Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
NTB09-131C
Service Bulletin/Repair Instructions
CERTIFICATION LABEL AND VIN PLATE REPLACEMENT SERVICE INFORMATION Because of collision damage or other vehicle repair, a replacement “Certification Label” or “VIN Plate/Label” may be needed. HINT: Certification Label = FMVSS (Federal Motor Vehicle Safety Standards) label. These items may be available from Nissan by request if certain criteria are met. This bulletin lists the criteria and provides an application form for such replacements. · The “VIN Plate/Label” (metal plate or vinyl label) is attached to the instrument panel or body on the driver side at the base of the windshield (see Figure 1). · The “Certification Label” (vinyl adhesive label) is located on the lower area of the driver side B-Pillar (see Figure 1).
NTB15-049CC
Service Bulletin/Repair Instructions
TELEMATICS SERVICE INFORMATION HINT: This bulletin applies to vehicles equipped with a 4G network compatible TCU. TCUs compatible with 3G network only are no longer supported. SERVICE INFORMATION The APPLIED VEHICLES that come equipped with a factory installed SOS switch, located near the overhead map lamp, also come equipped with a wireless communication device called a Telematics Communication Unit (TCU). With an active NissanConnect® Services subscription, the TCU communicates with the NissanConnect® Services Data Center to provide various security and convenience services. This bulletin contains important service procedures that must be performed properly in order to set-up and maintain the telematics system for the APPLIED VEHICLES. · A table has been provided on the next page that lists the steps required to successfully configure a TCU after it has been replaced. · A CHECK-OFF SHEET has been provided on page 20 to print and check off steps as they are performed. Staple the completed CHECK-OFF SHEET to the repair order.
NTB19-033G
Service Bulletin/Repair Instructions
INTELLIGENT CRUISE CONTROL INOPERATIVE AND AEB/FEB WARNING LIGHT ON OR RADAR OBSTRUCTION MESSAGE DISPLAYED WITH DTC C1A16 OR C2582 IF YOU CONFIRM IMPORTANT: The purpose of ACTION (on the next page) is to give you a quick idea of the work you will be performing. You MUST closely follow the entire SERVICE PROCEDURE as it contains information that is essential to successfully completing this repair. Nissan Bulletins are intended for use by qualified technicians, not 'do-it-yourselfers'. Qualified technicians are properly trained individuals who have the equipment, tools, safety instruction, and know-how to do a job properly and safely. NOTE: If you believe that a described condition may apply to a particular vehicle, DO NOT assume that it does. See your Nissan dealer to determine if this applies to your vehicle. The customer states that the ICC stopped working while driving, OR The customer states that the AEB/FEB warning light is ON, or turned ON, while driving (Figure 1), OR The message “Unavailable Front Radar Obstruction” or “Forward Driving Aids Temporarily Disabled Front Sensor Blocked See Owner's Manual” has displayed while driving (Figure 2). AND DTC C1A16, C1A16-97, C2582, or C2582-97 is the ONLY DTC stored. Figure 1 Figure 2 This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin. Forward Driving Aids Temporarily Disabled Front Sensor Blocked See Owner’s Manual
NTB19-042F
Service Bulletin/Repair Instructions
AUTOMATIC EMERGENCY BRAKING WARNING LIGHT BLINKING APPLIED SYSTEMS: Vehicles equipped with a lane camera (see Figure 1) SERVICE INFORMATION If the Automatic Emergency Braking (AEB) warning light or is blinking (but not illuminated steadily) or the customer states it is blinking, and there are no related DTCs, inspect the windshield. A blinking AEB warning light may occur under the following conditions: When contamination or foreign material adhere to the lane camera viewing window on the windshield. When driving while it is snowing or when frost forms on the lane camera viewing window on the windshield. When the lane camera viewing window on the windshield is temporarily fogged up. Figure 1 Nissan Bulletins are intended for use by qualified technicians, not 'do-it-yourselfers'. Qualified technicians are properly trained individuals who have the equipment, tools, safety instruction, and know-how to do a job properly and safely. NOTE: If you believe that a described condition may apply to a particular vehicle, DO NOT assume that it does. See your Nissan dealer to determine if this applies to your vehicle. HINT: o Refer to the applicable ESM for diagnosis if DTCs are present in the Laser/Radar, ICC/ADAS, or Lane Camera systems. o For further information: Refer to the following pages. Use the search keyword “blinking” in the ESM.
NTB20-066C
Service Bulletin/Repair Instructions
LANE CAMERA AIMING VEHICLE REFERENCE VALUES NOT IN ESM SERVICE INFORMATION If the lane camera requires aiming, the values in Table A on page 4 must be used. For all other models/model years, consult the Electronic Service Manual (ESM).
NTB19-071D
Service Bulletin/Repair Instructions
DTC B00A0-00 STORED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin. IF YOU CONFIRM DTC B00A0-00 (OCCUPANT DETECTION SENSOR UNIT) is stored, AND OCS zero point reset cannot be performed, (continued on the next page)
NTB12-103I
Service Bulletin/Repair Instructions
CVT/TCM CALIBRATION DATA “WRITE” PROCEDURE This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB10-066C
Service Bulletin/Repair Instructions
CAN COMMUNICATION CODES – DIAGNOSTIC TIPS AND GUIDELINES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB13-027D
Service Bulletin/Repair Instructions
CAN COMMUNICATION – NETWORK DIAGNOSTIC FLOW CHART This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB13-107G
Service Bulletin/Repair Instructions
VEHICLE KEY NOT DETECTED / AUTHENTICATED, ENGINE WILL NOT START This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB21-106B
Service Bulletin/Repair Instructions
DTC C1A17-49 OR C2580-49 STORED IN LASER/RADAR This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB09-081K
Service Bulletin/Repair Instructions
WINDSHIELD CRACKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB13-028I
Service Bulletin/Repair Instructions
REMOVING FOREIGN MATERIAL FROM THE WINDOW GLASS This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB17-019H
Service Bulletin/Repair Instructions
WINDOW GLASS WARRANTY INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB19-042E
Service Bulletin/Repair Instructions
AUTOMATIC EMERGENCY BRAKING WARNING LIGHT BLINKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB23-018G
Service Bulletin/Repair Instructions
SOFTWARE UPDATE FOR INFOTAINMENT ISSUES This bulletin is no longer active. To access infotainment software updates via the Infotainment Software Update Utility: Select SPECIALTY TOOLS, and then select Infotainment Software Updates on the left side of ASIST. Please discard previous versions of NTB23-018.
NTB23-018F
Service Bulletin/Repair Instructions
SOFTWARE UPDATE FOR INFOTAINMENT ISSUES This bulletin is no longer active. To access infotainment software updates via the Infotainment Software Update Utility: Select SPECIALTY TOOLS, and then select Infotainment Software Updates on the left side of ASIST. HINT: Initially, the Infotainment Software Update Utility will be available only on the CONSULT PC version of ASIST. The Utility will be added to ASIST WEB at a later date. Please discard previous versions of NTB23-018.
NTB15-049AA
Service Bulletin/Repair Instructions
TELEMATICS SERVICE INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB17-003F
Service Bulletin/Repair Instructions
FLUID LEAK CAUSED BY TRANSFER ASSEMBLY RIGHT SIDE DRIVE SHAFT OIL SEAL This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB21-094B
Service Bulletin/Repair Instructions
TRANSFER ASSEMBLY SEAL REPLACEMENT FOR AWD FRONT DRIVE SHAFT REMOVAL This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB08-097L
Service Bulletin/Repair Instructions
DIAGNOSIS OF VEHICLE PULL (DRIFT) AND/OR STEERING WHEEL OFF-CENTER This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB23-067
Service Bulletin/Repair Instructions
2014-2020 ROGUE & 2017-2022 ROGUE SPORT; REPLACEMENT JACKKNIFE (FLIP STYLE) KEYS SERVICE INFORMATION For the APPLIED VEHICLES listed above: ï· If the jackknife key is replaced with 80560-4BA1E, the new part provided will no longer be equipped with a key blade. ï· New service parts will have a keyless entry remote with a separate mechanical key. ï· Each vehicle can have a maximum of four (4) keys registered to the BCM. Each service part contains one (1) key and one (1) remote and will use two (2) of the available slots. ï· Follow the SERVICE PROCEDURE starting on page 2 to register the new mechanical key and remote.
NTB23-018E
Service Bulletin/Repair Instructions
SOFTWARE UPDATE FOR INFOTAINMENT ISSUES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB23-018D
Service Bulletin/Repair Instructions
SOFTWARE UPDATE FOR INFOTAINMENT ISSUES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB23-049
Service Bulletin/Repair Instructions
12 VOLT BATTERY TESTING FOR IN-SERVICE VEHICLES SERVICE INFORMATION The following Service Information lists NNA procedural recommendations for establishing good connections while performing 12V battery testing. These recommendations are expected to promote uniformity during the connection process, therefore reducing the number of incorrect âTest with DCAâ and âReplaceâ results. HINT: If 12 volt batteries are allowed to discharge for a prolonged period of time, battery life may be drastically reduced. This condition may lead to premature battery replacement and customer dissatisfaction. IMPORTANT: ï· CPX-900 is now an accepted testing tool to use along with or in place of the DSS-5000 ï· CPX-900 operating instructions are found at: https://nissancpx900.midtronics.com/ ï· DSS-5000 operating instructions are found at: https://nissandss5000.midtronics.com/ ï· DCA-8000 is now a required testing tool to be used for all warranty replacement decisions. The DCA-8000 is also a more efficient charger than previously available, and will charge any available 12 volt lead acid battery safely and accurately as long as all precautions and inputs are made correctly. The DCA-8000 operating instructions are found at: https://nissandca8000.midtronics.com/
NTB23-053
Service Bulletin/Repair Instructions
SILICONE-BASED LUBRICANT OR GREASE CAN DAMAGE ELECTRICAL COMPONENTS SERVICE INFORMATION Do not apply Silicone-based lubricants or grease to, or around, any interior electrical components. To avoid the risk of death or severe personal injury, do not directly spray Silicone-based lubricant or grease, or inadvertently overspray Silicone-based lubricant or grease onto any interior electrical components. These types of lubricants can be detrimental to the proper operation of electrical components.
NTB12-103H
Service Bulletin/Repair Instructions
CVT/TCM CALIBRATION DATA âWRITEâ PROCEDURE This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB13-107F
Service Bulletin/Repair Instructions
VEHICLE KEY NOT DETECTED / AUTHENTICATED, ENGINE WILL NOT START This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB14-012I
Service Bulletin/Repair Instructions
REMOTE ENGINE START NOT WORKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB16-003C
Service Bulletin/Repair Instructions
INTELLIGENT KEY REPLACEMENT OR SWAPPING BETWEEN VEHICLES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.
NTB18-071C
Service Bulletin/Repair Instructions
SECURITY ALARM SOUNDS AFTER USING MECHANICAL KEY TO UNLOCK DRIVER DOOR This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB21-029C
Service Bulletin/Repair Instructions
SOFTWARE UPDATE FOR INFOTAINMENT ISSUES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB23-018C
Service Bulletin/Repair Instructions
SOFTWARE UPDATE FOR INFOTAINMENT ISSUES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB03-074Q
Service Bulletin/Repair Instructions
HEADLAMP, FOG LAMP, OR REAR COMBINATION LAMP FOGGING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB12-055J
Service Bulletin/Repair Instructions
CLICKING NOISE FROM FRONT OR REAR AXLE DURING TAKE-OFF/ACCELERATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB21-029B
Service Bulletin/Repair Instructions
SOFTWARE UPDATE FOR INFOTAINMENT ISSUES This bulletin has been superseded by: NTB23-018 SOFTWARE UPDATE FOR INFOTAINMENT ISSUES Please discard previous versions of this bulletin.
NTB23-018B
Service Bulletin/Repair Instructions
SOFTWARE UPDATE FOR INFOTAINMENT ISSUES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB23-018A
Service Bulletin/Repair Instructions
SOFTWARE UPDATE FOR INFOTAINMENT ISSUES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB19-042D
Service Bulletin/Repair Instructions
AUTOMATIC EMERGENCY BRAKING WARNING LIGHT BLINKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB19-071C
Service Bulletin/Repair Instructions
DTC B00A0-00 STORED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB21-106A
Service Bulletin/Repair Instructions
DTC C1A17-49 OR C2580-49 STORED IN LASER/RADAR This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB10-145B
Service Bulletin/Repair Instructions
ABS/VDC CAN DIAGNOSIS INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB23-018
Service Bulletin/Repair Instructions
SOFTWARE UPDATE FOR INFOTAINMENT ISSUES SERVICE INFORMATION When diagnosing an infotainment issue or after replacement of the AV Control Unit, it is necessary to verify the current software version of the AV Control Unit to determine if a software version update is required. Use the vehicle tables in this bulletin to determine the current software version, if the AV Control Unit requires a software version update, and which procedure to use to update the AV Control Unit. The software updates in this bulletin are to address stability improvements and âbugâ fixes. IMPORTANT: If the customer is experiencing a software related concern, refer to NTB21-038 to verify if the customer concern is a hardware or software related issue. If the concern is a software related issue, review the information in this bulletin to update the AV Control Unit as needed.
NTB09-081J
Service Bulletin/Repair Instructions
WINDSHIELD CRACKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB13-028H
Service Bulletin/Repair Instructions
REMOVING FOREIGN MATERIAL FROM THE WINDOW GLASS This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB08-097K
Service Bulletin/Repair Instructions
DIAGNOSIS OF VEHICLE PULL (DRIFT) AND/OR STEERING WHEEL OFF-CENTER This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB10-126C
Service Bulletin/Repair Instructions
WHEEL BEARING COLLISION DAMAGE This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB20-010C
Service Bulletin/Repair Instructions
WINDSHIELD WIPER BLADE PERFORMANCE/DIAGNOSIS SERVICE INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB15-049Z
Service Bulletin/Repair Instructions
TELEMATICS SERVICE INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB22-101
Service Bulletin/Repair Instructions
DRIVE SHAFT BOOT SERVICE INFORMATION SERVICE INFORMATION If a Drive Shaft (Axle Shaft) Boot on an APPLIED VEHICLE is found to be leaking grease, AND There is no abnormal noise or obvious CV Joint risk due to water intrusion and/or complete grease loss, check for REPAIR KIT-DUST BOOT (CV Joint Boot Kit) availability. ï· If there is a REPAIR KIT-DUST BOOT (CV Joint Boot Kit) available for the vehicle being repaired, do NOT replace the axle. Install a new boot kit following the procedure in the ESM. o Refer to the ESM: TRANSMISSION & DRIVELINE > FRONT AXLE > REMOVAL AND INSTALLATION > FRONT DRIVE SHAFT BOOT o If the complete axle (drive shaft) is replaced when only a new boot is required, the over-repair may be charged back to the dealer. ï· If there is NOT a REPAIR KIT-DUST BOOT (CV Joint Boot Kit) available for the vehicle being repaired, refer to the ESM for further diagnostic information. IMPORTANT: When servicing vehicles with staked axle nuts, refer to NTB21-013 to prevent Drive Shaft thread damage.
NTB15-049Y
Service Bulletin/Repair Instructions
TELEMATICS SERVICE INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB10-029I
Service Bulletin/Repair Instructions
ABNORMAL NOISE, VIBRATION AND/OR BINDING FEELING FROM REAR DIFFERENTIAL This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB12-055I
Service Bulletin/Repair Instructions
CLICKING NOISE FROM FRONT OR REAR AXLE DURING TAKE-OFF/ACCELERATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB21-029A
Service Bulletin/Repair Instructions
SOFTWARE UPDATE FOR INFOTAINMENT ISSUES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB19-067F
Service Bulletin/Repair Instructions
SOFTWARE UPDATE FOR INFOTAINMENT ISSUES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB14-012H
Service Bulletin/Repair Instructions
REMOTE ENGINE START NOT WORKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB17-003E
Service Bulletin/Repair Instructions
FLUID LEAK CAUSED BY TRANSFER ASSEMBLY RIGHT SIDE DRIVE SHAFT OIL SEAL This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB21-094A
Service Bulletin/Repair Instructions
TRANSFER ASSEMBLY SEAL REPLACEMENT FOR AWD FRONT DRIVE SHAFT REMOVAL This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB10-029H
Service Bulletin/Repair Instructions
NISSAN AWD MODELS; ABNORMAL NOISE, VIBRATION AND/OR JUDDER FROM REAR DIFFERENTIAL This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB19-071B
Service Bulletin/Repair Instructions
DTC B00A0-00 STORED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB19-076C
Service Bulletin/Repair Instructions
DTC P17F0, P17F1, P0776, P2813, P1715, AND/OR P0841 STORED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.
NTB22-026
Service Bulletin/Repair Instructions
SERVICE INFORMATION FOR FUEL GAUGE INACCURATE WITH DTCS STORED IN ECM SERVICE INFORMATION If a fuel level sensor has been diagnosed as sending an incorrect level signal, and one or more of the following DTCs are stored in the ECM, do not replace the entire âFuel Level Sensor Unit, Fuel Filter and Fuel Pump Assemblyâ (fuel pump assembly). The fuel level sensor can be replaced separately. ï· P0460 (FUEL LEV SEN SLOSH) ï· P0461 (FUEL LEVEL SENSOR) ï· P0462 (FUEL LEVL SEN/CIRC) ï· P0463 (FUEL LEVL SEN/CIRC) NOTE: Warranty claims referring to fuel level issues that result in the replacement of the entire fuel pump assembly will be charged back.
NTB10-029G
Service Bulletin/Repair Instructions
NISSAN AWD MODELS; ABNORMAL NOISE, VIBRATION AND/OR JUDDER FROM REAR DIFFERENTIAL This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB15-049X
Service Bulletin/Repair Instructions
TELEMATICS SERVICE INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB17-003D
Service Bulletin/Repair Instructions
FLUID LEAK CAUSED BY TRANSFER ASSEMBLY RIGHT SIDE DRIVE SHAFT OIL SEAL This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB13-027C
Service Bulletin/Repair Instructions
CAN COMMUNICATION â NETWORK DIAGNOSTIC FLOW CHART This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB18-071B
Service Bulletin/Repair Instructions
SECURITY ALARM SOUNDS AFTER USING MECHANICAL KEY TO UNLOCK DRIVER DOOR This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB17-003C
Service Bulletin/Repair Instructions
FLUID LEAK CAUSED BY TRANSFER ASSEMBLY RIGHT SIDE DRIVE SHAFT OIL SEAL This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB13-097J
Service Bulletin/Repair Instructions
EVAP LEAK DTC P0442, P0455, P0456 INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB17-082E
Service Bulletin/Repair Instructions
DTC P0456 CAUSED BY EVAP LEAK AT VENT CONTROL VALVE O-RING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB17-045C
Service Bulletin/Repair Instructions
CLEANING FRONT OR REAR COMBINATION LAMP ASSEMBLIES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB19-076B
Service Bulletin/Repair Instructions
2018 ALTIMA AND 2018-2019 ROGUE; DTC P17F0, P17F1, P0776, P2813, P1715, AND/OR P0841 STORED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.
NTB99-001F
Service Bulletin/Repair Instructions
STRUT AND SHOCK ABSORBER REPLACEMENT GUIDELINES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB21-106
Service Bulletin/Repair Instructions
DTC C1A17-49 OR C2580-49 STORED IN LASER/RADAR SERVICE INFORMATION If DTC C1A17-49 or C2580-49 is stored in LASER/RADAR in the âPASTâ column: ï· Erase the DTC. ï· DO NOT replace any parts. If DTC C1A17-49 or C2580-49 is stored in LASER/RADAR in the "CURRENT" column, refer to the applicable ESM for instructions.
NTB21-094
Service Bulletin/Repair Instructions
TRANSFER ASSEMBLY SEAL REPLACEMENT FOR AWD FRONT DRIVE SHAFT REMOVAL SERVICE INFORMATION When removing the front passenger (RH) side drive shaft on an applied vehicle for any reason, transfer assembly drive shaft oil seal and dust cover seal replacement is required. Refer to the SERVICE PROCEDURE in this bulletin.
NTB18-055E
Service Bulletin/Repair Instructions
CVT FLUID LEVEL QUICK CHECK GAUGE This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB12-055H
Service Bulletin/Repair Instructions
CLICKING NOISE FROM FRONT OR REAR AXLE DURING TAKE-OFF/ACCELERATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB15-077D
Service Bulletin/Repair Instructions
SIGNAL TECH-II INTELLIGENT KEY BATTERY TEST AND SIGNAL CHECK This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB16-028D
Service Bulletin/Repair Instructions
INTELLIGENT KEY BUTTONS INOPERATIVE BUT REQUEST SWITCHES WORK This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB17-118B
Service Bulletin/Repair Instructions
NISSAN; INTELLIGENT KEY IDENTIFICATION AND REGISTRATION TIPS This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB17-003B
Service Bulletin/Repair Instructions
FLUID LEAK CAUSED BY TRANSFER ASSEMBLY RIGHT SIDE DRIVE SHAFT SEAL This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB21-035
Service Bulletin/Repair Instructions
2018-2021 LEAF AND 2017-2020 ROGUE; STEERING WHEEL CHROME FINISHER REPLACEMENT SERVICE INFORMATION If the chrome finisher on the steering wheel needs to be replaced, the chrome finisher can be ordered separately from the steering wheel. SERVICE PROCEDURE 1. Remove the driver side air bag module. ï· For removal of the driver side air bag module, refer to the Electronic Service Manual (ESM), section REPAIR â RESTRAINTS â SRS AIRBAG â REMOVAL AND INSTALLATION â DRIVER AIR BAG MODULE. NOTE: ï· When removing the chrome finisher from the steering wheel, reference Figure 2 for the 6 attachment points. ï· During removal of the chrome finisher (step 2 on page 3), pull on the chrome finisher just enough to release the pawls from the steering wheel.
NTB21-029
Service Bulletin/Repair Instructions
SOFTWARE UPDATE FOR INFOTAINMENT ISSUES SERVICE INFORMATION When diagnosing an infotainment issue, always confirm that the latest software is installed in the AV control unit before starting the diagnosis. The software update in the following service procedure is to provide: ï· Stability improvements and âbugâ fixes. Refer to steps 1-5 to confirm that this bulletin applies.
NTB16-018D
Service Bulletin/Repair Instructions
MIL ON WITH P0603 STORED FOR ECM BACK UP CIRCUIT This bulletin has been amended. See AMENDMENT HISTORY on page 3. Please discard previous versions of this bulletin.
NTB15-049W
Service Bulletin/Repair Instructions
TELEMATICS SERVICE INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB18-041D
Service Bulletin/Repair Instructions
2017-2020 ROGUE, ROGUE HYBRID, AND ROGUE SPORT; FALSE ACTIVATION OF AEB, FEB, OR FCW This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB16-028C
Service Bulletin/Repair Instructions
INTELLIGENT KEY BUTTONS INOPERATIVE BUT REQUEST SWITCHES WORK This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB19-071A
Service Bulletin/Repair Instructions
DTC B00A0-00 STORED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB15-013f
Service Bulletin/Repair Instructions
NISSAN; PROCEDURE TO CLEAN CVT TRANSMISSION FLUID COOLERS This bulletin is no longer active. Please discard previous versions of NTB15-013. Refer to the ESM for the fluid cooler cleaning procedure.
NTB99-001e
Service Bulletin/Repair Instructions
STRUT AND SHOCK ABSORBER REPLACEMENT GUIDELINES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB18-071a
Service Bulletin/Repair Instructions
SECURITY ALARM SOUNDS AFTER USING MECHANICAL KEY TO UNLOCK DRIVER DOOR This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB19-008b
Service Bulletin/Repair Instructions
NISSAN; DIAGNOSIS INFORMATION FOR DTC P161D This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB19-067e
Service Bulletin/Repair Instructions
SOFTWARE UPDATE FOR INFOTAINMENT ISSUES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB19-042b
Service Bulletin/Repair Instructions
AEB WARNING LIGHT BLINKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB20-066b
Service Bulletin/Repair Instructions
LANE CAMERA AIMING VEHICLE REFERENCE VALUES NOT IN ESM This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB19-029a
Service Bulletin/Repair Instructions
INTELLIGENT KEY DOES NOT WORK AFTER BATTERY REPLACEMENT This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB15-049v
Service Bulletin/Repair Instructions
TELEMATICS SERVICE INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB20-043a
Service Bulletin/Repair Instructions
2014-2020 ROGUE; AIR DUCT REPLACEMENT This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB14-105a
Service Bulletin/Repair Instructions
2014-2020 ROGUE; CARPET WET FRONT FLOOR AREA This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.
NTB12-110d
Service Bulletin/Repair Instructions
POWER BACK DOOR CALIBRATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.
NTB20-094
Service Bulletin/Repair Instructions
2015-2020 ROGUE; MIL ON WITH DTC P0181 AND/OR P0183 IF YOU CONFIRM The MIL is ON with DTC P0181 (FTT SENSOR) and/or P0183 (FTT SEN/CIRCUIT) stored in the ECM. ACTION 1. Remove the fuel pump assembly. 2. Inspect the fuel pump assembly wiring, and reroute the wiring, if applicable. 3. Reinstall the fuel pump assembly.
NTB20-090a
Service Bulletin/Repair Instructions
2014-2020 ROGUE; HVAC BLOWER NOISY OR WATER DRIPS ON DRIVER SIDE CARPET This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB20-090
Service Bulletin/Repair Instructions
2014-2020 ROGUE; HVAC BLOWER NOISY OR WATER DRIPS ON DRIVER SIDE CARPET IF YOU CONFIRM The customer states the HVAC blower is noisy OR Water is dripping on the driver side carpet after going through a car wash. ACTION Refer to REPAIR OVERVIEW on page 2.
NTB15-026d
Service Bulletin/Repair Instructions
2014-2020 ROGUE; LACKS POWER DUE TO SNOW INGESTION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
DOR-H5Y5B-01
Service Bulletin/Repair Instructions
This SKU is a Suspension Ball Joint. The customer communication requested return of unsold inventory to inspect for the outer diameter of the ball joint housing being too small. The outer diameter being too small would prevent the part from being installed, and would therefore have no impact on the end user besides time to complete installation.
NTB19-067d
Service Bulletin/Repair Instructions
SOFTWARE UPDATE FOR INFOTAINMENT ISSUES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB19-042a
Service Bulletin/Repair Instructions
AEB WARNING LIGHT BLINKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB20-075
Service Bulletin/Repair Instructions
SOFTWARE UPDATE POP-UP NOTIFICATION SERVICE INFORMATION The infotainment system of the applied vehicle has the ability to update its software through an over-the-air (OTA) link. As software updates become available for new features, and/or patches, the software update screen (pop-up) shown in Figure 1 will automatically be displayed. Much like cell phone and computer updates, this is a normal feature which allows the user to choose when an update is downloaded. ï· It is recommended that while in dealer inventory and this pop-up appears, that â Yesâ is selected to provide the latest software version to the customer at delivery. NOTE: If the ignition is turned OFF in the middle of a download, it will automatically restart when the ignition is turned back ON. When one of the following is selected: Yesâ¦..The pop-up is hidden and the download starts in the background. Laterâ¦The pop-up is hidden and displayed again in the next key cycle (after cold start).
NTB19-076a
Service Bulletin/Repair Instructions
2018 ALTIMA AND 2018-2019 ROGUE; DTC P17F0, P17F1, P0776, P2813, P1715, AND/OR P0841 STORED IF YOU CONFIRM One or more of the following DTCs are stored: P0776, P2813, P0841, P17F0, P17F1, P1715 HINT: ï· If DTCs other than those listed above are stored, this bulletin does not apply. ï· If the customer states the engine stalled while going from 'P' or 'N' range to 'R' or 'D' range, this bulletin does not apply. ï· If DTC P17F0 and/or P17F1 are the only DTCs stored and there is no customer complaint of judder, this bulletin does not apply. ï· If DTC P1715 is the only code stored, this bulletin does not apply. ACTION See Repair Flow Chart on page 2 to confirm if this bulletin applies. HINT: The following pages must be printed and attached to the RO: 1. Clutch Total End Play Calculation (Step 97 on page 63) 2. Consult screen shot showing the TCM part numbers (Step 152 on page 89) 3. Current Calibration Data (Step 155 on page 90) 4. New Calibration Data (Step 171 on page 91) 5. Parts Kit Reference Table (Page 99)
NTB20-066a
Service Bulletin/Repair Instructions
LANE CAMERA AIMING VEHICLE REFERENCE VALUES NOT IN ESM This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB20-069
Service Bulletin/Repair Instructions
ROGUE AND ROGUE SPORT; VIBRATION AND/OR NOISE WHEN MAKING LOW SPEED TURNS IF YOU CONFIRM There is a vibration or judder feeling from the rear of the vehicle during the following conditions: ï· When making turns ï· On dry roads ï· At low speeds (under 40 MPH) And ï· The above vibration does not occur if the electric controlled coupling is electrically disconnected. ACTION 1. Confirm the AWD control unit part number, and replace it, if applicable. 2. Replace the electric controlled coupling for the rear final drive. 3. Perform Unit Characteristics Writing.
NTB20-066
Service Bulletin/Repair Instructions
LANE CAMERA AIMING VEHICLE REFERENCE VALUES NOT IN ESM SERVICE INFORMATION If the lane camera requires aiming, the values in Table A on page 4 must be used. ï· For all other models/model years, consult the Electronic Service Manual (ESM). The following CONSULT-III plus (C-III plus) figures and steps are only provided to indicate where the VEHICLE REFERENCE VALUE from Table A is to be entered. The entire camera aiming procedure must be followed to complete the aiming procedure. ï· Refer to the ESM section: CRUISE CONTROL & DRIVER ASSISTANCE > DRIVER ASSISTANCE SYSTEM > DRIVER ASSISTANCE SYSTEM > BASIC INSPECTION > LANE CAMERA UNIT > CAMERA AIMING ADJUSTMENT. 1. Turn the ignition ON. 2. From the C-III plus home screen, select Diagnosis (One System).
NTB20-050
Service Bulletin/Repair Instructions
POWER BACK DOOR WILL NOT OPERATE WITH REQUEST SWITCHES IF YOU CONFIRM On vehicles equipped with a Kick Motion Activated Liftgate, the back door (liftgate) will not open or close when requested to do so using the: ï· Intelligent Key ï· Back door request switch, located on the back door ï· Automatic back door switch, located on the instrument lower panel LH And DTC B2409 is either current or has been stored in the past. ACTION Replace the automatic back door control module. ï· Refer to the Electronic Service Manual (ESM) section: BODY EXTERIOR, DOORS, ROOF & VEHICLE SECURITY > DOOR & LOCK > WITH INTELLIGENT KEY SYSTEM > REMOVAL AND INSTALLATION > AUTOMATIC BACK DOOR CONTROL MODULE.
NTB18-033b
Service Bulletin/Repair Instructions
ACCELERATOR PEDAL VIBRATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB19-067c
Service Bulletin/Repair Instructions
SOFTWARE UPDATE FOR INFOTAINMENT ISSUES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB20-043
Service Bulletin/Repair Instructions
2015-2020 ROGUE; AIR DUCT REPLACEMENT IF YOU CONFIRM Air duct 1, air duct 2, or the air cleaner cover shown in Figure 1 needs to be replaced. ACTION Inspect for a clip in the location shown in Figure 1 and Figure 2. ï· If a clip is present, then the vehicle IS equipped with the updated parts; no further action is needed. Individual parts may be replaced as needed. ï· If a clip is NOT present, then the vehicle is equipped with older parts. See SERVICE PROCEDURE on the next page.
NTB15-049u
Service Bulletin/Repair Instructions
TELEMATICS SERVICE INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB17-003a
Service Bulletin/Repair Instructions
FLUID LEAK CAUSED BY TRANSFER ASSEMBLY RIGHT SIDE DRIVE SHAFT SEAL This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB18-055d
Service Bulletin/Repair Instructions
CVT FLUID LEVEL QUICK CHECK GAUGE This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB15-049t
Service Bulletin/Repair Instructions
TELEMATICS SERVICE INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB12-055g
Service Bulletin/Repair Instructions
CLICKING NOISE FROM FRONT OR REAR AXLE DURING TAKE-OFF/ACCELERATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB17-057c
Service Bulletin/Repair Instructions
2015-2020 ROGUE AND 2017-2020 ROGUE SPORT; DISTANCE TO EMPTY DOES NOT RESET This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB15-013e
Service Bulletin/Repair Instructions
NISSAN; PROCEDURE TO CLEAN CVT TRANSMISSION FLUID COOLERS This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB19-080
Service Bulletin/Repair Instructions
2014-2020 ROGUE; NO AIR FLOW FROM VENTS DUE TO SNOW BUILD-UP IF YOU CONFIRM Or the customer states there is no air flow from any of the HVAC vents And There is snow build-up in and around the blower motor air inlet, behind the cowl. ACTION 1. Remove all snow, water, and debris from the blower motor inlet, cowl area, and where the blower motor mounts. 2. Clean or replace the blower motor as needed. 3. If the blower motor does not work on all speed settings, replace the variable blower control (fan resistor). 4. If not already equipped: Install the cowl and wiper pivot filters listed in PARTS INFORMATION on the last page of this bulletin.
White Paint Clas
Service Bulletin/Repair Instructions
White Paint Class Action Owner Notification Dealer Notification In October, owners of white Nissan Rogues produced between January 11, 2013 and April 23, 2013, will receive a notice from a settlement administrator informing them of the terms of a proposed class action settlement. The settlement, if approved by the presiding court, could extend the warranty on the paint for four years and provide a one-time full vehicle repaint (subject to a copay). Eligible owners can also obtain coverage for any reasonable and necessary rental car coverage arising from the repaint, or reimbursement of amounts previously incurred for a one-time repaint and any reasonable and necessary rental car services arising from the repaint. The settlement also provides for eligibility in Nissanâs Vehicle Purchase Program. To be clear, unless and until the proposed settlement is approved by the presiding court, there is no warranty extension or other remedy and you should proceed with paint-related claims in the ordinary course. The proposed settlement, and the associated potential warranty extension, include many terms and conditions. Rather than attempting to address questions about the proposed settlement terms from customers, Nissan recommends dealers refer customers to the website listed below. This will enable owners to receive information from appropriate sources and avoid providing incorrect and/or incomplete information to customers. The website is currently live and available to inquiring customers. ***** What Dealers Should Do ***** 1. No action is necessary at this time. Nissan will provide additional instructions once the proposed settlement is approved by the court. 2. If a customer contacts the dealer with a white paint concern and/or references this settlement notification, dealers should refer the customer to the third party administratorâs website for additional information. www.vehiclepaintsettlement.com
NTB17-028a
Service Bulletin/Repair Instructions
2014-2020 ROGUE; BLOWER MOTOR SERVICE INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB19-067b
Service Bulletin/Repair Instructions
SOFTWARE UPDATES FOR INFOTAINMENT ISSUES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB19-072
Service Bulletin/Repair Instructions
TRANSMISSION RANGE SWITCH SERVICE INFORMATION SERVICE INFORMATION The transmission range switch of the APPLIED VEHICLES listed above is now available as a separate service part. If the transmission range switch of an APPLIED VEHICLE is being replaced for any reason, it must be adjusted after its replacement. ï· Refer to SERVICE PROCEDURE on page 3 for transmission range switch removal, installation, and adjustment.
NTB19-071
Service Bulletin/Repair Instructions
DTC B00A0-00 STORED IF YOU CONFIRM DTC B00A0-00 (OCCUPANT DETECTION SENSOR UNIT) is stored And OCS zero point reset cannot be performed (continued on the next page) And The following screen displays: ACTION 1. Check the Occupant Classification System (OCS) control unit using the ODS Analysis tool software. ï· Refer to SERVICE PROCEDURE on page 5. HINT: âOCSâ may also be referred to as âODSâ. 2. Perform â75-zero RESETâ.
NTB19-067a
Service Bulletin/Repair Instructions
SOFTWARE UPDATES FOR INFOTAINMENT ISSUES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB17-111d
Service Bulletin/Repair Instructions
NISSANCONNECT OVER THE AIR SOFTWARE UPDATE This bulletin has been superseded by NTB19-067. Please discard previous versions of this bulletin.
NTB19-067
Service Bulletin/Repair Instructions
SOFTWARE UPDATES FOR INFOTAINMENT ISSUES SERVICE INFORMATION When diagnosing an infotainment issue, always confirm that the latest software is installed in the AV unit before starting the diagnosis. The software updates in the following Service Procedure are for the items below: ï· Stability improvements and bug fixes ï· System enhancements that will allow future Over-The-Air (OTA) updates. Without these software updates, future OTAs will not be possible. Refer to step 5 on page 5 to confirm that this bulletin applies. HINT: The update software only needs to be downloaded once and can then be used on multiple Applied Vehicles until other infotainment software is loaded onto the USB drive to overwrite the original data.
NTB18-041c
Service Bulletin/Repair Instructions
2017-2020 ROGUE, ROGUE HYBRID, AND ROGUE SPORT; FALSE ACTIVATION OF AEB, FEB, OR FCW This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB14-012e
Service Bulletin/Repair Instructions
REMOTE ENGINE START NOT WORKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
PC687 Rogue
Service Bulletin/Repair Instructions
Left Rear Brake Caliper Voluntary Service Campaign ***** Campaign Summary***** Nissan is conducting a Voluntary Service Campaign to inspect and if necessary replace the left rear brake caliper in certain 2019 model year Rogue (T32) vehicles. Subject vehicles that are equipped with a left rear caliper with a specific lot code do not meet Nissan quality standards. If the vehicle is equipped with a subject brake caliper, the caliper mounting may crack. While vehicle braking effectiveness may be reduced in this condition, the customer?s ability to control and decelerate the vehicle will not be significantly affected. To identify if this condition exists, dealers will inspect the lot code and, if applicable, replace the left rear brake caliper. ***** What Dealers Should Do ***** 1. Verify if vehicles are affected by this Voluntary Service Campaign using Service Comm or DBS National Service History - Open Campaign I.D. PC687. 2. Dealers should repair any affected vehicles in retailer new or pre-owned inventory to help ensure customer satisfaction. 3. Dealers should use NTB19-051 to inspect and, if necessary, remedy any vehicles subject to this campaign. 4. The service department should submit the applicable warranty claim for the action performed so it can be closed on Service Comm and release the vehicle.
NTB19-051
Service Bulletin/Repair Instructions
VOLUNTARY SERVICE CAMPAIGN 2019 ROGUE; LEFT REAR BRAKE CALIPER ASSEMBLY INTRODUCTION Nissan is conducting this voluntary service campaign on certain specific model year 2019 Rogue vehicles. The left rear brake caliper assembly will be inspected, and replaced if needed. This service will be performed at no charge to the customer for parts or labor. IDENTIFICATION NUMBER Nissan has assigned identification number PC687 to this campaign. This number must appear on all communication and documentation of any nature dealing with this campaign. DEALER RESPONSIBILITY Dealers are to repair vehicles falling within range of this campaign that enter the service department. This includes vehicles purchased from private parties, vehicles presented by transient (tourists) owners, and vehicles in a dealer?s inventory.
NTB15-049s
Service Bulletin/Repair Instructions
TELEMATICS SERVICE INFORMATION This bulletin applies only to vehicles equipped with a Telematics Communication Unit (TCU). This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB18-055c
Service Bulletin/Repair Instructions
CVT FLUID LEVEL QUICK CHECK GAUGE This bulletin applies only to vehicles equipped with a Continuously Variable Transmission (CVT). This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB19-042
Service Bulletin/Repair Instructions
AEB WARNING LIGHT BLINKING This bulletin applies only to vehicles equipped with a lane camera. SERVICE INFORMATION If the AEB warning light is blinking (but not illuminated steadily) or the customer states it is blinking, and there are no related DTCs, inspect the windshield. A blinking AEB warning light may occur under the following conditions: - When contamination or foreign material adhere to the lane camera viewing window on the windshield - When driving while it is snowing or when frost forms on the lane camera viewing window on the windshield - When the lane camera viewing window on the windshield is temporarily fogged up NOTE: - If DTCs are present in any of the following related systems: - Laser/Radar, - ICC/ADAS, or - Lane Camera, Refer to the related Electronic Service Manual (ESM) for diagnosis. - Refer to the following pages for further information.
NTB19-008a
Service Bulletin/Repair Instructions
NISSAN; DIAGNOSIS INFORMATION FOR DTC P161D This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB19-029
Service Bulletin/Repair Instructions
INTELLIGENT KEY DOES NOT WORK AFTER BATTERY REPLACEMENT SERVICE INFORMATION If the Intelligent Key of an APPLIED VEHICLE does not work after replacing the battery, inspect the positive (+) terminals. If the battery side of the Intelligent Key is held by pinching down on the terminals while removing the battery, it is possible to bend the terminals down far enough that they will not touch the contacts on the other half of the Intelligent Key. If the terminals are found to be bent down, pry them back up so that they will come in contact with the other half of the Intelligent Key?s contacts. - Refer to the photos on the following pages.
NTB12-100b
Service Bulletin/Repair Instructions
CVT / TCM CALIBRATION DATA ?WRITE? PROCEDURE This bulletin applies only to vehicles equipped with a Continuously Variable Transmission (CVT). This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB12-103g
Service Bulletin/Repair Instructions
CVT / TCM CALIBRATION DATA ?WRITE? PROCEDURE This bulletin applies only to vehicles equipped with a Continuously Variable Transmission (CVT). This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB18-055b
Service Bulletin/Repair Instructions
CVT FLUID LEVEL QUICK CHECK GAUGE This bulletin applies only to vehicles equipped with a Continuously Variable Transmission (CVT). This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.
NTB19-022
Service Bulletin/Repair Instructions
NISSAN; P0171 AND P0174 SERVICE INFORMATION SERVICE INFORMATION Diagnosis for DTCs P0171 (FUEL SYS LEAN B1) and P0174 (FUEL SYS LEAN B2) have been revised for the APPLIED VEHICLES listed above. When performing diagnosis for either of these DTCs, start by using the SERVICE PROCEDURE section of this bulletin. NOTE: The related Electronic Service Manuals (ESM) will be revised in the future to include these diagnostic steps.
NTB19-021
Service Bulletin/Repair Instructions
NISSAN; MIL ON WITH DTC P219A AND/OR P219B STORED This bulletin applies to Titan XD vehicles equipped with a VK56D gas engine only. SERVICE INFORMATION If the MIL is ON and DTC P219A (AIR FUEL RATIO IMBALANCE B1) and/or P219B (AIR FUEL RATIO IMBALANCE B2) is stored: - DO NOT replace the Air Fuel Ratio (A/F) sensor. - Refer to the applicable Electronic Service Manual (ESM) and follow the diagnostic procedure for DTC P219A and/or P219B.
PC687 Rogue Rear
Service Bulletin/Repair Instructions
Rear Brake Caliper *****Dealer Announcement***** Nissan is conducting a quality action to inspect the lot code on the left hand rear brake caliper on 14 specific 2019 Rogue vehicles identified in Service Comm, and if necessary, replace the brake caliper. Affected vehicles are subject to stop sale and are either currently in dealer inventory or assigned and in transit to the dealer. *****What Dealers Should Do***** PLEASE FOLLOW THE ATTACHED REPAIR INSTRUCTIONS: 1. Verify if vehicles currently in new dealer inventory are affected by this quality action using Service Comm I.D. PC687 ? New vehicles in dealer inventory can also be identified using DCS (Sales-> Vehicle Inventory, and filter by Open Campaign). ? Refer to NPSB 15-460 for additional information ? Please continue to check newly arriving inventory for campaign applicability. 2. Use the attached procedure to inspect the left hand rear brake caliper: ? If the lot code is 9A24, the brake caliper must be replaced ? Nissan has developed an automatic parts shipment to proactively provide affected dealers with replacement brake calipers for affected vehicles in dealer inventory, in the event they are needed. Parts should begin to arrive at dealers on February 27, 2019 ? If not, reassemble the wheel and tire 3. The service department should submit the applicable warranty claim for the action performed so it can be closed on Service Comm and release the vehicle. ***** Dealer Responsibility ***** It is the dealer?s responsibility to check Service Comm or DBS National Service History ? Open Campaign using the appropriate campaign I.D for the inspection status on each affected vehicle currently in new vehicle inventory.
NTB16-028b
Service Bulletin/Repair Instructions
INTELLIGENT KEY BUTTONS INOPERATIVE BUT REQUEST SWITCHES WORK This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB13-097g
Service Bulletin/Repair Instructions
ALL MODEL YEAR 2012 AND NEWER NISSAN VEHICLES; EVAP LEAK DTC P0442, P0455, P0456 INFORMATION This bulletin does NOT apply to LEAF vehicles and Titan XD vehicles with V8 diesel engine. This bulletin has been amended. See Amendment History on the last page. Please discard previous versions of this bulletin.
NTB15-049r
Service Bulletin/Repair Instructions
TELEMATICS SERVICE INFORMATION This bulletin applies only to vehicles equipped with a Telematics Communication Unit (TCU). This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB17-082b
Service Bulletin/Repair Instructions
NISSAN; DTC P0456 CAUSED BY EVAP LEAK AT VENT CONTROL VALVE O-RING This bulletin does NOT apply to LEAF vehicles and Titan XD vehicles with V8 diesel engine. This bulletin has been amended. See Amendment History on the last page. Please discard previous versions of this bulletin.
NTB19-008
Service Bulletin/Repair Instructions
NISSAN; DIAGNOSIS INFORMATION FOR DTC P161D SERVICE INFORMATION When key registration is unsuccessful after BCM replacement, P161D (Immobilizer) will set when the ignition is turned on. Possible causes - Improper key registration - Defective BCM (Vehicles with Intelligent Key only) - EPS control unit (Vehicles with mechanical key only) - Intelligent Key unit (Vehicles with mechanical key only) Trouble Diagnosis NOTE: If DTC B2196-52 is stored with P161D, perform the diagnosis procedure for DTC B2196-52 first. - Before replacing the BCM, confirm that the keys were programmed correctly by ensuring the vehicle will start and that the lock/unlock buttons function normally. - If any keys do not function normally, re-register all of the keys. - After re-registering all of the keys, reconfirm each key's function. - If OK, erase the code to complete the repair. - If NG, diagnose the Key, BCM and/or EPS control unit per the ESM.
NTB19-009
Service Bulletin/Repair Instructions
2017-2019 ROGUE, ROGUE HYBRID AND ROGUE SPORT; CHASSIS CONTROL UNIT AND ADAS CONTROL UNIT 2 IDENTIFICATION SERVICE INFORMATION The CONTROLLER ASSY-IDM (Chassis Control Unit) and the CONTROLLER ASSYWARNING SPEAKER (ADAS Control Unit 2) may be incorrectly identified while diagnosing for related issues. The Chassis Control Unit and the ADAS Control Unit 2: - Cases, externally, appear identical. - Are located behind the glove box, in the same area. - Harness connectors are the same, and can be connected to the wrong component. NOTE: See Figure 1 for the correct locations of the Chassis Control Unit and the ADAS Control Unit 2. - Can be identified by their location (shown in Figure 1) and confirmed by the part number on the contorol unit?s label.
P8337 2019 Rogue
Service Bulletin/Repair Instructions
Fuel Tank Band Bolt Dealer Inventory *****Dealer Announcement***** Nissan is conducting a quality action to torque the front fuel tank band bolts to specification on 12 specific 2019 Rogue Sport (J11) vehicles identified in Service Comm. Affected vehicles are not subject to stop sale and are either currently in dealer inventory or assigned and in transit to the dealer. Nissan requests dealers to complete this repair prior to sale to ensure customer satisfaction. *****What Dealers Should Do***** PLEASE FOLLOW THE ATTACHED REPAIR INSTRUCTIONS: 1. Verify if vehicles are affected by this quality action using Service Comm or DBS National Service History ? Open Campaigns I.D. P8337. - New vehicles in dealer inventory can also be identified using DBS (Sales-> Vehicle Inventory, and filter by Open Campaign). - Refer to NPSB 15-460 for additional information - Please continue to check newly arriving inventory for campaign applicability. 2. Dealers should use the attached procedure to remedy any vehicle affected by this quality action. 3. The service department should submit the applicable warranty claim for the action performed so it can be closed on Service Comm and release the vehicle. ***** Dealer Responsibility ***** It is the dealer?s responsibility to check Service Comm or DBS National Service History ? Open Campaign using the appropriate campaign I.D for the campaign status on each affected vehicle currently in new vehicle inventory.
NTB19-001
Service Bulletin/Repair Instructions
CHASSIS CONTROL MODULE DTC INFORMATION SERVICE INFORMATION If one or more of the following Chassis Control DTCs are stored: - C1BA0-00 ? (CHASSIS CONTROL BRAKE SYSTEM) - C1B92-00 ? (BRAKE CONTROL SYSTEM) - C1B93-00 ? (ENGINE/HEV SYSTEM) - C1B94-00 ? (TRANSMISSION SYSTEM) And One or more additional DTCs, other than those above, are also stored in a control unit other than the Chassis Control Module. - Perform the diagnostic/repair procedures for the additional DTCs of the other control unit FIRST. - Refer to the Electronic Service Manual (ESM) for DTC specific diagnostic information. Do not replace the CHASSIS CONTROL MODULE (CONTROLLER ASSY-IDM) if additional DTCs are present.
NTB18-083
Service Bulletin/Repair Instructions
2014 - 2019 ROGUE; SQUEAK/CREAK NOISE FROM FRONT SUSPENSION BOUND BUMPER DRIVING OVER BUMPS IF YOU CONFIRM Using the flow chart on page 2, a squeak/creak noise is heard coming from the left or right front suspension bound bumper when driving over speed bumps or similar road surfaces. NOTE: This squeak/creak noise, if it should occur, is more noticeable in cold weather. ACTION Replace the front suspension bound bumper, only on the side that is making noise. - Refer to the appropriate Electronic Service Manual (ESM) for replacement information. SUSPENSION > FRONT SUSPENSION > REMOVAL AND INSTALLATION > FRONT COIL SPRING AND STRUT > Removal and Installation. - Pages 4 - 6 in this bulletin contain helpful information to perform this procedure. - Make sure to replace the one-time-use nuts listed in the PARTS INFORMATION. - Check the front wheel alignment; adjust to factory specifications as needed. NOTE: DO NOT apply lubricant to the bound bumper to resolve this issue.
NTB18-033a
Service Bulletin/Repair Instructions
2014 ? 2019 ROGUE; ACCELERATOR PEDAL VIBRATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB17-057b
Service Bulletin/Repair Instructions
2015-2019 ROGUE AND 2017-2019 ROGUE SPORT; DISTANCE TO EMPTY DOES NOT RESET This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB12-103f
Service Bulletin/Repair Instructions
CVT / TCM CALIBRATION DATA ?WRITE? PROCEDURE This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB18-071
Service Bulletin/Repair Instructions
SECURITY ALARM SOUNDS AFTER USING MECHANICAL KEY TO UNLOCK DRIVER DOOR SERVICE INFORMATION Applied Vehicles listed above are no longer equipped with a door unlock sensor and/or Body Control Module (BCM) software to provide support for the door unlock sensor. Normal Functionality For Vehicles Built Without Door Unlock Sensor And/Or BCM Software To Support Door Unlock Sensor For Applied Vehicles built after the Applied Dates listed on page 1, using the mechanical key on the driver door will operate differently than vehicles built before the Applied Dates. For these later models, the BCM will not recognize operation of the mechanical key. If a mechanical key is used to lock the driver door: - The security system will not set. If the vehicle is broken into, the alarm will not sound. - Only the driver door will be locked. Other doors will not lock using the mechanical key. If a mechanical key is used to unlock the driver door: - Only the driver door will be unlocked. Other doors will not be unlocked. - If the security system is set, when the door is opened the alarm will sound. NOTE: Using the Unlock button on the Intelligent Key, pushing the request switch on the driver or passenger door with the Intelligent Key in range, or using the Intelligent Key to start the vehicle will silence the alarm. The mechanical key will not operate the power windows.
NTB15-077b
Service Bulletin/Repair Instructions
NISSAN; SIGNAL TECH-II INTELLIGENT KEY BATTERY TEST AND SIGNAL CHECK This bulletin has been amended. See Amendment History on the last page. Please discard previous versions of this bulletin.
NTB03-074m
Service Bulletin/Repair Instructions
FOG LAMP AND/OR HEADLAMP FOGGING This bulletin has been amended to add Fog Lamps and modify one step in the flow chart on page 3. No other changes have been made. Please discard previous versions of this bulletin.
NTB16-018c
Service Bulletin/Repair Instructions
MIL ON WITH P0603 STORED FOR ECM BACK UP CIRCUIT This bulletin does NOT apply to Titan equipped with Cummins V8 Diesel engine. This bulletin has been amended to add a NOTE in the Applied Vehicles. No other changes have been made. Please discard previous versions of this bulletin.