have been made on pages 1 and 2. No other changes have been made. Please discard all previous versions.
NTB17-084
Service Bulletin/Repair Instructions
2014-2017 ROGUE AND ROGUE HYBRID; SQUEAK OR RATTLE FROM FRONT DOOR FINISHER IF YOU CONFIRM While driving, a squeak noise is heard from either front door finisher in the areas shown in Figure 1, and The noise stops when the area is pressed, and The VIN begins with 5N1. or The VIN begins with KNM and was built before KNMAT2M(**)GP 605885 // October 1, 2015. AND/OR A rattle noise is heard when either front door outside handle is operated, and The VIN begins with 5N1 and was built before 5N1AT2M(**)HC 830035 // May 1, 2017. ACTION - If applicable, apply felt tape to repair front door finisher squeak noise. See page 2. - If applicable, apply felt tape to repair front door handle noise. See page 4.
NTB17-080
Service Bulletin/Repair Instructions
2014-2016 ROGUE; ROUGH IDLE ON START UP IF YOU CONFIRM Under the conditions listed below, when the engine is started it runs rough (rough idle) for a few seconds, and then will idle normally: - Ambient temperature is between 25°F and 45°F (-4°C - 7°C). - The engine has been OFF (not running) long enough for the engine be to close to the same temperature as the ambient temperature (about 6 hours). NOTE: This bulletin does not apply to the following issues: - Engine does not start. - Engine has a long crank time before starting. ACTION 1. Refer to step 6 in the SERVICE PROCEDURE to confirm this bulletin applies to the vehicle you are working on. 2. If this bulletin applies, reprogram the ECM.
NTB15-026c
Service Bulletin/Repair Instructions
2014-2017 ROGUE; LACKS POWER DUE TO SNOW INGESTION This bulletin has been amended. Changes have been made on pages 1 ? 5 and in the Parts Information. Please discard previous versions of this bulletin.
NTB12-055f
Service Bulletin/Repair Instructions
CLICKING NOISE FROM FRONT OR REAR AXLE DURING TAKE-OFF/ACCELERATION This bulletin has been amended. The APPLIED VEHICLES section has been revised. No other changes have been made. Please discard previous versions of this bulletin.
NTB15-062c
Service Bulletin/Repair Instructions
2014-2016 ROGUE; POPPING NOISE FROM FRONT SUSPENSION WHEN TURNING This bulletin has been amended to emphasize replacement of all the parts listed in the Parts Information. Please discard previous versions of this bulletin.
NTB12-103e
Service Bulletin/Repair Instructions
CVT / TCM CALIBRATION DATA "WRITE" PROCEDURE This bulletin does not apply to Pathfinder Hybrid, Murano Hybrid or Rogue Hybrid This bulletin has been amended. APPLIED VEHICLES has been updated. SERVICE INFORMATION has been amended. A REPAIR TABLE has been added. Procedural steps have been added to SERVICE PROCEDURE. Discard all previous versions of this bulletin.
NTB15-013d
Service Bulletin/Repair Instructions
NISSAN; PROCEDURE TO CLEAN CVT TRANSMISSION FLUID COOLERS This bulletin has been amended. The APPLIED VEHICLES section has been revised. No other changes have been made. Please discard previous versions of this bulletin.
NTB15-084c
Service Bulletin/Repair Instructions
2013-2016 ALTIMA AND 2014-2016 ROGUE; CVT JUDDER AND DTC P17F0 OR P17F1 STORED This bulletin does not apply to Rogue Select or Altima with 6-cylinder engine. This bulletin has been amended. The PARTS INFORMATION section has been revised. No other changes have been made. Please discard all previous versions of this bulletin.
NTB15-086g
Service Bulletin/Repair Instructions
2013-2014 ALTIMA AND 2014-2016 ROGUE; MIL ON WITH DTC P0776, P1715 MAY HAVE HESITATION AND/OR LACK OF POWER This bulletin applies only to Altima vehicles equipped with 4-cylinder engine. This bulletin has been amended. The PARTS INFORMATION section has been revised. No other changes have been made. Please discard all previous versions of this bulletin.
NTB15-087a
Service Bulletin/Repair Instructions
CVT WITH 4 CYLINDER ENGINE VALVE BODY REPLACEMENT WITH CONFIRMED DTC This bulletin has been amended. Changes have been made throughout. Please discard previous versions of this bulletin.
NTB17-030
Service Bulletin/Repair Instructions
NISSAN; FUEL TANK IS SLOW OR DIFFICULT TO FILL IF YOU CONFIRM The fuel tank is slow or difficult to fill (filling nozzle shuts off before tank is full). IMPORTANT: Make sure this incident has been duplicated at a gas station by dealer service staff. ACTION Perform the Service Procedure in this bulletin, starting on the next page.
NTB17-028
Service Bulletin/Repair Instructions
2014-2017 ROGUE; BLOWER MOTOR SERVICE INFORMATION SERVICE INFORMATION When diagnosing the operation of the heating and cooling system's blower motor, make sure there is no interference from other personal devices before replacing any parts or performing any repairs. All personal devices (12V charger, USB charger, PC charger, etc.) must be unplugged/removed from the vehicle when diagnosing/verifying the customer issue related to blower motor operation.
NTB17-022
Service Bulletin/Repair Instructions
2014-2017 ROGUE; ENGINE AIR CLEANER CASE DUCT SERVICE INFORMATION SERVICE INFORMATION When removing and installing the engine air cleaner case duct (case duct) in an APPLIED VEHICLE for any reason, use the information in this bulletin in addition to the procedure in the EM-Engine Mechanical section of the Electronic Service Manual (ESM).
NTB15-086f
Service Bulletin/Repair Instructions
2013-2014 ALTIMA AND 2014-2016 ROGUE; MIL ON WITH DTC P0776, P1715 MAY HAVE HESITATION AND/OR LACK OF POWER This bulletin applies to Rogue and Altima vehicles equipped with 4-cylinder engines only This bulletin has been amended to change the information under the NOTE on page 1, with no other changes made to the body of this bulletin. Please discard previous versions of this bulletin.
NTB14-068b
Service Bulletin/Repair Instructions
POWER MOONROOF INITIALIZATION SERVICE INFORMATION This bulletin has been amended. The APPPLIED VEHICES section and step 3 on page 3 have been revised. No other changes have been made. Please discard all previous versions.
PC490OL
Service Bulletin/Repair Instructions
Nissan is conducting a voluntary service campaign to reprogram the Continuously Variable Transmission (CVT) software on specific 2014-16 L33 Altima and 2014-2016 Rogue vehicles
NTB17-007a
Service Bulletin/Repair Instructions
2014 2016 ROGUE OCCUPANT CLASSIFICATION SYSTEM RETROFIT This bulletin has been amended. The Parts Informatioin and Applied Vehicles have been corrected. No other changes have been made. Please discard previous versions of this bulletin.
NTB17-007
Service Bulletin/Repair Instructions
2014 - 2016 ROGUE OCCUPANT CLASSIFICATION SYSTEM RETROFIT SERVICE INFORMATION The information in this bulletin is provided for customers who have concerns with their Occupant Classification System (OCS) operation after all campaigns have been completed. Follow the steps in this bulletin to determine if this OCS retrofit procedure is applicable to the vehicle you are working on. DETERMINE IF OCS RETROFIT APPLIES 1. Check Service COMM to confirm if OCS reprogramming campaign has been completed (R1609 / NTB16-052). Completed: - Write on the repair order the date it was completed and by which dealer. - Go to step 2. Not Completed: - Complete campaign R1609 / NTB16-052. - No further action needed. OCS retrofit does NOT apply.
REVISION 1 - PC4
Service Bulletin/Repair Instructions
CVT Reprogramming Voluntary Service Campaign The announcement from December 9th, 2016 has been revised to include: - Campaign repair bulletin, NTB16-121, on ASIST has been revised to include instructions for using special tool MTS 6513. If using the attachments on NNAnet, Dealer360, or this email, please be aware that the "Click Here" function on page 2 will not link to the MTS 6513 instructions. It has been attached as a separate document for your convenience. Please discard earlier versions of this bulletin.
NTB16-121a
Service Bulletin/Repair Instructions
VOLUNTARY SERVICE CAMPAIGN 2013-2016 ALTIMA AND 2014-2016 ROGUE; TCM REPROGRAMMING This bulletin has been amended. A link for using the BOSCH MTS 6513 to perform the reprogramming has been added. No other changes have been made. Please discard previous versions of this bulletin.
NTB17-003
Service Bulletin/Repair Instructions
PATHFINDER, MURANO, AND ROGUE; FLUID LEAK CAUSED BY TRANSFER ASSEMBLY RIGHT SIDE DRIVE SHAFT SEAL This bulletin applies only to AWD equipped vehicles. IF YOU CONFIRM Fluid is leaking from the right side of the transfer assembly (see Figure 1). NOTE: The fluid leak is not caused by the seal shown in Figure 1. ACTION 1. DO NOT REPLACE the transfer assembly. 2. Reseal the transfer assembly. - Refer to the Electronic Service Manual (ESM), section DLN ? Driveline, for transfer assembly removal, reseal, and installation information. - Refer to page 2 and 3 for additional information. CAUTION: Be careful not to damage the transfer assembly right side drive shaft seal when reinstalling the drive shaft.
NTB12-110c
Service Bulletin/Repair Instructions
POWER BACK DOOR CALIBRATION This bulletin has been amended. Step 15 has been revised. No other changes have been made. Please discard previous versions of this bulletin.
NTB12-110b
Service Bulletin/Repair Instructions
POWER BACK DOOR CALIBRATION The Applied Vehicles in this bulletin have been amended. No other changes have been made Please discard previous versions of this bulletin.
NTB14-059b
Service Bulletin/Repair Instructions
2011-2017 LEAF; REPLACEMENT HIGH VOLTAGE BATTERY PACK This bulletin has been amended. The Applied Vehicles and Parts Information have been revised. No other changes have been made. Please discard previous versions of this bulletin.
NTB15-048a
Service Bulletin/Repair Instructions
2014-2017 ROGUE; VIBRATION IN STEERING WHEEL OR PASSENGER FRONT SEAT AT IDLE This bulletin has been amended to add model years and to remove any reference to the A/C. Please discard previous versions of this bulletin.
PC490 - 2013-16
Service Bulletin/Repair Instructions
CVT Reprogramming Voluntary Service Campaign ***** Campaign Summary***** Nissan is conducting a voluntary service campaign on approximately 1,657,666 specific MY2013-16 Altima (L33) and MY2014-16 Rogue (T32) vehicles to reprogram the Continuously Variable Transmission (CVT) software. Under specific driving conditions, hydraulic pressure may decrease and result in belt slip within the CVT. This may result in MIL illumination (P0776) and poor acceleration in some vehicles. There is no safety concern due to built-in fail-safe logic. Nissan is proactively reprogramming the CVT to prevent durability concerns and high out of warranty repair costs for owners. ***** What Dealers Should Do ***** 1. Verify if vehicles are affected by this Voluntary Service Campaign using Service Comm I.D. PC490. 2. Dealers are requested to repair any affected vehicles in dealer new or pre-owned inventory to ensure customer satisfaction. 3. Dealers should use NTB16-121 to correct any vehicles subject to this campaign. 4. Once repaired, dealers should submit the claim, using the claims coding provided, and release the vehicle.
NTB16-121
Service Bulletin/Repair Instructions
VOLUNTARY SERVICE CAMPAIGN 2013-2016 ALTIMA AND 2014-2016 ROGUE; TCM REPROGRAMMING INTRODUCTION Nissan is conducting this voluntary service campaign to reprogram the Transmission Control Module (TCM) for the transmission on certain specific 2013-2016 Altima and 2014-2016 Rogue vehicles. This TCM reprogram will be performed at no charge for parts or labor. IDENTIFICATION NUMBER Nissan has assigned identification number PC490 to this campaign. This number must appear on all communications and documentation of any nature dealing with this campaign. DEALER RESPONSIBILITY Dealers are to repair vehicles falling within range of this campaign that enter the service department. This includes vehicles purchased from private parties, vehicles presented by transient (tourists) owners, and vehicles in a dealer?s inventory.
NTB13-107a
Service Bulletin/Repair Instructions
INTELLIGENT KEY NOT DETECTED / ENGINE WILL NOT START This bulletin has been amended to update the Applied Vehicles and make changes to the body of the bulletin. Please discard previous versions.
NTB16-116
Service Bulletin/Repair Instructions
NISSAN; DIAGNOSIS INFORMATION FOR ABS DTC C1130 SERVICE INFORMATION When diagnosing for DTC C1130 (ENGINE SIGNAL): ECM related DTCs (P-codes) must be diagnosed, repaired, and DTCs erased first. - DTC C1130 is an ABS DTC that indicates an output signal of the ECM is not recognized. - Absent or incorrect ECM signals, that are indicated by corresponding P-codes, may trigger C1130 in the ABS control unit. - Some vehicle features that can be affected by absent or incorrect ECM signals are: - Forward Emergency Braking (FEB) - Intelligent Cruise Control (ICC) - VDC/ABS/TCS
NTB15-045d
Service Bulletin/Repair Instructions
2014-2017 ROGUE; MANUAL HVAC IMPROPER OPERATION This bulletin has been amended. Changes have been made throughout. Please discard all previous versions.
NTB15-086e
Service Bulletin/Repair Instructions
2013-2014 ALTIMA AND 2014-2016 ROGUE; MIL ON WITH DTC P0776, P1715 MAY HAVE HESITATION AND/OR LACK OF POWER This bulletin has been amended to remove 2015-2016 Altima from the Applied Vehicles. Please discard previous versions of this bulletin.
NTB15-062b
Service Bulletin/Repair Instructions
2014-2016 ROGUE; POPPING NOISE FROM FRONT SUSPENSION WHEN TURNING This bulletin has been amended throughout. Discard all previous versions of this bulletin.
NTB13-077b
Service Bulletin/Repair Instructions
CVT FLUID LEVEL CHECK SERVICE INFORMATION This bulletin has been amended. The APPLIED VEHICLES section has been revised. No other changes have been made. Please discard all previous versions of this bulletin.
NTB16-092
Service Bulletin/Repair Instructions
NISSAN; DOORS DIFFICULT TO CLOSE WITH TEMPERATURE BELOW FREEZING IF YOU CONFIRM: THE FOLLOWING INCIDENT, OR THE CUSTOMER REPORTS THIS INCIDENT: - THE VEHICLE HAS BEEN SETTING (NOT RUNNING) IN TEMPERATURES BELOW 14°F (-10°C) FOR AN EXTENDED PERIOD (SUCH AS OVERNIGHT). THEN - A SIDE DOOR IS OPENED. THEN - THE DOOR IS DIFFICULT TO CLOSE/LATCH, WILL NOT CLOSE/LATCH WITH NORMAL PRESSURE; REQUIRES ADDITIONAL EFFORT TO CLOSE/LATCH, OR THE DOOR MAY ONLY LATCH HALF WAY. THEN - THE DOOR WILL CLOSE/LATCH NORMALLY WHEN THE VEHICLE HAS WARMED UP (VEHICLE LEFT IN THE SUN, MOVED INDOORS, OR DRIVEN FOR SEVERAL MINUTES). NOTE: O THE ABOVE INCIDENT DOES NOT APPLY TO SLIDING SIDE DOORS OR A REAR HATCH (BACK DOOR). O THE ABOVE INCIDENT, IF IT SHOULD OCCUR, COULD BE CONFIRMED OR REPORTED FOR ONE OR MORE SIDE DOORS. ACTION REPLACE THE DOOR LOCK FOR THE AFFECTED DOOR. - DO NOT REPLACE ALL SIDE DOOR LOCKS AUTOMATICALLY. REPLACE ONLY THE DOOR LOCK OF THE DOOR(S) WITH THE INCIDENT AS DESCRIBED UNDER IF YOU CONFIRM. - REFER TO THE ELECTRONIC SERVICE MANUAL (ESM), SECTION DLK DOOR & LOCK FOR REPLACEMENT PROCEDURE.
NTB12-057C
Service Bulletin/Repair Instructions
ALTIMA, SENTRA, AND ROGUE; CVT FAIL-SAFE CONDITION SERVICE INFORMATION THIS BULLETIN HAS BEEN AMENDED. THE APPLIED VEHICLES SECTION HAS BEEN REVISED. NO OTHER CHANGES HAVE BEEN MADE. PLEASE DISCARD PREVIOUS VERSIONS OF THIS BULLETIN.
NTB16-090
Service Bulletin/Repair Instructions
2011-2015 ROGUE AND ROGUE SELECT; REDUCED PERFORMANCE DUE TO CVT FLUID TEMPERATURE PROTECTION LOGIC IF YOU CONFIRM THE VEHICLE SPEED IS, OR WAS, REDUCED BY THE CVT FAIL-SAFE (REDUCED VEHICLE SPEED) AFTER CONTINUOUS OPERATION UNDER THE FOLLOWING CONDITIONS: - HIGH RPM AND/OR HIGH SPEED DRIVING (RPM OF 4000+ OR SPEEDS OF 65 MPH [104.6 KM/H] FOR 1.0 1.5 HRS. OR MORE) - DRIVING IN AMBIENT TEMPERATURE OF 96 DEGREES OR HIGHER - CLIMBING STEEP OR EXTENDED HILLS FOR 6 MILES (9.6 KM) OR MORE - WHINE OR RATTLE TYPE NOISE OCCURRING DURING REDUCED ENGINE PERFORMANCE (VEHICLE SPEED DECREASE) NOTE: BEFORE APPLYING THIS BULLETIN, CHECK FOR AND REPAIR ANY DTCS FIRST. ACTION 1. PERFORM SELF-DIAGNOSIS WITH CONSULT-III PLUS (C-III PLUS). - IF DTCS ARE PRESENT, REFER TO THE APPROPRIATE SECTION OF THE ELECTRONIC SERVICE MANUAL (ESM) AND DIAGNOSE THE DTCS FIRST BEFORE PROCEEDING TO STEP 2 BELOW. 2. CHECK THE NUMBER OF COUNTS OF "CVT-A WITH C-III PLUS. - REFER TO THE FLOW CHART ON PAGE 2 AND THE SERVICE PROCEDURE STARTING ON PAGE 3 TO CONFIRM IF THIS BULLETIN APPLIES.
NTB15-045C
Service Bulletin/Repair Instructions
2014-2016 ROGUE; MANUAL HVAC IMPROPER OPERATION MANUAL HVAC SYSTEM ONLY IF YOU CONFIRM THERE ARE NO HVAC DTCS STORED, AND ONE OF THE FOLLOWING CONDITIONS IS OCCURRING: - AIR TEMPERATURE FROM THE HVAC VENTS DOES NOT MATCH THE TEMPERATURE SETTING (WARM AIR IS DISCHARGED WHEN COLD IS SELECTED, OR VICE VERSA). OR - AIR IS DISCHARGED FROM THE INCORRECT LOCATION. FOR EXAMPLE, VENT IS SELECTED BUT 100% OF AIR IS DISCHARGED TO THE FOOT OR DEFROST. NOTE: IF HVAC DTC(S) ARE STORED, THIS BULLETIN DOES NOT APPLY. REFER TO THE ELECTRONIC SERVICE MANUAL FOR FURTHER INFORMATION. ACTION USE CONSULT-III PLUS (C-III PLUS) TO PERFORM DOOR MOTOR STARTING POSITION RESET.
NTB15-086D
Service Bulletin/Repair Instructions
2013-2016 ALTIMA AND 2014-2016 ROGUE; MIL ON WITH DTC P0776, P1715 MAY HAVE HESITATION AND/OR LACK OF POWER ALTIMA WITH 4-CYLINDER ENGINE ONLY THIS BULLETIN HAS BEEN AMENDED. THE TITLE IS CHANGED, A DTC IS ADDED UNDER IF YOU CONFIRM, AND TCM REPROGRAMMING IS ADDED TO THE SERVICE PROCEDURE. PLEASE DISCARD PREVIOUS VERSIONS OF THIS BULLETIN.
NTB13-097D
Service Bulletin/Repair Instructions
ALL MODEL YEAR 2012 AND NEWER NISSAN VEHICLES; EVAP LEAK DTC P0442, P0455, P0456 INFORMATION THIS BULLETIN HAS BEEN AMENDED. THE TITLE HAS BEEN REVISED, AND THE BULLETIN NOW INCLUDES VEHICLES IN PRODUCTION AS OF THE DATE OF THIS UPDATE. NO OTHER CHANGES HAVE BEEN MADE. PLEASE DISCARD ALL PREVIOUS VERSIONS OF THIS BULLETIN.
NTB14-024C
Service Bulletin/Repair Instructions
20162014-2016 ROGUE; IPDM CONFIGURATION AFTER UNIT REPLACEMENT THIS BULLETIN HAS BEEN AMENDED. TWO PART NUMBER TABLES, AND SYMPTOMS THAT COULD OCCUR IF THE IPDM IS NOT CONFIGURED HAVE BEEN ADDED, AND THE APPLIED VEHICLES SECTION HAS BEEN REVISED. PLEASE DISCARD PREVIOUS VERSIONS OF THIS BULLETIN. SERVICE INFORMATION AFTER REPLACING AN IPDM IN AN APPLIED VEHICLE, THE IPDM ECU PART NUMBER MUST BE SELECTED FOR PROPER FUNCTION. USE CONSULT-III PLUS (C-III PLUS) THROUGH MANUAL CONFIGURATION TO DO THIS. THE SETTING IS BASED ON THE VEHICLE OPTIONS (SEE TABLE A, B OR C ON PAGE 2 FOR VEHICLE OPTIONS). -THE IPDM E/R PART NUMBER IS EXTERNALLY MARKED ON ALL IPDM E/R CASES AND DOES NOT INDICATE WHAT IT IS CONFIGURED AS. -ONCE CONFIGURED, THE CONFIGURED NUMBER CAN ONLY BE READ THROUGH READ / WRITE CONFIGURATION. -IPDM E/R CONFIGURATION CANNOT BE READ THROUGH WORK SUPPORT / ECU IDENTIFICATION AND WILL ONLY SHOW THE PART NUMBER THAT IS MARKED ON THE OUTSIDE OF THE CASE. -THE VEHICLE WILL NOT START UNTIL THE IPDM IS CONFIGURED. IF THE IPDM IS CONFIGURED INCORRECTLY FOR THE VEHICLES OPTIONS, THE SYMPTOMS SHOWN BELOW MAY OCCUR.
NTB11027B
Service Bulletin/Repair Instructions
SERVICE INFORMATION Temporary tire Flat Spotting is common on New Dealer In-Stock vehicles that have not been occasionally moved. Flat Spotting can occur after the vehicle has been parked (not moved) for a few days, or longer. In most cases it is temporary. In extreme cases it can be permanent. Vehicles should be moved every 30 days, in one direction only, enough to rotate the tires 90° (see Figure 1). Moving vehicles as shown will prevent tire Flat Spotting. See this bulletin for further detail.
NTB12103D
Service Bulletin/Repair Instructions
SERVICE INFORMATION The Service Procedure (starting on page 2) in this bulletin contains the steps to perform TCM Calibration Data Write Procedures. These procedures are used when a complete CVT is replaced, or a CVT control valve (valve body) is replaced, or a Transmission Control Module (TCM) is replaced. See this bulletin for further detail.
NTB15026B
Service Bulletin/Repair Instructions
IF YOU CONFIRM An Applied Vehicle experiences reduced power during extremely heavy snow fall, and snow is found inside the air cleaner case. NOTE: The MIL may be ON with DTC P0101 (MAF SEN/CIRCUIT B1) stored. ACTION See Repair Flow Chart on page 2 to confirm that this bulletin applies. See this bulletin for further detail.
NTB15013C
Service Bulletin/Repair Instructions
IMPORTANT: Metal debris and friction material may become trapped in the radiator, cooling hoses, bypass valve or external CVT fluid cooler. This debris can contaminate the newly serviced transmission, control valve or torque converter. In severe cases this debris can block or restrict flow and may cause damage to the newly serviced CVT. SERVICE INFORMATION When a CVT, control valve or torque converter replacement is necessary for one of the applied vehicles, the CVT transmission fluid coolers (radiator based fluid cooler and external auxiliary cooler if present) must be flushed. Please see this bulletin for further details.
NTB15087
Service Bulletin/Repair Instructions
IF YOU CONFIRM One or more of the DTCs listed in Table A are stored in the Transmission Control Module (TCM). And No other DTCs are stored other than what are listed in Table A. And The diagnostic procedures in the Electronic Service Manual (ESM) for each DTC in Table A, that is stored in the TCM, has been performed and indicates that the CVT assembly must be replaced. NOTE: Do not replace the CVT. ACTION Replace the CVT valve body assembly (control valve) with a unit from Parts Information. See page 2 for important information when replacing the CVT control valve.
NTB15113A
Service Bulletin/Repair Instructions
IF YOU CONFIRM The following, or the customer reports the following: - Intermittently there is low power when accelerating, And/or - The stop lamps (brake lights) stay ON after releasing the brake pedal, with the ignition ON or OFF. ACTION - Delete the stop lamp relay and bypass the stop lamp relay circuit. - Replace the stop lamp switch with the one listed in PARTS INFORMATION. See this bulletin for further detail.
NTB16047
Service Bulletin/Repair Instructions
SERVICE INFORMATION Changes or modifications to the vehicle electrical system (including the installation of aftermarket remote-start devices) may affect the proper operation of the vehicle electrical systems. Installation of aftermarket remote-start devices may cause Intelligent Keys to not register, buttons in the Intelligent Key to not operate, and other electrical system related issues. See this bulletin for further detail.
NTB15110A
Service Bulletin/Repair Instructions
IF YOU CONFIRM * The key cannot be removed from the ignition. And/or * The Shifter will not move out of park. NOTE: For Rogue (T32), it is possible that shifter selector knob may not be installed correctly. Please refer to NTB14-058 for shift selector knob service information before applying this bulletin. ACTION a. Adjust the key interlock cable. b. Adjust the stop lamp switch. NOTE: Nissan vehicle warranty does not cover incidents due to lack of vehicle maintenance and/or physical damage. Refer to New Vehicle Limited Warranty in the Nissan Assurance Products Resource Manual (APRM) for warranty coverage guidelines and complete information regarding warranty coverage. Please see this bulletin for further details.
NTB13106E
Service Bulletin/Repair Instructions
SERVICE INFORMATION If the configuration of the Audio/Navigation unit has not been completed correctly, some of the symptoms that may occur are: * Intermittent or no back up camera operation * No steering wheel switch response to audio inputs * No volume response from volume knob * Volume very loud or very quiet and adjustment is overly sensitive * Equalizer is adjusted so that Bass control is at maximum all the time * DTC U1000 for AVM C/U could be present If the above symptoms occur: * Confirm the configuration of the Audio/Navigation unit is correct. NOTE: Correct configuration of the appropriate control unit will restore correct operation. Audio/Navigation unit configuration is outlined starting on page 2. See this bulletin for further detail.
NTB14-084C
Service Bulletin/Repair Instructions
2-Sensor occupant classification System Diagnostics and Information
NTB13-099E
Service Bulletin/Repair Instructions
Audio Ulnit Replacement - Vehicles with color display audio and navigation system
NTB13099E
Service Bulletin/Repair Instructions
SERVICE INFORMATION If the Audio Unit needs to be replaced in an Applied Vehicle for any reason: - Write down replacement Audio Unit's registration "code" . - Replace the Audio Unit as instructed in the Electronic Service Manual (ESM) and any applicable bulletins. - Register the replacement Audio Unit with Nissan Owner Services. NOTE: The Apps mode will not function if the Audio Unit serial number (registration code) is not registered. See this bulletin for further detail.
NTB14-058B
Service Bulletin/Repair Instructions
2014-2016 Rogue; shift selector knob removal and Installation includfing the block-pull and spring
NTB14-100B
Service Bulletin/Repair Instructions
2014 Rogue; Configuring the Air Bag Diagnostic sensor Unit
NTB14058B
Service Bulletin/Repair Instructions
SERVICE INFORMATION This bulletin contains the procedure to remove and/or install the shift selector knob. It also contains information for re-installing the block-pull and spring, if needed. See this bulletin for further detail.
NTB09099A
Service Bulletin/Repair Instructions
IF YOU CONFIRM A refrigerant leak at a refrigerant pipe/hose joint location. ACTIONS 1. Inspect the metal surfaces of the pipe/hose joint for damage or contamination. NOTE: Do not replace a refrigerant pipe, hose, or other A/C component if an o-ring seal will solve the leak incident, if it should occur. 2. If no damage is found to the joint metal surfaces, replace the O-ring seal. See this bulletin for further detail.
NTB15-026A
Service Bulletin/Repair Instructions
2014-2015 Rogue; Lacks Power due to snow ingestion
NTB09131B
Service Bulletin/Repair Instructions
SERVICE INFORMATION Because of collision damage or other vehicle repair, a replacement "Certification Label" or "VIN Plate / Label" may be needed. These items may be available from Nissan by request if certain criteria are met. This bulletin lists the criteria and provides an application form for such replacements. See this bulletin for further detail.
NTB15-013B
Service Bulletin/Repair Instructions
Nissan; Procedure to clean CVT Transmission fluid coolers
NTB15-086C
Service Bulletin/Repair Instructions
2013-2016 Altima and 2014-2016 Rogue; MIL on with DTC P0776
NTB15-084B
Service Bulletin/Repair Instructions
2013-2016 Altima and 2014-2016 Rogue; CVT Judder and DTC P17F0 or P17F1 stored (4 cyl engine only)
NTB15-086B
Service Bulletin/Repair Instructions
2013-2015 Altima and 2014-2016 Rogue; MIL on with DTC P0776
NTB12-103C
Service Bulletin/Repair Instructions
CVT/TDCM Calibration Data "Write" Procedure
NTB15-044B
Service Bulletin/Repair Instructions
Fuel Filler Cap tether clip service information
NTB15044B
Service Bulletin/Repair Instructions
SERVICE INFORMATION If the clip for the fuel filler cap tether becomes lost or is detached for any reason, it is no longer necessary to replace the fuel filler cap. The clip or "pin" is now available as a separate service part. NOTE - Do not replace the fuel filler cap if only the pin is needed. See this bulletin for further detail.
NTB16-033
Service Bulletin/Repair Instructions
2014-2016 Rogue; HVAC Controller service information
NTB16033
Service Bulletin/Repair Instructions
SERVICE INFORMATION If the HVAC system control unit is replaced for any reason: - After replacement, make sure to perform Door Motor Starting Position Reset using CONSULT-III plus. - This function is found in HVAC > Work support. See this bulletin for further detail.
NTB15-045B
Service Bulletin/Repair Instructions
2014-2016 Rogue; Manual HVAC Improper operation - Equipped with Manual HVAC system (Does not apply to the Rogue Select (S35)
NTB15084B
Service Bulletin/Repair Instructions
IF YOU CONFIRM: The customer reports a transmission judder (shake, shudder, single or multiple bumps or vibration), AND One of the following DTCs are stored in the TCM: - P17F0 (CVT_JUDDER (T/M INSPECTION)) - P17F1 (CVT_JUDDER (C/U INSPECTION)) NOTE: - If a transmission judder (as described above) is NOT reported by the customer, this bulletin does not apply. - If DTC P17F0 or P17F1 was NOT found stored, this bulletin does not apply. - NTB15-083, Enhanced Diagnostic Logic For CVT Judder, has reprogramming instructions that may apply. ACTIONS: Perform the SERVICE PROCEDURE, starting on page 3. - Review the Repair Flow Chart on page 2. NOTE: Essential Tool Tech Cam (borescope) J-51951 has been sent to dealers. This tool?s attachments make CVT inspection possible. See this bulletin for further detail.
NTB16-025
Service Bulletin/Repair Instructions
Air Bag Diagnosis sensor unit coinfiguration
NTB16025
Service Bulletin/Repair Instructions
SERVICE INFORMATION If an Air Bag Diagnosis Sensor Unit is replaced and the configuration of the old unit could not be saved, use the Service Procedure in this bulletin to: - Load the VIN specific configuration file from your electronic parts catalog (FAST or equivalent) onto a portable USB storage device (thumb drive) - Plug the thumb drive into your CONSULT PC. - Configure the new Air Bag Diagnosis Sensor Unit using the file that you loaded onto the thumb drive. See this bulletin for further detail.
NTB14015C
Service Bulletin/Repair Instructions
SERVICE INFORMATION When a BCM is replaced for any reason, TPMS (Tire Pressure Monitor System) configuration must be performed. TPMS configuration is in addition to any other BCM configurations that may be performed. If TPMS configuration is not performed, TPMS transmitter ID registration will not complete. Follow the Service Procedure in this bulletin to perform TPMS configuration. See this bulletin for further detail.
NTB16020
Service Bulletin/Repair Instructions
IF YOU CONFIRM The vehicle is operated as follows: 1. The ambient temperature is below freezing (below 32°F / 0°C). 2. The engine was started and the vehicle driven a short distance. 3. The vehicle was then parked (engine turned OFF), and then allowed to sit for at least 10 minutes. THEN, when restarting the engine: - The engine will crank but not start OR - The engine will start, but the engine will not respond to throttle pedal input. AND - One or more of the following Electronic Throttle Control (ETC) related DTCs are found stored in the ECM: -P2100 (ETC MOT PWR-B1) -P2101 (ETC FNCTN/CIRC-B1) -P1726 (ELEC TH CONTROL) ACTION Replace the Intelligent Power Distribution Module (IPDM) with the one listed in the PARTS INFORMATION section of this bulletin. - Refer to the Electronic Service Manual (ESM), section PCS-Power Control System, for IPDM removal and installation. See this bulletin for further detail.
NTB03074J
Service Bulletin/Repair Instructions
SERVICE INFORMATION Occasionally customers may notice water vapor or fog in the headlamps. The information, illustrations, and flow chart in this bulletin are provided to help you in determining if an incident for water/condensation in the headlamps is normal or not. Nissan?s new vehicle limited warranty does not cover physically damaged (cracked or broken) headlamps. All current headlamp assemblies are vented to the atmosphere (not sealed). - This is necessary to allow for expansion and contraction of air from temperature "variations" (warmer or colder) without damage to the headlamp. - Moisture in the air sometimes "travels" into and out of the headlamp assembly through these vents. - Certain environmental conditions may cause moisture to condense. - The fogging/cloudiness should disappear over time when the headlamp is in a dry environment. See this bulletin for further detail.
NTB15011A
Service Bulletin/Repair Instructions
IF YOU CONFIRM On an Applied Vehicle, one or more of the following is occurring: * A status message "Update Failed !" is displayed with a direction to "Insert update media" while a countdown from 60 is displayed. The audio system then reboots (Nissan Logo appears), and then will restart the countdown. * The center display screen (navigation screen) intermittently goes blank (nothing is displayed) for a few seconds or longer and then returns to normal display. * Continuously reboots (Nissan Logo appears after a loss of soundor freeze condition). * XM channel selection is sometimes not working as normal or shows "XM loading" for long periods of time. * Audio sometimes is not working. * Soundlevels for balance, fader, treble,or bass do not correspond to what is displayed by the audio unit after the ignition is cycled. * Connected iPod freezes after using "Source" button or changing tracks. * Audio preset buttons do not respond when selected. * Calls unintentionally change from "hands free" to "handset". And * The Software version has been confirmed as "not current" (refer to page 3). See this bulletin for further details.
NTB09081C
Service Bulletin/Repair Instructions
SERVICE INFORMATION The purpose of this bulletin is to give Nissan dealers guidelines to help determine if windshield breakage is covered under warranty or is the customer?s responsibility. Nissan North America (NNA) is not responsible for damage to glass that is a result of objects striking or scratching the glass. However, NNA is responsible for manufacturing issues such as distorted glass and cracks that are due to improper installation or damage to the glass during vehicle assembly. NNA typically does not find any type of cracks in the windshield due to stress after the dealership PDI. See this bulletin for further detail.
EL15-029
Service Bulletin/Repair Instructions
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
NTB15-113
Service Bulletin/Repair Instructions
2013 Rogue and 2014 Rogue Select; Low Power/stop Lamps stay on.
NTB16003
Service Bulletin/Repair Instructions
SERVICE INFORMATION The Intelligent Keys used on the various Nissan vehicles may not be interchangeable between models and years. See this bulletin for further detail.
NTB09022G
Service Bulletin/Repair Instructions
SERVICE INFORMATION Design and process changes have been made to improve battery voltage at dealer receipt. Our goal is to deliver vehicles to customers with a 12 volt battery in excellent condition. Proper dealership storage and maintenance of vehicle 12 volt batteries is essential to insuring good battery operating life and customer satisfaction. Dealers are responsible for maintaining vehicles in their inventory. 12 volt batteries in vehicle inventory should always be kept at a full charge to prevent excessive discharge during storage and so they are ready for delivery to customers at any time. See this bulletin for further detail.
NTB10029C
Service Bulletin/Repair Instructions
IF YOU CONFIRM There is a vibration or judder feeling from the rear of the vehicle; when making, turns, on dry roads, or at low speeds (under 40 MPH), and the vibration does not occur if the Electric Controlled Coupling is electrically disconnected. ACTION Replace the Electric Controlled Coupling for the rear final drive. See this bulletin for further detail.
NTB13028A
Service Bulletin/Repair Instructions
SERVICE INFORMATION Windshield "foreign material" that is on the surface of the glass in some cases can be cleaned off with a very particular type and grade of steel wool. * Most any foreign material on the surface of the Windshield can be cleaned off by using #0000 super fine steel wool. >The #0000 grade super fine steel wool can be found in most hardware stores. Please see this bulletin for further details.
NTB14068A
Service Bulletin/Repair Instructions
SERVICE INFORMATION Power moonroof initialization procedures for the Applied Vehicles have been revised. The procedure described in this bulletin differs from the procedure in the Electronic Service Manual (ESM). At a later date and where possible, the applicable ESMs will be updated with the revised procedures. Follow the procedure in this bulletin should the power moonroof in an Applied Vehicle need to be initialized. See this bulletin for further details.
AT15-015A
Service Bulletin/Repair Instructions
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
NTB14114A
Service Bulletin/Repair Instructions
IF YOU CONFIRM All "hands free" functions of the Intelligent Key (I-Key) do not work. For example, the doors will not lock or unlock when pressing either front door request switch. NOTE: - The issue of all I-Key "hands free" functions not working may occur intermittently or all the time. - The message "No Key Detected" or similar may show on the Vehicle Information Display (located in the combination meter). - All I-Key remote button functions (door lock/unlock, etc.) WILL work normally when all I-Key "hands free" functions are NOT working. ACTION 1. Inspect the I-Key?s battery on its negative contact side. 2. If excessive scratching is found, replace the battery. 3. Verify all I-Key functions (both "hands free" and remote) work properly after battery replacement. NOTE: Do NOT replace the BCM, I-Key, or other parts for the issue described under IF YOU CONFIRM, if it should occur. See this bulletin for further detail.
NTB12099D
Service Bulletin/Repair Instructions
SERVICE INFORMATION: The Navigation (NAVI) SD Map Data Cards are not interchangeable between the two versions of NAVI units offered in Nissan vehicles that use this type of map data. * If the wrong SD Map Data Card is used, the NAVI will display an update screen (Figures 1 and 2, reference only) and will only accept Cancel. * If this screen is displayed, install the correct SD Map Data Card, found in table A on page 2, and the NAVI unit will return to correct operation. See this bulletin for further detail.
NTB15062A
Service Bulletin/Repair Instructions
IF YOU CONFIRM There is a popping noise from either the right or the left front coil springs when turning to the right or left. NOTE: Electronic chassis ears may be helpful in isolating this type of noise. ACTION Replace both front coil springs, strut mount bearings, and all other parts listed under PARTS INFORMATION. Position the coil springs as shown on pages 2-5. Check the front end alignment, adjust to factory specifications as needed. NOTE: Refer to the Electronic Service Manual (ESM), section FSU Front Suspension, for strut coil spring removal, installation, and alignment information. IMPORTANT: The Coil Spring Installation Guidelines section in this bulletin MUST be followed in order for a correct repair to be performed.
NTB11069C
Service Bulletin/Repair Instructions
IF YOU CONFIRM The customer states HomeLink will not operate or has improper operation. ACTIONS 1. To significantly reduce unnecessary repairs, make sure: a. The vehicle is not in "Transit Mode" (if equipped). - Not in Transit Mode: With the turn signal switch is in the OFF (center) position, turn the ignition from OFF to ON. If the turn signal indicators stay OFF (do not illuminate), the vehicle is not in Transit Mode. b. The "Extended Storage Switch" (if equipped) is in the "Customer Delivery" position (pushed in). - The Extended Storage Switch is located on the fuse block that is located in the interior of the vehicle. 2. Confirm the customer is familiar with the HomeLink programming procedure located in the vehicle?s owner?s manual. 3. Test HomeLink operation with special tool HomeLink Transmitter Tester J-41540. See this bulletin for further detail.
NTB15083
Service Bulletin/Repair Instructions
IF YOU CONFIRM: The customer reports a transmission judder (shake, shudder, single or multiple bumps or vibration). NOTE: A new diagnostic logic has been established to enhance the diagnostic process by storing diagnostic trouble codes (DTCs) on applied vehicles. These new DTC?s are: P17F1 (CVT_JUDDER (C/U INSPECTION)) P17F0 (CVT_JUDDER (T/M INSPECTION)) ACTION: 1. Refer to step 6 and TABLE A on page 4 in the SERVICE PROCEDURE to confirm this bulletin applies to the vehicle you areworking on. 2. If this bulletin applies, reprogram the TCM (Transmission Control Module). Please see this bulletin for further details.
NTB14029B
Service Bulletin/Repair Instructions
IF YOU CONFIRM All of the following - The engine will not start (no crank; starter will not engage) when pushing the ignition switch, and I-Key Error message is displayed in the combination meter, and DTC B2604 (PNP/Clutch Switch) is stored, past or present. ACTION Perform adjustment of the shift control cable per the Service Procedure in this bulletin. See this bulletin for further detail.
NTB13088A
Service Bulletin/Repair Instructions
SERVICE INFORMATION This bulletin has compiled Tire Pressure Monitor System (TPMS) and Low Tire Pressure Warning System (LTPWS) information for: - Basic diagnosing of TPMS/LTPWS systems - Radio frequency interference causing a "No Data" (C1708, C1709, C1710, C1711) condition - Sensor leaks - Moving TPMS/LTPWS wheel assemblies from one vehicle to another and TPMS/LTPWS sensor registration - Air pressure changes with altitude and ambient temperatures - Aftermarket tire sealers - Aftermarket wheels - Inflating/deflating tires with TPMS/LTPWS sensors See this bulletin for further detail.
NTB14057A
Service Bulletin/Repair Instructions
SERVICE INFORMATION The information in this bulletin is provided to help ensure correct diagnosis and repair of fluid leaks. All fluid leaks, when properly diagnosed, should be repaired (whether under warranty or customer pay) to ensure proper vehicle operation. However, certain normal operating conditions can be misdiagnosed as a leak requiring repair. Unnecessary repair or replacement of parts in connection with incorrectly diagnosed "leaks" can negatively impact customer satisfaction, be time consuming and costly, and if not performed correctly can lead to future repairs. See this bulletin for further detail.
NTB15070
Service Bulletin/Repair Instructions
IF YOU CONFIRM An oil leak from the Adapter Case Oil Seal or the O-ring (see Figure 1). ACTION NOTE: DO NOT replace the Transfer Case for a leak from the Adapter Case Oil Seal or the O-ring. Reseal the Adapter Case with the seals listed in PARTS INFORMATION and shown in Figure 1. * Please see this bulletin for further details.
NTB-14-069-B
Service Bulletin/Repair Instructions
NISSAN: SOME VEHICLES ARE EXPERIENCING THE FRONT BAT SUNSHADE KEEPER HANGING DOWN OR THE FABRIC FOR SUNSHADE IS CAUGHT IN TRACKS AND WOULD NEED TO BE REPLACED. MODEL 2014-15 ROGUE. *PE
NTB14069B
Service Bulletin/Repair Instructions
IF YOU CONFIRM: The sunshade fabric catches in its tracks and/or the sunshade keeper (front bar) is hanging down. ACTION: Replace the sunshade assembly. - Install a plastic retainer clip on the one end of the sunshade. - Refer to this bulletin?s SERVICE PROCEDURE for sunshade removal and installation. See this bulletin for further detail.
NTB-14-115-A
Service Bulletin/Repair Instructions
NISSAN: 2013-2015 ALTIMA, MURANO, ROGUE(T32). CONFIGURATION MUST BE PERFORMED ON THE SELECTED VEHICLES WHEN AN ABS CONTROL UNIT IS BEING REPLACED. *LJ UPDATED 9/10/15. *PE
NTB14115C
Service Bulletin/Repair Instructions
SERVICE INFORMATION For the Applied Vehicles in this bulletin, when an ABS Actuator and Electric Unit (ABS control unit) is replaced for any reason, Configuration of the ABS Control Unit must be performed. If Configuration is not performed, DTC C1170 (VARIANT CODING) will be stored. The Service Procedure in this bulletin contains the steps for performing ABS Control Unit Manual Configuration. See this bulletin for further detail.
NTB-15-062
Service Bulletin/Repair Instructions
NISSAN: SOME VEHICLES ARE EXPERIENCING A POPPING NOISE WHEN TURNING EITHER RIGHT OR LEFT COMING FROM FRONT COIL SPRINGS AND BOTH FRONT COIL SPRINGS AND STRUT BEARINGS NEED REPLACING. MODEL 2014-15 ROGUE. *PE
NTB12055E
Service Bulletin/Repair Instructions
IF YOU CONFIRM: Customers concern of a "clicking" noise coming from either left or right front/rear CV-type axles during take-off/acceleration. ACTION: Apply Molykote M77 grease (P/N 44003-7S000) to the hub bearing surfaces. NOTE: * Do not remove the axle from the hub or transmission for this bulletin * Refer to the Electronic Service Manual (ESM) for model specific torque specifications. - For 2007-2013 Versa and 2013 LEAF vehicles, see the Service Procedure torque specifications on page 4. See this bulletin for further detail.
NTB15060
Service Bulletin/Repair Instructions
SERVICE INFORMATION When servicing run flat tires or low profile tires: - Special equipment and procedures are required to avoid damage. - Specifically, Tire Pressure Monitor transmitters (TPMS sensors) can be damaged when improperly dismounting and mounting tires. - TPMS sensors becoming damaged during mounting or dismounting tires are not covered under warranty. - To avoid such damage, ensure that the tire changer being used and the operator of the tire changer is capable of servicing run flat and low profile tires. - Operator?s manuals for such tire changers must be followed. See this bulletin for further detail.
NTB15055
Service Bulletin/Repair Instructions
SERVICE INFORMATION After ECM reprogramming, the Calibration Verification Number (CVN) needs to be automatically calculated prior to State emissions testing (also known as Inspection Maintainence, I/M, or SMOG testing depending upon location). Allowing the vehicle to idle for 22 minutes will allow for faster CVN calculation. It is recommended that customers utilize this method if the vehicle needs to be tested for emissions soon after ECM reprogramming. See this bulletin for further detail.
NTB15048
Service Bulletin/Repair Instructions
IF YOU CONFIRM Vibration, booming or drone is present while stopped, at idle and transmission is in Drive: * From the steering wheel with the A/C ON. Or * From the front passenger seat with the A/C OFF. And * The level of vibration is greater than a known good vehicle. ACTION Refer to the Flow Chart on page 2 to confirm if this bulletin applies. Please see this bulletin for further details.
NTB15043
Service Bulletin/Repair Instructions
SERVICE INFORMATION The appearance of painted alloy wheels can be damaged if acidic cleaners are used. DO NOT use Chrome Wheel Cleaner on Painted Wheels. Many chrome wheel cleaners have acidic ingredients. Make sure to follow all instruction in the Appearance and Care Section of the Owner?s Manual. Damage to wheel appearance due to the use of inappropriate chemicals or cleaning products is not covered under warranty. See this bulletin for further detail.
NTB15-038
Service Bulletin/Repair Instructions
NISSAN 2015 ROGUE , ALTIMA, NV200: VOLUNTARY SERVICE CAMPAIGN CONCERNING REPLACEMENT OF TORQUE CONVERTER ON CERTAIN VEHICLES. *LJ
NTB15035
Service Bulletin/Repair Instructions
SERVICE INFORMATION If you confirm there is a need to replace the combination meter front cover (lens) on an Applied Vehicle for any reason (scratch, blemish, etc.): - Do not replace the entire combination meter assemby. The front cover of the combination meter assembly is available as a separate service part. - Refer to the Electronic Service Manual, section MWI-Meter, Warning Lamp & Indicator, for replacement information. See this bulletin for further detail.
NTB14-015B
Service Bulletin/Repair Instructions
NISSAN 2014-2015 ROGUE(T32): INFORMATION INVOLVING TPMS CONFIGURATION, WHEN A BCM IS REPLACED, TIRE PRESSURE MONITOR SYSTEM CONFIGURATION MUST BE PERFORMED. *LJ
NTB15027
Service Bulletin/Repair Instructions
SERVICE INFORMATION This bulletin is provided as supplemental information to aid in assisting the customer and servicing a vehicle with customer-reported FCW (Forward Collision Warning) system questions or issues. See this bulletin for further detail.
NTB10112E
Service Bulletin/Repair Instructions
SERVICE INFORMATION For vehicles delivered to the dealers with wheel protector covers - Do not remove the wheel protector covers during Pre-Delivery Inspection (PDI) - Wheel protector covers help prevent cosmetic rotor corrosion. See this bulletin for further detail.
NTB99060G
Service Bulletin/Repair Instructions
SERVICE INFORMATION NOTE - Failure to follow the procedures in this bulletin may result in the denial of a warranty claim. In an effort to protect the paint finish, Paint Guard Film (PGF) is applied on many new Nissan vehicles. Paint Guard Film is a temporary white plastic protective film that is applied by the factory to the horizontal painted surfaces of the vehicle. The PGF protects the paint finish during vehicle handling, transportation and storage from harmful elements such as acid rain, iron particles, bird droppings, tree sap and other environmental contaminants. NOTE - Paint Guard Film CANNOT remain on the vehicle for more than six months after the vehicle's manufacture date. PGF must be removed at the end of six months. See this bulletin for further detail.
NTB00042D
Service Bulletin/Repair Instructions
SERVICE INFORMATION Changes or modifications to the front seat assembly trim materials may affect the proper operation of the Front Seat-Mounted Side-Impact Supplemental Air Bags and Passenger Occupant Classification Sensor and could result in serious personal injury or death. Nissan STRONGLY RECOMMENDS AGAINST making any change to seat trim materials from the factory equipped condition. This specifically applies to replacing the seat trim with non-factory materials; adding leather/cloth seat covers, seat pads, or seat storage pouches, etc. around or over the seat back and the passenger seat cushion. See this bulletin for further detail.
NTB13015A
Service Bulletin/Repair Instructions
SERVICE INFORMATION DTC B2190 (NATS ANTENNA AMP) can be stored for the following reasons: 1. Something other than an Intelligent Key is inserted into the Key-Slot. 2. An Intelligent Key issue. 3. A wiring issue between the Key-Slot and the BCM. 4. A Key-Slot issue. If DTC B2190 is stored due to 1 or 2 above, it will not erase, or go to "PAST", until a known good registered Intelligent Key is inserted into the Key-Slot. For DTC B2190 diagnosis; first perform the Service Manual DTC Confirmation Procedure. See this bulletin for further detail.
NTB13096B
Service Bulletin/Repair Instructions
SERVICE INFORMATION If the Audio Unit needs to be replaced in an Applied Vehicle for any reason: - Replace the Audio Unit as instructed in the Electronic Service Manual (ESM). - Register the replacement Audio Unit serial number with Nissan Owner Services. NOTE: The Apps mode will not function if the Audio Unit serial number is not registered. See this bulletin for further detail.
NTB14-113
Service Bulletin/Repair Instructions
NISSAN: 2014 ROGUE FRONT AIR CONTROL UNIT NEEDS PART REPLACEMENT, PART NUMBER 2750-4BB0B. *LJ
NTB14113
Service Bulletin/Repair Instructions
IF YOU CONFIRM DTCs B24B7 (Intake Door), B24B9 (Mode Door), and B24BB (Air Mix Door) are stored. ACTION 1. Replace the Front Air Control Unit with the new part listed in the PARTS INFORMATION section. - Refer to the Electronic Service Manual (ESM), section HAC-Heater and Air Conditioning System, for removal and installation information. 2. Erase DTCs, and confirm B24B7, B24B9, and B24BB do not store. - If DTC B24B7, B24B9, and B24BB store after replacement of the Front Air Control Unit, refer to ASIST and the ESM for further diagnosis. See this bulletin for further detail.
NTB14109
Service Bulletin/Repair Instructions
SERVICE INFORMATION Starting with 2010 Model Year, Nissan vehicles have been gradually incorporating a new type of DTC known as Permanent DTC or P-DTC. If a vehicle is equipped with P-DTCs, all emission related DTCs will also set a P-DTC if the MIL is turned ON. A listing of which DTCs that will also set a P-DTC is found in the DTC Index in the EC-Engine Control section of the Electronic Service Manual (ESM). If a DTC repair is performed and the DTC erased, a vehicle may fail an Emission Inspection and Maintenance test if the P-DTC is not also erased. See this bulletin for further detail.
PC330
Service Bulletin/Repair Instructions
Nissan is conducting a dealer inventory inspection to inspect the front axle hub and torque member bolts on 160 specific 2014-15 Nissan Pathfinder and Rogue vehicles identified in SERVICE COMM.
NTB14107
Service Bulletin/Repair Instructions
SERVICE INFORMATION If a customer describes lack of power or poor acceleration, perform the following checks before attempting any repair: * Check for stored DTCs. * Check if the driver is resting their left foot on the brake pedal while accelerating. Advise the customer not to rest their foot on the brake while accelerating. * Use CONSULT-III plus in Engine Data Monitor to check operation of the brake lamp circuit signal. Monitor the brake switch during the incident; it should be "OFF". Please see this bulletn for further details.
MAILV
Service Bulletin/Repair Instructions
Nissan is conducting a Voluntery Service Campaign on certain MY2014 Rogue vehicles to provide an Owner's manual supplement booklet to customers which revises or adds information.
NTB14105
Service Bulletin/Repair Instructions
IF YOU CONFIRM: The carpet is wet on the driver and/or front passenger floor (see Figure 1). - A "sloshing" type noise may be heard while driving AND the source of the wetness is not caused by the air conditioning system. ACTION: 1. Determine if the leak is from the kick panel and/or cowl end area. 2. If confirmed, apply body sealant to the incident areas as outlined in this bulletin. See this bulletin for further detail.
PC327
Service Bulletin/Repair Instructions
Nissan is conducting an inventory inspection on 105,290 specific MY2013-15 Nissan ALT, PTH, LEF, MUR, NV2, NVT, SEN, and VER NOTE vehicles to inspect the software on the OCS ECU.
NTB14-100A
Service Bulletin/Repair Instructions
NISSAN ROGUE: THE AIRBAG SENSOR MUST BE CONFIGURED ONCE REPLACED . *LJ
MAILUOL
Service Bulletin/Repair Instructions
Nissan is conducting a Voluntary Service Campaign on MY2014 Rogue & Altima vehicles to draw the customer?s attention important information regarding the maintenance and cleaning of the touch screen in outlined in the Owner's Manual.
MAILVOL
Service Bulletin/Repair Instructions
Nissan is conducting a Voluntery Service Campaign on certain MY2014 Rogue vehicles to provide an Owner's manual supplement booklet to customers which revises or adds information.
MAILU
Service Bulletin/Repair Instructions
Nissan is conducting a Voluntary Service Campaign on MY2014 Rogue & Altima vehicles to draw the customer?s attention important information regarding the maintenance and cleaning of the touch screen in outlined in the Owner's Manual.
NTB-14-100
Service Bulletin/Repair Instructions
NISSAN: WHEN EVER AIR BAG DIAGNOSIS SENSOR UNIT IS REPLACED, IT MUST BE CONFIGURED AND IF NOT, DTC B1427-55 WILL BE SET, ON CERTAIN VEHICLES. MODEL 2014 ROGUE. *PE
NTB13085B
Service Bulletin/Repair Instructions
IF YOU CONFIRM Satellite radio (SXM) will only show the channel number and name, but will not show artist and track/title information, and/or the radio buttons will not illuminate at times, while the display and the HVAC/Cabin lighting is operating correctly, and/or the Bluetooth will take up to 2 minutes to connect when using the vehicle's onboard Pandora® or iHeartRadio Internet Apps with an iPhone® and "No Device Found" is displayed for longer than normal, and/or when not in reverse, the center display screen becomes a pink/purple color with the reverse guide lines displayed. ACTION Update the Audio Visual System software. Refer to the Service Procedure on page 3. See this bulletin for further details.
NTB14098
Service Bulletin/Repair Instructions
IF YOU CONFIRM All of the following: The battery was disconnected, or the battery was discharged, and then after reconnecting or recharging the battery fuel was added to the fuel tank, and then after adding fuel the Range or DTE (Distance To Empty) reading on the Vehicle Information Display did not reset. ACTION Reprogram the Vehicle Information Display (METER/M&A) per the Service Procedure in this bulletin. See this bulletin for further detail.
NTB14095
Service Bulletin/Repair Instructions
IF YOU CONFIRM The images and information on the Vehicle Information Display are shifted from their normal positions, vertically or horizontally, or the customer reports this incident. ACTION Reprogram the Vehicle Information Display (METER/M&A) per the Service Procedure in this bulletin. See this bulletin for further detail.
PC311OL
Service Bulletin/Repair Instructions
Nissan is conducting a Voluntary Service Campaign on certain MY2014 rogue vehicles to replace the engine on/off push button.
NTB-14-084
Service Bulletin/Repair Instructions
NISSAN: REGARDING SOME VEHICLES USING TWO STAIN GAUGE OCCUPANT CLASSIFICATION SYSTEM (OCS) OPERATION, AND THE PRESSURES NECESSARY DUE TO DIFFERENT RESPONSE OF OCCUPANT SEATING POSTURE. MODEL 2013-2015 ALTIMA, SENTRA, PATHFINDER, LEAF, NV200, NV200 TAXI, ROGUE. *PE
NTB-14-082
Service Bulletin/Repair Instructions
NISSAN: SEE DOCUMENT SEARCH BUTTON FOR OWNER LETTER. INFORMATION PROVIDED REGARDING THE REPLACEMENT OF ENGINE ON/OFF PUSH BUTTON, AT NO CHARGE, ON SOME VEHICLES. MODEL 2014 ROGUE. *PE
NTB14082
Service Bulletin/Repair Instructions
INTRODUCTION Nissan is conducting a Voluntary Service Campaign on certain Model Year 2014 Rogue vehicles. On affected vehicles, the engine on/off push button will be replaced at no charge for parts or labor. IDENTIFICATION NUMBER Nissan has assigned identification number PC311 to this campaign. This number must appear on all communications and documentation of any nature dealing with this campaign. See this bulletin for further detail.
PC311A
Service Bulletin/Repair Instructions
***** Repair Instructions ***** Nissan has released a campaign technical service bulletin for Campaign PC311 ? 2014 Rogue Engine On/Off Push Button. The bulletin (NTB14-082) will be available on ASIST and NNAnet.com. The technical procedure released previously will be removed since it has been superseded by this bulletin.
PC315
Service Bulletin/Repair Instructions
Nissan is conducting a dealer service action of the rear lift gate hinge mounting bolt torque on 1,372 specific 2014 Rogue vehicles identified in SERVICE COMM.
PC311
Service Bulletin/Repair Instructions
Nissan is conducting a Voluntary Service Campaign on certain MY2014 rogue vehicles to replace the engine on/off push button.
NTB13077A
Service Bulletin/Repair Instructions
SERVICE INFORMATION Applied vehicles equipped with a CVT have a "cap" that appears to be a fluid level gauge. This "cap" will NOT have a gauge or "dipstick". This is normal. Do NOT replace the "cap" because it is thought to have a "dipstick". The fluid level is not checked from this location. The fluid level for applied vehicles is checked from the oil pan (refer to the appropriate section of the Electronic Service Manual [ESM]). Whenever checking, filling, or topping off a CVT's fluid level of an applied vehicle for any reason, use the procedure outlined in the appropriate section of the ESM. See this bulletin for further detail.
NTB14077
Service Bulletin/Repair Instructions
SERVICE INFORMATION The purpose of this bulletin is to clarify language contained in the owner?s manual language for the APPLIED VEHICLES. For the APPLIED VEHICLES, the below language supersedes similar language in existing owner?s manuals. Future printings of owner?s manuals for the APPLIED VEHICLES will also contain the below language. For the APPLIED VEHICLES: NISSAN recommends using Genuine NISSAN NS-3 CVT Fluid ONLY in NISSAN CVTs. Do not mix with other fluids. Do not use Automatic transmission fluid (ATF) or Manual Transmission fluid in a NISSAN CVT, as it may damage the CVT. Damage caused by the use of fluids other than as recommended is not covered under NISSAN's New Vehicle Limited Warranty. Using fluids that are not equivalent to Genuine NISSAN NS-3 CVT Fluid may also damage the CVT. Damage caused by the use of fluids other than as recommended is not covered under NISSAN's New Vehicle Limited Warranty. See this bulletin for further detail.
NTB-14-072
Service Bulletin/Repair Instructions
NISSAN: USE CORRECTED SPECIFICATION (SD) FOR POSITIONING TARGETS WHEN PERFORMING THE CALIBRATION FOR REAR VIEW CAMERA, THAT MONITORS TRAVELING LANE. MODEL 2014 ROGUE.
NTB14072
Service Bulletin/Repair Instructions
SERVICE INFORMATION When performing Rear View Camera calibration, use the corrected specification (Sd) for positioning the targets. NOTE: * The Rear View Camera monitors the traveling lane. It transmits the camera image signal to around view monitor control unit for the Lane Departure Warning (LDW) system. * The specification in the Electronic Service Manual (ESM), Section DAS - Driver Assistance Systems, for positioning the Rear View Camera Targets are incorrect. Use the corrected specification (Sd) listed below. Please see this bulletin for further details.
NTB14067
Service Bulletin/Repair Instructions
IF YOU CONFIRM The maintenance interval mileage in the Vehicle Information Display resets to zero with each ON > OFF > ON ignition cycle, ACTION Reprogram the Vehicle Information Display (METER/M&A) per the Service Procedure in this bulletin. See this bulletin for further detail.
NTB14039A
Service Bulletin/Repair Instructions
SERVICE INFORMATION If one or both Intelligent Keys cannot be located prior to customer delivery of an Applied Vehicle, refer to the applicable section of this bulletin for Intelligent Key registration instructions. - One (1) Intelligent Key Is Lost ---- Page 2 - Two (2) Intelligent Keys Are Lost ---- Page 3 NOTE - If both Intelligent Keys are lost with the BCM in Transit Mode, the BCM and ECM will need to be replaced. Refer to pages 3 - 5 for more information. See this bulletin for more detail.
PC304
Service Bulletin/Repair Instructions
Nissan is conducting a dealer inventory inspection of the automatic climate control system operation on 910 specific 2014 Rogue vehicles identified in SERVICE COMM.
NTB10066A
Service Bulletin/Repair Instructions
SERVICE INFORMATION Related to communication codes U1000, U1001, U1002, U1010: - Always diagnose the communication codes first. - When a module reports a U1000 code, it is typically operating normally; however, there is a communication error external to that module on the CAN network. - U1000 indicates an error. V-CAN diagram or CAN Diag Support Monitor provides data to determine the location of the error. See this bulletin for more information.
PC300A
Service Bulletin/Repair Instructions
The original VIN list provided with the initial announcement contained 29 vehicles that are not equipped with push-button ignition. These 29 vehicles are exempt from the repair and are no longer subject to the quality hold.
NTB14055
Service Bulletin/Repair Instructions
SERVICE INFORMATION For 2014 - 2015 Rogue (T32) equipped with third row seats: Do not install or add a spare tire to the vehicle. The vehicle is not designed to be equipped with a spare tire. See this bulletin for further detail.
PC300
Service Bulletin/Repair Instructions
Nissan is conducting a dealer inventory service action to replace the push button ignition switch on 158 specific 2014 Rogue vehicles identified in SERVICE COMM.
NTB-14-050
Service Bulletin/Repair Instructions
NISSAN: THE POSITIONING OF DISTANCE SENSOR TARGET BOARD IS INCORRECT, IN ELECTRONIC SERVICE MANUAL (ESM), AND THE CORRECTED SPECIFICATION (L), IS USED TO PERFORM THE DISTANCE SENSOR ALIGNMENT. MODEL 2014 ROGUE. *PE
NTB14050
Service Bulletin/Repair Instructions
SERVICE INFORMATION When performing Distance Sensor Alignment, use the corrected specification (L) for positioning the target board. NOTE: The Distance Sensor is used for the Forward Collision Warning (FCW) system. The specification in the ElectronicService Manual (ESM), Section DAS, Driver Assistance Systems, for positioning the Distance Sensor Target Board is incorrect. Use the corrected specification (L) listed in this bulletin.
NTB14048
Service Bulletin/Repair Instructions
SERVICE INFORMATION Factory wheel covers are installed on vehicles during Pre Delivery Inspection (PDI). Care must be taken to properly install the wheel covers to avoid damage. Go to SERVICE PROCEDURE in this bulletin for proper wheel cover installation. NOTE: Damage to wheel covers caused by improper installation is not covered under warranty. See this bulletin for further detail.
NTB14047
Service Bulletin/Repair Instructions
IF YOU CONFIRM: The "front door power window and door lock/unlock switch (RH) finisher" (switch finisher) has a loose fit, causting an excessive gap. See Figure 1. ACTION: 1. Remove the passenger front door finisher (door finisher). - Refer to the Electronic Service Manual (ESM), section INT-Interior, for removal procedure. 2. Install a foam block where shown in SERVICE PROCEDURE. - Use the foam block listed in PARTS INFORMATION. 3. Install the door finisher with a new switch finisher listed in PARTS INFORMATION. - Refer to the ESM, section INT-Interior, for installation procedure. See this bulletin for further detail.
NTB14038
Service Bulletin/Repair Instructions
SERVICE INFORMATION When registering the Intelligent Keys (I-Keys) to a vehicle for one of the following concerns: * After replacing the BCM. Or * When one of the I-Keys has been lost and needs to be replaced. Or * When additional I-Keys are being added to the vehicle. Always use the following steps to insure proper registration of the I-Keys: 1. First Initialize the BCM. 2. Register all of the vehicle?s ?previously registered? I-Keys to the vehicle first. And then 3. Register any new (additional) I-Keys only after all of the pre-existing I-Keys have been registered. 4. Confirm operations of all I-Keys. Please see this bulletiln for further details.
NTB14032
Service Bulletin/Repair Instructions
SERVICE INFORMATION Warranty claims coding for repairing wiring harnesses for all Nissan vehicles has changed. This bulletin gives an outline of the technician?s responsibilities in assisting the dealer?s claims administrator to properly code a harness repair. Failure to provide correct information may result in claims suspension or rejection. See this bulletin for further detail.
NTB-14-026
Service Bulletin/Repair Instructions
NISSAN: THE MAIN HARNESS TO BODY HARNESS CONNECTORS IS EXPERIENCING ELECTRICAL CORROSION ISSUES. 2008-2014 ROGUE. *PE
NTB14026
Service Bulletin/Repair Instructions
IF YOU CONFIRM: An electrical issue caused by corrosion in the Main Harness to Body Harness connectors located at the bottom of the driver side A-pillar: Connector numbers M13 to B3 and/or M14 to B4. ACTIONS: 1. Preform repairs to harness connectors as needed. 2. Apply Harness Protector to cover the harness connectors. See this bulletin for further detail.
NTB14021
Service Bulletin/Repair Instructions
IF YOU CONFIRM The Instrument Lower Panel LH (as shown in Figure 1) molded plastic clip will not stay secured. ACTION Install a shim between the Steering Member and the Instrument Panel and apply felt tape to the Instrument Lower Panel LH with the SERVICE PROCEDURE starting on page 2. Please see this bulletin for further details.
PC274
Service Bulletin/Repair Instructions
Nissan is conducting a Dealer Inventory Inspection to inspect the right front and right rear lug nuts on 372 certain specific 2014 Nissan Rogue and Pathfinder vehicles currently in dealer inventory.
PC266
Service Bulletin/Repair Instructions
Nissan is conducting a customer satisfaction action on certain MY2014 Nissan Rogue SL AWD vehicles to send customers a Cargo Protector accessory that was inadvertently listed on the Monroney label but was not installed.
NTB14019
Service Bulletin/Repair Instructions
IF YOU CONFIRM The MIL is on with any one of these DTCs alone, or any combination of any of DTCs: * P2765 - CLUTCH B SPEED SENSOR * P0500 - VEH SPEED SEN/CIRC * P1574 - ASCD VHL SPD SEN * P1715 - INPUT SPEED SENSOR * P0720 - VEH SPD SEN/CIR And * Moisture and/or corrosion is present on or around the Secondary Speed Sensor pins. ACTION a. Remove the moisture from the Harness connector with CRC QD (or equivalent) electric cleaner. b. Replace Secondary Speed Sensor shown in Figure 1. Please see this bulletin for further details.
PC266OL
Service Bulletin/Repair Instructions
Nissan is conducting a customer satisfaction action on certain MY2014 Nissan Rogue SL AWD vehicles to send customers a Cargo Protector accessory that was inadvertently listed on the Monroney label but was not installed.
NTB14018
Service Bulletin/Repair Instructions
IF YOU CONFIRM A rattle coming from the exhaust center tube heat shield, and a heat shield spot weld is detached, ACTION Install a band clamp around the heat shield and over the detached spot weld. See this bulletin for further detail.
PC268A
Service Bulletin/Repair Instructions
On a very small percentage of vehicles, the steering column bolt may need to be replaced by the dealership. Nissan is placing the vehicles that have not had the inspection performed on a Quality Hold.
PC267
Service Bulletin/Repair Instructions
Nissan is conducting a Dealer Service Action to inspect and, if necessary, replace the steering knuckle on certain specific 2014 Nissan Rogue vehicles currently in inventory.
PC268
Service Bulletin/Repair Instructions
Nissan is conducting a Dealer Service Action to inspect the steering column bolt on certain specific 2014 Nissan Leaf and Rogue vehicles currently in dealer inventory only.
NTB08055C
Service Bulletin/Repair Instructions
SERVICE INFORMATION Information necessary to service the Supplemental Restraint System (SRS) safely is included in the "RESTRAINTS" section of the Electronic Service Manual (ESM) for each vehicle. IMPORTANT: Turn the ignition switch OFF, disconnect both battery terminals, and wait at least 3 minutes before performing any service on the SRS. See this bulletin for further detail.
PC260
Service Bulletin/Repair Instructions
Nissan is conducting a Dealer Service Action to inspect the CVT output speed sensor on certain specific 2014 Nissan Altima, Pathfinder, Rogue vehicles currently in dealer inventory only.
NTB12091A
Service Bulletin/Repair Instructions
SERVICE INFORMATION Replacement Engine Control Modules (ECMs) for many newer Nissan vehicles are now "Blank" ECMs. Blank ECMs come without software and must be programmed (not reprogrammed) before they will function. See this bulletin for further detail.
NTB13107
Service Bulletin/Repair Instructions
SERVICE INFORMATION Intelligent Key (I-Key) systems on the Applied Vehicles use two (2) different Radio Frequencies (RF) that are similar to other wireless devices; 315 MHz and 433 MHz. In the event another wireless device (e.g. aftermarket alarm system) is transmitting at the same time as an I-Key, it can interfere with the I-Key signals being received by the BCM. If there is interference with I-Key signals, the following symptoms may occur: - The I-key is not detected, causing: - The engine to not start (no response when the Stop/Start button is pressed) - "I-Key System Error" displayed in the instrument cluster - "No I-Key Detected" displayed in the instrument cluster - Intermittent operation of the buttons on the remote (Key FOB). - Intermittent operation of the door request switches. If a vehicle has experienced the above symptoms, or a customer has reported the above symptoms, refer to Supplemental Diagnosis / Information in this bulletin. See this bulletin for further detail.
PC255
Service Bulletin/Repair Instructions
Nissan is conducting a Dealer Service Action to inspect for water leaks at the rear liftgate glass on certain specific 2014 Nissan Rogue vehicles currently in dealer inventory.
PC254
Service Bulletin/Repair Instructions
Nissan is conducting a Dealer Service Action to inspect, remove, clean and, reinstall the shifter knob assembly on certain specific 2014 Nissan Rogue vehicles currently in dealer inventory.
NTB-13-088
Service Bulletin/Repair Instructions
NISSAN: INFORMATION REGARDING TIRE PRESSURE MONITOR SYSTEM (TPMS) AND LOW TIRE PRESSURE WARNING SYSTEM (LTPWS) FOR SENSOR LEAKS, AIR PRESSURE CHANGES WITH ALTITUDE AND AMBIENT TEMPERATURES, AFTERMARKET WHEELS, RADIO FREQUENCY INTERFERENCE CAUSING NO DATA CONDITION AND INFLATING/DEFLATING TIRES WITH TPMS/LTPWS SENSORS. MODEL ALL. NO MODELS YEARS. *PE