MI22-12B
Service Bulletin/Repair Instructions
Air Tanks Draining Sequence. Revision: B - General Update
Vehicle report
2013 PREVOST WE
Service bulletins
98 bulletinsTechnical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
MI22-12A
Service Bulletin/Repair Instructions
Air Tanks Draining Sequence. Revision: A - Erroneous Secondary & Accessory tanks location.
MI22-12
Service Bulletin/Repair Instructions
Air Tanks Draining Sequence
IS-22902
Service Bulletin/Repair Instructions
TAG AXLE HUB FLANGE - ALTERNATE CAP SCREW
IS21-072
Service Bulletin/Repair Instructions
STEERING GATEWAY, revision A : Cancel watch dog removal from EFD part of the instruction
MI20-08C
Service Bulletin/Repair Instructions
STORAGE AND STARTUP GUIDELINES : part number updates
IS21-072A
Service Bulletin/Repair Instructions
STEERING GATEWAY Revision A Cancel watch dog removal from EFD part of the instruction
IS21-901
Service Bulletin/Repair Instructions
X3 SERIES ENVIROCARE - IONS AIR SANITIZER
IS20-925A
Service Bulletin/Repair Instructions
CENTRAL HVAC MERV FILTERS INSTALLATION
MI18-16B
Service Bulletin/Repair Instructions
BOSCH HD10 ALTERNATOR DIAGNOSTIC GUIDE Revision B To avoid replacement of alternators that are in fact in good working order, perform the steps which follow to help you perform a more precise diagnosis.
MI21-06
Service Bulletin/Repair Instructions
Diesel Exhaust Fluid ( DEF ) Contamination In Fuel System, Inspection And Repair â From US10 to newer engine generation
MI20-19A
Service Bulletin/Repair Instructions
Rev A: Mention added concerning DDC Series 60 engine SCA requirement
MI21-01
Service Bulletin/Repair Instructions
VOLVO I-SHIFT TRANSMISSION REPLACEMENT - DIFFERENCE BETWEEN CONNECTIONS AT THE TOP OF THE OIL FILTER HOUSING
MI20-19
Service Bulletin/Repair Instructions
INTRODUCING A NEW ENGINE COOLANT INTO SERVICE
MI20-12
Service Bulletin/Repair Instructions
JERKY, NOISY OR HARD TO TURN STEERING GEARBOX. HYDRAULIC END LIMITER ADJUSTMENT. All models â equipped with RB Bosch/ZF Servocom or Servocomtronic steering gearbox
MI20-08A
Service Bulletin/Repair Instructions
STORAGE AND STARTUP GUIDELINES: Rev A: 21516229 replaced by 23381562 20523393 replaced by 21454749 800383 removed 611471 replaced by 611360 70376808 replaced by 21036050 21396642 replaced by 20967831
MI20-09
Service Bulletin/Repair Instructions
PREVOST VEHICLE DISINFECTION PROCEDURE
MI20-08
Service Bulletin/Repair Instructions
STORAGE AND STARTUP GUIDELINES - ALL PREVOST VEHICLES & VOLVO 9700
MI15-24
Service Bulletin/Repair Instructions
Added: Power cables for L.H. side alternator & fan drive breaker box
FUELFILTER
Service Bulletin/Repair Instructions
Repair instructions to address fault codes P008A-00; P0087-00
NOX_Conv1
Service Bulletin/Repair Instructions
Repair instructions to address fault codes P207F-00 - Reductant Quality
NOx_Conv2
Service Bulletin/Repair Instructions
Repair instructions to address fault codes P207F-00; P20EE-00
IS-17905A
Service Bulletin/Repair Instructions
This instruction sheet explains how to install an ELD interface kit on Pre-OBD Prevost Vehicles equipped with Volvo D13 Engines
IS-17071A
Service Bulletin/Repair Instructions
This instruction sheet explains how to install an ELD interface on OBD vehicles
IS-18910
Service Bulletin/Repair Instructions
This instruction sheet explains how to install a flap over the diesel filling cap
IS-13009D
Service Bulletin/Repair Instructions
This instruction sheet explains how to install and adjust drag link # 660699
IS-13009C
Service Bulletin/Repair Instructions
This instruction sheet explains how to install and adjust drag link # 660699
IS12010
Service Bulletin/Repair Instructions
This instruction sheet explains how to replace the left bell crank using kit 161349
MI18-21A
Service Bulletin/Repair Instructions
This Maintenance Information presents information about the Bitzer A/C compressor oil change interval and reminds technicians to clean the oil filter/strainer and the magnetic drain plug.
IS-15003E
Service Bulletin/Repair Instructions
This insruction Sheet explains how to insall the Bosch HD10 24v-150a Alternator Conversion Kit ? Twin Bosch Mounted On Volvo D13 Engine
MI16-17G
Service Bulletin/Repair Instructions
This Maintenance Information explains how to remove and install the Bosch HD10 (120A or 150A) alternators
MI18-16A
Service Bulletin/Repair Instructions
This Maintenance Information presents guidelines to help with the diagnosis of the Bosch HD10 alternators
MI18-21
Service Bulletin/Repair Instructions
This Maintenance Information presents information about the Bitzer A/C compressor oil change interval and reminds technicians to clean the oil filter/strainer and the magnetic drain plug.
MI18-02
Service Bulletin/Repair Instructions
This Mainteannce Informaiton presents the latest engine oil & filter change intervals for the Volvo Engine
MI16-17F
Service Bulletin/Repair Instructions
This Maintenance Information explains how to remove and install the Bosch HD10 (120A or 150A) alternators
WB15-19H
Service Bulletin/Repair Instructions
This bulletin explains how to add a reinforcement bracket to Bitzer A/C compressor to increase the installation stiffness and reduce vibration amplitude.
IS-17905
Service Bulletin/Repair Instructions
This instruction sheet explains how to install an ELD interface kit on Pre-OBD Prevost Vehicles equipped with Volvo D13 Engines
IS-13009B
Service Bulletin/Repair Instructions
This instruction sheet explains how to install and adjust drag link # 660699
SCI17-35
Service Bulletin/Repair Instructions
This internal instruction explains how to bench program the FMS gateway module used in the ELD (Electronic Logging Device) interface kit for pre-OBD13 vehicles.
MI17-22
Service Bulletin/Repair Instructions
This Maintenance Information explains how to inspect the Fuel Tank Cradle Mounting Screws on a yearly basis
IS-17071
Service Bulletin/Repair Instructions
This instruction sheet explains how to install an ELD interface on OBD vehicles
IS-17907
Service Bulletin/Repair Instructions
This instruction sheet explains how to install the Volvo Electronic Logging Device (ELD)
CK17-27
Service Bulletin/Repair Instructions
This conversion kit explains how to to disable the ACB radar.
IS-15003D
Service Bulletin/Repair Instructions
This insruction Sheet explains how to insall the Bosch HD10 24v-150a Alternator Conversion Kit ? Twin Bosch Mounted On Volvo D13 Engine
IS-15003C
Service Bulletin/Repair Instructions
This instruction sheet explains how to use the Bosch HD10 24V-150A Alternator Conversion Kit
MI16-17E
Service Bulletin/Repair Instructions
This Maintenance Information explains how to remove and install the Bosch HD10 (120A or 150A) alternator.
IS-15003B
Service Bulletin/Repair Instructions
This instruction sheet explains how to use the Bosch HD10 24V-150A Alternator Conversion Kit
MI16-15B
Service Bulletin/Repair Instructions
The Beru sensors used on Prevost vehicles to monitor tire pressure (TPMS system) are being replaced by new Huf sensors and their corresponding stainless valves stems. Since the older and newer sensors are using different valve stems, replacement of a defective sensor on older vehicles will require the use of a new kit number (valve stem and sensor assembly). The table below provides a quick overview between the older and newer part numbers depending on wheel application.
MI16-15A
Service Bulletin/Repair Instructions
The Beru sensors used on Prevost vehicles to monitor tire pressure (TPMS system) are being replaced by new Huf sensors and their corresponding stainless valves stems. Since the older and newer sensors are using different valve stems, replacement of a defective sensor on older vehicles will require the use of a new kit number (valve stem and sensor assembly). The table below provides a quick overview between the older and newer part numbers depending on wheel application.
Wb15-19F
Service Bulletin/Repair Instructions
On the vehicles affected by this bulletin, vibration is causing damage to A/C compressor and compressor harness connectors. Addition of a reinforcement bracket to Bitzer A/C compressor is needed to increase the installation stiffness and reduce vibration amplitude.
Mi16-15
Service Bulletin/Repair Instructions
The Beru sensors used on Prevost vehicles to monitor tire pressure (TPMS system) are being replaced by new Huf sensors and their corresponding stainless valves stems. Since the older and newer sensors are using different valve stems, replacement of a defective sensor on older vehicles will require the use of a new kit number (valve stem and sensor assembly). The table below provides a quick overview between the older and newer part numbers depending on wheel application.
MI16-16
Service Bulletin/Repair Instructions
This procedure explains how to perform a STARTER REMOVAL AND INSTALLATION, and does apply to Melco 105P70 starter part number #21212425.
MI16-05
Service Bulletin/Repair Instructions
This Maintenance Information shares information about the Bendix M-32QR valve replaced by M-40QR model htat need to be taken into consideration, specially when switching them for the first time on a vehicle.
WB15-19E
Service Bulletin/Repair Instructions
On the vehicles affected by this bulletin, vibration is causing damage to A/C compressor and compressor harness connectors. Addition of a reinforcement bracket to Bitzer A/C compressor is needed to increase the installation stiffness and reduce vibration amplitude.
WB15-50
Service Bulletin/Repair Instructions
On the vehicles affected by this bulletin the rear junction box decal located in the right engine compartment is displaying incorrect information regarding the R34 relay voltage. Specifically, the R34 relay should be identified as a 24 volt relay instead of a 12 volt relay. Consequently, all affected vehicles must have a small decal displaying the correct information applied over the rear junction box decal R34 relay description.
IS-15907A
Service Bulletin/Repair Instructions
This Instruction Sheet explains how to assemble the BENDIX FLR10 AND FLR20 RADAR SENSOR ALIGNMENT TOOL
MI15-41
Service Bulletin/Repair Instructions
This Maintenance Information reminds Prevost customers that cleaning products designed for external washing of vehicles should be used for exterior vehicle wash and in particular, for the washing of polycarbonate taillights.
MI15-43
Service Bulletin/Repair Instructions
New aramid cord poly-v belts are now available to replace the polyester cord alternator belts previously used on Prevost vehicles equipped with Bosch HD10 alternators.
WB15-44A
Service Bulletin/Repair Instructions
On the vehicles affected by this bulletin, the equipment used to tighten the wheel lugs in a visit to one of our Service Center between November 2014 and June 2015, was found to be out of specification, possibly delivering a torque value inferior to the specified 450 to 500 ft-lb (610 to 680 Nm). Please verify and correct as necessary the wheel lug torque on the concerned vehicles, or bring the vehicle at a Prevost Service Center for verification at your earliest convenience.
WB15-19
Service Bulletin/Repair Instructions
On the vehicles affected by this bulletin, vibration is causing damage to A/C compressor and compressor harness connectors. Addition of a reinforcement bracket to Bitzer A/C compressor is needed to increase the installation stiffness and reduce vibration amplitude.
MI15-18
Service Bulletin/Repair Instructions
This Maintenance Information does explain how five year old vehicles and older should be subjected to a thorough structural inspection.
IS-15003A
Service Bulletin/Repair Instructions
This instruction sheet explains how to use the Bosch HD10 24V-150A Altenrator Conversion Kit
WB14-47B
Service Bulletin/Repair Instructions
On the vehicles affected by this bulletin, perform a software update of ECM (Engine Control Module) and ACM (Aftertreatment Control Module) to provide improved temperature-related behaviour. The software will also change urea dosing valve behavior at shutdown and key-on. As an additional improvement, replace the urea dosing valve by an improved design. These hardware and software improvements aim to reduce the occurrence of clogging and shorting of the Urea Dosing Valve.
IS-14130
Service Bulletin/Repair Instructions
This Instruction Sheet explains how to use Retrofit kit for obsoleted small AC condensers (950018 & 950335)
WB14-45C
Service Bulletin/Repair Instructions
On the vehicles affected by this bulletin remove the ACM relay and base identified R49. Reconnect the 24V power wire and protect the remaining signal wires with shrink tube.
SP14-46
Service Bulletin/Repair Instructions
This bulletin is performed on a fix as fail basis. On the vehicles affected by this bulletin, update to the latest configuration of wiring and sensors for the Bitzer compressor.
IS-13158
Service Bulletin/Repair Instructions
This Instruction Sheet explains how to install Keyless Keypad using either kit 069140 or 069141
WB14-32
Service Bulletin/Repair Instructions
On the vehicles affected by this bulletin, it is possible to observe signs of corrosion at the base of the master relay installed in the vehicle battery box. At the next service occasion, install a new relay along with shims between the relay mounting flange and the battery box bottom in a way that space is created between the relay base and the battery box bottom, preventing corrosion of the relay.
WB14-42A
Service Bulletin/Repair Instructions
On the vehicles affected by this bulletin, perform a power source improvement and a multiplex software update for the steering Gateway module. On a limited number of vehicles, the module will be replaced with the latest version of the part.
WB14-08C
Service Bulletin/Repair Instructions
On the vehicles affected by this bulletin, verify the revision numbers of the steering wheel gateway module and multiplex software. If applicable, replace with the latest version. A power source improvement is also required. On some vehicles, as a temporary measure, a switch was installed on the left dashboard for cruise control SET and RESUME. This installation must be removed to restore these controls to the steering wheel.
SP13-95
Service Bulletin/Repair Instructions
On the vehicles affected by this special bulletin, replace the rear tripod member.
WB14-06G
Service Bulletin/Repair Instructions
On the vehicles affected by this bulletin, perform the following verifications and modifications on the A/C system: Bulletin is divided in five steps, refer to detailed instructions below. STEP 1: Unloader replacement (Step moved to Warranty Bulletin WB15-19) STEP 2: System vacuum, wiring update, remote pressure transducer and switch installation. STEP 3: Seal the evaporator compartment ventilation discharge duct. STEP 4: Check Evaporator expansion valve bulb position and MUX software version. STEP 5: Dynamic A/C system test to confirm all functions operate correctly.
WB14-28E
Service Bulletin/Repair Instructions
On the vehicles affected by this bulletin, replace the LTD, relocate and replace the IR sensor as described in the following procedure.
SP14-05B
Service Bulletin/Repair Instructions
On the vehicles affected by this bulletin, perform a turbo replacement if fault codes 27 FMI 7 or SPN641 FMI 7 or P004607 (OBD13) are found. Bulletin affects D13H engines with serial number from 984581 up to 1026719, excluded.
WB13-65D
Service Bulletin/Repair Instructions
On the vehicles affected by this bulletin, software updates with enhancements are available for the multiplex system, for the EMS and aftertreatment control module (ACM). On all vehicles, perform a DPF Service Regeneration and Crystal Sublimation when programming is completed.
WB13-58
Service Bulletin/Repair Instructions
On the vehicles affected by this bulletin, change the flexible hose at the engine air intake
SP13-69
Service Bulletin/Repair Instructions
Possible air return between evaporator air conduit and compartment. No airtightness between duct and floor / floor structure. Bulletin to describe how to add a sealing joint for better air tightness.
WB13-63A
Service Bulletin/Repair Instructions
On the vehicles affected by this bulletin, inspection and replacement of 70 amp circuit breakers in the rear electrical compartments is required.
WB13-56
Service Bulletin/Repair Instructions
On the vehicles affected by this bulletin, the air dryer assembly may present a leak at the pressure probe connection. The O-ring in this location may be deformed due to the fitting arrangement. Adding a metal ring will prevent this issue.
WB13-55A
Service Bulletin/Repair Instructions
On the vehicles affected by this bulletin, the upper support of the tripod fan support must be inspected for the presence of weld. If no weld is found, it must be replaced.
SP13-57
Service Bulletin/Repair Instructions
The ventilation duct on the rear electrical box may not be closed properly on vehicles affected by this bulletin
WB13-49
Service Bulletin/Repair Instructions
On the vehicles affected by this bulletin, replace the prototype version of the Urea Quality Sensor #21891229 by the production version of the sensor #22073036.
MI1346
Service Bulletin/Repair Instructions
This Maintenance Information explains that on some post EPA 2010 vehicles, it is possible for the combined charging and starting system F81 fuse to blow unexpectedly. To avoid this situation, a 3 amp diode can be added to the corresponding 24CO circuit to prevent electrical back-flow to the fuse. The following procedure describes the steps to follow to perform this modification.
SP13-44
Service Bulletin/Repair Instructions
The light switch may operate incorrectly when doors are closed for vehicles affected by this bulletin. Corrective action is presented.
MI13-33
Service Bulletin/Repair Instructions
This Maintenance Information explains that polyester reinforced silicone hoses and elbowscan be repalced by aramid reinforced hoses and elbows for improved long term durability, and that constant torque hose clamps for silicone hoses with 5/8po, 3/4po, 7/8po, 1 1/8po and 1 3/8po inside diameter (I.D) can be replaced by new WAVE SEAL type constant torque hose clamps.
SP13-39
Service Bulletin/Repair Instructions
On the vehicles affected by this bulletin, the spot welded hex nut that holds the battery box cover retaining rod may break loose. Follow the procedure described below to repair vehicles.
SP13-41
Service Bulletin/Repair Instructions
Check that the pantograph arm does not interfere with gas spring in "door closed" position.
SP13-40
Service Bulletin/Repair Instructions
The door may unlock and open in normal operating conditions. The rod that operates the mechanism is too short.
MI13-06
Service Bulletin/Repair Instructions
This Maintenance Information explains that hose clamps with a smaller diameter are available to increase the adjustment range at the upper and lower radiator flexible connections and at the oil cooler connections located under the turbocharger.
WB13-29
Service Bulletin/Repair Instructions
On the vehicles affected by this bulletin, a corrective measure is required due to bolts coming loose at the radiator fan clutch tripod attachment to the radiator. Addition of four (4) locknuts (jam nuts) will prevent bolts to loosen.
WB13-32B
Service Bulletin/Repair Instructions
On the vehicles affected by this bulletin, the NOx sensor must be replaced and the EMS software requires an update. This must be done to allow correct emissions inspection in particular states including California.
SP13-22
Service Bulletin/Repair Instructions
Radius rod support weld inspection: weld beads may be too small on radius rod supports on rear sub-frame.
SP13-20
Service Bulletin/Repair Instructions
On the vehicles affected by this bulletin, make sure that the vertical posts #22177 between baggage compartment are not contaminated by rush (traces, corrosion pin-holes).
SP13-19A
Service Bulletin/Repair Instructions
Grille frame gluing verification on the DPF door (left side, over the radiator door). If part shows no sign of separation or ungluing, it is ok. If testing reveals poor bonding, remove grille, glue and double face tape.
IS12050
Service Bulletin/Repair Instructions
This Instruction Sheet explains how to install kits to relocate the evaporator filters on existing Le Mirage XLII entertainer vehicles equipped with large A/C systems
MI12-48
Service Bulletin/Repair Instructions
When performing the next periodic maintenance, check clearance between the 4-inch OD turbooutlet pipe (Prevost part number 052953) and a close support bracket. If evidence of rubbing isfound, i.e. scratched paint on the 4-inch OD turbo outlet pipe, a modification of the support bracket can be performed in order to increase the clearance between the involved components. The support bracket will remain strong enough for the duty even after being modified.
WB12-31B
Service Bulletin/Repair Instructions
On the vehicles affected by this bulletin, a new and improved dipstick is available for installation.
IS11015B
Service Bulletin/Repair Instructions
This Instruction Sheet explains how to replace power relay p/n 561991 with improved power relay p/n 564218 and relay base p/n 564210
Reading this report
Complaint counts are reports filed with NHTSA, not failure rates. A common model collects more of them than a rare one that breaks more often.