Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
NTB09-131C
Service Bulletin/Repair Instructions
CERTIFICATION LABEL AND VIN PLATE REPLACEMENT SERVICE INFORMATION Because of collision damage or other vehicle repair, a replacement “Certification Label” or “VIN Plate/Label” may be needed. HINT: Certification Label = FMVSS (Federal Motor Vehicle Safety Standards) label. These items may be available from Nissan by request if certain criteria are met. This bulletin lists the criteria and provides an application form for such replacements. · The “VIN Plate/Label” (metal plate or vinyl label) is attached to the instrument panel or body on the driver side at the base of the windshield (see Figure 1). · The “Certification Label” (vinyl adhesive label) is located on the lower area of the driver side B-Pillar (see Figure 1).
NTB23-048A
Service Bulletin/Repair Instructions
DTC P17F4 STORED IN THE TCM IF YOU CONFIRM The customer reports transmission vibration when accelerating, HINT: Vibration occurs during quick reacceleration after braking, during a 2-1 downshift of the auxiliary gearbox. AND DTC P17F4 for “AUXILIARY GEARBOX (CL JUDDER)” is stored in the TCM. · If DTCs other than P17F4 are stored, this bulletin does not apply. Refer to the ESM for further diagnostic information. ACTION Refer to the Repair Overview on page 2 to determine if this bulletin applies. IMPORTANT: The purpose of ACTION (above) is to give you a quick idea of the work you will be performing. You MUST closely follow the entire SERVICE PROCEDURE as it contains information that is essential to successfully completing this repair.
NTB19-033G
Service Bulletin/Repair Instructions
INTELLIGENT CRUISE CONTROL INOPERATIVE AND AEB/FEB WARNING LIGHT ON OR RADAR OBSTRUCTION MESSAGE DISPLAYED WITH DTC C1A16 OR C2582 IF YOU CONFIRM IMPORTANT: The purpose of ACTION (on the next page) is to give you a quick idea of the work you will be performing. You MUST closely follow the entire SERVICE PROCEDURE as it contains information that is essential to successfully completing this repair. Nissan Bulletins are intended for use by qualified technicians, not 'do-it-yourselfers'. Qualified technicians are properly trained individuals who have the equipment, tools, safety instruction, and know-how to do a job properly and safely. NOTE: If you believe that a described condition may apply to a particular vehicle, DO NOT assume that it does. See your Nissan dealer to determine if this applies to your vehicle. The customer states that the ICC stopped working while driving, OR The customer states that the AEB/FEB warning light is ON, or turned ON, while driving (Figure 1), OR The message “Unavailable Front Radar Obstruction” or “Forward Driving Aids Temporarily Disabled Front Sensor Blocked See Owner's Manual” has displayed while driving (Figure 2). AND DTC C1A16, C1A16-97, C2582, or C2582-97 is the ONLY DTC stored. Figure 1 Figure 2 This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin. Forward Driving Aids Temporarily Disabled Front Sensor Blocked See Owner’s Manual
NTB19-042F
Service Bulletin/Repair Instructions
AUTOMATIC EMERGENCY BRAKING WARNING LIGHT BLINKING APPLIED SYSTEMS: Vehicles equipped with a lane camera (see Figure 1) SERVICE INFORMATION If the Automatic Emergency Braking (AEB) warning light or is blinking (but not illuminated steadily) or the customer states it is blinking, and there are no related DTCs, inspect the windshield. A blinking AEB warning light may occur under the following conditions: When contamination or foreign material adhere to the lane camera viewing window on the windshield. When driving while it is snowing or when frost forms on the lane camera viewing window on the windshield. When the lane camera viewing window on the windshield is temporarily fogged up. Figure 1 Nissan Bulletins are intended for use by qualified technicians, not 'do-it-yourselfers'. Qualified technicians are properly trained individuals who have the equipment, tools, safety instruction, and know-how to do a job properly and safely. NOTE: If you believe that a described condition may apply to a particular vehicle, DO NOT assume that it does. See your Nissan dealer to determine if this applies to your vehicle. HINT: o Refer to the applicable ESM for diagnosis if DTCs are present in the Laser/Radar, ICC/ADAS, or Lane Camera systems. o For further information: Refer to the following pages. Use the search keyword “blinking” in the ESM.
NTB20-066C
Service Bulletin/Repair Instructions
LANE CAMERA AIMING VEHICLE REFERENCE VALUES NOT IN ESM SERVICE INFORMATION If the lane camera requires aiming, the values in Table A on page 4 must be used. For all other models/model years, consult the Electronic Service Manual (ESM).
NTB19-071D
Service Bulletin/Repair Instructions
DTC B00A0-00 STORED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin. IF YOU CONFIRM DTC B00A0-00 (OCCUPANT DETECTION SENSOR UNIT) is stored, AND OCS zero point reset cannot be performed, (continued on the next page)
NTB10-066C
Service Bulletin/Repair Instructions
CAN COMMUNICATION CODES – DIAGNOSTIC TIPS AND GUIDELINES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB13-027D
Service Bulletin/Repair Instructions
CAN COMMUNICATION – NETWORK DIAGNOSTIC FLOW CHART This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB13-107G
Service Bulletin/Repair Instructions
VEHICLE KEY NOT DETECTED / AUTHENTICATED, ENGINE WILL NOT START This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB22-038C
Service Bulletin/Repair Instructions
RAB WARNING LIGHT ON IN INSTRUMENT PANEL AND/OR DTC B2724-23 STORED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB21-106B
Service Bulletin/Repair Instructions
DTC C1A17-49 OR C2580-49 STORED IN LASER/RADAR This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB09-081K
Service Bulletin/Repair Instructions
WINDSHIELD CRACKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB13-028I
Service Bulletin/Repair Instructions
REMOVING FOREIGN MATERIAL FROM THE WINDOW GLASS This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB17-019H
Service Bulletin/Repair Instructions
WINDOW GLASS WARRANTY INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB19-042E
Service Bulletin/Repair Instructions
AUTOMATIC EMERGENCY BRAKING WARNING LIGHT BLINKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB23-018G
Service Bulletin/Repair Instructions
SOFTWARE UPDATE FOR INFOTAINMENT ISSUES This bulletin is no longer active. To access infotainment software updates via the Infotainment Software Update Utility: Select SPECIALTY TOOLS, and then select Infotainment Software Updates on the left side of ASIST. Please discard previous versions of NTB23-018.
NTB20-016G
Service Bulletin/Repair Instructions
RADIO INTERMITTENTLY REBOOTS DURING AUDIO PLAYBACK VIA BLUETOOTH CONNECTED IPHONE This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB20-046G
Service Bulletin/Repair Instructions
VOLUME KNOB DOES NOT FUNCTION PROPERLY This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB20-080D
Service Bulletin/Repair Instructions
SOFTWARE UPDATE FOR INFOTAINMENT ISSUES This bulletin has been amended. See AMENDMENT HISTORY below. Please discard previous versions of this bulletin.
NTB22-033C
Service Bulletin/Repair Instructions
CLOCK INACCURATE AND/OR FREEZES This bulletin has been amended. See AMENDMENT HISTORY below. Please discard previous versions of this bulletin.
NTB23-018F
Service Bulletin/Repair Instructions
SOFTWARE UPDATE FOR INFOTAINMENT ISSUES This bulletin is no longer active. To access infotainment software updates via the Infotainment Software Update Utility: Select SPECIALTY TOOLS, and then select Infotainment Software Updates on the left side of ASIST. HINT: Initially, the Infotainment Software Update Utility will be available only on the CONSULT PC version of ASIST. The Utility will be added to ASIST WEB at a later date. Please discard previous versions of NTB23-018.
NTB08-097L
Service Bulletin/Repair Instructions
DIAGNOSIS OF VEHICLE PULL (DRIFT) AND/OR STEERING WHEEL OFF-CENTER This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB23-018E
Service Bulletin/Repair Instructions
SOFTWARE UPDATE FOR INFOTAINMENT ISSUES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB23-018D
Service Bulletin/Repair Instructions
SOFTWARE UPDATE FOR INFOTAINMENT ISSUES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB22-051B
Service Bulletin/Repair Instructions
HORN INOPERATIVE This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB22-038B
Service Bulletin/Repair Instructions
RAB WARNING LIGHT ON IN INSTRUMENT PANEL AND/OR DTC B2724-23 STORED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB23-049
Service Bulletin/Repair Instructions
12 VOLT BATTERY TESTING FOR IN-SERVICE VEHICLES SERVICE INFORMATION The following Service Information lists NNA procedural recommendations for establishing good connections while performing 12V battery testing. These recommendations are expected to promote uniformity during the connection process, therefore reducing the number of incorrect âTest with DCAâ and âReplaceâ results. HINT: If 12 volt batteries are allowed to discharge for a prolonged period of time, battery life may be drastically reduced. This condition may lead to premature battery replacement and customer dissatisfaction. IMPORTANT: ï· CPX-900 is now an accepted testing tool to use along with or in place of the DSS-5000 ï· CPX-900 operating instructions are found at: https://nissancpx900.midtronics.com/ ï· DSS-5000 operating instructions are found at: https://nissandss5000.midtronics.com/ ï· DCA-8000 is now a required testing tool to be used for all warranty replacement decisions. The DCA-8000 is also a more efficient charger than previously available, and will charge any available 12 volt lead acid battery safely and accurately as long as all precautions and inputs are made correctly. The DCA-8000 operating instructions are found at: https://nissandca8000.midtronics.com/
NTB23-053
Service Bulletin/Repair Instructions
SILICONE-BASED LUBRICANT OR GREASE CAN DAMAGE ELECTRICAL COMPONENTS SERVICE INFORMATION Do not apply Silicone-based lubricants or grease to, or around, any interior electrical components. To avoid the risk of death or severe personal injury, do not directly spray Silicone-based lubricant or grease, or inadvertently overspray Silicone-based lubricant or grease onto any interior electrical components. These types of lubricants can be detrimental to the proper operation of electrical components.
NTB23-048
Service Bulletin/Repair Instructions
DTC P17F4 STORED IN TCM IF YOU CONFIRM The customer reports transmission vibration when accelerating, HINT: Vibration occurs during quick reacceleration after braking, during a 2-1 downshift of the auxiliary gearbox. AND DTC P17F4 for âAUXILIARY GEARBOX (CL JUDDER)â is stored in the TCM. ï· If DTCs other than P17F4 are stored, this bulletin does not apply. Refer to the ESM for further diagnostic information. ACTION Refer to the Repair Overview on page 2 to determine if this bulletin applies.
NTB13-107F
Service Bulletin/Repair Instructions
VEHICLE KEY NOT DETECTED / AUTHENTICATED, ENGINE WILL NOT START This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB23-038
Service Bulletin/Repair Instructions
WARNING LIGHT ON WITH DTC C111F STORED AS CRNT IN THE ABS IF YOU CONFIRM DTC C111F (G-SENSOR) is stored as âCRNTâ in the ABS Actuator and Electric Unit (Control Unit). IMPORTANT: Do not replace the ABS control unit unless instructed to do so. ACTION Refer to the SERVICE PROCEDURE on page 2 to calibrate the Decel G-Sensor.
NTB14-012I
Service Bulletin/Repair Instructions
REMOTE ENGINE START NOT WORKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB16-003C
Service Bulletin/Repair Instructions
INTELLIGENT KEY REPLACEMENT OR SWAPPING BETWEEN VEHICLES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.
NTB23-018C
Service Bulletin/Repair Instructions
SOFTWARE UPDATE FOR INFOTAINMENT ISSUES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB03-074Q
Service Bulletin/Repair Instructions
HEADLAMP, FOG LAMP, OR REAR COMBINATION LAMP FOGGING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB20-016F
Service Bulletin/Repair Instructions
RADIO INTERMITTENTLY REBOOTS DURING AUDIO PLAYBACK VIA BLUETOOTH CONNECTED IPHONE This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB20-046F
Service Bulletin/Repair Instructions
VOLUME KNOB DOES NOT FUNCTION PROPERLY This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB20-080C
Service Bulletin/Repair Instructions
SOFTWARE UPDATE FOR INFOTAINMENT ISSUES This bulletin has been amended. See AMENDMENT HISTORY below. Please discard previous versions of this bulletin.
NTB22-033B
Service Bulletin/Repair Instructions
CLOCK INACCURATE AND/OR FREEZES This bulletin has been amended. See AMENDMENT HISTORY below. Please discard previous versions of this bulletin.
NTB12-055J
Service Bulletin/Repair Instructions
CLICKING NOISE FROM FRONT OR REAR AXLE DURING TAKE-OFF/ACCELERATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB23-018B
Service Bulletin/Repair Instructions
SOFTWARE UPDATE FOR INFOTAINMENT ISSUES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB23-018A
Service Bulletin/Repair Instructions
SOFTWARE UPDATE FOR INFOTAINMENT ISSUES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB19-042D
Service Bulletin/Repair Instructions
AUTOMATIC EMERGENCY BRAKING WARNING LIGHT BLINKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB19-071C
Service Bulletin/Repair Instructions
DTC B00A0-00 STORED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB21-106A
Service Bulletin/Repair Instructions
DTC C1A17-49 OR C2580-49 STORED IN LASER/RADAR This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB10-145B
Service Bulletin/Repair Instructions
ABS/VDC CAN DIAGNOSIS INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB23-018
Service Bulletin/Repair Instructions
SOFTWARE UPDATE FOR INFOTAINMENT ISSUES SERVICE INFORMATION When diagnosing an infotainment issue or after replacement of the AV Control Unit, it is necessary to verify the current software version of the AV Control Unit to determine if a software version update is required. Use the vehicle tables in this bulletin to determine the current software version, if the AV Control Unit requires a software version update, and which procedure to use to update the AV Control Unit. The software updates in this bulletin are to address stability improvements and âbugâ fixes. IMPORTANT: If the customer is experiencing a software related concern, refer to NTB21-038 to verify if the customer concern is a hardware or software related issue. If the concern is a software related issue, review the information in this bulletin to update the AV Control Unit as needed.
NTB09-081J
Service Bulletin/Repair Instructions
WINDSHIELD CRACKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB13-028H
Service Bulletin/Repair Instructions
REMOVING FOREIGN MATERIAL FROM THE WINDOW GLASS This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB22-021A
Service Bulletin/Repair Instructions
DTC P0746, P0776, P0841, P0965, P17F0 AND/OR P17F1 STORED IN THE TCM This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB08-097K
Service Bulletin/Repair Instructions
DIAGNOSIS OF VEHICLE PULL (DRIFT) AND/OR STEERING WHEEL OFF-CENTER This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB10-126C
Service Bulletin/Repair Instructions
WHEEL BEARING COLLISION DAMAGE This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB20-010C
Service Bulletin/Repair Instructions
WINDSHIELD WIPER BLADE PERFORMANCE/DIAGNOSIS SERVICE INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB22-051A
Service Bulletin/Repair Instructions
HORN INOPERATIVE This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB22-038A
Service Bulletin/Repair Instructions
RAB WARNING LIGHT ON IN INSTRUMENT PANEL AND/OR DTC B2724-23 STORED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB22-101
Service Bulletin/Repair Instructions
DRIVE SHAFT BOOT SERVICE INFORMATION SERVICE INFORMATION If a Drive Shaft (Axle Shaft) Boot on an APPLIED VEHICLE is found to be leaking grease, AND There is no abnormal noise or obvious CV Joint risk due to water intrusion and/or complete grease loss, check for REPAIR KIT-DUST BOOT (CV Joint Boot Kit) availability. ï· If there is a REPAIR KIT-DUST BOOT (CV Joint Boot Kit) available for the vehicle being repaired, do NOT replace the axle. Install a new boot kit following the procedure in the ESM. o Refer to the ESM: TRANSMISSION & DRIVELINE > FRONT AXLE > REMOVAL AND INSTALLATION > FRONT DRIVE SHAFT BOOT o If the complete axle (drive shaft) is replaced when only a new boot is required, the over-repair may be charged back to the dealer. ï· If there is NOT a REPAIR KIT-DUST BOOT (CV Joint Boot Kit) available for the vehicle being repaired, refer to the ESM for further diagnostic information. IMPORTANT: When servicing vehicles with staked axle nuts, refer to NTB21-013 to prevent Drive Shaft thread damage.
NTB22-018A
Service Bulletin/Repair Instructions
MANUAL FRONT SEAT DOES NOT MOVE FORWARD/REARWARD This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB12-055I
Service Bulletin/Repair Instructions
CLICKING NOISE FROM FRONT OR REAR AXLE DURING TAKE-OFF/ACCELERATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB22-033A
Service Bulletin/Repair Instructions
CLOCK INACCURATE AND/OR FREEZES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB14-012H
Service Bulletin/Repair Instructions
REMOTE ENGINE START NOT WORKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB22-051
Service Bulletin/Repair Instructions
HORN INOPERATIVE IF YOU CONFIRM The horn on an APPLIED VEHICLE is inoperative. ACTION Inspect the horn pad for a pinched ground wire. If a pinched ground wire is found, replace the high and low horns.
NTB22-038
Service Bulletin/Repair Instructions
RAB WARNING LIGHT ON IN INSTRUMENT PANEL AND/OR DTC B2724-23 STORED IF YOU CONFIRM The customer states an RAB warning light in the instrument panelâs information display is ON (Figure 1), AND/OR DTC B2724-23 (SONAR CONTROL UNIT - SONAR ECU INTERNAL FAILURE [UNDER VOLTAGE]) is stored. NOTE: A RAB warning light may appear in the vehicle information display. ACTION Reprogram and configure the Sonar Control Unit with the SERVICE PROCEDURE in this bulletin, if applicable.
NTB22-033
Service Bulletin/Repair Instructions
CLOCK INACCURATE AND/OR FREEZES SERVICE INFORMATION When diagnosing an infotainment issue, always confirm that the latest software is installed in the AV control unit before starting the diagnosis. The software update in the following service procedure is to address the items below: ï· Clock inaccurate ï· Clock freezes Refer to steps 1 - 5 on pages 3 - 4 to confirm that this bulletin applies.
NTB19-071B
Service Bulletin/Repair Instructions
DTC B00A0-00 STORED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB22-026
Service Bulletin/Repair Instructions
SERVICE INFORMATION FOR FUEL GAUGE INACCURATE WITH DTCS STORED IN ECM SERVICE INFORMATION If a fuel level sensor has been diagnosed as sending an incorrect level signal, and one or more of the following DTCs are stored in the ECM, do not replace the entire âFuel Level Sensor Unit, Fuel Filter and Fuel Pump Assemblyâ (fuel pump assembly). The fuel level sensor can be replaced separately. ï· P0460 (FUEL LEV SEN SLOSH) ï· P0461 (FUEL LEVEL SENSOR) ï· P0462 (FUEL LEVL SEN/CIRC) ï· P0463 (FUEL LEVL SEN/CIRC) NOTE: Warranty claims referring to fuel level issues that result in the replacement of the entire fuel pump assembly will be charged back.
NTB19-040H
Service Bulletin/Repair Instructions
DTC P0741/4/6, P0776, P0841, P0875, P0965, P2857/8/9, P17F0/1/2/4 AND/OR P285A STORED IN THE TCM, AND MAY HAVE HESITATION AND/OR REDUCED POWER This bulletin has been superseded. If one or more of the following DTCs is stored, refer to NTB22-021. ï· P0746 â PRESSURE CONTROL SOLENOID A ï· P0776 â PRESSURE CONTROL SOLENOID B ï· P0965 â PRESSURE CONTROL SOLENOID B ï· P17F0 â CVT JUDDER (T/M INSPECTION) ï· P17F1 â CVT JUDDER (C/V INSPECTION) ï· P285A â CLUTCH B PRESSURE ï· P0875 â T/M FLUID PRESS SENSOR/SWITCH D If one or more of the following DTCs is stored, refer to the ESM: ï· P0741 â TORQUE CONVERTER ï· P0744 â TORQUE CONVERTER ï· P0841 â TRANSMISSION FLUID PRESSURE SEN/SW A ï· P17F2 â CVT JUDDER (T/C INSPECTION) ï· P17F4 â AUXILIARY GEARBOX (CLUTCH JUDDER) ï· P2857 â CLUTCH A PRESSURE ï· P2858 â CLUTCH B PRESSURE ï· P2859 â CLUTCH A PRESSURE Please discard previous versions of this bulletin.
NTB22-021
Service Bulletin/Repair Instructions
DTC P0746, P0776, P0841, P0965, P17F0 AND/OR P17F1 STORED IN THE TCM IF YOU CONFIRM One or more of the following DTCs are stored: ï· P0746 â PRESSURE CONTROL SOLENOID A ï· P0776 â PRESSURE CONTROL SOLENOID B ï· P0841 â TRANSMISSION FLUID PRESSURE SEN/SW A ï· P0875 â T/M FLUID PRESS SENSOR/SWITCH ï· P0965 â PRESSURE CONTROL SOLENOID B ï· P17F0 â CVT JUDDER (T/M INSPECTION) ï· P17F1 â CVT JUDDER (C/V INSPECTION) ï· P17F2 â CVT JUDDER (T/C INSPECTION) ï· P2857 â CLUTCH A PRESSURE ï· P2858 â CLUTCH B PRESSURE ï· P2859 â CLUTCH A PRESSURE ï· P285A â CLUTCH B PRESSURE IMPORTANT: ï· If DTCs are stored other than those listed above, this bulletin does not apply. ï· If DTCs P17F0 and/or P17F1 are the only DTCs stored and there is no customer complaint of judder, this bulletin does not apply. ï· If ONLY P0875 T/M FLUID PRESS SENSOR/SWITCH is stored, refer to the ESM. ï· NTB20-060, 2018-2019 Kicks; Enhanced Diagnostic Logic For CVT, has reprogramming instructions that may apply. ACTION Refer to the REPAIR OVERVIEW on page 2.
NTB22-018
Service Bulletin/Repair Instructions
MANUAL FRONT SEAT DOES NOT MOVE FORWARD/REARWARD IF YOU CONFIRM A manual front seat (driver or passenger side) will not move forward/rearward with the Seat Adjustment Bar at the front of the seat pulled upward, AND One or both ends of the Seat Adjustment Bar are below the seat track tabs (Figure 1) displays one end of the Seat Adjustment Bar below the seat track tab and the other end above the seat track tab (with the seat removed from the vehicle). ACTION 1. Replace the Seat Adjustment Bar on the affected seat(s). ï· Refer to the SERVICE PROCEDURE of this bulletin for the repair procedure.
NTB13-027C
Service Bulletin/Repair Instructions
CAN COMMUNICATION â NETWORK DIAGNOSTIC FLOW CHART This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB13-097J
Service Bulletin/Repair Instructions
EVAP LEAK DTC P0442, P0455, P0456 INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB17-082E
Service Bulletin/Repair Instructions
DTC P0456 CAUSED BY EVAP LEAK AT VENT CONTROL VALVE O-RING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB20-046E
Service Bulletin/Repair Instructions
VOLUME KNOB DOES NOT FUNCTION PROPERLY This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB17-045C
Service Bulletin/Repair Instructions
CLEANING FRONT OR REAR COMBINATION LAMP ASSEMBLIES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB99-001F
Service Bulletin/Repair Instructions
STRUT AND SHOCK ABSORBER REPLACEMENT GUIDELINES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB21-106
Service Bulletin/Repair Instructions
DTC C1A17-49 OR C2580-49 STORED IN LASER/RADAR SERVICE INFORMATION If DTC C1A17-49 or C2580-49 is stored in LASER/RADAR in the âPASTâ column: ï· Erase the DTC. ï· DO NOT replace any parts. If DTC C1A17-49 or C2580-49 is stored in LASER/RADAR in the "CURRENT" column, refer to the applicable ESM for instructions.
PM996 2020 Kicks
Service Bulletin/Repair Instructions
Continuously Variable Transmission (CVT) Replacement Voluntary Emission Service Campaign Dealer Announcement: Nissan is conducting a Voluntary Emission Service Campaign to replace the Continuously Variable Transmission (CVT) on three (3) 2020 Nissan Kicks vehicle and one (1) 2020 Versa vehicles identified in Service Comm. Due to a manufacturing issue that has since been corrected, Nissan has determined that the installed CVT in the subject vehicles may not meet specification. What Dealers Should Do: 1.Verify if vehicles are affected by this Voluntary Emission Service Campaign using Service Comm or DBS National Service History â Open Campaigns I.D. PM996. 2.Dealers are requested to remedy any affected vehicles in dealer pre-owned inventory to ensure customer satisfaction. 3.Dealers should use NTB21-099 to correct any vehicles subject to this campaign. 4.Once repaired, dealers should submit the claim, using the claims coding provided, and release the vehicle.
NTB21-099
Service Bulletin/Repair Instructions
VOLUNTARY EMISSIONS SERVICE CAMPAIGN 2020 KICKS AND VERSA; CVT REPLACEMENT INTRODUCTION Nissan is conducting this voluntary emissions service campaign, on certain specific model year 2020 Kicks and Versa vehicles, to replace the CVT assembly. This service will be performed at no charge to the customer for parts or labor. IDENTIFICATION NUMBER Nissan has assigned identification number PM996 to this campaign. This number must appear on all communication and documentation of any nature dealing with this campaign. DEALER RESPONSIBILITY Dealers are to repair vehicles falling within range of this campaign that enter the service department. This includes vehicles purchased from private parties, vehicles presented by transient (tourists) owners, and vehicles in a dealerâs inventory.
NTB19-040G
Service Bulletin/Repair Instructions
DTC P0741/4/6, P0776, P0841, P0875, P0965, P2857/8/9, P17F0/1/2/4 AND/OR P285A STORED IN THE TCM, AND MAY HAVE HESITATION AND/OR REDUCED POWER This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB19-040F
Service Bulletin/Repair Instructions
DTC P0741/4/6, P0776, P0841, P0875, P0965, P2857/8/9, P17F0/1/2/4 AND/OR P285A STORED, AND MAY HAVE HESITATION AND/OR REDUCED POWER This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB12-055H
Service Bulletin/Repair Instructions
CLICKING NOISE FROM FRONT OR REAR AXLE DURING TAKE-OFF/ACCELERATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB21-049
Service Bulletin/Repair Instructions
MIL ON WITH DTC P0101 AND/OR P0507 STORED IN THE ECM IF YOU CONFIRM The MIL is ON and DTC P0101 (MAF SENSOR) and/or P0507 (ISC SYSTEM) is stored in the ECM. ACTION 1. Test the vehicle's 12 volt battery using the Midtronics DSS-5000. Recharge or replace the battery if necessary. 2. Erase all DTCs. 3. Perform Idle Air Volume Learning (IAVL).
NTB15-077D
Service Bulletin/Repair Instructions
SIGNAL TECH-II INTELLIGENT KEY BATTERY TEST AND SIGNAL CHECK This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB16-028D
Service Bulletin/Repair Instructions
INTELLIGENT KEY BUTTONS INOPERATIVE BUT REQUEST SWITCHES WORK This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB17-118B
Service Bulletin/Repair Instructions
NISSAN; INTELLIGENT KEY IDENTIFICATION AND REGISTRATION TIPS This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB19-118B
Service Bulletin/Repair Instructions
ALTIMA, KICKS AND VERSA SEDAN; DTC B26FE IN BCM AND KEY SYSTEM ERROR This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.
NTB21-027
Service Bulletin/Repair Instructions
MIL ON WITH DTC P062F AND/OR P0603 STORED IF YOU CONFIRM The MIL is ON and DTC P062F (EEPROM) and/or P0603 (ECM BACK UP/CIRCUIT) is stored, And The customer stated the vehicle was recently started after sitting for an extended period of time (i.e., the battery voltage was low while attempting to start the engine). ACTION 1. Test the vehicleâs 12 volt battery using the Midtronics DSS-5000. Recharge or replace the battery if necessary. 2. Erase all DTCs.
NTB19-118A
Service Bulletin/Repair Instructions
ALTIMA, KICKS AND VERSA SEDAN; DTC B26FE IN BCM AND KEY SYSTEM ERROR This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.
NTB19-040E
Service Bulletin/Repair Instructions
DTC P0741/4/6, P0776, P0841, P0965, P2857/8/9, P17F0/1/2/4 AND/OR P285A STORED, AND MAY HAVE HESITATION AND/OR REDUCED POWER This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB20-080B
Service Bulletin/Repair Instructions
SOFTWARE UPDATE FOR INFOTAINMENT ISSUES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB19-071A
Service Bulletin/Repair Instructions
DTC B00A0-00 STORED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB20-016E
Service Bulletin/Repair Instructions
RADIO INTERMITTENTLY REBOOTS DURING AUDIO PLAYBACK VIA BLUETOOTH CONNECTED IPHONE This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB21-013
Service Bulletin/Repair Instructions
PREVENT FRONT AXLE THREAD DAMAGE DURING NUT REMOVAL SERVICE INFORMATION If an Applied Vehicle needs to have a front axle nut removed, for any reason, the staking of the nut into the axle keyway must first be removed. The essential tool (part number # J-52982, Figure 1) required to remove the nut staking, is called out as a âCape Chiselâ in the Electronic Service Manual (ESM), and must be used to prevent thread damage to the axle (see Figure 2 on page 2). ï· The Cape Chisel arrived at dealers in December of 2020. ï· Damaged threads, due to improper removal of the stake placed in the nut, will not be covered by warranty. For information on using the Cape Chisel, refer to the Electronic Service Manual (ESM): Section TRANSMISSION & DRIVELINE > FRONT AXLE > REMOVAL AND INSTALLATION > FRONT DRIVE SHAFT > LH/RH.
NTB99-001e
Service Bulletin/Repair Instructions
STRUT AND SHOCK ABSORBER REPLACEMENT GUIDELINES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB20-016d
Service Bulletin/Repair Instructions
RADIO INTERMITTENTLY REBOOTS DURING AUDIO PLAYBACK VIA BLUETOOTH CONNECTED IPHONE This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB19-042b
Service Bulletin/Repair Instructions
AEB WARNING LIGHT BLINKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB20-046d
Service Bulletin/Repair Instructions
VOLUME KNOB DOES NOT FUNCTION PROPERLY This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB20-066b
Service Bulletin/Repair Instructions
LANE CAMERA AIMING VEHICLE REFERENCE VALUES NOT IN ESM This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB20-031a
Service Bulletin/Repair Instructions
KICKS AND VERSA SEDAN; INTELLIGENT KEY ERROR MESSAGE DISPLAYS AND DTC B2602 STORED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB20-080a
Service Bulletin/Repair Instructions
SOFTWARE UPDATE FOR INFOTAINMENT ISSUES This bulletin has been amended. See AMENDMENT HISTORY, below. Please discard previous versions of this bulletin.
NTB21-009
Service Bulletin/Repair Instructions
DTC B12A3-72 FOR FUEL PUMP RELAY STUCK OPEN SERVICE INFORMATION DTC B12A3-72 (Fuel Pump Relay Stuck Open) may be stored when the IPDM monitor circuit internally sees 0V to ground at pin #46. This is caused by an internal short to ground in the IPDM or one of the IPDM fuses listed below is open. If B12A3-72 is current or reoccurs after erasing DTCs, inspect the model specific fuse first. If the fuse is not open replace the IPDM. ï· Altima â Fuse # 58 (page 2) ï· Kicks â Fuse # 54 (page 3) ï· Versa â Fuse # 61 (page 4) For additional IPDM diagnostic information refer to the Electronic Service Manual (ESM): Section ELECTRICAL & POWER CONTROL > POWER CONTROL SYSTEM > IPDM E/R. See model specific fuse locations starting on page 2.
NTB18-042b
Service Bulletin/Repair Instructions
KICKS, LEAF, SENTRA AND VERSA; FRONT DOOR WILL NOT OPEN This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB20-016c
Service Bulletin/Repair Instructions
RADIO INTERMITTENTLY REBOOTS DURING AUDIO PLAYBACK VIA BLUETOOTH CONNECTED IPHONE This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
PM965 2020-21 Ve
Service Bulletin/Repair Instructions
Front Turn Signal Lamp Dealer Inventory Dealer Announcement Nissan is conducting a dealer inventory quality action to inspect both front turn signal lamp bulbs and, if necessary, replace them on 3,251 specific model year 2020 -2021 Versa vehicles identified in Service Comm. Due to a supplier concern that has since been resolved, the installed front turn signal bulbs may have durability issues that could cause them to not perform to specification. Affected vehicles are not subject to stop sale and are either currently in dealer inventory or assigned and in transit to the dealer. What Dealers Should Do PLEASE FOLLOW THE ATTACHED INSPECTION INSTRUCTIONS: 1.Verify if vehicles are affected by this quality action using Service Comm or DBS National Service History â Open Campaigns I.D. PM965 â¢New vehicles in dealer inventory can also be identified using DBS (Sales-> Vehicle Inventory, and filter by Open Campaign). ï§Refer to NPSB 15-460 for additional information â¢Please continue to check newly arriving inventory for campaign applicability. 2.Use the attached procedure to inspect the turn signal lamp bulb and, if necessary, remedy any vehicles affected by this quality action. â¢Parts may be ordered via normal parts ordering system beginning January 04, 2020. 3.The service department should submit the applicable warranty claim for the action performed so it can be closed on Service Comm. Dealer Responsibility It is the dealerâs responsibility to check Service Comm or DBS National Service History â Open Campaign using the appropriate campaign I.D for the inspection status on each affected vehicle currently in new vehicle inventory.
PM963 2020 Kicks
Service Bulletin/Repair Instructions
Continuously Variable Transmission (CVT) Replacement Dealer Announcement: Nissan is conducting a dealer inventory quality action to replace the Continuously Variable Transmission (CVT) on nine (9) 2020 Nissan Kicks vehicles and two (2) 2020 Versa vehicles identified in Service Comm. Due to a manufacturing issue that has since been corrected, Nissan has determined that the installed CVT in the subject vehicles may not meet specification. Affected vehicles are subject to stop sale and are either currently in dealer inventory or assigned and in transit to the dealer. What Dealers Should Do: PLEASE FOLLOW THE ATTACHED REPAIR INSTRUCTIONS: 1.Verify if vehicles are affected by this quality action using Service Comm or DBS National Service History â Open Campaign I.D. PM963 â¢New vehicles in dealer inventory can also be identified by using DBS (Sales-> Vehicle Inventory, and filter by Open Campaign). ï§Refer to NPSB 15-460 for additional information â¢Some vehicles may still be in transit. Please continue to check newly arriving inventory for QA Hold applicability. 2.Please do not drive, sell, loan, or trade the specific vehicles in Dealer Inventory subject to this Quality Action. â¢If an affected vehicle was previously traded, this information should be forwarded to the new dealer. 3.Use the Electronic Service Manual (ESM) to replace the Continuously Variable Transmission (CVT) prior to offering the vehicle for sale. â¢Parts will be orderable via normal ordering process beginning the first week of December. NOTE: Parts replaced under this campaign activity will be collected. Parts requested are VIN and repair order specific. It is important for dealers to return parts applicable to the VIN and repair order identified.
NTB20-016b
Service Bulletin/Repair Instructions
RADIO INTERMITTENTLY REBOOTS DURING AUDIO PLAYBACK VIA BLUETOOTH CONNECTED IPHONE This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB20-080
Service Bulletin/Repair Instructions
SOFTWARE UPDATE FOR INFOTAINMENT ISSUES SERVICE INFORMATION When diagnosing an infotainment issue, always confirm that the latest software is installed in the AV control unit before starting the diagnosis. The software update in the following service procedure is to address the items below: ï· Stability improvements and âbugâ fixes. ï· Android Auto skips while playing music. Refer to steps 1 - 4 to confirm that this bulletin applies. HINT: The update-software only needs to be downloaded once and then can then be used on multiple vehicles until other infotainment software is loaded onto the USB drive to overwrite the original data.
NTB19-042a
Service Bulletin/Repair Instructions
AEB WARNING LIGHT BLINKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB20-066a
Service Bulletin/Repair Instructions
LANE CAMERA AIMING VEHICLE REFERENCE VALUES NOT IN ESM This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB20-066
Service Bulletin/Repair Instructions
LANE CAMERA AIMING VEHICLE REFERENCE VALUES NOT IN ESM SERVICE INFORMATION If the lane camera requires aiming, the values in Table A on page 4 must be used. ï· For all other models/model years, consult the Electronic Service Manual (ESM). The following CONSULT-III plus (C-III plus) figures and steps are only provided to indicate where the VEHICLE REFERENCE VALUE from Table A is to be entered. The entire camera aiming procedure must be followed to complete the aiming procedure. ï· Refer to the ESM section: CRUISE CONTROL & DRIVER ASSISTANCE > DRIVER ASSISTANCE SYSTEM > DRIVER ASSISTANCE SYSTEM > BASIC INSPECTION > LANE CAMERA UNIT > CAMERA AIMING ADJUSTMENT. 1. Turn the ignition ON. 2. From the C-III plus home screen, select Diagnosis (One System).
NTB20-016a
Service Bulletin/Repair Instructions
RADIO INTERMITTENTLY REBOOTS DURING AUDIO PLAYBACK VIA BLUETOOTH CONNECTED IPHONE This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB20-031
Service Bulletin/Repair Instructions
KICKS AND VERSA SEDAN; INTELLIGENT KEY ERROR MESSAGE DISPLAYS AND DTC B2602 STORED IF YOU CONFIRM The Vehicle Information Display shows the message âIntelligent Key System Errorâ And DTC B2602 is found stored. NOTE: This incident usually occurs while driving the vehicle. ACTION Replace the Intelligent Key unit. ï· - If the vehicleâs current Intelligent Key unit part number is 285E1-5RB3A, replace it with 285E1-5EA0A. ï· - If the vehicleâs current Intelligent Key unit part number is 285E1-5RA6A, replace it with 285E1-5EA5A.
NTB19-040c
Service Bulletin/Repair Instructions
MIL ON WITH DTC P0741, P0744, P0746, P0776, P0841, P0965, P2857, P2858, P2859, AND/OR P285A STORED, AND MAY HAVE HESITATION AND/OR REDUCED POWER This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
PM941 2020 Versa
Service Bulletin/Repair Instructions
Inside Rearview Mirror Dealer Inventory *****Detailed Information***** Nissan is conducting a quality action on 2,732 MY2020 Versa (N18) vehicles identified in Service Comm to inspect the adhesion of the inside rearview mirror attachment and, if necessary, replace the windshield if the mirror detaches during inspection. Affected vehicles are subject to stop sale and are either currently in dealer inventory or assigned and in transit to the dealer. *****What Dealers Should Do***** PLEASE FOLLOW THE ATTACHED REPAIR INSTRUCTIONS: 1. Verify if vehicles currently in new dealer inventory are affected by this quality action using Service Comm or DBS National Service History â Open Campaign I.D. PM941 ï· - New vehicles in dealer inventory can also be identified using DBS (Sales-> Vehicle Inventory, and filter by Open Campaign). ï§ - Refer to NPSB 15-460 for additional information ï· - Please continue to check newly arriving inventory for campaign applicability. 2. Please do not drive, loan, sell or trade the specific vehicles in Dealer Inventory subject to this Quality Action. 3. Use the attached procedure to inspect and, if necessary, remedy any vehicles affected by this quality action: ï· - If the mirror and mounting plate does not detach from the windshield, during inspection, no repair is needed. ï· - If the inspection result is âNGâ (inside rearview mirror and mounting plate detaches): ï§ - Replace the windshield and aim the front camera unit using the procedure outlined in the Electronic Service Manual (ESM). ï· - Once vehicles have been inspected and, if necessary, remedied dealers may submit the applicable warranty claim for the action performed and the vehicle can be released for sale.
NTB20-016
Service Bulletin/Repair Instructions
RADIO INTERMITTENTLY REBOOTS DURING AUDIO PLAYBACK VIA BLUETOOTH CONNECTED IPHONE IF YOU CONFIRM The radio intermittently reboots while audio is played from a Bluetooth® connected iPhone. ACTION 1. Confirm the AV control unit software version. 2. Update the AV control unit software, if applicable.
PM938 2020 Versa
Service Bulletin/Repair Instructions
Rear Combination Lamps ***** Quality Action Summary ***** Nissan is conducting a quality action to clean and inspect the right and left rear combination lamps and, if necessary, replace the right, left, or both rear combination lamps (if crack is present) on specific MY2020 Versa vehicles identified in SERVICE COMM and National Service History â Open Campaigns. These vehicles are either currently in dealer inventory or assigned and in transit to the dealer. Chemical residue from the temporary exterior finish protection chemical used during handling, transportation, and storage could cause the combination lamps to crack. ***** What Dealers Should Do ***** PLEASE FOLLOW THE ATTACHED REPAIR INSTRUCTIONS: 1. Verify if vehicles currently in dealer inventory are affected by using Service Comm or National Service History â Open Campaign I.D. PM938. ï· - New vehicles in dealer inventory can also be identified using DBS (Sales->Vehicle Inventory, and filter by Open Campaign). ï§ - Refer to NPSB 15-460 for additional information ï· - Please continue to check newly arriving inventory for campaign applicability. 2. Use the attached procedure to clean, inspect and, if necessary, remedy any vehicles affected by this quality action prior to sale to ensure customer satisfaction. 3. Once remedied, dealers may submit the applicable warranty claim for the action performed and release the vehicle. ***** Dealer Responsibility ***** It is the dealerâs responsibility to check Service Comm or DBS National Service History â Open Campaign using the appropriate campaign I.D for the campaign status on each affected vehicle currently in new vehicle inventory. Thank you for your prompt attention to this matter.
EXPIRATION NOTIF
Service Bulletin/Repair Instructions
American Automobile Labeling Act (AALA) Labels â EXPIRATION NOTICE UPDATE February 21, 2020 Please discard earlier versions of this bulletin. Nissan announced the following quality action in October 2019. Service Comm will de-activate PM931 and PC713 on any un-remedied VINs on February 28, 2020. Nissan is still requesting that dealers apply the replacement label on any affected vehicles prior to sale. Please use the VIN list supplied with this announcement to identify applicable vehicles.
PM931 - Dealer I
Service Bulletin/Repair Instructions
PM931 - Dealer Inventory as of 2.20.2020
PM939 2020 Versa
Service Bulletin/Repair Instructions
MY20 Versa Quality Hold ***** Dealer Announcement ***** Nissan is committed to a high level of customer service and satisfaction. This commitment requires Nissan to periodically place certain vehicles on temporary Quality Assurance (QA) Hold to assure that these vehicles, as delivered to our customers, meet our exacting standards and our customersâ expectations. Effective immediately, Nissan is placing a temporary Quality Assurance (QA) Hold on eighteen (18) specific MY2020 Versa (N18) vehicles in dealer inventory. The fuel tank may not meet Nissan design specifications. Nissan engineering is investigating this potential issue and will provide the appropriate field action as quickly as possible. Affected vehicles are subject to stop sale and are either currently in dealer inventory or assigned and in transit to the dealer. ***** What Dealers Should Do ***** 1. Verify if vehicles are affected by this quality action using Service Comm or DBS National Service History â Open Campaigns I.D. PM939 ï· - New vehicles in dealer inventory can also be identified using DBS (Sales->Vehicle Inventory, and filter by Open Campaign). ï§ - Refer to NPSB 15-460 for additional information 2. Please do not drive, loan, sell or trade the specific vehicles in dealer inventory subject to this Quality Hold. 3. Nissan will provide an updated status, to include next steps, no later than the week ending February 28, 2020. Thank you for your prompt attention to this matter.
NTB19-118
Service Bulletin/Repair Instructions
ALTIMA, KICKS AND VERSA SEDAN; MIL ON WITH DTC B26FE IF YOU CONFIRM ï· A âKey System Errorâ message is displayed on the combination meter, And ï· DTC B26FE (IPDM - KEY SYSTEM ERROR) is stored in the BCM. ACTION 1. Disconnect the main power harness connector from the IPDM (E16 for Altima and E42 for Kicks and Versa Sedan). ï· - See Figure 1, Figure 2 and Figure 3 on the next page for IPDM main power harness connector locations. 2. Wait at least 20 seconds. 3. Reconnect the main power harness connector to the IPDM. 4. Confirm that the DTC is now past, and then erase the DTC. If the DTC will not erase, refer to the Electronic Service Manual for additional diagnostic information.
NTB19-040b
Service Bulletin/Repair Instructions
MIL ON WITH DTC P0741, P0744, P0746, P0776, P0841, P0965, P2857, P2858, P2859, AND/OR P285A STORED, AND MAY HAVE HESITATION AND/OR LACK OF POWER This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB18-059a
Service Bulletin/Repair Instructions
KICKS, SENTRA, AND VERSA; CVT FLUID LEAK SERVICE INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
REVISION 1 - PM9
Service Bulletin/Repair Instructions
American Automobile Labeling Act (AALA) Labels Dealer Inventory UPDATE October 25, 2019 Please discard earlier versions of this bulletin. The announcement from October 22, 2019 has been revised to include: ï· - Label shipments have been delayed and will resume next week. All shipments will be concluded by November 15, 2019.
PM931 2020 Versa
Service Bulletin/Repair Instructions
American Automobile Labeling Act Label Dealer Inventory ***** Campaign Summary ***** Nissan North America is conducting a Quality Action for dealers to replace the American Automobile Labeling Act (AALA) labels. The AALA label on affected vehicles was inadvertently printed with incorrect Engine manufacturing location and percentage breakdown of parts content by country. Affected vehicles are not subject to stop sale and are either currently in dealer inventory or assigned and in transit to the dealer. In the interest of customer satisfaction, Nissan requests dealers to apply the replacement label on the affected vehicles prior to retail sale. ***** What Dealers Should Do ***** 1. Verify if vehicles currently in new dealerâs inventory are affected by this quality action using Service Comm or DBS National Service History â Open Campaign I.D. ï§ - PM931 - Versa ï§ - PC713 - Titan ï· - New vehicles in dealer inventory can also be identified using DBS (Sales-> Vehicle Inventory, and filter by Open Campaign). ï§ - Refer to NPSB 15-460 for additional information ï· - Please continue to check newly arriving inventory for campaign applicability. 2. Use the attached procedure to remedy vehicles affected by this quality action. 3. The service department should submit the applicable warranty claim for the action(s) performed so it can be closed on Service Comm and release the vehicle. 4. Dealers will receive one (1) label for every affected vehicle in dealer inventory via USPS. Labels will be sent to the Service Managerâs attention. If replacement labels are needed, please send your request to: CampaignAnnouncements@-usa.com along with your dealer name, address, VIN, contact name and phone number. ï· - Labels will be mailed beginning October 23, 2019 and should arrive no later than October 25, 2019.
NTB19-071
Service Bulletin/Repair Instructions
DTC B00A0-00 STORED IF YOU CONFIRM DTC B00A0-00 (OCCUPANT DETECTION SENSOR UNIT) is stored And OCS zero point reset cannot be performed (continued on the next page) And The following screen displays: ACTION 1. Check the Occupant Classification System (OCS) control unit using the ODS Analysis tool software. ï· Refer to SERVICE PROCEDURE on page 5. HINT: âOCSâ may also be referred to as âODSâ. 2. Perform â75-zero RESETâ.