Vehicle report

2010 PREVOST X3

Compare every PREVOST X3 yearNHTSA and EPA records

Service bulletins

100 bulletins

Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.

MI16-32

Service Bulletin/Repair Instructions

Improved bearings are now available to replace the original bearings used on some Prevost vehicles idler pulleys.

IS-21072B

Service Bulletin/Repair Instructions

STEERING GATEWAY. Revision B - PIN 2 and 10 were inverted on connector A139

MI22-12B

Service Bulletin/Repair Instructions

Air Tanks Draining Sequence. Revision: B - General Update

MI22-12A

Service Bulletin/Repair Instructions

Air Tanks Draining Sequence. Revision: A - Erroneous Secondary & Accessory tanks location.

MI22-12

Service Bulletin/Repair Instructions

Air Tanks Draining Sequence

IS-17151C

Service Bulletin/Repair Instructions

Halogen to LED fog light replacement kit. Revision: C - Advanced kits canceled

IS-22902

Service Bulletin/Repair Instructions

TAG AXLE HUB FLANGE - ALTERNATE CAP SCREW

MI20-08C

Service Bulletin/Repair Instructions

STORAGE AND STARTUP GUIDELINES : part number updates

IS21-072A

Service Bulletin/Repair Instructions

STEERING GATEWAY Revision A Cancel watch dog removal from EFD part of the instruction

IS21-901

Service Bulletin/Repair Instructions

X3 SERIES ENVIROCARE - IONS AIR SANITIZER

IS20-925A

Service Bulletin/Repair Instructions

CENTRAL HVAC MERV FILTERS INSTALLATION

MI18-16B

Service Bulletin/Repair Instructions

BOSCH HD10 ALTERNATOR DIAGNOSTIC GUIDE Revision B To avoid replacement of alternators that are in fact in good working order, perform the steps which follow to help you perform a more precise diagnosis.

MI21-06

Service Bulletin/Repair Instructions

Diesel Exhaust Fluid ( DEF ) Contamination In Fuel System, Inspection And Repair – From US10 to newer engine generation

Mi21-07A

Service Bulletin/Repair Instructions

RONT & TAG AXLE – UNITIZED HUB BEARING END PLAY VERIFICATION AND REPLACEMENT

IS-20925A

Service Bulletin/Repair Instructions

CENTRAL HVAC MERV FILTERS INSTALLATION REVA

IS-18091A

Service Bulletin/Repair Instructions

TIE ROD 610052 FIRST INSTALLATION INSTRUCTIONS: Use these instructions when replacing the drop joint tie rod on S82, S84 / S84U I-beam axles. The new tie rod will be adjusted to the length of the original; however, a steering alignment needs to be performed after replacement.

MI20-19B

Service Bulletin/Repair Instructions

INTRODUCING A NEW ENGINE COOLANT INTO PREVOST SERVICE CENTER NETWORK

MI20-19A

Service Bulletin/Repair Instructions

Rev A: Mention added concerning DDC Series 60 engine SCA requirement

MI20-19

Service Bulletin/Repair Instructions

INTRODUCING A NEW ENGINE COOLANT INTO SERVICE

IS-20922

Service Bulletin/Repair Instructions

SIGMA PASSENGER SEATS PARTITION KIT

MI20-08B

Service Bulletin/Repair Instructions

STORAGE AND STARTUP GUIDELINES Revision: B Parts added to Suggested Material 08-10-2020

MI20-12

Service Bulletin/Repair Instructions

JERKY, NOISY OR HARD TO TURN STEERING GEARBOX. HYDRAULIC END LIMITER ADJUSTMENT. All models – equipped with RB Bosch/ZF Servocom or Servocomtronic steering gearbox

MI20-08A

Service Bulletin/Repair Instructions

STORAGE AND STARTUP GUIDELINES: Rev A: 21516229 replaced by 23381562 20523393 replaced by 21454749 800383 removed 611471 replaced by 611360 70376808 replaced by 21036050 21396642 replaced by 20967831

MI20-09

Service Bulletin/Repair Instructions

PREVOST VEHICLE DISINFECTION PROCEDURE

MI20-08

Service Bulletin/Repair Instructions

STORAGE AND STARTUP GUIDELINES - ALL PREVOST VEHICLES & VOLVO 9700

MI15-24

Service Bulletin/Repair Instructions

Added: Power cables for L.H. side alternator & fan drive breaker box

IS-17151

Service Bulletin/Repair Instructions

THIS INSTRUCTION SHEET EXPLAINS HOW TO REPLACE HALOGEN FOG LIGHT TO LED'S

IS-18091

Service Bulletin/Repair Instructions

This Instruction Sheet explains how to perform the first installation of Tie Rod 610052 on Prevost vehicles equipped with Dana S82, S84 / S84U I-beam axles, 1994- today

IS-19915

Service Bulletin/Repair Instructions

MP-1000 MULTIMEDIA PLAYER INSTALLATION

IS-17910A

Service Bulletin/Repair Instructions

MESSAGE CENTER DISPLAY (MCD) REPLACEMENT

IS-17905A

Service Bulletin/Repair Instructions

This instruction sheet explains how to install an ELD interface kit on Pre-OBD Prevost Vehicles equipped with Volvo D13 Engines

IS-11003G

Service Bulletin/Repair Instructions

This Instruction sheet explains how to replace the ?MASTER ID? WITH ?MCM? Module

IS-13009D

Service Bulletin/Repair Instructions

This instruction sheet explains how to install and adjust drag link # 660699

SP18-13F

Service Bulletin/Repair Instructions

On the vehicles affected by this bulletin, proceed to the replacement of the drag link.

IS-18909

Service Bulletin/Repair Instructions

This instruction sheet explains how to replace the Carrier AC compressor with a Bitzer

IS-11003F

Service Bulletin/Repair Instructions

This Instruction sheet explains how to replace the "MASTER ID WITH MCM" Module

SCI18-46

Service Bulletin/Repair Instructions

This Service Center Instructions explains how to install the Prevost Ultimate Entertainment System

IS-13009C

Service Bulletin/Repair Instructions

This instruction sheet explains how to install and adjust drag link # 660699

IS-18907

Service Bulletin/Repair Instructions

This instruction sheet explains how to install hatches with fan on X3 vehicles.

IS-17910

Service Bulletin/Repair Instructions

This instruction sheet explains how to replace the message center display (MCD)

IS12010

Service Bulletin/Repair Instructions

This instruction sheet explains how to replace the left bell crank using kit 161349

IS-15003E

Service Bulletin/Repair Instructions

This insruction Sheet explains how to insall the Bosch HD10 24v-150a Alternator Conversion Kit ? Twin Bosch Mounted On Volvo D13 Engine

MI16-17G

Service Bulletin/Repair Instructions

This Maintenance Information explains how to remove and install the Bosch HD10 (120A or 150A) alternators

MI16-08B

Service Bulletin/Repair Instructions

This Maintenance Information presentes the new method of locking the electromagnetic clutch in the event of a failure. These new electromagnetic clutches will feature locking tabs in replacement of the locking bolts.

MI18-16A

Service Bulletin/Repair Instructions

This Maintenance Information presents guidelines to help with the diagnosis of the Bosch HD10 alternators

MI18-05

Service Bulletin/Repair Instructions

This maintenance information explains how to install valve assembly 130009 in replacement of valve 641274

MI16-17F

Service Bulletin/Repair Instructions

This Maintenance Information explains how to remove and install the Bosch HD10 (120A or 150A) alternators

SP18-13E

Service Bulletin/Repair Instructions

On the vehicles affected by this bulletin, replace the drag link.

IS-17905

Service Bulletin/Repair Instructions

This instruction sheet explains how to install an ELD interface kit on Pre-OBD Prevost Vehicles equipped with Volvo D13 Engines

SP18-13D

Service Bulletin/Repair Instructions

On the vehicles affected by this bulletin, proceed to the replacement of the drag link.

IS-13009B

Service Bulletin/Repair Instructions

This instruction sheet explains how to install and adjust drag link # 660699

wb17-16

Service Bulletin/Repair Instructions

On the vehicles affected by this bulletin, remove selected wires from C15 and C58 of the HVAC system wiring, and place them in new connectors C15B and C58B. New connectors have a higher amp rating. We recommend inspecting connectors C15 & C58 for heat damage before ordering parts. Depending on connector condition, order additional parts along with main kit. See Additional Parts table.

SCI17-35

Service Bulletin/Repair Instructions

This internal instruction explains how to bench program the FMS gateway module used in the ELD (Electronic Logging Device) interface kit for pre-OBD13 vehicles.

IS-17907

Service Bulletin/Repair Instructions

This instruction sheet explains how to install the Volvo Electronic Logging Device (ELD)

CK17-19A

Service Bulletin/Repair Instructions

This conversion kit explains how to remove TGW1 from vehicles using Tech Tool, no manual VDA changes needed. This conversion kit will work for any vehicle equipped with TGW1 up to the VIN's listed on the bulletin.

IS-11003E

Service Bulletin/Repair Instructions

This Instruction sheet explains how to remplace MASTER ID? WITH ?MCM? Module

IS-17901

Service Bulletin/Repair Instructions

This instructions sheet explains how to program a Wabco Smart Trac ABS ECU.

IS-15003D

Service Bulletin/Repair Instructions

This insruction Sheet explains how to insall the Bosch HD10 24v-150a Alternator Conversion Kit ? Twin Bosch Mounted On Volvo D13 Engine

IS-16100

Service Bulletin/Repair Instructions

This instruction sheet explains how to install latest radio models

IS-15003C

Service Bulletin/Repair Instructions

This instruction sheet explains how to use the Bosch HD10 24V-150A Alternator Conversion Kit

MI16-17E

Service Bulletin/Repair Instructions

This Maintenance Information explains how to remove and install the Bosch HD10 (120A or 150A) alternator.

MI16-08

Service Bulletin/Repair Instructions

On receiving your Kit Masters fan clutch you may notice a new method of locking the electromagnetic clutch in the event of a failure. These new electromagnetic clutches will feature locking tabs in replacement of the locking bolts. Applies to part number 550965; 550966 &550974.

IS-15003B

Service Bulletin/Repair Instructions

This instruction sheet explains how to use the Bosch HD10 24V-150A Alternator Conversion Kit

MI16-15B

Service Bulletin/Repair Instructions

The Beru sensors used on Prevost vehicles to monitor tire pressure (TPMS system) are being replaced by new Huf sensors and their corresponding stainless valves stems. Since the older and newer sensors are using different valve stems, replacement of a defective sensor on older vehicles will require the use of a new kit number (valve stem and sensor assembly). The table below provides a quick overview between the older and newer part numbers depending on wheel application.

IS-11003D

Service Bulletin/Repair Instructions

This Instruction sheet explains how to remplace MASTER ID? WITH ?MCM? MODULE

MI16-22

Service Bulletin/Repair Instructions

Use this maintenance information procedure to resolve an undesired behaviour on 2008-2012 vehicles. In sleep mode, certain marker lights may remain illuminated.

MI16-15A

Service Bulletin/Repair Instructions

The Beru sensors used on Prevost vehicles to monitor tire pressure (TPMS system) are being replaced by new Huf sensors and their corresponding stainless valves stems. Since the older and newer sensors are using different valve stems, replacement of a defective sensor on older vehicles will require the use of a new kit number (valve stem and sensor assembly). The table below provides a quick overview between the older and newer part numbers depending on wheel application.

MI12-04C

Service Bulletin/Repair Instructions

This Maintneance informations presents an improved harness and wiring modification procedure to avoid certain fault codes and messages.

Mi16-15

Service Bulletin/Repair Instructions

The Beru sensors used on Prevost vehicles to monitor tire pressure (TPMS system) are being replaced by new Huf sensors and their corresponding stainless valves stems. Since the older and newer sensors are using different valve stems, replacement of a defective sensor on older vehicles will require the use of a new kit number (valve stem and sensor assembly). The table below provides a quick overview between the older and newer part numbers depending on wheel application.

IS-14154

Service Bulletin/Repair Instructions

This Instruction sheet explains how to modify the Support beam (Part # 30022 Installation)- as part of the X3 Fuel Tank installation

MI16-16

Service Bulletin/Repair Instructions

This procedure explains how to perform a STARTER REMOVAL AND INSTALLATION, and does apply to Melco 105P70 starter part number #21212425.

IS-11003A

Service Bulletin/Repair Instructions

This Instruction sheet explains how to replace MASTER ID? WITH ?MCM? MODULE

MI15-18

Service Bulletin/Repair Instructions

This Maintenance Information does explain how five year old vehicles and older should be subjected to a thorough structural inspection.

IS-15003A

Service Bulletin/Repair Instructions

This instruction sheet explains how to use the Bosch HD10 24V-150A Altenrator Conversion Kit

MI15-02

Service Bulletin/Repair Instructions

This Maintenance Information presents an improved differential breather kit, identical to the one now used in production. This new breather incorporates a "J" shaped hose that prevents oil leakage and water ingestion while allowing the axle to vent.

WB14-47B

Service Bulletin/Repair Instructions

On the vehicles affected by this bulletin, perform a software update of ECM (Engine Control Module) and ACM (Aftertreatment Control Module) to provide improved temperature-related behaviour. The software will also change urea dosing valve behavior at shutdown and key-on. As an additional improvement, replace the urea dosing valve by an improved design. These hardware and software improvements aim to reduce the occurrence of clogging and shorting of the Urea Dosing Valve.

WB14-28E

Service Bulletin/Repair Instructions

On the vehicles affected by this bulletin, replace the LTD, relocate and replace the IR sensor as described in the following procedure.

SP14-306D

Service Bulletin/Repair Instructions

On the vehicles affected by this bulletin, replace the engine harness as described in the following procedure.

MI1423

Service Bulletin/Repair Instructions

A new software version (v1.06) is available to update the CANtrak (Tire Pressure Monitoring System) module. This new version will allows a 10 min. delay before the ?SYSTEM ERROR NOT ALL TIRES MONITORED? message appears in the vehicle cluster when a tire pressure sensor loses its connection. NOTE: The new software version will only delays the cluster message, the CANtrak screen will still displays a ??? code for the corresponding pressure sensor.

IS-14900

Service Bulletin/Repair Instructions

This Instruction Sheet explains how to replace 562489 Dimmer, using kit #069136

SP14-05B

Service Bulletin/Repair Instructions

On the vehicles affected by this bulletin, perform a turbo replacement if fault codes 27 FMI 7 or SPN641 FMI 7 or P004607 (OBD13) are found. Bulletin affects D13H engines with serial number from 984581 up to 1026719, excluded.

WB13-58

Service Bulletin/Repair Instructions

On the vehicles affected by this bulletin, change the flexible hose at the engine air intake

WB13-60

Service Bulletin/Repair Instructions

On the vehicles affected by this bulletin, a software update for the Volvo I-Shift transmission is required. Software update has for effect to improve the gear change process to avoid clashing and wear on the split gear. This software update is necessary on all I-shift transmission up to but not including serial number 1100224372.

IS-08080

Service Bulletin/Repair Instructions

When replacing a vehicle sound selector model VSS04 with a new sound selector model VSS05, an interface harness is required to connect the vehicle harness to the new sound selector model and a new VSS05 compatible radio unit must also be installed. This procedure describes the steps required to perform this update.

SP13-44

Service Bulletin/Repair Instructions

The light switch may operate incorrectly when doors are closed for vehicles affected by this bulletin. Corrective action is presented.

MI13-33

Service Bulletin/Repair Instructions

This Maintenance Information explains that polyester reinforced silicone hoses and elbowscan be repalced by aramid reinforced hoses and elbows for improved long term durability, and that constant torque hose clamps for silicone hoses with 5/8po, 3/4po, 7/8po, 1 1/8po and 1 3/8po inside diameter (I.D) can be replaced by new WAVE SEAL type constant torque hose clamps.

SP13-314

Service Bulletin/Repair Instructions

On the vehicles affected by this bulletin, follow the enclosed procedure to remove corrosion around luggage doors.

SP13-318

Service Bulletin/Repair Instructions

On the vehicles affected by this bulletin, take the following measure to improve dust handling. Seal the evaporator compartment to prevent dust entry, add ribs inside the duct to prevent collapse by the weight of accumulated dust, modify the trim molding above the evaporator door opening, and remove the additional mud pad under the vehicle.

SP13-319

Service Bulletin/Repair Instructions

On the vehicles affected by this bulletin, follow the enclosed procedure to correct surface corrosion on seat pedestals.

SP13-320

Service Bulletin/Repair Instructions

On the vehicles affected by this bulletin, if needed, the celling panel needs to be removed and material glued again.

SP13-321

Service Bulletin/Repair Instructions

On the vehicles affected by this bulletin, at next service occasion, open the C69 connector located in the front compartment and check for presence of corrosion. Relocate the connector horizontally.

SP13-322

Service Bulletin/Repair Instructions

On the vehicles affected by this bulletin, relocate the video fuse in the SMI box closer to the door for better access.

MI13-06

Service Bulletin/Repair Instructions

This Maintenance Information explains that hose clamps with a smaller diameter are available to increase the adjustment range at the upper and lower radiator flexible connections and at the oil cooler connections located under the turbocharger.

SP13-324

Service Bulletin/Repair Instructions

On the vehicles affected by this bulletin, an improved 90 degree elbow is available. Proceed to replacement at next service occasion.

MI-13-06

Service Bulletin/Repair Instructions

PREVOST: TO INCREASE VEHICLE'S PERFORMANCE, A MODIFICATION OF HOSE CLAMP FOR COOLING SYSTEM CONNECTION, IS RECOMMENDED. MODELS 2010-13 H3, 2010-13 H3 VIP CONVERTED, 2010-13 X3, 2012-13 X3 VIP CONVERTED, 2010-13 MTH XL2 ENTERTAINER, 2011 MTH XL2 CONVERTED. *PE

SP13-309

Service Bulletin/Repair Instructions

Multiple hose failures, agreed with customer to replace Silicone hose in engine compartment for coaches with Volvo engine.

SP13-306

Service Bulletin/Repair Instructions

On the vehicles affected by this bulletin, replace the Exhaust Gas Recirculation Venturi tube and sensor for an improved design.

WB12-31B

Service Bulletin/Repair Instructions

On the vehicles affected by this bulletin, a new and improved dipstick is available for installation.

IS11015B

Service Bulletin/Repair Instructions

This Instruction Sheet explains how to replace power relay p/n 561991 with improved power relay p/n 564218 and relay base p/n 564210

IS12047

Service Bulletin/Repair Instructions

This instruction sheet explains how to install additional restraint for plastic shields over drive axle wheels. Use kit #3200407 to secure the shields to the bus structure.

Reading this report

Complaint counts are reports filed with NHTSA, not failure rates. A common model collects more of them than a rare one that breaks more often.

2010 Prevost X3 Service Bulletins: 100 bulletins | CarFathom