Vehicle report
Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
MI26-00
The gasket thickness was increased from 1.5 mm to 3 mm to prevent interference between the collar ends, which previously made it impossible to reach the specified tightening torque. Increasing the gasket thickness ensures sufficient clearance between the collar ends and thus guarantees optimal tightening.
IS-23019A
Sway bar collars improvement. Revision A : Add front sway bar support replacement and change bolts lenght.
IS-23019
SWAY BAR COLLARS IMPROVEMENT
IS-22106
H3 LAVATORY FAN RETROFIT KIT
IS-18106
KIT POWER STEERING TANK CONVERTION CUMMINS TO ZF WITH D13 ENGINE
IS-21072B
STEERING GATEWAY. Revision B - PIN 2 and 10 were inverted on connector A139
IS-22055
H3 SERIES LED HEADLAMPS RETROFIT
MI22-12B
Air Tanks Draining Sequence. Revision: B - General Update
MI22-12A
Air Tanks Draining Sequence. Revision: A - Erroneous Secondary & Accessory tanks location.
SP18-35J
P20EE (diagnostic troubleshooting code) SOLUTION - NOX CONVERSION EFFICIENCY. Revision J - Range of applicable VINs updated.
MI22-12
Air Tanks Draining Sequence
IS-17151C
Halogen to LED fog light replacement kit. Revision: C - Advanced kits canceled
IS-22902
TAG AXLE HUB FLANGE - ALTERNATE CAP SCREW
IS21-072
STEERING GATEWAY, revision A : Cancel watch dog removal from EFD part of the instruction
MI20-08C
STORAGE AND STARTUP GUIDELINES : part number updates
WB22-07
TGW PROGRAMMING
IS21-072A
STEERING GATEWAY Revision A Cancel watch dog removal from EFD part of the instruction
IS20-925A
CENTRAL HVAC MERV FILTERS INSTALLATION
IS20-932A
H3 SERIES ENVIROCARE - IONS AIR SANITIZER
IS22-040
BRAKE PEDAL SEAL PLATE INSTALLATION KIT
SP18-35H
P20EE (diagnostic troubleshooting code) SOLUTION - NOX CONVERSION EFFICIENCY
SP18-39D
SCR CONVERTER REPLACEMENT - AFTERTREATMENT SYSTEM
MI21-13A
An automated test is available to check the big HVAC superheat from the driver seat. This test is controlled by Multiplex, eliminating interventions and the need to take measures on the vehicle.
SR19-31C
ENGINE CONTROL MODULE (ECM) SOFTWARE UPDATE - Engine Cooling Strategy in High Altitude Operation Revision C: VIN range in application box rearranged for H3 coaches
MI21-06
Diesel Exhaust Fluid ( DEF ) Contamination In Fuel System, Inspection And Repair â From US10 to newer engine generation
is_20089
LAVATORY COMPARTMENT SLIDING DOOR LATCH IMPROVEMENT
Mi21-07A
RONT & TAG AXLE â UNITIZED HUB BEARING END PLAY VERIFICATION AND REPLACEMENT
IS-18042
EBERSPACHER PREHEATER INSTALLATION In replacement of Spheros & Valeo preheaters
SP18-35F
P20EE (diagnostic troubleshooting code) SOLUTION - NOX CONVERSION EFFICIENCY Rev E: expiration date removed
MI20-13A
SIDE CAMERA REAR VIEW SYSTEM â CAMERA ADJUSTMENT â H3 & X3 SERIES
IS-19037B
PREVOST DRIVER ASSIST SYSTEM CAMERA & HEAD-UP-DISPLAY INSTALLATION ON H3 SERIES
IS-20932A
H3 SERIES ENVIROCARE - IONS AIR SANITIZER REV A
IS-20925A
CENTRAL HVAC MERV FILTERS INSTALLATION REVA
IS-20932
H3 SERIES ENVIROCARE - IONS AIR SANITIZER
is_19037a
PREVOST DRIVER ASSIST SYSTEM CAMERA & HEAD-UP-DISPLAY INSTALLATION ON H3 SERIES
IS-18091A
TIE ROD 610052 FIRST INSTALLATION INSTRUCTIONS: Use these instructions when replacing the drop joint tie rod on S82, S84 / S84U I-beam axles. The new tie rod will be adjusted to the length of the original; however, a steering alignment needs to be performed after replacement.
IS-19037
PREVOST DRIVER ASSIST SYSTEM CAMERA & HEAD-UP-DISPLAY INSTALLATION ON H3 SERIES
MI20-19B
INTRODUCING A NEW ENGINE COOLANT INTO PREVOST SERVICE CENTER NETWORK
MI20-19A
Rev A: Mention added concerning DDC Series 60 engine SCA requirement
MI21-01
VOLVO I-SHIFT TRANSMISSION REPLACEMENT - DIFFERENCE BETWEEN CONNECTIONS AT THE TOP OF THE OIL FILTER HOUSING
SP18-35E
P20EE (diagnostic troubleshooting code) SOLUTION - NOX CONVERSION EFFICIENCY Rev E: expiration date removed
SP18-39C
SCR CONVERTER REPLACEMENT - AFTERTREATMENT SYSTEM Revision: C Expiration date removed 12/22/2020
MI20-19
INTRODUCING A NEW ENGINE COOLANT INTO SERVICE
MI02-17A
Revision : A Torque value reduced
MI18-02A
ENGINE OIL & FILTER CHANGE INTERVALS - VOLVO D13 ENGINE, FROM US10 Revision: A Updated for OBD20 engines
PCN2017151
The halogen fog lights have been replaced by led lights. Installation of the new lights is different. New supports to enable the beam to be adjusted with a screw when the bumper is closed (due to the precision required to perform the adjustment).
IS-19165A
LAVATORY FAN RETROFIT KIT Applicable for H3 Series coaches from R-1012 (1994) Revision A: Added installation detail at step 8
IS-13169A
PREVOST AWARE ADAPTIVE CRUISE BRAKING (ACB) FLR20 RADAR SENSOR REPLACEMENT KIT Revision A: KIT IS13169-1 & IS13169-2 CANCELED, USE 145373 &145372
MI20-14
PREVOST DRIVER ASSIST⢠- WINDSHIELD REPLACEMENT EQUIPPED WITH CAMERA
IS-20923
H3 DRIVERâS PARTITION LITE INSTALLATION
IS-20929
UV LIGHTS INSTALLATION IN AC COMPARTMENT
MI20-13
eMIRROR SIDE CAMERA SYSTEM ADJUSTMENT
IS-20922
SIGMA PASSENGER SEATS PARTITION KIT
MI20-08B
STORAGE AND STARTUP GUIDELINES Revision: B Parts added to Suggested Material 08-10-2020
P040200
Engine Exhaust Gas Recirculation Differential Pressure - Mechanical system not responding properly US13 â US20 Emissions
U17_P040200
Engine Exhaust Gas Recirculation Differential Pressure - Mechanical system not responding properly US13 â US20 Emissions
MI20-12
JERKY, NOISY OR HARD TO TURN STEERING GEARBOX. HYDRAULIC END LIMITER ADJUSTMENT. All models â equipped with RB Bosch/ZF Servocom or Servocomtronic steering gearbox
MI18-18B
GENERAL HOISTING AND TOWING PROCEDURES Revision: B Updated 2.1 to show rubber chocks, secure front and rear.
IS-19905F
BOSCH TO DELCO REMY ALTERNATOR INSTALLATION, H3-45 WITH ELECTRIC FAN DRIVE; Revision F Updated ALTTYP parameter value name.
MI20-08A
STORAGE AND STARTUP GUIDELINES: Rev A: 21516229 replaced by 23381562 20523393 replaced by 21454749 800383 removed 611471 replaced by 611360 70376808 replaced by 21036050 21396642 replaced by 20967831
IS-20906
Plexiglass Shield Behind Driver H3 Series
IS-19084
Accessory air filter replacement Replaces 642192
MI20-09
PREVOST VEHICLE DISINFECTION PROCEDURE Revision A
IS-19064
BAGGAGE DOOR SEAL REPLACEMENT
IS-20905
HAND SANITIZER DISPENSER INSTALLATION
MI20-08
STORAGE AND STARTUP GUIDELINES - ALL PREVOST VEHICLES & VOLVO 9700
P029800
Repair instructions to address fault codes P029800
P052400
Repair instructions to address fault codes P052400 Engine Oil Pressure Too Low
P054415
Repair instructions to address fault codes P054415 Exhaust Gas Temperature Sensor Bank 1 Sensor 1 - Circuit Short To Battery or Open
P105998
Repair instructions to address fault codes P105998 Gearbox Oil Temperature Sensor - Component orsystem over temperature
P107017
Repair instructions to address fault codes P107017 Gearbox Brake Valve (VAGB) - Circuit voltage above threshold
P107575
Repair instructions to address fault codes P107575 Clutch System - Emergency position not reachable
P10CE97
Repair instructions to address fault codes P10CE97 Reductant Return: No Flow Detected - Componentor System Operation Obstructed or Blocked
P203115
Repair instructions to address fault codes P203115 Exhaust Gas Temperature Sensor Bank 1 Sensor 2 - Circuit Short To Battery or Open
P203F00
Repair instructions to address fault codes P203F00 Reductant Level Low
P204713
Repair instructions to address fault codes P204713 Reductant Injection Valve Control Bank 1 Unit 1 â Circuit Open
P204A13
Repair instructions to address fault codes P204A13 Reductant Pressure Sensor - Circuit Open
P208464
Repair instructions to address fault codes P208464 Exhaust Gas Temperature Sensor Circuit Range/Performance Bank 1 Sensor 2 - Signal plausibility failure
P20E892
Repair instructions to address fault codes P20E892 Reductant Pressure Too Low - Performance orincorrect operation
P242A15
Repair instructions to address fault codes P242A15 Exhaust Gas Temperature Sensor Bank 1 Sensor 3 - Circuit Short To Battery or Open
P256000
Repair instructions to address fault codes P256000 Engine Coolant Level Low
U029D00
Repair instructions to address fault codes U029D00 Lost Communication With NOx Sensor "A"
U029E00
Repair instructions to address fault codes U029E00 Lost Communication With NOx Sensor "B"
U02A200
Repair instructions to address fault codes U02A200 Lost Communication with Reductant Quality Module
MI15-24
Added: Power cables for L.H. side alternator & fan drive breaker box
FUELFILTER
Repair instructions to address fault codes P008A-00; P0087-00
NOX_Conv1
Repair instructions to address fault codes P207F-00 - Reductant Quality
NOx_Conv2
Repair instructions to address fault codes P207F-00; P20EE-00
P021700
Repair instructions to address fault codes P021700 Engine Coolant Over Temperature Condition
IS-14076
This instruction sheets explains how to replace the fuel tank on H-series vehicles. (Replacing older series tanks by newer model)
IS-19921A
This instruction Sheet explains how to install a seatbelt cutter in the driver's area
IS-19066
This instruction sheet describes how to cut the air dryer bracket, to avoid dirt accumulation, and applies to vehicles with the air dryer located into the wheel pit .
IS-17151
THIS INSTRUCTION SHEET EXPLAINS HOW TO REPLACE HALOGEN FOG LIGHT TO LED'S
IS-19043
THIS INSTRUCTION SHEET EXPLAINS HOW TO RELOCATE THE WHEEL CHAIR LIFT PARCEL RACK FAN
SP18-35D_English
On vehicles with active code P20EE, perform the following checklist and operations.
IS-18091
This Instruction Sheet explains how to perform the first installation of Tie Rod 610052 on Prevost vehicles equipped with Dana S82, S84 / S84U I-beam axles, 1994- today
IS-19915
MP-1000 MULTIMEDIA PLAYER INSTALLATION
Wb19-11
On the vehicles affected by this bulletin, the vehicle program might need to be upgraded to prevent batteries drain when ISM (Intelligent Sleep Mode) is enabled.
IS-19911C
INTELLIGENT SLEEP MODE INSTALLATION
Mi14-34D
PREVOST AWARE ADAPTIVE CRUISE BRAKING (ACB) - FLR20 & FLR21 RADAR SENSOR ALIGNMENT
MI18-45A
Vehicles identified below are compatible with a new tie rod design. This new tie rod 610052 has updated ball joints and a fine adjuster sleeve. It replaces former drop type ball joint tie rods. Refer to IS-18091 for installation instructions. This document details maintenance inspection and toe-in adjustment with the new design tie rod.
IS-17900A
WHEEL FENDER STAINLESS STEEL PROTECTOR
IS-18910
This instruction sheet shows how to install a flap over the diesel filling cap.
CK19-16
ISRI SEAT BELT WITH SENSOR INSTALLATION (ACCESSORY KIT 23687694)
SP19-15A
On the vehicles affected by this bulletin, the Brigade camera system parameters must be set up and the system rebooted to enable activation.
SP18-35C_English
On vehicles with active code P20EE, perform the following checklist and operations.
IS-19905D
This instruction sheet explains how to install Delco Remy Alternators on H3 vehicles equipped with Electric Fan Drive
WB19-07
On the independent front suspension (IFS) of the vehicles affected by this bulletin, check and make sure that there is enough clearance between the brake hoses identified in the procedure and their respective support bracket.
SCI19-21
This document shows how to install exterior perimeter cameras and interior cameras. It also shows how to make the setup with the monitor
IS-19905C
This instruction sheet explains how to install Delco Remy Alternators on H3 vehicles equipped with EFD (Electric Fan Drive)
SP19-15
On the vehicles affected by this bulletin, the Brigade camera system parameters must be set up and the system rebooted to enable activation.
WB19-02A
On the vehicles affected by this bulletin replace the idler and belt tensioner support on the left side (hot side) of the engine by an improved part, 011213. This applies to installations with Bosch or Delco Remy alternators on the hot side (left side) of the engine.
IS-18115
This instruction sheet explains how to install a GM Glove box Lock on H-Series vehicles
IS-19905
This instruction sheet explains how to install Delco Remy Alternators on H3 vehicles equipped with EFD
SP18-35B_English
On vehicles with active code P20EE, perform the following checklist and operations.
SP18-39B
This Special Bulletin explains how to perform the replacement of the SCR tank, when authorized.
MI19-05
This Maintenance Information expains how to adjust p/n 660865, 660699 draglinks
MI19-06
This Maintenance Information is published to answer some questions regarding the inverted or ?trailing? mounting position of the drive axle brake calipers on Prevost vehicles
SP18-49A
On the vehicles affected by this bulletin, an inspection of the upper steering column universal joint must be performed.
SCI18-46
This Service Center Instructions explains how to install the Prevost Ultimate Entertainment System
SP18-49
On the vehicles affected by this bulletin, an inspection of the upper steering column universal joint must be performed.
Sp18-39A
This Special Bulletin explains how to perform the replacement of the SCR tank, when authorized.
WB18-43
This Warranty Bulletin explains how to update the VECU (Vehicle Electronic Control Unit) parameters to allow auto engine brake function with the I-Shift transmission.
IS-18905
This instruction sheet explains how to install hatches with fan on H3 vehicles.
MI18-45
This Maintenance Information presents the new maintenance inspections and new method to adjust toe-in of vehicles equipped with new tie rod 610052.
SP18-39
This Special Bulletin explains how to perform the replacement of the SCR tank, when authorized.
Sp18-35
On vehicles with active code P20EE, perform the following checklist and operations.
WB18-04
On the vehicles affected by this bulletin, update EMS and ACM software to the latest version available.
VBC-PREVOST 4
Communication letter from Accociate Administration for Enforcement, NHTSA From Prevost Subject Vehicle Brand: Prevost (EWR#000650)
Complaint counts are reports filed with NHTSA, not failure rates. A common model collects more of them than a rare one that breaks more often.