Vehicle report
Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
MI26-00
The gasket thickness was increased from 1.5 mm to 3 mm to prevent interference between the collar ends, which previously made it impossible to reach the specified tightening torque. Increasing the gasket thickness ensures sufficient clearance between the collar ends and thus guarantees optimal tightening.
IS-23019A
Sway bar collars improvement. Revision A : Add front sway bar support replacement and change bolts lenght.
IS-23019
SWAY BAR COLLARS IMPROVEMENT
IS-21072B
STEERING GATEWAY. Revision B - PIN 2 and 10 were inverted on connector A139
MI22-12B
Air Tanks Draining Sequence. Revision: B - General Update
MI22-12A
Air Tanks Draining Sequence. Revision: A - Erroneous Secondary & Accessory tanks location.
MI22-12
Air Tanks Draining Sequence
IS-17151C
Halogen to LED fog light replacement kit. Revision: C - Advanced kits canceled
MI20-08C
STORAGE AND STARTUP GUIDELINES : part number updates
IS20-925A
CENTRAL HVAC MERV FILTERS INSTALLATION
IS-08080B
Sound Selector replacement, VSS04 to VSS05; When replacing a vehicle sound selector model VSS04 with a new sound selector model VSS05, an interface harness is required to connect the vehicle harness to the new sound selector model and a new VSS05 compatible radio unit must also be installed. This procedure describes the steps required to perform this update.
IS-20925A
CENTRAL HVAC MERV FILTERS INSTALLATION REVA
IS-18091A
TIE ROD 610052 FIRST INSTALLATION INSTRUCTIONS: Use these instructions when replacing the drop joint tie rod on S82, S84 / S84U I-beam axles. The new tie rod will be adjusted to the length of the original; however, a steering alignment needs to be performed after replacement.
MI20-19B
INTRODUCING A NEW ENGINE COOLANT INTO PREVOST SERVICE CENTER NETWORK
MI20-19A
Rev A: Mention added concerning DDC Series 60 engine SCA requirement
MI20-19
INTRODUCING A NEW ENGINE COOLANT INTO SERVICE
SCi20-16
FAN CLUTCH PLATE BOLTS RE-TORQUING
MI20-08B
STORAGE AND STARTUP GUIDELINES Revision: B Parts added to Suggested Material 08-10-2020
MI20-12
JERKY, NOISY OR HARD TO TURN STEERING GEARBOX. HYDRAULIC END LIMITER ADJUSTMENT. All models â equipped with RB Bosch/ZF Servocom or Servocomtronic steering gearbox
MI20-08A
STORAGE AND STARTUP GUIDELINES: Rev A: 21516229 replaced by 23381562 20523393 replaced by 21454749 800383 removed 611471 replaced by 611360 70376808 replaced by 21036050 21396642 replaced by 20967831
IS-20907
Plexiglass Panel Behind Driver X3
IS-20905
HAND SANITIZER DISPENSER INSTALLATION
MI20-09
PREVOST VEHICLE DISINFECTION PROCEDURE
MI20-08
STORAGE AND STARTUP GUIDELINES - ALL PREVOST VEHICLES & VOLVO 9700
MI15-24
Added: Power cables for L.H. side alternator & fan drive breaker box
IS-19923A
Revision : Addition of Wiring Schematics at the end of this document
SCI19-30
The intent of this procedure is to guide you through the steps required to program a MCM especially for the control of the HVAC module as described in instruction sheets IS-19923.
IS-19092
This instruction sheet explains how to install 780428 door actuator replacement.
IS-19915
MP-1000 MULTIMEDIA PLAYER INSTALLATION
MI18-45A
Vehicles identified below are compatible with a new tie rod design. This new tie rod 610052 has updated ball joints and a fine adjuster sleeve. It replaces former drop type ball joint tie rods. Refer to IS-18091 for installation instructions. This document details maintenance inspection and toe-in adjustment with the new design tie rod.
IS-19040
POWER STEERING PUMP DISCHARGE HOSE (PRESSURE) REPLACEMENT
MI15-56
On vehicles mentioned above, should the curbside electric sunshade fail to operate without encountering a drive mechanism issue, perform the following procedure.
MI11-27
PREVOST: 12" BRUSHLESS CONDENSER FAN REPLACEMENT. MODELS INCLUDE XLII MTH, AND H3VIP MTH. MODEL YEARS ARE 2008-2011. *KB
SCI09-28
PREVOST: INSTALLING THREE-POINT PASSENGER SEAT RESTRAINT SYSTEM. THE PURPOSE OF THE FOLLOWING PROCEDURE IS TO FACILITATE THE JOB AND TO HELP IDENTIFY THE DIFFICULT AREAS. ALSO INCLUDED MODELS HE-41 AND HE-45 COACHES MODEL YEARS 1998-2008; MODEL XLII AND X3-45 COACHES MODEL YEARS 1998-2008. *JS
WB09-17A
PREVOST: INSPECTION OF WELD BEADS ON 85' SUPER CARGO DOOR PANTOGRAPH ARM. IF BEADS ARE MISSING COULD CAUSE FATIGUE OR CRACKING. MODELS X3-45 COACHES. MODEL YEAR 2007-2008. *JS
MI08-04
FRONT AND TAG AXLE HUB BEARING AND KING PIN PERIODIC MAINTENANCE. BEARINGS MUST BE INSPECTED AT INTERVALS OF 30,000 MILES (48 000KM). KING PINS SHOULD BE SERVICED EVERY 6, 250 MILES (10,000 KM) OR TWICE A YEAR. ALSO INCLUDED MODEL VIP-45 MTH MODEL YEARS 2004-2008. MODEL XLII MTH MODEL YEARS 2004-2008. *JS
WB08-02A
POWER WINDOW HARNESS- REMOVAL OF ZENER SUPPRESSOR DIODES. A FAULTY DIODE WILL CAUSE THE BURNING OF THE FUSE PROTECTING THE CIRCUIT. ALSO INCLUDED MODEL XLII-40, XLII-45 MOTORHOMES & ENTERTAINER XLII-45. MODEL YEARS 2007-2008. MODEL VIP MOTORHOMES. MODEL YEARS 2006-2007. *JS
0701
RETAINING RING INSTALLATION ONTO FRONT SUSPENSION SWAY BAR. *KB
Complaint counts are reports filed with NHTSA, not failure rates. A common model collects more of them than a rare one that breaks more often.