Vehicle report

2018 POLARIS SLINGSHOT

Service bulletins

34 bulletins

Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.

Team Tip 2026-03

Service Campaign

Submitting a Debug Report immediately after a Digital Wrench II incident is strongly recommended. Digital Wrench II errors may be caused by vehicle module issues, software or equipment malfunctions, or interruptions during updates and flash procedures. Common causes include poor internet connectivity, low vehicle battery voltage, and accidental or premature disconnection of Digital Wrench II components.

SLG-6.18.2026

Other

This Ask Polaris article provides information to systematically identify the root cause of excessive exhaust smoke by distinguishing between oil consumption, coolant intrusion, and fuel-related conditions.

SLG-6.5.2026

Other

This Slingshot help center article provides information regarding battery maintenance on Model Year 2019 and older Slingshot vehicles.

SLG-6.1.2026

Other

This Ask Polaris article provides information about how to perform a leakdown test on Polaris Slingshot vehicles.

T-26-02-01

Other

A new input shaft seal, PN 3610429, has been released for Model Year 2015-2026 Slingshot right angle drives for improved leak resistance. Vehicles produced after 11/10/2025 have the updated seal. When installing, this seal requires a lower pinion rolling torque specification. Improper pinion rolling torque during service of the seal can lead to leaks, noise, and/or damage to the seal or right angle drive due to improper bearing load.

SLG-11-20-25

Other

This Slingshot help center article contains instructions for inspecting and adjusting your lights for model year 2019 and older Slingshot vehicles.

SLG-10.16.25

Other

This Slingshot help center article provides information regarding replacing the angle drive fluid on model year 2015-2019 Slingshot vehicles.

SLG-8.29.2025

Other

This Slingshot help center article provides information regarding spark plug inspection and replacement on model year 2015-2019 Polaris Slingshot vehicles.

SLG-04-15-2025

Other

This Slingshot Help Center article provides information regarding fuse replacement for Model Year 2019 and older Slingshot vehicles.

SLG-11.20.2024

Other

This Slingshot help center article provides information regarding adjustment and maintenance of the headlamps on Model Year 2019 and older Slingshot vehicles.

SLG-04.18.2023-2

Service Bulletin/Repair Instructions

This article provides information regarding battery maintenance on MY2019 and older Slingshot vehicles.

T-22-08-01

Service Bulletin/Repair Instructions

Slingshot has received a small number of post-repair contacts due to improperly installed rear axles, sprockets, and bearings. This Team Tip outlines the importance of all Loctite residue being removed from components as well as proper installation.

SLG-02.14.2022

Service Bulletin/Repair Instructions

Best practices for gauges, speedometers and tachometers regarding Slingshot vehicles. This version has been translated into French.

03SLG2021-12-07

Service Bulletin/Repair Instructions

Slingshot Ride Command Cell Modem

TDH-HOLD 4.29.21

Service Bulletin/Repair Instructions

STOP SALE on affected Slingshot units identified in your inventory until further notice.

02SLG2021-04-14

Service Bulletin/Repair Instructions

Customers come in with a key that was left off or a low battery event that caused their calculated DTE to be a random number. The quickest way to address this is the following: 1. Reset both Trip meters 2. Reset the AVG FUEL ECONOMY 3. Disconnect the battery for 20 minutes. 4. Reconnect and test ride vehicle for minimum 20 miles to get an average economy again.

SLG Winterizing

Service Bulletin/Repair Instructions

Winterizing tips for the Slingshot.

T-19-11-01

Service Bulletin/Repair Instructions

Due to a vendor change, the clutch master cylinder (PN 24249817) used on some 2015-2019 Slingshot S / SL / LE / SLR / GT models built on or before 01/18/2020 is no longer available and has been replaced with Kit 2208233.

TDT-19-01

Service Bulletin/Repair Instructions

Due to a vendor change, the clutch master cylinder (PN 24249817) used on the affected models listed above is no longer available and has been replaced with Kit 2208233.

T-18-11-01 R03

Service Bulletin/Repair Instructions

Polaris has introduced new software and map updates for the Ride Command Display. Dealers should encourage Slingshot owners using Ride Command to bring their units in to receive the software update. At this time, dealers should also verify the map version and update as necessary. The software update takes approximately 5 minutes to complete, while updating the map file may take up to 2 hours depending on PC configuration and internet speed.

T-18-11-01 R02

Service Bulletin/Repair Instructions

Polaris has introduced new software and map updates for the Ride Command Display. Dealers should encourage Slingshot owners using Ride Command to bring their units in to receive the software update. At this time, dealers should also verify the map version and update as necessary. The software update takes approximately 5 minutes to complete, while updating the map file may take up to 2 hours depending on PC configuration and internet speed. Ensure the staff is aware of and has practiced both update processes, so they can provide a positive customer experience.

T-18-11-01 R01

Service Bulletin/Repair Instructions

Polaris has introduced new software and map updates for the Ride Command Display. Dealers should encourage Slingshot owners using Ride Command to bring their units in to receive the software update. At this time, dealers should also verify the map version and update as necessary. The software update takes approximately 5 minutes to complete, while updating the map file may take up to 2 hours depending on PC configuration and internet speed. Ensure the staff is aware of and has practiced both update processes, so they can provide a positive customer experience.

T-18-10-01

Service Bulletin/Repair Instructions

This Team Tip is designed to bring awareness to updated information regarding hood alignment for all 2015-2019 Slingshot models. Updated information has been added to the Service Manual to provide dealers with clear direction on how to properly adjust hood latches, cable release timing and gap alignment using commercially available tools.

T-18-06-01

Service Bulletin/Repair Instructions

All 2017-2019 Slingshot models equipped with the Slingshade accessory (including factory-equipped GT models) present the possibility of contact between the driver’s seat headrest and the Slingshade door latch. With the Slingshade door closed, the seat headrest can make contact with the door latch while tilting the seat forward. If the seat is allowed to tilt forward unrestrained, the force of the seat can damage the door latch.

T-18-05-01

Service Bulletin/Repair Instructions

Slingshot vehicles utilize Absorbent Glass Mat (AGM) batteries which are selected for their superior vibration resistance, weight savings, and high output. This Team Tip is being released to provide the Slingshot dealer network with specific recommendations to help maintain and restore the AGM type batteries used in Slingshot vehicles.

TSA-18-01

Service Bulletin/Repair Instructions

Polaris has identified a quality issue affecting a small number of Slingshot mufflers, where insufficient penetration of muffler plug welds weakens the muffler wall, making it susceptible to fatigue failure. The first mode of failure is a loosening of the wall, distinguishable by a rattle during normal engine operation. If left unrepaired for an extended period of time, a hole may form in the muffler wall resulting in noticeably higher noise levels.

G-17-10-02

Service Bulletin/Repair Instructions

At Polaris, we are committed to the safety of our customers and riders. Through product design, dedicated safety engineering, and increased consumer awareness, Polaris continues to work toward a safe riding experience and proper operation of our products. The following information can be used to help identify and report Product Safety Concerns.

DW 3.9

Service Bulletin/Repair Instructions

Digital Wrench version 3.9 is now available for download. Updating to version 3.9 is required to update the base Digital Wrench software version from 3.8 to 3.9 to allow for future MY18 vehicle support.

T-17-05-01

Service Bulletin/Repair Instructions

Safety Bulletin T-16-06 has been updated to reflect an additional procedure. Polaris has determined that (PN 2207085-XXX) swingarm kits being shipped to dealers did not include two rubber grommets in the swingarm. If the rubber grommets were not included in the kit, remove the grommets from the original swingarm and install into the new swingarm as part of the procedure.

G-16-11-01

Service Bulletin/Repair Instructions

Polaris has released Team Tip G-16-10-01 to inform dealers that Polaris Mobile Digital Wrench (PMDW) version 3.28 or later requires dealers to enter a valid 10-digit Digital Wrench serial number to operate the app. The serial number requirement has been added to improve visibility to app downloads and usage.

SAF-16-01

Service Bulletin/Repair Instructions

A STOP RIDE MEANS THE CONSUMER MUST NOT OPERATE THEIR VEHICLE UNTIL THE REPAIR IS COMPLETE. We have been made aware that some dealers are incorrectly communicating the importance of STOP RIDE communications.

G-15-12-01 R03

Service Bulletin/Repair Instructions

There is no doubt that for a Polaris customer the process of picking up a brand new vehicle is one of the most exciting times in the ownership experience. To ensure that all Polaris dealers are equipped to deliver a world-class experience that matches the high quality and excitement of the products, PCDX was developed to create a mobile streamlined dealership delivery experience. PCDX combines the setup, registration, and delivery process into one easy to use application.

G-15-12-01 R02

Service Bulletin/Repair Instructions

PCDX is an online and mobile interface for providing a consistent dealer setup and customer delivery experience. The interface walks the dealer and the customer through a standardized online form that includes the PDI (pre-delivery inspection), general warnings, assembly and inspection, safety bulletins, test ride, customer information, customer walkaround and discussion, and customer acceptance. This application has been proven in dealerships to automate document retention, streamline vehicle setup, and provide a consistent, professional customer experience. Vehicles shipped after 11/1/2015 no longer include a paper PDI form with the vehicle setup material; instead dealers should complete the vehicle setup and PDI using the PCDX application, which can be located on the Dealer Website under Service and Warranty – PCDX.

G-15-12-01 R01

Service Bulletin/Repair Instructions

This Team Tip is being released to dealers to provide information regarding the required transition to online PCDX and PCDX training.

Reading this report

Complaint counts are reports filed with NHTSA, not failure rates. A common model collects more of them than a rare one that breaks more often.