Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
NTB09-131C
Service Bulletin/Repair Instructions
CERTIFICATION LABEL AND VIN PLATE REPLACEMENT SERVICE INFORMATION Because of collision damage or other vehicle repair, a replacement “Certification Label” or “VIN Plate/Label” may be needed. HINT: Certification Label = FMVSS (Federal Motor Vehicle Safety Standards) label. These items may be available from Nissan by request if certain criteria are met. This bulletin lists the criteria and provides an application form for such replacements. · The “VIN Plate/Label” (metal plate or vinyl label) is attached to the instrument panel or body on the driver side at the base of the windshield (see Figure 1). · The “Certification Label” (vinyl adhesive label) is located on the lower area of the driver side B-Pillar (see Figure 1).
NTB15-049CC
Service Bulletin/Repair Instructions
TELEMATICS SERVICE INFORMATION HINT: This bulletin applies to vehicles equipped with a 4G network compatible TCU. TCUs compatible with 3G network only are no longer supported. SERVICE INFORMATION The APPLIED VEHICLES that come equipped with a factory installed SOS switch, located near the overhead map lamp, also come equipped with a wireless communication device called a Telematics Communication Unit (TCU). With an active NissanConnect® Services subscription, the TCU communicates with the NissanConnect® Services Data Center to provide various security and convenience services. This bulletin contains important service procedures that must be performed properly in order to set-up and maintain the telematics system for the APPLIED VEHICLES. · A table has been provided on the next page that lists the steps required to successfully configure a TCU after it has been replaced. · A CHECK-OFF SHEET has been provided on page 20 to print and check off steps as they are performed. Staple the completed CHECK-OFF SHEET to the repair order.
NTB19-033G
Service Bulletin/Repair Instructions
INTELLIGENT CRUISE CONTROL INOPERATIVE AND AEB/FEB WARNING LIGHT ON OR RADAR OBSTRUCTION MESSAGE DISPLAYED WITH DTC C1A16 OR C2582 IF YOU CONFIRM IMPORTANT: The purpose of ACTION (on the next page) is to give you a quick idea of the work you will be performing. You MUST closely follow the entire SERVICE PROCEDURE as it contains information that is essential to successfully completing this repair. Nissan Bulletins are intended for use by qualified technicians, not 'do-it-yourselfers'. Qualified technicians are properly trained individuals who have the equipment, tools, safety instruction, and know-how to do a job properly and safely. NOTE: If you believe that a described condition may apply to a particular vehicle, DO NOT assume that it does. See your Nissan dealer to determine if this applies to your vehicle. The customer states that the ICC stopped working while driving, OR The customer states that the AEB/FEB warning light is ON, or turned ON, while driving (Figure 1), OR The message “Unavailable Front Radar Obstruction” or “Forward Driving Aids Temporarily Disabled Front Sensor Blocked See Owner's Manual” has displayed while driving (Figure 2). AND DTC C1A16, C1A16-97, C2582, or C2582-97 is the ONLY DTC stored. Figure 1 Figure 2 This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin. Forward Driving Aids Temporarily Disabled Front Sensor Blocked See Owner’s Manual
NTB19-042F
Service Bulletin/Repair Instructions
AUTOMATIC EMERGENCY BRAKING WARNING LIGHT BLINKING APPLIED SYSTEMS: Vehicles equipped with a lane camera (see Figure 1) SERVICE INFORMATION If the Automatic Emergency Braking (AEB) warning light or is blinking (but not illuminated steadily) or the customer states it is blinking, and there are no related DTCs, inspect the windshield. A blinking AEB warning light may occur under the following conditions: When contamination or foreign material adhere to the lane camera viewing window on the windshield. When driving while it is snowing or when frost forms on the lane camera viewing window on the windshield. When the lane camera viewing window on the windshield is temporarily fogged up. Figure 1 Nissan Bulletins are intended for use by qualified technicians, not 'do-it-yourselfers'. Qualified technicians are properly trained individuals who have the equipment, tools, safety instruction, and know-how to do a job properly and safely. NOTE: If you believe that a described condition may apply to a particular vehicle, DO NOT assume that it does. See your Nissan dealer to determine if this applies to your vehicle. HINT: o Refer to the applicable ESM for diagnosis if DTCs are present in the Laser/Radar, ICC/ADAS, or Lane Camera systems. o For further information: Refer to the following pages. Use the search keyword “blinking” in the ESM.
NTB18-041E
Service Bulletin/Repair Instructions
FALSE ACTIVATION OF AEB, FEB, OR FCW IF YOU CONFIRM The following system(s) falsely activated or the customer reports false activation of: AEB (Automatic Emergency Braking); FEB (Forward Emergency Braking); FCW (Forward Collision Warning) ACTION 1. Check Service COMM or Dealer Business Systems (DBS) National Service History to determine if campaign NTB19-064 applies to this vehicle. If the campaign IS applicable to the vehicle you are working on, then this bulletin does NOT apply. ONLY perform campaign NTB19-064. 2. Refer to Repair Overview on page 2. IMPORTANT: The purpose of ACTION (above) is to give you a quick idea of the work you will be performing. You MUST closely follow the entire SERVICE PROCEDURE as it contains information that is essential to successfully completing this repair.
NTB20-066C
Service Bulletin/Repair Instructions
LANE CAMERA AIMING VEHICLE REFERENCE VALUES NOT IN ESM SERVICE INFORMATION If the lane camera requires aiming, the values in Table A on page 4 must be used. For all other models/model years, consult the Electronic Service Manual (ESM).
NTB19-071D
Service Bulletin/Repair Instructions
DTC B00A0-00 STORED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin. IF YOU CONFIRM DTC B00A0-00 (OCCUPANT DETECTION SENSOR UNIT) is stored, AND OCS zero point reset cannot be performed, (continued on the next page)
NTB12-103I
Service Bulletin/Repair Instructions
CVT/TCM CALIBRATION DATA “WRITE” PROCEDURE This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB10-066C
Service Bulletin/Repair Instructions
CAN COMMUNICATION CODES – DIAGNOSTIC TIPS AND GUIDELINES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB13-027D
Service Bulletin/Repair Instructions
CAN COMMUNICATION – NETWORK DIAGNOSTIC FLOW CHART This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB13-107G
Service Bulletin/Repair Instructions
VEHICLE KEY NOT DETECTED / AUTHENTICATED, ENGINE WILL NOT START This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB21-106B
Service Bulletin/Repair Instructions
DTC C1A17-49 OR C2580-49 STORED IN LASER/RADAR This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB09-081K
Service Bulletin/Repair Instructions
WINDSHIELD CRACKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB13-028I
Service Bulletin/Repair Instructions
REMOVING FOREIGN MATERIAL FROM THE WINDOW GLASS This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB17-019H
Service Bulletin/Repair Instructions
WINDOW GLASS WARRANTY INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB19-042E
Service Bulletin/Repair Instructions
AUTOMATIC EMERGENCY BRAKING WARNING LIGHT BLINKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB23-018G
Service Bulletin/Repair Instructions
SOFTWARE UPDATE FOR INFOTAINMENT ISSUES This bulletin is no longer active. To access infotainment software updates via the Infotainment Software Update Utility: Select SPECIALTY TOOLS, and then select Infotainment Software Updates on the left side of ASIST. Please discard previous versions of NTB23-018.
NTB23-018F
Service Bulletin/Repair Instructions
SOFTWARE UPDATE FOR INFOTAINMENT ISSUES This bulletin is no longer active. To access infotainment software updates via the Infotainment Software Update Utility: Select SPECIALTY TOOLS, and then select Infotainment Software Updates on the left side of ASIST. HINT: Initially, the Infotainment Software Update Utility will be available only on the CONSULT PC version of ASIST. The Utility will be added to ASIST WEB at a later date. Please discard previous versions of NTB23-018.
NTB15-049AA
Service Bulletin/Repair Instructions
TELEMATICS SERVICE INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB17-003F
Service Bulletin/Repair Instructions
FLUID LEAK CAUSED BY TRANSFER ASSEMBLY RIGHT SIDE DRIVE SHAFT OIL SEAL This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB21-094B
Service Bulletin/Repair Instructions
TRANSFER ASSEMBLY SEAL REPLACEMENT FOR AWD FRONT DRIVE SHAFT REMOVAL This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB08-097L
Service Bulletin/Repair Instructions
DIAGNOSIS OF VEHICLE PULL (DRIFT) AND/OR STEERING WHEEL OFF-CENTER This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB23-067
Service Bulletin/Repair Instructions
2014-2020 ROGUE & 2017-2022 ROGUE SPORT; REPLACEMENT JACKKNIFE (FLIP STYLE) KEYS SERVICE INFORMATION For the APPLIED VEHICLES listed above: ï· If the jackknife key is replaced with 80560-4BA1E, the new part provided will no longer be equipped with a key blade. ï· New service parts will have a keyless entry remote with a separate mechanical key. ï· Each vehicle can have a maximum of four (4) keys registered to the BCM. Each service part contains one (1) key and one (1) remote and will use two (2) of the available slots. ï· Follow the SERVICE PROCEDURE starting on page 2 to register the new mechanical key and remote.
NTB23-018E
Service Bulletin/Repair Instructions
SOFTWARE UPDATE FOR INFOTAINMENT ISSUES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB23-018D
Service Bulletin/Repair Instructions
SOFTWARE UPDATE FOR INFOTAINMENT ISSUES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB23-049
Service Bulletin/Repair Instructions
12 VOLT BATTERY TESTING FOR IN-SERVICE VEHICLES SERVICE INFORMATION The following Service Information lists NNA procedural recommendations for establishing good connections while performing 12V battery testing. These recommendations are expected to promote uniformity during the connection process, therefore reducing the number of incorrect âTest with DCAâ and âReplaceâ results. HINT: If 12 volt batteries are allowed to discharge for a prolonged period of time, battery life may be drastically reduced. This condition may lead to premature battery replacement and customer dissatisfaction. IMPORTANT: ï· CPX-900 is now an accepted testing tool to use along with or in place of the DSS-5000 ï· CPX-900 operating instructions are found at: https://nissancpx900.midtronics.com/ ï· DSS-5000 operating instructions are found at: https://nissandss5000.midtronics.com/ ï· DCA-8000 is now a required testing tool to be used for all warranty replacement decisions. The DCA-8000 is also a more efficient charger than previously available, and will charge any available 12 volt lead acid battery safely and accurately as long as all precautions and inputs are made correctly. The DCA-8000 operating instructions are found at: https://nissandca8000.midtronics.com/
NTB23-053
Service Bulletin/Repair Instructions
SILICONE-BASED LUBRICANT OR GREASE CAN DAMAGE ELECTRICAL COMPONENTS SERVICE INFORMATION Do not apply Silicone-based lubricants or grease to, or around, any interior electrical components. To avoid the risk of death or severe personal injury, do not directly spray Silicone-based lubricant or grease, or inadvertently overspray Silicone-based lubricant or grease onto any interior electrical components. These types of lubricants can be detrimental to the proper operation of electrical components.
NTB12-103H
Service Bulletin/Repair Instructions
CVT/TCM CALIBRATION DATA âWRITEâ PROCEDURE This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB13-107F
Service Bulletin/Repair Instructions
VEHICLE KEY NOT DETECTED / AUTHENTICATED, ENGINE WILL NOT START This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB14-012I
Service Bulletin/Repair Instructions
REMOTE ENGINE START NOT WORKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB16-003C
Service Bulletin/Repair Instructions
INTELLIGENT KEY REPLACEMENT OR SWAPPING BETWEEN VEHICLES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.
NTB18-071C
Service Bulletin/Repair Instructions
SECURITY ALARM SOUNDS AFTER USING MECHANICAL KEY TO UNLOCK DRIVER DOOR This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB23-018C
Service Bulletin/Repair Instructions
SOFTWARE UPDATE FOR INFOTAINMENT ISSUES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB03-074Q
Service Bulletin/Repair Instructions
HEADLAMP, FOG LAMP, OR REAR COMBINATION LAMP FOGGING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB12-055J
Service Bulletin/Repair Instructions
CLICKING NOISE FROM FRONT OR REAR AXLE DURING TAKE-OFF/ACCELERATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB19-067H
Service Bulletin/Repair Instructions
SOFTWARE UPDATE FOR INFOTAINMENT ISSUES This bulletin has been superseded by: NTB23-018 SOFTWARE UPDATE FOR INFOTAINMENT ISSUES Please discard previous versions of this bulletin.
NTB23-018B
Service Bulletin/Repair Instructions
SOFTWARE UPDATE FOR INFOTAINMENT ISSUES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB23-018A
Service Bulletin/Repair Instructions
SOFTWARE UPDATE FOR INFOTAINMENT ISSUES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB19-042D
Service Bulletin/Repair Instructions
AUTOMATIC EMERGENCY BRAKING WARNING LIGHT BLINKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB19-071C
Service Bulletin/Repair Instructions
DTC B00A0-00 STORED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB21-106A
Service Bulletin/Repair Instructions
DTC C1A17-49 OR C2580-49 STORED IN LASER/RADAR This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB10-145B
Service Bulletin/Repair Instructions
ABS/VDC CAN DIAGNOSIS INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB23-018
Service Bulletin/Repair Instructions
SOFTWARE UPDATE FOR INFOTAINMENT ISSUES SERVICE INFORMATION When diagnosing an infotainment issue or after replacement of the AV Control Unit, it is necessary to verify the current software version of the AV Control Unit to determine if a software version update is required. Use the vehicle tables in this bulletin to determine the current software version, if the AV Control Unit requires a software version update, and which procedure to use to update the AV Control Unit. The software updates in this bulletin are to address stability improvements and âbugâ fixes. IMPORTANT: If the customer is experiencing a software related concern, refer to NTB21-038 to verify if the customer concern is a hardware or software related issue. If the concern is a software related issue, review the information in this bulletin to update the AV Control Unit as needed.
NTB09-081J
Service Bulletin/Repair Instructions
WINDSHIELD CRACKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB13-028H
Service Bulletin/Repair Instructions
REMOVING FOREIGN MATERIAL FROM THE WINDOW GLASS This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB08-097K
Service Bulletin/Repair Instructions
DIAGNOSIS OF VEHICLE PULL (DRIFT) AND/OR STEERING WHEEL OFF-CENTER This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB10-126C
Service Bulletin/Repair Instructions
WHEEL BEARING COLLISION DAMAGE This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB15-049Z
Service Bulletin/Repair Instructions
TELEMATICS SERVICE INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB22-101
Service Bulletin/Repair Instructions
DRIVE SHAFT BOOT SERVICE INFORMATION SERVICE INFORMATION If a Drive Shaft (Axle Shaft) Boot on an APPLIED VEHICLE is found to be leaking grease, AND There is no abnormal noise or obvious CV Joint risk due to water intrusion and/or complete grease loss, check for REPAIR KIT-DUST BOOT (CV Joint Boot Kit) availability. ï· If there is a REPAIR KIT-DUST BOOT (CV Joint Boot Kit) available for the vehicle being repaired, do NOT replace the axle. Install a new boot kit following the procedure in the ESM. o Refer to the ESM: TRANSMISSION & DRIVELINE > FRONT AXLE > REMOVAL AND INSTALLATION > FRONT DRIVE SHAFT BOOT o If the complete axle (drive shaft) is replaced when only a new boot is required, the over-repair may be charged back to the dealer. ï· If there is NOT a REPAIR KIT-DUST BOOT (CV Joint Boot Kit) available for the vehicle being repaired, refer to the ESM for further diagnostic information. IMPORTANT: When servicing vehicles with staked axle nuts, refer to NTB21-013 to prevent Drive Shaft thread damage.
NTB15-049Y
Service Bulletin/Repair Instructions
TELEMATICS SERVICE INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB10-029I
Service Bulletin/Repair Instructions
ABNORMAL NOISE, VIBRATION AND/OR BINDING FEELING FROM REAR DIFFERENTIAL This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB12-055I
Service Bulletin/Repair Instructions
CLICKING NOISE FROM FRONT OR REAR AXLE DURING TAKE-OFF/ACCELERATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB19-067G
Service Bulletin/Repair Instructions
SOFTWARE UPDATE FOR INFOTAINMENT ISSUES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
REVISION 2 Rogue
Service Bulletin/Repair Instructions
CVT Warranty Extension UPDATE August 30, 2022 Please discard earlier versions of this bulletin. The announcement from June 2, 2022 has been revised to include: ⢠The voucher program ID numbers provided in the FAQ section of this dealer announcement have been changed. The new voucher program ID numbers are: ï Nissan program ID: 22N2299CVT ï INFINITI program ID: 22I2299CVT
NTB19-067F
Service Bulletin/Repair Instructions
SOFTWARE UPDATE FOR INFOTAINMENT ISSUES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB14-012H
Service Bulletin/Repair Instructions
REMOTE ENGINE START NOT WORKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB17-003E
Service Bulletin/Repair Instructions
FLUID LEAK CAUSED BY TRANSFER ASSEMBLY RIGHT SIDE DRIVE SHAFT OIL SEAL This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB21-094A
Service Bulletin/Repair Instructions
TRANSFER ASSEMBLY SEAL REPLACEMENT FOR AWD FRONT DRIVE SHAFT REMOVAL This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
Rogue Pathfinder
Service Bulletin/Repair Instructions
CVT Warranty Extension In an effort to assure customer satisfaction, demonstrate our confidence in continuously variable transmissions (CVTs), and to address customer concerns including those expressed by customers in the class actions, Nissan will extend the warranty coverage on the CVT. The warranty extension includes the CVT assembly and internal CVT components, gaskets, and seals, CVT control valve body, torque converter, cooler kit (if applicable) and reprogramming of the Transmission Control Module (TCM), on the vehicles listed in this announcement. The warranty is being extended from its original duration of 60 months/60,000 miles to 84 months/84,000 miles (whichever occurs first). Coverage of other vehicle components remains unchanged, and all other terms, conditions, limitations and exclusions of Nissanâs New Vehicle Limited Warranty continue to apply. ***** What Dealers Should Do ***** 1. If an owner contacts a dealer with a CVT concern in an owned or leased vehicle, verify warranty coverage for the specific VIN and then inform the customer of any diagnostic charges. NOTE: Some owners may have opted out of the warranty extension by excluding themselves from the class action settlement, thus it is important to check the VIN for each vehicle to verify coverage. 2. Use the appropriate Technical Service Bulletin (TSB) and/or Electronic Service Manual (ESM) to diagnose the root cause of the customer concern and identify the correct repair to resolve the customer concerns. NOTE: Dealers will need to follow the warranty process and obtain pre-approval from the Powertrain Call Center (800-973-9992, option 2) for any vehicles requiring CVT replacements when the replacement cost exceeds a Dealerâs Claims Administration/Authorization Limits (DCAL). Control valves and CVT belt and pulley kits do not require pre-authorization for repairs made under warranty.
NTB10-029H
Service Bulletin/Repair Instructions
NISSAN AWD MODELS; ABNORMAL NOISE, VIBRATION AND/OR JUDDER FROM REAR DIFFERENTIAL This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB19-071B
Service Bulletin/Repair Instructions
DTC B00A0-00 STORED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB19-076C
Service Bulletin/Repair Instructions
DTC P17F0, P17F1, P0776, P2813, P1715, AND/OR P0841 STORED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.
NTB22-026
Service Bulletin/Repair Instructions
SERVICE INFORMATION FOR FUEL GAUGE INACCURATE WITH DTCS STORED IN ECM SERVICE INFORMATION If a fuel level sensor has been diagnosed as sending an incorrect level signal, and one or more of the following DTCs are stored in the ECM, do not replace the entire âFuel Level Sensor Unit, Fuel Filter and Fuel Pump Assemblyâ (fuel pump assembly). The fuel level sensor can be replaced separately. ï· P0460 (FUEL LEV SEN SLOSH) ï· P0461 (FUEL LEVEL SENSOR) ï· P0462 (FUEL LEVL SEN/CIRC) ï· P0463 (FUEL LEVL SEN/CIRC) NOTE: Warranty claims referring to fuel level issues that result in the replacement of the entire fuel pump assembly will be charged back.
2014-2018 Rogue
Service Bulletin/Repair Instructions
Continuously Variable Transmission (CVT) Class Action Owner Notification On March 23, 2022, the Court presiding over a class action lawsuit gave final approval to a proposed settlement under which the CVT warranty will be extended for the following vehicles: 2014-2018 Rogue 2015-2018 Pathfinder *Not including Rogue Hybrid or Pathfinder Hybrid vehicles The approved settlement and the warranty extension are expected to become effective by June 1, 2022. Additional communication will be distributed prior to the warranty extension going into effect. To be clear, for the time being there is no warranty extension, and you should proceed with CVT-related claims as outlined below in bullet point three (3) under What Dealers Should Do. ***** What Dealers Should Do ***** 1. No action is necessary at this time. Nissan will provide additional instructions prior to the effective date of the extended warranty, which is expected to be June 1, 2022. 2. If a customer contacts the dealer with a CVT concern in an owned or leased vehicle, dealers should use the appropriate Technical Service Bulletin (TSB) to diagnose the root cause of the customer concern and identify the correct repair to resolve the customer concerns. NOTE: Dealers will need to follow the warranty process and obtain pre-approval from the Powertrain Call Center (800-973-9992 Option 2) for any vehicles requiring CVT assemblies to be replaced. Valve bodies and CVT belt and pulley kits do not require pre-authorization. 3. If the vehicle is no longer covered by a powertrain or parts warranty, provide owners a repair estimate for test drive, diagnosis, and repair after consulting the goodwill guidelines available in the Assurance Product Resources Manual (APRM) or WBP/18-006.
NTB10-029G
Service Bulletin/Repair Instructions
NISSAN AWD MODELS; ABNORMAL NOISE, VIBRATION AND/OR JUDDER FROM REAR DIFFERENTIAL This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB15-049X
Service Bulletin/Repair Instructions
TELEMATICS SERVICE INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB17-003D
Service Bulletin/Repair Instructions
FLUID LEAK CAUSED BY TRANSFER ASSEMBLY RIGHT SIDE DRIVE SHAFT OIL SEAL This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB13-027C
Service Bulletin/Repair Instructions
CAN COMMUNICATION â NETWORK DIAGNOSTIC FLOW CHART This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB18-071B
Service Bulletin/Repair Instructions
SECURITY ALARM SOUNDS AFTER USING MECHANICAL KEY TO UNLOCK DRIVER DOOR This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB17-003C
Service Bulletin/Repair Instructions
FLUID LEAK CAUSED BY TRANSFER ASSEMBLY RIGHT SIDE DRIVE SHAFT OIL SEAL This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB13-097J
Service Bulletin/Repair Instructions
EVAP LEAK DTC P0442, P0455, P0456 INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB17-082E
Service Bulletin/Repair Instructions
DTC P0456 CAUSED BY EVAP LEAK AT VENT CONTROL VALVE O-RING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB17-045C
Service Bulletin/Repair Instructions
CLEANING FRONT OR REAR COMBINATION LAMP ASSEMBLIES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB19-076B
Service Bulletin/Repair Instructions
2018 ALTIMA AND 2018-2019 ROGUE; DTC P17F0, P17F1, P0776, P2813, P1715, AND/OR P0841 STORED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.
NTB99-001F
Service Bulletin/Repair Instructions
STRUT AND SHOCK ABSORBER REPLACEMENT GUIDELINES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB21-106
Service Bulletin/Repair Instructions
DTC C1A17-49 OR C2580-49 STORED IN LASER/RADAR SERVICE INFORMATION If DTC C1A17-49 or C2580-49 is stored in LASER/RADAR in the âPASTâ column: ï· Erase the DTC. ï· DO NOT replace any parts. If DTC C1A17-49 or C2580-49 is stored in LASER/RADAR in the "CURRENT" column, refer to the applicable ESM for instructions.
NTB21-094
Service Bulletin/Repair Instructions
TRANSFER ASSEMBLY SEAL REPLACEMENT FOR AWD FRONT DRIVE SHAFT REMOVAL SERVICE INFORMATION When removing the front passenger (RH) side drive shaft on an applied vehicle for any reason, transfer assembly drive shaft oil seal and dust cover seal replacement is required. Refer to the SERVICE PROCEDURE in this bulletin.
NTB18-055E
Service Bulletin/Repair Instructions
CVT FLUID LEVEL QUICK CHECK GAUGE This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB12-055H
Service Bulletin/Repair Instructions
CLICKING NOISE FROM FRONT OR REAR AXLE DURING TAKE-OFF/ACCELERATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB15-077D
Service Bulletin/Repair Instructions
SIGNAL TECH-II INTELLIGENT KEY BATTERY TEST AND SIGNAL CHECK This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB16-028D
Service Bulletin/Repair Instructions
INTELLIGENT KEY BUTTONS INOPERATIVE BUT REQUEST SWITCHES WORK This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB17-118B
Service Bulletin/Repair Instructions
NISSAN; INTELLIGENT KEY IDENTIFICATION AND REGISTRATION TIPS This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB17-003B
Service Bulletin/Repair Instructions
FLUID LEAK CAUSED BY TRANSFER ASSEMBLY RIGHT SIDE DRIVE SHAFT SEAL This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB21-035
Service Bulletin/Repair Instructions
2018-2021 LEAF AND 2017-2020 ROGUE; STEERING WHEEL CHROME FINISHER REPLACEMENT SERVICE INFORMATION If the chrome finisher on the steering wheel needs to be replaced, the chrome finisher can be ordered separately from the steering wheel. SERVICE PROCEDURE 1. Remove the driver side air bag module. ï· For removal of the driver side air bag module, refer to the Electronic Service Manual (ESM), section REPAIR â RESTRAINTS â SRS AIRBAG â REMOVAL AND INSTALLATION â DRIVER AIR BAG MODULE. NOTE: ï· When removing the chrome finisher from the steering wheel, reference Figure 2 for the 6 attachment points. ï· During removal of the chrome finisher (step 2 on page 3), pull on the chrome finisher just enough to release the pawls from the steering wheel.
NTB16-018D
Service Bulletin/Repair Instructions
MIL ON WITH P0603 STORED FOR ECM BACK UP CIRCUIT This bulletin has been amended. See AMENDMENT HISTORY on page 3. Please discard previous versions of this bulletin.
NTB15-049W
Service Bulletin/Repair Instructions
TELEMATICS SERVICE INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB18-008A
Service Bulletin/Repair Instructions
ADAS SYSTEM DTC C1A03, C1A04, AND/OR C1B01 SERVICE INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB18-041D
Service Bulletin/Repair Instructions
2017-2020 ROGUE, ROGUE HYBRID, AND ROGUE SPORT; FALSE ACTIVATION OF AEB, FEB, OR FCW This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB17-118A
Service Bulletin/Repair Instructions
NISSAN; INTELLIGENT KEY IDENTIFICATION AND REGISTRATION TIPS This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB15-077C
Service Bulletin/Repair Instructions
NISSAN; SIGNAL TECH-II INTELLIGENT KEY BATTERY TEST AND SIGNAL CHECK This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB16-028C
Service Bulletin/Repair Instructions
INTELLIGENT KEY BUTTONS INOPERATIVE BUT REQUEST SWITCHES WORK This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB17-097B
Service Bulletin/Repair Instructions
2016-2018 ROGUE AND 2017-2018 ROGUE SPORT; WHISTLE NOISE TRANSMITTED TO CALL RECIPIENT WHEN USING BLUETOOTH HANDS-FREE PHONE SYSTEM This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB18-023A
Service Bulletin/Repair Instructions
NISSAN; MICROPHONE DOES NOT WORK This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.
NTB19-071A
Service Bulletin/Repair Instructions
DTC B00A0-00 STORED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB15-013f
Service Bulletin/Repair Instructions
NISSAN; PROCEDURE TO CLEAN CVT TRANSMISSION FLUID COOLERS This bulletin is no longer active. Please discard previous versions of NTB15-013. Refer to the ESM for the fluid cooler cleaning procedure.
NTB99-001e
Service Bulletin/Repair Instructions
STRUT AND SHOCK ABSORBER REPLACEMENT GUIDELINES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB18-071a
Service Bulletin/Repair Instructions
SECURITY ALARM SOUNDS AFTER USING MECHANICAL KEY TO UNLOCK DRIVER DOOR This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB19-008b
Service Bulletin/Repair Instructions
NISSAN; DIAGNOSIS INFORMATION FOR DTC P161D This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB19-067e
Service Bulletin/Repair Instructions
SOFTWARE UPDATE FOR INFOTAINMENT ISSUES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB19-031a
Service Bulletin/Repair Instructions
BEEPING NOISE WHILE TRAVELING THROUGH OPEN AREA This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB19-042b
Service Bulletin/Repair Instructions
AEB WARNING LIGHT BLINKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB19-064c
Service Bulletin/Repair Instructions
VOLUNTARY SERVICE CAMPAIGN 2017-2018 ROGUE, ROGUE HYBRID, AND ROGUE SPORT; ICC/ADAS AND LASER/RADAR REPROGRAMMING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB20-066b
Service Bulletin/Repair Instructions
LANE CAMERA AIMING VEHICLE REFERENCE VALUES NOT IN ESM This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB17-119a
Service Bulletin/Repair Instructions
2018 ROGUE; INTELLIGENT KEY REGISTRATION TIPS This bulletin is no longer active. Please discard previous versions of NTB17-119.
NTB15-049v
Service Bulletin/Repair Instructions
TELEMATICS SERVICE INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB20-043a
Service Bulletin/Repair Instructions
2014-2020 ROGUE; AIR DUCT REPLACEMENT This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB14-105a
Service Bulletin/Repair Instructions
2014-2020 ROGUE; CARPET WET FRONT FLOOR AREA This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.
NTB12-110d
Service Bulletin/Repair Instructions
POWER BACK DOOR CALIBRATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.
NTB20-094
Service Bulletin/Repair Instructions
2015-2020 ROGUE; MIL ON WITH DTC P0181 AND/OR P0183 IF YOU CONFIRM The MIL is ON with DTC P0181 (FTT SENSOR) and/or P0183 (FTT SEN/CIRCUIT) stored in the ECM. ACTION 1. Remove the fuel pump assembly. 2. Inspect the fuel pump assembly wiring, and reroute the wiring, if applicable. 3. Reinstall the fuel pump assembly.
NTB17-083b
Service Bulletin/Repair Instructions
MOTION ACTIVATED LIFTGATE STICKER This bulletin is no longer active. Please discard previous versions of NTB17-083.
NTB20-090a
Service Bulletin/Repair Instructions
2014-2020 ROGUE; HVAC BLOWER NOISY OR WATER DRIPS ON DRIVER SIDE CARPET This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB20-090
Service Bulletin/Repair Instructions
2014-2020 ROGUE; HVAC BLOWER NOISY OR WATER DRIPS ON DRIVER SIDE CARPET IF YOU CONFIRM The customer states the HVAC blower is noisy OR Water is dripping on the driver side carpet after going through a car wash. ACTION Refer to REPAIR OVERVIEW on page 2.
NTB15-026d
Service Bulletin/Repair Instructions
2014-2020 ROGUE; LACKS POWER DUE TO SNOW INGESTION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
DOR-H5Y5B-01
Service Bulletin/Repair Instructions
This SKU is a Suspension Ball Joint. The customer communication requested return of unsold inventory to inspect for the outer diameter of the ball joint housing being too small. The outer diameter being too small would prevent the part from being installed, and would therefore have no impact on the end user besides time to complete installation.
NTB19-067d
Service Bulletin/Repair Instructions
SOFTWARE UPDATE FOR INFOTAINMENT ISSUES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB19-042a
Service Bulletin/Repair Instructions
AEB WARNING LIGHT BLINKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB20-075
Service Bulletin/Repair Instructions
SOFTWARE UPDATE POP-UP NOTIFICATION SERVICE INFORMATION The infotainment system of the applied vehicle has the ability to update its software through an over-the-air (OTA) link. As software updates become available for new features, and/or patches, the software update screen (pop-up) shown in Figure 1 will automatically be displayed. Much like cell phone and computer updates, this is a normal feature which allows the user to choose when an update is downloaded. ï· It is recommended that while in dealer inventory and this pop-up appears, that â Yesâ is selected to provide the latest software version to the customer at delivery. NOTE: If the ignition is turned OFF in the middle of a download, it will automatically restart when the ignition is turned back ON. When one of the following is selected: Yesâ¦..The pop-up is hidden and the download starts in the background. Laterâ¦The pop-up is hidden and displayed again in the next key cycle (after cold start).
NTB19-076a
Service Bulletin/Repair Instructions
2018 ALTIMA AND 2018-2019 ROGUE; DTC P17F0, P17F1, P0776, P2813, P1715, AND/OR P0841 STORED IF YOU CONFIRM One or more of the following DTCs are stored: P0776, P2813, P0841, P17F0, P17F1, P1715 HINT: ï· If DTCs other than those listed above are stored, this bulletin does not apply. ï· If the customer states the engine stalled while going from 'P' or 'N' range to 'R' or 'D' range, this bulletin does not apply. ï· If DTC P17F0 and/or P17F1 are the only DTCs stored and there is no customer complaint of judder, this bulletin does not apply. ï· If DTC P1715 is the only code stored, this bulletin does not apply. ACTION See Repair Flow Chart on page 2 to confirm if this bulletin applies. HINT: The following pages must be printed and attached to the RO: 1. Clutch Total End Play Calculation (Step 97 on page 63) 2. Consult screen shot showing the TCM part numbers (Step 152 on page 89) 3. Current Calibration Data (Step 155 on page 90) 4. New Calibration Data (Step 171 on page 91) 5. Parts Kit Reference Table (Page 99)
NTB20-066a
Service Bulletin/Repair Instructions
LANE CAMERA AIMING VEHICLE REFERENCE VALUES NOT IN ESM This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB20-069
Service Bulletin/Repair Instructions
ROGUE AND ROGUE SPORT; VIBRATION AND/OR NOISE WHEN MAKING LOW SPEED TURNS IF YOU CONFIRM There is a vibration or judder feeling from the rear of the vehicle during the following conditions: ï· When making turns ï· On dry roads ï· At low speeds (under 40 MPH) And ï· The above vibration does not occur if the electric controlled coupling is electrically disconnected. ACTION 1. Confirm the AWD control unit part number, and replace it, if applicable. 2. Replace the electric controlled coupling for the rear final drive. 3. Perform Unit Characteristics Writing.
NTB20-066
Service Bulletin/Repair Instructions
LANE CAMERA AIMING VEHICLE REFERENCE VALUES NOT IN ESM SERVICE INFORMATION If the lane camera requires aiming, the values in Table A on page 4 must be used. ï· For all other models/model years, consult the Electronic Service Manual (ESM). The following CONSULT-III plus (C-III plus) figures and steps are only provided to indicate where the VEHICLE REFERENCE VALUE from Table A is to be entered. The entire camera aiming procedure must be followed to complete the aiming procedure. ï· Refer to the ESM section: CRUISE CONTROL & DRIVER ASSISTANCE > DRIVER ASSISTANCE SYSTEM > DRIVER ASSISTANCE SYSTEM > BASIC INSPECTION > LANE CAMERA UNIT > CAMERA AIMING ADJUSTMENT. 1. Turn the ignition ON. 2. From the C-III plus home screen, select Diagnosis (One System).
NTB20-050
Service Bulletin/Repair Instructions
POWER BACK DOOR WILL NOT OPERATE WITH REQUEST SWITCHES IF YOU CONFIRM On vehicles equipped with a Kick Motion Activated Liftgate, the back door (liftgate) will not open or close when requested to do so using the: ï· Intelligent Key ï· Back door request switch, located on the back door ï· Automatic back door switch, located on the instrument lower panel LH And DTC B2409 is either current or has been stored in the past. ACTION Replace the automatic back door control module. ï· Refer to the Electronic Service Manual (ESM) section: BODY EXTERIOR, DOORS, ROOF & VEHICLE SECURITY > DOOR & LOCK > WITH INTELLIGENT KEY SYSTEM > REMOVAL AND INSTALLATION > AUTOMATIC BACK DOOR CONTROL MODULE.
NTB18-033b
Service Bulletin/Repair Instructions
ACCELERATOR PEDAL VIBRATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB19-067c
Service Bulletin/Repair Instructions
SOFTWARE UPDATE FOR INFOTAINMENT ISSUES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB20-043
Service Bulletin/Repair Instructions
2015-2020 ROGUE; AIR DUCT REPLACEMENT IF YOU CONFIRM Air duct 1, air duct 2, or the air cleaner cover shown in Figure 1 needs to be replaced. ACTION Inspect for a clip in the location shown in Figure 1 and Figure 2. ï· If a clip is present, then the vehicle IS equipped with the updated parts; no further action is needed. Individual parts may be replaced as needed. ï· If a clip is NOT present, then the vehicle is equipped with older parts. See SERVICE PROCEDURE on the next page.
NTB15-049u
Service Bulletin/Repair Instructions
TELEMATICS SERVICE INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB20-025a
Service Bulletin/Repair Instructions
VOLUNTARY EMISSIONS RECALL CAMPAIGN 2018 ALTIMA AND ROGUE; CYLINDER HEAD This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard previous versions of this bulletin.
NTB20-027a
Service Bulletin/Repair Instructions
VOLUNTARY EMISSIONS RECALL CAMPAIGN 2018 ALTIMA AND ROGUE; EXHAUST MANIFOLD AND THREE WAY CATALYST ASSEMBLY This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard previous versions of this bulletin.
PC716_PC717 2018
Service Bulletin/Repair Instructions
QR25 Cylinder Head Voluntary Emission Recall Campaign ***** Campaign Summary ***** Nissan is conducting a Voluntary Emission Recall Campaign on approximately 2,209 specific MY2018 Nissan Rogue (T32) and 5,557 specific MY2018 Altima (L33) 2.5L vehicles identified in Service Comm to inspect the engine identification markings and, if they are from the subject manufacturing lot, the suspect cylinders and spark plugs will be inspected. If necessary, dealers may replace the engine, exhaust manifold catalyst, air fuel (A/F) ratio sensor, and oxygen sensor. A machining issue in the engine may exist, which could allow oil to escape past the valve guides and enter the combustion chamber. If an affected engine is not repaired, the performance of the manifold catalyst could degrade over time and cause exhaust gas emissions to exceed standards at high mileage. This incident has no effect on safety or fuel consumption but may decrease engine performance in rare cases. If Nissan has previously replaced the engine in the vehicle due to this condition, the exhaust manifold catalyst, air fuel (A/F) ratio sensor, and oxygen sensor will be replaced. ***** What Dealers Should Do**** 1. Verify campaign applicability using Service Comm or DBS National Service History â Open Campaign I.D. ï· PC716 - Inspect Engine Identification Markings ï· PC717 - Manifold Catalyst Replacement 2. Dealers should use the appropriate campaign bulletin to remedy any vehicles subject to these campaigns: ï· PC716 â NTB20-025 ï· PC717 â NTB20-027 3. Once repaired, dealers should submit the claim, using the claims coding provided, and release the vehicle.
NTB20-025
Service Bulletin/Repair Instructions
VOLUNTARY EMISSIONS RECALL CAMPAIGN 2018 ALTIMA AND ROGUE; CYLINDER HEAD INTRODUCTION Nissan is conducting this voluntary emissions recall campaign on certain specific model year 2018 Altima and Rogue vehicles. The cylinder head will be inspected, and the long engine assembly replaced if needed. This service will be performed at no charge to the customer for parts or labor. IDENTIFICATION NUMBER Nissan has assigned identification number PC716 to this campaign. This number must appear on all communication and documentation of any nature dealing with this campaign. DEALER RESPONSIBILITY It is the dealerâs responsibility to check Service COMM or Dealer Business Systems (DBS) National Service History for the campaign status on each vehicle falling within the range of this voluntary emissions recall which for any reason enters the service department. This includes vehicles purchased from private parties or presented by transient (tourist) owners and vehicles in a dealerâs inventory. Federal law requires that new vehicles in dealer inventory which are the subject of an emissions recall must be corrected prior to sale. Failure to do so can result in civil penalties. While federal law applies only to new vehicles, Nissan strongly encourages dealers to correct any used vehicles in their inventory before they are retailed.
NTB20-027
Service Bulletin/Repair Instructions
VOLUNTARY EMISSIONS RECALL CAMPAIGN 2018 ALTIMA AND ROGUE; EXHAUST MANIFOLD AND THREE WAY CATALYST ASSEMBLY INTRODUCTION Nissan is conducting this voluntary emissions recall campaign on certain specific model year 2018 Altima and Rogue vehicles. The exhaust manifold and three way catalyst assembly and two exhaust sensors will be replaced. This service will be performed at no charge to the customer for parts or labor. IDENTIFICATION NUMBER Nissan has assigned identification number PC717 to this campaign. This number must appear on all communication and documentation of any nature dealing with this campaign. DEALER RESPONSIBILITY It is the dealerâs responsibility to check Service COMM or Dealer Business Systems (DBS) National Service History for the campaign status on each vehicle falling within the range of this voluntary emissions recall which for any reason enters the service department. This includes vehicles purchased from private parties or presented by transient (tourist) owners and vehicles in a dealerâs inventory. Federal law requires that new vehicles in dealer inventory which are the subject of an emissions recall must be corrected prior to sale. Failure to do so can result in civil penalties. While federal law applies only to new vehicles, Nissan strongly encourages dealers to correct any used vehicles in their inventory before they are retailed.
NTB17-003a
Service Bulletin/Repair Instructions
FLUID LEAK CAUSED BY TRANSFER ASSEMBLY RIGHT SIDE DRIVE SHAFT SEAL This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB18-055d
Service Bulletin/Repair Instructions
CVT FLUID LEVEL QUICK CHECK GAUGE This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB15-049t
Service Bulletin/Repair Instructions
TELEMATICS SERVICE INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB12-055g
Service Bulletin/Repair Instructions
CLICKING NOISE FROM FRONT OR REAR AXLE DURING TAKE-OFF/ACCELERATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB17-057c
Service Bulletin/Repair Instructions
2015-2020 ROGUE AND 2017-2020 ROGUE SPORT; DISTANCE TO EMPTY DOES NOT RESET This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB15-013e
Service Bulletin/Repair Instructions
NISSAN; PROCEDURE TO CLEAN CVT TRANSMISSION FLUID COOLERS This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB19-080
Service Bulletin/Repair Instructions
2014-2020 ROGUE; NO AIR FLOW FROM VENTS DUE TO SNOW BUILD-UP IF YOU CONFIRM Or the customer states there is no air flow from any of the HVAC vents And There is snow build-up in and around the blower motor air inlet, behind the cowl. ACTION 1. Remove all snow, water, and debris from the blower motor inlet, cowl area, and where the blower motor mounts. 2. Clean or replace the blower motor as needed. 3. If the blower motor does not work on all speed settings, replace the variable blower control (fan resistor). 4. If not already equipped: Install the cowl and wiper pivot filters listed in PARTS INFORMATION on the last page of this bulletin.
White Paint Clas
Service Bulletin/Repair Instructions
White Paint Class Action Owner Notification Dealer Notification In October, owners of white Nissan Rogues produced between January 11, 2013 and April 23, 2013, will receive a notice from a settlement administrator informing them of the terms of a proposed class action settlement. The settlement, if approved by the presiding court, could extend the warranty on the paint for four years and provide a one-time full vehicle repaint (subject to a copay). Eligible owners can also obtain coverage for any reasonable and necessary rental car coverage arising from the repaint, or reimbursement of amounts previously incurred for a one-time repaint and any reasonable and necessary rental car services arising from the repaint. The settlement also provides for eligibility in Nissanâs Vehicle Purchase Program. To be clear, unless and until the proposed settlement is approved by the presiding court, there is no warranty extension or other remedy and you should proceed with paint-related claims in the ordinary course. The proposed settlement, and the associated potential warranty extension, include many terms and conditions. Rather than attempting to address questions about the proposed settlement terms from customers, Nissan recommends dealers refer customers to the website listed below. This will enable owners to receive information from appropriate sources and avoid providing incorrect and/or incomplete information to customers. The website is currently live and available to inquiring customers. ***** What Dealers Should Do ***** 1. No action is necessary at this time. Nissan will provide additional instructions once the proposed settlement is approved by the court. 2. If a customer contacts the dealer with a white paint concern and/or references this settlement notification, dealers should refer the customer to the third party administratorâs website for additional information. www.vehiclepaintsettlement.com
NTB19-076
Service Bulletin/Repair Instructions
2018 ALTIMA AND ROGUE; DTC P17F0, P17F1, P0776, P2813, P1715, AND/OR P0841 STORED IF YOU CONFIRM One or more of the following DTCs are stored: P0776, P2813, P0841, P17F0, P17F1, P1715 HINT: ï· - If DTCs other than those listed above are stored, this bulletin does not apply. ï· - If the customer states the engine stalled while going from 'P' or 'N' range to 'R' or 'D' range, this bulletin does not apply. ï· - If DTC P17F0 and/or P17F1 are the only DTCs stored and there is no customer complaint of judder, this bulletin does not apply. ï· - If DTC P1715 is the only code stored, this bulletin does not apply. ACTION See Repair Flow Chart on page 2 to confirm if this bulletin applies. HINT: The following pages must be printed and attached to the RO: 1. Clutch Total End Play Calculation (Step 97 on page 63) 2. Consult screen shot showing the TCM part numbers (Step 152 on page 89) 3. Current Calibration Data (Step 155 on page 90) 4. New Calibration Data (Step 171 on page 91) 5. Parts Kit Reference Table (Page 99)
NTB17-028a
Service Bulletin/Repair Instructions
2014-2020 ROGUE; BLOWER MOTOR SERVICE INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB19-064b
Service Bulletin/Repair Instructions
VOLUNTARY SERVICE CAMPAIGN 2017-2018 ROGUE, ROGUE HYBRID, AND ROGUE SPORT; ICC/ADAS AND LASER/RADAR REPROGRAMMING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB19-067b
Service Bulletin/Repair Instructions
SOFTWARE UPDATES FOR INFOTAINMENT ISSUES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB19-072
Service Bulletin/Repair Instructions
TRANSMISSION RANGE SWITCH SERVICE INFORMATION SERVICE INFORMATION The transmission range switch of the APPLIED VEHICLES listed above is now available as a separate service part. If the transmission range switch of an APPLIED VEHICLE is being replaced for any reason, it must be adjusted after its replacement. ï· Refer to SERVICE PROCEDURE on page 3 for transmission range switch removal, installation, and adjustment.
NTB19-071
Service Bulletin/Repair Instructions
DTC B00A0-00 STORED IF YOU CONFIRM DTC B00A0-00 (OCCUPANT DETECTION SENSOR UNIT) is stored And OCS zero point reset cannot be performed (continued on the next page) And The following screen displays: ACTION 1. Check the Occupant Classification System (OCS) control unit using the ODS Analysis tool software. ï· Refer to SERVICE PROCEDURE on page 5. HINT: âOCSâ may also be referred to as âODSâ. 2. Perform â75-zero RESETâ.
NTB19-067a
Service Bulletin/Repair Instructions
SOFTWARE UPDATES FOR INFOTAINMENT ISSUES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB19-064a
Service Bulletin/Repair Instructions
VOLUNTARY SERVICE CAMPAIGN 2017-2018 ROGUE, ROGUE HYBRID, AND ROGUE SPORT; ICC/ADAS AND LASER/RADAR REPROGRAMMING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB17-111d
Service Bulletin/Repair Instructions
NISSANCONNECT OVER THE AIR SOFTWARE UPDATE This bulletin has been superseded by NTB19-067. Please discard previous versions of this bulletin.
NTB19-067
Service Bulletin/Repair Instructions
SOFTWARE UPDATES FOR INFOTAINMENT ISSUES SERVICE INFORMATION When diagnosing an infotainment issue, always confirm that the latest software is installed in the AV unit before starting the diagnosis. The software updates in the following Service Procedure are for the items below: ï· Stability improvements and bug fixes ï· System enhancements that will allow future Over-The-Air (OTA) updates. Without these software updates, future OTAs will not be possible. Refer to step 5 on page 5 to confirm that this bulletin applies. HINT: The update software only needs to be downloaded once and can then be used on multiple Applied Vehicles until other infotainment software is loaded onto the USB drive to overwrite the original data.
NTB18-041c
Service Bulletin/Repair Instructions
2017-2020 ROGUE, ROGUE HYBRID, AND ROGUE SPORT; FALSE ACTIVATION OF AEB, FEB, OR FCW This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB17-113b
Service Bulletin/Repair Instructions
2017-2018 ROGUE SPORT; WHEN COLD LONG CRANK TIME, ENGINE TURNS OFF, HESITATION, ROUGH IDLE, OR MISFIRE This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NPSB18-443B AEB
Service Bulletin/Repair Instructions
2017-2018 Rogue and Rogue Sport Automatic Emergency Braking (AEB) Update Notification Letter REVISED August 27, 2019 Please discard earlier versions of this bulletin. This bulletin has been superseded by campaign ID P9327. Please refer to the Voluntary Service Campaign announcement associated with this campaign ID for additional information.
P9327 Rogue - Au
Service Bulletin/Repair Instructions
Automatic Emergency Braking (AEB) Voluntary Service Campaign ***** Campaign Summary***** Nissan is committed to the safety, security and satisfaction of our customers and their passengers. Nissan is upgrading an existing Customer Service Initiative to a Voluntary Service Campaign on certain Model Year 2017-18 Rogue (T32), Rogue Sport (J11), and Rogue Hybrid (T32H) vehicles to reprogram the Radar and Advanced Driver Assistance System (ADAS) components of the Automatic Emergency Braking (AEB) system. Covered vehicles that were not updated under NPSB/18-443 will be reprogrammed with updated software to improve system functionality through reduced false positive AEB activation in certain driving environments. In rare instances and unique roadway environments such as certain types of railroad crossings and metal overpasses, the AEB system in some vehicles may activate braking when it is not needed. The driver can always override the AEB system by pressing the accelerator. Nissan previously invited customers that had experienced an issue with their AEB system to come in for updated software before their Limited Vehicle Warranty expired. Now, Nissan is encouraging owners to have this important software update performed without regard to any issues or warranty status. ***** What Dealers Should Do ***** 1. Verify if vehicles are affected by this Voluntary Service Campaign using Service Comm or DBS National Service History - Open Campaign I.D. P9327. 2. Dealers should reprogram the Radar and ADAS software on any affected vehicles in retailer new or pre-owned inventory to help ensure customer satisfaction. 3. Dealers should use NTB19-064 to inspect and, if necessary, remedy any vehicles subject to this campaign. 4. The service department should submit the applicable warranty claim for the action performed so it can be closed on Service Comm and release the vehicle.
NTB19-064
Service Bulletin/Repair Instructions
VOLUNTARY SERVICE CAMPAIGN 2017-2018 ROGUE, ROGUE HYBRID, AND ROGUE SPORT; ICC/ADAS AND LASER/RADAR REPROGRAMMING INTRODUCTION Nissan is conducting this voluntary service campaign on certain specific model year 2017-2018 Rogue, Rogue Hybrid, and Rogue Sport vehicles to reprogram the Laser/Radar and/or ICC/ADAS control units. This service will be performed at no charge to the customer for parts or labor. IDENTIFICATION NUMBER Nissan has assigned identification number P9327 to this campaign. This number must appear on all communication and documentation of any nature dealing with this campaign. DEALER RESPONSIBILITY Dealers are to repair vehicles falling within range of this campaign that enter the service department. This includes vehicles purchased from private parties, vehicles presented by transient (tourists) owners, and vehicles in a dealerâÂÂs inventory.
NTB14-012e
Service Bulletin/Repair Instructions
REMOTE ENGINE START NOT WORKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB18-077a
Service Bulletin/Repair Instructions
MIL ON WITH DTC P0776, P1715 AND MAY HAVE HESITATION AND/OR LACK OF POWER This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB15-049s
Service Bulletin/Repair Instructions
TELEMATICS SERVICE INFORMATION This bulletin applies only to vehicles equipped with a Telematics Communication Unit (TCU). This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB18-019a
Service Bulletin/Repair Instructions
2013-2018 ALTIMA AND 2014-2018 ROGUE; ENGINE SUPPORT TOOLS This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB18-055c
Service Bulletin/Repair Instructions
CVT FLUID LEVEL QUICK CHECK GAUGE This bulletin applies only to vehicles equipped with a Continuously Variable Transmission (CVT). This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB19-042
Service Bulletin/Repair Instructions
AEB WARNING LIGHT BLINKING This bulletin applies only to vehicles equipped with a lane camera. SERVICE INFORMATION If the AEB warning light is blinking (but not illuminated steadily) or the customer states it is blinking, and there are no related DTCs, inspect the windshield. A blinking AEB warning light may occur under the following conditions: - When contamination or foreign material adhere to the lane camera viewing window on the windshield - When driving while it is snowing or when frost forms on the lane camera viewing window on the windshield - When the lane camera viewing window on the windshield is temporarily fogged up NOTE: - If DTCs are present in any of the following related systems: - Laser/Radar, - ICC/ADAS, or - Lane Camera, Refer to the related Electronic Service Manual (ESM) for diagnosis. - Refer to the following pages for further information.
NTB19-039
Service Bulletin/Repair Instructions
2017 ? 2018 ROGUE SPORT; AIR DUCT REPLACEMENT IF YOU CONFIRM If air duct 1, air duct 2, or air cleaner cover shown in Figure 1 need to be replaced ACTION Inspect for a clip in the location shown in Figure 1 and Figure 2. - If a clip is present, then the vehicle IS equipped with the updated parts; no further action is needed. Individual parts may be replaced as needed. - If a clip is NOT present, then the vehicle is equipped with older parts. See SERVICE PROCEDURE on the next page.
NTB19-008a
Service Bulletin/Repair Instructions
NISSAN; DIAGNOSIS INFORMATION FOR DTC P161D This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB19-031
Service Bulletin/Repair Instructions
BEEPING NOISE WHILE TRAVELING THROUGH OPEN AREA IF YOU CONFIRM Customer reports continuous beeping noise and/or the Driving Aids screen shown in Figure 1 flashes, especially when driving in open areas similar to Figure 2. ACTION Refer to TABLE A on page 8 to confirm if ICC/ADAS 2 control unit reprogramming is needed.
NTB12-100b
Service Bulletin/Repair Instructions
CVT / TCM CALIBRATION DATA ?WRITE? PROCEDURE This bulletin applies only to vehicles equipped with a Continuously Variable Transmission (CVT). This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB12-103g
Service Bulletin/Repair Instructions
CVT / TCM CALIBRATION DATA ?WRITE? PROCEDURE This bulletin applies only to vehicles equipped with a Continuously Variable Transmission (CVT). This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB18-055b
Service Bulletin/Repair Instructions
CVT FLUID LEVEL QUICK CHECK GAUGE This bulletin applies only to vehicles equipped with a Continuously Variable Transmission (CVT). This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.
NTB18-041b
Service Bulletin/Repair Instructions
2017-2018 ROGUE, ROGUE HYBRID, AND ROGUE SPORT; FALSE ACTIVATION OF AEB, FEB, OR FCW This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NPSB18-443a
Service Bulletin/Repair Instructions
2017-2018 Rogue and Rogue Sport Automatic Emergency Braking (AEB) Update Notification Letter Nissan is conducting an important Customer Service Initiative to increase awareness of an available update for the Automatic Emergency Braking (AEB) system on certain Model Year 2017-18 Rogue (T32), Rogue Sport (J11), and Rogue Hybrid (T32) vehicles. In rare instances and unique roadway environments such as certain types of railroad crossings and metal overpasses, the AEB system in some vehicles may activate braking when not needed. The driver can always override the AEB system by pressing the accelerator. Nissan has developed a special AEB system update that is available to owners at no cost for parts and labor during the duration of the Basic Coverage under their New Vehicle Limited Warranty (3 years/36,000 miles, whichever comes first). This update will enhance system performance for customers that wish to proactively update their vehicle or for customers that have experienced this issue. THIS CUSTOMER SERVICE INITIATIVE IS IMPLEMENTED TO MAKE CUSTOMERS AWARE OF AN AVAILABLE UPDATE. THIS INITIATIVE IS NOT A WARRANTY, AN EXTENSION OF THE NEW VEHICLE LIMITED WARRANTY, OR AN IMPLIED OR GENERAL WARRANTY, AND IS NOT CONNECTED TO ANY SALE OF THE VEHICLE.
NTB19-022
Service Bulletin/Repair Instructions
NISSAN; P0171 AND P0174 SERVICE INFORMATION SERVICE INFORMATION Diagnosis for DTCs P0171 (FUEL SYS LEAN B1) and P0174 (FUEL SYS LEAN B2) have been revised for the APPLIED VEHICLES listed above. When performing diagnosis for either of these DTCs, start by using the SERVICE PROCEDURE section of this bulletin. NOTE: The related Electronic Service Manuals (ESM) will be revised in the future to include these diagnostic steps.
NTB19-021
Service Bulletin/Repair Instructions
NISSAN; MIL ON WITH DTC P219A AND/OR P219B STORED This bulletin applies to Titan XD vehicles equipped with a VK56D gas engine only. SERVICE INFORMATION If the MIL is ON and DTC P219A (AIR FUEL RATIO IMBALANCE B1) and/or P219B (AIR FUEL RATIO IMBALANCE B2) is stored: - DO NOT replace the Air Fuel Ratio (A/F) sensor. - Refer to the applicable Electronic Service Manual (ESM) and follow the diagnostic procedure for DTC P219A and/or P219B.
NTB19-012
Service Bulletin/Repair Instructions
2017-2018 ROGUE SPORT; SURGE FEEL AT CONSTANT SPEED IF YOU CONFIRM Customer claims "surge feel? at a constant speed more than 25mph And The CONTROLLER ASSY IDM (CHASSIS CONTROL) part number is 476A0-6MA0A or 476A0-6MG0A. ACTION Reprogram the CONTROLLER ASSY IDM per the Service Procedure in this bulletin.
NTB16-028b
Service Bulletin/Repair Instructions
INTELLIGENT KEY BUTTONS INOPERATIVE BUT REQUEST SWITCHES WORK This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB13-097g
Service Bulletin/Repair Instructions
ALL MODEL YEAR 2012 AND NEWER NISSAN VEHICLES; EVAP LEAK DTC P0442, P0455, P0456 INFORMATION This bulletin does NOT apply to LEAF vehicles and Titan XD vehicles with V8 diesel engine. This bulletin has been amended. See Amendment History on the last page. Please discard previous versions of this bulletin.
NTB15-049r
Service Bulletin/Repair Instructions
TELEMATICS SERVICE INFORMATION This bulletin applies only to vehicles equipped with a Telematics Communication Unit (TCU). This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB17-082b
Service Bulletin/Repair Instructions
NISSAN; DTC P0456 CAUSED BY EVAP LEAK AT VENT CONTROL VALVE O-RING This bulletin does NOT apply to LEAF vehicles and Titan XD vehicles with V8 diesel engine. This bulletin has been amended. See Amendment History on the last page. Please discard previous versions of this bulletin.
NTB19-008
Service Bulletin/Repair Instructions
NISSAN; DIAGNOSIS INFORMATION FOR DTC P161D SERVICE INFORMATION When key registration is unsuccessful after BCM replacement, P161D (Immobilizer) will set when the ignition is turned on. Possible causes - Improper key registration - Defective BCM (Vehicles with Intelligent Key only) - EPS control unit (Vehicles with mechanical key only) - Intelligent Key unit (Vehicles with mechanical key only) Trouble Diagnosis NOTE: If DTC B2196-52 is stored with P161D, perform the diagnosis procedure for DTC B2196-52 first. - Before replacing the BCM, confirm that the keys were programmed correctly by ensuring the vehicle will start and that the lock/unlock buttons function normally. - If any keys do not function normally, re-register all of the keys. - After re-registering all of the keys, reconfirm each key's function. - If OK, erase the code to complete the repair. - If NG, diagnose the Key, BCM and/or EPS control unit per the ESM.
NTB19-009
Service Bulletin/Repair Instructions
2017-2019 ROGUE, ROGUE HYBRID AND ROGUE SPORT; CHASSIS CONTROL UNIT AND ADAS CONTROL UNIT 2 IDENTIFICATION SERVICE INFORMATION The CONTROLLER ASSY-IDM (Chassis Control Unit) and the CONTROLLER ASSYWARNING SPEAKER (ADAS Control Unit 2) may be incorrectly identified while diagnosing for related issues. The Chassis Control Unit and the ADAS Control Unit 2: - Cases, externally, appear identical. - Are located behind the glove box, in the same area. - Harness connectors are the same, and can be connected to the wrong component. NOTE: See Figure 1 for the correct locations of the Chassis Control Unit and the ADAS Control Unit 2. - Can be identified by their location (shown in Figure 1) and confirmed by the part number on the contorol unit?s label.
NPSB18-443 AEB U
Service Bulletin/Repair Instructions
2017-2018 Rogue and Rogue Sport Automatic Emergency Braking (AEB) Update Notification Letter Nissan is conducting an important Customer Service Initiative to increase awareness of an available update for the Automatic Emergency Braking (AEB) system on certain Model Year 2017-18 Rogue (T32), Rogue Sport (J11), and Rogue Hybrid (T32) vehicles. In rare instances and unique roadway environments such as certain types of railroad crossings and metal overpasses, the AEB system in some vehicles may activate braking when not needed. The driver can always override the AEB system by pressing the accelerator. To help enhance system performance for the customers that have experienced this issue, Nissan developed a special AEB system update that is available to owners at no cost for parts and labor during the duration of the Basic Coverage under their New Vehicle Limited Warranty (3 years/36,000 miles, whichever comes first). THIS CUSTOMER SERVICE INITIATIVE IS IMPLEMENTED TO MAKE CUSTOMERS AWARE OF AN AVAILABLE UPDATE. THIS INITIATIVE IS NOT A WARRANTY, AN EXTENSION OF THE NEW VEHICLE LIMITED WARRANTY, OR AN IMPLIED OR GENERAL WARRANTY, AND IS NOT CONNECTED TO ANY SALE OF THE VEHICLE.
NTB19-001
Service Bulletin/Repair Instructions
CHASSIS CONTROL MODULE DTC INFORMATION SERVICE INFORMATION If one or more of the following Chassis Control DTCs are stored: - C1BA0-00 ? (CHASSIS CONTROL BRAKE SYSTEM) - C1B92-00 ? (BRAKE CONTROL SYSTEM) - C1B93-00 ? (ENGINE/HEV SYSTEM) - C1B94-00 ? (TRANSMISSION SYSTEM) And One or more additional DTCs, other than those above, are also stored in a control unit other than the Chassis Control Module. - Perform the diagnostic/repair procedures for the additional DTCs of the other control unit FIRST. - Refer to the Electronic Service Manual (ESM) for DTC specific diagnostic information. Do not replace the CHASSIS CONTROL MODULE (CONTROLLER ASSY-IDM) if additional DTCs are present.
NTB18-084
Service Bulletin/Repair Instructions
2017-2018 ROGUE SPORT; REDUCED POWER DUE TO SNOW INGESTION IF YOU CONFIRM - An Applied Vehicle experiences reduced power during extremely heavy snow fall, And - Snow is found inside the air cleaner case. NOTE: The MIL may be ON with DTC P0101 (MAF SEN/CIRCUIT B1) stored. ACTION 1. Remove the front grille spacer. 2. Install foam blocks listed in the Parts Information. 3. Install the new front grille spacer.
NTB18-083
Service Bulletin/Repair Instructions
2014 - 2019 ROGUE; SQUEAK/CREAK NOISE FROM FRONT SUSPENSION BOUND BUMPER DRIVING OVER BUMPS IF YOU CONFIRM Using the flow chart on page 2, a squeak/creak noise is heard coming from the left or right front suspension bound bumper when driving over speed bumps or similar road surfaces. NOTE: This squeak/creak noise, if it should occur, is more noticeable in cold weather. ACTION Replace the front suspension bound bumper, only on the side that is making noise. - Refer to the appropriate Electronic Service Manual (ESM) for replacement information. SUSPENSION > FRONT SUSPENSION > REMOVAL AND INSTALLATION > FRONT COIL SPRING AND STRUT > Removal and Installation. - Pages 4 - 6 in this bulletin contain helpful information to perform this procedure. - Make sure to replace the one-time-use nuts listed in the PARTS INFORMATION. - Check the front wheel alignment; adjust to factory specifications as needed. NOTE: DO NOT apply lubricant to the bound bumper to resolve this issue.
NTB18-033a
Service Bulletin/Repair Instructions
2014 ? 2019 ROGUE; ACCELERATOR PEDAL VIBRATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB10-029e
Service Bulletin/Repair Instructions
NISSAN; VIBRATION AND/OR NOISE WHEN MAKING LOW SPEED TURNS This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB17-057b
Service Bulletin/Repair Instructions
2015-2019 ROGUE AND 2017-2019 ROGUE SPORT; DISTANCE TO EMPTY DOES NOT RESET This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB12-103f
Service Bulletin/Repair Instructions
CVT / TCM CALIBRATION DATA ?WRITE? PROCEDURE This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB18-077
Service Bulletin/Repair Instructions
MIL ON WITH DTC P0776, P1715 AND MAY HAVE HESITATION AND/OR LACK OF POWER This bulletin applies only to vehicles equipped with a CVT (Continuously Variable Transmission). IF YOU CONFIRM The MIL is ON with DTC P0776 (PC SOLENOID B ? Pressure Control Solenoid ?B? Performance/Stuck OFF) stored. NOTE: - If P0744, P0746, P0841, P0965, P2813, or P17F0 are stored this bulletin does not apply. Refer to ASIST for diagnostic assistance. - With this incident, if it should occur, P1715 (INPUT SPEED SENSOR) may be stored with DTC P0776. The vehicle may also hesitate and/or have reduced power. ACTION 1. Refer to the Repair Flow Chart on page 2 for mechanical CVT repair. 2. If needed, reprogram the TCM. - Refer to step 30 in the TCM Reprogram section (page 21) of the SERVICE PROCEDURE to confirm if reprogramming is needed. 3. Perform Additional Service (page 19).
NTB18-055a
Service Bulletin/Repair Instructions
CVT FLUID LEVEL QUICK CHECK GAUGE This bulletin applies only to vehicles equipped with a CVT (Continuously Variable Transmission). This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB18-071
Service Bulletin/Repair Instructions
SECURITY ALARM SOUNDS AFTER USING MECHANICAL KEY TO UNLOCK DRIVER DOOR SERVICE INFORMATION Applied Vehicles listed above are no longer equipped with a door unlock sensor and/or Body Control Module (BCM) software to provide support for the door unlock sensor. Normal Functionality For Vehicles Built Without Door Unlock Sensor And/Or BCM Software To Support Door Unlock Sensor For Applied Vehicles built after the Applied Dates listed on page 1, using the mechanical key on the driver door will operate differently than vehicles built before the Applied Dates. For these later models, the BCM will not recognize operation of the mechanical key. If a mechanical key is used to lock the driver door: - The security system will not set. If the vehicle is broken into, the alarm will not sound. - Only the driver door will be locked. Other doors will not lock using the mechanical key. If a mechanical key is used to unlock the driver door: - Only the driver door will be unlocked. Other doors will not be unlocked. - If the security system is set, when the door is opened the alarm will sound. NOTE: Using the Unlock button on the Intelligent Key, pushing the request switch on the driver or passenger door with the Intelligent Key in range, or using the Intelligent Key to start the vehicle will silence the alarm. The mechanical key will not operate the power windows.
P8327 Radar Sens
Service Bulletin/Repair Instructions
Radar and/or Advanced Drive Assist System (ADAS) Reprogram ***** Quality Action Summary ***** Nissan is conducting a quality action to reprogram the Laser Radar and Advanced Drive Assist System (ADAS) software the on specific MY2018 Rogue (T32) and MY2018 Rogue Sport (J11) vehicles built in the Kyushu manufacturing plant. These vehicles are either currently in dealer inventory or assigned and in transit to the dealer. The software update is designed to help improve the performance of Automatic Emergency Braking (AEB) and Intelligent Forward Collision Warning (I-FCW) systems in the affected vehicles. ***** What Dealers Should Do ***** 1. Verify if vehicles are affected by this quality action using Service Comm or National Service History ? Open Campaign I.D. P8327. - New vehicles in dealer inventory can also be identified using DBS (Sales-> Vehicle Inventory, and filter by Open Campaign). - Refer to NPSB 15-460 for additional information - Please continue to check newly arriving inventory for campaign applicability. 2. Use the attached procedure to reprogram the Laser Radar and/or Advanced Drive Assist System (ADAS) control unit software. 3. Dealers are requested to remedy any affected vehicle in dealer new inventory prior to sale to ensure customer satisfaction. Thank you for your prompt attention to this matter. NISSAN NORTH AMERICA, INC. Aftersales DIVISION
NTB15-077b
Service Bulletin/Repair Instructions
NISSAN; SIGNAL TECH-II INTELLIGENT KEY BATTERY TEST AND SIGNAL CHECK This bulletin has been amended. See Amendment History on the last page. Please discard previous versions of this bulletin.
NTB17-111c
Service Bulletin/Repair Instructions
NISSANCONNECT OVER THE AIR SOFTWARE UPDATE This bulletin has been amended. The APPLIED VEHICLES section has been revised. No other changes have been made. Please discard all previous versions of this bulletin.
NTB10-029d
Service Bulletin/Repair Instructions
NISSAN; VIBRATION AND/OR NOISE WHEN MAKING LOW SPEED TURNS This bulletin applies only to vehicles equipped with AWD (All-Wheel Drive) or 4WD (4-Wheel Drive). This bulletin has been amended. The APPLIED VEHICLES and PARTS INFORMATION sections have been revised. No other changes have been made. Please discard all previous versions of this bulletin.
NTB17-113a
Service Bulletin/Repair Instructions
2017-2018 ROGUE SPORT; WHEN COLD LONG CRANK TIME, ENGINE TURNS OFF, HESITATION, ROUGH IDLE, OR MISFIRE This bulletin has been amended. The Title and APPLIED VEHICLES have been revised. Part numbers have been added to Table A on page 5. No other changes have been made. Discard all previous versions of this bulletin.
PC651
Service Bulletin/Repair Instructions
CAMPAIGN BULLETIN Rear Brake Hose Bracket *****Dealer Announcement***** Nissan is conducting a quality action to inspect 1,120 specific 2018.5 Rogue and Rogue Hybrid vehicles identified in Service Comm, and if necessary, tighten the rear brake hose bracket fasteners to the specification. Affected vehicles are not subject to stop sale and are either currently in dealer inventory or assigned and in transit to the dealer. Nissan requests dealers to complete this inspection and, if necessary, repair prior to sale to ensure customer satisfaction. *****What Dealers Should Do***** PLEASE FOLLOW THE ATTACHED REPAIR INSTRUCTIONS: 1. Verify if vehicles currently in new dealer inventory are affected by this service action using Service Comm I.D. PC651 - New vehicles in dealer inventory can also be identified using DCS (Sales-> Vehicle Inventory, and filter by Open Campaign). - Refer to NPSB 15-460 for additional information - Please continue to check newly arriving inventory for campaign applicability. 2. Use the attached procedure to inspect the vehicle. - Do not file a claim if the bracket is loose (moveable by hand) or the bolt(s) are missing. Additional Steps are required for a Loose Bracket or Missing bolts. - Email the following information to: nnafqasupport@nissan-usa.com - E-mail subject line: PC651 Rear Brake Hose Bracket - Attach clear pictures of bracket - Dealer Name: - Dealer Code: - Dealer Address: - VIN: - Contact Person Name: - Contact Person Phone Number: - Continue to HOLD the vehicle.
NTB15-049q
Service Bulletin/Repair Instructions
TELEMATICS SERVICE INFORMATION This bulletin applies only to vehicles equipped with a Telematics Communication Unit (TCU). This bulletin has been amended to add a Required Actions by Model and Year table on page 2, a Check OFF Sheet on page 21 and to reorganize the information throughout. It is necessary for you to read this revised procedure to properly perform this Service Information. Please discard previous versions of this bulletin.
NTB17-111b
Service Bulletin/Repair Instructions
2018 ROGUE; NISSANCONNECT OVER THE AIR SOFTWARE UPDATE This bulletin has been amended. Steps to check for additional software updates have been added. Please discard all previous versions of this bulletin.
NTB17-097a
Service Bulletin/Repair Instructions
2016-2018 ROGUE AND 2017-2018 ROGUE SPORT; WHISTLE NOISE TRANSMITTED TO CALL RECIPIENT WHEN USING BLUETOOTH HANDS-FREE PHONE SYSTEM This bulletin has been amended. Changes have been made throughout. It is necessary for you to read this revised procedure to properly perform this action. Please discard all previous versions of this bulletin.
PC637
Service Bulletin/Repair Instructions
Radar and/or Advanced Drive Assist System (ADAS) Reprogram ***** Quality Action Summary ***** Nissan is conducting a quality action to reprogram the Laser Radar and Advanced Drive Assist System (ADAS) software the on specific MY2018 Rogue (T32) vehicles built in the Smyrna, TN manufacturing plant. These vehicles are either currently in dealer inventory or assigned and in transit to the dealer. The software update is designed to help improve the performance of Automatic Emergency Braking (AEB), Forward Emergency Braking (FEB), and Forward Collision Warning (FCW) systems in the affected vehicles. ***** What Dealers Should Do ***** 1. Verify if vehicles are affected by this quality action using Service Comm or National Service History ? Open Campaign I.D. PC637. - New vehicles in dealer inventory can also be identified using DBS (Sales-> Vehicle Inventory, and filter by Open Campaign). - Refer to NPSB 15-460 for additional information - Please continue to check newly arriving inventory for campaignapplicability. 2. Use the attached procedure to reprogram the Laser Radar and/or Advanced Drive Assist System (ADAS) control unit software. 3. Dealers are requested to remedy any affected vehicle in dealer new inventory prior to sale to ensure customer satisfaction. Thank you for your prompt attention to this matter.
NTB13-077d
Service Bulletin/Repair Instructions
CVT FLUID LEVEL CHECK SERVICE INFORMATION This bulletin applies only to vehicles equipped with a Continuously Variable Transmission (CVT). This bulletin has been amended. The APPLIED VEHICLES and SERVICE INFORMATION sections have been revised. No other changes have been made. Please discard all previous versions of this bulletin.
NTB15-049p
Service Bulletin/Repair Instructions
TELEMATICS SERVICE INFORMATION This bulletin only applies to vehicles equipped with a Telematics Communication Unit (TCU). This bulletin has been amended. Changes have been made to page 10 for 2018 Armada. Please discard previous versions of this bulletin.
NTB18-055
Service Bulletin/Repair Instructions
CVT FLUID LEVEL QUICK CHECK GAUGE This bulletin applies only to vehicles equipped with a Continuously Variable Transmission (CVT). SERVICE INFORMATION Special tool CVT8 Oil Level Quick Check Gauge (J-51155) is now available. Each dealer has been shipped one of these tools. Additional tools can be obtained from Tech?Mate at 1-800-662-2001. Refer to the SERVICE PROCEDURE on the next page to determine how to perform a CVT fluid quick level check.
NTB18-017b
Service Bulletin/Repair Instructions
NISSAN; SERVICE INFORMATION FOR DTCS B2EF0 AND B130C This bulletin only applies to vehicles equipped with a Telematics Communication Unit (TCU). This bulletin has been amended. APPLIED VEHICLES has been updated. On page 2, the procedural steps under DTC B130C have been revised. Discard all previous versions of this bulletin.
NTB18-041a
Service Bulletin/Repair Instructions
2017-2018 ROGUE, ROGUE HYBRID AND ROGUE SPORT; UNEXPECTED OPERATION OF AEB, FEB OR FCW This bulletin has been amended. Changes have been made throughout. It is necessary for you to read this revised procedure to properly perform this action. Please discard all previous versions of this bulletin.
NTB18-047
Service Bulletin/Repair Instructions
2018 ROGUE SPORT; MIL ON WITH A/F RATIO SENSOR DTC(S) IF YOU CONFIRM The MIL is ON with one or more of the following Air/Fuel (A/F) Sensor DTCs stored: - P015A - A/F SENSOR1 (B1) (O2 sensor delayed response - rich to lean bank 1 sensor 1) - P015B - A/F SENSOR1 (B1) (O2 sensor delayed response - lean to rich bank 1 sensor 1) and There are no drivability issues. ACTION 1. Refer to step 6 in the SERVICE PROCEDURE to confirm this bulletin applies to the vehicle you are working on. If this bulletin applies: 2. Reprogram the ECM.
NTB18-031b
Service Bulletin/Repair Instructions
2016-2018 NISSAN CONNECT NAVIGATION SYSTEM SOFTWARE UPDATE TO RESOLVE SEVERAL ISSUES This bulletin has been amended. The IF YOU CONFIRM section and software number has changed. No other changes have been made. Please discard previous versions of this bulletin.
NTB17-111a
Service Bulletin/Repair Instructions
2018 ROGUE; NISSANCONNECT OVER THE AIR SOFTWARE UPDATE This bulletin has been amended. Changes have been made throughout. It is necessary for you to read this revised information to properly perform software update. Please discard all previous versions of this bulletin.
NTB18-041
Service Bulletin/Repair Instructions
2018 ROGUE, ROGUE HYBRID AND ROGUE SPORT; UNEXPECTED OPERATION OF AEB, FEB OR FCW IF YOU CONFIRM The following system(s) operate unexpectedly or the customer reports unexpected operation: - AEB (Automatic Emergency Braking) - FEB (Forward Emergency Braking) - FCW (Forward Collision Warning) ACTION Refer to the Repair Overview on page 2.
NTB18-031a
Service Bulletin/Repair Instructions
2016-2018 NISSAN CONNECT NAVIGATION SYSTEM SOFTWARE UPDATE TO RESOLVE SEVERAL ISSUES This bulletin applies only to vehicles equipped with navigation system. This bulletin has been amended to correct Bosch contact information on page 2. No other changes have been made. Please discard previous versions of this bulletin.
18MY Rogue Adden
Service Bulletin/Repair Instructions
Owner's Manual Supplement The information contained within this supplement updates the following information in the 2018 NISSAN Rogue Owner?s Manual: ? ?Starting the vehicle? in the ?Starting and driving? section of the Owner?s Manual ? ?AUTOMATIC BRAKE HOLD (if so equipped)? and ?HOW TO ACTIVATE/DEACTIVATE THE AUTOMATIC BRAKE HOLD FUNCTION? in the ?Starting and driving? section of the Owner?s Manual ? ?INTELLIGENT LANE INTERVENTION (I-LI) (if so equipped)? in the ?Starting and driving? section of the Owner?s Manual ? ?OPERATING PROPILOTTM ASSIST? in the ?Starting and driving? section of the Owner?s Manual
NTB18-031
Service Bulletin/Repair Instructions
2016-2018 NISSAN CONNECT NAVIGATION SYSTEM SOFTWARE UPDATE TO RESOLVE SEVERAL ISSUES This bulletin applies only to vehicles equipped with navigation system. IF YOU CONFIRM One or more of the following is occurring: - The navigation unit intermittently reboots: - At random or while listening to SXM or on a Bluetooth hands-free phone call. - Loud booming noise from speakers while on a Bluetooth hands-free call. - Navigation unit screen illumination does not change at night as designed. - AM/FM signal strength issues. - A status message ?Voice Recognition is initializing, please wait? is displayed when pressing the voice recognition button 2-3 minutes after the ignition is first turned ON. NOTE: If the message is displayed within the first 2-3 minutes this is normal. The voice recognition is loading phonebook contacts into its system. AND - The Software version has been confirmed as ?needs update? (refer to page 4). ACTION - Perform the SERVICE PROCEDURE starting on page 3 and reprogram the Navigation system with USB memory stick shown below.
PC626
Service Bulletin/Repair Instructions
ProPILOT Assist Owner?s Manual Update Voluntary Service Campaign ***** Campaign Summary***** Nissan is providing owners of approximately 1,377 MY2018 Nissan Rogue (T32) vehicles with an Owner?s Manual addendum booklet. The addendum booklet corrects the description of how the customer should activate the Intelligent Lane Intervention (ILI) function on vehicles equipped with ProPILOT Assist. Customers will be asked to place the addendum booklet inside the Owner?s Manual for future reference. A copy of the addendum booklet is included with this announcement. ***** What Dealers Should Do ***** 1. Verify if new vehicles in their inventory are affected by this Voluntary Service Campaign using Service Comm or DBS National Service History ? Open Campaign I.D. PC626. - New vehicles in dealer inventory can also be identified using DBS (Sales-> Vehicle Inventory, and filter by Open Campaign). - Refer to NPSB 15-460 for additional information - SERV COMM will only be active for vehicles in new vehicle dealer inventory 2. If a dealer receives and addendum booklet for a vehicle they have retailed, currently have in their pre-owned inventory, or placed into NRC Service, the dealer should either forward the Owner?s Manual addendum to the current owner or add the addendum booklet to the Owner?s Manual of any vehicles they currently control. 3. Customers receiving this addendum booklet have been advised to insert this booklet into their Owner?s Manual.
NTB03-074m
Service Bulletin/Repair Instructions
FOG LAMP AND/OR HEADLAMP FOGGING This bulletin has been amended to add Fog Lamps and modify one step in the flow chart on page 3. No other changes have been made. Please discard previous versions of this bulletin.
NTB16-115a
Service Bulletin/Repair Instructions
REVISED WHEEL ALIGNMENT SPECIFICATIONS This bulletin has been amended. The APPLIED VEHICLES were updated with new models and model years. No other changes have been made. Discard all previous versions of this bulletin.
NTB18-009a
Service Bulletin/Repair Instructions
2017 ? 2018 ROGUE SPORT; FRONT WHEEL ALIGNMENT TOTAL TOE SPECIFICATION This bulletin has been superseded to NTB16-115. Discard previous versions of this bulletin.
NTB18-033
Service Bulletin/Repair Instructions
2014 - 2018 ROGUE; ACCELERATOR PEDAL VIBRATION IF YOU CONFIRM A vibration from the accelerator pedal between 1600 - 2000 RPM. ACTION Install the new brake booster vacuum tube and hose listed in the PARTS INFORMATION section of this bulletin.
NTB16-018c
Service Bulletin/Repair Instructions
MIL ON WITH P0603 STORED FOR ECM BACK UP CIRCUIT This bulletin does NOT apply to Titan equipped with Cummins V8 Diesel engine. This bulletin has been amended to add a NOTE in the Applied Vehicles. No other changes have been made. Please discard previous versions of this bulletin.
NTB13-107b
Service Bulletin/Repair Instructions
INTELLIGENT KEY NOT DETECTED / ENGINE WILL NOT START This bulletin has been amended to update the Applied Vehicles. No other changes were made. Please discard previous versions of this bulletin.
NTB18-017a
Service Bulletin/Repair Instructions
NISSAN; SERVICE INFORMATION FOR DTCS B2EF0 AND B130C This bulletin applies only to vehicles equipped with Telematics. This bulletin has been amended. APPLIED VEHICLES was updated and a DTC listed in the SERVICE INFORMATION was corrected. No other changes have been made. Discard all previous versions of this bulletin.
NTB11-044c
Service Bulletin/Repair Instructions
WHEEL BALANCING SERVICE INFORMATION This bulletin has been amended. The publication date has been revised to include the latest models and model years. No other changes have been made. Please discard previous versions of this bulletin.
NTB18-023
Service Bulletin/Repair Instructions
NISSAN; MICROPHONE DOES NOT WORK This bulletin applies only to vehicles equipped with Telematics. IF YOU CONFIRM The microphone of an applied vehicle does not work. - The person receiving your call through Bluetooth® cannot hear you. And Voice Recognition does not respond to any commands. NOTE: DTCs U1A01 and/or U1A02 may be found stored. ACTION 1. Confirm TCU reprogramming will resolve the issue. - Refer to ?Issue Confirmation? on page 2. 2. If confirmed, reprogram the TCU.
NTB18-019
Service Bulletin/Repair Instructions
2013-2018 ALTIMA AND 2014-2018 ROGUE; ENGINE SUPPORT TOOLS SERVICE INFORMATION A new Engine Support Tool and Engine Support Bracket are now available to allow the CVT to be removed from the Applied Vehicles without having to remove the engine. The procedures in this bulletin are different than those that are currently in the Electronic Service Manual (ESM), which will be updated with this information at a later date. Please refer to the vehicle specific service procedure to use these new tools: Altima Page 2 Rogue AWD Page 11 Rogue FWD Page 24
PC601 2016-18
Service Bulletin/Repair Instructions
Left Hand Engine Mounting Insulator Voluntary Service Campaign UPDATE March 2, 2018 Please discard earlier versions of this bulletin The announcement from January 18, 2018 has been revised to include: - Retailed vehicles affected by this campaign are now include in this announcement - Campaign repair bulletin, NTB18-002 has been revised to include the location of a repair video, which is now available in Virtual Academy under the Tech Training Garage Videos tab. See video #554: ?2016-17 Rogue Left Hand Engine Mount Insulator Campaign?. - Nissan has developed a parts shipment plan for use on retailed units. Parts (2 per dealer) will begin to arrive at dealerships on Monday, March 5, 2018. o Dealers may order parts via normal ordering process beginning March 12, 2018, if additional parts are needed.
NTB18-017
Service Bulletin/Repair Instructions
NISSAN; SERVICE INFORMATION FOR DTCS B2EF0 AND B130C This bulletin applies only to vehicles equipped with Telematics. SERVICE INFORMATION Diagnostic information in the Electronic Service Manuals (ESM) for the following DTCs may be missing or incorrect: -B2EF0 ? INTERNAL BATTERY (CIRC VOLT BELOW THRESHOLD) -B130C ? TCU (Telematics Control Unit) PAIRING ERROR If one of these DTCs is stored, follow the steps listed below along with the Electronic Service Manual (ESM) to compete the required repairs. DTC B2FE0 ? INTERNAL BATTERY (CIRC VOLT BELOW THRESHOLD): 1. Start the engine and let it idle for 30 minutes (to allow charging of the TCU internal battery). -2018 LEAF only: Put the vehicle in Ready to Drive mode (depress the brake pedal and depress the power [?ignition?] switch) for 30 minutes. 2. Verify the DTC can be erased. 3. If the DTC will not erase, replace the TCU. DTC B130C: 1. Collect all keys, and then re-register them to the vehicle. 2. Verify the DTC can be erased. 3. If the DTC will not erase, replace the TCU. NOTE: The related Electronic Service Manuals (ESM) will be updated at a later date. CLAIMS INFORMATION Refer to the current Nissan Warranty Flat Rate Manual and submit a claim for the repairs performed.
NPSB17-083
Service Bulletin/Repair Instructions
Service Department Wi-Fi Requirement - Password Protected Beginning with the 2018 MY Rogue, the NissanConnect service has the ability to update its system's firmware through a Wi-Fi connection. A Wi-Fi connection can be made to the vehicle for updating NAVI map data and system software, or using online services, such as Online Search or Premium Traffic. Workshop Wi-Fi network must be configured as WPA2 password-protected to allow connection with the 2018 MY Rogue and future equipped models. For connecting to these vehicles, please confirm with your dealer network administrator to ensure your Wi-Fi is arranged as password-protected. If you need to add password-protected, please update the login credentials on any other workshop equipment connected to the Wi-Fi network. As an example, listed below is instructions on connecting to the Wi-Fi network through the 2018 MY Rogue screen display. For additional information on this new Wi-Fi connectivity feature, refer to the vehicle NissanConnect Owner's Manual.
PC612 2018
Service Bulletin/Repair Instructions
A-IVI Software Reprogram ***** Quality Action Summary ***** Nissan is conducting a quality action on new vehicle inventory to reprogram the Alliance-In Vehicle Infotainment (A-IVI) software on specific MY2018 Rogue (T32) vehicles identified in SERVICE COMM or DBS National Service History ? Open Campaigns. These vehicles are either currently in dealer inventory or assigned and in transit to the dealer. The software update will correct a potential issue with the NissanConnect system displaying a blank screen after the vehicle is turned on. ***** What Dealers Should Do ***** 1. Verify if vehicles currently in dealer inventory are affected by using Service Comm or DBS National Service History ? Open Campaign I.D. PC612. - New vehicles in dealer inventory can also be identified using DBS (Sales-> Vehicle Inventory, and filter by Open Campaign). - Refer to NPSB 15-460 for additional information - Please continue to check newly arriving inventory for campaign applicability. 2. Use the attached procedure to reprogram the affected vehicles. - This procedure requires no tools and does not require a technician to perform - The vehicle must be in range of the service departments Wi-Fi network in order to download the software update - The person performing the update must know the service department?s password to the secure WPA2 Wi-Fi network - Refer to NPSB17-083 regarding service department Wi-Fi network requirements 3. Dealers are requested to remedy any affected vehicle in dealer new inventory to help ensure customer satisfaction. 4. The service department should submit the applicable warranty claim for the action performed so it can be closed on Service Comm and release the vehicle.
NTB15-049o
Service Bulletin/Repair Instructions
TELEMATICS SERVICE INFORMATION This bulletin applies only to vehicles equipped with a Telematics Communication Unit (TCU). This bulletin has been amended. Changes have been made throughout. It is necessary to read the revised procedure(s) in entirety to properly perform the action(s). Please discard previous versions of this bulletin.
NTB18-009
Service Bulletin/Repair Instructions
2017 ? 2018 ROGUE SPORT; FRONT WHEEL ALIGNMENT TOTAL TOE SPECIFICATION SERVICE INFORMATION Hunter brand alignment machines may have incorrect alignment specifications for ?total toe-in? on 2017-2018 Rogue Sport. - The correct specifications can be found in the Electronic Service Manual (ESM) SUSPENSION > FRONT SUSPENSION (see page 2). - Revised data is currently available for installation from Hunter. - Until the updated data is installed in your Hunter machine, please use the correct specifications on page 2, or in the Electronic Service Manual (ESM).
NTB18-008
Service Bulletin/Repair Instructions
ADAS SYSTEM DTC C1A03, C1A04, AND/OR C1B01 SERVICE INFORMATION This bulletin applies only to vehicles equipped with Automatic Emergency Braking (AEB) or Forward Emergency Braking (FEB). SERVICE INFORMATION If the following ICC/ADAS codes are stored, make sure to follow the diagnostic procedures in the Electronic Service Manual (ESM) before replacing any parts. C1A03 ? VEHICLE SPEED SENSOR -The diagnostic procedure in the ESM includes check and, if needed, repair for ABS DTCs before replacing ADAS components. -If repairs are performed for the ABS system; when compete, perform DTC Confirmation Procedure again before doing any additional repairs. C1A04 ? ABS/TCS/VDC SYSTEM -The diagnostic procedure in the ESM includes check and, if needed, repair for ABS DTCs before replacing ADAS components. -If repairs are performed for the ABS system; when compete, perform DTC Confirmation Procedure again before doing any additional repairs. C1B01 CAM AIMING INCMP -The diagnostic procedure in the ESM includes check and, if needed, repair for LANE CAMERA DTCs before replacing ADAS components. -LANE CAMERA DTC may require adjustment of the lane camera. -If repairs/adjustments are performed for the Lane Camera; when compete, perform DTC Confirmation Procedure again before doing any additional repairs.
NTB17-083a
Service Bulletin/Repair Instructions
MOTION ACTIVATED LIFTGATE STICKER This bulletin applies to vehicles equipped with a Motion Activated Liftgate. This bulletin has been amended to add 2018 Murano, update model years in the Applied Vehicles, and change the part number in the Parts Information. Please discard previous version of this bulletin.
NTB15-049n
Service Bulletin/Repair Instructions
TELEMATICS SERVICE INFORMATION This bulletin applies to vehicles equipped with a TCU (Telematics Communication Unit). This bulletin has been amended. A correction was made to the Service Procedure on page 23. No other changes were made. Please discard previous versions of this bulletin.
NTB17-057a
Service Bulletin/Repair Instructions
2015-2017 ROGUE AND 2017-2018 ROGUE SPORT; DISTANCE TO EMPTY DOES NOT RESET This bulletin has been amended. Changes have been made throughout. Please discard all previous versions of this bulletin.
NTB17-118
Service Bulletin/Repair Instructions
NISSAN; INTELLIGENT KEY IDENTIFICATION AND REGISTRATION TIPS This bulletin applies to vehicles equipped with Intelligent Key only. SERVICE INFORMATION When replacing or adding an Intelligent Key, it is very important to make sure the correct Intelligent Key is selected from the parts department. - A running change was made that will help identify the correct Intelligent Key. - Beginning in late 2017 and early 2018 the last five digits of the Intelligent Key part number is marked on the Intelligent Key under the mechanical key. - See page 2 for location images of this part number addition. NOTE: - A correct Intelligent Key may or may not have the last five digits of the part number as shown on page 2. - The above running change was applied as a ?help? to identify the correct Intelligent Key for a given vehicle, but the actual part number listed in the parts catalog did not change. - Make sure to use the electronic parts catalog (FAST) or equivalent to confirm the correct Intelligent Key for a given vehicle.
NTB17-119
Service Bulletin/Repair Instructions
2018 ROGUE; INTELLIGENT KEY REGISTRATION TIPS This bulletin applies to vehicles equipped with Intelligent Key only. SERVICE INFORMATION When replacing or adding an Intelligent Key of an Applied Vehicle: 1. ALWAYS initialize/register the original Intelligent Key(s) BEFORE attempting to initialize/register a new one. 2. Confirm the Intelligent Key is correct for the vehicle being worked on. - The last five digits of the Intelligent Key?s part number is printed on the back behind the mechanical key. If a ?new? Intelligent Key will not initialize/register, go to page 2 to determine if the ?new? Intelligent Key has been previously initialized/registered to another vehicle. NOTE: Once a new Intelligent Key has been initialized/registered to a vehicle, it can be reinitialized/reregistered as many times as needed to the same vehicle.
NTB15-049m
Service Bulletin/Repair Instructions
TELEMATICS SERVICE INFORMATION This bulletin applies to vehicles that are equipped with a wireless communication device called a Telematics Communication Unit (TCU). This bulletin has been amended. Changes have been made throughout. You must read the entire bulletin to understand all the changed information. Please discard previous versions of this bulletin.
NTB17-111
Service Bulletin/Repair Instructions
2018 ROGUE; NEXT GENERATION NISSANCONNECT OVER THE AIR UPDATE FEATURE SERVICE INFORMATION The next generation NissanConnect now has the ability to update its system?s software through a Wi-Fi connection. These updates can now be applied by the customer, using their home Wi-Fi network, without the vehicle having to return to the dealer. Updates allow the customer to take advantage of: - New features as they become available - Continuous quality and performance improvements In some cases the customer may not have access to a secured WiFi network and will need to return to the dealer to perform any available updates. The Service Procedure in this bulletin contains the instructions to perform updates via a Wi-Fi connection. IMPORTANT: - To update the software by Wi-Fi the vehicle must be within range and connected to a secure Wi-Fi network. - A password protected Wi-Fi network with WPA2 security is required to secure the update download. WARNING: During the update process, the vehicle should be kept in a well-ventilated area to avoid the exposure to Carbon Monoxide. Do not breathe exhaust gases; they contain colorless and odorless carbon monoxide. Carbon Monoxide is dangerous. It can cause unconsciousness or death. NOTE: When diagnosing a NissanConnect issue, always confirm that the latest available software is installed in the AV unit before starting a diagnosis.
NTB15-049L
Service Bulletin/Repair Instructions
TELEMATICS SERVICE INFORMATION This bulletin applies to vehicles equipped with a Telematics Communication Unit (TCU). This bulletin has been amended. Information for several 2018 models has been added. No other changes have been made. Please discard previous versions of this bulletin.
NTB11-044b
Service Bulletin/Repair Instructions
WHEEL BALANCING SERVICE INFORMATION This bulletin has been amended. The publication date has been revised to include the latest models and model years. No other changes have been made. Please discard previous versions of this bulletin.