MI16-32
Service Bulletin/Repair Instructions
Improved bearings are now available to replace the original bearings used on some Prevost vehicles idler pulleys.
Vehicle report
Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
MI16-32
Improved bearings are now available to replace the original bearings used on some Prevost vehicles idler pulleys.
IS-21072B
STEERING GATEWAY. Revision B - PIN 2 and 10 were inverted on connector A139
MI22-12B
Air Tanks Draining Sequence. Revision: B - General Update
MI22-12A
Air Tanks Draining Sequence. Revision: A - Erroneous Secondary & Accessory tanks location.
SP18-35J
P20EE (diagnostic troubleshooting code) SOLUTION - NOX CONVERSION EFFICIENCY. Revision J - Range of applicable VINs updated.
MI22-12
Air Tanks Draining Sequence
IS-17151C
Halogen to LED fog light replacement kit. Revision: C - Advanced kits canceled
IS-22902
TAG AXLE HUB FLANGE - ALTERNATE CAP SCREW
IS21-072
STEERING GATEWAY, revision A : Cancel watch dog removal from EFD part of the instruction
MI20-08C
STORAGE AND STARTUP GUIDELINES : part number updates
IS21-072A
STEERING GATEWAY Revision A Cancel watch dog removal from EFD part of the instruction
IS20-925A
CENTRAL HVAC MERV FILTERS INSTALLATION
IS20-932A
H3 SERIES ENVIROCARE - IONS AIR SANITIZER
IS22-040
BRAKE PEDAL SEAL PLATE INSTALLATION KIT
SP18-39D
SCR CONVERTER REPLACEMENT - AFTERTREATMENT SYSTEM
SP18-35H
P20EE (diagnostic troubleshooting code) SOLUTION - NOX CONVERSION EFFICIENCY
MI18-16B
BOSCH HD10 ALTERNATOR DIAGNOSTIC GUIDE Revision B To avoid replacement of alternators that are in fact in good working order, perform the steps which follow to help you perform a more precise diagnosis.
MI21-06
Diesel Exhaust Fluid ( DEF ) Contamination In Fuel System, Inspection And Repair â From US10 to newer engine generation
Mi21-07A
RONT & TAG AXLE â UNITIZED HUB BEARING END PLAY VERIFICATION AND REPLACEMENT
SP18-35F
P20EE (diagnostic troubleshooting code) SOLUTION - NOX CONVERSION EFFICIENCY Rev E: expiration date removed
IS-20925A
CENTRAL HVAC MERV FILTERS INSTALLATION REVA
MI20-19B
INTRODUCING A NEW ENGINE COOLANT INTO PREVOST SERVICE CENTER NETWORK
MI20-19A
Rev A: Mention added concerning DDC Series 60 engine SCA requirement
MI21-01
VOLVO I-SHIFT TRANSMISSION REPLACEMENT - DIFFERENCE BETWEEN CONNECTIONS AT THE TOP OF THE OIL FILTER HOUSING
MI20-19
INTRODUCING A NEW ENGINE COOLANT INTO SERVICE
MI20-08B
STORAGE AND STARTUP GUIDELINES Revision: B Parts added to Suggested Material 08-10-2020
MI20-12
JERKY, NOISY OR HARD TO TURN STEERING GEARBOX. HYDRAULIC END LIMITER ADJUSTMENT. All models â equipped with RB Bosch/ZF Servocom or Servocomtronic steering gearbox
MI18-18B
GENERAL HOISTING AND TOWING PROCEDURES Revision: B Updated 2.1 to show rubber chocks, secure front and rear.
MI20-08A
STORAGE AND STARTUP GUIDELINES: Rev A: 21516229 replaced by 23381562 20523393 replaced by 21454749 800383 removed 611471 replaced by 611360 70376808 replaced by 21036050 21396642 replaced by 20967831
MI20-09
PREVOST VEHICLE DISINFECTION PROCEDURE
MI20-08
STORAGE AND STARTUP GUIDELINES - ALL PREVOST VEHICLES & VOLVO 9700
MI15-24
Added: Power cables for L.H. side alternator & fan drive breaker box
FUELFILTER
Repair instructions to address fault codes P008A-00; P0087-00
NOX_Conv1
Repair instructions to address fault codes P207F-00 - Reductant Quality
NOx_Conv2
Repair instructions to address fault codes P207F-00; P20EE-00
Wb17-14B
On the vehicles affected by this bulletin, the power cable stud adapter on the alternator must be inspected and if needed, replaced.
WB18-04
On the vehicles affected by this bulletin, update EMS and ACM software to the latest version available.
MI18-18
This maintenance information explains how to tow and hoist Prevost vehicles.
MI18-16A
This Maintenance Information presents guidelines to help with the diagnosis of the Bosch HD10 alternators
MI18-21
This Maintenance Information presents information about the Bitzer A/C compressor oil change interval and reminds technicians to clean the oil filter/strainer and the magnetic drain plug.
MI18-02
This Mainteannce Informaiton presents the latest engine oil & filter change intervals for the Volvo Engine
MI16-17F
This Maintenance Information explains how to remove and install the Bosch HD10 (120A or 150A) alternators
IS-13009B
This instruction sheet explains how to install and adjust drag link # 660699
IS-17016
This instruciton sheet explains how to relocate the RV-3 Valve
MI17-22
This Maintenance Information explains how to inspect the Fuel Tank Cradle Mounting Screws on a yearly basis
CK17-30
On the vehicles affected by this bulletin, it is now possible to replace the older generation TGW 2.0 (3G network) by the newer 2.1 version (4G the network) using accessory kit 23266301 and the following procedure.
CK17-27
This conversion kit explains how to to disable the ACB radar.
Sp17-29
On the vehciles affected by this bulletin, perform a multiplex software update to correct unwanted behavior of the cruise control. The affected vehicles are equipped with a transmission retarder.
SCI16-40A
On the vehicles affected by this bulletin, replace the engine information decal located in the engine compartment.
WB16-33A
On the vehicles affected by this bulletin, replace the engine information decal located in the engine compartment.
MI16-15B
The Beru sensors used on Prevost vehicles to monitor tire pressure (TPMS system) are being replaced by new Huf sensors and their corresponding stainless valves stems. Since the older and newer sensors are using different valve stems, replacement of a defective sensor on older vehicles will require the use of a new kit number (valve stem and sensor assembly). The table below provides a quick overview between the older and newer part numbers depending on wheel application.
MI16-14
Use this procedure when a suspension height check or adjustment must be performed.
MI16-15A
The Beru sensors used on Prevost vehicles to monitor tire pressure (TPMS system) are being replaced by new Huf sensors and their corresponding stainless valves stems. Since the older and newer sensors are using different valve stems, replacement of a defective sensor on older vehicles will require the use of a new kit number (valve stem and sensor assembly). The table below provides a quick overview between the older and newer part numbers depending on wheel application.
Mi16-15
The Beru sensors used on Prevost vehicles to monitor tire pressure (TPMS system) are being replaced by new Huf sensors and their corresponding stainless valves stems. Since the older and newer sensors are using different valve stems, replacement of a defective sensor on older vehicles will require the use of a new kit number (valve stem and sensor assembly). The table below provides a quick overview between the older and newer part numbers depending on wheel application.
MI16-16
This procedure explains how to perform a STARTER REMOVAL AND INSTALLATION, and does apply to Melco 105P70 starter part number #21212425.
MI16-05
This Maintenance Information shares information about the Bendix M-32QR valve replaced by M-40QR model htat need to be taken into consideration, specially when switching them for the first time on a vehicle.
IS-13169A
This Instruction Sheet explains how to install the AWARE ADAPTIVE CRUISE BRAKING (ACB) FLR20 RADAR SENSOR REPLACEMENT kits # 145372 and 145373
Complaint counts are reports filed with NHTSA, not failure rates. A common model collects more of them than a rare one that breaks more often.