Vehicle report
Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
P001
KW: The chassis list has been updated to include 1 chassis. The total chassis count is now 53. A link to the PACCAR Powertrain Prognostics Webcast has been added in the Links section. PB: The chassis list has been updated to include 8 chassis. The total chassis count is now 130. A link to the PACCAR Powertrain Prognostics Webcast has been added in the Links section.
P002
KW: A link to the PACCAR Powertrain Prognostics Webcast has been added in the Links section. PB: The chassis list has been updated to include 2 chassis. The total chassis count is now 4. A link to the PACCAR Powertrain Prognostics Webcast has been added in the Links section.
43-089
This optional software update is expected to be available after 08/28/2026.
24KWC/24PBC
Updated Sheppard Steering Gear Classification Tool link in Inspection Procedure
24KWL/PBL
The verbiage in the Introduction section has been updated.
43-088
The procedure has been updated to include additional steps for verifying the software level on the vehicle electronic control unit (VECU2) and digital display (DD). Steps have also been added to the PACCAR Common Rail Injection 2 (PCI2) software verification.
46-029
When DAVIE version 26.21.2 is used to update the VECU3 to software version 3.4.46.0, the VECU3 5071 component group may display as --- after programming.
14-037
An improved transmission bracket is now available for replacement on certain chassis equipped with a PACCAR TX-12 transmission, featuring a more durable design for enhanced long-term performance.
41-029
Incorrect air filters may be inadvertently installed in certain chassis equipped with under-hood Donaldson air filter housings.
E318
The Condition, Chassis Affected, Service Action, Warranty, and Procedure sections have been updated to include the latest prognostics bulletin verbiage. The Warranty section has also been updated to include Peterbilt specific SRT codes for filing cross-division repairs.
T024
KW & PB: New software is available for download. The DAVIE4 cache must be cleared before attempting to reprogram a chassis that is experiencing problems to ensure the latest version of software is installed. Follow all steps in the attached procedures before submitting a TCS case.
46-027
The currently published HD BEV Chassis with PACCAR EPowertrain Service (Built After 1/14/2026) de-energizing Procedures on ServiceNet cannot be utilized for certain pre-production Battery Electric Vehicle (BEV) chassis.
T-024
The repair procedure has been updated to include diagnostic steps.
27-012
The attachment for Eaton bulletin TAIB-1015 has been updated to the latest version to improve process flow.
43-080
KW: A new recommended repair has been added to verify the software level and close the campaign in SIR.The repair procedure has been updated with additional note boxes for clear instructions. PB: The repair procedure has been updated with additional note boxes for clear instructions.
R2601
Updated primary and/or secondary chassis modules for certain pre-production Kenworth chassis are now available for installation.
99-051
There is an update to the CARB Base Emissions Warranty Limits table and Manufacturer’s Warranty Coverage section in certain Engine Model Year (EMY) 2025 MX-11 and MX-13 Operator’s Manuals.
02-177
Troubleshooting procedures for 2.1m cab power windows are now available.
43-087
(KW) Certain T680 / T800 / T880 / W900 / W990 have updated GHG labels available for order and installation.
02-201
This recently published bulletin has been updated to include inspection procedures to assess if a hood is repairable.
41-024
Procedures have been updated to include additional truck models in the service intervals table.
E338
Certain EPA21 PACCAR MX engines are equipped with PHINIA fuel injectors that do not meet PHINIA’s manufacturing specifications.
45-070
The attached procedures document has been updated with more detail and explanations. This is not a stand-alone procedure. Cummins Quickserve troubleshooting will specify the use of these procedures while troubleshooting specific fault codes.
14-034
Bogie Crossmember Torque Value Update - Procedure has been updated to correct torque values.
E326
EPA17-24 MX Fuel Injector Connector - This bulletin has been revised to include all EPA17-24 and CARB24 PACCAR MX engines.
24KWF/PBF
Sheppard Recall Update March 2026 - The Parts section has been updated with revised steps for opening a TCS365 Order Support – Order Inquiry case.
37-004
PACCAR MX-13 VECU3 Software Update - Certain heavy-duty chassis equipped with a PACCAR MX-13 engine are eligible for a Vehicle Electronic Control Unit (VECU3) software update.
43-083
Exhaust Stack Isolators - Early wear of the polyurethane exhaust stack isolators may occur on certain Kenworth chassis due to excessive heat. Early wear of the polyurethane exhaust stack isolators may occur on certain Peterbilt chassis due to excessive heat.
14-036
One-Piece Aluminum Crossmember Repair - Repair procedures are available to support the replacement of intermediate or midship one-piece aluminum crossmembers.
25PACF
Parts and procedures are now available for all affected chassis equipped with Vehicle Electronic Control Unit (VECU) part number Q21-1157-013-011 / Q21-1157-013-013 / Q21-1157-002-002 / Q21-1157-004-004 / Q21-1157-006-006 / Q21-1157-009-009. See attached Parts Matrix for required parts per chassis.
25KWB/25PBB
A new Recommended Repair has been added. It must be used if safety recall 25PACF is performed prior to or at the same time as this repair since the 25PACF remedy also satisfies this safety recall.
R2405
All parts necessary to complete Phase 2 of this bulletin are now available. This retrofit provides certain chassis equipped with Cummins X15N (Natural Gas) engines with production level parts to replace preproduction parts installed at the time of manufacture.
25PBE
Parts and repair procedures are now available. Certain chassis may have a rear suspension tracking rod that interferes with the left rear brake valve components during full suspension travel. This interference could cause a loss of the rear service brake or ABS modulation for one rear axle wheel end, increasing the risk of a crash.
CE033
32 fuel injector part numbers (16 for MX-11 and 16 for MX-13) have been added to this warranty policy.
E323
A required spacer tool set is now available to streamline the injector replacement process. The spacer tool set allows certain fuel system components to be loosened instead of removed to provide access to the injectors. See Bulletin 98-031 for details. Tools are not reimbursable through this Bulletin.
R2306 - PB
All EMUX retrofit procedures updated to make it clear that the VECU3 must have software updated and vehicle mileage confirmed correct before updating the Digital Display. Parts and Procedure section also updated to include the Vehicle Emissions Control Information label ordering and installation instructions. This label is required for all chassis involved in R2306. Included additional reference to Cummins bulletin C7014 in the procedure section for ordering emissions labels.
R2405 - PB
Due to parts availability issues, this bulletin will be divided into 2 phases. Phase 1 will enable these chassis to be brought into emissions compliancebefore 06/30/2025 to avoid fi nes and penalties. Phase 2 will include all parts that are not currently available but are necessary to bring chassis up toproduction level. This bulletin will be updated once all Phase 2 parts become available . The emissions exemption for all chassis involved in this retrofi t expires on 06/30/2025. After that date, all chassis that have not received this Retrofi t willbe out of compliance with emissions regulations and illegal to operate . NOTE If emissions exemptions are allowed to expire, vehicle owners could receive civil fines per regulation 40 CFR 19.4 up to $5,911 per engine. In addition, owners may be required to discontinue operation of the vehicle until the retrofit is completed. Campaign start date: 04/18/25
43-080 PB
As of 03/25/2025, this campaign has resumed. Software updates are now available to complete this campaign.
25PBB
Safety Recall The Exterior Lighting Switch (ELS) in certain Model 535, 536, 537, 548, and 567 chassis may not function and can be reset only by a key cycle. This issue may result in non-compliance with FMVSS/CMVSS 101 and 108. Affected chassis must have the Vehicle Soft ware updated.
E327
Vehicles equipped with PACCAR MX engines with Engine Software Version NA202 or NA206 may display a dash STOP lamp incorrectly. PCI-2 software on these chassis must be reverted from NA202 to NA201 (Pack 2 injectors) or from NA206 to NA191 (Pack 1 injectors) to prevent incorrect STOP lamp display. 11014768 20250304 E327 20250227 E327 Emissions PETERBILT 520 2025 ENGINE Vehicles equipped with PACCAR MX engines with Engine Software Version NA202 or NA206 may display a dash STOP lamp incorrectly. PCI-2 software on these chassis must be reverted from NA202 to NA201 (Pack 2 injectors) or from NA206 to NA191 (Pack 1 injectors) to prevent incorrect STOP lamp display.
24PBK
Safety Recall Specific 2024 Peterbilt Model 367, 389, 548, and 2024-2025 520 and 567 chassis equipped with a PACCAR 20k Steer Axle have been identified as having steering arm and/or tie rod arm fasteners that may be improperly torqued and can be at risk of failing. If both fasteners in either steering arm or tie rod arm fail, there may be a loss of steering control, which could increase the risk of a crash. Affected chassis will have all steering arm and tie rod arm bolts removed, replaced with new bolts, and torqued properly.
E322 - PB
Campaign An MX-13 CARB Software update is available to improve reliability and uptime. The software must be updated to NA-110C before releasing any chassis to the final customer. Certain Vehicle Model Year 2025 567, 579, and 589 chassis equipped with Engine Model Year (EMY) 2024 CARB MX-13 engines and NA-100C software may experience a Malfunction Indicator Lamp (MIL) due to a software issue. Without this update, a derate may occur. Campaign start date is 01/15/2025.
24PBL
Safety Recall Updated software and procedures are now available. Certain Vehicle Model Year 2021-2025 Peterbilt chassis configured for trailer towing require a software update for the Bendix EC80 ABS ECU. Software update procedures for certain Battery-Electric Vehicles (BEV) and EC80 ABS ECU part numbers are not yet available. This bulletin will be updated when software update procedures are available for these chassis. Safety Recall publish date: 1/10/25
E319
Emissions Campaign Engine Model Year 2024 may not be displayed correctly on the PACCAR MX Engine Label. New and improved PACCAR MX Engine Labels are now available to be installed. Campaign start date is 11/26/2024
24PBH
Safety Recall Reference Cummins Safety Recall C7083 Cummins alerted Peterbilt to a defect which relates to motor vehicle safety that may affect certain Cummins X15 engines. Refer to Cummins Safety Recall C7083 for repair information.
E322
E322 - EMY2024 CARB MX Software Update - INTERIM Campaign – Interim Notification Certain model year 2025 567, 579 and 589 chassis equipped with EMY2024 CARB MX-13 engines and NA-100C software may experience a Malfunction Indicator Lamp (MIL) due to a software issue. If ignored, a derate may occur. This bulletin will be updated once the software is available.
E290
FIX-AS-FAIL Updated to include EPA2024 compliant engines. Fuel Filters must be changed before first cleaning. EPA2021 injector cleaning is referenced in RMI for certain injector faults. Complete the procedures in E290. Discard any previous versions of E290 procedures – always use the most current document from the link in the bulletin.
27-010
Fix As Fail Approximately 150 chassis built with an Allison 6th Gen 4500 series 6-speed transmission were assembled with the incorrect transmission harness. A procedure to re-pin transmission harness has been developed. Fix-as-Fail start date is 09/18/2024.
24KWGD/24PBGD
This bulletin contains secondary inspection procedures and part replacement procedures for tie-rods identified as SUSPECT under 24PBGB ONLY. Certain chassis that have completed 24PBGB inspection with “GOOD” results but have not filed warranty claims to close out the campaign in SIR will need to file a claim and close out 24PBGD. Secondary inspection and replacement procedures are now available through this bulletin for parts found to be SUSPECT in the 24PBGB Safety Recall. Customers will be advised NOT TO DRIVE TRUCKS until this remedy is completed.
24PBF
SAFETY RECALL Repair parts and procedures are now available. Certain Peterbilt vehicles from Model Year 2025 may contain steering gear(s) with sector shaft gear teeth that may prematurely wear, crack, or fracture and interfere with the steering gear mechanism. This may lead to steering gear binding, which may increase the risk of a crash.
24PBGD
This bulletin contains secondary inspection procedures and part replacement procedures for tie-rods identified as SUSPECT under 24PBGB ONLY. Certain chassis that have completed 24PBGB inspection with “GOOD” results but have not filed warranty claims to close out the campaign in SIR will need to file a claim and close out 24PBGD. Secondary inspection and replacement procedures are now available through this bulletin for parts found to be SUSPECT in the 24PBGB Safety Recall. Customers will be advised NOT TO DRIVE TRUCKS until this remedy is completed.
24KWGB/24PBGB
Safety Recall Certain model year 2025 Peterbilt 220, 536, 537, 548, 567, 579, and 589 chassis may have a tie-rod with a ball stud that does not meet hardness specification. The ball stud may fracture, leading to a loss of steering and reduced vehicle control, increasing the risk of a crash. Customers will be advised NOT TO DRIVE TRUCKS until the remedy is completed.
36-191
Information Only Vehicles equipped with Digital Vision System (DVS) Mirror Mounted Cameras, that do not have optional left-hand or right-hand blind spotters, may set false Diagnostic Trouble Codes (DTC) 522490-9 or 522491-9. These DTCs can be ignored if corresponding blind spotter is not equipped. The next Digital Vision System Mirrors (DVS-M) software update will correct these false DTCs.
E307
CARB Emission s Manufacturer Warranty term and/or kilometers conversion displayed in certain EMY 2022-2023 PX-7 or PX-9 OperatorâÂÂs Manuals are incorrect.
15-031
This Bulletin contains parts ordering and replacement procedures for Steering Gears identified as SUSPECT under 24PBC ONLY. Steering Gears repaired under this bulletin MUST be entered into the Serial Number Tracking Form for 24PBC.
Complaint counts are reports filed with NHTSA, not failure rates. A common model collects more of them than a rare one that breaks more often.