Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
NTB09-131C
Service Bulletin/Repair Instructions
CERTIFICATION LABEL AND VIN PLATE REPLACEMENT SERVICE INFORMATION Because of collision damage or other vehicle repair, a replacement “Certification Label” or “VIN Plate/Label” may be needed. HINT: Certification Label = FMVSS (Federal Motor Vehicle Safety Standards) label. These items may be available from Nissan by request if certain criteria are met. This bulletin lists the criteria and provides an application form for such replacements. · The “VIN Plate/Label” (metal plate or vinyl label) is attached to the instrument panel or body on the driver side at the base of the windshield (see Figure 1). · The “Certification Label” (vinyl adhesive label) is located on the lower area of the driver side B-Pillar (see Figure 1).
NTB19-033G
Service Bulletin/Repair Instructions
INTELLIGENT CRUISE CONTROL INOPERATIVE AND AEB/FEB WARNING LIGHT ON OR RADAR OBSTRUCTION MESSAGE DISPLAYED WITH DTC C1A16 OR C2582 IF YOU CONFIRM IMPORTANT: The purpose of ACTION (on the next page) is to give you a quick idea of the work you will be performing. You MUST closely follow the entire SERVICE PROCEDURE as it contains information that is essential to successfully completing this repair. Nissan Bulletins are intended for use by qualified technicians, not 'do-it-yourselfers'. Qualified technicians are properly trained individuals who have the equipment, tools, safety instruction, and know-how to do a job properly and safely. NOTE: If you believe that a described condition may apply to a particular vehicle, DO NOT assume that it does. See your Nissan dealer to determine if this applies to your vehicle. The customer states that the ICC stopped working while driving, OR The customer states that the AEB/FEB warning light is ON, or turned ON, while driving (Figure 1), OR The message “Unavailable Front Radar Obstruction” or “Forward Driving Aids Temporarily Disabled Front Sensor Blocked See Owner's Manual” has displayed while driving (Figure 2). AND DTC C1A16, C1A16-97, C2582, or C2582-97 is the ONLY DTC stored. Figure 1 Figure 2 This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin. Forward Driving Aids Temporarily Disabled Front Sensor Blocked See Owner’s Manual
NTB19-042F
Service Bulletin/Repair Instructions
AUTOMATIC EMERGENCY BRAKING WARNING LIGHT BLINKING APPLIED SYSTEMS: Vehicles equipped with a lane camera (see Figure 1) SERVICE INFORMATION If the Automatic Emergency Braking (AEB) warning light or is blinking (but not illuminated steadily) or the customer states it is blinking, and there are no related DTCs, inspect the windshield. A blinking AEB warning light may occur under the following conditions: When contamination or foreign material adhere to the lane camera viewing window on the windshield. When driving while it is snowing or when frost forms on the lane camera viewing window on the windshield. When the lane camera viewing window on the windshield is temporarily fogged up. Figure 1 Nissan Bulletins are intended for use by qualified technicians, not 'do-it-yourselfers'. Qualified technicians are properly trained individuals who have the equipment, tools, safety instruction, and know-how to do a job properly and safely. NOTE: If you believe that a described condition may apply to a particular vehicle, DO NOT assume that it does. See your Nissan dealer to determine if this applies to your vehicle. HINT: o Refer to the applicable ESM for diagnosis if DTCs are present in the Laser/Radar, ICC/ADAS, or Lane Camera systems. o For further information: Refer to the following pages. Use the search keyword “blinking” in the ESM.
NTB23-023B
Service Bulletin/Repair Instructions
FLUID LEAK FROM THE FRONT DIFFERENTIAL CASE ACTUATOR MOTOR PLASTIC THREADS SERVICE INFORMATION Figure 1 Figure 2 If the front differential has a fluid leak coming from the actuator motor plastic threads (Figure 1): a. Place an alignment mark on the splined actuator body and the gear carrier (Figure 2). b. Remove the actuator and thoroughly clean the threads, making sure not to allow RTV to fall into the differential case. c. Once clean, apply Three Bond sealant to the threads, and then reinstall the actuator motor, making sure to line up the alignment marks. d. Check the front differential gear oil level and top to specification. o Refer to the ESM: TRANSMISSION & DRIVELINE > DRIVELINE > FRONT FINAL DRIVE: MA235/MA210 > PERIODIC MAINTENANCE > FRONT DIFFERENTIAL GEAR OIL DO NOT replace the front differential due to a fluid leak from the actuator motor plastic threads unless there has been consequential damage due to fluid loss (bearing failure or gear noise) to the front differential.
NTB19-071D
Service Bulletin/Repair Instructions
DTC B00A0-00 STORED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin. IF YOU CONFIRM DTC B00A0-00 (OCCUPANT DETECTION SENSOR UNIT) is stored, AND OCS zero point reset cannot be performed, (continued on the next page)
NTB20-085C
Service Bulletin/Repair Instructions
TELEMATICS CONTROL UNIT RESET AFTER AUTOMATIC COLLISION NOTIFICATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin. SERVICE INFORMATION The Telematics Control Unit (TCU) has the ability to send an automatic collision notification when the vehicle is involved in an accident. Once an automatic collision notification is performed, the function becomes disabled and the TCU must be reset to re-enable the automatic collision notification function. Some models will store DTC B2E1B-97 for “Automatic eCAll locked” as “CURRENT” when this function is disabled. This bulletin describes how to reset the TCU after an automatic collision notification has been performed. For models with B2E1B-97 for “Automatic eCAll locked” set as “CURRENT”, complete the SERVICE PROCEDURE starting on page 2, and then erase DTCs after confirming the TCU condition is “UNLOCK”.
NTB22-027B
Service Bulletin/Repair Instructions
DTC B2E01-96 (INTERNAL BATTERY) STORED AS CURRENT IN IVC This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin. SERVICE INFORMATION The APPLIED VEHICLES that come equipped with a factory installed SOS switch, located near the overhead map lamp, also come equipped with a wireless communication device called a Telematics Communication Unit (TCU). With an active NissanConnect® Services subscription, the TCU communicates with the Nissan Data Center to provide various security and convenience services. CONSULT has been updated to allow DTC B2E01-96 for “Internal battery” to be cleared in the TCU. If DTC B2E01-96 is Current/Active in the TCU, and no additional Current/Active DTCs are present in the TCU, perform the SERVICE PROCEDURE starting on page 2.
NTB20-077A
Service Bulletin/Repair Instructions
9 SPEED A/T VALVE BODY (CONTROL VALVE TCM) REPLACEMENT This bulletin is no longer active. Please discard previous versions of NTB20-077.
NTB23-031A
Service Bulletin/Repair Instructions
DTC B2E1B-06 (AUTOMATIC ECALL) STORED AS CURRENT IN THE IVC APPLIED VEHICLES: 2021-2022 Armada (Y62) 2022-2023 Frontier (D41) 2023 Kicks (P15) 2021-2023 Maxima (A36) 2022-2023 Pathfinder (R53) 2021, 2023 Rogue (T33) 2022-2023 Sentra (B18) 2020-2021, 2023 Titan/Titan XD (A61) 2023 Versa (N18) AMENDMENT HISTORY PUBLISHED DATE REFERENCE DESCRIPTION April 6, 2023 NTB23-031 Original bulletin published July 22, 2024 NTB23-031A Bulletin no longer active This bulletin is no longer active. Please discard previous versions of NTB23-031.
NTB10-066C
Service Bulletin/Repair Instructions
CAN COMMUNICATION CODES – DIAGNOSTIC TIPS AND GUIDELINES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB13-027D
Service Bulletin/Repair Instructions
CAN COMMUNICATION – NETWORK DIAGNOSTIC FLOW CHART This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB13-107G
Service Bulletin/Repair Instructions
VEHICLE KEY NOT DETECTED / AUTHENTICATED, ENGINE WILL NOT START This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB17-127C
Service Bulletin/Repair Instructions
INTELLIGENT KEY INITIALIZATION PROCEDURE STOPS OR WILL NOT CONTINUE This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.
NTB21-054B
Service Bulletin/Repair Instructions
REAR VIEW MONITOR OR NAVI SYSTEM ISSUES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB21-106B
Service Bulletin/Repair Instructions
DTC C1A17-49 OR C2580-49 STORED IN LASER/RADAR This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB23-044A
Service Bulletin/Repair Instructions
FALSE ACTIVATION OF AEB OR FCW This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB09-081K
Service Bulletin/Repair Instructions
WINDSHIELD CRACKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB13-028I
Service Bulletin/Repair Instructions
REMOVING FOREIGN MATERIAL FROM THE WINDOW GLASS This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB17-019H
Service Bulletin/Repair Instructions
WINDOW GLASS WARRANTY INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB19-042E
Service Bulletin/Repair Instructions
AUTOMATIC EMERGENCY BRAKING WARNING LIGHT BLINKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB23-018G
Service Bulletin/Repair Instructions
SOFTWARE UPDATE FOR INFOTAINMENT ISSUES This bulletin is no longer active. To access infotainment software updates via the Infotainment Software Update Utility: Select SPECIALTY TOOLS, and then select Infotainment Software Updates on the left side of ASIST. Please discard previous versions of NTB23-018.
NTB23-004A
Service Bulletin/Repair Instructions
MISSING OR CORRUPTED MAP DATA This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB23-018F
Service Bulletin/Repair Instructions
SOFTWARE UPDATE FOR INFOTAINMENT ISSUES This bulletin is no longer active. To access infotainment software updates via the Infotainment Software Update Utility: Select SPECIALTY TOOLS, and then select Infotainment Software Updates on the left side of ASIST. HINT: Initially, the Infotainment Software Update Utility will be available only on the CONSULT PC version of ASIST. The Utility will be added to ASIST WEB at a later date. Please discard previous versions of NTB23-018.
NTB24-007
Service Bulletin/Repair Instructions
DIAGNOSING REAR FINAL DRIVE ASSEMBLY LEAKS SERVICE INFORMATION If a Rear Final Drive Assembly (rear solid axle) is found to be leaking from one, or more, of the locations listed below, the source(s) of the leak should first be identified and, if possible repaired before the Rear Final Drive Assembly is considered for replacement. A Rear Final Drive Assembly should not be replaced unless bearing, gear, or other significant damage has occurred. Possible points of fluid leaks: ï· Front Oil Seal (Pinion Seal) ï· Axle Tube Seal ï· ABS Rear Wheel Sensor ï· Rear Axle Wheel Bearing Seal ï· Gear Carrier Cover Gasket ï· Drain Plug IMPORTANT: If a Rear Final Drive Assembly is found to have been replaced for a repairable leak and no internal damage is present, the claim will be charged back. Refer to pages 2-5 for additional information that illustrates and/or describes some, but not all, possible points where fluid leaks can occur, as well as helpful service HINTs. ï· This bulletin is only intended as a diagnostic reference and does not direct or imply repair. ï· Refer to the ESM for any applicable repair procedures, if needed.
NTB21-019C
Service Bulletin/Repair Instructions
FRONT MAP LAMP NOT WORKING OR SWITCH COMING APART This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB08-097L
Service Bulletin/Repair Instructions
DIAGNOSIS OF VEHICLE PULL (DRIFT) AND/OR STEERING WHEEL OFF-CENTER This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB23-018E
Service Bulletin/Repair Instructions
SOFTWARE UPDATE FOR INFOTAINMENT ISSUES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB23-018D
Service Bulletin/Repair Instructions
SOFTWARE UPDATE FOR INFOTAINMENT ISSUES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB23-049
Service Bulletin/Repair Instructions
12 VOLT BATTERY TESTING FOR IN-SERVICE VEHICLES SERVICE INFORMATION The following Service Information lists NNA procedural recommendations for establishing good connections while performing 12V battery testing. These recommendations are expected to promote uniformity during the connection process, therefore reducing the number of incorrect âTest with DCAâ and âReplaceâ results. HINT: If 12 volt batteries are allowed to discharge for a prolonged period of time, battery life may be drastically reduced. This condition may lead to premature battery replacement and customer dissatisfaction. IMPORTANT: ï· CPX-900 is now an accepted testing tool to use along with or in place of the DSS-5000 ï· CPX-900 operating instructions are found at: https://nissancpx900.midtronics.com/ ï· DSS-5000 operating instructions are found at: https://nissandss5000.midtronics.com/ ï· DCA-8000 is now a required testing tool to be used for all warranty replacement decisions. The DCA-8000 is also a more efficient charger than previously available, and will charge any available 12 volt lead acid battery safely and accurately as long as all precautions and inputs are made correctly. The DCA-8000 operating instructions are found at: https://nissandca8000.midtronics.com/
NTB23-053
Service Bulletin/Repair Instructions
SILICONE-BASED LUBRICANT OR GREASE CAN DAMAGE ELECTRICAL COMPONENTS SERVICE INFORMATION Do not apply Silicone-based lubricants or grease to, or around, any interior electrical components. To avoid the risk of death or severe personal injury, do not directly spray Silicone-based lubricant or grease, or inadvertently overspray Silicone-based lubricant or grease onto any interior electrical components. These types of lubricants can be detrimental to the proper operation of electrical components.
NTB23-044
Service Bulletin/Repair Instructions
FALSE ACTIVATION OF AEB OR FCW IF YOU CONFIRM The customer states they have experienced false activation and/or unexpected braking of the Automatic Emergency Braking (AEB) or Forward Collision Warning (FCW) system, AND There are no related DTCs stored. ACTION Follow the SERVICE PROCEDURE in this bulletin to: 1. Confirm the current ICC/ADAS part number. 2. Reprogram the ICC/ADAS, if applicable. 3. Configure the ICC/ADAS 4. Erase the DTCs.
NTB13-107F
Service Bulletin/Repair Instructions
VEHICLE KEY NOT DETECTED / AUTHENTICATED, ENGINE WILL NOT START This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB14-012I
Service Bulletin/Repair Instructions
REMOTE ENGINE START NOT WORKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB16-003C
Service Bulletin/Repair Instructions
INTELLIGENT KEY REPLACEMENT OR SWAPPING BETWEEN VEHICLES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.
NTB18-071C
Service Bulletin/Repair Instructions
SECURITY ALARM SOUNDS AFTER USING MECHANICAL KEY TO UNLOCK DRIVER DOOR This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB18-028B
Service Bulletin/Repair Instructions
RUNNING BOARD PROTECTIVE FILM RESIDUE This bulletin is no longer active. Please discard previous versions of NTB18-028.
NTB23-018C
Service Bulletin/Repair Instructions
SOFTWARE UPDATE FOR INFOTAINMENT ISSUES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB17-010B
Service Bulletin/Repair Instructions
STEP RAIL END CAP CHROME TRIM AVAILABLE AS SEPARATE PART This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB23-031
Service Bulletin/Repair Instructions
DTC B2E1B-06 (AUTOMATIC ECALL) STORED AS CURRENT IN IVC SERVICE INFORMATION The APPLIED VEHICLES that come equipped with a factory installed SOS switch, located near the overhead map lamp, also come equipped with a wireless communication device called a Telematics Communication Unit (TCU). With an active NissanConnect® Services subscription, the TCU communicates with the Nissan Data Center to provide various security and convenience services. 1. When diagnosing DTC B2E1B-06 (AUTOMATIC ECALL) on an APPLIED VEHICLE: ï· If DTC B2E1B-06 is not âCRNTâ in the IVC, DO NOT replace the TCU. Erase the DTC. No further steps are needed. ï· If DTC B2E1B-06 is âCRNTâ in the IVC, replace the TCU. o Refer to the ESM: REPAIR > DRIVER INFORMATION & MULTIMEDIA > AUDIO, VISUAL & NAVIGATION SYSTEM > REMOVAL AND INSTALLATION > TCU
NTB03-074Q
Service Bulletin/Repair Instructions
HEADLAMP, FOG LAMP, OR REAR COMBINATION LAMP FOGGING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB12-055J
Service Bulletin/Repair Instructions
CLICKING NOISE FROM FRONT OR REAR AXLE DURING TAKE-OFF/ACCELERATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB21-046C
Service Bulletin/Repair Instructions
SOFTWARE UPDATE FOR INFOTAINMENT ISSUES This bulletin has been superseded by: NTB23-018 SOFTWARE UPDATE FOR INFOTAINMENT ISSUES Please discard previous versions of this bulletin.
NTB22-047B
Service Bulletin/Repair Instructions
SOFTWARE UPDATE FOR INFOTAINMENT ISSUES This bulletin has been superseded by: NTB23-018 SOFTWARE UPDATE FOR INFOTAINMENT ISSUES Please discard previous versions of this bulletin.
NTB23-018B
Service Bulletin/Repair Instructions
SOFTWARE UPDATE FOR INFOTAINMENT ISSUES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB21-018A
Service Bulletin/Repair Instructions
REAR PERSONAL LAMP NOT WORKING OR SWITCH COMING APART This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB21-019B
Service Bulletin/Repair Instructions
FRONT MAP LAMP NOT WORKING OR SWITCH COMING APART This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB23-018A
Service Bulletin/Repair Instructions
SOFTWARE UPDATE FOR INFOTAINMENT ISSUES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB19-042D
Service Bulletin/Repair Instructions
AUTOMATIC EMERGENCY BRAKING WARNING LIGHT BLINKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB19-071C
Service Bulletin/Repair Instructions
DTC B00A0-00 STORED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB21-106A
Service Bulletin/Repair Instructions
DTC C1A17-49 OR C2580-49 STORED IN LASER/RADAR This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB10-145B
Service Bulletin/Repair Instructions
ABS/VDC CAN DIAGNOSIS INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB23-018
Service Bulletin/Repair Instructions
SOFTWARE UPDATE FOR INFOTAINMENT ISSUES SERVICE INFORMATION When diagnosing an infotainment issue or after replacement of the AV Control Unit, it is necessary to verify the current software version of the AV Control Unit to determine if a software version update is required. Use the vehicle tables in this bulletin to determine the current software version, if the AV Control Unit requires a software version update, and which procedure to use to update the AV Control Unit. The software updates in this bulletin are to address stability improvements and âbugâ fixes. IMPORTANT: If the customer is experiencing a software related concern, refer to NTB21-038 to verify if the customer concern is a hardware or software related issue. If the concern is a software related issue, review the information in this bulletin to update the AV Control Unit as needed.
NTB09-081J
Service Bulletin/Repair Instructions
WINDSHIELD CRACKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB13-028H
Service Bulletin/Repair Instructions
REMOVING FOREIGN MATERIAL FROM THE WINDOW GLASS This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB08-097K
Service Bulletin/Repair Instructions
DIAGNOSIS OF VEHICLE PULL (DRIFT) AND/OR STEERING WHEEL OFF-CENTER This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB10-126C
Service Bulletin/Repair Instructions
WHEEL BEARING COLLISION DAMAGE This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB20-010C
Service Bulletin/Repair Instructions
WINDSHIELD WIPER BLADE PERFORMANCE/DIAGNOSIS SERVICE INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB20-085B
Service Bulletin/Repair Instructions
TELEMATICS CONTROL UNIT RESET AFTER AUTOMATIC COLLISION NOTIFICATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB22-027A
Service Bulletin/Repair Instructions
DTC B2E01-96 (INTERNAL BATTERY) STORED AS CURRENT IN IVC This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB23-004
Service Bulletin/Repair Instructions
MISSING OR CORRUPTED MAP DATA IF YOU CONFIRM Customer states the error screen, shown in Figure 1, appears when using navigation. ACTION Follow the SERVICE PROCEDURE in this bulletin to download the map data from the ASIST Downloader, and then update the AV Control Unit with the map data.
NTB22-101
Service Bulletin/Repair Instructions
DRIVE SHAFT BOOT SERVICE INFORMATION SERVICE INFORMATION If a Drive Shaft (Axle Shaft) Boot on an APPLIED VEHICLE is found to be leaking grease, AND There is no abnormal noise or obvious CV Joint risk due to water intrusion and/or complete grease loss, check for REPAIR KIT-DUST BOOT (CV Joint Boot Kit) availability. ï· If there is a REPAIR KIT-DUST BOOT (CV Joint Boot Kit) available for the vehicle being repaired, do NOT replace the axle. Install a new boot kit following the procedure in the ESM. o Refer to the ESM: TRANSMISSION & DRIVELINE > FRONT AXLE > REMOVAL AND INSTALLATION > FRONT DRIVE SHAFT BOOT o If the complete axle (drive shaft) is replaced when only a new boot is required, the over-repair may be charged back to the dealer. ï· If there is NOT a REPAIR KIT-DUST BOOT (CV Joint Boot Kit) available for the vehicle being repaired, refer to the ESM for further diagnostic information. IMPORTANT: When servicing vehicles with staked axle nuts, refer to NTB21-013 to prevent Drive Shaft thread damage.
NTB20-029F
Service Bulletin/Repair Instructions
TELEMATICS (IVC) SERVICE INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.
NTB22-092
Service Bulletin/Repair Instructions
MIL ON WITH GEAR RATIO DTCS STORED IN THE TCM SERVICE INFORMATION If one or more of the following DTCs is stored in the TCM as current or past, please check Service COMM or Dealer Business Systems (DBS) National Service History to confirm if campaign R22B1 or R22A9 has been applied. ï· P0731 â 1GR INCORRECT RATIO ï· P0732 â 2GR INCORRECT RATIO ï· P0733 â 3GR INCORRECT RATIO ï· P0734 â 4GR INCORRECT RATIO ï· P0735 â 5GR INCORRECT RATIO ï· P0729 â 6GR INCORRECT RATIO ï· P076F â 7GR INCORRECT RATIO ï· P07D9 â 8GR INCORRECT RATIO ï· P07F6 â 9GR INCORRECT RATIO ï· P0893 â MULTIPLE GEARS ENGAGED 1. Has campaign R22B1 or R22A9 and the drive cycle (after performing the campaign) on page 2 of this bulletin already been completed? ï· No: a. Complete the related campaign. b. Perform the drive cycle on page 2, and then proceed to step 2. ï· Yes: Proceed to step 2. 2. If one or more of the DTCs, listed above are still being stored as current or past, refer to the ESM for further diagnostic information not covered by this bulletin.
NTB21-046B
Service Bulletin/Repair Instructions
SOFTWARE UPDATE FOR INFOTAINMENT ISSUES This bulletin has been superseded by: NTB22-047 SOFTWARE UPDATE FOR INFOTAINMENT ISSUES Please discard previous versions of this bulletin.
NTB22-047A
Service Bulletin/Repair Instructions
SOFTWARE UPDATE FOR INFOTAINMENT ISSUES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB21-086A
Service Bulletin/Repair Instructions
A/T WARNING LIGHT IS ON WITHOUT PAST OR CURRENT DTC STORED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB21-001B
Service Bulletin/Repair Instructions
TCM COMMUNICATION ERROR CAUSING A NO START CONDITION SERVICE INFORMATION If a customer states the engine will not crank and will not start (may be intermittent) and DTC U0101 (Lost Comm TCM) is stored in the ECU (ENGINE), and/or stored in the SCU (SHIFT) as PAST or CURRENT, OR The TCM shows as âUNKWNâ in the PRESENT column, or â0â in the PAST column, under the CAN DIAG SUPPORT MNTR tab in the ECU or SCU in C-III plus. ï· Please check Service COMM or Dealer Business Systems (DBS) National Service History to confirm if campaign R22B1 or R22A9 has been applied. 1. Has campaign R22B1 or R22A9 already been completed? No: Complete the related campaign bulletin. Yes: Proceed to step 2. 2. Refer to the ESM for further diagnostic information not covered by this bulletin. NOTE: If the Park indicator is not displayed in the Driver Information Center (Figure 1) and C-III plus does not display the current TCM part number after a 2 minute wait with the ignition ON, engine OFF, this TSB does not apply. Refer to the ESM for further diagnostic information. This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB21-028A
Service Bulletin/Repair Instructions
DELAYED ACCELERATION OR DELAYED UPSHIFT This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB22-074A
Service Bulletin/Repair Instructions
TRANSMISSION SHIFT QUALITY IMPROVEMENTS This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB22-074
Service Bulletin/Repair Instructions
TRANSMISSION SHIFT QUALITY IMPROVEMENTS IF YOU CONFIRM The customer has dissatisfaction with shifting during deceleration, when coming to a stop, during re-acceleration, or during acceleration from a complete stop, AND No TCM related DTCs are stored. ACTION Refer to the SERVICE PROCEDURE in this bulletin to: 1. Confirm the current ECM part number. 2. If applicable, reprogram the ECM. 3. Confirm the current TCM part number. 4. If applicable, reprogram the TCM.
NTB14-012H
Service Bulletin/Repair Instructions
REMOTE ENGINE START NOT WORKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB22-041
Service Bulletin/Repair Instructions
AV CONTROL UNIT SCREEN DELAMINATION IF YOU CONFIRM The AV Control Unit screen has signs of delamination. ACTION Replace the AV Control Unit.
NTB20-068A
Service Bulletin/Repair Instructions
TRANSFER CASE SEAL SERVICE PARTS This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB19-071B
Service Bulletin/Repair Instructions
DTC B00A0-00 STORED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB20-085A
Service Bulletin/Repair Instructions
TELEMATICS CONTROL UNIT RESET AFTER AUTOMATIC COLLISION NOTIFICATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB22-027
Service Bulletin/Repair Instructions
B2E01-96 (INTERNAL BATTERY) DTC STORED AS CURRENT IN IVC SERVICE INFORMATION CONSULT has been updated to allow DTC B2E01-96 (Internal battery) to be cleared in the Telematics Control Unit (TCU). If DTC B2E01-96 is Current/Active in the TCU, and No additional Current/Active DTCs are present in the TCU, perform the SERVICE PROCEURE starting on page 2.
PC884 2022 Titan
Service Bulletin/Repair Instructions
Tire Replacement Dealer Inventory *****Dealer Announcement***** Nissan is conducting a dealer inventory quality action to replace all five (5) tires (including spare tire) on 12 specific MY2022 Nissan Titan XD vehicles identified in Service Comm and National Service History â Open Campaigns. Due to a manufacturing concern, the tires may have been damaged when mounted on the rim. Affected vehicles are subject to stop sale and are either currently in dealer inventory or assigned and in transit to the dealer. *****What Dealers Should Do***** PLEASE FOLLOW THE ATTACHED INSPECTION INSTRUCTIONS: 1. Verify if vehicles are affected by this quality action using Service Comm or DBS National Service History â Open Campaigns I.D. PC884 ⢠New vehicles in dealer inventory can also be identified using DBS (Sales-> Vehicle Inventory, and filter by Open Campaign). ï§ Refer to NPSB 15-460 for additional information ⢠Please continue to check newly arriving inventory for campaign applicability. 2. Please do not drive, loan, sell or trade the specific vehicles in dealer inventory subject to this quality action. 3. Use the attached procedure to remedy any vehicles affected by this quality action prior to sale. 4. Once remedied, dealers should submit the applicable warranty claim for the action performed so it can be closed in Service Comm and release the vehicle for sale.
NTB22-026
Service Bulletin/Repair Instructions
SERVICE INFORMATION FOR FUEL GAUGE INACCURATE WITH DTCS STORED IN ECM SERVICE INFORMATION If a fuel level sensor has been diagnosed as sending an incorrect level signal, and one or more of the following DTCs are stored in the ECM, do not replace the entire âFuel Level Sensor Unit, Fuel Filter and Fuel Pump Assemblyâ (fuel pump assembly). The fuel level sensor can be replaced separately. ï· P0460 (FUEL LEV SEN SLOSH) ï· P0461 (FUEL LEVEL SENSOR) ï· P0462 (FUEL LEVL SEN/CIRC) ï· P0463 (FUEL LEVL SEN/CIRC) NOTE: Warranty claims referring to fuel level issues that result in the replacement of the entire fuel pump assembly will be charged back.
NTB22-020
Service Bulletin/Repair Instructions
SERVICE INFORMATION FOR BRAKE SWITCH ADJUSTMENT FOR DTC C1142 AND/OR C1116 STORED SERVICE INFORMATION DTC C1142 (PRESS SEN CIRCUIT) and/or C1116 (STOP LAMP SW) may be stored if the Stop Lamp Switch and/or the Brake Pedal Position Switch are out of adjustment. Before replacing any components for DTCs C1142 (PRESS SEN CIRCUIT) and/or C1116 (STOP LAMP SW), stored as past or current, confirm that the Stop Lamp Switch and the Brake Pedal Position Switch are properly adjusted. If either the Stop Lamp Switch and/or the Brake Pedal Position Switch are found to be out of adjustment, adjust them as per the ESM, and then clear the DTCs and perform DTC confirmation. ï· Refer to the ESM: BRAKES > BRAKE SYSTEM > PERIODIC MAINTENANCE > BRAKE PEDAL > Adjustment
NTB20-029E
Service Bulletin/Repair Instructions
TELEMATICS (IVC) SERVICE INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.
NTB13-027C
Service Bulletin/Repair Instructions
CAN COMMUNICATION â NETWORK DIAGNOSTIC FLOW CHART This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB17-127B
Service Bulletin/Repair Instructions
NISSAN; INTELLIGENT KEY INITIALIZATION PROCEDURE STOPS OR WILL NOT CONTINUE This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.
NTB18-071B
Service Bulletin/Repair Instructions
SECURITY ALARM SOUNDS AFTER USING MECHANICAL KEY TO UNLOCK DRIVER DOOR This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB21-011C
Service Bulletin/Repair Instructions
FALSE MAINTENANCE ALERT NOTIFICATION This bulletin is no longer active and has been superseded by NTB22-011. Please discard previous versions of NTB21-011.
NTB22-011
Service Bulletin/Repair Instructions
FALSE MAINTENANCE ALERT NOTIFICATION IF YOU CONFIRM The customer receives a Maintenance Alert from NissanConnect Services, notifying them that the oil pressure warning light or the service engine warning light is on, AND There are no warning lights ON in the instrument panel, AND There are no related DTCs stored. ACTION 1. Replace the Telematics Communication Unit (TCU). Ensure that the customer provides ALL Intelligent Keys for the vehicle before replacing the TCU. 2. Configure TCU.
NTB21-019A
Service Bulletin/Repair Instructions
FRONT MAP LAMP NOT WORKING OR SWITCH COMING APART This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB17-045C
Service Bulletin/Repair Instructions
CLEANING FRONT OR REAR COMBINATION LAMP ASSEMBLIES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB99-001F
Service Bulletin/Repair Instructions
STRUT AND SHOCK ABSORBER REPLACEMENT GUIDELINES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB21-106
Service Bulletin/Repair Instructions
DTC C1A17-49 OR C2580-49 STORED IN LASER/RADAR SERVICE INFORMATION If DTC C1A17-49 or C2580-49 is stored in LASER/RADAR in the âPASTâ column: ï· Erase the DTC. ï· DO NOT replace any parts. If DTC C1A17-49 or C2580-49 is stored in LASER/RADAR in the "CURRENT" column, refer to the applicable ESM for instructions.
NTB21-093
Service Bulletin/Repair Instructions
WATER INTRUSION INTO REAR COMBINATION LAMP CAN CAUSE MULTIPLE DTCS AND NO-START CONDITION SERVICE INFORMATION Water intrusion into one or both of the rear combination lamp assemblies can cause multiple DTCs, and possibly cause the vehicleâs engine to not start. Water intrusion into one or both rear combination lamp assemblies has been found to migrate through the harness, and can cause harness connector terminals in C1/E41 to corrode (Figure 1 on page 2). ï· Repair any damaged rear combination lamp assemblies immediately to avoid potential harness damage. Notice Harness connector terminals in C1/E41 found to be damaged through water intrusion due to a damaged rear combination lamp assembly is not warrantable.
NTB21-086
Service Bulletin/Repair Instructions
A/T WARNING LIGHT IS ON WITHOUT PAST OR CURRENT DTC STORED IF YOU CONFIRM The Automatic Transmission check warning light is ON, AND There are no TCM related DTCs stored that are PAST or CURRENT. ACTION 1. Confirm the current TCM part number. 2. Reprogram the TCM, if applicable. 3. Drive the vehicle and complete a transmission drive cycle. 4. Confirm that the A/T warning light does not come back ON. ï· See the Repair Overview on page 2.
NTB21-011A
Service Bulletin/Repair Instructions
FALSE MAINTENANCE ALERT NOTIFICATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB21-046A
Service Bulletin/Repair Instructions
SOFTWARE UPDATE FOR INFOTAINMENT ISSUES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB12-055H
Service Bulletin/Repair Instructions
CLICKING NOISE FROM FRONT OR REAR AXLE DURING TAKE-OFF/ACCELERATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB15-077D
Service Bulletin/Repair Instructions
SIGNAL TECH-II INTELLIGENT KEY BATTERY TEST AND SIGNAL CHECK This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB16-028D
Service Bulletin/Repair Instructions
INTELLIGENT KEY BUTTONS INOPERATIVE BUT REQUEST SWITCHES WORK This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB17-118B
Service Bulletin/Repair Instructions
NISSAN; INTELLIGENT KEY IDENTIFICATION AND REGISTRATION TIPS This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB21-046
Service Bulletin/Repair Instructions
SOFTWARE UPDATE FOR INFOTAINMENT ISSUES SERVICE INFORMATION When diagnosing an infotainment issue, always confirm that the latest software is installed in the AV control unit before starting the diagnosis. The software update in the following service procedure is to address the items below: ï· Stability improvements and âbugâ fixes. Refer to steps 1 - 4 to confirm that this bulletin applies.
NTB20-029D
Service Bulletin/Repair Instructions
TELEMATICS (IVC) SERVICE INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.
NTB21-001A
Service Bulletin/Repair Instructions
2020-2021 TITAN/TITAN XD; TCM COMMUNICATION ERROR CAUSING A NO START CONDITION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB21-018
Service Bulletin/Repair Instructions
2020-2021 TITAN/TITAN XD; REAR PERSONAL LAMP NOT WORKING OR SWITCH COMING APART IF YOU CONFIRM The rear personal (headliner) lamp operation is intermittent, Or The rear personal lamp switch and trim bezel assembly is coming apart and/or missing. ACTION Replace the rear personal lamp switch and trim bezel assembly.
NTB21-019
Service Bulletin/Repair Instructions
2020-2021 TITAN/TITAN XD; FRONT MAP LAMP NOT WORKING OR SWITCH COMING APART IF YOU CONFIRM The front map lamp operation is intermittent, Or The front map lamp switch and trim bezel assembly is coming apart and/or missing. ACTION Replace the front map lamp switch and trim bezel assembly.
NTB19-071A
Service Bulletin/Repair Instructions
DTC B00A0-00 STORED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB21-011
Service Bulletin/Repair Instructions
2020-2021 TITAN AND TITAN XD; FALSE MAINTENANCE ALERT NOTIFICATION HINT: The APPLIED VEHICLES are equipped with a wireless communication device called a Telematics Communication Unit (TCU). With an active NissanConnect Services⢠subscription, the TCU communicates with the Nissan Data Center to provide various security and convenience services. To determine if a vehicle is equipped with a TCU, look for the SOS button near the overhead map lamp. IF YOU CONFIRM The customer receives a Maintenance Alert from NissanConnect Services notifying them that the oil pressure warning light is on or that the service engine warning light is on, AND there are no warning lights ON in the instrument panel, AND there are no related DTCs stored. ACTION Update the TCU to the latest software version.
NTB99-001e
Service Bulletin/Repair Instructions
STRUT AND SHOCK ABSORBER REPLACEMENT GUIDELINES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB20-029c
Service Bulletin/Repair Instructions
2021 MAXIMA AND ROGUE, 2020-2021 TITAN AND TITAN XD; TELEMATICS (IVC) SERVICE INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.
NTB20-042b
Service Bulletin/Repair Instructions
2020-2021 TITAN AND TITAN XD; AV CONTROL UNIT REPLACEMENT PROCESS This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.
NTB20-029b
Service Bulletin/Repair Instructions
2021 MAXIMA AND ROGUE, 2020-2021 TITAN AND TITAN XD; TELEMATICS (IVC) SERVICE INFORMATION SERVICE INFORMATION The vehicles listed under APPLIED VEHICLES that come equipped with a factory installed SOS switch, located near the overhead map lamp, also come equipped with a wireless communication device called a Telematics Communication Unit (TCU). With an active NissanConnect Services⢠subscription, the TCU communicates with the Nissan Data Center to provide various security and convenience services. This bulletin contains important service procedures that must be performed properly in order to set up and maintain the telematics/in-vehicle communications (IVC) system for the vehicles listed under APPLIED VEHICLES. ï· A table has been provided, on the next page, that lists the steps required to successfully configure a TCU after it has been replaced. ï· A check-off sheet has been provided in this bulletin to print and check off steps as they are completed. Staple the completed check-off sheet to the repair order.
NTB20-042a
Service Bulletin/Repair Instructions
2020-2021 TITAN AND TITAN XD; AV CONTROL UNIT REPLACEMENT PROCESS IF YOU CONFIRM The AV control unit needs to be replaced on an APPLIED VEHICLE. ACTION IMPORTANT: The AV control unit for the Applied Vehicle is new, different from the previous model year, and requires a new procedure when replacing. If the following steps are not followed completely, all features will not work as intended. 1. Read and save the VIN 2. Read and save the configuration 3. Replace the AV control unit 4. Reprogram the AV control unit 5. Configure the AV control unit 6. Write the VIN to the AV control unit IMPORTANT: Procedures 4-6 above must be performed in the order shown below.
NTB21-001
Service Bulletin/Repair Instructions
2020-2021 TITAN/TITAN XD; TCM COMMUNICATION ERROR CAUSING A NO START CONDITION IF YOU CONFIRM The customer states the engine will not crank and will not start. (The incident may be intermittent.) And There is a U0101 DTC (Lost Comm TCM) in the Engine Control Unit (ECU) and/or the Shifter Control Unit (SCU). This DTC may be in a PAST or CURRENT status. Or The TCM shows âUNKWNâ in the PRESENT column or â0â in the PAST column under the CAN DIAG SUPPORT MNTR tab within the ECU (ENGINE) or the SCU (SHIFT) in CONSULT-III PLUS (C-III plus). See Figure 1 and Figure 2.
NTB18-028a
Service Bulletin/Repair Instructions
RUNNING BOARD PROTECTIVE FILM RESIDUE This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB20-088
Service Bulletin/Repair Instructions
2020-2021 TITAN/TITAN XD; HEADLAMP TURN SIGNAL BULB INOPERATIVE SERVICE INFORMATION When a âfront combination lampâ (headlamp) turn signal is found to be inoperative, first check the bulb for an open filament. If the bulb filament is open, only replace the bulb and do not replace the headlamp assy. ï· Headlamp replacement for this issue is subject to chargeback, and applies to both the halogen and LED headlamp. NOTE: Figure 1 is of a halogen front headlamp. The LED version is similar and has the turn signal bulb in the same location.
NTB20-085
Service Bulletin/Repair Instructions
TELEMATICS CONTROL UNIT RESET AFTER AUTOMATIC COLLISION NOTIFICATION SERVICE INFORMATION The Telematics Control Unit (TCU) has the ability to send an automatic collision notification when the vehicle is involved in an accident. Once an automatic collision notification is performed, the function becomes disabled. The TCU must be reset to re-enable the automatic collision notification function. This bulletin describes how to reset the TCU after an automatic collision notification has been performed.
NTB19-067d
Service Bulletin/Repair Instructions
SOFTWARE UPDATE FOR INFOTAINMENT ISSUES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.