Vehicle report
Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
MI26-00
The gasket thickness was increased from 1.5 mm to 3 mm to prevent interference between the collar ends, which previously made it impossible to reach the specified tightening torque. Increasing the gasket thickness ensures sufficient clearance between the collar ends and thus guarantees optimal tightening.
IS-23019A
Sway bar collars improvement. Revision A : Add front sway bar support replacement and change bolts lenght.
IS-23019
SWAY BAR COLLARS IMPROVEMENT
IS-22106
H3 LAVATORY FAN RETROFIT KIT
IS-18106
KIT POWER STEERING TANK CONVERTION CUMMINS TO ZF WITH D13 ENGINE
MI16-32
Improved bearings are now available to replace the original bearings used on some Prevost vehicles idler pulleys.
IS-21072B
STEERING GATEWAY. Revision B - PIN 2 and 10 were inverted on connector A139
MI22-12B
Air Tanks Draining Sequence. Revision: B - General Update
MI22-12A
Air Tanks Draining Sequence. Revision: A - Erroneous Secondary & Accessory tanks location.
MI22-12
Air Tanks Draining Sequence
IS-17151C
Halogen to LED fog light replacement kit. Revision: C - Advanced kits canceled
MI20-08C
STORAGE AND STARTUP GUIDELINES : part number updates
IS20-925A
CENTRAL HVAC MERV FILTERS INSTALLATION
is_20089
LAVATORY COMPARTMENT SLIDING DOOR LATCH IMPROVEMENT
IS-08080B
Sound Selector replacement, VSS04 to VSS05; When replacing a vehicle sound selector model VSS04 with a new sound selector model VSS05, an interface harness is required to connect the vehicle harness to the new sound selector model and a new VSS05 compatible radio unit must also be installed. This procedure describes the steps required to perform this update.
IS-20925A
CENTRAL HVAC MERV FILTERS INSTALLATION REVA
IS-18091A
TIE ROD 610052 FIRST INSTALLATION INSTRUCTIONS: Use these instructions when replacing the drop joint tie rod on S82, S84 / S84U I-beam axles. The new tie rod will be adjusted to the length of the original; however, a steering alignment needs to be performed after replacement.
MI20-19B
INTRODUCING A NEW ENGINE COOLANT INTO PREVOST SERVICE CENTER NETWORK
MI20-19A
Rev A: Mention added concerning DDC Series 60 engine SCA requirement
MI20-19
INTRODUCING A NEW ENGINE COOLANT INTO SERVICE
MI02-17A
Revision : A Torque value reduced
IS-19165A
LAVATORY FAN RETROFIT KIT Applicable for H3 Series coaches from R-1012 (1994) Revision A: Added installation detail at step 8
SCi20-16
FAN CLUTCH PLATE BOLTS RE-TORQUING
IS-20923
H3 DRIVERâS PARTITION LITE INSTALLATION
IS-20922
SIGMA PASSENGER SEATS PARTITION KIT
MI20-08B
STORAGE AND STARTUP GUIDELINES Revision: B Parts added to Suggested Material 08-10-2020
P040200
Engine Exhaust Gas Recirculation Differential Pressure - Mechanical system not responding properly US13 â US20 Emissions
MI20-12
JERKY, NOISY OR HARD TO TURN STEERING GEARBOX. HYDRAULIC END LIMITER ADJUSTMENT. All models â equipped with RB Bosch/ZF Servocom or Servocomtronic steering gearbox
MI20-08A
STORAGE AND STARTUP GUIDELINES: Rev A: 21516229 replaced by 23381562 20523393 replaced by 21454749 800383 removed 611471 replaced by 611360 70376808 replaced by 21036050 21396642 replaced by 20967831
IS-20906
Plexiglass Shield Behind Driver H3 Series
IS-20905
HAND SANITIZER DISPENSER INSTALLATION
MI20-09
PREVOST VEHICLE DISINFECTION PROCEDURE
MI20-08
STORAGE AND STARTUP GUIDELINES - ALL PREVOST VEHICLES & VOLVO 9700
MI15-24
Added: Power cables for L.H. side alternator & fan drive breaker box
IS-14076
This instruction sheets explains how to replace the fuel tank on H-series vehicles. (Replacing older series tanks by newer model)
IS-17151
THIS INSTRUCTION SHEET EXPLAINS HOW TO REPLACE HALOGEN FOG LIGHT TO LED'S
IS-19043
THIS INSTRUCTION SHEET EXPLAINS HOW TO RELOCATE THE WHEEL CHAIR LIFT PARCEL RACK FAN
IS-18091
This Instruction Sheet explains how to perform the first installation of Tie Rod 610052 on Prevost vehicles equipped with Dana S82, S84 / S84U I-beam axles, 1994- today
IS-19915
MP-1000 MULTIMEDIA PLAYER INSTALLATION
MI18-45A
Vehicles identified below are compatible with a new tie rod design. This new tie rod 610052 has updated ball joints and a fine adjuster sleeve. It replaces former drop type ball joint tie rods. Refer to IS-18091 for installation instructions. This document details maintenance inspection and toe-in adjustment with the new design tie rod.
IS-17910A
MESSAGE CENTER DISPLAY (MCD) REPLACEMENT
IS-19916
This instruction sheet explains how to install the Audio Converter 405842
IS-08006A
This instruction sheet explains how to relocate engine door gas spring.
IS-08006
This instruction sheet explains how to relocate engine door gas spring.
IS-11003G
This Instruction sheet explains how to replace the ?MASTER ID? WITH ?MCM? Module
IS-11003F
This Instruction sheet explains how to replace the "MASTER ID WITH MCM" Module
SCI17-35
This internal instruction explains how to bench program the FMS gateway module used in the ELD (Electronic Logging Device) interface kit for pre-OBD13 vehicles.
IS-17907
This instruction sheet explains how to install the Volvo Electronic Logging Device (ELD)
CK17-19A
This conversion kit explains how to remove TGW1 from vehicles using Tech Tool, no manual VDA changes needed. This conversion kit will work for any vehicle equipped with TGW1 up to the VIN's listed on the bulletin.
IS-11003E
This Instruction sheet explains how to remplace MASTER ID? WITH ?MCM? Module
IS-17901
This instructions sheet explains how to program a Wabco Smart Trac ABS ECU.
IS-16903
This instruction sheet explains how to replace the two older generation (brush type) condenser fans by four newer style (brushless) fans.
IS-16100
This instruction sheet explains how to install latest radio models
IS-17900
This Instruction Sheet explains how to install a wheel fender stainless steel protector
MI16-08
On receiving your Kit Masters fan clutch you may notice a new method of locking the electromagnetic clutch in the event of a failure. These new electromagnetic clutches will feature locking tabs in replacement of the locking bolts. Applies to part number 550965; 550966 &550974.
IS-08080A
WHEN REPLACING A VEHICLE SOUND SELECTOR MODEL VSS04 WITH A NEW SOUND SELECTOR MODEL VSS05, AN INTERFACE HARNESS IS REQUIRED TO CONNECT THE VEHICLE HARNESS TO THE NEW SOUND SELECTOR MODEL AND A NEW VSS05 COMPATIBLE RADIO UNIT MUST ALSO BE INSTALLED. THIS PROCEDURE DESCRIBES THE STEPS REQUIRED TO PERFORM THIS UPDATE.
MI16-15B
The Beru sensors used on Prevost vehicles to monitor tire pressure (TPMS system) are being replaced by new Huf sensors and their corresponding stainless valves stems. Since the older and newer sensors are using different valve stems, replacement of a defective sensor on older vehicles will require the use of a new kit number (valve stem and sensor assembly). The table below provides a quick overview between the older and newer part numbers depending on wheel application.
IS-11003D
This Instruction sheet explains how to remplace MASTER ID? WITH ?MCM? MODULE
MI16-22
Use this maintenance information procedure to resolve an undesired behaviour on 2008-2012 vehicles. In sleep mode, certain marker lights may remain illuminated.
MI16-15A
The Beru sensors used on Prevost vehicles to monitor tire pressure (TPMS system) are being replaced by new Huf sensors and their corresponding stainless valves stems. Since the older and newer sensors are using different valve stems, replacement of a defective sensor on older vehicles will require the use of a new kit number (valve stem and sensor assembly). The table below provides a quick overview between the older and newer part numbers depending on wheel application.
IS-14085
This Instruction sheet explains how to prevent AC Copper Pipes Chaffing at Engine Bulkhead
Mi16-15
The Beru sensors used on Prevost vehicles to monitor tire pressure (TPMS system) are being replaced by new Huf sensors and their corresponding stainless valves stems. Since the older and newer sensors are using different valve stems, replacement of a defective sensor on older vehicles will require the use of a new kit number (valve stem and sensor assembly). The table below provides a quick overview between the older and newer part numbers depending on wheel application.
MI15-51
This Maintenance Information explains how to run a n Air Conditionning performance test
MI15-61
This Maintrenance infomration explains that the Castrol Syntrans oil isn?t fully approved for 500 000 miles (800 000 km) extended drain intervals on the Volvo I-Shift transmission. For this reason, this oil has been downgraded to regular drain intervals. Find below, a list of Volvo?s approved oils for extended drain as well as regular drain intervals.
MI15-56
On vehicles mentioned above, should the curbside electric sunshade fail to operate without encountering a drive mechanism issue, perform the following procedure.
IS-11003A
This Instruction sheet explains how to replace MASTER ID? WITH ?MCM? MODULE
MI15-18
This Maintenance Information does explain how five year old vehicles and older should be subjected to a thorough structural inspection.
MI15-02
This Maintenance Information presents an improved differential breather kit, identical to the one now used in production. This new breather incorporates a "J" shaped hose that prevents oil leakage and water ingestion while allowing the axle to vent.
MI1423
A new software version (v1.06) is available to update the CANtrak (Tire Pressure Monitoring System) module. This new version will allows a 10 min. delay before the ?SYSTEM ERROR NOT ALL TIRES MONITORED? message appears in the vehicle cluster when a tire pressure sensor loses its connection. NOTE: The new software version will only delays the cluster message, the CANtrak screen will still displays a ??? code for the corresponding pressure sensor.
IS-14900
This Instruction Sheet explains how to replace 562489 Dimmer, using kit #069136
IS-08080
When replacing a vehicle sound selector model VSS04 with a new sound selector model VSS05, an interface harness is required to connect the vehicle harness to the new sound selector model and a new VSS05 compatible radio unit must also be installed. This procedure describes the steps required to perform this update.
MI13-33
This Maintenance Information explains that polyester reinforced silicone hoses and elbowscan be repalced by aramid reinforced hoses and elbows for improved long term durability, and that constant torque hose clamps for silicone hoses with 5/8po, 3/4po, 7/8po, 1 1/8po and 1 3/8po inside diameter (I.D) can be replaced by new WAVE SEAL type constant torque hose clamps.
SP13-320
On the vehicles affected by this bulletin, if needed, the celling panel needs to be removed and material glued again.
SP13-322
On the vehicles affected by this bulletin, relocate the video fuse in the SMI box closer to the door for better access.
SP13-306
On the vehicles affected by this bulletin, replace the Exhaust Gas Recirculation Venturi tube and sensor for an improved design.
WB12-31B
On the vehicles affected by this bulletin, a new and improved dipstick is available for installation.
MI11-27
PREVOST: 12" BRUSHLESS CONDENSER FAN REPLACEMENT. MODELS INCLUDE XLII MTH, AND H3VIP MTH. MODEL YEARS ARE 2008-2011. *KB
WB11-05
PREVOST: EXHAUST PIPE ANGLE BRACKET INSPECTION. *KB
WB11-22
PREVOST: VOLVO D13 ENGINE HARNESS REPLACEMENT - OIL SEEPAGE AT UNIT INJECTOR PASS - THROUGH FITTING. *KB
SCI11-11
PREVOST: KIDDE FIRE EXTINGUISHER CONTROL HEAD REPLACEMENT. *KB UPDATED 5/9/2012. *KB
WB11-02
PREVOST: REPLACING T1 BOSCH ALTERNATORS AND WATER PUMP BELT TENSIONERS. *KB
WB11-01A
PREVOST: VOLVO D13 ENGINE - AFTERTREATMENT HYDROCARBON INJECTOR (AHI) FUEL LINE FITTINGS - PROPER TIGHTENING VERIFICATION. *KB
WB10-18
PREVOST: VOLVO D13 ENGINE OIL SEEPAGE AT UNIT INJECTOR HARNESS PASS-THROUGH FITTING. *KB
WB10-15A
PREVOST: VOLVO D13 ENGINE - NEW EGR MIXER INLET TUBE. *KB
WB10-17
PREVOST: VOLVO D13 ENGINE - TURBOCHARGER SMART REMOTE ACTUATOR (SRA) FAULTS. *KB
WB10-01A
PREVOST: VOLVO D13 ENGINE: REPLACEMENT OF COPPER INJECTOR SLEEVE WITH CONICAL STAINLESS STEEL INJECTOR SLEEVE. *KB UPDATED 5/4/2012. *KB
SCI10-02
PREVOST: INSTALLIN AN AIR DEFLECTOR IN ORDER TO REDUCE AMBIENT TEMPERATURE AROUND LINNIG RADIATOR FAN GEARBOX. *KB
WB09-13A
PREVOST: INSPECTING THE RADIATOR FAN DRIVE MECHANISM SUPPORT ON A DETROIT DIESEL ENGINE. ALSO INCLUDED MODEL VIP-45 BUS MODEL YEARS 2001-2010; MODEL XLII MTH BUS MODEL YEARS 2008-2009. *JS
SCI09-28
PREVOST: INSTALLING THREE-POINT PASSENGER SEAT RESTRAINT SYSTEM. THE PURPOSE OF THE FOLLOWING PROCEDURE IS TO FACILITATE THE JOB AND TO HELP IDENTIFY THE DIFFICULT AREAS. ALSO INCLUDED MODELS HE-41 AND HE-45 COACHES MODEL YEARS 1998-2008; MODEL XLII AND X3-45 COACHES MODEL YEARS 1998-2008. *JS
WB09-24
PREVOST: CHECK IF VOLVO ENGINES ARE NOT EQUIPPED WITH 'DAVCO FUEL PRO 382' FILTER ARE FITTED WIH TWO FUEL FILTERS. *JS
WB09-26
PREVOST: ON VOLVO D13 ENGINES DASHBOARD 'CHECK ENGINE' WARNING LAMP COULD COME ON DUE TO CODE PID 171. ALSO INCLUDED MODEL MTH XLII-45E BUS SHELLS MODEL YEAR 2009. *JS
WB09-25
PREVOST: ON VOLVO D13 ENGINES DASHBOARD 'CHECK ENGINE' WARNING LAMP COULD COME ON DUE TO CODE PID 110. ALSO INCLUDED MODEL MTH XLL45E BUS MODEL YEAR 2009 *JS
WB09-01
PREVOST: COACHES EXHAUST SYSTEM UPDATE IN ORDER TO MODIFY EXHAUST FUMES PATH, INCREASE DIFFUSER PERFORMANCE AND REFLECT LATEST IMPROVEMENT. MODELS INCLUDE H3-41 AND H3-45 MODEL YEARS 2007-2009; MODEL X3-45 MODEL YEAR 2008. *JS
WB08-15
PREVOST: VOLVO D13 ENGINE WITH VEB (VOLVO ENGINE BRAKE)- ROCKER ARMS REPLACEMENT & CAMSHAFT INSPECTION (REF. SP215-015) CONTACT YOUR PREVOST REGIONAL SERVICE MANAGER TO FIND OUT THE NEAREST SERVICE CENTER LOCATION. *JS
WB08-18
PREVOST: VOLVO D13 ENGINE- WATER PUMP REPLACEMENT (REF. SP262-003). *JS
MI08-04
FRONT AND TAG AXLE HUB BEARING AND KING PIN PERIODIC MAINTENANCE. BEARINGS MUST BE INSPECTED AT INTERVALS OF 30,000 MILES (48 000KM). KING PINS SHOULD BE SERVICED EVERY 6, 250 MILES (10,000 KM) OR TWICE A YEAR. ALSO INCLUDED MODEL VIP-45 MTH MODEL YEARS 2004-2008. MODEL XLII MTH MODEL YEARS 2004-2008. *JS
WB08-13
PREVOST: REPLACEMENT OF THE DASHBOARD STATIONARY REGENERATION SWITCH- DETROIT DIESEL ONLY.THIS SWITCH WOULD NOT BE ABLE TO INITIATE A STAIONARY REGENERATION AFTER DDEC VI SOFTWARE UPGRADE. ALSO INCLUDED MODEL VIP MOTORHOMES MODEL YEARS 2007-2008; MODEL XLII MOTORHOMES MODEL YEAR 2008; MODEL ENTERTAINER MODEL YEARS 2008-2009. *JS
WB08-07
IMPROVED AIR CIRCULATION ON H3 COACHES EQUIPPED WITH WCL AND SLIDING DOOR. IN ORDER TO IMPROVE THE PASSENGERS COMFORT IT IS NECESSARY TO INCREASE THE AIR CIRCULATION IN THE OVERHEAD COMPARTMENT AS WELL AS BEHIND THE WHEELCHAIR LIFT DOOR. *JS
WB07-12
REPLACE THE PIPE CONNECTING THE TURBOCOMPRESSOR TO THE CHARGE AIR COOLER. POSSIBILITY THAT THE PIPE STRIKES AGAINST THE RADIATOR FAN DRIVE MECHANISM SUPPORT. ABRASION OR PERFORATION COULD RESULT AND THUS RESULT IN DAMAGE TO DIESEL PARTICULATE OR LOSS OF ENGINE PERFORMANCE. ALSO INCLUDED MODEL VIP-45 MTH. MODEL YEAR 2007. *JS
Complaint counts are reports filed with NHTSA, not failure rates. A common model collects more of them than a rare one that breaks more often.