IS-23019A
Service Bulletin/Repair Instructions
Sway bar collars improvement. Revision A : Add front sway bar support replacement and change bolts lenght.
Vehicle report
Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
IS-23019A
Sway bar collars improvement. Revision A : Add front sway bar support replacement and change bolts lenght.
IS-23019
SWAY BAR COLLARS IMPROVEMENT
IS-22106
H3 LAVATORY FAN RETROFIT KIT
IS-21072B
STEERING GATEWAY. Revision B - PIN 2 and 10 were inverted on connector A139
MI22-12B
Air Tanks Draining Sequence. Revision: B - General Update
MI22-12A
Air Tanks Draining Sequence. Revision: A - Erroneous Secondary & Accessory tanks location.
MI22-12
Air Tanks Draining Sequence
IS-17151C
Halogen to LED fog light replacement kit. Revision: C - Advanced kits canceled
IS20-925A
CENTRAL HVAC MERV FILTERS INSTALLATION
IS-20925A
CENTRAL HVAC MERV FILTERS INSTALLATION REVA
MI20-08C
STORAGE AND STARTUP GUIDELINES: Periodically, circumstances arise requiring operators to temporarily park a coach in storage. Whether it is a few weeks or several months, sporadic out of service times or a full stop, Prevost recommends following the guidelines in this document during times when: ⢠The coach can be operated on a regular/weekly basis while in storage. ⢠The coach will be in storage for an extended period without any operation. ⢠The coach will return to service following an extended period of downtime.
IS-18091A
TIE ROD 610052 FIRST INSTALLATION INSTRUCTIONS: Use these instructions when replacing the drop joint tie rod on S82, S84 / S84U I-beam axles. The new tie rod will be adjusted to the length of the original; however, a steering alignment needs to be performed after replacement.
MI20-19A
Rev A: Mention added concerning DDC Series 60 engine SCA requirement
MI20-19
INTRODUCING A NEW ENGINE COOLANT INTO SERVICE
MI02-17A
Revision : A Torque value reduced
IS-19165A
LAVATORY FAN RETROFIT KIT Applicable for H3 Series coaches from R-1012 (1994) Revision A: Added installation detail at step 8
SCi20-16
FAN CLUTCH PLATE BOLTS RE-TORQUING
IS-20923
H3 DRIVERâS PARTITION LITE INSTALLATION
MI20-08B
STORAGE AND STARTUP GUIDELINES Revision: B Parts added to Suggested Material 08-10-2020
P040200
Engine Exhaust Gas Recirculation Differential Pressure - Mechanical system not responding properly US13 â US20 Emissions
MI20-12
JERKY, NOISY OR HARD TO TURN STEERING GEARBOX. HYDRAULIC END LIMITER ADJUSTMENT. All models â equipped with RB Bosch/ZF Servocom or Servocomtronic steering gearbox
MI20-08A
STORAGE AND STARTUP GUIDELINES: Rev A: 21516229 replaced by 23381562 20523393 replaced by 21454749 800383 removed 611471 replaced by 611360 70376808 replaced by 21036050 21396642 replaced by 20967831
IS-20905
HAND SANITIZER DISPENSER INSTALLATION
MI20-09
PREVOST VEHICLE DISINFECTION PROCEDURE
MI20-08
STORAGE AND STARTUP GUIDELINES - ALL PREVOST VEHICLES & VOLVO 9700
MI15-24
Added: Power cables for L.H. side alternator & fan drive breaker box
IS-14076
This instruction sheets explains how to replace the fuel tank on H-series vehicles. (Replacing older series tanks by newer model)
IS-04106B
THIS INSTRUCTION SHEET EXPLAINS HOW TO REPLACE CLUTCH AND RADIATOR FAN TRANSFER MECHANISM MOUNTING BASE
IS-18091
This Instruction Sheet explains how to perform the first installation of Tie Rod 610052 on Prevost vehicles equipped with Dana S82, S84 / S84U I-beam axles, 1994- today
IS-19915
MP-1000 MULTIMEDIA PLAYER INSTALLATION
MI18-45A
Vehicles identified below are compatible with a new tie rod design. This new tie rod 610052 has updated ball joints and a fine adjuster sleeve. It replaces former drop type ball joint tie rods. Refer to IS-18091 for installation instructions. This document details maintenance inspection and toe-in adjustment with the new design tie rod.
IS-17910A
MESSAGE CENTER DISPLAY (MCD) REPLACEMENT
MI07-04
PREVOST: OIL LUBRICATED WHEEL HUB BEARINGS. FOR MAXIMUM PERFORMANCES AND SAFETY, ENSURING THAT THE WHEEL HUBS ARE INSPECTED DAILY AND LUBRICATED IN REGULAR INTERVALS IS OF THE UTMOST IMPORTANCE. *JS
0410
INSPECTION & REPLACEMENT OF POWER STEERING PRESSURE HOSE. PREVOST. *TT
0416
MODIFICATION OF SPEED SENSOR CONNECTORS ON ALLISON WORLD TRANSMISSION. PREVOST. *TT
0404
REPLACEMENT OF HOSES AND CLAMPS AND VERIFICATION OF MINIMUM CLEARANCE ON THE CHARGE AIR COOLER (CAC) SYSTEM. PREVOST WARRANTY BULLETIN. VARIOUS PREVOST 2004 MODELS. *TT
0311
ELIMINATION OF CONNECTOR C530, C531 & C532 FROM THE INTERIOR FLUORESCENT LIGHTING AND READING LIGHTS FUSE HOLDER. THIS INCLUDES MODEL YEAR 2004 MODELS. *TT
Complaint counts are reports filed with NHTSA, not failure rates. A common model collects more of them than a rare one that breaks more often.