Vehicle report

2016 NISSAN TITAN XD

Compare every NISSAN TITAN XD yearNHTSA and EPA records

Service bulletins

280 bulletins

Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.

NTB16-079A

Service Campaign

VOLUNTARY SERVICE CAMPAIGN 2016 TITAN XD; ELECTRONIC TAILGATE LOCK

NTB16-081A

Service Campaign

VOLUNTARY SERVICE CAMPAIGN 2016 TITAN XD; RUNNING BOARDS Campaign ID # PC428 is no longer active. · Repair orders opened after this bulletin’s published date are no longer eligible for reimbursement under Campaign ID # PC428. · Discard all previous versions of NTB16-081.

NTB09-131C

Service Bulletin/Repair Instructions

CERTIFICATION LABEL AND VIN PLATE REPLACEMENT SERVICE INFORMATION Because of collision damage or other vehicle repair, a replacement “Certification Label” or “VIN Plate/Label” may be needed. HINT: Certification Label = FMVSS (Federal Motor Vehicle Safety Standards) label. These items may be available from Nissan by request if certain criteria are met. This bulletin lists the criteria and provides an application form for such replacements. · The “VIN Plate/Label” (metal plate or vinyl label) is attached to the instrument panel or body on the driver side at the base of the windshield (see Figure 1). · The “Certification Label” (vinyl adhesive label) is located on the lower area of the driver side B-Pillar (see Figure 1).

NTB23-023B

Service Bulletin/Repair Instructions

FLUID LEAK FROM THE FRONT DIFFERENTIAL CASE ACTUATOR MOTOR PLASTIC THREADS SERVICE INFORMATION Figure 1 Figure 2 If the front differential has a fluid leak coming from the actuator motor plastic threads (Figure 1): a. Place an alignment mark on the splined actuator body and the gear carrier (Figure 2). b. Remove the actuator and thoroughly clean the threads, making sure not to allow RTV to fall into the differential case. c. Once clean, apply Three Bond sealant to the threads, and then reinstall the actuator motor, making sure to line up the alignment marks. d. Check the front differential gear oil level and top to specification. o Refer to the ESM: TRANSMISSION & DRIVELINE > DRIVELINE > FRONT FINAL DRIVE: MA235/MA210 > PERIODIC MAINTENANCE > FRONT DIFFERENTIAL GEAR OIL DO NOT replace the front differential due to a fluid leak from the actuator motor plastic threads unless there has been consequential damage due to fluid loss (bearing failure or gear noise) to the front differential.

NTB24-061

Emissions

CAMPAIGN BULLETIN Cummins NOx Emissions Voluntary Emission Recall Campaign PD128 PD129 ***** Campaign Summary ***** Nissan is conducting a Voluntary Emissions Recall Campaign on certain 2016-2019 Titan Diesel vehicles identified in Service Comm and DBS National Service History. Vehicles affected by this campaign require upgraded emissions control software and hardware for model years 2016-2017 or upgraded software only for model years 2018-2019. This finding has no effect on the safety of the vehicle. Cummins and the California Air Resources Board have entered into an agreement to correct this condition. In order to implement this correction, Nissan is conducting a Voluntary Emission Recall Campaign. The remedy and parts are now available. Nissan dealers will update the emissions control software and install a Particulate Matter Sensor for model years 2016-2017 and update emissions control software only for model years 2018-2019. IMPORTANT: It is a violation of Federal law for dealers to sell or deliver new vehicles in their inventory covered by this notification until the campaign’s remedy action is performed.): REVISION 2 Please discard earlier versions of this bulletin. The announcement from January 10, 2025 has been revised to include the following: • The remedy and parts are now available, please refer to NTB24-061 to remedy any vehicle affected by PD128 and NTB24-062 to remedy any vehicle affected by PD129.  Parts are on restriction and can be ordered via DBS. Affected Models/Years: Affected Population: Dealer Inventory: SERVICE COMM Activation date: Stop Sale In Effect 2016-2017 Titan (A61D) 27,085 NA December 20, 2024 NO Affected Models/Years: Affected Population: Dealer Inventory: SERVICE COMM Activation date: Stop Sale In Effect 2018-2019 Titan (A61D) 11,614 ***** Campaign Summary ***** Nissan is conducting a Voluntary Emissions Recall Campaign on certain 2016-2019 Titan Diesel vehicles identified in Service Comm and DBS National Service History. Vehicles affected by this campaign require upgraded emissions control software and hardware for model years 2016-2017 or upgraded software only for model years 2018-2019. This finding has no effect on the safety of the vehicle. Cummins and the California Air Resources Board have entered into an agreement to correct this condition. In order to implement this correction, Nissan is conducting a Voluntary Emission Recall Campaign. The remedy and parts are now available. Nissan dealers will update the emissions control software and install a Particulate Matter Sensor for model years 2016-2017 and update emissions control software only for model years 2018-2019.

NTB24-063

Emissions

CAMPAIGN BULLETIN VECI Label Voluntary Emission Recall Campaign ***** Campaign Summary ***** Nissan is conducting a Voluntary Emissions Recall Campaign on specific model year 2016-2019 Titan Diesel vehicles identified in Service Comm and DBS National Service History. Vehicles affected by this campaign may have been shipped to market with an Exemption label and should have been shipped with a Vehicle Emission Control Information (VECI) label. Nissan dealers will inspect for the Exemption label and/or VECI label, and remove Exemption label if present and install VECI label if not present. ***** What Dealers Should Do**** 1. Verify if vehicles are affected by this Voluntary Emission Recall Campaign using Service Comm or DBS National Service History Campaign I.D. PD127. 2. Dealers should use NTB24-063 to remedy any vehicles affected by this campaign. 3. Once remedied, dealers should submit the claim, using the claims coding provided, and release the vehicle. ***** Release Schedule ***** Parts Refer to NTB24-063 to determine the parts required for this campaign. Part numbers 14805-EZ40B and 14805-9FU5A are on restriction and can be ordered via DBS. Part numbers 14805-EZ40A and 14805-EZ41C can be ordered via the normal process. Repair • NTB24-063 Owner Notification Nissan will begin sending notifications to owners of all potentially affected vehicles in February 2025, via U.S. Mail.

NTB19-071D

Service Bulletin/Repair Instructions

DTC B00A0-00 STORED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin. IF YOU CONFIRM DTC B00A0-00 (OCCUPANT DETECTION SENSOR UNIT) is stored, AND OCS zero point reset cannot be performed, (continued on the next page)

NTB10-066C

Service Bulletin/Repair Instructions

CAN COMMUNICATION CODES – DIAGNOSTIC TIPS AND GUIDELINES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB13-027D

Service Bulletin/Repair Instructions

CAN COMMUNICATION – NETWORK DIAGNOSTIC FLOW CHART This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB13-107G

Service Bulletin/Repair Instructions

VEHICLE KEY NOT DETECTED / AUTHENTICATED, ENGINE WILL NOT START This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB21-106B

Service Bulletin/Repair Instructions

DTC C1A17-49 OR C2580-49 STORED IN LASER/RADAR This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB09-081K

Service Bulletin/Repair Instructions

WINDSHIELD CRACKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB13-028I

Service Bulletin/Repair Instructions

REMOVING FOREIGN MATERIAL FROM THE WINDOW GLASS This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB17-019H

Service Bulletin/Repair Instructions

WINDOW GLASS WARRANTY INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB23-018G

Service Bulletin/Repair Instructions

NTB23-018F

Service Bulletin/Repair Instructions

SOFTWARE UPDATE FOR INFOTAINMENT ISSUES This bulletin is no longer active. To access infotainment software updates via the Infotainment Software Update Utility: Select SPECIALTY TOOLS, and then select Infotainment Software Updates on the left side of ASIST. HINT: Initially, the Infotainment Software Update Utility will be available only on the CONSULT PC version of ASIST. The Utility will be added to ASIST WEB at a later date. Please discard previous versions of NTB23-018.

NTB24-007

Service Bulletin/Repair Instructions

DIAGNOSING REAR FINAL DRIVE ASSEMBLY LEAKS SERVICE INFORMATION If a Rear Final Drive Assembly (rear solid axle) is found to be leaking from one, or more, of the locations listed below, the source(s) of the leak should first be identified and, if possible repaired before the Rear Final Drive Assembly is considered for replacement. A Rear Final Drive Assembly should not be replaced unless bearing, gear, or other significant damage has occurred. Possible points of fluid leaks: ï· Front Oil Seal (Pinion Seal) ï· Axle Tube Seal ï· ABS Rear Wheel Sensor ï· Rear Axle Wheel Bearing Seal ï· Gear Carrier Cover Gasket ï· Drain Plug IMPORTANT: If a Rear Final Drive Assembly is found to have been replaced for a repairable leak and no internal damage is present, the claim will be charged back. Refer to pages 2-5 for additional information that illustrates and/or describes some, but not all, possible points where fluid leaks can occur, as well as helpful service HINTs. ï· This bulletin is only intended as a diagnostic reference and does not direct or imply repair. ï· Refer to the ESM for any applicable repair procedures, if needed.

NTB08-097L

Service Bulletin/Repair Instructions

DIAGNOSIS OF VEHICLE PULL (DRIFT) AND/OR STEERING WHEEL OFF-CENTER This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB23-018E

Service Bulletin/Repair Instructions

SOFTWARE UPDATE FOR INFOTAINMENT ISSUES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB23-018D

Service Bulletin/Repair Instructions

SOFTWARE UPDATE FOR INFOTAINMENT ISSUES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB23-049

Service Bulletin/Repair Instructions

12 VOLT BATTERY TESTING FOR IN-SERVICE VEHICLES SERVICE INFORMATION The following Service Information lists NNA procedural recommendations for establishing good connections while performing 12V battery testing. These recommendations are expected to promote uniformity during the connection process, therefore reducing the number of incorrect âTest with DCAâ and âReplaceâ results. HINT: If 12 volt batteries are allowed to discharge for a prolonged period of time, battery life may be drastically reduced. This condition may lead to premature battery replacement and customer dissatisfaction. IMPORTANT: ï· CPX-900 is now an accepted testing tool to use along with or in place of the DSS-5000 ï· CPX-900 operating instructions are found at: https://nissancpx900.midtronics.com/ ï· DSS-5000 operating instructions are found at: https://nissandss5000.midtronics.com/ ï· DCA-8000 is now a required testing tool to be used for all warranty replacement decisions. The DCA-8000 is also a more efficient charger than previously available, and will charge any available 12 volt lead acid battery safely and accurately as long as all precautions and inputs are made correctly. The DCA-8000 operating instructions are found at: https://nissandca8000.midtronics.com/

NTB23-053

Service Bulletin/Repair Instructions

SILICONE-BASED LUBRICANT OR GREASE CAN DAMAGE ELECTRICAL COMPONENTS SERVICE INFORMATION Do not apply Silicone-based lubricants or grease to, or around, any interior electrical components. To avoid the risk of death or severe personal injury, do not directly spray Silicone-based lubricant or grease, or inadvertently overspray Silicone-based lubricant or grease onto any interior electrical components. These types of lubricants can be detrimental to the proper operation of electrical components.

NTB13-107F

Service Bulletin/Repair Instructions

VEHICLE KEY NOT DETECTED / AUTHENTICATED, ENGINE WILL NOT START This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB14-012I

Service Bulletin/Repair Instructions

REMOTE ENGINE START NOT WORKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB16-003C

Service Bulletin/Repair Instructions

INTELLIGENT KEY REPLACEMENT OR SWAPPING BETWEEN VEHICLES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.

NTB23-018C

Service Bulletin/Repair Instructions

SOFTWARE UPDATE FOR INFOTAINMENT ISSUES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB03-074Q

Service Bulletin/Repair Instructions

HEADLAMP, FOG LAMP, OR REAR COMBINATION LAMP FOGGING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB12-055J

Service Bulletin/Repair Instructions

CLICKING NOISE FROM FRONT OR REAR AXLE DURING TAKE-OFF/ACCELERATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB23-018B

Service Bulletin/Repair Instructions

SOFTWARE UPDATE FOR INFOTAINMENT ISSUES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB23-023

Service Bulletin/Repair Instructions

FLUID LEAK FROM THE FRONT DIFFERENTIAL CASE ACTUATOR MOTOR SERVICE INFORMATION If the front differential of an APPLIED VEHICLE has a fluid leak from the actuator motor body or threads (Figure 1), replace the actuator motor on the front differential case. DO NOT replace the front differential due to a fluid leak from the actuator motor unless there has been consequential damage due to fluid loss (bearing failure or gear noise) to the front differential.

NTB23-018A

Service Bulletin/Repair Instructions

SOFTWARE UPDATE FOR INFOTAINMENT ISSUES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB19-071C

Service Bulletin/Repair Instructions

DTC B00A0-00 STORED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB21-106A

Service Bulletin/Repair Instructions

DTC C1A17-49 OR C2580-49 STORED IN LASER/RADAR This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB10-145B

Service Bulletin/Repair Instructions

ABS/VDC CAN DIAGNOSIS INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB23-018

Service Bulletin/Repair Instructions

SOFTWARE UPDATE FOR INFOTAINMENT ISSUES SERVICE INFORMATION When diagnosing an infotainment issue or after replacement of the AV Control Unit, it is necessary to verify the current software version of the AV Control Unit to determine if a software version update is required. Use the vehicle tables in this bulletin to determine the current software version, if the AV Control Unit requires a software version update, and which procedure to use to update the AV Control Unit. The software updates in this bulletin are to address stability improvements and âbugâ fixes. IMPORTANT: If the customer is experiencing a software related concern, refer to NTB21-038 to verify if the customer concern is a hardware or software related issue. If the concern is a software related issue, review the information in this bulletin to update the AV Control Unit as needed.

NTB09-081J

Service Bulletin/Repair Instructions

WINDSHIELD CRACKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB13-028H

Service Bulletin/Repair Instructions

REMOVING FOREIGN MATERIAL FROM THE WINDOW GLASS This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB08-097K

Service Bulletin/Repair Instructions

DIAGNOSIS OF VEHICLE PULL (DRIFT) AND/OR STEERING WHEEL OFF-CENTER This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB10-126C

Service Bulletin/Repair Instructions

WHEEL BEARING COLLISION DAMAGE This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB22-101

Service Bulletin/Repair Instructions

DRIVE SHAFT BOOT SERVICE INFORMATION SERVICE INFORMATION If a Drive Shaft (Axle Shaft) Boot on an APPLIED VEHICLE is found to be leaking grease, AND There is no abnormal noise or obvious CV Joint risk due to water intrusion and/or complete grease loss, check for REPAIR KIT-DUST BOOT (CV Joint Boot Kit) availability. ï· If there is a REPAIR KIT-DUST BOOT (CV Joint Boot Kit) available for the vehicle being repaired, do NOT replace the axle. Install a new boot kit following the procedure in the ESM. o Refer to the ESM: TRANSMISSION & DRIVELINE > FRONT AXLE > REMOVAL AND INSTALLATION > FRONT DRIVE SHAFT BOOT o If the complete axle (drive shaft) is replaced when only a new boot is required, the over-repair may be charged back to the dealer. ï· If there is NOT a REPAIR KIT-DUST BOOT (CV Joint Boot Kit) available for the vehicle being repaired, refer to the ESM for further diagnostic information. IMPORTANT: When servicing vehicles with staked axle nuts, refer to NTB21-013 to prevent Drive Shaft thread damage.

NTB22-100

Service Bulletin/Repair Instructions

3G TELEMATICS HARDWARE DEACTIVATION SERVICE INFORMATION The APPLIED VEHICLES that come equipped with a factory installed SOS switch, located near the overhead map lamp, also come equipped with a wireless communication device called a Telematics Communication Unit (TCU). AT&T discontinued its U.S. 3G network coverage on February 22, 2022. As a result, automakers that utilize AT&Tâs 3G network connection, including Nissan Group, have had connectivity services affected. NissanConnectÂ® Services are no longer available on the APPLIED VEHICLES listed above.

PC864_PC854 2016

Service Bulletin/Repair Instructions

Turbo Actuator/High-Pressure Turbocharger Emission Warranty Extension Dealer Notification *****Dealer Announcement***** Nissan is committed to providing the highest levels of product quality and customer satisfaction. Therefore, Nissan is extending the emission warranty coverage on MY16 Titan XD Titan Turbo Actuator and High-Pressure Turbocharger to 10 Years or 150,000 miles, whichever occurs first. All other warranty terms, limitations, and conditions remain unchanged. Certain MY16 TITAN XD Diesel vehicles may experience issues with the Turbo Actuator or the High-Pressure Turbocharger. Over time, a solder crack may develop in the Turbo Actuator and/or carbon build-up is possible on the High-Pressure Turbocharger Compressor. The most likely conditions are a MIL-On with DTC P00AF and/or DTC P0299. These issues have no effect on vehicle safety, drivability, or fuel economy. There could be a decrease in performance if either condition were to occur. During the limited emission warranty extension period, owners are eligible for free replacement of the Turbo Actuator and High-Pressure Turbocharger if either is determined to be required by a Nissan trained technician. Owners of eligible vehicles will receive notification of this limited emission warranty extension during November 2022. ***** What Dealers Should Do ***** 1. Verify if vehicles are eligible for this Warranty Extension using the warranty extension page of Service Comm. 2. If a customer contacts the dealer with a Turbo Actuator or High-Pressure Turbocharger concern in an owned or leased vehicle, dealers should use the appropriate Technical Service Bulletin (TSB) to diagnose the root cause of the customer concern and identify the correct repair to resolve the customer concerns.

NTB22-087

Service Bulletin/Repair Instructions

NOISE AND/OR VIBRATION FROM FRONT OR REAR PROPELLER SHAFT SERVICE INFORMATION If you confirm abnormal noise and/or vibration is coming from the front or rear propeller shaft of an APPLIED VEHICLE, inspect the propeller shaft journals (U-Joints) for binding and/or abnormal noise before replacing the propeller shaft. If binding and/or abnormal noise is confirmed from the propeller shaft U-Joints, replace the propeller shaft U-Joints. Refer to the ESM for the propeller shaft U-Joint replacement procedure. NOTE: Replacement of the propeller shaft due to noise and/or vibration caused by the propeller shaft U-Joints may result in warranty charge back.

NTB12-055I

Service Bulletin/Repair Instructions

CLICKING NOISE FROM FRONT OR REAR AXLE DURING TAKE-OFF/ACCELERATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB14-012H

Service Bulletin/Repair Instructions

REMOTE ENGINE START NOT WORKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB20-068A

Service Bulletin/Repair Instructions

TRANSFER CASE SEAL SERVICE PARTS This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB19-071B

Service Bulletin/Repair Instructions

DTC B00A0-00 STORED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB22-026

Service Bulletin/Repair Instructions

SERVICE INFORMATION FOR FUEL GAUGE INACCURATE WITH DTCS STORED IN ECM SERVICE INFORMATION If a fuel level sensor has been diagnosed as sending an incorrect level signal, and one or more of the following DTCs are stored in the ECM, do not replace the entire âFuel Level Sensor Unit, Fuel Filter and Fuel Pump Assemblyâ (fuel pump assembly). The fuel level sensor can be replaced separately. ï· P0460 (FUEL LEV SEN SLOSH) ï· P0461 (FUEL LEVEL SENSOR) ï· P0462 (FUEL LEVL SEN/CIRC) ï· P0463 (FUEL LEVL SEN/CIRC) NOTE: Warranty claims referring to fuel level issues that result in the replacement of the entire fuel pump assembly will be charged back.

NTB15-049X

Service Bulletin/Repair Instructions

TELEMATICS SERVICE INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB13-027C

Service Bulletin/Repair Instructions

CAN COMMUNICATION â NETWORK DIAGNOSTIC FLOW CHART This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB13-097J

Service Bulletin/Repair Instructions

EVAP LEAK DTC P0442, P0455, P0456 INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB17-082E

Service Bulletin/Repair Instructions

DTC P0456 CAUSED BY EVAP LEAK AT VENT CONTROL VALVE O-RING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB17-045C

Service Bulletin/Repair Instructions

CLEANING FRONT OR REAR COMBINATION LAMP ASSEMBLIES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB99-001F

Service Bulletin/Repair Instructions

STRUT AND SHOCK ABSORBER REPLACEMENT GUIDELINES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB21-106

Service Bulletin/Repair Instructions

DTC C1A17-49 OR C2580-49 STORED IN LASER/RADAR SERVICE INFORMATION If DTC C1A17-49 or C2580-49 is stored in LASER/RADAR in the âPASTâ column: ï· Erase the DTC. ï· DO NOT replace any parts. If DTC C1A17-49 or C2580-49 is stored in LASER/RADAR in the "CURRENT" column, refer to the applicable ESM for instructions.

NTB18-031D

Service Bulletin/Repair Instructions

2016-2018 NISSANCONNECT NAVIGATION SYSTEM SOFTWARE UPDATE TO RESOLVE SEVERAL ISSUES This bulletin has been amended. See AMENDMENT HISTORY on page 14. Please discard previous versions of this bulletin.

NTB21-093

Service Bulletin/Repair Instructions

WATER INTRUSION INTO REAR COMBINATION LAMP CAN CAUSE MULTIPLE DTCS AND NO-START CONDITION SERVICE INFORMATION Water intrusion into one or both of the rear combination lamp assemblies can cause multiple DTCs, and possibly cause the vehicleâs engine to not start. Water intrusion into one or both rear combination lamp assemblies has been found to migrate through the harness, and can cause harness connector terminals in C1/E41 to corrode (Figure 1 on page 2). ï· Repair any damaged rear combination lamp assemblies immediately to avoid potential harness damage. Notice Harness connector terminals in C1/E41 found to be damaged through water intrusion due to a damaged rear combination lamp assembly is not warrantable.

NTB12-055H

Service Bulletin/Repair Instructions

CLICKING NOISE FROM FRONT OR REAR AXLE DURING TAKE-OFF/ACCELERATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB15-077D

Service Bulletin/Repair Instructions

SIGNAL TECH-II INTELLIGENT KEY BATTERY TEST AND SIGNAL CHECK This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB16-028D

Service Bulletin/Repair Instructions

INTELLIGENT KEY BUTTONS INOPERATIVE BUT REQUEST SWITCHES WORK This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB21-027

Service Bulletin/Repair Instructions

MIL ON WITH DTC P062F AND/OR P0603 STORED IF YOU CONFIRM The MIL is ON and DTC P062F (EEPROM) and/or P0603 (ECM BACK UP/CIRCUIT) is stored, And The customer stated the vehicle was recently started after sitting for an extended period of time (i.e., the battery voltage was low while attempting to start the engine). ACTION 1. Test the vehicleâs 12 volt battery using the Midtronics DSS-5000. Recharge or replace the battery if necessary. 2. Erase all DTCs.

NTB15-049W

Service Bulletin/Repair Instructions

TELEMATICS SERVICE INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB13-106G

Service Bulletin/Repair Instructions

CORRECT OPERATION OF AUDIO CONTROLS AND BACK-UP CAMERA REQUIRES CONFIGURATION WITH C-III PLUS This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.

NTB13-099G

Service Bulletin/Repair Instructions

AUDIO UNIT REPLACEMENT - VEHICLES WITH COLOR DISPLAY AUDIO AND NAVIGATION SYSTEM This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin

NTB15-077C

Service Bulletin/Repair Instructions

NISSAN; SIGNAL TECH-II INTELLIGENT KEY BATTERY TEST AND SIGNAL CHECK This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB17-014A

Service Bulletin/Repair Instructions

BLUETOOTH, USB, AND AUX FUNCTION DIAGNOSTIC TOOL This bulletin has been amended. See AMENDMENT HISTORY on page 3. Please discard previous versions of this bulletin.

NTB19-071A

Service Bulletin/Repair Instructions

DTC B00A0-00 STORED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB16-045B

Service Bulletin/Repair Instructions

2016-2019 TITAN AND TITAN XD; 7 SPEED A/T DTCs STORED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB99-001e

Service Bulletin/Repair Instructions

STRUT AND SHOCK ABSORBER REPLACEMENT GUIDELINES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB18-063a

Service Bulletin/Repair Instructions

2016-2018 TITAN/TITAN XD AND 2012-2018 NV1500/2500/3500; ANTENNA STANDARDIZATION This bulletin has been amended. See Amendment History on the last page. Discard all previous versions of this bulletin.

NTB20-058a

Service Bulletin/Repair Instructions

2016-2019 TITAN/TITAN XD; REAR SONAR SENSORS DO NOT DETECT OBJECTS/OBSTRUCTIONS WHEN IN REVERSE This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB15-049v

Service Bulletin/Repair Instructions

TELEMATICS SERVICE INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB20-070

Service Bulletin/Repair Instructions

2016-2019 TITAN XD DIESEL; TURBOCHARGER SERVICE INFORMATION SERVICE INFORMATION The low pressure turbocharger and the high pressure turbocharger on the APPLIED VEHICLES, listed above, are now available as separate service parts. ï· If the low pressure turbocharger on an APPLIED VEHICLE is being replaced for any reason, refer to NTB20-071 for the removal procedure, installation procedure and parts information. ï· If the high pressure turbocharger on an APPLIED VEHICLE is being replaced for any reason, refer to NTB19-017 for the removal procedure, installation procedure and parts information.

NTB20-071

Service Bulletin/Repair Instructions

2016-2019 TITAN XD DIESEL; MIL ON WITH DTC P226C STORED IF YOU CONFIRM The MIL is ON and DTC P226C (TC BOOST CONTROL SLOW RESPONSE) IS stored, And DTC P00AF (BOOST PRESSURE CONTROL) is NOT stored in the ECM, And Binding and/or resistance is observed when the rotary turbine control valve is moved from one stop to the other (full span), by hand. NOTE: Disconnect the linkage at the actuator to move the rotary control valve. ACTION Replace the low pressure turbocharger.

NTB20-068

Service Bulletin/Repair Instructions

2016-2020 TITAN/TITAN XD; TRANSFER CASE SEAL SERVICE PARTS SERVICE INFORMATION The front ouput seal, rear output seal and input seal are available as service parts (see page 2). If a transfer case is leaking from either the input or output seals, first check the fluid to confirm that it is not low, discolored, and/or has an abnormal smell. If the fluid condition indicates that the transfer case has been damaged, the transfer case should be replaced. If the fluid condition is ok, replace only the leaking seal. ï· Refer to the Electronic Service Manual (ESM) for the appropriate seal replacement: TRANSMISSION & DRIVELINE > DRIVELINE > TRANSFER: TX91A. NOTE: Over-repair of the transfer case by replacement may be grounds for warranty chargeback.

NTB19-037a

Service Bulletin/Repair Instructions

2016-2019 TITAN; MIL ON WITH DTC P0448 AND WATER IN EVAP FILTER This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB15-049u

Service Bulletin/Repair Instructions

TELEMATICS SERVICE INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

PC731 2016-17 TI

Service Bulletin/Repair Instructions

On-Board Diagnostic (OBD) Electronic Control Unit (ECU) Voluntary Emission Recall Campaign ***** Campaign Summary ***** Nissan is conducting a Voluntary Emissions Recall Campaign on 27,085 certain MY2016-17 Titan Diesel vehicles identified in Service Comm to inspect and, if necessary, reprogram the Electronic Control Unit (ECU) with countermeasure software. Nissan has determined that the subject vehicles were manufactured with an On-Board Diagnostic (OBD) calibration that may not allow the exhaust gas sensor monitors to run as intended. If an affected vehicle is not repaired, the exhaust gas sensor monitors may not run as frequently as required by regulation to determine if the sensor is performing as intended. This issue has no effect on vehicle safety, fuel economy, drivability, or performance. ***** What Dealers Should Do**** 1. Verify campaign applicability using Service Comm or DBS National Service History â Open Campaign I.D. PC731. 2. Dealers should use NTB20-030 to correct any vehicles subject to this campaign. 3. Once repaired, dealers should submit the claim, using the claims coding provided, and release the vehicle.

NTB20-030

Service Bulletin/Repair Instructions

VOLUNTARY EMISSIONS RECALL CAMPAIGN 2016-2017 TITAN XD WITH DIESEL ENGINE; ENGINE CONTROL MODULE INTRODUCTION Nissan is conducting this voluntary emissions recall campaign on certain specific model year 2016-2017 Titan XD vehicles equipped with a diesel engine. The Engine Control Module (ECM) will be inspected, and reprogrammed if it applies. This service will be performed at no charge to the customer for parts or labor. IDENTIFICATION NUMBER Nissan has assigned identification number PC731 to this campaign. This number must appear on all communication and documentation of any nature dealing with this campaign. DEALER RESPONSIBILITY It is the dealerâs responsibility to check Service COMM or Dealer Business Systems (DBS) National Service History for the campaign status on each vehicle falling within the range of this voluntary emissions recall which for any reason enters the service department. This includes vehicles purchased from private parties or presented by transient (tourist) owners and vehicles in a dealerâs inventory. Federal law requires that new vehicles in dealer inventory which are the subject of a emissions recall must be corrected prior to sale. Failure to do so can result in civil penalties and/or fines by the Environmental Protection Agency. While federal law applies only to new vehicles, Nissan strongly encourages dealers to correct any used vehicles in their inventory before they are retailed.

NTB19-011a

Service Bulletin/Repair Instructions

2016 â 2019 TITAN XD; MIL ON WITH DTC P2048 STORED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB15-049t

Service Bulletin/Repair Instructions

TELEMATICS SERVICE INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB19-004a

Service Bulletin/Repair Instructions

2015-2019 MURANO AND 2016-2019 TITAN; CLIMATE CONTROLLED SEAT INOPERATIVE This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB19-071

Service Bulletin/Repair Instructions

DTC B00A0-00 STORED IF YOU CONFIRM DTC B00A0-00 (OCCUPANT DETECTION SENSOR UNIT) is stored And OCS zero point reset cannot be performed (continued on the next page) And The following screen displays: ACTION 1. Check the Occupant Classification System (OCS) control unit using the ODS Analysis tool software. ï· Refer to SERVICE PROCEDURE on page 5. HINT: âOCSâ may also be referred to as âODSâ. 2. Perform â75-zero RESETâ.

NTB14-012e

Service Bulletin/Repair Instructions

REMOTE ENGINE START NOT WORKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB19-026a

Service Bulletin/Repair Instructions

2016 â 2018 TITAN XD; STATIC DISCHARGE FROM FUEL LINE This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB19-026

Service Bulletin/Repair Instructions

2016 - 2018 TITAN XD; STATIC DISCHARGE FROM FUEL LINE IF YOU CONFIRM There is a static discharge from the fuel line causing a click or pop noise. NOTE: Concern is more likely to: - Be heard from under the center of vehicle. - Occur more often on dry days. - Occur at regular intervals about every 30 seconds to 1 minute. ACTION Install the tether assembly as described in the SERVICE PROCEDURE starting on the next page.

NTB15-049s

Service Bulletin/Repair Instructions

TELEMATICS SERVICE INFORMATION This bulletin applies only to vehicles equipped with a Telematics Communication Unit (TCU). This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB19-049

Service Bulletin/Repair Instructions

2016-2019 TITAN/TITAN XD; WHISTLE NOISE WHEN REFUELING This bulletin applies only to vehicles equipped with a gasoline V8 engine. IF YOU CONFIRM A whistle noise is heard when refueling the vehicle. ACTION Replace the fuel tank with the new one listed in the PARTS INFORMATION section of this bulletin.

NTB17-053a

Service Bulletin/Repair Instructions

2016-2017 TITAN/TITAN XD; FAN COUPLING TICK / KNOCK IN COLD AMBIENT TEMPERATURES (32°F (0°C) OR BELOW) This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.

NTB19-037

Service Bulletin/Repair Instructions

2016-2019 TITAN; MIL ON WITH DTC P0448 AND WATER IN EVAP FILTER IF YOU CONFIRM The MIL is ON with DTC P0448 (EVAP canister vent control valve close) stored in the ECM and water is found in the EVAP filter, canister, or vent control valve ACTION Remove and replace the: - Fuel filler tube. - EVAP filter. - EVAP canister. - EVAP vent control valve. - EVAP pressure sensor. IMPORTANT: Before any parts are removed from the vehicle, note the EVAP filter orientation and hose routing (take a photo). Hose routing and EVAP filter orientation is critical and varies depending on production date.

NTB17-010a

Service Bulletin/Repair Instructions

2016 ? 2019 TITAN AND TITAN XD; STEP RAIL END CAP CHROME TRIM AVAILABLE AS SEPARATE PART This bulletin applies only to Crew Cab models. This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

NTB16-037e

Service Bulletin/Repair Instructions

2016 TITAN XD; MIL ON WITH ENGINE DTCs STORED AND/OR IDLE FLUCTUATION This bulletin applies only to vehicles equipped with a Cummins 5.0L V8 Diesel engine. This bulletin has been amended. See Amendment History on the last page. Please discard previous versions of this bulletin.

NTB19-011

Service Bulletin/Repair Instructions

2016 ? 2018 TITAN XD; MIL ON WITH DTC P2048 STORED This bulletin applies only to vehicles equipped with a Cummins 5.0L V8 Diesel engine. IF YOU CONFIRM The MIL is ON and DTC P2048 (REDUCTANT INJECTION VALVE CIRCUIT LOW 1/1) is stored. ACTION Reprogram the ECM per the SERVICE PROCEDURE in this bulletin. - Refer to SERVICE PROCEDURE on the next page to confirm if reprogramming is needed. - Save Computer Data with CONSULT-III plus (C-III plus). - If this bulletin applies, continue with ECM Reprogramming procedure. - Write Saved Data with CONSULT-III plus.

NTB19-017

Service Bulletin/Repair Instructions

2016-2019 TITAN XD DIESEL; MIL ON WITH DTC P0299 FOR BOOST PRESSURE This bulletin applies only to vehicles equipped with a Cummins 5.0L V8 Diesel engine. IF YOU CONFIRM The MIL is ON with DTC P0299 (BOOST PRESSURE) stored And - The engine air cleaner box and air filter: - Are free from debris - Are not damaged or have any restrictions - The engine charge air cooler tube clamps are tight and tubes are free from leaks at the following locations: - The turbocharger compressor outlet - The charge air cooler inlet - The charge air cooler outlet - The intake manifold inlet - The Boost Pressure Absolute is within +/- 1.5 PSI of ambient air pressure with ignition ON and engine OFF (observed in Data Monitor). ACTION Refer to Repair Overview on page 2.

NTB19-013

Service Bulletin/Repair Instructions

2016-2018 TITAN/TITAN XD WITH AUTO A/C; VAST TEMPERATURE DIFFERENCE BETWEEN 61°F & 62°F SETTINGS This bulletin applies only to vehicles equipped with auto A/C. IF YOU CONFIRM The customer states there is a significant difference in vent temperature between auto A/C settings of 61°F and 62°F. ACTION 1. Check the A/C auto amp?s current part number. 2. If the current part number matches one listed in Table A (see page 6), reprogram the A/C auto amp.

NTB19-010

Service Bulletin/Repair Instructions

2016 - 2018 TITAN XD; DEF SYSTEM PARTS AVAILABILITY This bulletin applies only to vehicles equipped with a Cummins 5.0L V8 diesel engine. SERVICE INFORMATION When diagnosing any Diesel Exhaust Fluid (DEF) system component, refer to Table A below. These parts are now available separately. Do not replace the entire DEF tank assembly if the required part is shown in Table A.

NTB13-097g

Service Bulletin/Repair Instructions

ALL MODEL YEAR 2012 AND NEWER NISSAN VEHICLES; EVAP LEAK DTC P0442, P0455, P0456 INFORMATION This bulletin does NOT apply to LEAF vehicles and Titan XD vehicles with V8 diesel engine. This bulletin has been amended. See Amendment History on the last page. Please discard previous versions of this bulletin.

NTB15-049r

Service Bulletin/Repair Instructions

NTB17-082b

Service Bulletin/Repair Instructions

NISSAN; DTC P0456 CAUSED BY EVAP LEAK AT VENT CONTROL VALVE O-RING This bulletin does NOT apply to LEAF vehicles and Titan XD vehicles with V8 diesel engine. This bulletin has been amended. See Amendment History on the last page. Please discard previous versions of this bulletin.

NTB19-007

Service Bulletin/Repair Instructions

2016-2019 TITAN XD DIESEL; FUEL FILTER MAINTENANCE This bulletin applies only to vehicles equipped with a Cummins 5.0L V8 diesel engine. SERVICE INFORMATION The Stage 1 and Stage 2 fuel filters must be replaced every 10,000 miles or a restriction may develop. DTCs P008A, P00C6, P0087 and/or a whining noise from the Stage 1 Fuel Filter Module may be present due to a restriction in the Stage 1 and/or Stage 2 fuel filters. NOTE: An inoperable or whining Stage 1 Fuel Filter Module that has not had the fuel filters regularly replaced as per the Owner?s Manual Maintenance schedule is not a warrantable repair. Before proceeding with any fuel system restriction diagnosis: - Confirm that both of the vehicle?s Stage 1 and Stage 2 fuel filters have been replaced at the correct service intervals, as per the Owner?s Manual Maintenance schedule. IMPORTANT: Warranty claim submissions for a Stage 1 Fuel Filter module will be denied if the Stage 1 and/or Stage 2 fuel filters have not been replaced per the Owner's Manual maintenance schedule.

NTB19-004

Service Bulletin/Repair Instructions

2015-2019 MURANO AND 2016-2019 TITAN; CLIMATE CONTROLLED SEAT INOPERATIVE IF YOU CONFIRM The driver or passenger side climate controlled seat: - Heating and cooling features do not operate And - The harness connector or control unit of the climate controlled seat appears as shown in Figure 3 or Figure 5. ACTION Perform the following to the affected seat: A. Replace the climate controlled seat control unit. B. Drill a hole for the new harness clip. C. Replace the harness connector of the climate controlled seat control unit. IMPORTANT: The purpose of ACTION (above) is to give you a quick idea of the work you will be performing. You MUST closely follow the entire SERVICE PROCEDURE as it contains information that is essential to successfully completing this repair.

NTB19-005

Service Bulletin/Repair Instructions

2016-2018 TITAN/TITAN XD; VISIBLE VIBRATION IN FRONT PASSENGER SEAT AT 60-80 MPH WHEN UNOCCUPIED IF YOU CONFIRM The front passenger seat has a visible vibration/movement that only occurs at speeds between 60 mph and 80 mph And Vibration/movement can be reproduced while driving on smooth roads (vibration/movement not caused by road surface) And All tires are in balance and road force vibration is within specifications (see NTB11-062). ACTION Replace the front passenger seatback assembly and front passenger headrest. IMPORTANT: The purpose of ACTION (above) is to give you a quick idea of the work you will be performing. You MUST closely follow the entire SERVICE PROCEDURE as it contains information that is essential to successfully completing this repair.

NTB19-003

Service Bulletin/Repair Instructions

2016-2017 TITAN XD DIESEL; HIGH PRESSURE FUEL INJECTOR SUPPLY LINE TORQUE CHANGE This bulletin applies only to vehicles equipped with a Cummins 5.0L V8 diesel engine. SERVICE INFORMATION For the Applied Vehicles, the high pressure fuel injector supply line nut torque specifiction listed in the Electronic Service Manual (ESM) has been revised. Until the ESMs are updated, use the torque specification shown below.

NTB16-125a

Service Bulletin/Repair Instructions

2016-2019 TITAN XD; DIESEL FUEL DEF CONTAMINATION This bulletin applies only to vehicles equipped with a Cummins 5.0L V8 Diesel engine. This bulletin has been amended. See Amendment History on the last page. Please discard previous versions of this bulletin.

NTB17-030a

Service Bulletin/Repair Instructions

NISSAN; FUEL TANK IS EXTREMELY DIFFICULT TO FILL This bulletin applies to Titan XD vehicles with a gas engine. The update below was sent out to Regions and Dealers in August of this year. We are re-circulating this update to make regional and dealer personnel aware that we are re-notifying customers at this time.

Revision 1-NEVAP

Service Bulletin/Repair Instructions

OBD II EVAP Tube Warranty Enhancement The update below was sent out to Regions and Dealers in August of this year. We are re-circulating this update to make regional and dealer personnel aware that we are re-notifying customers at this time.

NTB18-080

Service Bulletin/Repair Instructions

AIR BAG WARNING LIGHT FLASHING INDICATING SYSTEM DIAGNOSTIC MODE IF YOU CONFIRM The air bag warning light is flashing slowly (repeating 2 seconds ON, 2 seconds OFF). NOTE: If this should occur, the Air Bag Diagnosis Sensor Unit is in Diagnostic Mode and needs to be returned to User Mode. ACTION 1. Use CONSULT-III plus to check for Air Bag DTCs and perform repairs as needed. 2. Return the Air Bag Diagnosis Sensor Unit to User Mode.

NTB15-077b

Service Bulletin/Repair Instructions

NISSAN; SIGNAL TECH-II INTELLIGENT KEY BATTERY TEST AND SIGNAL CHECK This bulletin has been amended. See Amendment History on the last page. Please discard previous versions of this bulletin.

NTB16-102a

Service Bulletin/Repair Instructions

2016 TITAN XD; BUZZ NOISE FROM SUBWOOFER This bulletin has been amended. The PARTS INFORMATION section has been revised. No other changes have been made. Please discard previous versions of this bulletin.

NTB18-063

Service Bulletin/Repair Instructions

2016-2018 TITAN/TITAN XD AND 2012-2018 NV1500/2500/3500; ANTENNA STANDARDIZATION SERVICE INFORMATION For the applied vehicles, the replacement antenna base and antenna mast styles have changed to a new style, shown in Figure 1. The old style has been discontinued. If for any reason the old style antenna base needs to be replaced, both the base and the mast must be replaced as a set with the new style shown in Figure 1. If the vehicle still has the old style antenna base, as shown in Figure 2, and only the mast is damaged, a replacement antenna mast can be ordered.

NTB17-060b

Service Bulletin/Repair Instructions

2016-2018 TITAN XD; DTC P207F AND DEF SYSTEM ERROR IS DISPLAYED ON THE VEHICLE INFORMATION DISPLAY This bulletin applies only to vehicles equipped with a Cummins 5.0L V8 Diesel engine. This bulletin has been amended. The Applied Vehicles section, Table A on page 7, and the DTC Confirmation procedure have been revised. No other changes have been made. Please discard previous versions of this bulletin.

NTB15-049q

Service Bulletin/Repair Instructions

TELEMATICS SERVICE INFORMATION This bulletin applies only to vehicles equipped with a Telematics Communication Unit (TCU). This bulletin has been amended to add a Required Actions by Model and Year table on page 2, a Check OFF Sheet on page 21 and to reorganize the information throughout. It is necessary for you to read this revised procedure to properly perform this Service Information. Please discard previous versions of this bulletin.

NTB18-024a

Service Bulletin/Repair Instructions

2016-2019 TITAN XD; STAGE 1 AND STAGE 2 FUEL FILTER ELEMENT REPLACEMENT This bulletin applies only to vehicles equipped with a Cummins 5.0L V8 Diesel engine. This bulletin has been amended. Changes were made on page 4, 6, and 12. Please discard previous versions of this bulletin.

NTB15-049p

Service Bulletin/Repair Instructions

TELEMATICS SERVICE INFORMATION This bulletin only applies to vehicles equipped with a Telematics Communication Unit (TCU). This bulletin has been amended. Changes have been made to page 10 for 2018 Armada. Please discard previous versions of this bulletin.

NTB18-017b

Service Bulletin/Repair Instructions

NISSAN; SERVICE INFORMATION FOR DTCS B2EF0 AND B130C This bulletin only applies to vehicles equipped with a Telematics Communication Unit (TCU). This bulletin has been amended. APPLIED VEHICLES has been updated. On page 2, the procedural steps under DTC B130C have been revised. Discard all previous versions of this bulletin.

NTB10-104c

Service Bulletin/Repair Instructions

TITAN, ARMADA, NV; ENGINE OIL LEAK AT RIGHT SIDE BLOCK BALL PLUG This bulletin has been amended. The APPLIED VEHICLES section has been updated. No other changes have been made. Please discard all previous versions of this bulletin.

NTB18-046a

Service Bulletin/Repair Instructions

2016-2018 TITAN XD DIESEL; AIR CONDITIONING BLOWS HOT AIR AFTER EXTENDED IDLING OVER 100°F This bulletin applies only to vehicles equipped with a Cummins 5.0L V8 Diesel engine. This bulletin has been amended to change the Classification number. No other changes have been made. Please discard previous versions of this bulletin.

NTB18-031b

Service Bulletin/Repair Instructions

2016-2018 NISSAN CONNECT NAVIGATION SYSTEM SOFTWARE UPDATE TO RESOLVE SEVERAL ISSUES This bulletin has been amended. The IF YOU CONFIRM section and software number has changed. No other changes have been made. Please discard previous versions of this bulletin.

NTB18-046

Service Bulletin/Repair Instructions

2016-2018 TITAN XD DIESEL; AIR CONDITIONING BLOWS HOT AIR AFTER EXTENDED IDLING OVER 100°F This bulletin applies only to vehicles equipped with a Cummins 5.0L V8 Diesel engine. IF YOU CONFIRM Hot air starts to blow from the dash vents while the Air Conditioning is ON, under the following conditions: - After the engine has idled for an extended period with the vehicle in Drive (D-range). And - Ambient temperature outside the vehicle is 100°F (37.8°C) or more. ACTION 1. Save Computer Data with CONSULT-III plus (C-III plus). 2. At step 6 of the reprogramming procedure, confirm this bulletin applies to the vehicle you are working on. 3. If this bulletin applies, continue with the reprogramming procedure. 4. Write Saved Data with CONSULT-III plus.

NTB18-043

Service Bulletin/Repair Instructions

HEADLIGHT SYSTEM ERROR DIAGNOSTIC INFORMATION SERVICE INFORMATION - When diagnosing a Headlight System Error warning, and - Both headlamps are visually working correctly, - It may be difficult to determine the exact cause. - Use the information in this bulletin as an aid, along with the Electronic Service Manual (ESM), to isolate the root cause and fix it right the first time.

NTB18-031a

Service Bulletin/Repair Instructions

2016-2018 NISSAN CONNECT NAVIGATION SYSTEM SOFTWARE UPDATE TO RESOLVE SEVERAL ISSUES This bulletin applies only to vehicles equipped with navigation system. This bulletin has been amended to correct Bosch contact information on page 2. No other changes have been made. Please discard previous versions of this bulletin.

NTB18-037

Service Bulletin/Repair Instructions

2016 TITAN XD; MIL ON WITH DTC P0420 IF YOU CONFIRM The MIL is ?ON? with DTC P0420 (Catalyst System Efficiency Below Threshhold Bank 1), AND There are no drivability issues. ACTION 1. Save Computer Data with CONSULT-III plus (C-III plus). 2. At step 6 of the reprogramming procedure, confirm this bulletin applies to the vehicle you are working on. 3. If this bulletin applies, continue with reprogramming. 4. Write Saved Data with C-III plus.

NTB16-100c

Service Bulletin/Repair Instructions

2016-2017 NISSAN CONNECT NAVIGATION SYSTEM SOFTWARE UPDATE This bulletin applies only to vehicles equipped with navigation system. This bulletin has been superseded to NTB18-031. Please discard all previous versions of this bulletin.

NTB18-031

Service Bulletin/Repair Instructions

2016-2018 NISSAN CONNECT NAVIGATION SYSTEM SOFTWARE UPDATE TO RESOLVE SEVERAL ISSUES This bulletin applies only to vehicles equipped with navigation system. IF YOU CONFIRM One or more of the following is occurring: - The navigation unit intermittently reboots: - At random or while listening to SXM or on a Bluetooth hands-free phone call. - Loud booming noise from speakers while on a Bluetooth hands-free call. - Navigation unit screen illumination does not change at night as designed. - AM/FM signal strength issues. - A status message ?Voice Recognition is initializing, please wait? is displayed when pressing the voice recognition button 2-3 minutes after the ignition is first turned ON. NOTE: If the message is displayed within the first 2-3 minutes this is normal. The voice recognition is loading phonebook contacts into its system. AND - The Software version has been confirmed as ?needs update? (refer to page 4). ACTION - Perform the SERVICE PROCEDURE starting on page 3 and reprogram the Navigation system with USB memory stick shown below.

NTB03-074m

Service Bulletin/Repair Instructions

FOG LAMP AND/OR HEADLAMP FOGGING This bulletin has been amended to add Fog Lamps and modify one step in the flow chart on page 3. No other changes have been made. Please discard previous versions of this bulletin.

NTB16-018c

Service Bulletin/Repair Instructions

MIL ON WITH P0603 STORED FOR ECM BACK UP CIRCUIT This bulletin does NOT apply to Titan equipped with Cummins V8 Diesel engine. This bulletin has been amended to add a NOTE in the Applied Vehicles. No other changes have been made. Please discard previous versions of this bulletin.

NTB13-107b

Service Bulletin/Repair Instructions

INTELLIGENT KEY NOT DETECTED / ENGINE WILL NOT START This bulletin has been amended to update the Applied Vehicles. No other changes were made. Please discard previous versions of this bulletin.

NTB18-017a

Service Bulletin/Repair Instructions

NISSAN; SERVICE INFORMATION FOR DTCS B2EF0 AND B130C This bulletin applies only to vehicles equipped with Telematics. This bulletin has been amended. APPLIED VEHICLES was updated and a DTC listed in the SERVICE INFORMATION was corrected. No other changes have been made. Discard all previous versions of this bulletin.

NTB11-044c

Service Bulletin/Repair Instructions

WHEEL BALANCING SERVICE INFORMATION This bulletin has been amended. The publication date has been revised to include the latest models and model years. No other changes have been made. Please discard previous versions of this bulletin.

NTB18-024

Service Bulletin/Repair Instructions

2016-2018 TITAN XD; STAGE 1 AND STAGE 2 FUEL FILTER REPLACEMENT SERVICE INFORMATION When replacing the Stage 1 or Stage 2 fuel filters, it is important not to damage the new fuel filters, inner seals, or O-rings. Refer to the Service Procedure section of this bulletin or the Electronic Service Manual (ESM) ENGINE> FUEL SYSTEM> CUMMINS 5.0L> REMOVAL AND INSTALLATION to ensure the filters are being replaced correctly. P008A LOW FUEL PRESSURE CONTROL SYSTEM and/or a no start condition may occur if the procedure is not followed properly.

NTB18-017

Service Bulletin/Repair Instructions

NISSAN; SERVICE INFORMATION FOR DTCS B2EF0 AND B130C This bulletin applies only to vehicles equipped with Telematics. SERVICE INFORMATION Diagnostic information in the Electronic Service Manuals (ESM) for the following DTCs may be missing or incorrect: -B2EF0 ? INTERNAL BATTERY (CIRC VOLT BELOW THRESHOLD) -B130C ? TCU (Telematics Control Unit) PAIRING ERROR If one of these DTCs is stored, follow the steps listed below along with the Electronic Service Manual (ESM) to compete the required repairs. DTC B2FE0 ? INTERNAL BATTERY (CIRC VOLT BELOW THRESHOLD): 1. Start the engine and let it idle for 30 minutes (to allow charging of the TCU internal battery). -2018 LEAF only: Put the vehicle in Ready to Drive mode (depress the brake pedal and depress the power [?ignition?] switch) for 30 minutes. 2. Verify the DTC can be erased. 3. If the DTC will not erase, replace the TCU. DTC B130C: 1. Collect all keys, and then re-register them to the vehicle. 2. Verify the DTC can be erased. 3. If the DTC will not erase, replace the TCU. NOTE: The related Electronic Service Manuals (ESM) will be updated at a later date. CLAIMS INFORMATION Refer to the current Nissan Warranty Flat Rate Manual and submit a claim for the repairs performed.

NTB15-049o

Service Bulletin/Repair Instructions

TELEMATICS SERVICE INFORMATION This bulletin applies only to vehicles equipped with a Telematics Communication Unit (TCU). This bulletin has been amended. Changes have been made throughout. It is necessary to read the revised procedure(s) in entirety to properly perform the action(s). Please discard previous versions of this bulletin.

NTB18-015

Service Bulletin/Repair Instructions

2016-2018 TITAN XD; VEHICLE WILL NOT MOVE AND/OR A/T OIL TEMP LIGHT FLASHING This bulletin applies only to vehicles equipped with a Cummins 5.0L V8 Diesel engine. IF YOU CONFIRM The customer reported the following: While driving in conditions where wheel slip can occur (such as dirt, sand, mud, snow/ice, etc.), or while driving/sitting in traffic at slow speeds or idle: -The red A/T Oil Temp lamp began flashing, And/or -Vehicle would not move (the engine felt like it had no power), And -Vehicle operation returned to normal when the engine/transmission was allowed to cool. ACTION 1. Compare the vehicle?s current TCM part number to the part number listed in Table A on page 7. 2. If the current TCM part number matches a part number listed in Table A, follow the instructions in Table A.

NTB17-116a

Service Bulletin/Repair Instructions

2016-2017 TITAN AND TITAN XD; EXCESSIVE VENT TEMPERATURE DIFFERENCE IN DUAL CLIMATE CONTROL MODE WITH THE SAME TEMPERATURE SETTING This bulletin applies only to vehicles equipped with dual climate control air conditioning. This bulletin has been amended. APPLIED VINs and DATES have been added, and ACTION has been edited. No other changes have been made. Discard all previous versions of this bulletin.

NTB17-109a

Service Bulletin/Repair Instructions

2016 - 2018 TITAN AND TITAN XD; CLIMATE CONTROLLED HEATED AND COOLED SEATS POOR OR NO OPERATION This bulletin applies only to vehicles equipped with climate controlled seats. This bulletin has been amended. The APPLIED VEHICLES section and pages 17 and 18 have changed. No other changes have been made. Please discard previous versions of this bulletin.

NTB16-056b

Service Bulletin/Repair Instructions

2016-2018 TITAN XD; EXHAUST SMELL INSIDE VEHICLE WHEN HVAC IS ON FRESH AIR This bulletin applies only to vehicles equipped with a Cummins Diesel engine. This bulletin has been amended to update Applied Vehicles, remove the installation of a micro filter and to add a reprogramming procedure. No other changes have been made. Please discard previous versions of this bulletin.

NTB17-060a

Service Bulletin/Repair Instructions

2016-2017 TITAN XD; DTC P207F AND DEF SYSTEM ERROR IS DISPLAYED ON THE VEHICLE INFORMATION DISPLAY This bulletin applies to vehicles equipped with a Cummins 5.0L V8 Diesel engine. This bulletin has been amended. The Title and all sections on page 1 have been updated. Table A has also been updated. Please discard previous versions of this bulletin.

NTB18-005

Service Bulletin/Repair Instructions

2016-2017 TITAN XD WITH CUMMINS 5.0L; IDLE FLUCTUATION DURING LOW TEMPERATURE WARM-UP This bulletin applies to vehicles equipped with a Cummins 5.0L V8 Diesel engine. IF YOU CONFIRM An applied vehicle?s idle fluctuates after starting when: - The coolant temperature is between 68°F (20°C) and 104°F (40°C) and - The vehicle is not moving (0 MPH). NOTE: This incident may continue until the coolant temperature reaches 104°F (40°C). ACTION 1. Save Computer Data with CONSULT-III plus (C-III plus). 2. At step 6 of the reprogramming procedure, confirm this bulletin applies to the vehicle you are working on. 3. If this bulletin applies, continue with reprogramming procedure. 4. Write Saved Data with CONSULT-III plus.

NTB17-056a

Service Bulletin/Repair Instructions

2016-2018 TITAN AND TITAN XD; DOOR WILL NOT OPEN OR DOOR WILL NOT LATCH This bulletin has been amended. The APPLIED VEHICLES have been updated and the SERVICE PROCEDURE now includes the addition of foam to the outside handle bracket. Please discard previous versions of this bulletin.

NTB15-049n

Service Bulletin/Repair Instructions

TELEMATICS SERVICE INFORMATION This bulletin applies to vehicles equipped with a TCU (Telematics Communication Unit). This bulletin has been amended. A correction was made to the Service Procedure on page 23. No other changes were made. Please discard previous versions of this bulletin.

PC604 2016-17

Service Bulletin/Repair Instructions

Transmission Control Module Reprogram ***** Quality Action Summary ***** Nissan is conducting a dealer inventory quality action to reprogram and, if necessary calibrate, the Transmission Control Module (TCM) on specific MY2016-17 Titan XD (A61) vehicles identified in SERVICE COMM and National Service History ? Open Campaigns. These vehicles are either currently in dealer inventory or assigned and in transit to the dealer. The software update will prevent one or more of the following concerns: - Transmission shift shock when accelerating enough to create a 7 3 downshift - Engine RPM fluctuation while driving at a steady speed - Lack of power under light acceleration at low speeds (may be described as hesitation; feeling like the transmission is in too high of a gear) ***** What Dealers Should Do ***** 1. Verify if vehicles currently in dealer inventory are affected by using Service Comm or National Service History ? Open Campaign I.D. PC604. - New vehicles in dealer inventory can also be identified using DBS (Sales-> Vehicle Inventory, and filter by Open Campaign). - Refer to NPSB 15-460 for additional information - Please continue to check newly arriving inventory for campaign applicability. 2. Use the attached procedure to reprogram the TCM and, if applicable, the ECM. - If reprogramming issues arise, use CONSULT III Software version 73.10 - Use the following claims information for vehicles identified in Service Comm or DBS National Service History ? Open Campaigns ID PC604 3. Dealers are requested to remedy any affected vehicle in dealer new inventory to ensure customer satisfaction. Thank you for your prompt attention to this matter. NISSAN NORTH AMERICA, INC. Aftersales DIVISION

NTB17-122

Service Bulletin/Repair Instructions

2016 ? 2017 TITAN XD DIESEL; BLOCK HEATER INOPERATIVE This bulletin applies to vehicles equipped with a Cummins (5.0L V8) Diesel engine only. IF YOU CONFIRM The coolant heater (block heater) needs to be replaced based on the Electronic Service Manual (ESM) inspection, and The vehicle is currently equipped with a coolant heater (with attached cord) located in the front engine cover. NOTE: - This bulletin does not apply if the vehicle is equipped with a coolant heater located in the water inlet at the lower radiator hose. - Refer to the ESM, section CO ? Engine Cooling System, for coolant heater operation and inspection information. ACTION 1. Use the Service Procedure in this bulletin to install a new coolant heater, locating it in the water inlet at the lower radiator hose. 2. Cut the cord to the original coolant heater.

NTB17-116

Service Bulletin/Repair Instructions

2016-2017 TITAN AND TITAN XD; EXCESSIVE VENT TEMPERATURE DIFFERENCE IN DUAL CLIMATE CONTROL MODE WITH THE SAME TEMPERATURE SETTING This bulletin applies to vehicles with dual climate control air conditioning. IF YOU CONFIRM With the HVAC system of an applied vehicle set in dual climate control mode and both driver and passenger sides are set at the same temperature: A. Temperature set for cool air: The outlet temperature of the driver side vents are warmer by 10°F or more than the passenger side vent temperatures OR B. Temperature set for warm air: The outlet temperature of the passenger side vents are cooler by 10°F or more than the driver side vent temperatures. ACTION 1. If A above is occurring: Replace only the driver side air mix door motor (see Parts Information). - Refer to the Electronic Service Manual (ESM), section HAC-Heater & Air Conditioning Control System, for driver air mix door motor removal and installation. 2. If B above is occurring: Replace only the passenger side air mix door motor (see Parts Information). - Refer to the Electronic Service Manual (ESM), section HAC-Heater & Air Conditioning Control System, for passenger air mix door motor removal and installation.

NTB17-016e

Service Bulletin/Repair Instructions

ARMADA, TITAN AND TITAN XD; SHIFT SHOCK, LACK OF POWER, AND/OR RPM FLUCTUATES This bulletin applies to vehicles with a gasoline V8 engine only. This bulletin has been amended to add Armada to the Applied Vehicles. No other changes have been made. Please discard previous versions of this bulletin.

NTB15-049m

Service Bulletin/Repair Instructions

TELEMATICS SERVICE INFORMATION This bulletin applies to vehicles that are equipped with a wireless communication device called a Telematics Communication Unit (TCU). This bulletin has been amended. Changes have been made throughout. You must read the entire bulletin to understand all the changed information. Please discard previous versions of this bulletin.

NTB17-016d

Service Bulletin/Repair Instructions

2016 - 2017 TITAN AND TITAN XD; SHIFT SHOCK, LACK OF POWER, AND/OR RPM FLUCTUATES This bulletin applies to vehicles with a gasoline V8 engine only. This bulletin has been changed throughout. You must read the entire bulletin to properly perform this repair. Please discard previous versions of this bulletin.

NTB17-031a

Service Bulletin/Repair Instructions

2016 - 2017 TITAN XD; COOLANT HEATER (ENGINE BLOCK HEATER) INSTALLATION This bulletin applies to vehicles with a Cummins (5.0L V8) Diesel engine only. This bulletin has been amended. Substantial changes have been made throughout the body of the bulletin. Please discard all previous versions of this bulletin.

PC594 2016-17

Service Bulletin/Repair Instructions

Fuel Tank Breather Tube Dealer Inventory ***** Detailed Information ***** Nissan is conducting a dealer inventory quality action to inspect the routing of the fuel tank breather tube on approximately 4,288 specific MY2016-17 Titan XD (A61D) vehicles. During vehicle assembly, certain plant operator technicians may not have removed the temporary fuel tank breather tube cap, and may not have correctly affixed the tube to the bed rail. No parts are required for this inspection. ***** What Dealers Should Do ***** 1. Verify if vehicles currently in new dealer inventory are affected by this quality action using Service Comm or DBS National Service History - Open Campaign I.D. PC594 - New vehicles in dealer inventory can also be identified using DCS (Sales-> Vehicle Inventory, and filter by Open Campaign). i. Refer to NPSB 15-460 for additional information - Please continue to check newly arriving inventory for campaign applicability. 2. Use the attached procedure to inspect the vehicle. - If the fuel tank breather tube is routed correctly, file a claim for the inspection. - If the fuel tank breather tube is not routed correctly, provide the requested information in an email to nnafqasupport@nissan-usa.com and await further instruction. Instructions and claims information will be provided within 48 hours. 3. Dealers are requested to inspect any affected vehicle in dealer new or pre-owned inventory to ensure customer satisfaction.

NTB17-109

Service Bulletin/Repair Instructions

2016 - 2017 TITAN AND TITAN XD; CLIMATE CONTROLLED HEATED AND COOLED SEATS POOR OR NO OPERATION This bulletin applies to Titan and Titan XD vehicles equipped with climate controlled seats. IF YOU CONFIRM The Climate Controlled (Heated and Cooled) seats do not heat or cool well, or do not work at all. NOTE: This issue, if it should occur, may occur on only the driver seat, or only the front passenger seat, or both front seats. ACTION Refer to the Repair Overview flow chart on page 2.

NTB16-036b

Service Bulletin/Repair Instructions

2016-2017 TITAN XD; COLD WEATHER STARTING TIPS This bulletin has been amended. The Applied Vehicles section has been revised. No other changed have been made. Please discard previous versions of this bulletin.

NTB15-049L

Service Bulletin/Repair Instructions

TELEMATICS SERVICE INFORMATION This bulletin applies to vehicles equipped with a Telematics Communication Unit (TCU). This bulletin has been amended. Information for several 2018 models has been added. No other changes have been made. Please discard previous versions of this bulletin.

NTB11-044b

Service Bulletin/Repair Instructions

NTB17-069b

Service Bulletin/Repair Instructions

2016-2017 TITAN AND TITAN XD; NOISE FROM REAR PARKING BRAKES This bulletin has been amended to correct the Parts Information table. No other changes have been made. Please discard all previous versions of this bulletin.

NTB15-049k

Service Bulletin/Repair Instructions

TELEMATICS SERVICE INFORMATION This bulletin has been amended. The Applied Vehicles section has been revised and TCU Configuration section has been added. No other changes have been made. Please discard previous versions of this bulletin.

NTB17-089a

Service Bulletin/Repair Instructions

2016-2017 TITAN/TITAN XD; SHUDDER/CHATTER WHEN ACCELERATING FROM A STOP This bulletin has been amended to correct the Parts Information. Please discard all previous versions of this bulletin.

NTB17-082a

Service Bulletin/Repair Instructions

NISSAN; DTC P0456 CAUSED BY EVAP LEAK AT VENT CONTROL VALVE O-RING This bulletin has been amended. The APPLIED VEHICLES and CLAIMS INFORMATION sections have been revised. No other changes have been made. Please discard previous versions of this bulletin.

NTB17-016c

Service Bulletin/Repair Instructions

ARMADA, NV, TITAN, AND TITAN XD; 7-3 DOWN SHIFT SHOCK AND/OR LACK OF POWER/HESITATION This bulletin applies only to vehicles with a V8 gasoline engine. This bulletin has been amended throughout. Discard all previous versions of this bulletin.

NTB17-008b

Service Bulletin/Repair Instructions

NISSAN; OIL LEAKING AROUND VALVE TIMING CONTROL SOLENOID VALVE This bulletin applies only to Maxima, Quest, Altima Coupe, Altima Sedan, Pathfinder and Murano vehicles with a 6-cylinder engine and Titan/Titan XD vehicles with a V8 gasoline engine. This bulletin has been amended. The PARTS INFORMATION section has been revised. No other changes have been made. Please discard previous versions of this bulletin.

NTB17-069a

Service Bulletin/Repair Instructions

2016-2017 TITAN AND TITAN XD; NOISE FROM REAR PARKING BRAKES This bulletin has been amended to update the applied VIN and date information. Please discard all previous versions of this bulletin.

NTB17-089

Service Bulletin/Repair Instructions

2016-2017 TITAN/TITAN XD; SHUDDER/CHATTER WHEN ACCELERATING FROM A STOP IF YOU CONFIRM - Shudder/chatter is present during moderate to hard acceleration at speeds less than 25 mph. And - Does not occur at speeds above 25 mph. - May be worse when towing a trailer. ACTION Refer to the Repair Overview on page 2 for model specific Actions.

NTB17-086

Service Bulletin/Repair Instructions

2016 ? 2017 TITAN AND TITAN XD IGNITION WILL NOT TURN OFF This bulletin applies to vehicles not equipped with remote start. IF YOU CONFIRM While driving, the ?Key System Error? warning displays, and When parking the vehicle and pushing the Start/Stop switch, the ignition/engine does not turn OFF, and The connector cap for the hood switch harness connector (connector E94) is missing or damaged. NOTE: Refer to Figures A and B on the next page for examples of missing and damaged connector cap. ACTION Replace the hood switch harness connector (connector E94) with the new one (Service Kit) listed in the Parts Information.

NTB17-082

Service Bulletin/Repair Instructions

NISSAN; DTC P0456 CAUSED BY EVAP LEAK AT VENT CONTROL VALVE O-RING IF YOU CONFIRM The MIL is ON in an APPLIED VEHICLE with DTC P0456 (EVAP VERY SML LEAK) AND - DTC P0456 is not caused by a loose fuel fill cap (refer to NTB13-097). - An EVAP leak has been detected where the vent control valve mounts to the canister. - The vent control valve O-ring seal is determined to be the cause. ACTION 1. DO NOT REPLACE the vent control valve. 2. Replace the vent control valve O-ring seal (O-ring). - Refer to SERVICE PROCEDURE on page 2.

NTB16-068c

Service Bulletin/Repair Instructions

2016-2017 TITAN XD; TRANSMISSION SHIFT QUALITY ISSUES This bulletin applies only to vehicles equipped with a Cummins 5.0L V8 Diesel engine. IF YOU CONFIRM Any of the following issues: - When cold (transmission fluid below 140°F [60°C]), there is an engine RPM rise (200 to 500 RPM flare) during the 1-2 shift, 2-3 shift, and/or the 3-4 shift. - While slowing to a stop, a 2-1 down shift bump is felt just before stopping. - Harsh up-shifts. - Shift shock when lifting your foot from the accelerator. - Gear hunting while driving in city traffic. ACTION 1. Compare the vehicle?s current TCM part number to the part number listed in Table A on page 7. - If the current TCM part number matches a part number listed in Table A, follow the instructions in Table A. 2. Save computer data with CONSULT-III plus (C-III plus). 3. Compare the vehicle?s current ECM part number to the part number listed in Table B on page 30. - If the current ECM part number matches a part number listed in Table B, reprogram the ECM. - Write saved data. IMPORTANT: The purpose of ACTION (above) is to give you a quick idea of the work you will be performing. You MUST closely follow the entire SERVICE PROCEDURE as it contains information that is essential to successfully completing this repair.

NTB17-046a

Service Bulletin/Repair Instructions

2016-2017 TITAN AND TITAN XD; A/C COMPRESSOR SERVICE INFORMATION This bulletin has been amended. The Title and APPLIED VEHICLES section have been revised. No other changes have been made. Please discard previous versions of this bulletin.

NTB17-069

Service Bulletin/Repair Instructions

2016-2017 TITAN AND TITAN XD; NOISE FROM REAR PARKING BRAKES IF YOU CONFIRM The rear parking brake shoes are dragging against the drum surface of the brake rotor and causing noise. ACTION Replace the rear parking brake shoes and retainer springs on both sides of the vehicle. - If the parking brake shoes have worn through their lining and scored either the left side or right side drum surface of the brake rotor, or if any other related damage is present, replace the brake rotor on the affected side and replace the disk brake pads.

NTB17-066

Service Bulletin/Repair Instructions

2016-2017 TITAN XD; MIL ON WITH DTC U3017 This bulletin applies only to vehicles equipped with a Cummins 5.0L V8 Diesel engine. IF YOU CONFIRM The MIL is ?ON? with DTC U3017 (CAN Communication), and There are no drivability issues. ACTION 1. Save Computer Data with CONSULT-III plus (C-III plus). 2. At step 6 of the reprogramming procedure, confirm this bulletin applies to the vehicle you are working on. 3. If this bulletin applies, continue with reprogramming. 4. Write Saved Data with C-III plus. 5. Perform DTC Confirmation Procedure and Clear DTC.

NTB16-051a

Service Bulletin/Repair Instructions

2016 TITAN XD; MIL ON WITH HESITATION ON ACCEL IN COLD TEMPERATURE This bulletin applies only to vehicles equipped with a Cummins 5.0L V8 Diesel engine. This bulletin has been amended. A DTC has been removed from the IF YOU CONFIRM section. No other changes have been made. Please discard previous versions of this bulletin.

NTB17-060

Service Bulletin/Repair Instructions

2016 TITAN XD; MIL ON WITH P207F STORED This bulletin applies only to vehicles equipped with a Cummins 5.0L V8 Diesel engine. IF YOU CONFIRM The MIL is ON with P207F (Reductant Quality Performance) stored. ACTION 1. Save Computer Data with CONSULT-III plus (C-III plus). 2. At step 6 of the reprogramming procedure, confirm this bulletin applies to the vehicle you are working on. 3. If this bulletin applies, continue with reprogramming procedure. 4. Write Saved Data with CONSULT-III plus. 5. Perform DTC confirmation.

NTB17-061

Service Bulletin/Repair Instructions

2016-2017 TITAN XD; DELAY WITH RE-ACCELERATION This bulletin applies only to vehicles equipped with a Cummins 5.0L V8 Diesel engine. IF YOU CONFIRM Re-acceleration delay as follows: - Driving at a moderate steady speed, then - Reduce accelerator position to slow down, then - Increase accelerator position to bring the vehicle back to the previous speed, then - There is a delay/hesitation before the vehicle begins to accelerate. ACTION 1. Save Computer Data with CONSULT-III plus (C-III plus). 2. At step 6 of the reprogramming procedure, confirm this bulletin applies to the vehicle you are working on. 3. If this bulletin applies, continue with reprogramming procedure. 4. Write Saved Data with CONSULT-III plus.

NTB17-062

Service Bulletin/Repair Instructions

2016-2017 TITAN XD; MIL ON WITH DTC P218F WHEN OPERATED IN AMBIENT TEMPERATURE AT 32°F OR BELOW This bulletin applies only to vehicles equipped with a Cummins 5.0L V8 Diesel engine. IF YOU CONFIRM The MIL is ON with DTC P218F (REDUCTANT NO FLOW DETECTED) stored When The vehicle is operated in ambient temperatures at 32°F (0°C) or below And There are no drivability issues. ACTION 1. Save Computer Data with CONSULT-III plus (C-III plus). 2. At step 6 of the reprogramming procedure (page 7), confirm this bulletin applies to the vehicle you are working on. 3. If this bulletin applies, continue with reprogramming. 4. Write Saved Data with C-III plus.

NTB17-063

Service Bulletin/Repair Instructions

2016-2017 TITAN XD; MIL ON WITH DTC P0604 AND/OR P2299 This bulletin applies only to vehicles equipped with a Cummins 5.0L V8 Diesel engine. IF YOU CONFIRM The MIL is ON with one or both of the following DTCs stored: - P0604 (ECM [Internal Control Module Random Access Memory (RAM) Error]) - P2299 (ACCEL PEDAL POS BRAKE SWITCH) And There are no drivability issues. ACTION 1. Save Computer Data with CONSULT-III plus (C-III plus). 2. At step 6 of the reprogramming procedure (page 7), confirm this bulletin applies to the vehicle you are working on. 3. If this bulletin applies, continue with reprogramming. 4. Write Saved Data with C-III plus.

NTB16-095a

Service Bulletin/Repair Instructions

2016 TITAN XD; MIL ON WITH DTC P226C OR P0471 WHEN OPERATED AT OR BELOW 32°F (0°C) This bulletin applies only to vehicles equipped with a Cummins 5.0L V8 Diesel engine. This bulletin has been amended. IF YOU CONFIRM section was updated. No other changes were made. Please discard all previous versions of this bulletin.

NTB17-008a

Service Bulletin/Repair Instructions

NISSAN; OIL LEAKING AROUND VALVE TIMING CONTROL SOLENOID VALVE This bulletin applies to vehicles equipped with 6-cylinder engines. For Titan and Titan XD, this bulletin applies only vehicles equipped with gasoline engines. This bulletin has been amended in the PARTS INFORMATION and CLAIMS INFORMATION sections. Discard previous versions of this bulletin.

NTB17-030

Service Bulletin/Repair Instructions

NISSAN; FUEL TANK IS SLOW OR DIFFICULT TO FILL IF YOU CONFIRM The fuel tank is slow or difficult to fill (filling nozzle shuts off before tank is full). IMPORTANT: Make sure this incident has been duplicated at a gas station by dealer service staff. ACTION Perform the Service Procedure in this bulletin, starting on the next page.

NTB16-100b

Service Bulletin/Repair Instructions

20172016-2017 NISSAN CONNECT NAVIGATION SYSTEM SOFTWARE UPDATE This bulletin applies only to vehicles equipped with navigation system. This bulletin has been amended. The APPLIED VEHICLES section has been revised. No other changes have been made. Please discard previous versions of this bulletin.

NTB17-031

Service Bulletin/Repair Instructions

2016 - 2017 TITAN XD; COOLANT HEATER (ENGINE BLOCK HEATER) INSTALLATION This bulletin applies only to vehicles equipped with Cummins 5.0L Diesel engine. SERVICE INFORMATION Some customers may want to use a coolant heater (engine block heater) for their vehicle when ambient temperatures are below 32°F (0°C). 2016 Titan XD: - Some were not equipped from the factory with a coolant heater or cord. - Some were equipped with coolant heater, but not a cord. 2017 Titan XD: Was equipped from the factory with a coolant heater, but some were not equipped with the coolant heater cord. If a customer chooses to purchase the parts and labor for installation of a coolant heater and/or coolant heater cord, use the Service Procedure in this bulletin for installation instructions.

NTB16-056a

Service Bulletin/Repair Instructions

2016-2017 TITAN XD; EXHAUST SMELL INSIDE VEHICLE WHEN HVAC IS ON FRESH AIR This bulletin has been amended to update Applied Vehicles, add step 11 to the Service Procedure and add a flowchart. No other changes have been made. Please discard previous versions of this bulletin.

NTB17-026

Service Bulletin/Repair Instructions

BALL JOINT AXIAL END PLAY PROCEDURE SERVICE INFORMATION When working on the front suspension, use the updated service information in this bulletin along with the Electronic Service Manual (ESM). The updated information in this bulletin is a correction and a supplement to the ESM.

PC470-PC549-PC55

Service Bulletin/Repair Instructions

Tailgate Lock Dealer Inventory *****Dealer Announcement***** Nissan is conducting a dealer inventory service action on 1,004 specific 2016 Titan vehicles identified in Service Comm to replace components associated with the tailgate lock assembly. Affected vehicles are not subject to stop sale and are either currently in dealer inventory or assigned and in transit to the dealer. Nissan requests dealers to remedy the affected vehicles prior to sale to ensure customer satisfaction. *****What Dealers Should Do***** PLEASE FOLLOW THE ATTACHED REPAIR INSTRUCTIONS: 1. Verify if vehicles currently in new dealer inventory are affected by this service action using Service Comm I.D. PC470, PC549, and PC550. - New vehicles in dealer inventory can also be identified using DCS (Sales-> Vehicle Inventory, and filter by Open Campaign). - Refer to NPSB 15-460 for additional information 2. Use the attached procedure to identify which components to replace:

REVISION 3 - PC4

Service Bulletin/Repair Instructions

2016 Titan High Pressure Turbo- Voluntary Emissions Service Campaign - Dealer Announcement The announcement from December 15th, 2016 has been revised to include: - High pressure turbo kits and additional service parts for diesel engine repair are no longer on restriction and may be ordered via normal process. Orders placed prior to restriction removal will be fulfilled. Please discard earlier versions of this bulletin.

NTB16-108a

Service Bulletin/Repair Instructions

2016 TITAN XD; ENGINE RPM FLUCTUATES WHILE DRIVING AT STEADY SPEED This bulletin has been amended. The CLAIMS INFORMATION section has been corrected. No other changes have been made. Please discard previous versions of this bulletin.

NTB17-010

Service Bulletin/Repair Instructions

2016 - 2017 TITAN AND TITAN XD; STEP RAIL END CAP CHROME TRIM AVAILABLE AS SEPARATE PART This bulletin applies only to Crew Cab models. SERVICE INFORMATION The end cap chrome trim (front and rear) on the step rails (running boards) is now available as a separate part (see Parts Information). If the end cap chrome trim needs to be replaced for any reason (fell off, damaged, etc.), replace only the end cap chrome trim. NOTE: - The end cap chrome trim can be replaced without removing the end cap or step pad. - DO NOT replace the entire step rail when only the end cap chrome trim is needed. - Refer to Installation Tips on the next page

NTB17-008

Service Bulletin/Repair Instructions

NISSAN; OIL LEAKING AROUND VALVE TIMING CONTROL SOLENOID VALVE This bulletin applies only to Maxima, Quest, Altima Coupe, Altima, Pathfinder and Murano vehicles equipped with V6 engine OR Titan/Titan XD equipped with VK56 engine IF YOU CONFIRM Engine oil is leaking from a valve timing control solenoid valve, And The valve timing control solenoid valve operates correctly and is not externally damaged. ACTION Replace the valve timing control solenoid valve O-ring with a new one using the Service Procedure starting on page 2.

NTB16-100a

Service Bulletin/Repair Instructions

20172016-2017 NISSAN CONNECT NAVIGATION SYSTEM SOFTWARE UPDATE This bulletin only applies to vehciles equipped with navigation system. This bulletin has been amended. The APPLIED VEHICLES section has been revised. No other changes have been made. Please discard previous versions of this bulletin.

NTB16-038b

Service Bulletin/Repair Instructions

2016-2017 TITAN XD; 6AT TRANSMISSION CALIBRATION This bulletin has been amended to direct technicians to the ESM for transmission adjustment. Please discard previous versions of this bulletin.

NTB17-001

Service Bulletin/Repair Instructions

2016-2017 TITAN XD; CORRECT PARKING ANGLE OF VEHICLE WHEN USING ENGINE BLOCK HEATER SERVICE INFORMATION When using the engine block heater (if equipped) on an Applied Vehicle (engine block heater is plugged in): - Vehicle should be parked on a level surfaces. Or - If a level surface is not available, the vehicle should be parked with the front of the truck lower than the rear (nose down). CAUTION: Use of the engine block heater when parked with the front of the vehicle higher than the rear (5 degrees or more) may cause the engine block heater to become damaged and/or inoperative.

NTB16-125

Service Bulletin/Repair Instructions

2016-2017 TITAN XD; DIESEL EXHAUST FLUID (DEF) AND DIESEL FUEL CONTAMINATION PRECAUTION SERVICE INFORMATION CAUTION: Contamination of the Diesel Exhaust Fluid (DEF) system with fluids other than DEF can cause permanent damage to the components of the DEF system. CAUTION: Putting DEF or gasoline into the diesel fuel system will contaminate the entire system and can cause permanent damage to the components of the diesel fuel system. IMPORTANT: Damage to either of these systems due to contamination is not covered by the Nissan New Vehicle Warranty and will be the responsibility of the vehicle owner. Vehicle owners must be extremely careful to put the appropriate fluid/fuel into the appropriate tank.

Revision 2 - PC4

Service Bulletin/Repair Instructions

High Pressure Turbocharger Voluntary Emissions Service Campaign The announcement from October 13th, 2016 has been revised to include: o Campaign Bulletin NTB16-097 has been amended to include instructions for repair if the High Pressure turbo fails inspection and DTC P0524 (Engine Oil Pressure) is stored. - Please discard earlier versions of this bulletin.

NTB16-097a

Service Bulletin/Repair Instructions

VOLUNTARY EMISSIONS SERVICE CAMPAIGN 2016 TITAN XD WITH CUMMINS 5.0L; HIGH PRESSURE TURBOCHARGER This bulletin has been amended to include instructions for repair if DTC P0524 is stored and, if the HP turbo fails inspection. Please discard previous versions of this bulletin.

NTB16-123

Service Bulletin/Repair Instructions

PLASTIC INTERIOR TRIM PROTECTIVE COVERING REMOVAL SERVICE INFORMATION Vehicles are delivered with plastic interior trim protective covering on the front and rear seats, front and rear door panel finishers, steering wheel, and sun visors (see examples on page 2). When removing the protective covering, care must be used to avoid scuffs, scrapes, cuts, and other abrasive contact to interior trim components. DO NOT use sharp objects like razor blades, box cutters, knives, etc. when removing the plastic interior trim protective covering. IMPORTANT All soft trim described in this bulletin is on automatic return to NNA. Any trim found damaged in the way described in this bulletin will be charged back to the dealer.

NTB13-107a

Service Bulletin/Repair Instructions

INTELLIGENT KEY NOT DETECTED / ENGINE WILL NOT START This bulletin has been amended to update the Applied Vehicles and make changes to the body of the bulletin. Please discard previous versions.

NTB16-116

Service Bulletin/Repair Instructions

NISSAN; DIAGNOSIS INFORMATION FOR ABS DTC C1130 SERVICE INFORMATION When diagnosing for DTC C1130 (ENGINE SIGNAL): ECM related DTCs (P-codes) must be diagnosed, repaired, and DTCs erased first. - DTC C1130 is an ABS DTC that indicates an output signal of the ECM is not recognized. - Absent or incorrect ECM signals, that are indicated by corresponding P-codes, may trigger C1130 in the ABS control unit. - Some vehicle features that can be affected by absent or incorrect ECM signals are: - Forward Emergency Braking (FEB) - Intelligent Cruise Control (ICC) - VDC/ABS/TCS

NTB15-049j

Service Bulletin/Repair Instructions

TELEMATICS SERVICE INFORMATION This bulletin has been amended. Information for 2017 Rogue and Rogue Hybrid has been applied. No other changes have been made. Please discard previous versions of this bulletin.

NTB16-108

Service Bulletin/Repair Instructions

2016 TITAN XD; ENGINE RPM FLUCTUATES WHILE DRIVING AT STEADY SPEED IF YOU CONFIRM While driving at a steady speed, the engine RPM goes up and down (fluctuates) a small amount. ACTION 1. Refer to step 6 in the SERVICE PROCEDURE to confirm TCM reprogramming applies. 2. If it applies, reprogram the TCM.

NTB16-045a

Service Bulletin/Repair Instructions

2016-2017 TITAN XD; 7 A/T DTCs STORED This bulletin has been amended to update Applied Vehicles. Please discard previous versions of this bulletin.

PC507

Service Bulletin/Repair Instructions

Transmission Control Module Reprogram ***** Detailed Information ***** Nissan is conducting a dealer inventory service action to reprogram and, if necessary calibrate, the Transmission Control Module (TCM) on specific MY2016-17 Titan XD (A61D) vehicles identified in SERVICE COMM. These vehicles are either currently in dealer inventory or assigned and in transit to the dealer. No parts are required for this action. ***** What Dealers Should Do ***** 1. Verify if vehicles currently in dealer inventory are affected by this inventory service action using Service Comm I.D. PC507. 2. Use the attached procedure to reprogram and, if necessary, calibrate the TCM. Note: Dealers should continue to check new arriving inventory for applicability. 3. Dealers are requested to remedy any affected vehicle in dealer new or pre-owned inventory to ensure customer satisfaction.

NTB16-038a

Service Bulletin/Repair Instructions

2016-2017 TITAN XD; 6AT TRANSMISSION CALIBRATION This bulletin has been amended. Steps 13, 16, 17, 19, 22 and 23 have been revised, the APPLIED VEHICLES section has been updated, and page 10 has been created for distribution to the customer. No other changes have been made. Please discard previous versions of this bulletin.

NTB16-068b

Service Bulletin/Repair Instructions

2016-2017 TITAN XD; TRANSMISSION SHIFT QUALITY ISSUES This bulletin has been amended. Changes have been made throughout. Please discard previous versions of this bulletin.

NTB16-102

Service Bulletin/Repair Instructions

2016 TITAN XD; BUZZ NOISE FROM SUBWOOFER IF YOU CONFIRM With the audio system ON, a buzz/vibration noise is coming from the subwoofer mounting points under the passenger side seat. NOTE: If this incident should occur, - The customer may report the noise is coming from the passenger door. - The noise may be heard inside and outside the vehicle. ACTION Install the new subwoofer mounting screws and grommets listed in the PARTS INFORMATION section.

NTB16-101

Service Bulletin/Repair Instructions

2016 TITAN XD WITH CUMMINS 5.0L; DPF WARNING LIGHT IS ON IF YOU CONFIRM: The Diesel Particulate Filter (DPF) warning light is ON AND/OR The Vehicle Information Display states "Exhaust Filter Overloaded See Owner's Manual For Drive Pattern" AND DTC P1451 (Diesel Particulate Filter System Performance) is stored in the ECM NOTE: This DTC will not turn the MIL ON. AND The vehicle has less than 100 miles on the odometer. ACTION: 1. Perform a stationary regeneration. - Go to SERVICE PROCEDURE on page 2. 2. Erase the DTC.

NTB16-037d

Service Bulletin/Repair Instructions

2016 TITAN XD; MIL ON WITH ENGINE DTCs STORED AND/OR IDLE FLUCTUATION This bulletin has been amended to revise the IF YOU CONFIRM section, add information to step 6B and Table A. No other changes were made. Please discard previous versions of this bulletin.

NTB16-099

Service Bulletin/Repair Instructions

2016-2017 TITAN AND TITAN XD; REVISED WHEEL ALIGNMENT SPECIFICATIONS SERVICE INFORMATION Some of the wheel alignment specifications listed in the Front Suspension (FSU) and Rear Suspension (RSU) sections of the 2016 and 2017 Titan Electronic Service Manual (ESM) have been revised. Updated ESMs will be distributed to the field as quickly as possible. Until the updated ESMs are made available, please use the revised service information hyperlinked below.

Revision 1 - PC4

Service Bulletin/Repair Instructions

High Pressure Turbocharger - Voluntary Emissions Service Campaign The announcement from September 1st, 2016 has been revised to include: o Campaign Bulletin NTB16-097 is now available on NNAnet, ASIST & Dealer360. o Service Comm now active for retailed VINs. o Dealers may order parts for affected retailed units via DCS beginning October 13, 2016. - Please discard earlier versions of this bulletin.

NTB16-089a

Service Bulletin/Repair Instructions

2016 ? 2017 TITAN XD; HEADLAMP AIMING This bulletin has been amended. LED headlamp adjustment information has been corrected. Please discard previous versions of this bulletin.

NTB16-097

Service Bulletin/Repair Instructions

VOLUNTARY EMISSIONS SERVICE CAMPAIGN 2016 TITAN XD WITH CUMMINS 5.0L; HIGH PRESSURE TURBOCHARGER INTRODUCTION Nissan is conducting a Voluntary Emissions Service Campaign on certain specific Model Year 2016 Nissan Titan XD vehicles with Cummins 5.0L to inspect and replace the high pressure turbocharger assembly. This service will be performed at no charge to owners for parts or labor. IDENTIFICATION NUMBER Nissan has assigned identification number PC471 to this campaign. The correct number must appear on all communications and documentation of any nature dealing with this campaign. DEALER RESPONSIBILITY Dealers are to correct each vehicle falling within the range of this campaign that enters the service department. This includes vehicles purchased from private parties or presented by transient (tourist) owners and vehicles in a dealer?s inventory.

NTB16-096

Service Bulletin/Repair Instructions

2016 TITAN XD; REFILLING AND AIR BLEEDING THE POWER STEERING SYSTEM SERVICE INFORMATION The Electronic Service Manual (ESM) pages for "Refilling and Air Bleeding Hydraulic System" in the ST-Steering System section have been updated/amended. Until the updated Service Manual is made available, please refer to the link below, as needed, for any service or repairs for the 2016 Titan XD that require Refilling and Air Bleeding the hydraulic power steering system.

NTB15-049i

Service Bulletin/Repair Instructions

TELEMATICS SERVICE INFORMATION ONLY SPECIFIC TRIM PACKAGES ARE AFFECTED This bulletin has been amended. Information for 2017 Altima, Murano, Pathfinder, Sentra, and Titan/Titan XD vehicles has been applied. No other changes have been made. Please discard previous versions of this bulletin.

NTB16-095

Service Bulletin/Repair Instructions

2016 TITAN XD; MIL ON WITH DTC P226C OR P0471 IF YOU CONFIRM One or both of the following DTCs are stored: - P226C (Turbocharger Boost Control Slow Response) - P0471 (Exhaust Pressure Sensor "A" Circuit Range/Performance) and There are no drivability issues. ACTION 1. Save Computer Data with CONSULT-III plus (C-III plus). 2. At step 6 of the reprogramming procedure, confirm this bulletin applies to the vehicle you are working on. 3. If this bulletin applies, continue with reprogramming. 4. Write Saved Data with C-III plus.

PC494 - 2016-17

Service Bulletin/Repair Instructions

FUEL TANK BREATHER TUBE DEALER INVENTORY ***** DETAILED INFORMATION ***** NISSAN IS CONDUCTING A DEALER INVENTORY SERVICE ACTION TO INSPECT THE ROUTING OF THE FUEL TANK BREATHER TUBE ON APPROXIMATELY 6,379SPECIFIC MY2016-17 TITAN XD (A61D) VEHICLES. DURING VEHICLE ASSEMBLY, THE FUEL TANK BREATHER TUBE MAY NOT HAVE PROPERLY ROUTED AND INSTALLED. NO PARTS ARE REQUIRED FOR THIS ACTION.

PC423OL

Service Bulletin/Repair Instructions

Nissan is conducting this voluntary service campaign on certain specific 2016 Titan XD vehicles to install a dual wall bedliner and a cargo tie down kit that should have been installed on the vehicle from the factory, but were not.

PC428OL

Service Bulletin/Repair Instructions

Nissan is conducting a voluntary service campaign on certain MY2016 Titan XD vehicles to install step rails on vehicles that should be equipped with this accessory, but were shipped without the step rails installed.

PC434OL

Service Bulletin/Repair Instructions

Nissan is conducting a voluntary service campaign on certain MY2016 Titan XD vehicles to install splash guards on vehicles that should be equipped with this accessory, but were shipped without the splash guards installed.

PC466OL

Service Bulletin/Repair Instructions

vehicles to install an electronic tailgate lock that should have been installed on the vehicle from the factory, but was not.

NTB16-068A

Service Bulletin/Repair Instructions

2016 TITAN XD; ENGINE RPM FLARE DURING UP SHIFT AND/OR DOWN SHIFT BUMP THIS BULLETIN HAS BEEN AMENDED. THE SERVICE PROCEDURE HAS BEEN REVISED, AND APPLIED VIN AND DATE INFORMATION HAS BEEN ADDED. NO OTHER CHANGES HAVE BEEN MADE. PLEASE DISCARD ALL PREVIOUS VERSIONS.

NTB16-089

Service Bulletin/Repair Instructions

2016 TITAN XD; HEADLAMP AIMING WHEN ADJUSTING THE HEADLAMPS ON A TITAN XD, MAKE SURE TO FOLLOW THE PROCEDURES IN THE ELECTRONIC SERVICE MANUAL (ESM). - WARRANTY CLAIMS FOR HEADLAMP ADJUSTMENT ARE SUBJECT TO AUDIT. - CLAIMS MUST HAVE THE MEASUREMENTS FOR DIMENSION A, B, AND C (SHOWN IN THIS BULLETIN) LISTED ON THE REPAIR ORDER AND ON THE TECHNICIAN COMMENTS LINE OF THE CLAIM. - CLAIMS SUBMITTED WITHOUT THESE MEASUREMENTS MAY BE DENIED.

NTB16-078A

Service Bulletin/Repair Instructions

VOLUNTARY SERVICE CAMPAIGN 2016 TITAN XD; DUAL WALL BEDLINER AND CARGO TIE DOWN KIT THIS BULLETIN HAS BEEN AMENDED. THE PARTS INFORMATION SECTION HAS BEEN REVISED. NO OTHER CHANGES HAVE BEEN MADE. PLEASE DISCARD PREVIOUS VERSIONS OF THIS BULLETIN.

REVISION 1-PC423

Service Bulletin/Repair Instructions

TITAN BOX VOLUNTARY SERVICE CAMPAIGN THE ANNOUNCEMENT FROM AUGUST 24TH, 2016 HAS BEEN REVISED TO INCLUDE: O THE PARTS INFORMATION SECTION HAS BEEN REVISED. NO OTHER CHANGES HAVE BEEN MADE. - PLEASE DISCARD EARLIER VERSIONS OF THIS BULLETIN.

NTB16-074A

Service Bulletin/Repair Instructions

2016 TITAN XD; TAILGATE WILL NOT OPEN OR UNLOCK THIS BULLETIN HAS BEEN AMENDED. THE APPLIED DATE INFORMATION IN THE REPAIR FLOW CHART ON PAGE 2 AND IN STEPS 6A AND 6B HAVE BEEN REVISED. NO OTHER CHANGES HAVE BEEN MADE. PLEASE DISCARD ALL PREVIOUS VERSIONS.

PC471 - 2016 TIT

Service Bulletin/Repair Instructions

HIGH PRESSURE TURBOCHARGER VOLUNTARY EMISSIONS SERVICE CAMPAIGN DIESEL ENGINE ONLY ***** CAMPAIGN SUMMARY ***** AS PER OUR AUGUST 5TH ANNOUNCEMENT, NISSAN IS CONDUCTING A VOLUNTARY EMISSIONS SERVICE CAMPAIGN ON APPROXIMATELY 683 SPECIFIC MY 2016 TITAN XD DIESEL (A61) VEHICLES CURRENTLY IN DEALER INVENTORY TO ADDRESS AN EXCESSIVE OIL CONSUMPTION CONCERN WITH THE HIGH PRESSURE TURBOCHARGER. NISSAN HAS AUTOMATICALLY SHIPPED PARTS TO REPAIR AFFECTED VEHICLES CURRENTLY IN DEALER NEW VEHICLE INVENTORY AND SUBJECT TO THE QUALITY HOLD. DEALERS SHOULD FOLLOW THE REPAIR INSTRUCTIONS INCLUDED WITH THIS ANNOUNCEMENT TO REPAIR AFFECTED VEHICLES IN NEW VEHICLE INVENTORY. NISSAN IS STILL DEVELOPING A REPAIR PROCEDURE FOR AFFECTED RETAILED VEHICLES AT THIS TIME. NISSAN HAS NOT YET IDENTIFIED THESE VEHICLES IN SERVICE COMM. NISSAN EXPECTS TO BE ABLE TO MAKE AN ANNOUNCEMENT REGARDING RETAILED VEHICLES BY MID-TO-LATE SEPTEMBER. NOTE: ONLY CERTAIN TITAN XD DIESEL VEHICLES ARE AFFECTED, WHILE OTHER TITAN XD DIESEL VEHICLES ARE NOT, SO DEALERS NEED TO FOLLOW INSTRUCTIONS BELOW TO IDENTIFY THE AFFECTED VEHICLES. ***** WHAT DEALERS SHOULD DO ***** 1. VERIFY IF VEHICLES ARE AFFECTED BY THIS VOLUNTARY EMISSIONS SERVICE CAMPAIGN USING SERVICE COMM I.D. PC471. 2. DEALERS ARE REQUESTED TO REPAIR ANY AFFECTED VEHICLES IN DEALER NEW OR PRE-OWNED INVENTORY TO ENSURE CUSTOMER SATISFACTION. 3. REPAIR THE VEHICLE USING THE ATTACHED REPAIR PROCEDURE. NOTE: IF DTC P0524 IS FOUND STORED, DEALERS WILL NEED TO SEND THE REQUESTED DETAILS TO NNAFQASUPPORT@NISSAN-USA.COM AND AWAIT FURTHER INSTRUCTION. 4. ONCE REPAIRED, DEALERS SHOULD SUBMIT THE CLAIM, USING THE CLAIMS CODING PROVIDED, AND RELEASE THE VEHICLE. 5. DEALERS ARE REMINDED TO FOLLOW ALL LOCAL LAWS AND REGULATIONS REGARDING DISCLOSURES OF REPAIRS TO NEW VEHICLES PRIOR TO SALE.

MAILY 2016 TITAN

Service Bulletin/Repair Instructions

WARRANTY INFORMATION BOOKLET VOLUNTARY EMISSION SERVICE CAMPAIGN GAS ENGINE ONLY NISSAN IS CONDUCTING A VOLUNTARY EMISSION SERVICE CAMPAIGN ON APPROXIMATELY 1,044 MODEL YEAR 2016 NISSAN TITAN XD (GASOLINE ONLY) VEHICLES. NISSAN HAS DISCOVERED THAT MODEL YEAR 2016 WARRANTY INFORMATION BOOKLET CONTAINS INACCURATE INFORMATION RELATED TO THE FEDERAL EMISSION PERFORMANCE AND DEFECT WARRANTY COVERAGE DETAILS. THE VEHICLES EMISSION PERFORMANCE AND DEFECT WARRANTIES WERE INCORRECTLY LISTED AND SHOULD HAVE BEEN LISTED AS 5 YEARS / 50,000 MILES. THE VEHICLES FEDERAL AND CALIFORNIA EMISSION LONG TERM DEFECT WARRANTIES REMAIN UNCHANGED. VEHICLE SAFETY, FUEL ECONOMY, DRIVABILITY AND PERFORMANCE ARE NOT AFFECTED. TO CORRECT THIS CONDITION, NISSAN IS CONDUCTING A VOLUNTARY EMISSION SERVICE CAMPAIGN TO PROVIDE A WARRANTY ADDENDUM STICKER THAT CONTAINS THE MOST CURRENT EMISSION WARRANTY INFORMATION TO OWNERS AND DEALERS WITH AFFECTED INVENTORY.

PC423 - 2016 TIT

Service Bulletin/Repair Instructions

TITAN BOX VOLUNTARY SERVICE CAMPAIGN ***** CAMPAIGN SUMMARY ***** NISSAN IS CONDUCTING A VOLUNTARY SERVICE CAMPAIGN ON CERTAIN MY2016 TITAN XD VEHICLES TO INSTALL STORAGE BOXES ON VEHICLES THAT SHOULD BE EQUIPPED WITH THIS ACCESSORY, BUT WERE SHIPPED WITHOUT THE STORAGE BOXES INSTALLED. ***** WHAT DEALERS SHOULD DO ***** 1. VERIFY IF VEHICLES ARE AFFECTED BY THIS VOLUNTARY SERVICE CAMPAIGN USING SERVICE COMM I.D. PC423. 2. DEALERS ARE REQUESTED TO REPAIR ANY AFFECTED VEHICLES IN DEALER NEW OR PRE-OWNED INVENTORY TO ENSURE CUSTOMER SATISFACTION. 3. REPAIR THE VEHICLE USING THE REPAIR PROCEDURE IN NTB16-078. 4. ONCE REPAIRED, DEALERS SHOULD SUBMIT THE CLAIM, USING THE CLAIMS CODING PROVIDED, AND RELEASE THE VEHICLE.

PC428 - 2016 TIT

Service Bulletin/Repair Instructions

STEP RAILS VOLUNTARY SERVICE CAMPAIGN ***** CAMPAIGN SUMMARY ***** NISSAN IS CONDUCTING A VOLUNTARY SERVICE CAMPAIGN ON CERTAIN MY2016 TITAN XD VEHICLES TO INSTALL STEP RAILS ON VEHICLES THAT SHOULD BE EQUIPPED WITH THIS ACCESSORY, BUT WERE SHIPPED WITHOUT THE STEP RAILS INSTALLED. ***** WHAT DEALERS SHOULD DO ***** 1. VERIFY IF VEHICLES ARE AFFECTED BY THIS VOLUNTARY SERVICE CAMPAIGN USING SERVICE COMM I.D. PC428. 2. DEALERS ARE REQUESTED TO REPAIR ANY AFFECTED VEHICLES IN DEALER NEW OR PRE-OWNED INVENTORY TO ENSURE CUSTOMER SATISFACTION. 3. REPAIR THE VEHICLE USING THE REPAIR PROCEDURE IN NTB16-081. 4. ONCE REPAIRED, DEALERS SHOULD SUBMIT THE CLAIM, USING THE CLAIMS CODING PROVIDED, AND RELEASE THE VEHICLE.

PC434 - 2016 TIT

Service Bulletin/Repair Instructions

SPLASH GUARDS VOLUNTARY SERVICE CAMPAIGN ***** CAMPAIGN SUMMARY***** NISSAN IS CONDUCTING A VOLUNTARY SERVICE CAMPAIGN ON CERTAIN MY2016 TITAN XD VEHICLES TO INSTALL SPLASH GUARDS ON VEHICLES THAT SHOULD BE EQUIPPED WITH THIS ACCESSORY, BUT WERE SHIPPED WITHOUT THE SPLASH GUARDS INSTALLED. ***** WHAT DEALERS SHOULD DO***** 1. VERIFY IF VEHICLES ARE AFFECTED BY THIS VOLUNTARY SERVICE CAMPAIGN USING SERVICE COMM I.D. PC434. 2. DEALERS ARE REQUESTED TO REPAIR ANY AFFECTED VEHICLES IN DEALER NEW OR PRE-OWNED INVENTORY TO ENSURE CUSTOMER SATISFACTION. 3. DEALERS SHOULD USE NTB16-080 TO CORRECT ANY VEHICLES SUBJECT TO THIS CAMPAIGN. 4. ONCE REPAIRED, DEALERS SHOULD SUBMIT A WARRANTY CLAIM AND RELEASE THE VEHICLE.

PC466 - 2016 TIT

Service Bulletin/Repair Instructions

ELECTRONIC TAILGATE LOCK VOLUNTARY SERVICE CAMPAIGN ***** CAMPAIGN SUMMARY ***** NISSAN IS CONDUCTING A VOLUNTARY SERVICE CAMPAIGN ON CERTAIN MY2016 TITAN XD VEHICLES TO INSTALL ELECTRONIC TAILGATE LOCKS ON VEHICLES THAT SHOULD BE EQUIPPED WITH THIS ACCESSORY, BUT WERE SHIPPED WITHOUT THE ELECTRONIC TAILGATE LOCKS INSTALLED. ***** WHAT DEALERS SHOULD DO ***** 1. VERIFY IF VEHICLES ARE AFFECTED BY THIS VOLUNTARY SERVICE CAMPAIGN USING SERVICE COMM I.D. PC466. 2. DEALERS ARE REQUESTED TO REPAIR ANY AFFECTED VEHICLES IN DEALER NEW OR PRE-OWNED INVENTORY TO ENSURE CUSTOMER SATISFACTION. 3. REPAIR THE VEHICLE USING THE REPAIR PROCEDURE IN NTB16-079. 4. ONCE REPAIRED, DEALERS SHOULD SUBMIT THE CLAIM, USING THE CLAIMS CODING PROVIDED, AND RELEASE THE VEHICLE.

NTB16-078

Service Bulletin/Repair Instructions

VOLUNTARY SERVICE CAMPAIGN 2016 TITAN XD; DUAL WALL BEDLINER AND CARGO TIE DOWN KIT INTRODUCTION NISSAN IS CONDUCTING THIS VOLUNTARY SERVICE CAMPAIGN ON CERTAIN SPECIFIC 2016 TITAN XD VEHICLES TO INSTALL A DUAL WALL BEDLINER AND A CARGO TIE DOWN KIT THAT SHOULD HAVE BEEN INSTALLED ON THE VEHICLE FROM THE FACTORY, BUT WERE NOT. THIS SERVICE WILL BE PERFORMED AT NO CHARGE TO THE CUSTOMER FOR PARTS OR LABOR. IDENTIFICATION NUMBER NISSAN HAS ASSIGNED IDENTIFICATION NUMBER PC423 TO THIS CAMPAIGN. THIS NUMBER MUST APPEAR ON ALL COMMUNICATIONS AND DOCUMENTATION OF ANY NATURE DEALING WITH THIS CAMPAIGN. DEALER RESPONSIBILITY DEALERS ARE TO REPAIR VEHICLES FALLING WITHIN RANGE OF THIS CAMPAIGN THAT ENTER THE SERVICE DEPARTMENT. THIS INCLUDES VEHICLES PURCHASED FROM PRIVATE PARTIES, VEHICLES PRESENTED BY TRANSIENT (TOURISTS) OWNERS, AND VEHICLES IN A DEALERS INVENTORY.

NTB16-079

Service Bulletin/Repair Instructions

VOLUNTARY SERVICE CAMPAIGN 2016 TITAN XD; ELECTRONIC TAILGATE LOCK INTRODUCTION NISSAN IS CONDUCTING THIS VOLUNTARY SERVICE CAMPAIGN ON CERTAIN SPECIFIC 2016 TITAN XD VEHICLES TO INSTALL AN ELECTRONIC TAILGATE LOCK THAT SHOULD HAVE BEEN INSTALLED ON THE VEHICLE FROM THE FACTORY, BUT WAS NOT. THIS SERVICE WILL BE PERFORMED AT NO CHARGE TO THE CUSTOMER FOR PARTS OR LABOR. IDENTIFICATION NUMBER NISSAN HAS ASSIGNED IDENTIFICATION NUMBER PC466 TO THIS CAMPAIGN. THIS NUMBER MUST APPEAR ON ALL COMMUNICATIONS AND DOCUMENTATION OF ANY NATURE DEALING WITH THIS CAMPAIGN. DEALER RESPONSIBILITY DEALERS ARE TO REPAIR VEHICLES FALLING WITHIN RANGE OF THIS CAMPAIGN THAT ENTER THE SERVICE DEPARTMENT. THIS INCLUDES VEHICLES PURCHASED FROM PRIVATE PARTIES, VEHICLES PRESENTED BY TRANSIENT (TOURISTS) OWNERS, AND VEHICLES IN A DEALERS INVENTORY.

NTB16-080

Service Bulletin/Repair Instructions

VOLUNTARY SERVICE CAMPAIGN 2016 TITAN XD; SPLASH GUARDS INTRODUCTION NISSAN IS CONDUCTING THIS VOLUNTARY SERVICE CAMPAIGN ON CERTAIN SPECIFIC 2016 TITAN XD VEHICLES TO INSTALL SPLASH GUARDS THAT SHOULD HAVE BEEN INSTALLED ON THE VEHICLE FROM THE FACTORY, BUT WERE NOT. THIS SERVICE WILL BE PERFORMED AT NO CHARGE TO THE CUSTOMER FOR PARTS OR LABOR. IDENTIFICATION NUMBER NISSAN HAS ASSIGNED IDENTIFICATION NUMBER PC434 TO THIS CAMPAIGN. THIS NUMBER MUST APPEAR ON ALL COMMUNICATIONS AND DOCUMENTATION OF ANY NATURE DEALING WITH THIS CAMPAIGN. DEALER RESPONSIBILITY DEALERS ARE TO REPAIR VEHICLES FALLING WITHIN RANGE OF THIS CAMPAIGN THAT ENTER THE SERVICE DEPARTMENT. THIS INCLUDES VEHICLES PURCHASED FROM PRIVATE PARTIES, VEHICLES PRESENTED BY TRANSIENT (TOURISTS) OWNERS, AND VEHICLES IN A DEALERS INVENTORY.

NTB16-081

Service Bulletin/Repair Instructions

VOLUNTARY SERVICE CAMPAIGN 2016 TITAN XD; RUNNING BOARDS INTRODUCTION NISSAN IS CONDUCTING THIS VOLUNTARY SERVICE CAMPAIGN ON CERTAIN SPECIFIC 2016 TITAN XD VEHICLES TO INSTALL RUNNING BOARDS THAT SHOULD HAVE BEEN INSTALLED ON THE VEHICLE FROM THE FACTORY, BUT WERE NOT. THIS SERVICE WILL BE PERFORMED AT NO CHARGE TO THE CUSTOMER FOR PARTS OR LABOR. IDENTIFICATION NUMBER NISSAN HAS ASSIGNED IDENTIFICATION NUMBER PC428 TO THIS CAMPAIGN. THIS NUMBER MUST APPEAR ON ALL COMMUNICATIONS AND DOCUMENTATION OF ANY NATURE DEALING WITH THIS CAMPAIGN. DEALER RESPONSIBILITY DEALERS ARE TO REPAIR VEHICLES FALLING WITHIN RANGE OF THIS CAMPAIGN THAT ENTER THE SERVICE DEPARTMENT. THIS INCLUDES VEHICLES PURCHASED FROM PRIVATE PARTIES, VEHICLES PRESENTED BY TRANSIENT (TOURISTS) OWNERS, AND VEHICLES IN A DEALERS INVENTORY.

UPDATE 2 - PC469

Service Bulletin/Repair Instructions

CENTER SEAT QUALITY ASSURANCE HOLD THE ANNOUNCEMENT FROM AUGUST 1ST, 2016 HAS BEEN REVISED TO INCLUDE: - REPAIR, PARTS, AND CLAIMS INFORMATION FOR THE PREVIOUSLY ANNOUNCED QUALITY HOLD

NTB16-082

Service Bulletin/Repair Instructions

2016 TITAN XD; BUMP FELT ON LIGHT THROTTLE APPLICATION AT SPEEDS OVER 40 MPH GAS V8 ENGINE ONLY WITH 7-SPEED A/T IF YOU CONFIRM A BUMP OR SHOCK IS FELT FROM THE DRIVETRAIN, - ONLY WHILE TRAVELING AT 40 MPH OR MORE, AND THEN - LIGHTLY APPLYING THE ACCELERATOR AFTER BRIEFLY COASTING. ACTION 1. REFER TO STEP 6 IN THE SERVICE PROCEDURE TO CONFIRM THIS BULLETIN APPLIES TO THE VEHICLE YOU ARE WORKING ON. 2. IF THIS BULLETIN APPLIES, REPROGRAM THE ECM.

UPDATE 1 - PC471

Service Bulletin/Repair Instructions

TITAN XD QUALITY ASSURANCE HOLD THE ANNOUNCEMENT FROM JULY 22ND, 2016 HAS BEEN REVISED TO INCLUDE: - INFORMATION ON ACTION NECESSARY FOR THE PREVIOUSLY ANNOUNCED QUALITY HOLD

NTB13-097D

Service Bulletin/Repair Instructions

ALL MODEL YEAR 2012 AND NEWER NISSAN VEHICLES; EVAP LEAK DTC P0442, P0455, P0456 INFORMATION THIS BULLETIN HAS BEEN AMENDED. THE TITLE HAS BEEN REVISED, AND THE BULLETIN NOW INCLUDES VEHICLES IN PRODUCTION AS OF THE DATE OF THIS UPDATE. NO OTHER CHANGES HAVE BEEN MADE. PLEASE DISCARD ALL PREVIOUS VERSIONS OF THIS BULLETIN.

NTB16-074

Service Bulletin/Repair Instructions

2016 TITAN XD; TAILGATE WILL NOT OPEN OR UNLOCK IF YOU CONFIRM - TAILGATE WILL NOT UNLOCK WITH THE MECHANICAL KEY OR ELECTRICALLY WITH THE KEY FOB. AND/OR - TAILGATE WILL NOT UNLATCH OR REQUIRES EXCESSIVE FORCE WHEN PULLING ON THE TAIL GATE HANDLE. ACTION SEE THE FLOW CHART ON PAGE 2 FOR THE APPROPRIATE REPAIR FOR THE VIN AND DATE OF THE VEHICLE BEING WORKED ON.

UPDATE 1 - PC469

Service Bulletin/Repair Instructions

CENTER SEAT QUALITY ASSURANCE HOLD THE ANNOUNCEMENT FROM JULY 14TH, 2016 HAS BEEN REVISED TO INCLUDE: - INFORMATION ON ACTION NECESSARY FOR THE PREVIOUSLY ANNOUNCED QUALITY HOLD ***** DETAILED INFORMATION ***** AS PER OUR PREVIOUS ANNOUNCEMENT, NISSAN PLACED A TEMPORARY QUALITY ASSURANCE (QA) HOLD ON APPROXIMATELY 23 MY 2016 TITAN VEHICLES ON JULY 14, 2016 TO ENSURE VEHICLES DELIVERED TO OUR CUSTOMERS MEET OUR EXACTING STANDARDS AND CUSTOMER EXPECTATIONS. THIS TEMPORARY HOLD REMAINS IN EFFECT. NISSAN HAS CONCLUDED THE AFFECTED VEHICLES WILL REQUIRE THE FRONT CENTER SEAT ASSEMBLY TO BE REPLACED AS THE CENTER SEAT RISER DOES NOT MEET NISSAN DESIGN STANDARDS. ***** WHAT DEALERS SHOULD DO ***** 1. VERIFY IF VEHICLES CURRENTLY IN DEALER INVENTORY ARE AFFECTED BY THIS QA HOLD USING SERVICE COMM I.D. PC469 NOTE: DEALERS SHOULD CONTINUE TO CHECK NEW ARRIVING INVENTORY FOR QA HOLD APPLICABILITY. 2. PLEASE DO NOT SELL OR TRADE ANY AFFECTED VEHICLES IN DEALER INVENTORY. 3. NO FURTHER ACTION IS NECESSARY AT THIS TIME. NISSAN WILL COMMUNICATE INSTRUCTIONS AND CLAIMS INFORMATION WHEN PARTS SHIPMENTS BEGIN TO AFFECTED DEALERS.

PC474 2016 TITAN

Service Bulletin/Repair Instructions

FRONT PROP SHAFT BOLT TORQUE DEALER INVENTORY INSPECTION *****DEALER ANNOUNCEMENT***** NISSAN IS CONDUCTING A DEALER INVENTORY INSPECTION ON 963 SPECIFIC 2016 TITAN VEHICLES IDENTIFIED IN SERVICE COMM. DEALERS SHOULD INSPECT THE FRONT PROP SHAFT BOLT TORQUE AND IF THE BOLTS ARE FOUND TO BE NOT TORQUED TO SPECIFICATION, ALL BOLTS AND NUTS SHOULD BE REPLACED AND TIGHTENED TO SPECIFICATION THESE VEHICLES ARE EITHER CURRENTLY IN DEALER INVENTORY OR ASSIGNED AND IN TRANSIT TO THE DEALER. *****WHAT DEALERS SHOULD DO***** PLEASE FOLLOW THE ATTACHED REPAIR INSTRUCTIONS: 1. VERIFY IF VEHICLES CURRENTLY IN DEALER INVENTORY ARE AFFECTED BY THIS INSPECTION USING SERVICE COMM I.D. PC474. -AS A REMINDER NEW VEHICLES IN DEALER INVENTORY CAN BE ALSO BE IDENTIFIED USING DCS (SALES-> VEHICLE INVENTORY, AND FILTER BY OPEN CAMPAIGN) OR SERVICE COMM. 2. USE THE ATTACHED PROCEDURE TO INSPECT THE FRONT PROP SHAFT BOLT TORQUE AND IF NECESSARY, REPLACE THE PROP SHAFT NUTS AND BOLTS AND TIGHTEN THE FASTENERS TO SPECIFICATION. 3. THE SERVICE DEPARTMENT SHOULD SUBMIT THE APPLICABLE WARRANTY CLAIM FOR THE ACTION PERFORMED SO IT CAN BE CLOSED ON SERVICE COMM AND RELEASE THE VEHICLE. ***** DEALER RESPONSIBILITY ***** IT IS THE DEALERS RESPONSIBILITY TO CHECK SERVICE COMM USING THE APPROPRIATE CAMPAIGN I.D FOR THE INSPECTION STATUS ON EACH AFFECTED VEHICLE CURRENTLY IN INVENTORY. NISSAN REQUESTS DEALERS TO PERFORM THIS INSPECTION ON VEHICLES IN INVENTORY PRIOR TO BEING RETAILED TO ENSURE CUSTOMER SATISFACTION.

NTB14-012D

Service Bulletin/Repair Instructions

REMOTE ENGINE START NOT WORKING THIS BULLETIN HAS BEEN AMENDED. CHANGES HAVE BEEN MADE TO ITEMS 1, 4, AND 13 IN THE SUPPLEMENTAL DIAGNOSIS TABLE. NO OTHER CHANGES HAVE BEEN MADE. PLEASE DISCARD PREVIOUS VERSIONS OF THIS BULLETIN. SERVICE INFORMATION IF A CUSTOMER STATES THE REMOTE ENGINE START (RES) FEATURE OF AN APPLIED VEHICLE IS NOT WORKING, MAKE SURE THE SYSTEM IS PROPERLY SET TO OPERATE: -THE IGNITION IS TURNED OFF -THE SHIFT SELECTOR IS IN PARK (P) -THE HOOD/DOORS/TRUNK LID/LIFT GATE ARE COMPLETELY CLOSED -NO OTHER OF THE VEHICLES INTELLIGENT KEYS (I-KEYS) ARE INSIDE, OR WITHIN STARTING RANGE OF, THE VEHICLE -THE I-KEY/KEY FOB (KEY FOB) IS WITHIN THE OPERATING RANGE OF 197 FT OR 60 M IF THE ABOVE CONDITIONS ARE MET, RES SHOULD WORK. 1. POINT THE KEY FOB AT THE VEHICLE. 2. PRESS THE LOCK BUTTON. 3. PRESS AND HOLD THE RES BUTTON WITHIN FIVE (5) SECONDS OF PRESSING THE LOCK BUTTON, UNTIL THE TURN SIGNAL LIGHTS TURN ON. WHENEVER AN APPLIED VEHICLE HAS A CONCERN WITH THE REMOTE ENGINE START (RES) FEATURE NOT WORKING PROPERLY, MAKE SURE TO VERIFY THE INCIDENT BEFORE STARTING ANY DIAGNOSIS AND/OR REPLACING PARTS. FOR A BETTER UNDERSTANDING OF THE RES SYSTEM, REFER TO SECTION 3: PRE-DRIVING CHECKS AND ADJUSTMENTS > REMOTE ENGINE START OF THE APPLIED VEHICLES OWNERS MANUAL. WHEN DIAGNOSING RES OPERATION, USE THE SUPPLEMENTAL RES SERVICE INFORMATION AND SUPPLEMENTAL DIAGNOSIS TABLE (STARTING ON PAGE 2) IN ADDITION TO THE ESM.

NTB09-118D

Service Bulletin/Repair Instructions

INTELLIGENT KEY BATTERY VOLTAGE CHECK AND REPLACEMENT THIS BULLETIN HAS BEEN SUPERSEDED BY NTB15-077. NISSAN; SIGNAL TECH-II INTELLIGENT KEY BATTERY TEST AND SIGNAL CHECK PLEASE DISCARD PREVIOUS VERSIONS OF THIS BULLETIN.

NTB16-068

Service Bulletin/Repair Instructions

2016 TITAN XD; ENGINE RPM FLARE DURING UP SHIFT AND/OR DOWN SHIFT BUMP IF YOU CONFIRM -WHEN COLD (TRANSMISSION FLUID BELOW 140°F [60°C]), THERE IS AN ENGINE RPM RISE (200 TO 500 RPM FLARE) DURING THE 1-2 SHIFT, 2-3 SHIFT, AND/OR THE 3-4 SHIFT. AND/OR -WHILE SLOWING TO A STOP, A 2-1 DOWN SHIFT BUMP IS FELT JUST BEFORE STOPPING. ACTION 1. COMPARE THE VEHICLES CURRENT TCM PART NUMBER TO THE PART NUMBER LISTED IN TABLE A ON PAGE 4. 2. IF THE CURRENT TCM PART NUMBER MATCHES A PART NUMBER LISTED IN TABLE A: A. REPROGRAM THE TCM. B. PERFORM TRANSMISSION CALIBRATION.

PC469 - 2016 TIT

Service Bulletin/Repair Instructions

CENTER SEAT QUALITY ASSURANCE HOLD A STOP SALE CONDITION IS IN EFFECT. ***** DETAILED INFORMATION ***** NISSAN IS COMMITTED TO A HIGH LEVEL OF CUSTOMER SERVICE AND SATISFACTION. THIS COMMITMENT REQUIRES NISSAN TO PERIODICALLY PLACE CERTAIN SPECIFIC VEHICLES ON A TEMPORARY QUALITY ASSURANCE (QA) HOLD TO ASSURE THAT THESE VEHICLES, AS DELIVERED TO OUR CUSTOMERS, MEET OUR EXACTING STANDARDS AND OUR CUSTOMERS EXPECTATIONS. EFFECTIVE IMMEDIATELY, NISSAN IS PLACING A TEMPORARY QUALITY ASSURANCE (QA) HOLD ON APPROXIMATELY 23 MY 2016 TITAN (A61 AND A61D) VEHICLES. ***** WHAT DEALERS SHOULD DO ***** 1. VERIFY IF VEHICLES CURRENTLY IN DEALER INVENTORY ARE AFFECTED BY THIS QA HOLD USING SERVICE COMM I.D. PC469 NOTE: DEALERS SHOULD CONTINUE TO CHECK NEW ARRIVING INVENTORY FOR QA HOLD APPLICABILITY. 2. PLEASE DO NOT DRIVE, SELL, OR TRADE ANY OF THE 2016 TITAN VEHICLES IN DEALER INVENTORY SUBJECT TO THIS QA HOLD. 3. NO FURTHER ACTION IS NECESSARY AT THIS TIME. NISSAN WILL PROVIDE AN UPDATE BY JULY 29TH, 2016.

NTB15-077A

Service Bulletin/Repair Instructions

NISSAN; SIGNAL TECH-II INTELLIGENT KEY BATTERY TEST AND SIGNAL CHECK THIS BULLETIN HAS BEEN AMENDED. CHANGES HAVE BEEN MADE THROUGHOUT. PLEASE DISCARD PREVIOUS VERSIONS OF THIS BULLETIN. IF YOU CONFIRM THE INTELLIGENT KEY INTERMITTENTLY OR CONTINUOUSLY DOES NOT FUNCTION. ACTION CHECK THE BATTERY CONDITION WITH THE SIGNAL TECH-II I-KEY BATTERY TEST. IMPORTANT: CONFIRM THAT THE SIGNAL TECH-II HAS THE MOST RECENT UPDATE. UPDATE CAN BE PERFORMED THROUGH ASIST / SPECIALTY TOOLS / SIGNAL TECH-II.

NTB16056

Service Bulletin/Repair Instructions

2016 TITAN XD; EXHAUST SMELL INSIDE VEHICLE WHEN HVAC IS ON FRESH AIR

NTB11027B

Service Bulletin/Repair Instructions

SERVICE INFORMATION Temporary tire Flat Spotting is common on New Dealer In-Stock vehicles that have not been occasionally moved. Flat Spotting can occur after the vehicle has been parked (not moved) for a few days, or longer. In most cases it is temporary. In extreme cases it can be permanent. Vehicles should be moved every 30 days, in one direction only, enough to rotate the tires 90° (see Figure 1). Moving vehicles as shown will prevent tire Flat Spotting. See this bulletin for further detail.

PC465

Service Bulletin/Repair Instructions

NISSAN IS CONDUCTING A DEALER INVENTORY SERVICE ACTION TO UPDATE THE ENGINE CONTROL MODULE (ECM) SOFTWARE ON 5,412 SPECIFIC 2016 TITAN XD VEHICLES IDENTIFIED IN SERVICE COMM. ON THE AFFECTED VEHICLES, THE SOFTWARE IS BEING UPDATED TO REFINE THE MIL ILLUMINATION LOGIC. THESE VEHICLES ARE EITHER CURRENTLY IN DEALER INVENTORY OR ASSIGNED AND IN TRANSIT TO THE DEALER.

NTB16036A

Service Bulletin/Repair Instructions

SERVICE INFORMATION This bulletin provides recommendations for proper engine operation in conditions where the ambient temperature is around or below 0°C (32°F). NOTE - These recommendations are also found in the vehicle Owner?s Manual. - Always use the correct engine oil for the prevailing conditions. - Use an engine block heater (if so equipped) when the ambient temperature is at or below -18°C (0°F). - Engine block heaters are used to assist with cold temperature starting. - Some engine block heaters will operate continuously while plugged into the correct voltage electrical outlet. IMPORTANT: DO NOT use the engine block heater in temperature conditions at or above 0°C (32°F). Doing so may cause damage to the engine block heater. See this bulletin for further detail.

NTB16037C

Service Bulletin/Repair Instructions

IF YOU CONFIRM The MIL is ON with one or more of the following DTCs stored: * P020A - F: Cylinder 1 - 6 Injection Timing * P021A - B: Cylinder 7 - 8 Injection Timing * P060C: Internal Control Module Main Processor Performance * P061B: Internal Control Module Torque Calculation Performance * P0605: ECM * P2048: Reductant Injector Circuit Low * P0299: Boost Pressure * P2263: Turbocharger Boost System Performance * P0401: Flow in the Exhaust Gas Recirculation (Insufficient) * P0402: Flow in the Exhaust Gas Recirculation (Excessive) * P2483: Exhaust Gas Temperature Sensor Circuit Intermittent 1/5 * P244D: Exhaust Temperature Too High For PF Regeneration * U0415: VDC CAN CIR2 * P2BAD: NOx Concentration Exceeded * P1C55: NOx Sensor 1/1 Intermittent * P1C56: NOx Sensor 1/2 Intermittent * P2201: NOx Sensor 1 and/or At times, when coming to a stop, the idle fluctuates with RPM dropping below 500 RPM. ACTION 1. Save Computer Data with CONSULT-III plus (C-III plus). 2. At step 6 of the reprogramming procedure, confirm this bulletin applies to the vehicle you are working on. 3. If this bulletin applies, continue with reprogramming procedure. 4. Write Saved Data with CONSULT-III plus. See this bulletin for further detail.

NTB15049H

Service Bulletin/Repair Instructions

SERVICE INFORMATION The Applied Vehicles are equipped with a wireless communication device called a Telematics Communication Unit (TCU). With an active NissanConnectSM Services subscription, the TCU communicates with the NissanConnectSM Services Data Center to provide various security and convenience services. This bulletin contains important service procedures that must be performed properly in order to set-up and maintain the telematics system for the Applied Vehicles. See this bulletin for further detail.

NTB16051

Service Bulletin/Repair Instructions

IF YOU CONFIRM The vehicle is operated as follows: * After being parked indoors overnight and started for the first time (cold start), * and then before reaching operating temperature is driven outside in an ambient temperature below 0°F (-18°C). Then * A hesitation is present while accelerating that improves as engine temperature increases, and subsides when the engine reaches normal operating temperature. And/or * The vehicle is operated in ambient temperatures at orbelow32°F (0°C) and one of these codes are stored. * P202E - Reductant Injection Valve Circuit 1/1 * P218F - Reductant No Flow Detected * P22CE - TC Outlet Switching Valve Stuck Closed Please see this bulletin for further details.

NTB16048

Service Bulletin/Repair Instructions

IF YOU CONFIRM The MIL is ON with one or more of the following DTCs stored as current: P22A7, P229E, P221A. ACTION 1. Replace the Outlet NOx Sensor. 2. Confirm that ECM requires reprogramming. Refer to step 6 on page 7. If the ECM requires reprograming: a. Perform Save Computer Data with CONSULT-III plus (C-III plus). b. Reprogram ECM. c. Perform Write Saved Data. See this bulletin for further detail.

NTB13106E

Service Bulletin/Repair Instructions

SERVICE INFORMATION If the configuration of the Audio/Navigation unit has not been completed correctly, some of the symptoms that may occur are: * Intermittent or no back up camera operation * No steering wheel switch response to audio inputs * No volume response from volume knob * Volume very loud or very quiet and adjustment is overly sensitive * Equalizer is adjusted so that Bass control is at maximum all the time * DTC U1000 for AVM C/U could be present If the above symptoms occur: * Confirm the configuration of the Audio/Navigation unit is correct. NOTE: Correct configuration of the appropriate control unit will restore correct operation. Audio/Navigation unit configuration is outlined starting on page 2. See this bulletin for further detail.

NTB13-099E

Service Bulletin/Repair Instructions

Audio Ulnit Replacement - Vehicles with color display audio and navigation system

NTB13099E

Service Bulletin/Repair Instructions

SERVICE INFORMATION If the Audio Unit needs to be replaced in an Applied Vehicle for any reason: - Write down replacement Audio Unit's registration "code" . - Replace the Audio Unit as instructed in the Electronic Service Manual (ESM) and any applicable bulletins. - Register the replacement Audio Unit with Nissan Owner Services. NOTE: The Apps mode will not function if the Audio Unit serial number (registration code) is not registered. See this bulletin for further detail.

NTB16-045

Service Bulletin/Repair Instructions

2016 Titan XD; 7 A/T DTCs Stored

NTB16045

Service Bulletin/Repair Instructions

SERVICE INFORMATION IMPORTANT: If you confirm one or more of the following transmission DTCs are stored: P0729: 6GR Incorrect Ratio P0730: Incorrect Gear Ratio P0731: 1GR Incorrect Ratio P0732: 2GR Incorrect Ratio P0733: 3GR Incorrect Ratio P0734: 4GR Incorrect Ratio P0735: 5GR Incorrect Ratio P1734: 7GR Incorrect Ratio Before performing any transmission repairs: 1. Check all of the engine intake air ducting and make sure: - It is connected securely and correctly at the throttle body and all other connections. See Figures 1 and 2 on the page 2. - All clamps and connectors are secure and tight. - There are no leaks. 2. Perform DTC confirmation procedure to confirm the incident. - Refer to the Electronic Service Manual (ESM) for DTC confirmation procedures. See this bulletin for further detail.

NTB09099A

Service Bulletin/Repair Instructions

IF YOU CONFIRM A refrigerant leak at a refrigerant pipe/hose joint location. ACTIONS 1. Inspect the metal surfaces of the pipe/hose joint for damage or contamination. NOTE: Do not replace a refrigerant pipe, hose, or other A/C component if an o-ring seal will solve the leak incident, if it should occur. 2. If no damage is found to the joint metal surfaces, replace the O-ring seal. See this bulletin for further detail.

NTB16-037

Service Bulletin/Repair Instructions

2016 Titan XD; MIL on with engine DTC s stored

PC438

Service Bulletin/Repair Instructions

Nissan is conducting a dealer inventory service action to inspect and, if necessary, replace the rear combination lamp assembly on 2,602 specific 2016 Titan XD vehicles.

PC455

Service Bulletin/Repair Instructions

Nissan is conducting a dealer inventory service action to torque the Engine Harness Ground to specification on 1,268 specific 2016 Titan XD vehicles.

NTB09131B

Service Bulletin/Repair Instructions

SERVICE INFORMATION Because of collision damage or other vehicle repair, a replacement "Certification Label" or "VIN Plate / Label" may be needed. These items may be available from Nissan by request if certain criteria are met. This bulletin lists the criteria and provides an application form for such replacements. See this bulletin for further detail.

NTB16-038

Service Bulletin/Repair Instructions

2016 Tit an XD (A61)

NTB16038AQAQAZQ

Service Bulletin/Repair Instructions

SERVICE INFORMATION Anytime the 6AT (RE6R01A) transmission or its Transmission Control Module (TCM) is replaced an adjustment procedure must be performed using C-III plus. IMPORTANT: If the transmission adjustment is not performed, the transmission may have the following conditions: Poor shift quality, Improper shift timing, Engine RPM flares between shifts See this bulletin for further detail.

NTB16-037A

Service Bulletin/Repair Instructions

IF YOU CONFIRM The MIL is ON with one or more of the following DTCs stored. P020A - F: Cylinder 1 6 Injection Timing P021A - B: Cylinder 7 8 Injection Timing P060C: Internal Control Module Main Processor Performance P2048: Reductant Injector Circuit Low P207F: Reductant Quality Performance P2263: Turbocharger Boost System Performance ACTION 1. Save Computer Data with CONSULT-III plus (C-III plus). 2. At step 6 of the reprogramming procedure, confirm this bulletin applies to the vehicle you are working on. 3. If this bulletin applies, continue with reprogramming procedure. 4. Write Saved Data with CONSULT-III plus.

NTB16-037a

Service Bulletin/Repair Instructions

2016 Titan XD; MIL on with engine DTC s stored

NTB16-036

Service Bulletin/Repair Instructions

2016 Titan XD; Cold weather starting tips

NTB15-044B

Service Bulletin/Repair Instructions

Fuel Filler Cap tether clip service information

NTB15044B

Service Bulletin/Repair Instructions

SERVICE INFORMATION If the clip for the fuel filler cap tether becomes lost or is detached for any reason, it is no longer necessary to replace the fuel filler cap. The clip or "pin" is now available as a separate service part. NOTE - Do not replace the fuel filler cap if only the pin is needed. See this bulletin for further detail.

NTB15-049G

Service Bulletin/Repair Instructions

SUMMARY TO BE PROVIDED ON A FUTURE DATE.

PC441

Service Bulletin/Repair Instructions

Nissan Bulletin - Engin Control Module (ECM) Reprogramming Dealer Inventory Service Action - Nissan is conducting a dealer inventory service action to update the Engine Control Module (ECM) software oin 3,334 specific 2016 Titan XD vehicles identified tin Service Comm. On the affected fvehicles, the software is being updated to refine the MIL illumination logic. These vehicles are either currently in dealer inventory or assigned and in transit to the dealer.

PC423B

Service Bulletin/Repair Instructions

Nissan has previously communicated instructions to dealers regarding specific vehicles in their inventory that may have been delivered without certain accessories. Nissan is delivering parts to those affected dealers to install the missing accessories on the vehicle.

PC423_PC428_PC43

Service Bulletin/Repair Instructions

Nissan Bulletin Titan Dealer Invefntory Service Actions Missing Accessory Clarification - Nissan has previously communicated instructions to dealers regarding specific vehicles in their inventory that may have been delivered without certain accessories. Nissan is delivering parts to those affected dealers to install the missing accessories on the vehicle. Nissan has instructed dealers to not trade the vehicles because the parts are being delivered to the original wholesale dealer of record. Nissan also requested dealers to install the parts shipped to them for affected vehicles before they are sold to ensure the vehicle has all the equipment listed on the Moinroney label and to ensure customer satisfaction. If the dealer elects to deliver an affected vehicle without this equipment installed, the dealer should inform the customer of the missing accessfory part(S) prior to sale. The dealer should also have the customer acknowledge in writing his/her understanding that the sfpecific accessory is included in the price of the vehiclew, but is not currently installed on the vefhicle, and the dealer will contact the customer to schedule an appointment for part installation upon the dealer's receipt of the part.

PC428A

Service Bulletin/Repair Instructions

PC434A

Service Bulletin/Repair Instructions

PC423

Service Bulletin/Repair Instructions

Nissan Bulletin Storage Box Dealer Inventory Service Action - Nissan has identified a small number of vehicles in dealer inventory that should be equipped with storage boxes, but were shipped without the storage boxes installed. 247 specific MY 2016 Titan XD vehicles idenfified in Service Comm will require storage box installation. These vehicles are currently in dealer inventory, assigned and in transit to the dealer, or retailed.

NTB03074J

Service Bulletin/Repair Instructions

SERVICE INFORMATION Occasionally customers may notice water vapor or fog in the headlamps. The information, illustrations, and flow chart in this bulletin are provided to help you in determining if an incident for water/condensation in the headlamps is normal or not. Nissan?s new vehicle limited warranty does not cover physically damaged (cracked or broken) headlamps. All current headlamp assemblies are vented to the atmosphere (not sealed). - This is necessary to allow for expansion and contraction of air from temperature "variations" (warmer or colder) without damage to the headlamp. - Moisture in the air sometimes "travels" into and out of the headlamp assembly through these vents. - Certain environmental conditions may cause moisture to condense. - The fogging/cloudiness should disappear over time when the headlamp is in a dry environment. See this bulletin for further detail.

NTB16014

Service Bulletin/Repair Instructions

SERVICE INFORMATION When diagnosing the front sonar parking sensor for unwanted activation (e.g. sonar activates with no obstacle ahead), inspect the front license plate, front license plate frame and if equipped, the front license plate bracket. See page 2 for example photos. The front sonar parking sensor may activate if the front license plate is bent outward from its bracket (there is a gap between the license plate and the bracket) OR the front license plate frame is bent or loose and is hanging outward, away from the license plate and/or bracket (there is a gap between the license plate frame and the license plate and/or bracket) OR the bracket is loose and is hanging outward, away from the bumper (there is a gap between the bracket and the bumper). If any of these conditions are found, correct it by removing the gap (straighten the license plate, straighten and/or secure the license plate frame, or secure the bracket, as it applies). - Retest the operation of the front sonar parking sensor. If the issue is not resolved, go to ASIST and the related Electronic Service Manual (ESM) for further diagnosis. See this bulletin for further detail.

NTB09081C

Service Bulletin/Repair Instructions

SERVICE INFORMATION The purpose of this bulletin is to give Nissan dealers guidelines to help determine if windshield breakage is covered under warranty or is the customer?s responsibility. Nissan North America (NNA) is not responsible for damage to glass that is a result of objects striking or scratching the glass. However, NNA is responsible for manufacturing issues such as distorted glass and cracks that are due to improper installation or damage to the glass during vehicle assembly. NNA typically does not find any type of cracks in the windshield due to stress after the dealership PDI. See this bulletin for further detail.

NTB15-116

Service Bulletin/Repair Instructions

2016 Titan XD Diesel; Battery disconnect wait time/DTCS P2509 & P181B Cummins 5.0 L Turbo Diesel.

NTB15116

Service Bulletin/Repair Instructions

SERVICE INFORMATION When disconnecting either of the 12 volt batteries on the Titan XD Diesel, follow these steps: 1. Turn the ignition OFF. 2. Wait at least 2 minutes. 3. Disconnect battery (negative cable first). NOTE: - If the above steps are not followed, DTCs P2509 and P181B may be stored. - If these codes are stored because the battery disconnection was done without waiting 2 minutes, they can be cleared, but it is not a warrantable repair. See this bulletin for more detail.

NTB16003

Service Bulletin/Repair Instructions

SERVICE INFORMATION The Intelligent Keys used on the various Nissan vehicles may not be interchangeable between models and years. See this bulletin for further detail.

NTB15043

Service Bulletin/Repair Instructions

SERVICE INFORMATION The appearance of painted alloy wheels can be damaged if acidic cleaners are used. DO NOT use Chrome Wheel Cleaner on Painted Wheels. Many chrome wheel cleaners have acidic ingredients. Make sure to follow all instruction in the Appearance and Care Section of the Owner?s Manual. Damage to wheel appearance due to the use of inappropriate chemicals or cleaning products is not covered under warranty. See this bulletin for further detail.

NTB14032

Service Bulletin/Repair Instructions

SERVICE INFORMATION Warranty claims coding for repairing wiring harnesses for all Nissan vehicles has changed. This bulletin gives an outline of the technician?s responsibilities in assisting the dealer?s claims administrator to properly code a harness repair. Failure to provide correct information may result in claims suspension or rejection. See this bulletin for further detail.

Reading this report

Complaint counts are reports filed with NHTSA, not failure rates. A common model collects more of them than a rare one that breaks more often.