Vehicle report
Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
MI26-00
The gasket thickness was increased from 1.5 mm to 3 mm to prevent interference between the collar ends, which previously made it impossible to reach the specified tightening torque. Increasing the gasket thickness ensures sufficient clearance between the collar ends and thus guarantees optimal tightening.
IS-23019A
Sway bar collars improvement. Revision A : Add front sway bar support replacement and change bolts lenght.
IS-23019
SWAY BAR COLLARS IMPROVEMENT
IS-21089
EFD H3 VIP CONDENSER REPOSITIONING
IS-18106
KIT POWER STEERING TANK CONVERTION CUMMINS TO ZF WITH D13 ENGINE
MI16-32
Improved bearings are now available to replace the original bearings used on some Prevost vehicles idler pulleys.
IS-21072B
STEERING GATEWAY. Revision B - PIN 2 and 10 were inverted on connector A139
MI22-12B
Air Tanks Draining Sequence. Revision: B - General Update
MI22-12A
Air Tanks Draining Sequence. Revision: A - Erroneous Secondary & Accessory tanks location.
MI22-12
Air Tanks Draining Sequence
IS-17151C
Halogen to LED fog light replacement kit. Revision: C - Advanced kits canceled
IS-22902
TAG AXLE HUB FLANGE - ALTERNATE CAP SCREW
IS21-072
STEERING GATEWAY, revision A : Cancel watch dog removal from EFD part of the instruction
MI20-08C
STORAGE AND STARTUP GUIDELINES : part number updates
IS21-072A
STEERING GATEWAY Revision A Cancel watch dog removal from EFD part of the instruction
IS20-925A
CENTRAL HVAC MERV FILTERS INSTALLATION
IS20-932A
H3 SERIES ENVIROCARE - IONS AIR SANITIZER
MI18-16B
BOSCH HD10 ALTERNATOR DIAGNOSTIC GUIDE Revision B To avoid replacement of alternators that are in fact in good working order, perform the steps which follow to help you perform a more precise diagnosis.
MI21-06
Diesel Exhaust Fluid ( DEF ) Contamination In Fuel System, Inspection And Repair â From US10 to newer engine generation
Mi21-07A
RONT & TAG AXLE â UNITIZED HUB BEARING END PLAY VERIFICATION AND REPLACEMENT
IS-20925A
CENTRAL HVAC MERV FILTERS INSTALLATION REVA
IS-20025A
PREVOST AWARE ADAPTIVE CRUISE BRAKING (ACB) â FLR10 TO FLR21 RADAR SENSOR UPGRADE APPLICABLE TO: H3 SERIES VEHICLES EQUIPPED WITH ACB SYSTEM FLR10 RADAR SENSOR
MI20-19B
INTRODUCING A NEW ENGINE COOLANT INTO PREVOST SERVICE CENTER NETWORK
MI20-19A
Rev A: Mention added concerning DDC Series 60 engine SCA requirement
MI21-01
VOLVO I-SHIFT TRANSMISSION REPLACEMENT - DIFFERENCE BETWEEN CONNECTIONS AT THE TOP OF THE OIL FILTER HOUSING
MI20-19
INTRODUCING A NEW ENGINE COOLANT INTO SERVICE
MI02-17A
Revision : A Torque value reduced
MI18-02A
ENGINE OIL & FILTER CHANGE INTERVALS - VOLVO D13 ENGINE, FROM US10 Revision: A Updated for OBD20 engines
MI20-08B
STORAGE AND STARTUP GUIDELINES Revision: B Parts added to Suggested Material 08-10-2020
P040200
Engine Exhaust Gas Recirculation Differential Pressure - Mechanical system not responding properly US13 â US20 Emissions
U17_P040200
Engine Exhaust Gas Recirculation Differential Pressure - Mechanical system not responding properly US13 â US20 Emissions
MI20-12
JERKY, NOISY OR HARD TO TURN STEERING GEARBOX. HYDRAULIC END LIMITER ADJUSTMENT. All models â equipped with RB Bosch/ZF Servocom or Servocomtronic steering gearbox
MI20-08A
STORAGE AND STARTUP GUIDELINES: Rev A: 21516229 replaced by 23381562 20523393 replaced by 21454749 800383 removed 611471 replaced by 611360 70376808 replaced by 21036050 21396642 replaced by 20967831
MI20-09
PREVOST VEHICLE DISINFECTION PROCEDURE Revision A
MI20-08
STORAGE AND STARTUP GUIDELINES - ALL PREVOST VEHICLES & VOLVO 9700
P029800
Repair instructions to address fault codes P029800
P052400
Repair instructions to address fault codes P052400 Engine Oil Pressure Too Low
P054415
Repair instructions to address fault codes P054415 Exhaust Gas Temperature Sensor Bank 1 Sensor 1 - Circuit Short To Battery or Open
P105998
Repair instructions to address fault codes P105998 Gearbox Oil Temperature Sensor - Component orsystem over temperature
P107017
Repair instructions to address fault codes P107017 Gearbox Brake Valve (VAGB) - Circuit voltage above threshold
P107575
Repair instructions to address fault codes P107575 Clutch System - Emergency position not reachable
P10CE97
Repair instructions to address fault codes P10CE97 Reductant Return: No Flow Detected - Componentor System Operation Obstructed or Blocked
P203115
Repair instructions to address fault codes P203115 Exhaust Gas Temperature Sensor Bank 1 Sensor 2 - Circuit Short To Battery or Open
P203F00
Repair instructions to address fault codes P203F00 Reductant Level Low
P204713
Repair instructions to address fault codes P204713 Reductant Injection Valve Control Bank 1 Unit 1 â Circuit Open
P204A13
Repair instructions to address fault codes P204A13 Reductant Pressure Sensor - Circuit Open
P208464
Repair instructions to address fault codes P208464 Exhaust Gas Temperature Sensor Circuit Range/Performance Bank 1 Sensor 2 - Signal plausibility failure
P20E892
Repair instructions to address fault codes P20E892 Reductant Pressure Too Low - Performance orincorrect operation
P242A15
Repair instructions to address fault codes P242A15 Exhaust Gas Temperature Sensor Bank 1 Sensor 3 - Circuit Short To Battery or Open
P256000
Repair instructions to address fault codes P256000 Engine Coolant Level Low
U029D00
Repair instructions to address fault codes U029D00 Lost Communication With NOx Sensor "A"
U029E00
Repair instructions to address fault codes U029E00 Lost Communication With NOx Sensor "B"
U02A200
Repair instructions to address fault codes U02A200 Lost Communication with Reductant Quality Module
MI15-24
Added: Power cables for L.H. side alternator & fan drive breaker box
FUELFILTER
Repair instructions to address fault codes P008A-00; P0087-00
NOX_Conv1
Repair instructions to address fault codes P207F-00 - Reductant Quality
NOx_Conv2
Repair instructions to address fault codes P207F-00; P20EE-00
P021700
Repair instructions to address fault codes P021700 Engine Coolant Over Temperature Condition
IS-14076
This instruction sheets explains how to replace the fuel tank on H-series vehicles. (Replacing older series tanks by newer model)
IS-19921A
This instruction Sheet explains how to install a seatbelt cutter in the driver's area
IS-19066
This instruction sheet describes how to cut the air dryer bracket, to avoid dirt accumulation, and applies to vehicles with the air dryer located into the wheel pit .
IS-17151
THIS INSTRUCTION SHEET EXPLAINS HOW TO REPLACE HALOGEN FOG LIGHT TO LED'S
IS-19900D
ELECTRIC FAN DRIVE COOLING SYSTEM CONVERSION WITH BOSCH ALTERNATOR - H3 SERIES US10 COOLING SYSTEM
IS-19910C
ELECTRIC FAN DRIVE COOLING SYSTEM CONVERSION WITH DELCO REMY ALTERNATOR - H3 SERIES US10 up to GHG17
IS-19915
MP-1000 MULTIMEDIA PLAYER INSTALLATION
IS-17900A
WHEEL FENDER STAINLESS STEEL PROTECTOR
IS-18910
This instruction sheet shows how to install a flap over the diesel filling cap.
WB19-07
On the independent front suspension (IFS) of the vehicles affected by this bulletin, check and make sure that there is enough clearance between the brake hoses identified in the procedure and their respective support bracket.
MI15-43A
New aramid cord poly-v belts are now available to replace the polyester cord alternator belts previously used on Prevost vehicles.
MI16-34
THIS MAINTENANCE INFORMATION DESCRIBES THE STEPS TO BE FOLLOWED ON YOUR COMPUTER TO ADD THE VOLVO ENGINE BRAKE AUTO MODE ON THE VEHICLE. THE AUTO MODE MAY BE ADDED ON US10 AND OBD13 VEHICLES THAT WERE BUILT BEFORE THE INTRODUCTION OF THE VOLVO ENGINE BRAKE AUTO MODE ON THE ASSEMBLY LINE. THE VEHICLE MUST BE EQUIPPED WITH THE ALLISON TRANSMISSION AND VOLVO ENGINE BRAKE (VEB).
WB15-19G
ON THE VEHICLES AFFECTED BY THIS BULLETIN, VIBRATION IS CAUSING DAMAGE TO A/C COMPRESSOR AND COMPRESSOR HARNESS CONNECTORS. ADDITION OF A REINFORCEMENT BRACKET TO BITZER A/C COMPRESSOR IS NEEDED TO INCREASE THE INSTALLATION STIFFNESS AND REDUCE VIBRATION AMPLITUDE.
VBC-PREVOST 2
Bendix M-32QR ABS modulator valve replaced by new M-40QR valve.
WB-13-56
PREVOST: THERE IS A LEAK AT PRESSURE PROBE CONNECTION, OF THE AIR DRYER ASSEMBLY, AND O-RING IS DEFORMED DUE TO FITTING ARRANGEMENT AND NEED A METAL RING ADDED. MODEL 2013 H3-45, H3-45 VIP, LEMIRAGE XLII ENTERTAINER. *PE
MI-13-46
PREVOST: THE COMBINED CHARGING AND STARTING SYSTEM F81 FUSE, ON SOME COACHES, CAN UNEXPECTEDLY BLOW AND NEED A 3 AMP DIODE TO CORRESPONDING 24CO CIRCUIT TO PREVENT ELECTRICAL BACK FLOW TO FUSE. MODELS 2011-2013 H3, H3-45 VIP CONVERTED, X3-45, X3-45 VIP CONVERTED, XL2-45 ENTERTAINER CONVERTED. *PE
MI-13-06
PREVOST: TO INCREASE VEHICLE'S PERFORMANCE, A MODIFICATION OF HOSE CLAMP FOR COOLING SYSTEM CONNECTION, IS RECOMMENDED. MODELS 2010-13 H3, 2010-13 H3 VIP CONVERTED, 2010-13 X3, 2012-13 X3 VIP CONVERTED, 2010-13 MTH XL2 ENTERTAINER, 2011 MTH XL2 CONVERTED. *PE
WB-13-29
PREVOST: A CORRECTIVE MEASURE IS REQUIRED DUE TO BOLTS LOOSEN BY BEING TIGHTENED TO PART MADE OF RUBBER, CAUSING THE RADIATOR FAN CLUTCH TRIPOD TO COME LOOSE AND STRIKING RADIATOR CORE. *PE
WB-13-04
PREVOST: WHEN AUXILIARY FAN FAILS RUN, AN A/C LOW PRESSURE MESSAGE WILL APPEAR ON DASHBOARD AND A BYPASS PIPING AND VALVE ASSEMBLY MAY BE ADDED TO RESOLVE THE ISSUE. MODEL 2011-2013 H3-45 VIP SHELLS. *PE
Complaint counts are reports filed with NHTSA, not failure rates. A common model collects more of them than a rare one that breaks more often.