Vehicle report
Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
MI26-00
The gasket thickness was increased from 1.5 mm to 3 mm to prevent interference between the collar ends, which previously made it impossible to reach the specified tightening torque. Increasing the gasket thickness ensures sufficient clearance between the collar ends and thus guarantees optimal tightening.
IS-23019A
Sway bar collars improvement. Revision A : Add front sway bar support replacement and change bolts lenght.
IS-23019
SWAY BAR COLLARS IMPROVEMENT
IS-22106
H3 LAVATORY FAN RETROFIT KIT
IS-18106
KIT POWER STEERING TANK CONVERTION CUMMINS TO ZF WITH D13 ENGINE
MI16-32
Improved bearings are now available to replace the original bearings used on some Prevost vehicles idler pulleys.
MI22-12B
Air Tanks Draining Sequence. Revision: B - General Update
MI22-12A
Air Tanks Draining Sequence. Revision: A - Erroneous Secondary & Accessory tanks location.
MI22-12
Air Tanks Draining Sequence
IS-22902
TAG AXLE HUB FLANGE - ALTERNATE CAP SCREW
MI20-08C
STORAGE AND STARTUP GUIDELINES : part number updates
IS21-072A
STEERING GATEWAY Revision A Cancel watch dog removal from EFD part of the instruction
IS20-925A
CENTRAL HVAC MERV FILTERS INSTALLATION
IS20-932A
H3 SERIES ENVIROCARE - IONS AIR SANITIZER
MI18-16B
BOSCH HD10 ALTERNATOR DIAGNOSTIC GUIDE Revision B To avoid replacement of alternators that are in fact in good working order, perform the steps which follow to help you perform a more precise diagnosis.
MI21-06
Diesel Exhaust Fluid ( DEF ) Contamination In Fuel System, Inspection And Repair â From US10 to newer engine generation
is_20089
LAVATORY COMPARTMENT SLIDING DOOR LATCH IMPROVEMENT
Mi21-07A
RONT & TAG AXLE â UNITIZED HUB BEARING END PLAY VERIFICATION AND REPLACEMENT
IS-08080B
Sound Selector replacement, VSS04 to VSS05; When replacing a vehicle sound selector model VSS04 with a new sound selector model VSS05, an interface harness is required to connect the vehicle harness to the new sound selector model and a new VSS05 compatible radio unit must also be installed. This procedure describes the steps required to perform this update.
IS-20932A
H3 SERIES ENVIROCARE - IONS AIR SANITIZER REV A
IS-20925A
CENTRAL HVAC MERV FILTERS INSTALLATION REVA
IS-20932
H3 SERIES ENVIROCARE - IONS AIR SANITIZER
IS-18091A
TIE ROD 610052 FIRST INSTALLATION INSTRUCTIONS: Use these instructions when replacing the drop joint tie rod on S82, S84 / S84U I-beam axles. The new tie rod will be adjusted to the length of the original; however, a steering alignment needs to be performed after replacement.
MI20-19B
INTRODUCING A NEW ENGINE COOLANT INTO PREVOST SERVICE CENTER NETWORK
MI20-19A
Rev A: Mention added concerning DDC Series 60 engine SCA requirement
MI20-19
INTRODUCING A NEW ENGINE COOLANT INTO SERVICE
MI02-17A
Revision : A Torque value reduced
IS-19165A
LAVATORY FAN RETROFIT KIT Applicable for H3 Series coaches from R-1012 (1994) Revision A: Added installation detail at step 8
SCi20-16
FAN CLUTCH PLATE BOLTS RE-TORQUING
IS-20923
H3 DRIVERâS PARTITION LITE INSTALLATION
MI20-08B
STORAGE AND STARTUP GUIDELINES Revision: B Parts added to Suggested Material 08-10-2020
MI20-12
JERKY, NOISY OR HARD TO TURN STEERING GEARBOX. HYDRAULIC END LIMITER ADJUSTMENT. All models â equipped with RB Bosch/ZF Servocom or Servocomtronic steering gearbox
IS-19910H
ELECTRIC FAN DRIVE COOLING SYSTEM CONVERSION WITH DELCO REMY ALTERNATOR Revision H: Parts obsolete: 050303, 391028, 562112 Replaced by: 830165 24V RED TELLTALE LIGHT MODULE QTY: 1x 381594 BRACKET, TELLTALE QTY:1x 561540 TAB TERMINAL, ST,16-14,1/4 INS QTY: 2x New holes drilled for cooling pack relocation
MI20-08A
STORAGE AND STARTUP GUIDELINES: Rev A: 21516229 replaced by 23381562 20523393 replaced by 21454749 800383 removed 611471 replaced by 611360 70376808 replaced by 21036050 21396642 replaced by 20967831
IS-20906
Plexiglass Shield Behind Driver H3 Series
MI20-09
PREVOST VEHICLE DISINFECTION PROCEDURE
MI20-08
STORAGE AND STARTUP GUIDELINES - ALL PREVOST VEHICLES & VOLVO 9700
MI15-24
Added: Power cables for L.H. side alternator & fan drive breaker box
IS-14076
This instruction sheets explains how to replace the fuel tank on H-series vehicles. (Replacing older series tanks by newer model)
IS-19910E
This Instruction sheet explains how to perform an Electric Fan Drive Cooling System Conversion with Delco Remy Alternator - H3 Series US10 To GHG17 Included
IS-17151
THIS INSTRUCTION SHEET EXPLAINS HOW TO REPLACE HALOGEN FOG LIGHT TO LED'S
IS-19043
THIS INSTRUCTION SHEET EXPLAINS HOW TO RELOCATE THE WHEEL CHAIR LIFT PARCEL RACK FAN
IS-18091
This Instruction Sheet explains how to perform the first installation of Tie Rod 610052 on Prevost vehicles equipped with Dana S82, S84 / S84U I-beam axles, 1994- today
IS-19910D
This Instruction sheet explains how to perform an Electric Fan Drive Cooling System Conversion with Delco Remy Alternator - H3 Series US10 To GHG17 Included
IS-19900D
ELECTRIC FAN DRIVE COOLING SYSTEM CONVERSION WITH BOSCH ALTERNATOR - H3 SERIES US10 COOLING SYSTEM
IS-19910C
ELECTRIC FAN DRIVE COOLING SYSTEM CONVERSION WITH DELCO REMY ALTERNATOR - H3 SERIES US10 up to GHG17
MI18-45A
Vehicles identified below are compatible with a new tie rod design. This new tie rod 610052 has updated ball joints and a fine adjuster sleeve. It replaces former drop type ball joint tie rods. Refer to IS-18091 for installation instructions. This document details maintenance inspection and toe-in adjustment with the new design tie rod.
IS-17910A
MESSAGE CENTER DISPLAY (MCD) REPLACEMENT
IS-18115
This instruction sheet explains how to install a GM Glove box Lock on H-Series vehicles
IS-17905A
This instruction sheet explains how to install an ELD interface kit on Pre-OBD Prevost Vehicles equipped with Volvo D13 Engines
IS-11003G
This Instruction sheet explains how to replace the ?MASTER ID? WITH ?MCM? Module
IS-13009D
This instruction sheet explains how to install and adjust drag link # 660699
IS-11003F
This Instruction sheet explains how to replace the "MASTER ID WITH MCM" Module
SCI18-46
This Service Center Instructions explains how to install the Prevost Ultimate Entertainment System
IS-13009C
This instruction sheet explains how to install and adjust drag link # 660699
IS-18905
This instruction sheet explains how to install hatches with fan on H3 vehicles.
IS-17910
This instruction sheet explains how to replace the message center display (MCD)
IS-15003E
This insruction Sheet explains how to insall the Bosch HD10 24v-150a Alternator Conversion Kit ? Twin Bosch Mounted On Volvo D13 Engine
MI16-17G
This Maintenance Information explains how to remove and install the Bosch HD10 (120A or 150A) alternators
MI16-08B
This Maintenance Information presentes the new method of locking the electromagnetic clutch in the event of a failure. These new electromagnetic clutches will feature locking tabs in replacement of the locking bolts.
MI18-16A
This Maintenance Information presents guidelines to help with the diagnosis of the Bosch HD10 alternators
MI16-17F
This Maintenance Information explains how to remove and install the Bosch HD10 (120A or 150A) alternators
IS-17905
This instruction sheet explains how to install an ELD interface kit on Pre-OBD Prevost Vehicles equipped with Volvo D13 Engines
IS-13009B
This instruction sheet explains how to install and adjust drag link # 660699
SCI17-35
This internal instruction explains how to bench program the FMS gateway module used in the ELD (Electronic Logging Device) interface kit for pre-OBD13 vehicles.
MI17-22
This Maintenance Information explains how to inspect the Fuel Tank Cradle Mounting Screws on a yearly basis
IS-17907
This instruction sheet explains how to install the Volvo Electronic Logging Device (ELD)
CK17-19A
This conversion kit explains how to remove TGW1 from vehicles using Tech Tool, no manual VDA changes needed. This conversion kit will work for any vehicle equipped with TGW1 up to the VIN's listed on the bulletin.
IS-11003E
This Instruction sheet explains how to remplace MASTER ID? WITH ?MCM? Module
IS-17901
This instructions sheet explains how to program a Wabco Smart Trac ABS ECU.
IS-15003D
This insruction Sheet explains how to insall the Bosch HD10 24v-150a Alternator Conversion Kit ? Twin Bosch Mounted On Volvo D13 Engine
IS-16100
This instruction sheet explains how to install latest radio models
IS-15003C
This instruction sheet explains how to use the Bosch HD10 24V-150A Alternator Conversion Kit
IS-17900
This Instruction Sheet explains how to install a wheel fender stainless steel protector
MI16-17E
This Maintenance Information explains how to remove and install the Bosch HD10 (120A or 150A) alternator.
MI16-08
On receiving your Kit Masters fan clutch you may notice a new method of locking the electromagnetic clutch in the event of a failure. These new electromagnetic clutches will feature locking tabs in replacement of the locking bolts. Applies to part number 550965; 550966 &550974.
IS-15003B
This instruction sheet explains how to use the Bosch HD10 24V-150A Alternator Conversion Kit
IS-08080A
WHEN REPLACING A VEHICLE SOUND SELECTOR MODEL VSS04 WITH A NEW SOUND SELECTOR MODEL VSS05, AN INTERFACE HARNESS IS REQUIRED TO CONNECT THE VEHICLE HARNESS TO THE NEW SOUND SELECTOR MODEL AND A NEW VSS05 COMPATIBLE RADIO UNIT MUST ALSO BE INSTALLED. THIS PROCEDURE DESCRIBES THE STEPS REQUIRED TO PERFORM THIS UPDATE.
MI16-15B
The Beru sensors used on Prevost vehicles to monitor tire pressure (TPMS system) are being replaced by new Huf sensors and their corresponding stainless valves stems. Since the older and newer sensors are using different valve stems, replacement of a defective sensor on older vehicles will require the use of a new kit number (valve stem and sensor assembly). The table below provides a quick overview between the older and newer part numbers depending on wheel application.
IS-11003D
This Instruction sheet explains how to remplace MASTER ID? WITH ?MCM? MODULE
MI16-22
Use this maintenance information procedure to resolve an undesired behaviour on 2008-2012 vehicles. In sleep mode, certain marker lights may remain illuminated.
MI16-15A
The Beru sensors used on Prevost vehicles to monitor tire pressure (TPMS system) are being replaced by new Huf sensors and their corresponding stainless valves stems. Since the older and newer sensors are using different valve stems, replacement of a defective sensor on older vehicles will require the use of a new kit number (valve stem and sensor assembly). The table below provides a quick overview between the older and newer part numbers depending on wheel application.
IS-14085
This Instruction sheet explains how to prevent AC Copper Pipes Chaffing at Engine Bulkhead
MI12-04C
This Maintneance informations presents an improved harness and wiring modification procedure to avoid certain fault codes and messages.
Mi16-15
The Beru sensors used on Prevost vehicles to monitor tire pressure (TPMS system) are being replaced by new Huf sensors and their corresponding stainless valves stems. Since the older and newer sensors are using different valve stems, replacement of a defective sensor on older vehicles will require the use of a new kit number (valve stem and sensor assembly). The table below provides a quick overview between the older and newer part numbers depending on wheel application.
MI16-16
This procedure explains how to perform a STARTER REMOVAL AND INSTALLATION, and does apply to Melco 105P70 starter part number #21212425.
MI15-51
This Maintenance Information explains how to run a n Air Conditionning performance test
MI15-61
This Maintrenance infomration explains that the Castrol Syntrans oil isn?t fully approved for 500 000 miles (800 000 km) extended drain intervals on the Volvo I-Shift transmission. For this reason, this oil has been downgraded to regular drain intervals. Find below, a list of Volvo?s approved oils for extended drain as well as regular drain intervals.
IS-11003A
This Instruction sheet explains how to replace MASTER ID? WITH ?MCM? MODULE
MI15-18
This Maintenance Information does explain how five year old vehicles and older should be subjected to a thorough structural inspection.
IS-15003A
This instruction sheet explains how to use the Bosch HD10 24V-150A Altenrator Conversion Kit
MI15-02
This Maintenance Information presents an improved differential breather kit, identical to the one now used in production. This new breather incorporates a "J" shaped hose that prevents oil leakage and water ingestion while allowing the axle to vent.
WB14-47B
On the vehicles affected by this bulletin, perform a software update of ECM (Engine Control Module) and ACM (Aftertreatment Control Module) to provide improved temperature-related behaviour. The software will also change urea dosing valve behavior at shutdown and key-on. As an additional improvement, replace the urea dosing valve by an improved design. These hardware and software improvements aim to reduce the occurrence of clogging and shorting of the Urea Dosing Valve.
MI1423
A new software version (v1.06) is available to update the CANtrak (Tire Pressure Monitoring System) module. This new version will allows a 10 min. delay before the ?SYSTEM ERROR NOT ALL TIRES MONITORED? message appears in the vehicle cluster when a tire pressure sensor loses its connection. NOTE: The new software version will only delays the cluster message, the CANtrak screen will still displays a ??? code for the corresponding pressure sensor.
IS-14900
This Instruction Sheet explains how to replace 562489 Dimmer, using kit #069136
WB13-60
On the vehicles affected by this bulletin, a software update for the Volvo I-Shift transmission is required. Software update has for effect to improve the gear change process to avoid clashing and wear on the split gear. This software update is necessary on all I-shift transmission up to but not including serial number 1100224372.
IS-08080
When replacing a vehicle sound selector model VSS04 with a new sound selector model VSS05, an interface harness is required to connect the vehicle harness to the new sound selector model and a new VSS05 compatible radio unit must also be installed. This procedure describes the steps required to perform this update.
MI13-33
This Maintenance Information explains that polyester reinforced silicone hoses and elbowscan be repalced by aramid reinforced hoses and elbows for improved long term durability, and that constant torque hose clamps for silicone hoses with 5/8po, 3/4po, 7/8po, 1 1/8po and 1 3/8po inside diameter (I.D) can be replaced by new WAVE SEAL type constant torque hose clamps.
MI13-06
This Maintenance Information explains that hose clamps with a smaller diameter are available to increase the adjustment range at the upper and lower radiator flexible connections and at the oil cooler connections located under the turbocharger.
WB12-41A
On the vehicles affected by this bulletin, an auxiliary coolant tank is available. This auxiliary coolant tank will prevent spillage due to expansion when main coolant surge tank is filled with too much coolant. *This warranty bulletin does not apply to vehicles equipped with the plastic surge tank
WB-12-41
PREVOST: WARRANTY INFORMATION PROVIDED REGARDING AVAILABILITY OF AN AUXILIARY COOLANT TANK, WHEN MAIN COOLANT SURGE TANK FILLED WITH TOO MUCH COOLANT AND AUXILIARY COOLANT TANK PREVENTS SPILLAGE DUE TO EXPANSION. MODEL 2010-2013 H3-41, H3-45 COACHES, H3 VIP MOTORHOMES. *PE UPDATED 3/26/13. *PE
WB12-31B
On the vehicles affected by this bulletin, a new and improved dipstick is available for installation.
IS11015B
This Instruction Sheet explains how to replace power relay p/n 561991 with improved power relay p/n 564218 and relay base p/n 564210
WB-12-31
PREVOST: INFORMATION BEING PROVIDED REGARDING THE REPLACEMENT OF DIPSTICK ON CERTAIN COACHES. MODELS 2009-2013 H3-45, H3-41, X3-45, XL11-45, X3-45. *PE
MI-12-11-A
PREVOST: INFORMATION BEING PROVIDED REGARDING THE MODIFICATION OF D13 US07 ENGINES' IMPROVED BELT TENSIONER TO PROLONG BELT LIFE. *PE
SP-12-01-A
PREVOST: INFORMATION IS BEING PROVIDED REGARDING TWO PROCEDURE METHODS OF PINNING OR REPLACING THE DOUBLE IDLER GEAR, ON CERTAIN VEHICLES ENGINE, THAT IS NECESSARY. *PE UPDATED 4/5/13. *PE
MI11-27
PREVOST: 12" BRUSHLESS CONDENSER FAN REPLACEMENT. MODELS INCLUDE XLII MTH, AND H3VIP MTH. MODEL YEARS ARE 2008-2011. *KB
WB11-05
PREVOST: EXHAUST PIPE ANGLE BRACKET INSPECTION. *KB
WB11-17A
PREVOST: JAMMED LATCH - RADIATOR DOOR AND DPF ACCESS DOOR. *KB
WB11-22
PREVOST: VOLVO D13 ENGINE HARNESS REPLACEMENT - OIL SEEPAGE AT UNIT INJECTOR PASS - THROUGH FITTING. *KB
SCI11-11
PREVOST: KIDDE FIRE EXTINGUISHER CONTROL HEAD REPLACEMENT. *KB UPDATED 5/9/2012. *KB
SP11-07A
PREVOST: ENGINE OIL COOLER - COOLANT DUCT COVER LEAKING INSPECTION/REPLACEMENT WITH EGR COOLER RETROFIT. *KB
SP11-12
PREVOST: VOLVO D13 ENGINE EPA2010 - RETIGHTENING OF CONICAL INJECTOR YOKE SCREW. *KB
WB11-02
PREVOST: REPLACING T1 BOSCH ALTERNATORS AND WATER PUMP BELT TENSIONERS. *KB
WB11-01A
PREVOST: VOLVO D13 ENGINE - AFTERTREATMENT HYDROCARBON INJECTOR (AHI) FUEL LINE FITTINGS - PROPER TIGHTENING VERIFICATION. *KB
WB10-36A
PREVOST: REPROGRAMMING OF I/O-A & I/O-B MODULES FOR IMPLEMENTATION OF THE ESSENTIAL FUNCTIONS TO OPERATE THE VEHICLE (BASIC LIMP-HOME FUNCTIONS). *KB
WB10-18
PREVOST: VOLVO D13 ENGINE OIL SEEPAGE AT UNIT INJECTOR HARNESS PASS-THROUGH FITTING. *KB
WB10-17
PREVOST: VOLVO D13 ENGINE - TURBOCHARGER SMART REMOTE ACTUATOR (SRA) FAULTS. *KB
WB10-01A
PREVOST: VOLVO D13 ENGINE: REPLACEMENT OF COPPER INJECTOR SLEEVE WITH CONICAL STAINLESS STEEL INJECTOR SLEEVE. *KB UPDATED 5/4/2012. *KB
WB10-26A
PREVOST: VOLVO D13 ENGINE CORRECTION OF THE DRV CONTROL VALVE AIR SUPPLY CIRCUIT. *KB UPDATED ON 5/9/2012. *KB
SCI10-02
PREVOST: INSTALLIN AN AIR DEFLECTOR IN ORDER TO REDUCE AMBIENT TEMPERATURE AROUND LINNIG RADIATOR FAN GEARBOX. *KB
WB09-13A
PREVOST: INSPECTING THE RADIATOR FAN DRIVE MECHANISM SUPPORT ON A DETROIT DIESEL ENGINE. ALSO INCLUDED MODEL VIP-45 BUS MODEL YEARS 2001-2010; MODEL XLII MTH BUS MODEL YEARS 2008-2009. *JS
WB09-26
PREVOST: ON VOLVO D13 ENGINES DASHBOARD 'CHECK ENGINE' WARNING LAMP COULD COME ON DUE TO CODE PID 171. ALSO INCLUDED MODEL MTH XLII-45E BUS SHELLS MODEL YEAR 2009. *JS
WB09-23
PREVOST: PREHEATER EXHAUST PIPE HOLDING CLAMP MAY NOT BE PROPERLY POSITIONED. MAKE SURE THAT THE HOLDING CLAMP IS LOCATED ABOVE THE SPLASH GUARD AND NOT BENEATH. *JS
WB09-25
PREVOST: ON VOLVO D13 ENGINES DASHBOARD 'CHECK ENGINE' WARNING LAMP COULD COME ON DUE TO CODE PID 110. ALSO INCLUDED MODEL MTH XLL45E BUS MODEL YEAR 2009 *JS
SCI09-05E
PREVOST: H3-41, H3-45 '2010 YEAR MODEL' FRONT PANEL RETROFIT. *JS
Complaint counts are reports filed with NHTSA, not failure rates. A common model collects more of them than a rare one that breaks more often.