MI22-12B
Service Bulletin/Repair Instructions
Air Tanks Draining Sequence. Revision: B - General Update
Vehicle report
Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
MI22-12B
Air Tanks Draining Sequence. Revision: B - General Update
MI22-12A
Air Tanks Draining Sequence. Revision: A - Erroneous Secondary & Accessory tanks location.
MI22-12
Air Tanks Draining Sequence
IS-22902
TAG AXLE HUB FLANGE - ALTERNATE CAP SCREW
IS21-072
STEERING GATEWAY, revision A : Cancel watch dog removal from EFD part of the instruction
MI20-08C
STORAGE AND STARTUP GUIDELINES : part number updates
IS21-072A
STEERING GATEWAY Revision A Cancel watch dog removal from EFD part of the instruction
IS21-901
X3 SERIES ENVIROCARE - IONS AIR SANITIZER
IS20-925A
CENTRAL HVAC MERV FILTERS INSTALLATION
MI18-16B
BOSCH HD10 ALTERNATOR DIAGNOSTIC GUIDE Revision B To avoid replacement of alternators that are in fact in good working order, perform the steps which follow to help you perform a more precise diagnosis.
MI21-06
Diesel Exhaust Fluid ( DEF ) Contamination In Fuel System, Inspection And Repair â From US10 to newer engine generation
Mi21-07A
RONT & TAG AXLE â UNITIZED HUB BEARING END PLAY VERIFICATION AND REPLACEMENT
MI20-19A
Rev A: Mention added concerning DDC Series 60 engine SCA requirement
MI21-01
VOLVO I-SHIFT TRANSMISSION REPLACEMENT - DIFFERENCE BETWEEN CONNECTIONS AT THE TOP OF THE OIL FILTER HOUSING
MI20-19
INTRODUCING A NEW ENGINE COOLANT INTO SERVICE
MI20-12
JERKY, NOISY OR HARD TO TURN STEERING GEARBOX. HYDRAULIC END LIMITER ADJUSTMENT. All models â equipped with RB Bosch/ZF Servocom or Servocomtronic steering gearbox
MI20-08A
STORAGE AND STARTUP GUIDELINES: Rev A: 21516229 replaced by 23381562 20523393 replaced by 21454749 800383 removed 611471 replaced by 611360 70376808 replaced by 21036050 21396642 replaced by 20967831
MI20-09
PREVOST VEHICLE DISINFECTION PROCEDURE
MI20-08
STORAGE AND STARTUP GUIDELINES - ALL PREVOST VEHICLES & VOLVO 9700
MI15-24
Added: Power cables for L.H. side alternator & fan drive breaker box
NOX_Conv1
Repair instructions to address fault codes P207F-00 - Reductant Quality
NOx_Conv2
Repair instructions to address fault codes P207F-00; P20EE-00
IS-17905A
This instruction sheet explains how to install an ELD interface kit on Pre-OBD Prevost Vehicles equipped with Volvo D13 Engines
IS-18910
This instruction sheet explains how to install a flap over the diesel filling cap
IS-11003G
This Instruction sheet explains how to replace the ?MASTER ID? WITH ?MCM? Module
IS-13009D
This instruction sheet explains how to install and adjust drag link # 660699
IS-11003F
This Instruction sheet explains how to replace the "MASTER ID WITH MCM" Module
IS-13009C
This instruction sheet explains how to install and adjust drag link # 660699
IS12010
This instruction sheet explains how to replace the left bell crank using kit 161349
MI18-21A
This Maintenance Information presents information about the Bitzer A/C compressor oil change interval and reminds technicians to clean the oil filter/strainer and the magnetic drain plug.
IS-15003E
This insruction Sheet explains how to insall the Bosch HD10 24v-150a Alternator Conversion Kit ? Twin Bosch Mounted On Volvo D13 Engine
MI16-17G
This Maintenance Information explains how to remove and install the Bosch HD10 (120A or 150A) alternators
MI18-16A
This Maintenance Information presents guidelines to help with the diagnosis of the Bosch HD10 alternators
MI18-21
This Maintenance Information presents information about the Bitzer A/C compressor oil change interval and reminds technicians to clean the oil filter/strainer and the magnetic drain plug.
MI18-02
This Mainteannce Informaiton presents the latest engine oil & filter change intervals for the Volvo Engine
MI16-17F
This Maintenance Information explains how to remove and install the Bosch HD10 (120A or 150A) alternators
IS-17905
This instruction sheet explains how to install an ELD interface kit on Pre-OBD Prevost Vehicles equipped with Volvo D13 Engines
IS-13009B
This instruction sheet explains how to install and adjust drag link # 660699
SCI17-35
This internal instruction explains how to bench program the FMS gateway module used in the ELD (Electronic Logging Device) interface kit for pre-OBD13 vehicles.
MI17-22
This Maintenance Information explains how to inspect the Fuel Tank Cradle Mounting Screws on a yearly basis
CK17-27
This conversion kit explains how to to disable the ACB radar.
IS-11003E
This Instruction sheet explains how to remplace MASTER ID? WITH ?MCM? Module
IS-17901
This instructions sheet explains how to program a Wabco Smart Trac ABS ECU.
IS-15003D
This insruction Sheet explains how to insall the Bosch HD10 24v-150a Alternator Conversion Kit ? Twin Bosch Mounted On Volvo D13 Engine
IS-15003C
This instruction sheet explains how to use the Bosch HD10 24V-150A Alternator Conversion Kit
MI16-17E
This Maintenance Information explains how to remove and install the Bosch HD10 (120A or 150A) alternator.
IS-15003B
This instruction sheet explains how to use the Bosch HD10 24V-150A Alternator Conversion Kit
MI16-15B
The Beru sensors used on Prevost vehicles to monitor tire pressure (TPMS system) are being replaced by new Huf sensors and their corresponding stainless valves stems. Since the older and newer sensors are using different valve stems, replacement of a defective sensor on older vehicles will require the use of a new kit number (valve stem and sensor assembly). The table below provides a quick overview between the older and newer part numbers depending on wheel application.
IS-11003D
This Instruction sheet explains how to remplace MASTER ID? WITH ?MCM? MODULE
MI16-22
Use this maintenance information procedure to resolve an undesired behaviour on 2008-2012 vehicles. In sleep mode, certain marker lights may remain illuminated.
MI16-15A
The Beru sensors used on Prevost vehicles to monitor tire pressure (TPMS system) are being replaced by new Huf sensors and their corresponding stainless valves stems. Since the older and newer sensors are using different valve stems, replacement of a defective sensor on older vehicles will require the use of a new kit number (valve stem and sensor assembly). The table below provides a quick overview between the older and newer part numbers depending on wheel application.
Mi16-15
The Beru sensors used on Prevost vehicles to monitor tire pressure (TPMS system) are being replaced by new Huf sensors and their corresponding stainless valves stems. Since the older and newer sensors are using different valve stems, replacement of a defective sensor on older vehicles will require the use of a new kit number (valve stem and sensor assembly). The table below provides a quick overview between the older and newer part numbers depending on wheel application.
MI16-16
This procedure explains how to perform a STARTER REMOVAL AND INSTALLATION, and does apply to Melco 105P70 starter part number #21212425.
WB15-50
On the vehicles affected by this bulletin the rear junction box decal located in the right engine compartment is displaying incorrect information regarding the R34 relay voltage. Specifically, the R34 relay should be identified as a 24 volt relay instead of a 12 volt relay. Consequently, all affected vehicles must have a small decal displaying the correct information applied over the rear junction box decal R34 relay description.
IS-15907A
This Instruction Sheet explains how to assemble the BENDIX FLR10 AND FLR20 RADAR SENSOR ALIGNMENT TOOL
MI15-41
This Maintenance Information reminds Prevost customers that cleaning products designed for external washing of vehicles should be used for exterior vehicle wash and in particular, for the washing of polycarbonate taillights.
MI15-43
New aramid cord poly-v belts are now available to replace the polyester cord alternator belts previously used on Prevost vehicles equipped with Bosch HD10 alternators.
IS-11003A
This Instruction sheet explains how to replace MASTER ID? WITH ?MCM? MODULE
MI15-18
This Maintenance Information does explain how five year old vehicles and older should be subjected to a thorough structural inspection.
IS-15003A
This instruction sheet explains how to use the Bosch HD10 24V-150A Altenrator Conversion Kit
WB14-47B
On the vehicles affected by this bulletin, perform a software update of ECM (Engine Control Module) and ACM (Aftertreatment Control Module) to provide improved temperature-related behaviour. The software will also change urea dosing valve behavior at shutdown and key-on. As an additional improvement, replace the urea dosing valve by an improved design. These hardware and software improvements aim to reduce the occurrence of clogging and shorting of the Urea Dosing Valve.
IS-14130
This Instruction Sheet explains how to use Retrofit kit for obsoleted small AC condensers (950018 & 950335)
IS-13158
This Instruction Sheet explains how to install Keyless Keypad using either kit 069140 or 069141
WB14-32
On the vehicles affected by this bulletin, it is possible to observe signs of corrosion at the base of the master relay installed in the vehicle battery box. At the next service occasion, install a new relay along with shims between the relay mounting flange and the battery box bottom in a way that space is created between the relay base and the battery box bottom, preventing corrosion of the relay.
WB14-28E
On the vehicles affected by this bulletin, replace the LTD, relocate and replace the IR sensor as described in the following procedure.
SP14-05B
On the vehicles affected by this bulletin, perform a turbo replacement if fault codes 27 FMI 7 or SPN641 FMI 7 or P004607 (OBD13) are found. Bulletin affects D13H engines with serial number from 984581 up to 1026719, excluded.
WB13-65D
On the vehicles affected by this bulletin, software updates with enhancements are available for the multiplex system, for the EMS and aftertreatment control module (ACM). On all vehicles, perform a DPF Service Regeneration and Crystal Sublimation when programming is completed.
WB13-58
On the vehicles affected by this bulletin, change the flexible hose at the engine air intake
WB13-63A
On the vehicles affected by this bulletin, inspection and replacement of 70 amp circuit breakers in the rear electrical compartments is required.
MI1346
This Maintenance Information explains that on some post EPA 2010 vehicles, it is possible for the combined charging and starting system F81 fuse to blow unexpectedly. To avoid this situation, a 3 amp diode can be added to the corresponding 24CO circuit to prevent electrical back-flow to the fuse. The following procedure describes the steps to follow to perform this modification.
SP13-44
The light switch may operate incorrectly when doors are closed for vehicles affected by this bulletin. Corrective action is presented.
MI13-33
This Maintenance Information explains that polyester reinforced silicone hoses and elbowscan be repalced by aramid reinforced hoses and elbows for improved long term durability, and that constant torque hose clamps for silicone hoses with 5/8po, 3/4po, 7/8po, 1 1/8po and 1 3/8po inside diameter (I.D) can be replaced by new WAVE SEAL type constant torque hose clamps.
MI13-06
This Maintenance Information explains that hose clamps with a smaller diameter are available to increase the adjustment range at the upper and lower radiator flexible connections and at the oil cooler connections located under the turbocharger.
WB13-29
On the vehicles affected by this bulletin, a corrective measure is required due to bolts coming loose at the radiator fan clutch tripod attachment to the radiator. Addition of four (4) locknuts (jam nuts) will prevent bolts to loosen.
SP13-14
On the vehicles affected by this bulletin, inspection and replacement of 70 amp circuit breakers in the rear electrical compartments is required.
SP13-06
On affected vehicles the pipe clamps used to secure cooling system hoses located under the turbocharger may be misfitted, therefore this bulletin advises on how to proceed in order to changer with appropriate collars.
IS12050
This Instruction Sheet explains how to install kits to relocate the evaporator filters on existing Le Mirage XLII entertainer vehicles equipped with large A/C systems
SCI12-46A
This procedure will guide you through the steps required to relocate the evaporator filters on Le Mirage XL-II Entertainers. The heating coil in the evaporator compartment should be drained from coolant and some work and assembly is required on the filter box prior to carrying out the actual modification on the vehicle.
MI12-48
When performing the next periodic maintenance, check clearance between the 4-inch OD turbooutlet pipe (Prevost part number 052953) and a close support bracket. If evidence of rubbing isfound, i.e. scratched paint on the 4-inch OD turbo outlet pipe, a modification of the support bracket can be performed in order to increase the clearance between the involved components. The support bracket will remain strong enough for the duty even after being modified.
WB12-31B
On the vehicles affected by this bulletin, a new and improved dipstick is available for installation.
SP12-873
On the vehicles affected by this bulletin, update the multiplex programming at next service occasion, as there is a possibility that the tail lights turn on intermittently, and that a serie of codes appear in the dash.
IS11015B
This Instruction Sheet explains how to replace power relay p/n 561991 with improved power relay p/n 564218 and relay base p/n 564210
Complaint counts are reports filed with NHTSA, not failure rates. A common model collects more of them than a rare one that breaks more often.