Vehicle report

2017 NISSAN ROGUE

Compare every NISSAN ROGUE yearNHTSA and EPA records

Service bulletins

256 bulletins

Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.

NTB09-131C

Service Bulletin/Repair Instructions

CERTIFICATION LABEL AND VIN PLATE REPLACEMENT SERVICE INFORMATION Because of collision damage or other vehicle repair, a replacement “Certification Label” or “VIN Plate/Label” may be needed. HINT: Certification Label = FMVSS (Federal Motor Vehicle Safety Standards) label. These items may be available from Nissan by request if certain criteria are met. This bulletin lists the criteria and provides an application form for such replacements. · The “VIN Plate/Label” (metal plate or vinyl label) is attached to the instrument panel or body on the driver side at the base of the windshield (see Figure 1). · The “Certification Label” (vinyl adhesive label) is located on the lower area of the driver side B-Pillar (see Figure 1).

NTB19-033G

Service Bulletin/Repair Instructions

INTELLIGENT CRUISE CONTROL INOPERATIVE AND AEB/FEB WARNING LIGHT ON OR RADAR OBSTRUCTION MESSAGE DISPLAYED WITH DTC C1A16 OR C2582 IF YOU CONFIRM IMPORTANT: The purpose of ACTION (on the next page) is to give you a quick idea of the work you will be performing. You MUST closely follow the entire SERVICE PROCEDURE as it contains information that is essential to successfully completing this repair. Nissan Bulletins are intended for use by qualified technicians, not 'do-it-yourselfers'. Qualified technicians are properly trained individuals who have the equipment, tools, safety instruction, and know-how to do a job properly and safely. NOTE: If you believe that a described condition may apply to a particular vehicle, DO NOT assume that it does. See your Nissan dealer to determine if this applies to your vehicle. The customer states that the ICC stopped working while driving, OR The customer states that the AEB/FEB warning light is ON, or turned ON, while driving (Figure 1), OR The message “Unavailable Front Radar Obstruction” or “Forward Driving Aids Temporarily Disabled Front Sensor Blocked See Owner's Manual” has displayed while driving (Figure 2). AND DTC C1A16, C1A16-97, C2582, or C2582-97 is the ONLY DTC stored. Figure 1 Figure 2 This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin. Forward Driving Aids Temporarily Disabled Front Sensor Blocked See Owner’s Manual

NTB19-042F

Service Bulletin/Repair Instructions

AUTOMATIC EMERGENCY BRAKING WARNING LIGHT BLINKING APPLIED SYSTEMS: Vehicles equipped with a lane camera (see Figure 1) SERVICE INFORMATION If the Automatic Emergency Braking (AEB) warning light or is blinking (but not illuminated steadily) or the customer states it is blinking, and there are no related DTCs, inspect the windshield. A blinking AEB warning light may occur under the following conditions:  When contamination or foreign material adhere to the lane camera viewing window on the windshield.  When driving while it is snowing or when frost forms on the lane camera viewing window on the windshield.  When the lane camera viewing window on the windshield is temporarily fogged up. Figure 1 Nissan Bulletins are intended for use by qualified technicians, not 'do-it-yourselfers'. Qualified technicians are properly trained individuals who have the equipment, tools, safety instruction, and know-how to do a job properly and safely. NOTE: If you believe that a described condition may apply to a particular vehicle, DO NOT assume that it does. See your Nissan dealer to determine if this applies to your vehicle. HINT: o Refer to the applicable ESM for diagnosis if DTCs are present in the Laser/Radar, ICC/ADAS, or Lane Camera systems. o For further information:  Refer to the following pages.  Use the search keyword “blinking” in the ESM.

NTB18-041E

Service Bulletin/Repair Instructions

FALSE ACTIVATION OF AEB, FEB, OR FCW IF YOU CONFIRM The following system(s) falsely activated or the customer reports false activation of:  AEB (Automatic Emergency Braking);  FEB (Forward Emergency Braking);  FCW (Forward Collision Warning) ACTION 1. Check Service COMM or Dealer Business Systems (DBS) National Service History to determine if campaign NTB19-064 applies to this vehicle. If the campaign IS applicable to the vehicle you are working on, then this bulletin does NOT apply. ONLY perform campaign NTB19-064. 2. Refer to Repair Overview on page 2. IMPORTANT: The purpose of ACTION (above) is to give you a quick idea of the work you will be performing. You MUST closely follow the entire SERVICE PROCEDURE as it contains information that is essential to successfully completing this repair.

NTB20-066C

Service Bulletin/Repair Instructions

LANE CAMERA AIMING VEHICLE REFERENCE VALUES NOT IN ESM SERVICE INFORMATION If the lane camera requires aiming, the values in Table A on page 4 must be used.  For all other models/model years, consult the Electronic Service Manual (ESM).

NTB19-071D

Service Bulletin/Repair Instructions

DTC B00A0-00 STORED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin. IF YOU CONFIRM DTC B00A0-00 (OCCUPANT DETECTION SENSOR UNIT) is stored, AND OCS zero point reset cannot be performed, (continued on the next page)

NTB12-103I

Service Bulletin/Repair Instructions

CVT/TCM CALIBRATION DATA “WRITE” PROCEDURE This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB10-066C

Service Bulletin/Repair Instructions

CAN COMMUNICATION CODES – DIAGNOSTIC TIPS AND GUIDELINES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB13-027D

Service Bulletin/Repair Instructions

CAN COMMUNICATION – NETWORK DIAGNOSTIC FLOW CHART This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB13-107G

Service Bulletin/Repair Instructions

VEHICLE KEY NOT DETECTED / AUTHENTICATED, ENGINE WILL NOT START This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB21-106B

Service Bulletin/Repair Instructions

DTC C1A17-49 OR C2580-49 STORED IN LASER/RADAR This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB09-081K

Service Bulletin/Repair Instructions

WINDSHIELD CRACKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB13-028I

Service Bulletin/Repair Instructions

REMOVING FOREIGN MATERIAL FROM THE WINDOW GLASS This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB17-019H

Service Bulletin/Repair Instructions

WINDOW GLASS WARRANTY INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB19-042E

Service Bulletin/Repair Instructions

AUTOMATIC EMERGENCY BRAKING WARNING LIGHT BLINKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB23-018G

Service Bulletin/Repair Instructions

SOFTWARE UPDATE FOR INFOTAINMENT ISSUES This bulletin is no longer active. To access infotainment software updates via the Infotainment Software Update Utility: Select SPECIALTY TOOLS, and then select Infotainment Software Updates on the left side of ASIST. Please discard previous versions of NTB23-018.

NTB18-031F

Service Bulletin/Repair Instructions

NISSANCONNECT NAVIGATION SYSTEM SOFTWARE UPDATE TO RESOLVE SEVERAL ISSUES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB23-018F

Service Bulletin/Repair Instructions

SOFTWARE UPDATE FOR INFOTAINMENT ISSUES This bulletin is no longer active. To access infotainment software updates via the Infotainment Software Update Utility: Select SPECIALTY TOOLS, and then select Infotainment Software Updates on the left side of ASIST. HINT: Initially, the Infotainment Software Update Utility will be available only on the CONSULT PC version of ASIST. The Utility will be added to ASIST WEB at a later date. Please discard previous versions of NTB23-018.

NTB17-003F

Service Bulletin/Repair Instructions

FLUID LEAK CAUSED BY TRANSFER ASSEMBLY RIGHT SIDE DRIVE SHAFT OIL SEAL This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB21-094B

Service Bulletin/Repair Instructions

TRANSFER ASSEMBLY SEAL REPLACEMENT FOR AWD FRONT DRIVE SHAFT REMOVAL This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB08-097L

Service Bulletin/Repair Instructions

DIAGNOSIS OF VEHICLE PULL (DRIFT) AND/OR STEERING WHEEL OFF-CENTER This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB23-067

Service Bulletin/Repair Instructions

2014-2020 ROGUE & 2017-2022 ROGUE SPORT; REPLACEMENT JACKKNIFE (FLIP STYLE) KEYS SERVICE INFORMATION For the APPLIED VEHICLES listed above:  If the jackknife key is replaced with 80560-4BA1E, the new part provided will no longer be equipped with a key blade.  New service parts will have a keyless entry remote with a separate mechanical key.  Each vehicle can have a maximum of four (4) keys registered to the BCM. Each service part contains one (1) key and one (1) remote and will use two (2) of the available slots.  Follow the SERVICE PROCEDURE starting on page 2 to register the new mechanical key and remote.

NTB23-018E

Service Bulletin/Repair Instructions

SOFTWARE UPDATE FOR INFOTAINMENT ISSUES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB23-018D

Service Bulletin/Repair Instructions

SOFTWARE UPDATE FOR INFOTAINMENT ISSUES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB23-049

Service Bulletin/Repair Instructions

12 VOLT BATTERY TESTING FOR IN-SERVICE VEHICLES SERVICE INFORMATION The following Service Information lists NNA procedural recommendations for establishing good connections while performing 12V battery testing. These recommendations are expected to promote uniformity during the connection process, therefore reducing the number of incorrect “Test with DCA” and “Replace” results. HINT: If 12 volt batteries are allowed to discharge for a prolonged period of time, battery life may be drastically reduced. This condition may lead to premature battery replacement and customer dissatisfaction. IMPORTANT:  CPX-900 is now an accepted testing tool to use along with or in place of the DSS-5000  CPX-900 operating instructions are found at: https://nissancpx900.midtronics.com/  DSS-5000 operating instructions are found at: https://nissandss5000.midtronics.com/  DCA-8000 is now a required testing tool to be used for all warranty replacement decisions. The DCA-8000 is also a more efficient charger than previously available, and will charge any available 12 volt lead acid battery safely and accurately as long as all precautions and inputs are made correctly. The DCA-8000 operating instructions are found at: https://nissandca8000.midtronics.com/

NTB23-053

Service Bulletin/Repair Instructions

SILICONE-BASED LUBRICANT OR GREASE CAN DAMAGE ELECTRICAL COMPONENTS SERVICE INFORMATION Do not apply Silicone-based lubricants or grease to, or around, any interior electrical components. To avoid the risk of death or severe personal injury, do not directly spray Silicone-based lubricant or grease, or inadvertently overspray Silicone-based lubricant or grease onto any interior electrical components. These types of lubricants can be detrimental to the proper operation of electrical components.

NTB12-103H

Service Bulletin/Repair Instructions

CVT/TCM CALIBRATION DATA “WRITE” PROCEDURE This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB13-107F

Service Bulletin/Repair Instructions

VEHICLE KEY NOT DETECTED / AUTHENTICATED, ENGINE WILL NOT START This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB14-012I

Service Bulletin/Repair Instructions

REMOTE ENGINE START NOT WORKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB16-003C

Service Bulletin/Repair Instructions

INTELLIGENT KEY REPLACEMENT OR SWAPPING BETWEEN VEHICLES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.

NTB23-018C

Service Bulletin/Repair Instructions

SOFTWARE UPDATE FOR INFOTAINMENT ISSUES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB03-074Q

Service Bulletin/Repair Instructions

HEADLAMP, FOG LAMP, OR REAR COMBINATION LAMP FOGGING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB18-031E

Service Bulletin/Repair Instructions

NISSANCONNECT NAVIGATION SYSTEM SOFTWARE UPDATE TO RESOLVE SEVERAL ISSUES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB12-055J

Service Bulletin/Repair Instructions

CLICKING NOISE FROM FRONT OR REAR AXLE DURING TAKE-OFF/ACCELERATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB23-018B

Service Bulletin/Repair Instructions

SOFTWARE UPDATE FOR INFOTAINMENT ISSUES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB23-018A

Service Bulletin/Repair Instructions

SOFTWARE UPDATE FOR INFOTAINMENT ISSUES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB18-050A

Service Bulletin/Repair Instructions

VOLUNTARY SERVICE CAMPAIGN 2014-2017 ROGUE; ECM REPROGRAM This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB19-042D

Service Bulletin/Repair Instructions

AUTOMATIC EMERGENCY BRAKING WARNING LIGHT BLINKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB19-071C

Service Bulletin/Repair Instructions

DTC B00A0-00 STORED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB21-106A

Service Bulletin/Repair Instructions

DTC C1A17-49 OR C2580-49 STORED IN LASER/RADAR This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB10-145B

Service Bulletin/Repair Instructions

ABS/VDC CAN DIAGNOSIS INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB23-018

Service Bulletin/Repair Instructions

SOFTWARE UPDATE FOR INFOTAINMENT ISSUES SERVICE INFORMATION When diagnosing an infotainment issue or after replacement of the AV Control Unit, it is necessary to verify the current software version of the AV Control Unit to determine if a software version update is required. Use the vehicle tables in this bulletin to determine the current software version, if the AV Control Unit requires a software version update, and which procedure to use to update the AV Control Unit. The software updates in this bulletin are to address stability improvements and “bug” fixes. IMPORTANT: If the customer is experiencing a software related concern, refer to NTB21-038 to verify if the customer concern is a hardware or software related issue. If the concern is a software related issue, review the information in this bulletin to update the AV Control Unit as needed.

NTB09-081J

Service Bulletin/Repair Instructions

WINDSHIELD CRACKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB13-028H

Service Bulletin/Repair Instructions

REMOVING FOREIGN MATERIAL FROM THE WINDOW GLASS This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB08-097K

Service Bulletin/Repair Instructions

DIAGNOSIS OF VEHICLE PULL (DRIFT) AND/OR STEERING WHEEL OFF-CENTER This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB10-126C

Service Bulletin/Repair Instructions

WHEEL BEARING COLLISION DAMAGE This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB22-101

Service Bulletin/Repair Instructions

DRIVE SHAFT BOOT SERVICE INFORMATION SERVICE INFORMATION If a Drive Shaft (Axle Shaft) Boot on an APPLIED VEHICLE is found to be leaking grease, AND There is no abnormal noise or obvious CV Joint risk due to water intrusion and/or complete grease loss, check for REPAIR KIT-DUST BOOT (CV Joint Boot Kit) availability.  If there is a REPAIR KIT-DUST BOOT (CV Joint Boot Kit) available for the vehicle being repaired, do NOT replace the axle. Install a new boot kit following the procedure in the ESM. o Refer to the ESM: TRANSMISSION & DRIVELINE > FRONT AXLE > REMOVAL AND INSTALLATION > FRONT DRIVE SHAFT BOOT o If the complete axle (drive shaft) is replaced when only a new boot is required, the over-repair may be charged back to the dealer.  If there is NOT a REPAIR KIT-DUST BOOT (CV Joint Boot Kit) available for the vehicle being repaired, refer to the ESM for further diagnostic information. IMPORTANT: When servicing vehicles with staked axle nuts, refer to NTB21-013 to prevent Drive Shaft thread damage.

NTB22-100

Service Bulletin/Repair Instructions

3G TELEMATICS HARDWARE DEACTIVATION SERVICE INFORMATION The APPLIED VEHICLES that come equipped with a factory installed SOS switch, located near the overhead map lamp, also come equipped with a wireless communication device called a Telematics Communication Unit (TCU). AT&T discontinued its U.S. 3G network coverage on February 22, 2022. As a result, automakers that utilize AT&T’s 3G network connection, including Nissan Group, have had connectivity services affected. NissanConnect® Services are no longer available on the APPLIED VEHICLES listed above.

NTB10-029I

Service Bulletin/Repair Instructions

ABNORMAL NOISE, VIBRATION AND/OR BINDING FEELING FROM REAR DIFFERENTIAL This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB12-055I

Service Bulletin/Repair Instructions

CLICKING NOISE FROM FRONT OR REAR AXLE DURING TAKE-OFF/ACCELERATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

REVISION 2 Rogue

Service Bulletin/Repair Instructions

CVT Warranty Extension UPDATE August 30, 2022 Please discard earlier versions of this bulletin. The announcement from June 2, 2022 has been revised to include: • The voucher program ID numbers provided in the FAQ section of this dealer announcement have been changed. The new voucher program ID numbers are:  Nissan program ID: 22N2299CVT  INFINITI program ID: 22I2299CVT

NTB14-012H

Service Bulletin/Repair Instructions

REMOTE ENGINE START NOT WORKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB17-003E

Service Bulletin/Repair Instructions

FLUID LEAK CAUSED BY TRANSFER ASSEMBLY RIGHT SIDE DRIVE SHAFT OIL SEAL This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB21-094A

Service Bulletin/Repair Instructions

TRANSFER ASSEMBLY SEAL REPLACEMENT FOR AWD FRONT DRIVE SHAFT REMOVAL This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

Rogue Pathfinder

Service Bulletin/Repair Instructions

CVT Warranty Extension In an effort to assure customer satisfaction, demonstrate our confidence in continuously variable transmissions (CVTs), and to address customer concerns including those expressed by customers in the class actions, Nissan will extend the warranty coverage on the CVT. The warranty extension includes the CVT assembly and internal CVT components, gaskets, and seals, CVT control valve body, torque converter, cooler kit (if applicable) and reprogramming of the Transmission Control Module (TCM), on the vehicles listed in this announcement. The warranty is being extended from its original duration of 60 months/60,000 miles to 84 months/84,000 miles (whichever occurs first). Coverage of other vehicle components remains unchanged, and all other terms, conditions, limitations and exclusions of Nissan’s New Vehicle Limited Warranty continue to apply. ***** What Dealers Should Do ***** 1. If an owner contacts a dealer with a CVT concern in an owned or leased vehicle, verify warranty coverage for the specific VIN and then inform the customer of any diagnostic charges. NOTE: Some owners may have opted out of the warranty extension by excluding themselves from the class action settlement, thus it is important to check the VIN for each vehicle to verify coverage. 2. Use the appropriate Technical Service Bulletin (TSB) and/or Electronic Service Manual (ESM) to diagnose the root cause of the customer concern and identify the correct repair to resolve the customer concerns. NOTE: Dealers will need to follow the warranty process and obtain pre-approval from the Powertrain Call Center (800-973-9992, option 2) for any vehicles requiring CVT replacements when the replacement cost exceeds a Dealer’s Claims Administration/Authorization Limits (DCAL). Control valves and CVT belt and pulley kits do not require pre-authorization for repairs made under warranty.

NTB10-029H

Service Bulletin/Repair Instructions

NISSAN AWD MODELS; ABNORMAL NOISE, VIBRATION AND/OR JUDDER FROM REAR DIFFERENTIAL This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB19-071B

Service Bulletin/Repair Instructions

DTC B00A0-00 STORED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB22-026

Service Bulletin/Repair Instructions

SERVICE INFORMATION FOR FUEL GAUGE INACCURATE WITH DTCS STORED IN ECM SERVICE INFORMATION If a fuel level sensor has been diagnosed as sending an incorrect level signal, and one or more of the following DTCs are stored in the ECM, do not replace the entire “Fuel Level Sensor Unit, Fuel Filter and Fuel Pump Assembly” (fuel pump assembly). The fuel level sensor can be replaced separately.  P0460 (FUEL LEV SEN SLOSH)  P0461 (FUEL LEVEL SENSOR)  P0462 (FUEL LEVL SEN/CIRC)  P0463 (FUEL LEVL SEN/CIRC) NOTE: Warranty claims referring to fuel level issues that result in the replacement of the entire fuel pump assembly will be charged back.

2014-2018 Rogue

Service Bulletin/Repair Instructions

Continuously Variable Transmission (CVT) Class Action Owner Notification On March 23, 2022, the Court presiding over a class action lawsuit gave final approval to a proposed settlement under which the CVT warranty will be extended for the following vehicles: 2014-2018 Rogue 2015-2018 Pathfinder *Not including Rogue Hybrid or Pathfinder Hybrid vehicles The approved settlement and the warranty extension are expected to become effective by June 1, 2022. Additional communication will be distributed prior to the warranty extension going into effect. To be clear, for the time being there is no warranty extension, and you should proceed with CVT-related claims as outlined below in bullet point three (3) under What Dealers Should Do. ***** What Dealers Should Do ***** 1. No action is necessary at this time. Nissan will provide additional instructions prior to the effective date of the extended warranty, which is expected to be June 1, 2022. 2. If a customer contacts the dealer with a CVT concern in an owned or leased vehicle, dealers should use the appropriate Technical Service Bulletin (TSB) to diagnose the root cause of the customer concern and identify the correct repair to resolve the customer concerns. NOTE: Dealers will need to follow the warranty process and obtain pre-approval from the Powertrain Call Center (800-973-9992 Option 2) for any vehicles requiring CVT assemblies to be replaced. Valve bodies and CVT belt and pulley kits do not require pre-authorization. 3. If the vehicle is no longer covered by a powertrain or parts warranty, provide owners a repair estimate for test drive, diagnosis, and repair after consulting the goodwill guidelines available in the Assurance Product Resources Manual (APRM) or WBP/18-006.

NTB10-029G

Service Bulletin/Repair Instructions

NISSAN AWD MODELS; ABNORMAL NOISE, VIBRATION AND/OR JUDDER FROM REAR DIFFERENTIAL This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB15-049X

Service Bulletin/Repair Instructions

TELEMATICS SERVICE INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB17-003D

Service Bulletin/Repair Instructions

FLUID LEAK CAUSED BY TRANSFER ASSEMBLY RIGHT SIDE DRIVE SHAFT OIL SEAL This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB13-027C

Service Bulletin/Repair Instructions

CAN COMMUNICATION – NETWORK DIAGNOSTIC FLOW CHART This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB17-003C

Service Bulletin/Repair Instructions

FLUID LEAK CAUSED BY TRANSFER ASSEMBLY RIGHT SIDE DRIVE SHAFT OIL SEAL This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB13-097J

Service Bulletin/Repair Instructions

EVAP LEAK DTC P0442, P0455, P0456 INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB17-082E

Service Bulletin/Repair Instructions

DTC P0456 CAUSED BY EVAP LEAK AT VENT CONTROL VALVE O-RING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB16-110Q

Service Bulletin/Repair Instructions

2013-2017 ALTIMA AND 2014-2017 ROGUE; 4 CYLINDER WITH DTC P17F0, P17F1, P0776, P2813, P1715, AND/OR P0841 STORED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB17-045C

Service Bulletin/Repair Instructions

CLEANING FRONT OR REAR COMBINATION LAMP ASSEMBLIES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB99-001F

Service Bulletin/Repair Instructions

STRUT AND SHOCK ABSORBER REPLACEMENT GUIDELINES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB21-106

Service Bulletin/Repair Instructions

DTC C1A17-49 OR C2580-49 STORED IN LASER/RADAR SERVICE INFORMATION If DTC C1A17-49 or C2580-49 is stored in LASER/RADAR in the “PAST” column:  Erase the DTC.  DO NOT replace any parts. If DTC C1A17-49 or C2580-49 is stored in LASER/RADAR in the "CURRENT" column, refer to the applicable ESM for instructions.

NTB18-031D

Service Bulletin/Repair Instructions

2016-2018 NISSANCONNECT NAVIGATION SYSTEM SOFTWARE UPDATE TO RESOLVE SEVERAL ISSUES This bulletin has been amended. See AMENDMENT HISTORY on page 14. Please discard previous versions of this bulletin.

NTB21-094

Service Bulletin/Repair Instructions

TRANSFER ASSEMBLY SEAL REPLACEMENT FOR AWD FRONT DRIVE SHAFT REMOVAL SERVICE INFORMATION When removing the front passenger (RH) side drive shaft on an applied vehicle for any reason, transfer assembly drive shaft oil seal and dust cover seal replacement is required. Refer to the SERVICE PROCEDURE in this bulletin.

NTB18-055E

Service Bulletin/Repair Instructions

CVT FLUID LEVEL QUICK CHECK GAUGE This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB12-055H

Service Bulletin/Repair Instructions

CLICKING NOISE FROM FRONT OR REAR AXLE DURING TAKE-OFF/ACCELERATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB15-077D

Service Bulletin/Repair Instructions

SIGNAL TECH-II INTELLIGENT KEY BATTERY TEST AND SIGNAL CHECK This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB16-028D

Service Bulletin/Repair Instructions

INTELLIGENT KEY BUTTONS INOPERATIVE BUT REQUEST SWITCHES WORK This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB17-003B

Service Bulletin/Repair Instructions

FLUID LEAK CAUSED BY TRANSFER ASSEMBLY RIGHT SIDE DRIVE SHAFT SEAL This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB21-035

Service Bulletin/Repair Instructions

2018-2021 LEAF AND 2017-2020 ROGUE; STEERING WHEEL CHROME FINISHER REPLACEMENT SERVICE INFORMATION If the chrome finisher on the steering wheel needs to be replaced, the chrome finisher can be ordered separately from the steering wheel. SERVICE PROCEDURE 1. Remove the driver side air bag module.  For removal of the driver side air bag module, refer to the Electronic Service Manual (ESM), section REPAIR – RESTRAINTS – SRS AIRBAG – REMOVAL AND INSTALLATION – DRIVER AIR BAG MODULE. NOTE:  When removing the chrome finisher from the steering wheel, reference Figure 2 for the 6 attachment points.  During removal of the chrome finisher (step 2 on page 3), pull on the chrome finisher just enough to release the pawls from the steering wheel.

NTB16-018D

Service Bulletin/Repair Instructions

MIL ON WITH P0603 STORED FOR ECM BACK UP CIRCUIT This bulletin has been amended. See AMENDMENT HISTORY on page 3. Please discard previous versions of this bulletin.

NTB15-049W

Service Bulletin/Repair Instructions

TELEMATICS SERVICE INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB18-008A

Service Bulletin/Repair Instructions

ADAS SYSTEM DTC C1A03, C1A04, AND/OR C1B01 SERVICE INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB18-041D

Service Bulletin/Repair Instructions

2017-2020 ROGUE, ROGUE HYBRID, AND ROGUE SPORT; FALSE ACTIVATION OF AEB, FEB, OR FCW This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB13-106G

Service Bulletin/Repair Instructions

CORRECT OPERATION OF AUDIO CONTROLS AND BACK-UP CAMERA REQUIRES CONFIGURATION WITH C-III PLUS This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.

NTB13-099G

Service Bulletin/Repair Instructions

AUDIO UNIT REPLACEMENT - VEHICLES WITH COLOR DISPLAY AUDIO AND NAVIGATION SYSTEM This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin

NTB15-077C

Service Bulletin/Repair Instructions

NISSAN; SIGNAL TECH-II INTELLIGENT KEY BATTERY TEST AND SIGNAL CHECK This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB16-028C

Service Bulletin/Repair Instructions

INTELLIGENT KEY BUTTONS INOPERATIVE BUT REQUEST SWITCHES WORK This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB17-014A

Service Bulletin/Repair Instructions

BLUETOOTH, USB, AND AUX FUNCTION DIAGNOSTIC TOOL This bulletin has been amended. See AMENDMENT HISTORY on page 3. Please discard previous versions of this bulletin.

NTB17-097B

Service Bulletin/Repair Instructions

2016-2018 ROGUE AND 2017-2018 ROGUE SPORT; WHISTLE NOISE TRANSMITTED TO CALL RECIPIENT WHEN USING BLUETOOTH HANDS-FREE PHONE SYSTEM This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB19-071A

Service Bulletin/Repair Instructions

DTC B00A0-00 STORED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB15-013f

Service Bulletin/Repair Instructions

NISSAN; PROCEDURE TO CLEAN CVT TRANSMISSION FLUID COOLERS This bulletin is no longer active. Please discard previous versions of NTB15-013. Refer to the ESM for the fluid cooler cleaning procedure.

NTB16-110p

Service Bulletin/Repair Instructions

2013-2017 ALTIMA AND 2014-2017 ROGUE; 4 CYLINDER WITH DTC P17F0, P17F1, P0776, P2813, P1715, AND/OR P0841 STORED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB99-001e

Service Bulletin/Repair Instructions

STRUT AND SHOCK ABSORBER REPLACEMENT GUIDELINES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB18-031c

Service Bulletin/Repair Instructions

2016-2018 NISSAN CONNECT NAVIGATION SYSTEM SOFTWARE UPDATE TO RESOLVE SEVERAL ISSUES This bulletin has been amended. See AMENDMENT HISTORY on page 9. Please discard previous versions of this bulletin.

NTB19-031a

Service Bulletin/Repair Instructions

BEEPING NOISE WHILE TRAVELING THROUGH OPEN AREA This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB19-042b

Service Bulletin/Repair Instructions

AEB WARNING LIGHT BLINKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB19-064c

Service Bulletin/Repair Instructions

VOLUNTARY SERVICE CAMPAIGN 2017-2018 ROGUE, ROGUE HYBRID, AND ROGUE SPORT; ICC/ADAS AND LASER/RADAR REPROGRAMMING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB20-066b

Service Bulletin/Repair Instructions

LANE CAMERA AIMING VEHICLE REFERENCE VALUES NOT IN ESM This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB15-049v

Service Bulletin/Repair Instructions

TELEMATICS SERVICE INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB20-043a

Service Bulletin/Repair Instructions

2014-2020 ROGUE; AIR DUCT REPLACEMENT This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB14-105a

Service Bulletin/Repair Instructions

2014-2020 ROGUE; CARPET WET FRONT FLOOR AREA This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.

NTB12-110d

Service Bulletin/Repair Instructions

POWER BACK DOOR CALIBRATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.

NTB20-094

Service Bulletin/Repair Instructions

2015-2020 ROGUE; MIL ON WITH DTC P0181 AND/OR P0183 IF YOU CONFIRM The MIL is ON with DTC P0181 (FTT SENSOR) and/or P0183 (FTT SEN/CIRCUIT) stored in the ECM. ACTION 1. Remove the fuel pump assembly. 2. Inspect the fuel pump assembly wiring, and reroute the wiring, if applicable. 3. Reinstall the fuel pump assembly.

NTB17-083b

Service Bulletin/Repair Instructions

MOTION ACTIVATED LIFTGATE STICKER This bulletin is no longer active. Please discard previous versions of NTB17-083.

NTB20-090a

Service Bulletin/Repair Instructions

2014-2020 ROGUE; HVAC BLOWER NOISY OR WATER DRIPS ON DRIVER SIDE CARPET This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB20-090

Service Bulletin/Repair Instructions

2014-2020 ROGUE; HVAC BLOWER NOISY OR WATER DRIPS ON DRIVER SIDE CARPET IF YOU CONFIRM The customer states the HVAC blower is noisy OR Water is dripping on the driver side carpet after going through a car wash. ACTION Refer to REPAIR OVERVIEW on page 2.

NTB15-026d

Service Bulletin/Repair Instructions

2014-2020 ROGUE; LACKS POWER DUE TO SNOW INGESTION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

DOR-H5Y5B-01

Service Bulletin/Repair Instructions

This SKU is a Suspension Ball Joint. The customer communication requested return of unsold inventory to inspect for the outer diameter of the ball joint housing being too small. The outer diameter being too small would prevent the part from being installed, and would therefore have no impact on the end user besides time to complete installation.

NTB19-042a

Service Bulletin/Repair Instructions

AEB WARNING LIGHT BLINKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB20-075

Service Bulletin/Repair Instructions

SOFTWARE UPDATE POP-UP NOTIFICATION SERVICE INFORMATION The infotainment system of the applied vehicle has the ability to update its software through an over-the-air (OTA) link. As software updates become available for new features, and/or patches, the software update screen (pop-up) shown in Figure 1 will automatically be displayed. Much like cell phone and computer updates, this is a normal feature which allows the user to choose when an update is downloaded.  It is recommended that while in dealer inventory and this pop-up appears, that “ Yes” is selected to provide the latest software version to the customer at delivery. NOTE: If the ignition is turned OFF in the middle of a download, it will automatically restart when the ignition is turned back ON. When one of the following is selected: Yes…..The pop-up is hidden and the download starts in the background. Later…The pop-up is hidden and displayed again in the next key cycle (after cold start).

NTB20-066a

Service Bulletin/Repair Instructions

LANE CAMERA AIMING VEHICLE REFERENCE VALUES NOT IN ESM This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB20-069

Service Bulletin/Repair Instructions

ROGUE AND ROGUE SPORT; VIBRATION AND/OR NOISE WHEN MAKING LOW SPEED TURNS IF YOU CONFIRM There is a vibration or judder feeling from the rear of the vehicle during the following conditions:  When making turns  On dry roads  At low speeds (under 40 MPH) And  The above vibration does not occur if the electric controlled coupling is electrically disconnected. ACTION 1. Confirm the AWD control unit part number, and replace it, if applicable. 2. Replace the electric controlled coupling for the rear final drive. 3. Perform Unit Characteristics Writing.

NTB20-066

Service Bulletin/Repair Instructions

LANE CAMERA AIMING VEHICLE REFERENCE VALUES NOT IN ESM SERVICE INFORMATION If the lane camera requires aiming, the values in Table A on page 4 must be used.  For all other models/model years, consult the Electronic Service Manual (ESM). The following CONSULT-III plus (C-III plus) figures and steps are only provided to indicate where the VEHICLE REFERENCE VALUE from Table A is to be entered. The entire camera aiming procedure must be followed to complete the aiming procedure.  Refer to the ESM section: CRUISE CONTROL & DRIVER ASSISTANCE > DRIVER ASSISTANCE SYSTEM > DRIVER ASSISTANCE SYSTEM > BASIC INSPECTION > LANE CAMERA UNIT > CAMERA AIMING ADJUSTMENT. 1. Turn the ignition ON. 2. From the C-III plus home screen, select Diagnosis (One System).

NTB18-033b

Service Bulletin/Repair Instructions

ACCELERATOR PEDAL VIBRATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB20-043

Service Bulletin/Repair Instructions

2015-2020 ROGUE; AIR DUCT REPLACEMENT IF YOU CONFIRM Air duct 1, air duct 2, or the air cleaner cover shown in Figure 1 needs to be replaced. ACTION Inspect for a clip in the location shown in Figure 1 and Figure 2.  If a clip is present, then the vehicle IS equipped with the updated parts; no further action is needed. Individual parts may be replaced as needed.  If a clip is NOT present, then the vehicle is equipped with older parts. See SERVICE PROCEDURE on the next page.

NTB15-049u

Service Bulletin/Repair Instructions

TELEMATICS SERVICE INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB16-110o

Service Bulletin/Repair Instructions

2013-2017 ALTIMA AND 2014-2017 ROGUE; 4 CYLINDER WITH DTC P17F0, P17F1, P0776, P2813, P1715, AND/OR P0841 STORED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB17-003a

Service Bulletin/Repair Instructions

FLUID LEAK CAUSED BY TRANSFER ASSEMBLY RIGHT SIDE DRIVE SHAFT SEAL This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB18-055d

Service Bulletin/Repair Instructions

CVT FLUID LEVEL QUICK CHECK GAUGE This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB16-110n

Service Bulletin/Repair Instructions

2013-2017 ALTIMA AND 2014-2017 ROGUE; 4 CYLINDER WITH DTC P17F0, P17F1, P0776, P2813, P1715, AND/OR P0841 STORED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB15-049t

Service Bulletin/Repair Instructions

TELEMATICS SERVICE INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB12-055g

Service Bulletin/Repair Instructions

CLICKING NOISE FROM FRONT OR REAR AXLE DURING TAKE-OFF/ACCELERATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB17-057c

Service Bulletin/Repair Instructions

2015-2020 ROGUE AND 2017-2020 ROGUE SPORT; DISTANCE TO EMPTY DOES NOT RESET This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB15-013e

Service Bulletin/Repair Instructions

NISSAN; PROCEDURE TO CLEAN CVT TRANSMISSION FLUID COOLERS This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB19-080

Service Bulletin/Repair Instructions

2014-2020 ROGUE; NO AIR FLOW FROM VENTS DUE TO SNOW BUILD-UP IF YOU CONFIRM Or the customer states there is no air flow from any of the HVAC vents And There is snow build-up in and around the blower motor air inlet, behind the cowl. ACTION 1. Remove all snow, water, and debris from the blower motor inlet, cowl area, and where the blower motor mounts. 2. Clean or replace the blower motor as needed. 3. If the blower motor does not work on all speed settings, replace the variable blower control (fan resistor). 4. If not already equipped: Install the cowl and wiper pivot filters listed in PARTS INFORMATION on the last page of this bulletin.

White Paint Clas

Service Bulletin/Repair Instructions

White Paint Class Action Owner Notification Dealer Notification In October, owners of white Nissan Rogues produced between January 11, 2013 and April 23, 2013, will receive a notice from a settlement administrator informing them of the terms of a proposed class action settlement. The settlement, if approved by the presiding court, could extend the warranty on the paint for four years and provide a one-time full vehicle repaint (subject to a copay). Eligible owners can also obtain coverage for any reasonable and necessary rental car coverage arising from the repaint, or reimbursement of amounts previously incurred for a one-time repaint and any reasonable and necessary rental car services arising from the repaint. The settlement also provides for eligibility in Nissan’s Vehicle Purchase Program. To be clear, unless and until the proposed settlement is approved by the presiding court, there is no warranty extension or other remedy and you should proceed with paint-related claims in the ordinary course. The proposed settlement, and the associated potential warranty extension, include many terms and conditions. Rather than attempting to address questions about the proposed settlement terms from customers, Nissan recommends dealers refer customers to the website listed below. This will enable owners to receive information from appropriate sources and avoid providing incorrect and/or incomplete information to customers. The website is currently live and available to inquiring customers. ***** What Dealers Should Do ***** 1. No action is necessary at this time. Nissan will provide additional instructions once the proposed settlement is approved by the court. 2. If a customer contacts the dealer with a white paint concern and/or references this settlement notification, dealers should refer the customer to the third party administrator’s website for additional information. www.vehiclepaintsettlement.com

NTB17-028a

Service Bulletin/Repair Instructions

2014-2020 ROGUE; BLOWER MOTOR SERVICE INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB16-110m

Service Bulletin/Repair Instructions

2013-2017 ALTIMA AND 2014-2017 ROGUE; 4 CYLINDER WITH DTC P17F0, P17F1, P0776, P2813, P1715, AND/OR P0841 STORED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB19-064b

Service Bulletin/Repair Instructions

VOLUNTARY SERVICE CAMPAIGN 2017-2018 ROGUE, ROGUE HYBRID, AND ROGUE SPORT; ICC/ADAS AND LASER/RADAR REPROGRAMMING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB19-072

Service Bulletin/Repair Instructions

TRANSMISSION RANGE SWITCH SERVICE INFORMATION SERVICE INFORMATION The transmission range switch of the APPLIED VEHICLES listed above is now available as a separate service part. If the transmission range switch of an APPLIED VEHICLE is being replaced for any reason, it must be adjusted after its replacement.  Refer to SERVICE PROCEDURE on page 3 for transmission range switch removal, installation, and adjustment.

NTB19-071

Service Bulletin/Repair Instructions

DTC B00A0-00 STORED IF YOU CONFIRM DTC B00A0-00 (OCCUPANT DETECTION SENSOR UNIT) is stored And OCS zero point reset cannot be performed (continued on the next page) And The following screen displays: ACTION 1. Check the Occupant Classification System (OCS) control unit using the ODS Analysis tool software.  Refer to SERVICE PROCEDURE on page 5. HINT: “OCS” may also be referred to as “ODS”. 2. Perform “75-zero RESET”.

NTB19-064a

Service Bulletin/Repair Instructions

VOLUNTARY SERVICE CAMPAIGN 2017-2018 ROGUE, ROGUE HYBRID, AND ROGUE SPORT; ICC/ADAS AND LASER/RADAR REPROGRAMMING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB18-041c

Service Bulletin/Repair Instructions

2017-2020 ROGUE, ROGUE HYBRID, AND ROGUE SPORT; FALSE ACTIVATION OF AEB, FEB, OR FCW This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB17-113b

Service Bulletin/Repair Instructions

2017-2018 ROGUE SPORT; WHEN COLD LONG CRANK TIME, ENGINE TURNS OFF, HESITATION, ROUGH IDLE, OR MISFIRE This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NPSB18-443B AEB

Service Bulletin/Repair Instructions

2017-2018 Rogue and Rogue Sport Automatic Emergency Braking (AEB) Update Notification Letter REVISED August 27, 2019 Please discard earlier versions of this bulletin. This bulletin has been superseded by campaign ID P9327. Please refer to the Voluntary Service Campaign announcement associated with this campaign ID for additional information.

P9327 Rogue - Au

Service Bulletin/Repair Instructions

Automatic Emergency Braking (AEB) Voluntary Service Campaign ***** Campaign Summary***** Nissan is committed to the safety, security and satisfaction of our customers and their passengers. Nissan is upgrading an existing Customer Service Initiative to a Voluntary Service Campaign on certain Model Year 2017-18 Rogue (T32), Rogue Sport (J11), and Rogue Hybrid (T32H) vehicles to reprogram the Radar and Advanced Driver Assistance System (ADAS) components of the Automatic Emergency Braking (AEB) system. Covered vehicles that were not updated under NPSB/18-443 will be reprogrammed with updated software to improve system functionality through reduced false positive AEB activation in certain driving environments. In rare instances and unique roadway environments such as certain types of railroad crossings and metal overpasses, the AEB system in some vehicles may activate braking when it is not needed. The driver can always override the AEB system by pressing the accelerator. Nissan previously invited customers that had experienced an issue with their AEB system to come in for updated software before their Limited Vehicle Warranty expired. Now, Nissan is encouraging owners to have this important software update performed without regard to any issues or warranty status. ***** What Dealers Should Do ***** 1. Verify if vehicles are affected by this Voluntary Service Campaign using Service Comm or DBS National Service History - Open Campaign I.D. P9327. 2. Dealers should reprogram the Radar and ADAS software on any affected vehicles in retailer new or pre-owned inventory to help ensure customer satisfaction. 3. Dealers should use NTB19-064 to inspect and, if necessary, remedy any vehicles subject to this campaign. 4. The service department should submit the applicable warranty claim for the action performed so it can be closed on Service Comm and release the vehicle.

NTB19-064

Service Bulletin/Repair Instructions

VOLUNTARY SERVICE CAMPAIGN 2017-2018 ROGUE, ROGUE HYBRID, AND ROGUE SPORT; ICC/ADAS AND LASER/RADAR REPROGRAMMING INTRODUCTION Nissan is conducting this voluntary service campaign on certain specific model year 2017-2018 Rogue, Rogue Hybrid, and Rogue Sport vehicles to reprogram the Laser/Radar and/or ICC/ADAS control units. This service will be performed at no charge to the customer for parts or labor. IDENTIFICATION NUMBER Nissan has assigned identification number P9327 to this campaign. This number must appear on all communication and documentation of any nature dealing with this campaign. DEALER RESPONSIBILITY Dealers are to repair vehicles falling within range of this campaign that enter the service department. This includes vehicles purchased from private parties, vehicles presented by transient (tourists) owners, and vehicles in a dealer’s inventory.

NTB14-012e

Service Bulletin/Repair Instructions

REMOTE ENGINE START NOT WORKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB18-077a

Service Bulletin/Repair Instructions

MIL ON WITH DTC P0776, P1715 AND MAY HAVE HESITATION AND/OR LACK OF POWER This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB15-049s

Service Bulletin/Repair Instructions

TELEMATICS SERVICE INFORMATION This bulletin applies only to vehicles equipped with a Telematics Communication Unit (TCU). This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB19-045

Service Bulletin/Repair Instructions

MIL ON WITH DTC P0087, P0101, P0448, OR P2008 IF YOU CONFIRM An applied vehicle has a stored DTC shown in Table A on the next page, AND The ECM part number is shown in Table B, starting on page 3. ACTION First, perform the appropriate diagnostic procedure for the stored code to repair the vehicle according to the Electronic Service Manual (ESM), AND Reprogram the ECM after performing the diagnosis and repair.

NTB18-019a

Service Bulletin/Repair Instructions

2013-2018 ALTIMA AND 2014-2018 ROGUE; ENGINE SUPPORT TOOLS This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB18-055c

Service Bulletin/Repair Instructions

CVT FLUID LEVEL QUICK CHECK GAUGE This bulletin applies only to vehicles equipped with a Continuously Variable Transmission (CVT). This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB19-042

Service Bulletin/Repair Instructions

AEB WARNING LIGHT BLINKING This bulletin applies only to vehicles equipped with a lane camera. SERVICE INFORMATION If the AEB warning light is blinking (but not illuminated steadily) or the customer states it is blinking, and there are no related DTCs, inspect the windshield. A blinking AEB warning light may occur under the following conditions: - When contamination or foreign material adhere to the lane camera viewing window on the windshield - When driving while it is snowing or when frost forms on the lane camera viewing window on the windshield - When the lane camera viewing window on the windshield is temporarily fogged up NOTE: - If DTCs are present in any of the following related systems: - Laser/Radar, - ICC/ADAS, or - Lane Camera, Refer to the related Electronic Service Manual (ESM) for diagnosis. - Refer to the following pages for further information.

NTB19-039

Service Bulletin/Repair Instructions

2017 ? 2018 ROGUE SPORT; AIR DUCT REPLACEMENT IF YOU CONFIRM If air duct 1, air duct 2, or air cleaner cover shown in Figure 1 need to be replaced ACTION Inspect for a clip in the location shown in Figure 1 and Figure 2. - If a clip is present, then the vehicle IS equipped with the updated parts; no further action is needed. Individual parts may be replaced as needed. - If a clip is NOT present, then the vehicle is equipped with older parts. See SERVICE PROCEDURE on the next page.

NTB19-031

Service Bulletin/Repair Instructions

BEEPING NOISE WHILE TRAVELING THROUGH OPEN AREA IF YOU CONFIRM Customer reports continuous beeping noise and/or the Driving Aids screen shown in Figure 1 flashes, especially when driving in open areas similar to Figure 2. ACTION Refer to TABLE A on page 8 to confirm if ICC/ADAS 2 control unit reprogramming is needed.

NTB12-100b

Service Bulletin/Repair Instructions

CVT / TCM CALIBRATION DATA ?WRITE? PROCEDURE This bulletin applies only to vehicles equipped with a Continuously Variable Transmission (CVT). This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB12-103g

Service Bulletin/Repair Instructions

CVT / TCM CALIBRATION DATA ?WRITE? PROCEDURE This bulletin applies only to vehicles equipped with a Continuously Variable Transmission (CVT). This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB15-102b

Service Bulletin/Repair Instructions

2013-2017 ALTIMA AND 2014-2017 ROGUE; WHINE NOISE FROM CVT AT HIGHWAY SPEEDS This bulletin applies only to vehicles equipped with a QR25DE (4-cyl) engine. This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.

NTB18-055b

Service Bulletin/Repair Instructions

CVT FLUID LEVEL QUICK CHECK GAUGE This bulletin applies only to vehicles equipped with a Continuously Variable Transmission (CVT). This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.

NTB18-041b

Service Bulletin/Repair Instructions

2017-2018 ROGUE, ROGUE HYBRID, AND ROGUE SPORT; FALSE ACTIVATION OF AEB, FEB, OR FCW This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NPSB18-443a

Service Bulletin/Repair Instructions

2017-2018 Rogue and Rogue Sport Automatic Emergency Braking (AEB) Update Notification Letter Nissan is conducting an important Customer Service Initiative to increase awareness of an available update for the Automatic Emergency Braking (AEB) system on certain Model Year 2017-18 Rogue (T32), Rogue Sport (J11), and Rogue Hybrid (T32) vehicles. In rare instances and unique roadway environments such as certain types of railroad crossings and metal overpasses, the AEB system in some vehicles may activate braking when not needed. The driver can always override the AEB system by pressing the accelerator. Nissan has developed a special AEB system update that is available to owners at no cost for parts and labor during the duration of the Basic Coverage under their New Vehicle Limited Warranty (3 years/36,000 miles, whichever comes first). This update will enhance system performance for customers that wish to proactively update their vehicle or for customers that have experienced this issue. THIS CUSTOMER SERVICE INITIATIVE IS IMPLEMENTED TO MAKE CUSTOMERS AWARE OF AN AVAILABLE UPDATE. THIS INITIATIVE IS NOT A WARRANTY, AN EXTENSION OF THE NEW VEHICLE LIMITED WARRANTY, OR AN IMPLIED OR GENERAL WARRANTY, AND IS NOT CONNECTED TO ANY SALE OF THE VEHICLE.

NTB19-022

Service Bulletin/Repair Instructions

NISSAN; P0171 AND P0174 SERVICE INFORMATION SERVICE INFORMATION Diagnosis for DTCs P0171 (FUEL SYS LEAN B1) and P0174 (FUEL SYS LEAN B2) have been revised for the APPLIED VEHICLES listed above. When performing diagnosis for either of these DTCs, start by using the SERVICE PROCEDURE section of this bulletin. NOTE: The related Electronic Service Manuals (ESM) will be revised in the future to include these diagnostic steps.

NTB19-021

Service Bulletin/Repair Instructions

NISSAN; MIL ON WITH DTC P219A AND/OR P219B STORED This bulletin applies to Titan XD vehicles equipped with a VK56D gas engine only. SERVICE INFORMATION If the MIL is ON and DTC P219A (AIR FUEL RATIO IMBALANCE B1) and/or P219B (AIR FUEL RATIO IMBALANCE B2) is stored: - DO NOT replace the Air Fuel Ratio (A/F) sensor. - Refer to the applicable Electronic Service Manual (ESM) and follow the diagnostic procedure for DTC P219A and/or P219B.

NTB19-012

Service Bulletin/Repair Instructions

2017-2018 ROGUE SPORT; SURGE FEEL AT CONSTANT SPEED IF YOU CONFIRM Customer claims "surge feel? at a constant speed more than 25mph And The CONTROLLER ASSY IDM (CHASSIS CONTROL) part number is 476A0-6MA0A or 476A0-6MG0A. ACTION Reprogram the CONTROLLER ASSY IDM per the Service Procedure in this bulletin.

NTB16-028b

Service Bulletin/Repair Instructions

INTELLIGENT KEY BUTTONS INOPERATIVE BUT REQUEST SWITCHES WORK This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB16-110L

Service Bulletin/Repair Instructions

2013-2017 ALTIMA AND 2014-2017 ROGUE; 4 CYLINDER WITH DTC P17F0, P17F1, P0776, P2813, P1715, AND/OR P0841 STORED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB13-097g

Service Bulletin/Repair Instructions

ALL MODEL YEAR 2012 AND NEWER NISSAN VEHICLES; EVAP LEAK DTC P0442, P0455, P0456 INFORMATION This bulletin does NOT apply to LEAF vehicles and Titan XD vehicles with V8 diesel engine. This bulletin has been amended. See Amendment History on the last page. Please discard previous versions of this bulletin.

NTB15-049r

Service Bulletin/Repair Instructions

TELEMATICS SERVICE INFORMATION This bulletin applies only to vehicles equipped with a Telematics Communication Unit (TCU). This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB17-082b

Service Bulletin/Repair Instructions

NISSAN; DTC P0456 CAUSED BY EVAP LEAK AT VENT CONTROL VALVE O-RING This bulletin does NOT apply to LEAF vehicles and Titan XD vehicles with V8 diesel engine. This bulletin has been amended. See Amendment History on the last page. Please discard previous versions of this bulletin.

NTB19-009

Service Bulletin/Repair Instructions

2017-2019 ROGUE, ROGUE HYBRID AND ROGUE SPORT; CHASSIS CONTROL UNIT AND ADAS CONTROL UNIT 2 IDENTIFICATION SERVICE INFORMATION The CONTROLLER ASSY-IDM (Chassis Control Unit) and the CONTROLLER ASSYWARNING SPEAKER (ADAS Control Unit 2) may be incorrectly identified while diagnosing for related issues. The Chassis Control Unit and the ADAS Control Unit 2: - Cases, externally, appear identical. - Are located behind the glove box, in the same area. - Harness connectors are the same, and can be connected to the wrong component. NOTE: See Figure 1 for the correct locations of the Chassis Control Unit and the ADAS Control Unit 2. - Can be identified by their location (shown in Figure 1) and confirmed by the part number on the contorol unit?s label.

NPSB18-443 AEB U

Service Bulletin/Repair Instructions

2017-2018 Rogue and Rogue Sport Automatic Emergency Braking (AEB) Update Notification Letter Nissan is conducting an important Customer Service Initiative to increase awareness of an available update for the Automatic Emergency Braking (AEB) system on certain Model Year 2017-18 Rogue (T32), Rogue Sport (J11), and Rogue Hybrid (T32) vehicles. In rare instances and unique roadway environments such as certain types of railroad crossings and metal overpasses, the AEB system in some vehicles may activate braking when not needed. The driver can always override the AEB system by pressing the accelerator. To help enhance system performance for the customers that have experienced this issue, Nissan developed a special AEB system update that is available to owners at no cost for parts and labor during the duration of the Basic Coverage under their New Vehicle Limited Warranty (3 years/36,000 miles, whichever comes first). THIS CUSTOMER SERVICE INITIATIVE IS IMPLEMENTED TO MAKE CUSTOMERS AWARE OF AN AVAILABLE UPDATE. THIS INITIATIVE IS NOT A WARRANTY, AN EXTENSION OF THE NEW VEHICLE LIMITED WARRANTY, OR AN IMPLIED OR GENERAL WARRANTY, AND IS NOT CONNECTED TO ANY SALE OF THE VEHICLE.

NTB19-001

Service Bulletin/Repair Instructions

CHASSIS CONTROL MODULE DTC INFORMATION SERVICE INFORMATION If one or more of the following Chassis Control DTCs are stored: - C1BA0-00 ? (CHASSIS CONTROL BRAKE SYSTEM) - C1B92-00 ? (BRAKE CONTROL SYSTEM) - C1B93-00 ? (ENGINE/HEV SYSTEM) - C1B94-00 ? (TRANSMISSION SYSTEM) And One or more additional DTCs, other than those above, are also stored in a control unit other than the Chassis Control Module. - Perform the diagnostic/repair procedures for the additional DTCs of the other control unit FIRST. - Refer to the Electronic Service Manual (ESM) for DTC specific diagnostic information. Do not replace the CHASSIS CONTROL MODULE (CONTROLLER ASSY-IDM) if additional DTCs are present.

NTB18-084

Service Bulletin/Repair Instructions

2017-2018 ROGUE SPORT; REDUCED POWER DUE TO SNOW INGESTION IF YOU CONFIRM - An Applied Vehicle experiences reduced power during extremely heavy snow fall, And - Snow is found inside the air cleaner case. NOTE: The MIL may be ON with DTC P0101 (MAF SEN/CIRCUIT B1) stored. ACTION 1. Remove the front grille spacer. 2. Install foam blocks listed in the Parts Information. 3. Install the new front grille spacer.

NTB18-083

Service Bulletin/Repair Instructions

2014 - 2019 ROGUE; SQUEAK/CREAK NOISE FROM FRONT SUSPENSION BOUND BUMPER DRIVING OVER BUMPS IF YOU CONFIRM Using the flow chart on page 2, a squeak/creak noise is heard coming from the left or right front suspension bound bumper when driving over speed bumps or similar road surfaces. NOTE: This squeak/creak noise, if it should occur, is more noticeable in cold weather. ACTION Replace the front suspension bound bumper, only on the side that is making noise. - Refer to the appropriate Electronic Service Manual (ESM) for replacement information. SUSPENSION > FRONT SUSPENSION > REMOVAL AND INSTALLATION > FRONT COIL SPRING AND STRUT > Removal and Installation. - Pages 4 - 6 in this bulletin contain helpful information to perform this procedure. - Make sure to replace the one-time-use nuts listed in the PARTS INFORMATION. - Check the front wheel alignment; adjust to factory specifications as needed. NOTE: DO NOT apply lubricant to the bound bumper to resolve this issue.

NTB18-033a

Service Bulletin/Repair Instructions

2014 ? 2019 ROGUE; ACCELERATOR PEDAL VIBRATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB10-029e

Service Bulletin/Repair Instructions

NISSAN; VIBRATION AND/OR NOISE WHEN MAKING LOW SPEED TURNS This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB17-057b

Service Bulletin/Repair Instructions

2015-2019 ROGUE AND 2017-2019 ROGUE SPORT; DISTANCE TO EMPTY DOES NOT RESET This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB12-103f

Service Bulletin/Repair Instructions

CVT / TCM CALIBRATION DATA ?WRITE? PROCEDURE This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB18-077

Service Bulletin/Repair Instructions

MIL ON WITH DTC P0776, P1715 AND MAY HAVE HESITATION AND/OR LACK OF POWER This bulletin applies only to vehicles equipped with a CVT (Continuously Variable Transmission). IF YOU CONFIRM The MIL is ON with DTC P0776 (PC SOLENOID B ? Pressure Control Solenoid ?B? Performance/Stuck OFF) stored. NOTE: - If P0744, P0746, P0841, P0965, P2813, or P17F0 are stored this bulletin does not apply. Refer to ASIST for diagnostic assistance. - With this incident, if it should occur, P1715 (INPUT SPEED SENSOR) may be stored with DTC P0776. The vehicle may also hesitate and/or have reduced power. ACTION 1. Refer to the Repair Flow Chart on page 2 for mechanical CVT repair. 2. If needed, reprogram the TCM. - Refer to step 30 in the TCM Reprogram section (page 21) of the SERVICE PROCEDURE to confirm if reprogramming is needed. 3. Perform Additional Service (page 19).

NTB18-055a

Service Bulletin/Repair Instructions

CVT FLUID LEVEL QUICK CHECK GAUGE This bulletin applies only to vehicles equipped with a CVT (Continuously Variable Transmission). This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB15-077b

Service Bulletin/Repair Instructions

NISSAN; SIGNAL TECH-II INTELLIGENT KEY BATTERY TEST AND SIGNAL CHECK This bulletin has been amended. See Amendment History on the last page. Please discard previous versions of this bulletin.

NTB10-029d

Service Bulletin/Repair Instructions

NISSAN; VIBRATION AND/OR NOISE WHEN MAKING LOW SPEED TURNS This bulletin applies only to vehicles equipped with AWD (All-Wheel Drive) or 4WD (4-Wheel Drive). This bulletin has been amended. The APPLIED VEHICLES and PARTS INFORMATION sections have been revised. No other changes have been made. Please discard all previous versions of this bulletin.

NTB17-113a

Service Bulletin/Repair Instructions

2017-2018 ROGUE SPORT; WHEN COLD LONG CRANK TIME, ENGINE TURNS OFF, HESITATION, ROUGH IDLE, OR MISFIRE This bulletin has been amended. The Title and APPLIED VEHICLES have been revised. Part numbers have been added to Table A on page 5. No other changes have been made. Discard all previous versions of this bulletin.

PC652

Service Bulletin/Repair Instructions

Engine Coolant Voluntary Service Campaign ***** Campaign Summary***** Nissan is conducting a Voluntary Service Campaign to drain and refill the radiator on specific 2017 Nissan Pathfinder (R52) and Rogue (T32) vehicles. Due to an issue at the plant that has since been corrected, the radiator glycol/water coolant concentration mix ratio may be out of specification. Customers may notice poor heating performance as a result. ***** What Dealers Should Do ***** 1. Verify if vehicles are affected by this Voluntary Service Campaign using Service Comm I.D. PC652. 2. Dealers are requested to repair any affected vehicles in dealer new or pre-owned inventory to ensure customer satisfaction. 3. Dealers should use NTB18-066 to correct any vehicles subject to this campaign. 4. Once repaired, dealers should submit the claim, using the claims coding provided, and release the vehicle.

NTB18-066

Service Bulletin/Repair Instructions

VOLUNTARY SERVICE CAMPAIGN 2017 ROGUE AND PATHFINDER; ENGINE COOLANT INTRODUCTION Nissan is conducting this voluntary service campaign on certain specific model year 2017 Rogue and Pathfinder vehicles. The engine coolant in the radiator will be drained and refilled. This service will be performed at no charge to the customer for parts or labor. IDENTIFICATION NUMBER Nissan has assigned identification number PC652 to this campaign. This number must appear on all communication and documentation of any nature dealing with this campaign. DEALER RESPONSIBILITY Dealers are to repair vehicles falling within range of this campaign that enter the service department. This includes vehicles purchased from private parties, vehicles presented by transient (tourists) owners, and vehicles in a dealer?s inventory.

NTB17-040b

Service Bulletin/Repair Instructions

REVISED WHEEL ALIGNMENT SPECIFICATIONS This bulletin has been amended to add 2018-2019 Kicks. Please discard previous versions of this bulletin.

NTB15-049q

Service Bulletin/Repair Instructions

TELEMATICS SERVICE INFORMATION This bulletin applies only to vehicles equipped with a Telematics Communication Unit (TCU). This bulletin has been amended to add a Required Actions by Model and Year table on page 2, a Check OFF Sheet on page 21 and to reorganize the information throughout. It is necessary for you to read this revised procedure to properly perform this Service Information. Please discard previous versions of this bulletin.

NTB17-097a

Service Bulletin/Repair Instructions

2016-2018 ROGUE AND 2017-2018 ROGUE SPORT; WHISTLE NOISE TRANSMITTED TO CALL RECIPIENT WHEN USING BLUETOOTH HANDS-FREE PHONE SYSTEM This bulletin has been amended. Changes have been made throughout. It is necessary for you to read this revised procedure to properly perform this action. Please discard all previous versions of this bulletin.

NTB13-077d

Service Bulletin/Repair Instructions

CVT FLUID LEVEL CHECK SERVICE INFORMATION This bulletin applies only to vehicles equipped with a Continuously Variable Transmission (CVT). This bulletin has been amended. The APPLIED VEHICLES and SERVICE INFORMATION sections have been revised. No other changes have been made. Please discard all previous versions of this bulletin.

NTB15-049p

Service Bulletin/Repair Instructions

TELEMATICS SERVICE INFORMATION This bulletin only applies to vehicles equipped with a Telematics Communication Unit (TCU). This bulletin has been amended. Changes have been made to page 10 for 2018 Armada. Please discard previous versions of this bulletin.

NTB18-055

Service Bulletin/Repair Instructions

CVT FLUID LEVEL QUICK CHECK GAUGE This bulletin applies only to vehicles equipped with a Continuously Variable Transmission (CVT). SERVICE INFORMATION Special tool CVT8 Oil Level Quick Check Gauge (J-51155) is now available. Each dealer has been shipped one of these tools. Additional tools can be obtained from Tech?Mate at 1-800-662-2001. Refer to the SERVICE PROCEDURE on the next page to determine how to perform a CVT fluid quick level check.

NTB18-017b

Service Bulletin/Repair Instructions

NISSAN; SERVICE INFORMATION FOR DTCS B2EF0 AND B130C This bulletin only applies to vehicles equipped with a Telematics Communication Unit (TCU). This bulletin has been amended. APPLIED VEHICLES has been updated. On page 2, the procedural steps under DTC B130C have been revised. Discard all previous versions of this bulletin.

PC633 PM827 P832

Service Bulletin/Repair Instructions

CAMPAIGN BULLETIN Engine Control Module (ECM) Reprogram Regional (NV & AZ) Voluntary Service Campaign ***** Campaign Summary***** Nissan is conducting a Regional Voluntary Service Campaign to reprogram the Engine Control Module (ECM) on affected vehicles currently registered in Nevada and Arizona. The current programming may cause the air/fuel ratio to become excessively rich resulting in engine stop under certain high temperature and high altitude conditions. In addition, Nissan is asking dealers to inspect and, if necessary, replace the Positive Crankcase Ventilation (PCV) valve on certain 2013-14 Nissan Sentra vehicles. ***** What Dealers Should Do ***** 1. Verify if vehicles are affected by this Voluntary Service Campaign using Service Comm or DBS National Service History - Open Campaign I.D. Due to the various models involved and the associated responsible manufacturing location of origin, there are three (3) separate campaign IDs with unique Campaign Bulletins for each model: - PC633 - PM827 - P8325 New vehicles in dealer inventory can be also be identified using DCS (Sales-> Vehicle Inventory, and filter by Open Campaign). - Refer to NPSB 15-460 for additional information NOTE: These campaigns are state-specific and limited to vehicles that are currently registered, or previously registered, in the state of Nevada or Arizona only. 2. Nissan requests dealers repair any affected vehicles in retailer new or pre-owned inventory to ensure customer satisfaction. 3. Dealers should use the appropriate repair bulletin for the applicable model as listed below to correct any vehicles subject to this campaign. 4. Once repaired, dealer should submit a warranty claim and release the vehicle.

NTB18-041a

Service Bulletin/Repair Instructions

2017-2018 ROGUE, ROGUE HYBRID AND ROGUE SPORT; UNEXPECTED OPERATION OF AEB, FEB OR FCW This bulletin has been amended. Changes have been made throughout. It is necessary for you to read this revised procedure to properly perform this action. Please discard all previous versions of this bulletin.

NTB18-050

Service Bulletin/Repair Instructions

VOLUNTARY SERVICE CAMPAIGN 2014 ? 2017 ROGUE; ECM REPROGRAM INTRODUCTION Nissan is conducting this voluntary service campaign on certain specific model year 2014 ? 2017 Rogue vehicles that are currently registered in the states of Arizona or Nevada. The Engine Control Module (ECM) software will be reprogrammed. This service will be performed at no charge to the customer for parts or labor. IDENTIFICATION NUMBER Nissan has assigned identification number PC633 (VINs starting with 5N or JN) and P8325 (VINs starting with KN) to this campaign. This number must appear on all communication and documentation of any nature dealing with this campaign. DEALER RESPONSIBILITY Dealers are to repair vehicles falling within range of this campaign that enter the service department. This includes vehicles purchased from private parties, vehicles presented by transient (tourists) owners, and vehicles in a dealer?s inventory.

NTB13-054d

Service Bulletin/Repair Instructions

ALTIMA AND ROGUE; ENGINE TURNS OFF OR HESITATES WHEN ACCELERATING FROM A STOP DURING HOT AMBIENT TEMPERATURES (+100°F) This bulletin has been amended. Table A on page 5 has been revised. No other changes have been made. Please discard previous versions of this bulletin.

NTB18-031b

Service Bulletin/Repair Instructions

2016-2018 NISSAN CONNECT NAVIGATION SYSTEM SOFTWARE UPDATE TO RESOLVE SEVERAL ISSUES This bulletin has been amended. The IF YOU CONFIRM section and software number has changed. No other changes have been made. Please discard previous versions of this bulletin.

NTB18-031a

Service Bulletin/Repair Instructions

2016-2018 NISSAN CONNECT NAVIGATION SYSTEM SOFTWARE UPDATE TO RESOLVE SEVERAL ISSUES This bulletin applies only to vehicles equipped with navigation system. This bulletin has been amended to correct Bosch contact information on page 2. No other changes have been made. Please discard previous versions of this bulletin.

NTB13-054c

Service Bulletin/Repair Instructions

ALTIMA AND ROGUE; ENGINE TURNS OFF OR HESITATES WHEN ACCELERATING FROM A STOP DURING HOT AMBIENT TEMPERATURES (+100°F) This bulletin has been amended. Table A on page 6 has been revised. No other changes have been made. Please discard previous versions of this bulletin.

NTB18-031

Service Bulletin/Repair Instructions

2016-2018 NISSAN CONNECT NAVIGATION SYSTEM SOFTWARE UPDATE TO RESOLVE SEVERAL ISSUES This bulletin applies only to vehicles equipped with navigation system. IF YOU CONFIRM One or more of the following is occurring: - The navigation unit intermittently reboots: - At random or while listening to SXM or on a Bluetooth hands-free phone call. - Loud booming noise from speakers while on a Bluetooth hands-free call. - Navigation unit screen illumination does not change at night as designed. - AM/FM signal strength issues. - A status message ?Voice Recognition is initializing, please wait? is displayed when pressing the voice recognition button 2-3 minutes after the ignition is first turned ON. NOTE: If the message is displayed within the first 2-3 minutes this is normal. The voice recognition is loading phonebook contacts into its system. AND - The Software version has been confirmed as ?needs update? (refer to page 4). ACTION - Perform the SERVICE PROCEDURE starting on page 3 and reprogram the Navigation system with USB memory stick shown below.

NTB03-074m

Service Bulletin/Repair Instructions

FOG LAMP AND/OR HEADLAMP FOGGING This bulletin has been amended to add Fog Lamps and modify one step in the flow chart on page 3. No other changes have been made. Please discard previous versions of this bulletin.

NTB16-115a

Service Bulletin/Repair Instructions

REVISED WHEEL ALIGNMENT SPECIFICATIONS This bulletin has been amended. The APPLIED VEHICLES were updated with new models and model years. No other changes have been made. Discard all previous versions of this bulletin.

NTB18-009a

Service Bulletin/Repair Instructions

2017 ? 2018 ROGUE SPORT; FRONT WHEEL ALIGNMENT TOTAL TOE SPECIFICATION This bulletin has been superseded to NTB16-115. Discard previous versions of this bulletin.

NTB18-033

Service Bulletin/Repair Instructions

2014 - 2018 ROGUE; ACCELERATOR PEDAL VIBRATION IF YOU CONFIRM A vibration from the accelerator pedal between 1600 - 2000 RPM. ACTION Install the new brake booster vacuum tube and hose listed in the PARTS INFORMATION section of this bulletin.

NTB16-018c

Service Bulletin/Repair Instructions

MIL ON WITH P0603 STORED FOR ECM BACK UP CIRCUIT This bulletin does NOT apply to Titan equipped with Cummins V8 Diesel engine. This bulletin has been amended to add a NOTE in the Applied Vehicles. No other changes have been made. Please discard previous versions of this bulletin.

NTB17-084a

Service Bulletin/Repair Instructions

2014-2017 ROGUE AND ROGUE HYBRID; SQUEAK OR RATTLE FROM FRONT DOOR FINISHER This bulletin has been amended. The PARTS INFORMATION and CLAIMS INFORMATION sections have changed. No other changes have been made. Please discard all previous versions of this bulletin.

NTB13-107b

Service Bulletin/Repair Instructions

INTELLIGENT KEY NOT DETECTED / ENGINE WILL NOT START This bulletin has been amended to update the Applied Vehicles. No other changes were made. Please discard previous versions of this bulletin.

NTB18-017a

Service Bulletin/Repair Instructions

NISSAN; SERVICE INFORMATION FOR DTCS B2EF0 AND B130C This bulletin applies only to vehicles equipped with Telematics. This bulletin has been amended. APPLIED VEHICLES was updated and a DTC listed in the SERVICE INFORMATION was corrected. No other changes have been made. Discard all previous versions of this bulletin.

NTB11-044c

Service Bulletin/Repair Instructions

WHEEL BALANCING SERVICE INFORMATION This bulletin has been amended. The publication date has been revised to include the latest models and model years. No other changes have been made. Please discard previous versions of this bulletin.

NTB18-019

Service Bulletin/Repair Instructions

2013-2018 ALTIMA AND 2014-2018 ROGUE; ENGINE SUPPORT TOOLS SERVICE INFORMATION A new Engine Support Tool and Engine Support Bracket are now available to allow the CVT to be removed from the Applied Vehicles without having to remove the engine. The procedures in this bulletin are different than those that are currently in the Electronic Service Manual (ESM), which will be updated with this information at a later date. Please refer to the vehicle specific service procedure to use these new tools: Altima Page 2 Rogue AWD Page 11 Rogue FWD Page 24

PC601 2016-18

Service Bulletin/Repair Instructions

Left Hand Engine Mounting Insulator Voluntary Service Campaign UPDATE March 2, 2018 Please discard earlier versions of this bulletin The announcement from January 18, 2018 has been revised to include: - Retailed vehicles affected by this campaign are now include in this announcement - Campaign repair bulletin, NTB18-002 has been revised to include the location of a repair video, which is now available in Virtual Academy under the Tech Training Garage Videos tab. See video #554: ?2016-17 Rogue Left Hand Engine Mount Insulator Campaign?. - Nissan has developed a parts shipment plan for use on retailed units. Parts (2 per dealer) will begin to arrive at dealerships on Monday, March 5, 2018. o Dealers may order parts via normal ordering process beginning March 12, 2018, if additional parts are needed.

NTB18-002a

Service Bulletin/Repair Instructions

VOLUNTARY SERVICE CAMPAIGN 2016-2017 ROGUE; LEFT HAND ENGINE MOUNTING INSULATOR This bulletin has been amended. A note with the video link was added to page 2. No other changes have been made. Please discard all previous versions of this bulletin.

NTB18-017

Service Bulletin/Repair Instructions

NISSAN; SERVICE INFORMATION FOR DTCS B2EF0 AND B130C This bulletin applies only to vehicles equipped with Telematics. SERVICE INFORMATION Diagnostic information in the Electronic Service Manuals (ESM) for the following DTCs may be missing or incorrect: -B2EF0 ? INTERNAL BATTERY (CIRC VOLT BELOW THRESHOLD) -B130C ? TCU (Telematics Control Unit) PAIRING ERROR If one of these DTCs is stored, follow the steps listed below along with the Electronic Service Manual (ESM) to compete the required repairs. DTC B2FE0 ? INTERNAL BATTERY (CIRC VOLT BELOW THRESHOLD): 1. Start the engine and let it idle for 30 minutes (to allow charging of the TCU internal battery). -2018 LEAF only: Put the vehicle in Ready to Drive mode (depress the brake pedal and depress the power [?ignition?] switch) for 30 minutes. 2. Verify the DTC can be erased. 3. If the DTC will not erase, replace the TCU. DTC B130C: 1. Collect all keys, and then re-register them to the vehicle. 2. Verify the DTC can be erased. 3. If the DTC will not erase, replace the TCU. NOTE: The related Electronic Service Manuals (ESM) will be updated at a later date. CLAIMS INFORMATION Refer to the current Nissan Warranty Flat Rate Manual and submit a claim for the repairs performed.

NTB15-049o

Service Bulletin/Repair Instructions

TELEMATICS SERVICE INFORMATION This bulletin applies only to vehicles equipped with a Telematics Communication Unit (TCU). This bulletin has been amended. Changes have been made throughout. It is necessary to read the revised procedure(s) in entirety to properly perform the action(s). Please discard previous versions of this bulletin.

NTB18-009

Service Bulletin/Repair Instructions

2017 ? 2018 ROGUE SPORT; FRONT WHEEL ALIGNMENT TOTAL TOE SPECIFICATION SERVICE INFORMATION Hunter brand alignment machines may have incorrect alignment specifications for ?total toe-in? on 2017-2018 Rogue Sport. - The correct specifications can be found in the Electronic Service Manual (ESM) SUSPENSION > FRONT SUSPENSION (see page 2). - Revised data is currently available for installation from Hunter. - Until the updated data is installed in your Hunter machine, please use the correct specifications on page 2, or in the Electronic Service Manual (ESM).

NTB18-008

Service Bulletin/Repair Instructions

ADAS SYSTEM DTC C1A03, C1A04, AND/OR C1B01 SERVICE INFORMATION This bulletin applies only to vehicles equipped with Automatic Emergency Braking (AEB) or Forward Emergency Braking (FEB). SERVICE INFORMATION If the following ICC/ADAS codes are stored, make sure to follow the diagnostic procedures in the Electronic Service Manual (ESM) before replacing any parts. C1A03 ? VEHICLE SPEED SENSOR -The diagnostic procedure in the ESM includes check and, if needed, repair for ABS DTCs before replacing ADAS components. -If repairs are performed for the ABS system; when compete, perform DTC Confirmation Procedure again before doing any additional repairs. C1A04 ? ABS/TCS/VDC SYSTEM -The diagnostic procedure in the ESM includes check and, if needed, repair for ABS DTCs before replacing ADAS components. -If repairs are performed for the ABS system; when compete, perform DTC Confirmation Procedure again before doing any additional repairs. C1B01 CAM AIMING INCMP -The diagnostic procedure in the ESM includes check and, if needed, repair for LANE CAMERA DTCs before replacing ADAS components. -LANE CAMERA DTC may require adjustment of the lane camera. -If repairs/adjustments are performed for the Lane Camera; when compete, perform DTC Confirmation Procedure again before doing any additional repairs.

NTB17-083a

Service Bulletin/Repair Instructions

MOTION ACTIVATED LIFTGATE STICKER This bulletin applies to vehicles equipped with a Motion Activated Liftgate. This bulletin has been amended to add 2018 Murano, update model years in the Applied Vehicles, and change the part number in the Parts Information. Please discard previous version of this bulletin.

NTB18-002

Service Bulletin/Repair Instructions

VOLUNTARY SERVICE CAMPAIGN 2016-2017 ROGUE; LEFT HAND ENGINE MOUNTING INSULATOR INTRODUCTION Nissan is conducting this Voluntary Service Campaign on certain specific model year 2016 and 2017 Rogue vehicles. This service will be performed at no charge to the customer for parts or labor. IDENTIFICATION NUMBER Nissan has assigned identification number PC601 to this campaign. This number must appear on all communication and documentation of any nature dealing with this campaign. DEALER RESPONSIBILITY It is the dealer?s responsibility to check Service COMM or Dealer Business Systems (DBS) National Service History for the campaign status on each vehicle falling within the range of this voluntary safety recall which for any reason enters the service department. This includes vehicles purchased from private parties or presented by transient (tourist) owners and vehicles in a dealer?s inventory. Federal law requires that new vehicles in dealer inventory which are the subject of a safety recall must be corrected prior to sale. Failure to do so can result in civil penalties by the National Highway Traffic Safety Administration. While federal law applies only to new vehicles, Nissan strongly encourages dealers to correct any used vehicles in their inventory before they are retailed.

NTB13-054b

Service Bulletin/Repair Instructions

ALTIMA AND ROGUE; ENGINE TURNS OFF OR HESITATES WHEN ACCELERATING FROM A STOP DURING HOT AMBIENT TEMPERATURES (+100°F) This bulletin has been amended. The APPLIED VEHICLES section and Table A on pages 5 and 6 have been revised. No other changes have been made. Please discard previous versions of this bulletin.

NTB15-049n

Service Bulletin/Repair Instructions

TELEMATICS SERVICE INFORMATION This bulletin applies to vehicles equipped with a TCU (Telematics Communication Unit). This bulletin has been amended. A correction was made to the Service Procedure on page 23. No other changes were made. Please discard previous versions of this bulletin.

PC593 2017

Service Bulletin/Repair Instructions

Key Fob Voluntary Service Campaign This bulletin applies to vehicles with trim levels of SV and SL only. Nissan is conducting a Voluntary Service Campaign on approximately 50,944 model year 2017 Nissan Rogue SV and SL trim level vehicles. Nissan has discovered that the I-Key fob may be missing the FCC ID label required by the Federal Communications Commission. To correct this condition, Nissan is conducting a Voluntary Service Campaign to provide customers with two FCC ID labels (included with the owner letter) that can be easily affixed to each I-Key fob for your 2017 Rogue. ***** What Dealers Should Do ***** 1. No dealer action is necessary for this Voluntary Service Campaign. 2. If a customer has a notification letter, but has lost or damaged the two (2) FCC ID labels, replacement labels can be acquired by sending an email to nnafqasupport@nissan-usa.com - Dealers should specify: - PC593 ? I-Key Fob Labels Required (in title of email) - Customer VIN - I-Key fob part number - Name and address to send the new labels to NOTE: SERVICE COMM will not be active for this campaign.

NTB17-057a

Service Bulletin/Repair Instructions

2015-2017 ROGUE AND 2017-2018 ROGUE SPORT; DISTANCE TO EMPTY DOES NOT RESET This bulletin has been amended. Changes have been made throughout. Please discard all previous versions of this bulletin.

NTB17-118

Service Bulletin/Repair Instructions

NISSAN; INTELLIGENT KEY IDENTIFICATION AND REGISTRATION TIPS This bulletin applies to vehicles equipped with Intelligent Key only. SERVICE INFORMATION When replacing or adding an Intelligent Key, it is very important to make sure the correct Intelligent Key is selected from the parts department. - A running change was made that will help identify the correct Intelligent Key. - Beginning in late 2017 and early 2018 the last five digits of the Intelligent Key part number is marked on the Intelligent Key under the mechanical key. - See page 2 for location images of this part number addition. NOTE: - A correct Intelligent Key may or may not have the last five digits of the part number as shown on page 2. - The above running change was applied as a ?help? to identify the correct Intelligent Key for a given vehicle, but the actual part number listed in the parts catalog did not change. - Make sure to use the electronic parts catalog (FAST) or equivalent to confirm the correct Intelligent Key for a given vehicle.

NTB17-040a

Service Bulletin/Repair Instructions

REVISED WHEEL ALIGNMENT SPECIFICATIONS This bulletin has been amended to add 2018 Versa Sedan and 2018 Versa Note. No other changes have been made. Please discard previous versions of this bulletin.

NTB15-049m

Service Bulletin/Repair Instructions

TELEMATICS SERVICE INFORMATION This bulletin applies to vehicles that are equipped with a wireless communication device called a Telematics Communication Unit (TCU). This bulletin has been amended. Changes have been made throughout. You must read the entire bulletin to understand all the changed information. Please discard previous versions of this bulletin.

NTB17-113

Service Bulletin/Repair Instructions

2017 ROGUE SPORT; WHEN COLD LONG CRANK TIME, ENGINE TURNS OFF, HESITATION, ROUGE IDLE, OR MISFIRE IF YOU CONFIRM After the engine has been OFF for more than 2 hours, any of the following occur during engine start and warm up: - Long engine crank time (with mechanical key only) - Engine turns OFF, requiring a restart - Hesitation on acceleration - Rough Idle - Engine misfire ACTION 1. Refer to step 6 in the SERVICE PROCEDURE to confirm this bulletin applies to the vehicle you are working on. 2. If this bulletin applies, reprogram the ECM.

NTB15-049L

Service Bulletin/Repair Instructions

TELEMATICS SERVICE INFORMATION This bulletin applies to vehicles equipped with a Telematics Communication Unit (TCU). This bulletin has been amended. Information for several 2018 models has been added. No other changes have been made. Please discard previous versions of this bulletin.

NTB11-044b

Service Bulletin/Repair Instructions

WHEEL BALANCING SERVICE INFORMATION This bulletin has been amended. The publication date has been revised to include the latest models and model years. No other changes have been made. Please discard previous versions of this bulletin.

NTB15-049k

Service Bulletin/Repair Instructions

TELEMATICS SERVICE INFORMATION This bulletin has been amended. The Applied Vehicles section has been revised and TCU Configuration section has been added. No other changes have been made. Please discard previous versions of this bulletin.

NTB13-077c

Service Bulletin/Repair Instructions

CVT FLUID LEVEL CHECK SERVICE INFORMATION This bulletin applies only to vehicles equipped with a Continuously Variable Transmission (CVT). This bulletin has been amended. The APPLIED VEHICLES section has been revised. No other changes have been made. Please discard all previous versions of this bulletin.

NTB17-082a

Service Bulletin/Repair Instructions

NISSAN; DTC P0456 CAUSED BY EVAP LEAK AT VENT CONTROL VALVE O-RING This bulletin has been amended. The APPLIED VEHICLES and CLAIMS INFORMATION sections have been revised. No other changes have been made. Please discard previous versions of this bulletin.

NTB17-091

Service Bulletin/Repair Instructions

2013-2017 ALTIMA AND 2014-2017 ROGUE; MIL ON WITH DTC P2004 STORED IF YOU CONFIRM MIL is ON with P2004 (INTAKE MANIFOLD RUNNER CONTROL VALVE POSITION SENSOR) stored. And There are no drivability issues. ACTION 1. Remove the intake manifold. 2. Replace the intake manifold runner control valve position sensor. 3. Re-install intake manifold.

NTB15-045e

Service Bulletin/Repair Instructions

2014-2017 ROGUE; MANUAL HVAC IMPROPER OPERATION This bulletin has been amended. Changes have been made on pages 1 and 2. No other changes have been made. Please discard all previous versions.

NTB17-083

Service Bulletin/Repair Instructions

MOTION ACTIVATED LIFTGATE STICKER This bulletin applies only to Pathfinder SL or Platinum, Rogue SL, and Rogue Hybrid SL vehicles. SERVICE INFORMATION Applied vehicles equipped from the factory with a Motion Activated Liftgate should also have a Motion Activated Liftgate Sticker applied to the back door window glass. DO NOT remove this sticker during PDI, or when the vehicle is washed, or any other time the vehicle is in inventory. NOTE: - Motion activated liftgate sticker is only to be removed by the customer. - Replacement stickers can be obtained from your parts department.

NTB17-084

Service Bulletin/Repair Instructions

2014-2017 ROGUE AND ROGUE HYBRID; SQUEAK OR RATTLE FROM FRONT DOOR FINISHER IF YOU CONFIRM While driving, a squeak noise is heard from either front door finisher in the areas shown in Figure 1, and The noise stops when the area is pressed, and The VIN begins with 5N1. or The VIN begins with KNM and was built before KNMAT2M(**)GP 605885 // October 1, 2015. AND/OR A rattle noise is heard when either front door outside handle is operated, and The VIN begins with 5N1 and was built before 5N1AT2M(**)HC 830035 // May 1, 2017. ACTION - If applicable, apply felt tape to repair front door finisher squeak noise. See page 2. - If applicable, apply felt tape to repair front door handle noise. See page 4.

NTB17-079

Service Bulletin/Repair Instructions

2017 ROGUE SPORT; MIL ON WITH DTC P050B STORED IF YOU CONFIRM - The MIL is ON with P050B stored. And - No other drivability issues are present. ACTION 1. Refer to step 6 in the SERVICE PROCEDURE to confirm this bulletin applies to the vehicle you are working on. 2. If this bulletin applies, reprogram the ECM.

NTB15-026c

Service Bulletin/Repair Instructions

2014-2017 ROGUE; LACKS POWER DUE TO SNOW INGESTION This bulletin has been amended. Changes have been made on pages 1 ? 5 and in the Parts Information. Please discard previous versions of this bulletin.

NTB17-073

Service Bulletin/Repair Instructions

2017 ROGUE; PARK LIGHT ON SHIFT ASSEMBLY REMAINS ON LONGER THAN 5 MINUTES AFTER SHIFTED TO PARK This bulletin applies to vehicles without Intelligent Key. IF YOU CONFIRM After the vehicle has been shifted into Park (P), the ignition switch is OFF and the doors are closed: - P indicator light (Figure 1) on the shift assembly does not go OFF after 5 minutes. And - Applied VIN begins with ?JN8?. ACTION - Adjust the key interlock cable. NOTE: Nissan vehicle warranty does not cover incidents due to lack of vehicle maintenance and/or physical damage. Refer to New Vehicle Limited Warranty in the Nissan Assurance Products Resource Manual (APRM) for warranty coverage guidelines and complete information regarding warranty coverage.

P7326

Service Bulletin/Repair Instructions

Vehicle Information Display Dealer Inventory *****Dealer Announcement***** Nissan is conducting a dealer inventory quality action to reprogram the vehicle information display on 2,496 specific 2017 Rogue Sport vehicles identified in Service Comm. These vehicles are either currently in dealer inventory or assigned and in transit to the dealer.

NTB12-055f

Service Bulletin/Repair Instructions

CLICKING NOISE FROM FRONT OR REAR AXLE DURING TAKE-OFF/ACCELERATION This bulletin has been amended. The APPLIED VEHICLES section has been revised. No other changes have been made. Please discard previous versions of this bulletin.

NTB12-103e

Service Bulletin/Repair Instructions

CVT / TCM CALIBRATION DATA "WRITE" PROCEDURE This bulletin does not apply to Pathfinder Hybrid, Murano Hybrid or Rogue Hybrid This bulletin has been amended. APPLIED VEHICLES has been updated. SERVICE INFORMATION has been amended. A REPAIR TABLE has been added. Procedural steps have been added to SERVICE PROCEDURE. Discard all previous versions of this bulletin.

NTB15-013d

Service Bulletin/Repair Instructions

NISSAN; PROCEDURE TO CLEAN CVT TRANSMISSION FLUID COOLERS This bulletin has been amended. The APPLIED VEHICLES section has been revised. No other changes have been made. Please discard previous versions of this bulletin.

NTB17-043

Service Bulletin/Repair Instructions

2017 ROGUE; DRIVER AIR BAG MODULE REMOVAL SERVICE INFORMATION Use the Service Procedure in this bulletin when removing the Driver Air Bag Module. As of the date of this bulletin, the procedure in this bulletin is different from the one in the Electronic Service Manual (ESM). The ESM will be updated at a later date.

NTB17-040

Service Bulletin/Repair Instructions

REVISED WHEEL ALIGNMENT SPECIFICATIONS SERVICE INFORMATION For the Applied Vehicles, some wheel alignment specifications listed in the Front Suspension (FSU) and Rear Suspension (RSU) sections of the Electronic Service Manual (ESM) have been revised. Updated ESMs will be distributed to the field as quickly as possible. Until the updated ESMs are made available, please use the corrected specifications listed in this bulletin.

NTB17-028

Service Bulletin/Repair Instructions

2014-2017 ROGUE; BLOWER MOTOR SERVICE INFORMATION SERVICE INFORMATION When diagnosing the operation of the heating and cooling system's blower motor, make sure there is no interference from other personal devices before replacing any parts or performing any repairs. All personal devices (12V charger, USB charger, PC charger, etc.) must be unplugged/removed from the vehicle when diagnosing/verifying the customer issue related to blower motor operation.

NTB17-022

Service Bulletin/Repair Instructions

2014-2017 ROGUE; ENGINE AIR CLEANER CASE DUCT SERVICE INFORMATION SERVICE INFORMATION When removing and installing the engine air cleaner case duct (case duct) in an APPLIED VEHICLE for any reason, use the information in this bulletin in addition to the procedure in the EM-Engine Mechanical section of the Electronic Service Manual (ESM).

REVISION 1 - PC5

Service Bulletin/Repair Instructions

Tire Pressure Monitoring Sensors (TPMS) Initialization The announcement from January 21, 2017 has been revised to include: o Configuration step is not necessary and has been removed from the attached procedure. Please discard earlier versions of this bulletin.

NTB14-068b

Service Bulletin/Repair Instructions

POWER MOONROOF INITIALIZATION SERVICE INFORMATION This bulletin has been amended. The APPPLIED VEHICES section and step 3 on page 3 have been revised. No other changes have been made. Please discard all previous versions.

NTB17-009

Service Bulletin/Repair Instructions

2017 ROGUE; ALUMINUM WHEEL CENTER CAP SERVICE INFORMATION SERVICE INFORMATION Some 2017 Rogue vehicles come equipped with optional factory silver colored aluminum wheels. The center caps for the wheels of these vehicles are black in color with chrome emblem (see Figure 1 and 2). This is the correct combination of wheel and center cap for these vehicles. DO NOT file a Warranty Claim to change the center caps for these vehicles.

PC543 2017 Rogue

Service Bulletin/Repair Instructions

Tire Pressure Monitoring Sensors (TPMS) Initialization ***** Detailed Information ***** Nissan is conducting a dealer inventory service action to initialize the Tire Pressure Monitoring Sensors (TPMS) on approximately 745 specific MY2017 Rogue (T32) vehicles. No parts are required for this action. ***** What Dealers Should Do ***** 1. Verify if vehicles currently in dealer inventory are affected by this inventory service action using Service Comm I.D. PC543. - New vehicles in dealer inventory can be also be identified using DCS (Sales-> Vehicle Inventory, and filter by Open Campaign). - Refer to NPSB 15-460 for additional information 2. Use the attached Electronic Service Manual (ESM) procedure to initialize the TPMS. Note: Dealers should continue to check new arriving inventory for applicability. 3. Dealers are requested to remedy any affected vehicle in dealer new or pre-owned inventory to ensure customer satisfaction.

LAUNCH PC543 - 2

Service Bulletin/Repair Instructions

LAUNCH PC543 - 2017 Rogue TPMS Initialization - SA - Dealer Announcement and ESM Procedure Detailed Information: Nissan is conducting a dealer inventory service action to initialize the Tire Pressure Monitoring Sensors (TPMS) on approximately 745 specific MY2017 Rogue (T32) vehicles. No parts are required for this action. What Dealers Should Do: 1. Verify if vehicles currently in dealer inventory are affected by this inventory service action using Service Comm I.D. PC543. ? New vehicles in dealer inventory can be also be identified using DCS (Sales-> Vehicle Inventory, and filter by Open Campaign). Refer to NPSB 15-460 for additional information 2. Use the attached Electronic Service Manual (ESM) procedure to initialize the TPMS. Note: Dealers should continue to check new arriving inventory for applicability. 3. Dealers are requested to remedy any affected vehicle in dealer new or pre-owned inventory to ensure customer satisfaction.

NTB17-003

Service Bulletin/Repair Instructions

PATHFINDER, MURANO, AND ROGUE; FLUID LEAK CAUSED BY TRANSFER ASSEMBLY RIGHT SIDE DRIVE SHAFT SEAL This bulletin applies only to AWD equipped vehicles. IF YOU CONFIRM Fluid is leaking from the right side of the transfer assembly (see Figure 1). NOTE: The fluid leak is not caused by the seal shown in Figure 1. ACTION 1. DO NOT REPLACE the transfer assembly. 2. Reseal the transfer assembly. - Refer to the Electronic Service Manual (ESM), section DLN ? Driveline, for transfer assembly removal, reseal, and installation information. - Refer to page 2 and 3 for additional information. CAUTION: Be careful not to damage the transfer assembly right side drive shaft seal when reinstalling the drive shaft.

NTB12-110c

Service Bulletin/Repair Instructions

POWER BACK DOOR CALIBRATION This bulletin has been amended. Step 15 has been revised. No other changes have been made. Please discard previous versions of this bulletin.

NTB12-110b

Service Bulletin/Repair Instructions

POWER BACK DOOR CALIBRATION The Applied Vehicles in this bulletin have been amended. No other changes have been made Please discard previous versions of this bulletin.

NTB14-059b

Service Bulletin/Repair Instructions

2011-2017 LEAF; REPLACEMENT HIGH VOLTAGE BATTERY PACK This bulletin has been amended. The Applied Vehicles and Parts Information have been revised. No other changes have been made. Please discard previous versions of this bulletin.

NTB15-048a

Service Bulletin/Repair Instructions

2014-2017 ROGUE; VIBRATION IN STEERING WHEEL OR PASSENGER FRONT SEAT AT IDLE This bulletin has been amended to add model years and to remove any reference to the A/C. Please discard previous versions of this bulletin.

NTB16-123

Service Bulletin/Repair Instructions

PLASTIC INTERIOR TRIM PROTECTIVE COVERING REMOVAL SERVICE INFORMATION Vehicles are delivered with plastic interior trim protective covering on the front and rear seats, front and rear door panel finishers, steering wheel, and sun visors (see examples on page 2). When removing the protective covering, care must be used to avoid scuffs, scrapes, cuts, and other abrasive contact to interior trim components. DO NOT use sharp objects like razor blades, box cutters, knives, etc. when removing the plastic interior trim protective covering. IMPORTANT All soft trim described in this bulletin is on automatic return to NNA. Any trim found damaged in the way described in this bulletin will be charged back to the dealer.

NTB13-107a

Service Bulletin/Repair Instructions

INTELLIGENT KEY NOT DETECTED / ENGINE WILL NOT START This bulletin has been amended to update the Applied Vehicles and make changes to the body of the bulletin. Please discard previous versions.

NTB16-116

Service Bulletin/Repair Instructions

NISSAN; DIAGNOSIS INFORMATION FOR ABS DTC C1130 SERVICE INFORMATION When diagnosing for DTC C1130 (ENGINE SIGNAL): ECM related DTCs (P-codes) must be diagnosed, repaired, and DTCs erased first. - DTC C1130 is an ABS DTC that indicates an output signal of the ECM is not recognized. - Absent or incorrect ECM signals, that are indicated by corresponding P-codes, may trigger C1130 in the ABS control unit. - Some vehicle features that can be affected by absent or incorrect ECM signals are: - Forward Emergency Braking (FEB) - Intelligent Cruise Control (ICC) - VDC/ABS/TCS

PC499A

Service Bulletin/Repair Instructions

Nissan has updated the previously announced Dealer Quality Hold (released October 18,2016) to a New Dealer Inventory Service Action. Dealers are asked to update the front camera software on 16 specific 2017 Rogue (T32) vehicles identified in Service Comm.

NTB15-045d

Service Bulletin/Repair Instructions

2014-2017 ROGUE; MANUAL HVAC IMPROPER OPERATION This bulletin has been amended. Changes have been made throughout. Please discard all previous versions.

NTB15-049j

Service Bulletin/Repair Instructions

TELEMATICS SERVICE INFORMATION This bulletin has been amended. Information for 2017 Rogue and Rogue Hybrid has been applied. No other changes have been made. Please discard previous versions of this bulletin.

PC499 - 2017 Rog

Service Bulletin/Repair Instructions

Front Camera - Quality Assurance Hold ***** Detailed Information ***** Nissan is committed to a high level of customer service and satisfaction. This commitment requires Nissan to periodically place certain specific vehicles on a temporary Quality Assurance (QA) Hold to assure that these vehicles, as delivered to our customers, meet our exacting standards and our customers' expectations. Effective immediately, Nissan is placing a temporary Quality Assurance (QA) Hold on approximately 17 specific MY2017 Rogue (T32) vehicles. ***** What Dealers Should Do ***** 1. Verify if vehicles currently in dealer inventory are affected by this QA Hold using Service Comm I.D. PC499 Note: Dealers should continue to check new arriving inventory for QA Hold applicability. 2. Please do not drive, sell, or trade the specific 2017 Rogue vehicles in Dealer Inventory subject to this QA Hold. 3. No further action is necessary at this time. Nissan will provide an update by October 31st, 2016.

NTB13-097D

Service Bulletin/Repair Instructions

ALL MODEL YEAR 2012 AND NEWER NISSAN VEHICLES; EVAP LEAK DTC P0442, P0455, P0456 INFORMATION THIS BULLETIN HAS BEEN AMENDED. THE TITLE HAS BEEN REVISED, AND THE BULLETIN NOW INCLUDES VEHICLES IN PRODUCTION AS OF THE DATE OF THIS UPDATE. NO OTHER CHANGES HAVE BEEN MADE. PLEASE DISCARD ALL PREVIOUS VERSIONS OF THIS BULLETIN.

NTB15043

Service Bulletin/Repair Instructions

SERVICE INFORMATION The appearance of painted alloy wheels can be damaged if acidic cleaners are used. DO NOT use Chrome Wheel Cleaner on Painted Wheels. Many chrome wheel cleaners have acidic ingredients. Make sure to follow all instruction in the Appearance and Care Section of the Owner?s Manual. Damage to wheel appearance due to the use of inappropriate chemicals or cleaning products is not covered under warranty. See this bulletin for further detail.

NTB14032

Service Bulletin/Repair Instructions

SERVICE INFORMATION Warranty claims coding for repairing wiring harnesses for all Nissan vehicles has changed. This bulletin gives an outline of the technician?s responsibilities in assisting the dealer?s claims administrator to properly code a harness repair. Failure to provide correct information may result in claims suspension or rejection. See this bulletin for further detail.

Reading this report

Complaint counts are reports filed with NHTSA, not failure rates. A common model collects more of them than a rare one that breaks more often.