IS-23019A
Service Bulletin/Repair Instructions
Sway bar collars improvement. Revision A : Add front sway bar support replacement and change bolts lenght.
Vehicle report
Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
IS-23019A
Sway bar collars improvement. Revision A : Add front sway bar support replacement and change bolts lenght.
IS-23019
SWAY BAR COLLARS IMPROVEMENT
IS-22106
H3 LAVATORY FAN RETROFIT KIT
MI22-12B
Air Tanks Draining Sequence. Revision: B - General Update
MI22-12A
Air Tanks Draining Sequence. Revision: A - Erroneous Secondary & Accessory tanks location.
MI22-12
Air Tanks Draining Sequence
IS20-925A
CENTRAL HVAC MERV FILTERS INSTALLATION
IS-20925A
CENTRAL HVAC MERV FILTERS INSTALLATION REVA
MI20-08C
STORAGE AND STARTUP GUIDELINES: Periodically, circumstances arise requiring operators to temporarily park a coach in storage. Whether it is a few weeks or several months, sporadic out of service times or a full stop, Prevost recommends following the guidelines in this document during times when: ⢠The coach can be operated on a regular/weekly basis while in storage. ⢠The coach will be in storage for an extended period without any operation. ⢠The coach will return to service following an extended period of downtime.
IS-18091A
TIE ROD 610052 FIRST INSTALLATION INSTRUCTIONS: Use these instructions when replacing the drop joint tie rod on S82, S84 / S84U I-beam axles. The new tie rod will be adjusted to the length of the original; however, a steering alignment needs to be performed after replacement.
MI20-19A
Rev A: Mention added concerning DDC Series 60 engine SCA requirement
MI20-19
INTRODUCING A NEW ENGINE COOLANT INTO SERVICE
MI02-17A
Revision : A Torque value reduced
IS-19165A
LAVATORY FAN RETROFIT KIT Applicable for H3 Series coaches from R-1012 (1994) Revision A: Added installation detail at step 8
SCi20-16
FAN CLUTCH PLATE BOLTS RE-TORQUING
IS-20923
H3 DRIVERâS PARTITION LITE INSTALLATION
MI20-08B
STORAGE AND STARTUP GUIDELINES Revision: B Parts added to Suggested Material 08-10-2020
MI20-12
JERKY, NOISY OR HARD TO TURN STEERING GEARBOX. HYDRAULIC END LIMITER ADJUSTMENT. All models â equipped with RB Bosch/ZF Servocom or Servocomtronic steering gearbox
MI20-08A
STORAGE AND STARTUP GUIDELINES: Rev A: 21516229 replaced by 23381562 20523393 replaced by 21454749 800383 removed 611471 replaced by 611360 70376808 replaced by 21036050 21396642 replaced by 20967831
MI20-09
PREVOST VEHICLE DISINFECTION PROCEDURE
MI20-08
STORAGE AND STARTUP GUIDELINES - ALL PREVOST VEHICLES & VOLVO 9700
MI15-24
Added: Power cables for L.H. side alternator & fan drive breaker box
IS-14076
This instruction sheets explains how to replace the fuel tank on H-series vehicles. (Replacing older series tanks by newer model)
IS-19923A
Revision : Addition of Wiring Schematics at the end of this document
IS-19923
This instruction sheet explains how to replace HVAC MODULE on certain vehicles;
IS-18091
This Instruction Sheet explains how to perform the first installation of Tie Rod 610052 on Prevost vehicles equipped with Dana S82, S84 / S84U I-beam axles, 1994- today
MI18-45A
Vehicles identified below are compatible with a new tie rod design. This new tie rod 610052 has updated ball joints and a fine adjuster sleeve. It replaces former drop type ball joint tie rods. Refer to IS-18091 for installation instructions. This document details maintenance inspection and toe-in adjustment with the new design tie rod.
IS-17910A
MESSAGE CENTER DISPLAY (MCD) REPLACEMENT
IS-12008
This Instruction Sheet explains how to repalce 062720 AND 063344 AC MODULES, that are obsolete and replaced by a new module and harness.
SCI09-28
PREVOST: INSTALLING THREE-POINT PASSENGER SEAT RESTRAINT SYSTEM. THE PURPOSE OF THE FOLLOWING PROCEDURE IS TO FACILITATE THE JOB AND TO HELP IDENTIFY THE DIFFICULT AREAS. ALSO INCLUDED MODELS HE-41 AND HE-45 COACHES MODEL YEARS 1998-2008; MODEL XLII AND X3-45 COACHES MODEL YEARS 1998-2008. *JS
MI08-04
FRONT AND TAG AXLE HUB BEARING AND KING PIN PERIODIC MAINTENANCE. BEARINGS MUST BE INSPECTED AT INTERVALS OF 30,000 MILES (48 000KM). KING PINS SHOULD BE SERVICED EVERY 6, 250 MILES (10,000 KM) OR TWICE A YEAR. ALSO INCLUDED MODEL VIP-45 MTH MODEL YEARS 2004-2008. MODEL XLII MTH MODEL YEARS 2004-2008. *JS
MI07-06
PREVOST: NEW FIXING HARDWARE FOR THE REAR HEIGHT CONTROL VALVE LINK ROD. THERE IS A POSSIBILTY THAT THE LINK ROD THAT CONNECTS THE HEIGHT CONTROL VALVE TO THE DRIVE AXELS SUPPORT FRAME COMES APART WHEN THE VEHICLE IS MOVING. MODEL VIP-45MTH MODEL YEAR 2004 ALSO INCLUDED. *JS
0410
INSPECTION & REPLACEMENT OF POWER STEERING PRESSURE HOSE. PREVOST. *TT
0416
MODIFICATION OF SPEED SENSOR CONNECTORS ON ALLISON WORLD TRANSMISSION. PREVOST. *TT
0407
INSPECTION OF CLUTCH ACTUATOR AIR LINE ON ZF-ASTRONIC TRANSMISSION. *TT
Complaint counts are reports filed with NHTSA, not failure rates. A common model collects more of them than a rare one that breaks more often.