Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
NTB09-131C
Service Bulletin/Repair Instructions
CERTIFICATION LABEL AND VIN PLATE REPLACEMENT SERVICE INFORMATION Because of collision damage or other vehicle repair, a replacement “Certification Label” or “VIN Plate/Label” may be needed. HINT: Certification Label = FMVSS (Federal Motor Vehicle Safety Standards) label. These items may be available from Nissan by request if certain criteria are met. This bulletin lists the criteria and provides an application form for such replacements. · The “VIN Plate/Label” (metal plate or vinyl label) is attached to the instrument panel or body on the driver side at the base of the windshield (see Figure 1). · The “Certification Label” (vinyl adhesive label) is located on the lower area of the driver side B-Pillar (see Figure 1).
NTB17-110A
Service Bulletin/Repair Instructions
2004 - 2015 TITAN; VIBRATION AT 40 – 50 MPH This bulletin is no longer active. Please discard previous versions of NTB17-110.
NTB10-066C
Service Bulletin/Repair Instructions
CAN COMMUNICATION CODES – DIAGNOSTIC TIPS AND GUIDELINES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB13-027D
Service Bulletin/Repair Instructions
CAN COMMUNICATION – NETWORK DIAGNOSTIC FLOW CHART This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB13-107G
Service Bulletin/Repair Instructions
VEHICLE KEY NOT DETECTED / AUTHENTICATED, ENGINE WILL NOT START This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB09-081K
Service Bulletin/Repair Instructions
WINDSHIELD CRACKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB13-028I
Service Bulletin/Repair Instructions
REMOVING FOREIGN MATERIAL FROM THE WINDOW GLASS This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB17-019H
Service Bulletin/Repair Instructions
WINDOW GLASS WARRANTY INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB08-097L
Service Bulletin/Repair Instructions
DIAGNOSIS OF VEHICLE PULL (DRIFT) AND/OR STEERING WHEEL OFF-CENTER This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB23-049
Service Bulletin/Repair Instructions
12 VOLT BATTERY TESTING FOR IN-SERVICE VEHICLES SERVICE INFORMATION The following Service Information lists NNA procedural recommendations for establishing good connections while performing 12V battery testing. These recommendations are expected to promote uniformity during the connection process, therefore reducing the number of incorrect âTest with DCAâ and âReplaceâ results. HINT: If 12 volt batteries are allowed to discharge for a prolonged period of time, battery life may be drastically reduced. This condition may lead to premature battery replacement and customer dissatisfaction. IMPORTANT: ï· CPX-900 is now an accepted testing tool to use along with or in place of the DSS-5000 ï· CPX-900 operating instructions are found at: https://nissancpx900.midtronics.com/ ï· DSS-5000 operating instructions are found at: https://nissandss5000.midtronics.com/ ï· DCA-8000 is now a required testing tool to be used for all warranty replacement decisions. The DCA-8000 is also a more efficient charger than previously available, and will charge any available 12 volt lead acid battery safely and accurately as long as all precautions and inputs are made correctly. The DCA-8000 operating instructions are found at: https://nissandca8000.midtronics.com/
NTB23-053
Service Bulletin/Repair Instructions
SILICONE-BASED LUBRICANT OR GREASE CAN DAMAGE ELECTRICAL COMPONENTS SERVICE INFORMATION Do not apply Silicone-based lubricants or grease to, or around, any interior electrical components. To avoid the risk of death or severe personal injury, do not directly spray Silicone-based lubricant or grease, or inadvertently overspray Silicone-based lubricant or grease onto any interior electrical components. These types of lubricants can be detrimental to the proper operation of electrical components.
NTB13-107F
Service Bulletin/Repair Instructions
VEHICLE KEY NOT DETECTED / AUTHENTICATED, ENGINE WILL NOT START This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB16-003C
Service Bulletin/Repair Instructions
INTELLIGENT KEY REPLACEMENT OR SWAPPING BETWEEN VEHICLES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.
NTB03-074Q
Service Bulletin/Repair Instructions
HEADLAMP, FOG LAMP, OR REAR COMBINATION LAMP FOGGING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB10-145B
Service Bulletin/Repair Instructions
ABS/VDC CAN DIAGNOSIS INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB09-081J
Service Bulletin/Repair Instructions
WINDSHIELD CRACKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB13-028H
Service Bulletin/Repair Instructions
REMOVING FOREIGN MATERIAL FROM THE WINDOW GLASS This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB08-097K
Service Bulletin/Repair Instructions
DIAGNOSIS OF VEHICLE PULL (DRIFT) AND/OR STEERING WHEEL OFF-CENTER This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB10-126C
Service Bulletin/Repair Instructions
WHEEL BEARING COLLISION DAMAGE This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB13-027C
Service Bulletin/Repair Instructions
CAN COMMUNICATION â NETWORK DIAGNOSTIC FLOW CHART This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB13-097J
Service Bulletin/Repair Instructions
EVAP LEAK DTC P0442, P0455, P0456 INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB17-082E
Service Bulletin/Repair Instructions
DTC P0456 CAUSED BY EVAP LEAK AT VENT CONTROL VALVE O-RING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB17-045C
Service Bulletin/Repair Instructions
CLEANING FRONT OR REAR COMBINATION LAMP ASSEMBLIES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB99-001F
Service Bulletin/Repair Instructions
STRUT AND SHOCK ABSORBER REPLACEMENT GUIDELINES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB13-106G
Service Bulletin/Repair Instructions
CORRECT OPERATION OF AUDIO CONTROLS AND BACK-UP CAMERA REQUIRES CONFIGURATION WITH C-III PLUS This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.
NTB15-036A
Service Bulletin/Repair Instructions
2010-2015 NISSAN; AUTO DOOR UNLOCK DOES NOT WORK This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.
NTB17-014A
Service Bulletin/Repair Instructions
BLUETOOTH, USB, AND AUX FUNCTION DIAGNOSTIC TOOL This bulletin has been amended. See AMENDMENT HISTORY on page 3. Please discard previous versions of this bulletin.
NTB12-099E
Service Bulletin/Repair Instructions
NAVIGATION WILL NOT WORK AFTER SD MAP CARD INSTALLED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.
NTB21-014
Service Bulletin/Repair Instructions
2012-2015 TITAN; HIGH-MOUNTED STOP LAMP SERVICE PART SERVICE INFORMATION The mounting stud diameter for the high-mounted stop lamp service part has changed from 5 mm to 6 mm. If, for any reason, the high-mounted stop lamp needs to be replaced, the mounting hole will need to be enlarged to 6.5 mm (¼ inch) as follows: 1. Remove the high-mounted stop lamp. ï· For high-mounted stop lamp removal, refer to the Electronic Service Manual: Section DRIVER CONTROLS > EXL â Exterior Lighting System > HIGH-MOUNTED STOP LAMP > Removal and Installation > HIGH-MOUNTED STOP LAMP. 2. Enlarge the high-mounted stop lampâs mounting holes (see Figure 1 on page 2) using a 6.5 mm (¼ inch) drill bit. To avoid damage to the vehicle, apply light pressure to the drill while drilling. Excessive force may cause the drill bit to penetrate too far and damage the headliner. 3. Apply touch-up paint to the mounting holes to protect the bare metal. 4. Install the new high-mounted stop lamp using M6 mounting nuts. Refer to the PARTS INFORMATION on page 2.
NTB99-001e
Service Bulletin/Repair Instructions
STRUT AND SHOCK ABSORBER REPLACEMENT GUIDELINES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB15-075b
Service Bulletin/Repair Instructions
2006-2015 TITAN; MIL ON WITH DTC P0448 This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB19-069a
Service Bulletin/Repair Instructions
TAKATA DRIVERS AIR BAG MODULE REPLACEMENT COLLECTION INITIATIVE This bulletin has been superseded by NTB20-023 or NTB20-024. Please discard previous versions of this bulletin.
REVISION 1 - PC7
Service Bulletin/Repair Instructions
Driver Airbag Module Field Quality Parts Collection Initiative UPDATE December 5, 2019 Please discard earlier versions of this bulletin The announcement from September 6, 2019 has been revised to include: o The part number listed in the parts section under âRelease Scheduleâ below has been revised to 98510-9GE9C
PC711 NV_Armada_
Service Bulletin/Repair Instructions
Driver Airbag Module Field Quality Parts Collection Initiative ***** Collection Initiative Summary ***** Nissan is conducting a special parts collection activity on certain 2012-2017 NV (F80), and 2013- 15 Armada (TA80) and Titan (A60) vehicles to replace the driver side airbag module free of charge. These vehicles are not subject to a recall. Instead, Nissan is collecting a limited number of modules for engineering study. Nissan will be notifying owners and asking them to participate in this important parts collection activity. As an incentive for participation, Nissan is offering a complimentary oil and filter change for participating customers. NOTE: Customers should be informed that this parts collection activity is time-limited. Once a sufficient number of in-use modules has been collected, this activity will end. ***** What Dealers Should Do**** 1. Verify if vehicles are eligible for this parts collection activity using Service Comm or DBS National Service History â Open Campaign I.D. PC711. 2. Dealers should use NTB19-069 to service any NV, Armada, and Titan vehicles subject to this activity. 3. The service department should submit the applicable warranty claim for the action(s) performed so the campaign can be closed on Service Comm and release the vehicle.
NTB19-069
Service Bulletin/Repair Instructions
TAKATA DRIVERS AIR BAG MODULE REPLACEMENT COLLECTION INITIATIVE INTRODUCTION Nissan is conducting this Takata Inflator Field Quality Parts Collection Initiative to replace the driver's air bag module. This service will be performed at no charge to the customer for parts or labor. As part of this initiative, a complementary engine oil and filter change may be performed. IDENTIFICATION NUMBER For this initiative, Nissan has assigned identification number PC711. The correct number must appear on all communications and documentation of any nature dealing with this initiative. DEALER RESPONSIBILITY Dealers are to repair vehicles falling within the range of this initiative that enter the service department. This includes vehicles purchased from private parties, vehicles presented by transient (tourists) owners, and vehicles in a dealerâs inventory.
NTB13-097g
Service Bulletin/Repair Instructions
ALL MODEL YEAR 2012 AND NEWER NISSAN VEHICLES; EVAP LEAK DTC P0442, P0455, P0456 INFORMATION This bulletin does NOT apply to LEAF vehicles and Titan XD vehicles with V8 diesel engine. This bulletin has been amended. See Amendment History on the last page. Please discard previous versions of this bulletin.
NTB17-082b
Service Bulletin/Repair Instructions
NISSAN; DTC P0456 CAUSED BY EVAP LEAK AT VENT CONTROL VALVE O-RING This bulletin does NOT apply to LEAF vehicles and Titan XD vehicles with V8 diesel engine. This bulletin has been amended. See Amendment History on the last page. Please discard previous versions of this bulletin.
NTB17-030a
Service Bulletin/Repair Instructions
NISSAN; FUEL TANK IS EXTREMELY DIFFICULT TO FILL This bulletin applies to Titan XD vehicles with a gas engine. The update below was sent out to Regions and Dealers in August of this year. We are re-circulating this update to make regional and dealer personnel aware that we are re-notifying customers at this time.
Revision 1-NEVAP
Service Bulletin/Repair Instructions
OBD II EVAP Tube Warranty Enhancement The update below was sent out to Regions and Dealers in August of this year. We are re-circulating this update to make regional and dealer personnel aware that we are re-notifying customers at this time.
NTB10-104c
Service Bulletin/Repair Instructions
TITAN, ARMADA, NV; ENGINE OIL LEAK AT RIGHT SIDE BLOCK BALL PLUG This bulletin has been amended. The APPLIED VEHICLES section has been updated. No other changes have been made. Please discard all previous versions of this bulletin.
NTB03-074m
Service Bulletin/Repair Instructions
FOG LAMP AND/OR HEADLAMP FOGGING This bulletin has been amended to add Fog Lamps and modify one step in the flow chart on page 3. No other changes have been made. Please discard previous versions of this bulletin.
NTB11-044c
Service Bulletin/Repair Instructions
WHEEL BALANCING SERVICE INFORMATION This bulletin has been amended. The publication date has been revised to include the latest models and model years. No other changes have been made. Please discard previous versions of this bulletin.
NTB18-003
Service Bulletin/Repair Instructions
2004-2015 TITAN; SQUEAK OR TICK NOISE FROM LEAF SPRINGS IF YOU CONFIRM: A squeak or tick noise coming from the rear suspension leaf springs when driving. NOTE: - Noise is more pronounced when driving over rough roads below 30 mph. - Chassis ears may be helpful to isolate this noise. - If the source of the squeak or tick noise is NOT either the left or right side leaf spring, this bulletin does not apply. Refer to ASIST for further diagnostic and repair information. ACTION: Clean the rear leaf spring tip inserts.
REVISION 3_P7318
Service Bulletin/Repair Instructions
Air Bag Control Unit Reprogram Voluntary Service Campaign UPDATE January 5, 2018 The announcement from October 6, 2017 has been revised: - Dealers may now use revised TSB NTB17-070 to resume repair of 2004-2006 model year vehicles. Please discard previous versions of this bulletin
NTB17-110
Service Bulletin/Repair Instructions
2004 - 2015 TITAN; VIBRATION AT 40 ? 50 MPH IF YOU CONFIRM A low frequency vibration at 40 ? 50 MPH AND The vehicle is equipped with the correct tires as shown on the TIRE AND LOADING INFORMATION LABEL on the driver side body side outer panel (B-pillar), (see Figure A). AND All 4 tires have been verified to be within specification for RH1 uniformity at or below 118 N (12 kg, 26.5 lbs.) as described in NTB11-062. ACTION Replace the 2 rearmost cab body mounts, nuts, and bolts with the new ones listed in the PARTS INFORMATION section of this bulletin.
P7318
Service Bulletin/Repair Instructions
Air Bag Control Unit Reprogram Voluntary Service Campaign UPDATE October 6, 2017 The announcement from August 15, 2017 has been revised to include: - Claims information for unintended airbag deployment (related to campaign) Temporary suspension of this campaign on all affected 2004-2006 model year vehicles is still in affect - Nissan is aware of reprogramming concerns on 2004-2006 models subject to P7318 Air Bag Control Unit Reprogramming and is working diligently with the supplier to provide a solution. - In the interim, Nissan recommends dealers suspend reprogramming activity on all 2004-2006 models until a software remedy is available. These models will continue to be identified in Service Comm and DBS National Service History with an open P7318 campaign. Nissan will provide an update as soon as revised software is available. Please discard previous versions of this bulletin
NTB11-044b
Service Bulletin/Repair Instructions
WHEEL BALANCING SERVICE INFORMATION This bulletin has been amended. The publication date has been revised to include the latest models and model years. No other changes have been made. Please discard previous versions of this bulletin.
NTB17-082a
Service Bulletin/Repair Instructions
NISSAN; DTC P0456 CAUSED BY EVAP LEAK AT VENT CONTROL VALVE O-RING This bulletin has been amended. The APPLIED VEHICLES and CLAIMS INFORMATION sections have been revised. No other changes have been made. Please discard previous versions of this bulletin.
REV1_P7318
Service Bulletin/Repair Instructions
Air Bag Control Unit Reprogram Voluntary Service Campaign Temporary suspension of this campaign on all affected 2004-2006 model year vehicles. Nissan is aware of reprogramming concerns on 2004-2006 models subject to P7318 Air Bag Control Unit Reprogramming and is working diligently with the supplier to provide a solution. In the interim, Nissan recommends dealers suspend reprogramming activity on all 2004-2006 models until a software remedy is available. These models will continue to be identified in Service Comm and DBS National Service History with an open P7318 campaign. Nissan will provide an update as soon as revised software is available. Please discard previous versions of this bulletin.
NTB17-082
Service Bulletin/Repair Instructions
NISSAN; DTC P0456 CAUSED BY EVAP LEAK AT VENT CONTROL VALVE O-RING IF YOU CONFIRM The MIL is ON in an APPLIED VEHICLE with DTC P0456 (EVAP VERY SML LEAK) AND - DTC P0456 is not caused by a loose fuel fill cap (refer to NTB13-097). - An EVAP leak has been detected where the vent control valve mounts to the canister. - The vent control valve O-ring seal is determined to be the cause. ACTION 1. DO NOT REPLACE the vent control valve. 2. Replace the vent control valve O-ring seal (O-ring). - Refer to SERVICE PROCEDURE on page 2.
P7318a
Service Bulletin/Repair Instructions
Air Bag Control Unit Reprogram Software Update Notice ***** Campaign Update***** Updated software has been released to ASIST at 3:00 PM Central Time to address concerns with some vehicles not being able to complete the reprogramming. This software will be released automatically overnight, but dealers can download the new software immediately by manually syncing their ASIST on their CONSULT III to acquire the latest updates.
P7318b
Service Bulletin/Repair Instructions
Air Bag Control Unit Reprogram Voluntary Service Campaign ***** Campaign Summary***** Nissan is committed to customer satisfaction. Nissan is conducting a Voluntary Service Campaign to reprogram the Air Bag Control Unit (ACU) in 2004-2014 Titan, 2005-2014 Frontier, and 2005-2014 Xterra vehicles. The current ACU rollover-sensing calibration logic could allow for unintended curtain air bag deployment in rare instances occurring under certain unique driving scenarios, usually involving unpaved roads or off-road where one side of the vehicle is higher than the other. The ACU reprogramming will improve rollover-sensing calibration to address certain unique driving scenarios, and help prevent unintended curtain air bag deployment, while maintaining the design intent for deployment in rollover crashes. Owners of affected vehicles will be notified beginning in June 2017 and asked to bring their vehicle to an authorized Nissan dealer to have the remedy work completed at no cost to the owner.
NTB17-071
Service Bulletin/Repair Instructions
VOLUNTARY SERVICE CAMPAIGN 2012-2014 TITAN, FRONTIER, AND XTERRA; AIR BAG DIAGNOSIS SENSOR UNIT INTRODUCTION Nissan is conducting a voluntary service campaign on certain specific model year 2012- 2014 Titan, Frontier, and Xterra vehicles to reprogram the air bag diagnosis sensor unit. This repair will be performed at no charge to the customer for parts or labor. IDENTIFICATION NUMBER Nissan has assigned identification number P7318 to this campaign. This number must appear on all communications and documentation of any nature dealing with this campaign. DEALER RESPONSIBILITY Dealers are to repair vehicles falling within range of this campaign that enter the service department. This includes vehicles purchased from private parties, vehicles presented by transient (tourists) owners, and vehicles in a dealer?s inventory.
NTB17-030
Service Bulletin/Repair Instructions
NISSAN; FUEL TANK IS SLOW OR DIFFICULT TO FILL IF YOU CONFIRM The fuel tank is slow or difficult to fill (filling nozzle shuts off before tank is full). IMPORTANT: Make sure this incident has been duplicated at a gas station by dealer service staff. ACTION Perform the Service Procedure in this bulletin, starting on the next page.
NTB17-026
Service Bulletin/Repair Instructions
BALL JOINT AXIAL END PLAY PROCEDURE SERVICE INFORMATION When working on the front suspension, use the updated service information in this bulletin along with the Electronic Service Manual (ESM). The updated information in this bulletin is a correction and a supplement to the ESM.
NTB14-068b
Service Bulletin/Repair Instructions
POWER MOONROOF INITIALIZATION SERVICE INFORMATION This bulletin has been amended. The APPPLIED VEHICES section and step 3 on page 3 have been revised. No other changes have been made. Please discard all previous versions.
NTB16-116
Service Bulletin/Repair Instructions
NISSAN; DIAGNOSIS INFORMATION FOR ABS DTC C1130 SERVICE INFORMATION When diagnosing for DTC C1130 (ENGINE SIGNAL): ECM related DTCs (P-codes) must be diagnosed, repaired, and DTCs erased first. - DTC C1130 is an ABS DTC that indicates an output signal of the ECM is not recognized. - Absent or incorrect ECM signals, that are indicated by corresponding P-codes, may trigger C1130 in the ABS control unit. - Some vehicle features that can be affected by absent or incorrect ECM signals are: - Forward Emergency Braking (FEB) - Intelligent Cruise Control (ICC) - VDC/ABS/TCS
NTB13-097D
Service Bulletin/Repair Instructions
ALL MODEL YEAR 2012 AND NEWER NISSAN VEHICLES; EVAP LEAK DTC P0442, P0455, P0456 INFORMATION THIS BULLETIN HAS BEEN AMENDED. THE TITLE HAS BEEN REVISED, AND THE BULLETIN NOW INCLUDES VEHICLES IN PRODUCTION AS OF THE DATE OF THIS UPDATE. NO OTHER CHANGES HAVE BEEN MADE. PLEASE DISCARD ALL PREVIOUS VERSIONS OF THIS BULLETIN.
NTB11027B
Service Bulletin/Repair Instructions
SERVICE INFORMATION Temporary tire Flat Spotting is common on New Dealer In-Stock vehicles that have not been occasionally moved. Flat Spotting can occur after the vehicle has been parked (not moved) for a few days, or longer. In most cases it is temporary. In extreme cases it can be permanent. Vehicles should be moved every 30 days, in one direction only, enough to rotate the tires 90° (see Figure 1). Moving vehicles as shown will prevent tire Flat Spotting. See this bulletin for further detail.
NTB14033B
Service Bulletin/Repair Instructions
SERVICE INFORMATION Replacement 5-speed rear wheel drive Automatic Transmission (A/T) assemblies and replacement control valves (valve bodies) now come with blank Transmission Control Modules (TCMs). Blank TCMs come without software and must be programmed (not reprogrammed) and then configured after they are installed. When ordering a replacement A/T or control valve, use the Nissan electronic parts information systems to obtain the correct software program part number See this bulletin for further detail.
NTB13106E
Service Bulletin/Repair Instructions
SERVICE INFORMATION If the configuration of the Audio/Navigation unit has not been completed correctly, some of the symptoms that may occur are: * Intermittent or no back up camera operation * No steering wheel switch response to audio inputs * No volume response from volume knob * Volume very loud or very quiet and adjustment is overly sensitive * Equalizer is adjusted so that Bass control is at maximum all the time * DTC U1000 for AVM C/U could be present If the above symptoms occur: * Confirm the configuration of the Audio/Navigation unit is correct. NOTE: Correct configuration of the appropriate control unit will restore correct operation. Audio/Navigation unit configuration is outlined starting on page 2. See this bulletin for further detail.
NTB09099A
Service Bulletin/Repair Instructions
IF YOU CONFIRM A refrigerant leak at a refrigerant pipe/hose joint location. ACTIONS 1. Inspect the metal surfaces of the pipe/hose joint for damage or contamination. NOTE: Do not replace a refrigerant pipe, hose, or other A/C component if an o-ring seal will solve the leak incident, if it should occur. 2. If no damage is found to the joint metal surfaces, replace the O-ring seal. See this bulletin for further detail.
NTB09131B
Service Bulletin/Repair Instructions
SERVICE INFORMATION Because of collision damage or other vehicle repair, a replacement "Certification Label" or "VIN Plate / Label" may be needed. These items may be available from Nissan by request if certain criteria are met. This bulletin lists the criteria and provides an application form for such replacements. See this bulletin for further detail.
NTB15-044B
Service Bulletin/Repair Instructions
Fuel Filler Cap tether clip service information
NTB15044B
Service Bulletin/Repair Instructions
SERVICE INFORMATION If the clip for the fuel filler cap tether becomes lost or is detached for any reason, it is no longer necessary to replace the fuel filler cap. The clip or "pin" is now available as a separate service part. NOTE - Do not replace the fuel filler cap if only the pin is needed. See this bulletin for further detail.
NTB03074J
Service Bulletin/Repair Instructions
SERVICE INFORMATION Occasionally customers may notice water vapor or fog in the headlamps. The information, illustrations, and flow chart in this bulletin are provided to help you in determining if an incident for water/condensation in the headlamps is normal or not. Nissan?s new vehicle limited warranty does not cover physically damaged (cracked or broken) headlamps. All current headlamp assemblies are vented to the atmosphere (not sealed). - This is necessary to allow for expansion and contraction of air from temperature "variations" (warmer or colder) without damage to the headlamp. - Moisture in the air sometimes "travels" into and out of the headlamp assembly through these vents. - Certain environmental conditions may cause moisture to condense. - The fogging/cloudiness should disappear over time when the headlamp is in a dry environment. See this bulletin for further detail.
NTB10104B
Service Bulletin/Repair Instructions
IF YOU CONFRIM An oil leak at the right side block ball plug behind the alternator. ACTION Use a punch to seat the block ball plug in the hole (refer to the Service Procedure). NOTE - Do not replace the engine block for this incident if it should occur. See this bulletin for further detail.
NTB09081C
Service Bulletin/Repair Instructions
SERVICE INFORMATION The purpose of this bulletin is to give Nissan dealers guidelines to help determine if windshield breakage is covered under warranty or is the customer?s responsibility. Nissan North America (NNA) is not responsible for damage to glass that is a result of objects striking or scratching the glass. However, NNA is responsible for manufacturing issues such as distorted glass and cracks that are due to improper installation or damage to the glass during vehicle assembly. NNA typically does not find any type of cracks in the windshield due to stress after the dealership PDI. See this bulletin for further detail.
NTB16003
Service Bulletin/Repair Instructions
SERVICE INFORMATION The Intelligent Keys used on the various Nissan vehicles may not be interchangeable between models and years. See this bulletin for further detail.
NTB09022G
Service Bulletin/Repair Instructions
SERVICE INFORMATION Design and process changes have been made to improve battery voltage at dealer receipt. Our goal is to deliver vehicles to customers with a 12 volt battery in excellent condition. Proper dealership storage and maintenance of vehicle 12 volt batteries is essential to insuring good battery operating life and customer satisfaction. Dealers are responsible for maintaining vehicles in their inventory. 12 volt batteries in vehicle inventory should always be kept at a full charge to prevent excessive discharge during storage and so they are ready for delivery to customers at any time. See this bulletin for further detail.
NTB13028A
Service Bulletin/Repair Instructions
SERVICE INFORMATION Windshield "foreign material" that is on the surface of the glass in some cases can be cleaned off with a very particular type and grade of steel wool. * Most any foreign material on the surface of the Windshield can be cleaned off by using #0000 super fine steel wool. >The #0000 grade super fine steel wool can be found in most hardware stores. Please see this bulletin for further details.
NTB14068A
Service Bulletin/Repair Instructions
SERVICE INFORMATION Power moonroof initialization procedures for the Applied Vehicles have been revised. The procedure described in this bulletin differs from the procedure in the Electronic Service Manual (ESM). At a later date and where possible, the applicable ESMs will be updated with the revised procedures. Follow the procedure in this bulletin should the power moonroof in an Applied Vehicle need to be initialized. See this bulletin for further details.
NTB12099D
Service Bulletin/Repair Instructions
SERVICE INFORMATION: The Navigation (NAVI) SD Map Data Cards are not interchangeable between the two versions of NAVI units offered in Nissan vehicles that use this type of map data. * If the wrong SD Map Data Card is used, the NAVI will display an update screen (Figures 1 and 2, reference only) and will only accept Cancel. * If this screen is displayed, install the correct SD Map Data Card, found in table A on page 2, and the NAVI unit will return to correct operation. See this bulletin for further detail.
NTB11069C
Service Bulletin/Repair Instructions
IF YOU CONFIRM The customer states HomeLink will not operate or has improper operation. ACTIONS 1. To significantly reduce unnecessary repairs, make sure: a. The vehicle is not in "Transit Mode" (if equipped). - Not in Transit Mode: With the turn signal switch is in the OFF (center) position, turn the ignition from OFF to ON. If the turn signal indicators stay OFF (do not illuminate), the vehicle is not in Transit Mode. b. The "Extended Storage Switch" (if equipped) is in the "Customer Delivery" position (pushed in). - The Extended Storage Switch is located on the fuse block that is located in the interior of the vehicle. 2. Confirm the customer is familiar with the HomeLink programming procedure located in the vehicle?s owner?s manual. 3. Test HomeLink operation with special tool HomeLink Transmitter Tester J-41540. See this bulletin for further detail.
NTB15075A
Service Bulletin/Repair Instructions
IF YOU CONFIRM: The MIL is ON with DTC P0448 (EVAP canister vent control valve close) stored in the ECM. ACTION: 1. Replace the EVAP canister (canister) and EVAP canister vent control valve (vent control valve). 2. Remove the canister filter. 3. Replace the fuel filler pipe and canister drain hose listed in PARTS INFORMATION. 4. Erase the DTC. Please see this bulletin for further details.
NTB13088A
Service Bulletin/Repair Instructions
SERVICE INFORMATION This bulletin has compiled Tire Pressure Monitor System (TPMS) and Low Tire Pressure Warning System (LTPWS) information for: - Basic diagnosing of TPMS/LTPWS systems - Radio frequency interference causing a "No Data" (C1708, C1709, C1710, C1711) condition - Sensor leaks - Moving TPMS/LTPWS wheel assemblies from one vehicle to another and TPMS/LTPWS sensor registration - Air pressure changes with altitude and ambient temperatures - Aftermarket tire sealers - Aftermarket wheels - Inflating/deflating tires with TPMS/LTPWS sensors See this bulletin for further detail.
NTB14057A
Service Bulletin/Repair Instructions
SERVICE INFORMATION The information in this bulletin is provided to help ensure correct diagnosis and repair of fluid leaks. All fluid leaks, when properly diagnosed, should be repaired (whether under warranty or customer pay) to ensure proper vehicle operation. However, certain normal operating conditions can be misdiagnosed as a leak requiring repair. Unnecessary repair or replacement of parts in connection with incorrectly diagnosed "leaks" can negatively impact customer satisfaction, be time consuming and costly, and if not performed correctly can lead to future repairs. See this bulletin for further detail.
NTB15060
Service Bulletin/Repair Instructions
SERVICE INFORMATION When servicing run flat tires or low profile tires: - Special equipment and procedures are required to avoid damage. - Specifically, Tire Pressure Monitor transmitters (TPMS sensors) can be damaged when improperly dismounting and mounting tires. - TPMS sensors becoming damaged during mounting or dismounting tires are not covered under warranty. - To avoid such damage, ensure that the tire changer being used and the operator of the tire changer is capable of servicing run flat and low profile tires. - Operator?s manuals for such tire changers must be followed. See this bulletin for further detail.
NTB15056
Service Bulletin/Repair Instructions
IF YOU CONFIRM One or more of the following DTCs are present: * P0139 - HO2S2 (B1) (Heated oxygen sensor 2 circuit slow response) * P0159 - HO2S2 (B2) (Heated oxygen sensor 2 circuit slow response) NOTE: Do not replace O2 sensors for the DTCs above if the vehicle?s current ECM part number is in TABLE A on page 5. ACTION 1. Refer to step 6 in the SERVICE PROCEDURE to confirm this bulletin applies to the vehicle you are working on. Please see this bulletin for further details.
NTB15055
Service Bulletin/Repair Instructions
SERVICE INFORMATION After ECM reprogramming, the Calibration Verification Number (CVN) needs to be automatically calculated prior to State emissions testing (also known as Inspection Maintainence, I/M, or SMOG testing depending upon location). Allowing the vehicle to idle for 22 minutes will allow for faster CVN calculation. It is recommended that customers utilize this method if the vehicle needs to be tested for emissions soon after ECM reprogramming. See this bulletin for further detail.
NTB15043
Service Bulletin/Repair Instructions
SERVICE INFORMATION The appearance of painted alloy wheels can be damaged if acidic cleaners are used. DO NOT use Chrome Wheel Cleaner on Painted Wheels. Many chrome wheel cleaners have acidic ingredients. Make sure to follow all instruction in the Appearance and Care Section of the Owner?s Manual. Damage to wheel appearance due to the use of inappropriate chemicals or cleaning products is not covered under warranty. See this bulletin for further detail.
NTB15036
Service Bulletin/Repair Instructions
SERVICE INFORMATION The applied vehicles are equipped with automatic door locks that lock all doors when the vehicle speed reaches 15 MPH. There is no instruction in the Owner?s Manual on auto-lock function deactivation. All doors unlock automatically when the ignition is placed in the OFF position (models with Intelligent Key system) or when the key is removed from the ignition switch (models without Intelligent Key system). The auto-unlock function can be deactivated by the driver in accordance with Owner?s Manual Instructions. Please see this bulletin for further details.
NTB15035
Service Bulletin/Repair Instructions
SERVICE INFORMATION If you confirm there is a need to replace the combination meter front cover (lens) on an Applied Vehicle for any reason (scratch, blemish, etc.): - Do not replace the entire combination meter assemby. The front cover of the combination meter assembly is available as a separate service part. - Refer to the Electronic Service Manual, section MWI-Meter, Warning Lamp & Indicator, for replacement information. See this bulletin for further detail.
NTB10112E
Service Bulletin/Repair Instructions
SERVICE INFORMATION For vehicles delivered to the dealers with wheel protector covers - Do not remove the wheel protector covers during Pre-Delivery Inspection (PDI) - Wheel protector covers help prevent cosmetic rotor corrosion. See this bulletin for further detail.
NTB99060G
Service Bulletin/Repair Instructions
SERVICE INFORMATION NOTE - Failure to follow the procedures in this bulletin may result in the denial of a warranty claim. In an effort to protect the paint finish, Paint Guard Film (PGF) is applied on many new Nissan vehicles. Paint Guard Film is a temporary white plastic protective film that is applied by the factory to the horizontal painted surfaces of the vehicle. The PGF protects the paint finish during vehicle handling, transportation and storage from harmful elements such as acid rain, iron particles, bird droppings, tree sap and other environmental contaminants. NOTE - Paint Guard Film CANNOT remain on the vehicle for more than six months after the vehicle's manufacture date. PGF must be removed at the end of six months. See this bulletin for further detail.
NTB12078A
Service Bulletin/Repair Instructions
SERVICE INFORMATION When diagnosing possible power steering gear (rack and pinion steering rack, or steering rack) leak issues, it may appear the steering rack is leaking when actually, it?s not. Use this service bulletin to help make a more accurate diagnosis of the steering rack. See this bulletin for further detail.
NTB00042D
Service Bulletin/Repair Instructions
SERVICE INFORMATION Changes or modifications to the front seat assembly trim materials may affect the proper operation of the Front Seat-Mounted Side-Impact Supplemental Air Bags and Passenger Occupant Classification Sensor and could result in serious personal injury or death. Nissan STRONGLY RECOMMENDS AGAINST making any change to seat trim materials from the factory equipped condition. This specifically applies to replacing the seat trim with non-factory materials; adding leather/cloth seat covers, seat pads, or seat storage pouches, etc. around or over the seat back and the passenger seat cushion. See this bulletin for further detail.
NTB13015A
Service Bulletin/Repair Instructions
SERVICE INFORMATION DTC B2190 (NATS ANTENNA AMP) can be stored for the following reasons: 1. Something other than an Intelligent Key is inserted into the Key-Slot. 2. An Intelligent Key issue. 3. A wiring issue between the Key-Slot and the BCM. 4. A Key-Slot issue. If DTC B2190 is stored due to 1 or 2 above, it will not erase, or go to "PAST", until a known good registered Intelligent Key is inserted into the Key-Slot. For DTC B2190 diagnosis; first perform the Service Manual DTC Confirmation Procedure. See this bulletin for further detail.
NTB14109
Service Bulletin/Repair Instructions
SERVICE INFORMATION Starting with 2010 Model Year, Nissan vehicles have been gradually incorporating a new type of DTC known as Permanent DTC or P-DTC. If a vehicle is equipped with P-DTCs, all emission related DTCs will also set a P-DTC if the MIL is turned ON. A listing of which DTCs that will also set a P-DTC is found in the DTC Index in the EC-Engine Control section of the Electronic Service Manual (ESM). If a DTC repair is performed and the DTC erased, a vehicle may fail an Emission Inspection and Maintenance test if the P-DTC is not also erased. See this bulletin for further detail.
NTB14107
Service Bulletin/Repair Instructions
SERVICE INFORMATION If a customer describes lack of power or poor acceleration, perform the following checks before attempting any repair: * Check for stored DTCs. * Check if the driver is resting their left foot on the brake pedal while accelerating. Advise the customer not to rest their foot on the brake while accelerating. * Use CONSULT-III plus in Engine Data Monitor to check operation of the brake lamp circuit signal. Monitor the brake switch during the incident; it should be "OFF". Please see this bulletn for further details.
NTB14081
Service Bulletin/Repair Instructions
SERVICE INFORMATION The Applied Vehicles in this bulletin are equipped with Automatic Door Lock and Automatic Door Unlock: IMPORTANT: Before performing any repairs on the automatic door lock/unlock system, review the operation of the system in the Owner?s Manual (Section 3; Pre-driving checks and adjustments, Doors, Automatic Door Locks. See this bulletin for further detail.
NTB14075
Service Bulletin/Repair Instructions
IF YOU CONFIRM - The customer describes the TPMS warning lamp flashes intermittently - One or more of the following TPMS DTCs are stored and are "current" : - C1710: [ NO-DATA]-RR, C1711: [ NO-DATA]-RL - The vehicle?s audio unit is non-NAVI equipped (no MAP button) but has a color monitor - The DTC related transmitter(s) (TPMS sensor or sensor) responds/tests as a good part with the hand held service tool Signal Tech II - (See this bulletin for additional confirmed conditions.) ACTION - Check the part number on the sensor(s): - If the part number stated in this bulletin is found on the sensor(s), replace all four (4) TPMS sensors with the one listed in the PARTS INFORMATION section of this bulletin. See this bulletin for further detail.
NTB-14-071
Service Bulletin/Repair Instructions
NISSAN: DUE TO LOW FRICTION COATING, USED ON REAR LEAF SPRING FRONT ATTACHMENT BOLT, WHICH CHANGED FROM 223N-M (164 FT-LBS) TO 102.5N-M (75.6 FT-LBS), FOR TORQUE SERVICE SPECIFICATION. MODEL 2014 TITAN. *PE
NTB14071
Service Bulletin/Repair Instructions
SERVICE INFORMATION The rear leaf spring front attachment bolt (see Figure 3) has been changed to use a low friction coating to reduce potential rear alignment shifting. The service specification for torque of the new bolt (Figure 2) has been changedfrom 223 N*m (164 Ft-lbs) to 102.5 N*m (75.6 Ft-lbs). If this bolt is removed or replaced as part of a service repair, and it is confirmed that this bolt has the new low friction coating, use only the new torque specification in Figure 2. Please see this bulletin for further details.
NTB14062
Service Bulletin/Repair Instructions
SERVICE INFORMATION If a customer requests to have an accessory engine cooling fan installed on their vehicle, follow the Service Tips contained in this bulletin.
NTB10066A
Service Bulletin/Repair Instructions
SERVICE INFORMATION Related to communication codes U1000, U1001, U1002, U1010: - Always diagnose the communication codes first. - When a module reports a U1000 code, it is typically operating normally; however, there is a communication error external to that module on the CAN network. - U1000 indicates an error. V-CAN diagram or CAN Diag Support Monitor provides data to determine the location of the error. See this bulletin for more information.
NTB14032
Service Bulletin/Repair Instructions
SERVICE INFORMATION Warranty claims coding for repairing wiring harnesses for all Nissan vehicles has changed. This bulletin gives an outline of the technician?s responsibilities in assisting the dealer?s claims administrator to properly code a harness repair. Failure to provide correct information may result in claims suspension or rejection. See this bulletin for further detail.
NTB08055C
Service Bulletin/Repair Instructions
SERVICE INFORMATION Information necessary to service the Supplemental Restraint System (SRS) safely is included in the "RESTRAINTS" section of the Electronic Service Manual (ESM) for each vehicle. IMPORTANT: Turn the ignition switch OFF, disconnect both battery terminals, and wait at least 3 minutes before performing any service on the SRS. See this bulletin for further detail.
NTB12091A
Service Bulletin/Repair Instructions
SERVICE INFORMATION Replacement Engine Control Modules (ECMs) for many newer Nissan vehicles are now "Blank" ECMs. Blank ECMs come without software and must be programmed (not reprogrammed) before they will function. See this bulletin for further detail.
NTB13110
Service Bulletin/Repair Instructions
IF YOU CONFIRM: The MIL is "ON" and one or both of the following DTCs are found stored in the ECM: * P117A * P117B AND * There are no drivability concerns. ACTION: * See this bulletin to confirm it applies and if so reprogram the ECM. Please see this bulletin for further details.
NTB-13-097
Service Bulletin/Repair Instructions
NISSAN: CERTAIN VEHICLES WOULD DISPLAY, IN THE INSTRUMENT CLUSTER, A WARNING LIGHT ILLUMINATION OF A LOOSE FUEL CAP WARNING. MODEL YEARS 2012-2014. NO MODELS LISTED. *PE
NTB-13-088
Service Bulletin/Repair Instructions
NISSAN: INFORMATION REGARDING TIRE PRESSURE MONITOR SYSTEM (TPMS) AND LOW TIRE PRESSURE WARNING SYSTEM (LTPWS) FOR SENSOR LEAKS, AIR PRESSURE CHANGES WITH ALTITUDE AND AMBIENT TEMPERATURES, AFTERMARKET WHEELS, RADIO FREQUENCY INTERFERENCE CAUSING NO DATA CONDITION AND INFLATING/DEFLATING TIRES WITH TPMS/LTPWS SENSORS. MODEL ALL. NO MODELS YEARS. *PE
NTB11005D
Service Bulletin/Repair Instructions
Two methods are used to update/upgrade Navigation Map Data: 1. The customer goes to www.nissannavigation.com and is mailed update disc(s) or SD Card and installs data, OR 2. The dealership is mailed update disc(s) and the customer must visit the dealership to have data installed. Use the matrix in this bulletin to determine which method is utilized for each Applied Vehicle. See this bulletin for further detail.
NTB92123D
Service Bulletin/Repair Instructions
Nissan Original Equipment or Genuine Accessory Alloy wheels, along with their finish coating (clear, chrome, titanium, etc.), are specifically developed to achieve Nissan design and performance standards. These Original Equipment or Genuine Accessory wheels are subjected to testing to ensure they meet Nissan's standards. Nissan Original Equipment Alloy or Genuine Accessory wheels subjected to aftermarket chroming may no longer continue to meet these standards and may be seriously damaged. Therefore, Nissan most strongly discourages, and recommends that these wheels NEVER be subjected to, aftermarket chroming. See this bulletinfor further detail.