Vehicle report
Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
PIT3271K
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles. General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.
060089029Q
This informational bulletin provides information on interior cleaning products and what is offered to clean the interiors of GM vehicles.
040089015U
This bulletin provides information on Warranty Administration ? Required Operating Procedures - 8 Points (U.S. Only).
PIC5903C
This Preliminary Information communication provides information to the technician about vehicles that have Service Vehicle Soon Lamp or Check Engine Lamp is on. Technician may find Diagnostic Trouble Code P0534. Technician will use a scan tool to check for all Diagnostic Trouble Codes that are set, but should not delete any Diagnostic Trouble Codes found. Technician should also capture any Freeze Frame data in a Global Diagnostic System 2 Session Log. Technician will need to inspect the Rechargeable Energy Storage System and replace if it has three notches. On Volt and Ampera models check the Hybrid Processor Control Module 2 for having the latest software. Technician should update the Hybrid Processor Control Module 2 with the latest calibrations if need. If the module is up to date use Global Diagnostic System 2 to monitor the High and Low Side Refrigerant Pressures with the Air Conditioner Compress or Speed with the Heater-Vent-Air Conditioning temperature to maximum cold, high blower speed. Technician should follow published Service Information diagnostics if Diagnostic Trouble Code P0534 sets. If the technician finds both the High and Low Side Refrigerant Pressures are found to be low then connect the Refrigerant Recovery/Recharge Air Condition machine and check the Refrigerant level. Technician should follow ?Refrigerant Loss? in Service Information Diagnostics if the refrigerant level is less than 800 grams. When working on Spark Electric Vehicle technician should follow all published Service Information diagnostics before and other diagnostics or repairs. Technician should use the GE 50300 Refrigerant Recovery/Recharge Air Condition machine and check the R1234yf Refrigerant level. If the Refrigerant level is low technician should follow published Service Information diagnostics. If the Refrigerant level is over 500 grams technician will use Global Diagnostic System 2 to verify if the Remote Heater and Air Conditioning Module is up to date and update if n
PIP5267A
This Preliminary Information communication provides information to the technician about vehicles that may have a Check Engine Lamp or Service Vehicle Soon lamp on after charging. If the technician finds Diagnostic Trouble Codes P16C4 or P16C5 set in history, the Hybrid Powertrain Control Module will need to be reprogrammed. If the Diagnostic Trouble Codes are current or return and the Hybrid Powertrain Control Module and the Battery Charger Control Module have the current calibrations then processed to follow published Service Information diagnostics. This may lead to Battery Charger Control Module replacement.
PIC5920J
This Preliminary Information communication provides information to the technician about vehicles that will not charge and Service Engine Soon Malfunction Indicator Lamp on. Technician may find Diagnostic Trouble Codes P0AA6 and/ or a P1F0E set on 2011-2013 Volt or a P0DAA on 2014 Volt or Cadillac ELR in the Hybrid Powertrain Control Module 2.
PIC6089B
This Preliminary Information communication provides information to the technician about vehicles that may have a Battery Saver Message or red Battery Indicator displayed in the Driver Information Center. Technician may find Diagnostic Trouble Code P0AF8 set in history. Technician will need to the 12 volt battery using the GR8 Battery tester. The technician will need to perform the Direct current Power Conversion Test published in Global Service Information to check for maximum current and voltage output. This test requires the use of a Carbon Pyle load tester. In addition, the technician can select the 14V Power Module Control Function in the Engine Control Module and Accessory Power Module Setpoint in the Body Control Module by using the Scan Tool in order to check that the system is able to respond to current loads. If the test fails, if there were low voltage Diagnostic Trouble Codes or P0AF8 was set, the technician should confirm that the 200 amp fuse located in the X50D Fuse Block is torqued to correct specification. Technician should check the voltage on both sides of the 200 amp Fuse while there is a load applied and comparing the voltage readings. Voltage drop can be checked from the positive battery post to the Accessory Power Module side of the 200 amp fuse as well. If the Accessory Power Module will output current under a load but the voltage is low on both sides of the fuse when compared to the voltage output at the Accessory Power Module, check the following Service Information for any other Diagnostic Trouble Codes that may have led to the low voltage condition, Accessory Power Module output terminal is clean and torqued to specification, The Accessory Power Module output cable ring terminal is properly seated to the Accessory Power Module output terminal post and its condition, and test the voltage drop on the ground cables to the engine block, transmission, body and chassis to ensure they are within specification.
PIC5856F
This Preliminary Information communication provides information to the technician about vehicles that may have a Service Engine Soon Malfunction Indicator Lamp on. Technician may find a Diagnostic Trouble Codes P0C57, P0C58 and/or P0C62. When the technician has duplicated and is unable to find a repair after checking wiring and following normal diagnosis, please replace the Motor B Position Sensor to resolve the concern. Also insure that the Drive Motor Generator Control Module has the latest calibration.
PIC5920H
This Preliminary Information communication provides information to the technician about vehicles that will not charge and Service Engine Soon Malfunction Indicator Lamp on. Technician may find Diagnostic Trouble Codes P0AA6 and/ or a P1F0E set on 2011-2013 Volt or a P0DAA on 2014 Volt or Cadillac ELR in the Hybrid Powertrain Control Module 2.
PIC5921B
This Preliminary Information communication provides information to the technician about vehicles that are unable to charge the hybrid battery and the malfunction Indicator lamp is illuminated on the Instrument Panel Cluster. Technician may find a current or history code P16C1 or P16C2 set in the Battery Charging Control Module. Technician should update the Battery Charging Control Module with the latest software in Tis 2 Web. If the technician experiences any issues while programming the Battery Charging Control Module, please contact Techline for further assistance.
PIP5463A
This Preliminary Information communication provides information to the technician about vehicles that have a Malfunction Indicator Lamp on and may have a loss of propulsion. Technician may find Diagnostic Trouble Code P0604 set in the Hybrid Powertrain Control Module Technician will need to replace the (T6) Power Inverter Module.
PIC5978B
This Preliminary Information communication provides information to the technician about vehicles that have Diagnostic Trouble Code P0606 during normal vehicle servicing procedures such as clearing codes or connecting the 12 volt battery. To clear the Diagnostic Trouble Code technician will need to close all doors and rear hatch, press and hold the power button to put the vehicle into service mode, clear the Diagnostic Trouble Code using Global Diagnostic System 2, Power off the vehicle, open and close the driver?s door, wait one minute, and start vehicle and ensure Malfunction Indicator Lamp is not illuminated.
PIC6292B
This Preliminary information communicates that a Propulsion Power is reduced message occurs during regular operation, and there are no DTCs present, then contact GM Technical Assistance for direction
PIP4891H
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on. Technician may find Diagnostic Trouble Code P0497 stored. Technician will inspect all Evaporative Emissions System components and replace any component that is saturated with liquid fuel. Also Evaporative Emissions System lines should be blown out. Insure the customer is aware that over filling the fuel tank may lead to a repeat concern.
PIP4870D
This Preliminary Information communication provides information to the technician about vehicles that may have a engine noise is sometimes louder than expected. Also will explain the known normal and abnormal reasons why the engine may be louder. When the vehicle speed is between 25-50 miles per hour the road noise does not mask the engine noise this is considered normal. When the vehicle is first started for the day the system will perform a catalyst preconditioning for about a minute. At this time the engine will seem louder than normal, this is normal. At times the engine often runs at wide open throttle, but at a reduced speed. This sound is uncharacteristic of a four-cylinder engine in a traditional sedan, but is a characteristic of an extended range electric vehicle such as the Chevrolet Volt. Technician will be able to inspect for abnormal induction ground-out conditions. These locations should be checked lower rubber isolator on air box not installed correctly or missing, upper induction resonator cover not installed properly, refrigerant line not bolted to engine support bracket, and throttle body contacting coolant pipes behind it. Abnormal exhaust ground-out conditions should also be inspected. These locations are at the exhaust clamp rearward of the second catalytic converter is contacting the battery heat shield, exhaust resonator underbody is contacting the heat shield. Repair any abnormal issue found.
PIP4869F
This Preliminary Information communication provides information to the technician about vehicles that display a ?Propulsion Power is Reduced? in the Driver Information Center when driving in the mountains. Dealer should advise the customer the vehicle should be placed in Mountain Mode on the vehicle when the vehicle has a full charge if their travel plans involve mountainous driving before the next charge event.
PIC5414J
This Preliminary Information communication advises the technician what affects electric range and provides driving tips for better energy efficiency. Vehicles may have an electric range is less than customer expectations or what is being displayed on the in-vehicle display for EV range.
PIP4869E
This Preliminary Information communication provides information to the technician about vehicles that display a ?Propulsion Power is Reduced? in the Driver Information Center when driving in the mountains. Dealer should advise the customer the vehicle should be placed in Mountain Mode on the vehicle when the vehicle has a full charge if their travel plans involve mountainous driving before the next charge event.
PIP4859E
This Preliminary Information communication provides information to the technician on the steps to vacuum fill to ensure the cooling system is properly filled. Technician will need to use special tool GE-47716 Vac-N-Fill Coolant Refill Tool. Technician will also perform Hybrid/EV Battery Pack Coolant Pump Bleed Procedure in the GDS2 tool. After performing the GDS2 coolant bleed procedure drive vehicle for approximately 5 miles in a slalom type of situation to purge any remaining air from battery pack cooling plates.
PIP5081L
This Preliminary Information communication provides information to the technician about vehicles that may have whistle, scrape or whine type noise while driving that may be more noticeable during regenerative braking. Technician may find this noise emanating from the left side of the drive unit. The tech may also state that the vehicle has a current or history diagnostic trouble code P0A46. The noise may be caused by the drive motor rotor bearing cage separated. Technician should replace the bearing with the new updated part number.
PIC5903B
This Preliminary Information communication provides information to the technician about vehicles that have Service Vehicle Soon Lamp or Check Engine Lamp is on. Technician may find Diagnostic Trouble Code P0534. Technician will use a scan tool to check for all Diagnostic Trouble Codes that are set, but should not delete any Diagnostic Trouble Codes found. Technician should also capture any Freeze Frame data in a Global Diagnostic System 2 Session Log. Technician will need to inspect the Rechargeable Energy Storage System and replace if it has three notches. On Volt and Ampera models check the Hybrid Processor Control Module 2 for having the latest software. Technician should update the Hybrid Processor Control Module 2 with the latest calibrations if need. If the module is up to date use Global Diagnostic System 2 to monitor the High and Low Side Refrigerant Pressures with the Air Conditioner Compress or Speed with the Heater-Vent-Air Conditioning temperature to maximum cold, high blower speed. Technician should follow published Service Information diagnostics if Diagnostic Trouble Code P0534 sets. If the technician finds both the High and Low Side Refrigerant Pressures are found to be low then connect the Refrigerant Recovery/Recharge Air Condition machine and check the Refrigerant level. Technician should follow ?Refrigerant Loss? in Service Information Diagnostics if the refrigerant level is less than 800 grams. When working on Spark Electric Vehicle technician should follow all published Service Information diagnostics before and other diagnostics or repairs. Technician should use the GE 50300 Refrigerant Recovery/Recharge Air Condition machine and check the R1234yf Refrigerant level. If the Refrigerant level is low technician should follow published Service Information diagnostics. If the Refrigerant level is over 500 grams technician will use Global Diagnostic System 2 to verify if the Remote Heater and Air Conditioning Module is up to date and update if n
PIP5081K
This Preliminary Information communication provides information to the technician about vehicles that may have whistle, scrape or whine type noise while driving that may be more noticeable during regenerative braking. Technician may find this noise emanating from the left side of the drive unit. The tech may also state that the vehicle has a current or history diagnostic trouble code P0A46. The noise may be caused by the drive motor rotor bearing cage separated. Technician should replace the bearing with the new updated part number.
PIC6292A
This Preliminary information communicates that aPropulsion Power is reduced message occurs during regular operation, and there are no DTCs present, then contact GM Technical Assistance for direction
070849020M
IPC Odometer Programming Method Quick Reference Guide
150089004B
Information Regarding the Differences Between Fluid Leakage and Seepage This bulletin is intended to help identify the differences between what is considered a fluid leak and what is considered seepage. Improper diagnosis may lead to unnecessary component replacement. Use the following information to determine if the condition is normal acceptable seepage or a defective component
150089005A
Essential Tools that Include Consumable Parts (U.S. Only)
17-NA-319
Diagnostic Tips for Loss Of Brakes, Brake Pedal Going To Floor, Brake Pedal Hard, Brake Pedal Mushy, Possible Service Brake Assist and/or Service Stabilitrak Lights Illuminated Condition Some customers may comment on the brake pedal going to the floor, brake pedal hard, brake pedal mushy, or possible Service Brake Assist and/or Service Stabilitrak lights illuminated
PIC6292
This Preliminary information communicates that aPropulsion Power is reduced message occurs during regular operation, and there are no DTCs present, then contact GM Technical Assistance for direction
PIC5920G
This Preliminary Information communication provides information to the technician about vehicles that will not charge and Service Engine Soon Malfunction Indicator Lamp on. Technician may find Diagnostic Trouble Codes P0AA6 and/ or a P1F0E set on 2011-2013 Volt or a P0DAA on 2014 Volt or Cadillac ELR in the Hybrid Powertrain Control Module 2.
PIC5856E
This Preliminary Information communication provides information to the technician about vehicles that may have a Service Engine Soon Malfunction Indicator Lamp on. Technician may find a Diagnostic Trouble Codes P0C57, P0C58 and/or P0C62. When the technician has duplicated and is unable to find a repair after checking wiring and following normal diagnosis, please replace the Motor B Position Sensor to resolve the concern. Also insure that the Drive Motor Generator Control Module has the latest calibration.
PIP5081J
This Preliminary Information communication provides information to the technician about vehicles that may have whistle, scrape or whine type noise while driving that may be more noticeable during regenerative braking. Technician may find this noise emanating from the left side of the drive unit. The tech may also state that the vehicle has a current or history diagnostic trouble code P0A46. The noise may be caused by the drive motor rotor bearing cage separated. Technician should replace the bearing with the new updated part number.
PIC5920F
This Preliminary Information communication provides information to the technician about vehicles that will not charge and Service Engine Soon Malfunction Indicator Lamp on. Technician may find Diagnostic Trouble Codes P0AA6 and/ or a P1F0E set on 2011-2013 Volt or a P0DAA on 2014 Volt or Cadillac ELR in the Hybrid Powertrain Control Module 2.
PIC5414H
This Preliminary Information communication advises the technician what affects electric range and provides driving tips for better energy efficiency. Vehicles may have an electric range is less than customer expectations or what is being displayed on the in-vehicle display for EV range.
PIC5856D
This Preliminary Information communication provides information to the technician about vehicles that may have a Service Engine Soon Malfunction Indicator Lamp on. Technician may find a Diagnostic Trouble Codes P0C57, P0C58 and/or P0C62. When the technician has duplicated and is unable to find a repair after checking wiring and following normal diagnosis, please replace the Motor B Position Sensor to resolve the concern. Also insure that the Drive Motor Generator Control Module has the latest calibration.
GCUS-3-848
44180 02 - Customer Satisfaction. Certain vehicles may have key codes which were inappropriately handled by a third party which could increase the risk of vehicle theft. Dealers are to replace all applicable keys and lock cylinders with new key configurations.
PIP5246A
This Preliminary Information communication provides information to the technician the steps to diagnose and repair vehicles that have Check Engine Light illuminated with an "Engine Unavailable" and “Reduced Propulsion” messages on the Driver Information Center. Technician will find Diagnostic Trouble Code P1B03. Technician should replace Motor 1 Stator.
PIP5463
This Preliminary Information communication provides information to the technician about vehicles that have a Malfunction Indicator Lamp on and may have a loss of propulsion. Technician may find Diagnostic Trouble Code P0604 set in the Hybrid Powertrain Control Module Technician will need to replace the (T6) Power Inverter Module.
16NA241
THIS TECHNICAL BULLETIN PROVIDES A PROCEDURE TO CHECK THE CYLINDERS FOR DAMAGED PISTONS AND DETERMINE IF THE USE OF AFTERMARKET CALIBRATIONS OR PERFORMANCE PARTS MAY BE THE CAUSE.
PIT5074J
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT THE USE OF J-35616-64B TERMINAL TEST PROBE, REPLACEMENT TERMINALS, AND TERMINATED LEADS. THE J-35616-64B IS THE LATEST TEST PROBE RELEASED FOR CHECKING TENSION OR PROBING THE .64 SERIES TERMINALS. THE TEST PROBE TERMINAL HAS BEEN RELEASED IN THE TERMINAL REPAIR KIT (J-38125-620H) LOCATED IN LEAR TRAY 7 PART NUMBER 963716-2. THERE ARE 5 TERMINATED LEADS IN A PACKAGE PART NUMBER IS 13505346, WHICH CAN BE ORDERED THROUGH YOUR NORMAL GENERAL MOTORS CUSTOMER CARE AND AFTERSALES PARTS CHANNEL
PI1394A
THIS INFORMATIONAL BULLETIN PROVIDES ADDITIONAL INFORMATION ON HOW TO INSTALL PISTONS AND SUGGEST WHAT TOOLS TO USE.
PI0388F
THIS PRELIMINARY INFORMATIONAL BULLETIN PROVIDES A PROCEDURE TO REPOSITION THE FRONT SEAT BELT LATCH PLATE FOR CONCERNS REGARDING THE SEAT BELT WEBBING OR LATCH PLATE COMING TWISTED.
PIP4786C
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT VEHICLES THAT MAY HAVE LOW OIL PRESSURE MESSAGE. TECHNICIAN MAY ALSO FIND A DIAGNOSTIC TROUBLE CODE P0521 IN THE ENGINE CONTROL MODULE. TECHNICIAN SHOULD FOLLOW ALL PUBLISHED SERVICE INFORMATION DIAGNOSIS. WHEN USING A SCAN TOOL IF THE OIL PRESSURE IS LOW BUT THE OIL PRESSURE AT THE OIL FILTER HOUSING IS CORRECT, TECHNICIAN SHOULD INSPECT THE VALVE LIFTER OIL FILTER FOR DEBRIS/SLUDGE THAT COULD BE RESTRICTING OIL FLOW TO THE OIL PRESSURE SENSOR. TECHNICIAN SHOULD REMOVE THE VALVE LIFTER OIL FILTER AND CLEAN IT. IF THE VALVE LIFTER OIL FILTER CANNOT BE CLEANED REPLACE IT.
030603004R
THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION ON HOW TO TEST A BATTERY AND WHAT IS NEEDED TO WARRANTY A BATTERY.
140089004B
THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION FOR IGNITION KEY, FOB, KEY TAGS AND KEY RINGS CONFIGURATION FOR VARIOUS VEHICLES AND APPLYING A QR CODE STICKER OR BARCODE STICKER TO THE FOB.
16NA249
THIS INFORMATIONAL BULLETIN EXPLAINS A POSSIBLE NORMAL WHINING NOISE FROM THE BALANCE SHAFT CHAIN IF THE VEHICLE HAS LESS THAN 10,000 MILES ON IT.
070898001B
THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION ON GM DOES NOT APPROVE THE USE OF CLIPPING TO REPAIR COLLISION DAMAGE TO VEHICLES. GM HAS NOT TESTED OR VALIDATED A CLIPPED VEHICLE REPAIR; THEREFORE, GM CANNOT ENDORSE THIS TYPE OF REPAIR OR CONFIRM THE CRASH PERFORMANCE DURING A SUBSEQUENT COLLISION.
000601012F
THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION TO GM DEALERS ON THE CORRECT CLEANING METHODS WHEN CLEANING ENGINE GASKET SEALING SURFACES.
030604017I
THIS INFORMATIONAL BULLETIN EXPLAINS THE USE OF DIESEL FUEL ADDITIVES IN AN ENGINE, ARE NOT REQUIRED UNLESS THE CUSTOMER DESIRES ADDITIVES TO PREVENT FUEL CONCERNS DEPENDING ON FUEL OR TEMPERATURE RELATED CONDITIONS.
110849001S
THIS TECHNICAL BULLETIN PROVIDES A PROCEDURE TO REMOVE THE TRANSPORT MODE ON MESSAGE DISPLAYED IN THE DIC DUE TO VEHICLES SHIPPED OVER LONG DISTANCES OUTSIDE THE U.S. AND CANADA.
PIC6198A
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ON STEPS TO PERFORM TO DETERMINE IF THE CUSTOMER'S BATTERY DRAIN CONCERN IS BEING CAUSED BY A KNOWN CONCERN WITH BLUETOOTH CALL TRANSFER OPERATION WHEN EXITING THE VEHICLE. IF THE CONCERN IS DUPLICATED AT THE DEALER WITH THE ONSTAR LED IS STILL GREEN AFTER THE VEHICLE IS TURNED OFF AND THE BLUETOOTH CALL WAS DISCONNECTED. DEALER SHOULD ADVISES THAT ENGINEERING IS AWARE OF THE CONCERN AND IS CURRENTLY INVESTIGATING THE ISSUE.
000601026I
THIS INFORMATIONAL BULLETINS PROVIDES INFORMATION ON THE INTAKE MANIFOLD INSPECTION/REPLACEMENT AFTER SERVERE INTERNAL ENGINE DAMAGE.
16-NA-222
THIS INFORMATIONAL BULLETIN PROVIDES THE TECHNICIAN WITH WHAT MAY HAPPEN TO AN ENGINE DUE TO LACK OF MAINTENANCE.
PIP5094A
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THAT ,WHEN TESTING ANY CIRCUIT FOR OPEN OR RESISTANCE, IT IS IMPERATIVE THAT ALL RELATED TERMINAL PIN FIT AND TENSION BE CHECKED WHEN THE TEST STEPS REQUIRE DISCONNECTION OF THE CONNECTOR OR COMPONENT, PRIOR TO ANY COMPONENT REPLACEMENT. ALWAYS USE THE RECOMMENDED TERMINAL TEST TOOL DURING THESE TESTS.
SB-02-07-30-029Z
THIS INFORMATIONAL BULLETIN PROVIDE INFORMATION ON THE PRODUCT QUALITY CENTER (PQC) ASSEMBLY REPLACEMENT PROCESS.
PIC-5374-D
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ON THE STEPS TO DIAGNOSE AND REPAIR THE CONCERN OF RECEIVING FREQUENT "OFF ROUTE" MESSAGES WHILE FOLLOWING TURN BY TURN (TBT) ROUTE NAVIGATION. THE TECHNICIAN IS PROVIDED INSTRUCTIONS FOR RESETTING THE VEHICLE COMMUNICATION INTERFACE MODULE FOR THIS CONCERN.
PIC5374D
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ON THE STEPS TO DIAGNOSE AND REPAIR THE CONCERN OF RECEIVING FREQUENT "OFF ROUTE" MESSAGES WHILE FOLLOWING TURN BY TURN (TBT) ROUTE NAVIGATION. THE TECHNICIAN IS PROVIDED INSTRUCTIONS FOR RESETTING THE VEHICLE COMMUNICATION INTERFACE MODULE FOR THIS CONCERN.
PIP5189B
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ON THE STEPS TO DIAGNOSE AND REPAIR THE CONCERN OF BLACK SMOKE WHEN STARTING THE VEHICLE AFTER SITTING.
PIC-6198
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ON THE STEPS TO DIAGNOSE AND REPAIR THE CONCERN OF A DEAD BATTERY AFTER LEAVING THE VEHICLE DURING A BLUETOOTH CALL.
PIC6198
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ON THE STEPS TO DIAGNOSE AND REPAIR THE CONCERN OF A DEAD BATTERY AFTER LEAVING THE VEHICLE DURING A BLUETOOTH CALL.
PIC6193A
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN TO CONTACT THE GM TECHNICAL ASSISTANCE CENTER FOR FURTHER INSTRUCTIONS. THE CONCERN IS THE RADIO MAY BE UNABLE TO SAVE XM FAVORITE STATIONS.
PIP5168E
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ON THE STEPS TO DIAGNOSE THE CONCERN, AND THE STEPS TO REPAIR THE CONCERN OF THE VEHICLE CRANKS BUT DOES NOT START. THE TECHNICIAN IS TO INSPECT FOR A SHEARED CAM PIN IN THE ENGINE.
PIC4707E
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN TO DIAGNOSE THE CONCERN AND THE STEPS TO REPAIR THE CONCERN. THE VEHICLE'S XM TRAVEL LINK MAY BE INOPERTIVE.
PIC5088F
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ON THE STEPS TO DIAGNOSE AND REPAIR THE CONCERN. THE VEHICLE'S XM RADIO ONLY HAS XM PREVEIW CHANNELS.
SB-10-08-46-001C
THIS TECHNICAL BULLETIN PROVIDES A PROCEDURE TO CONTACT ONSTAR FOR HARD MUTE REQUEST TO CORRECT A CUSTOMER CONCERN WHEN THE RADIO IS ON, IT DOES NOT MUTE ENOUGH WHEN THE ONSTAR® TURN-BY-TURN NAVIGATION DIRECTIONS ARE ANNOUNCED DUE TO CUSTOMER IMPROPERLY SETTING THE RADIO VOLUME HIGH ENOUGH WHEN THE TURN-BY-TURN NAVIGATION MESSAGES ARE PLAYED.
SB-15-06-03-001B
THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION THAT MAY BE USEFUL ON DIAGNOSING BATTERIES THAT HAVE SET FOR A LONG PERIOD OF TIME AND/OR SET IN COLD WEATHER CLIMATES AND TESTING THOSE BATTERIES.
PIC-4935-E
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO HELP THE DEALERSHIP TECHNICIANS PERFORM A PARASITIC DRAIN TEST FOR THE ONSTAR MODULE. WHEN PERFORMING BATTERY PARASITIC DRAIN TEST, THERE MAY BE SOME CONFUSION AS TO WHAT THE NORMAL POWER CONSUMPTION READING SHOULD BE FROM THE ONSTAR SYSTEM.
PIC4935E
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO HELP THE DEALERSHIP TECHNICIANS PERFORM A PARASITIC DRAIN TEST FOR THE ONSTAR MODULE. WHEN PERFORMING BATTERY PARASITIC DRAIN TEST, THERE MAY BE SOME CONFUSION AS TO WHAT THE NORMAL POWER CONSUMPTION READING SHOULD BE FROM THE ONSTAR SYSTEM.
PIT5389A
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ON THE STEPS FOR DIAGNOSING THE CONCERN. THE VEHICLE MAY BE UNABLE TO CONNECT TO ONSTAR USING THE WHITE, BLUE OR RED ONSTAR BUTTONS.
SB-03-06-03-004Q
THIS WARRANTY ADMINISTRATION BULLETIN PROVIDE POLICY INFORMATION ON USING THE EL-50313 MIDTRONICS GR8 BATTERY TESTER/CHARGER FOR DIAGNOSING BATTERY REPLACEMENTS AND MAINTAINING BATTERIES ON NEW VEHICLES IN DEALER INVENTORY.
SB-06-08-47-001L
THIS INFORMATIONAL BULLETIN PROVIDES WARRANTY INFORMATION ON USING THE SERVICE PROGRAMMING SYSTEM (SPS) FOR PROGRAMMING CONTROL MODULES
SB-07-06-01-016C
THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION INTERNAL ENGINE NOISE OR DAMAGE AFTER OIL FILTER REPLACEMENT
SB-16-NA-119
THIS WARRANTY ADMINISTRATION BULLETIN PROVIDES INFORMATION ON GMS POLICY ON PERFORMING GM COVERED VEHICLE SERVICES AND MAINTENANCE ON VEHICLES ORIGINATING/SOLD IN CANADA.
PI-0754-B
THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION ON A NORMAL CONDITION ON TEMPERED GLASS OF SPOTS SHOWING ON THE REAR AND SIDE WINDOWS WHEN THE VEHICLE IS IN THE SUNLIGHT.
SB-16-NA-117
THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION ON THE PURPOSE OF MAGNETIC DRAIN PLUGS.
PI-0281-E
THIS PRELIMINARY INFORMATIONAL BULLETIN PROVIDES INFORMATION THAT MAY BE HELPFUL WHEN ADDRESSING UNDERBODY COMPONENT CORROSION WITH CUSTOMERS.
PIC-5260-A
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THE STEPS ON DIAGNOSING THE CONCERN. VEHICLE'S SUNROOF OPERATION INTERMITTENT, BIND, NOISE, AUTO-REVERSE, AND/OR WATER LEAKS.
PIC5260A
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THE STEPS ON DIAGNOSING THE CONCERN. VEHICLE'S SUNROOF OPERATION INTERMITTENT, BIND, NOISE, AUTO-REVERSE, AND/OR WATER LEAKS.
SB-03-07-29-004K
THIS INFORMATIONAL BULLETIN PROVIDE INFORMATION ON THE OPERATING CHARACTERISTICS OF A MANUAL TRANSMISSION.
06-00-89-031D
OEM and Remanufactured Engine and Automatic Transmission/Transaxle Identification
PIP4880F
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
PIP4880E
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
PIC5920D
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
PIC5920B
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
PIC5920C
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
PIC5959A
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
99-08-51-007F
Refinishing Aluminum Wheels This bulletin updates General Motor's position on refinishing aluminum wheels. GM does not endorse any repairs that involve welding, bending, straightening o re-machining. Only cosmetic refinishing of the wheel's coatings, using recommended procedures, is allowed. Evaluating Damage In evaluating damage, it is the GM Dealer's responsibility to inspect the wheel for corrosion, scrapes, gouges, etc. The Dealer must insure that such damage is not deeper than what can be sanded or polished off. The wheel must be inspected for cracks. If cracks are found, discard the wheel. Any wheels with bent rim flanges must not be repaired or refinished. Wheels that have been refinished by an outside company must be returned to the same vehicle. The Dealer must record the wheel ID stamp or the cast date on the wheel in order to assure this requirement. Refer to Refinisher's Responsibility Outside Company later in this bulletin.
PIC5381B
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
PI0281D
Underbody Component Corrosion The following information may be helpful when addressing underbody component corrosion with customers. Some customers may comment that one or more of their vehicle's underbody components are showing some form of corrosion. This corrosion may be red in appearance (rust) if the component is steel, forged iron or cast iron. This corrosion may also be grey or white in color if the component is constructed of an aluminum alloy.
PIP4891F
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
PIC5920A
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
PIC5903A
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
PIC5920
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
PIC5921
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
PIP4870B
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
PIP4880D
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
PIC5414C
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
PIP4859C
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
PIP4869C
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
PIP5000B
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
Complaint counts are reports filed with NHTSA, not failure rates. A common model collects more of them than a rare one that breaks more often.