MI16-32
Service Bulletin/Repair Instructions
Improved bearings are now available to replace the original bearings used on some Prevost vehicles idler pulleys.
Vehicle report
Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
MI16-32
Improved bearings are now available to replace the original bearings used on some Prevost vehicles idler pulleys.
IS-21072B
STEERING GATEWAY. Revision B - PIN 2 and 10 were inverted on connector A139
MI22-12B
Air Tanks Draining Sequence. Revision: B - General Update
MI22-12A
Air Tanks Draining Sequence. Revision: A - Erroneous Secondary & Accessory tanks location.
MI22-12
Air Tanks Draining Sequence
IS-17151C
Halogen to LED fog light replacement kit. Revision: C - Advanced kits canceled
IS-22902
TAG AXLE HUB FLANGE - ALTERNATE CAP SCREW
IS21-072
STEERING GATEWAY, revision A : Cancel watch dog removal from EFD part of the instruction
MI20-08C
STORAGE AND STARTUP GUIDELINES : part number updates
IS21-072A
STEERING GATEWAY Revision A Cancel watch dog removal from EFD part of the instruction
IS21-901
X3 SERIES ENVIROCARE - IONS AIR SANITIZER
IS20-925A
CENTRAL HVAC MERV FILTERS INSTALLATION
MI18-16B
BOSCH HD10 ALTERNATOR DIAGNOSTIC GUIDE Revision B To avoid replacement of alternators that are in fact in good working order, perform the steps which follow to help you perform a more precise diagnosis.
MI21-06
Diesel Exhaust Fluid ( DEF ) Contamination In Fuel System, Inspection And Repair â From US10 to newer engine generation
Mi21-07A
RONT & TAG AXLE â UNITIZED HUB BEARING END PLAY VERIFICATION AND REPLACEMENT
IS-18042
EBERSPACHER PREHEATER INSTALLATION In replacement of Spheros & Valeo preheaters
IS-20925A
CENTRAL HVAC MERV FILTERS INSTALLATION REVA
SP21-300
AUTOMATIC FIRE SUPPRESSION SYSTEM - TAMPER SEAL REPLACEMENT
IS-18091A
TIE ROD 610052 FIRST INSTALLATION INSTRUCTIONS: Use these instructions when replacing the drop joint tie rod on S82, S84 / S84U I-beam axles. The new tie rod will be adjusted to the length of the original; however, a steering alignment needs to be performed after replacement.
MI20-19B
INTRODUCING A NEW ENGINE COOLANT INTO PREVOST SERVICE CENTER NETWORK
MI20-19A
Rev A: Mention added concerning DDC Series 60 engine SCA requirement
MI21-01
VOLVO I-SHIFT TRANSMISSION REPLACEMENT - DIFFERENCE BETWEEN CONNECTIONS AT THE TOP OF THE OIL FILTER HOUSING
MI20-19
INTRODUCING A NEW ENGINE COOLANT INTO SERVICE
IS-20922
SIGMA PASSENGER SEATS PARTITION KIT
MI20-08B
STORAGE AND STARTUP GUIDELINES Revision: B Parts added to Suggested Material 08-10-2020
MI20-12
JERKY, NOISY OR HARD TO TURN STEERING GEARBOX. HYDRAULIC END LIMITER ADJUSTMENT. All models â equipped with RB Bosch/ZF Servocom or Servocomtronic steering gearbox
MI18-18B
GENERAL HOISTING AND TOWING PROCEDURES Revision: B Updated 2.1 to show rubber chocks, secure front and rear.
MI20-08A
STORAGE AND STARTUP GUIDELINES: Rev A: 21516229 replaced by 23381562 20523393 replaced by 21454749 800383 removed 611471 replaced by 611360 70376808 replaced by 21036050 21396642 replaced by 20967831
MI20-09
PREVOST VEHICLE DISINFECTION PROCEDURE
MI20-08
STORAGE AND STARTUP GUIDELINES - ALL PREVOST VEHICLES & VOLVO 9700
IS-19901A
ELECTRIC FAN DRIVE COOLING SYSTEM CONVERSION WITH BOSCH ALTERNATOR - X3 SERIES US10 UP TO GHG17 COOLING SYSTEM - Mention added stating to disable âPrimeâ; Parts added in the kit
IS-19912A
ELECTRIC FAN DRIVE COOLING SYSTEM CONVERSION WITH DELCO REMY ALTERNATOR - Mention added stating to disable âPrimeâ; Parts added in the kit.
MI15-24
Added: Power cables for L.H. side alternator & fan drive breaker box
FUELFILTER
Repair instructions to address fault codes P008A-00; P0087-00
NOX_Conv1
Repair instructions to address fault codes P207F-00 - Reductant Quality
NOx_Conv2
Repair instructions to address fault codes P207F-00; P20EE-00
IS-19066
This instruction sheet describes how to cut the air dryer bracket, to avoid dirt accumulation, and applies to vehicles with the air dryer located into the wheel pit .
IS-19040A
THIS INSTRUCTION SHEET EXPLAINS HOW TO REPLACE POWER STEERING PUMP DISCHARGE HOSE (PRESSURE) - #161335P OR #160039
IS-19901
This Instruction sheet explains how to install the Electric Cooling System with Bosch Alternators on X3 series vehicles equipped with US10 up to GHG17 engines
IS-17151
THIS INSTRUCTION SHEET EXPLAINS HOW TO REPLACE HALOGEN FOG LIGHT TO LED'S
SCI19-01C
The intent of this procedure is to guide you through the steps required to program a MCM especially for the control of the electric fan drive as required for conversion kit of instruction sheets IS-19900, IS-19901, IS19910, IS-19912.
SP19-301
On the vehicles affected by this bulletin, the compressor & radiator door lower hinges must be replaced by new stainless steel units
IS-18091
This Instruction Sheet explains how to perform the first installation of Tie Rod 610052 on Prevost vehicles equipped with Dana S82, S84 / S84U I-beam axles, 1994- today
IS-19915
MP-1000 MULTIMEDIA PLAYER INSTALLATION
IS-19922
PREVOST AWARE ADAPTIVE CRUISE BRAKING (ACB) FLR10 TO FLR21 RADAR SENSOR UPGRADE
IS-17071A
This instruction sheet explains how to install an ELD interface on OBD vehicles
IS-18910
This instruction sheet explains how to install a flap over the diesel filling cap
MI19-05
This Maintenance Information expains how to adjust p/n 660865, 660699 draglinks
MI19-06
This Maintenance Information is published to answer some questions regarding the inverted or ?trailing? mounting position of the drive axle brake calipers on Prevost vehicles
IS-19909
This instruction sheet explains how to perform alternator conversion, from Bosch to Delco Remy, on X3 vehicles
IS-13009D
This instruction sheet explains how to install and adjust drag link # 660699
SP18-13F
On the vehicles affected by this bulletin, proceed to the replacement of the drag link.
SCI18-46
This Service Center Instructions explains how to install the Prevost Ultimate Entertainment System
IS-13009C
This instruction sheet explains how to install and adjust drag link # 660699
WB18-43
This Warranty Bulletin explains how to update the VECU (Vehicle Electronic Control Unit) parameters to allow auto engine brake function with the I-Shift transmission.
IS-18907
This instruction sheet explains how to install hatches with fan on X3 vehicles.
Sp18-302
On the vehicles affected by this bulletin, install a pressure switch into the front service compartment to send a faster signal to the Allison transmission to switch to neutral at stop.
WB18-04
On the vehicles affected by this bulletin, update EMS and ACM software to the latest version available.
SP18-305A
On the vehicles affected by this bulletin, apply thread locker on the double door latch pins internal threads
MI18-21A
This Maintenance Information presents information about the Bitzer A/C compressor oil change interval and reminds technicians to clean the oil filter/strainer and the magnetic drain plug.
IS-15003E
This insruction Sheet explains how to insall the Bosch HD10 24v-150a Alternator Conversion Kit ? Twin Bosch Mounted On Volvo D13 Engine
MI16-17G
This Maintenance Information explains how to remove and install the Bosch HD10 (120A or 150A) alternators
MI18-18A
This maintenance information explains how to tow and hoist Prevost vehicles.
MI18-37
This Maintenance Information presents information about the removal or installation of the Lang KK73.1 electromagnetic clutch - part of the Bitzer (model 4NFCY) air conditioning compressor.
Sp18-301
On the vehicles affected by this bulletin, the existing surge tank support has to be replaced by a new configuration including two supports. That will allow a better distribution of the load between the tank and the support.
Sp18-303
On the vehicles affected by this bulletin, the condenser compartment wall may present fatigue cracks on or near the A/C receiver tank support. Follow these instructions to repair and improve the support.
Sp18-304A
For vehicles affected by this bulletin, on the wheelchair area sliding door, install a new upper roller carrier, adjust the door and inspect all fasteners.
MI18-18
This maintenance information explains how to tow and hoist Prevost vehicles.
MI18-16A
This Maintenance Information presents guidelines to help with the diagnosis of the Bosch HD10 alternators
SP17-314-R13
This bulletin explains how to install a light at the entrance door.
MI18-21
This Maintenance Information presents information about the Bitzer A/C compressor oil change interval and reminds technicians to clean the oil filter/strainer and the magnetic drain plug.
MI18-05
This maintenance information explains how to install valve assembly 130009 in replacement of valve 641274
MI18-02
This Mainteannce Informaiton presents the latest engine oil & filter change intervals for the Volvo Engine
SP17-314
This bulletin explains how to install a light at the entrance door.
MI16-17F
This Maintenance Information explains how to remove and install the Bosch HD10 (120A or 150A) alternators
WB15-19H
This bulletin explains how to add a reinforcement bracket to Bitzer A/C compressor to increase the installation stiffness and reduce vibration amplitude.
SP18-13E
On the vehicles affected by this bulletin, replace the drag link.
WB18-15
On the vehicles affected by this bulletin, the instrument cluster software must be updated. This mandatory cluster software update will raise the primary and secondary air system ?low pressure warning? set point.
IS-17905
This instruction sheet explains how to install an ELD interface kit on Pre-OBD Prevost Vehicles equipped with Volvo D13 Engines
SP18-13D
On the vehicles affected by this bulletin, proceed to the replacement of the drag link.
IS-13009B
This instruction sheet explains how to install and adjust drag link # 660699
wb17-16
On the vehicles affected by this bulletin, remove selected wires from C15 and C58 of the HVAC system wiring, and place them in new connectors C15B and C58B. New connectors have a higher amp rating. We recommend inspecting connectors C15 & C58 for heat damage before ordering parts. Depending on connector condition, order additional parts along with main kit. See Additional Parts table.
Sp18-300
This bulletin explains how to replace ceiling transition pannels, when needed
MI17-22
This Maintenance Information explains how to inspect the Fuel Tank Cradle Mounting Screws on a yearly basis
IS-17071
This instruction sheet explains how to install an ELD interface on OBD vehicles
IS-17907
This instruction sheet explains how to install the Volvo Electronic Logging Device (ELD)
SP17-313
On the vehicles affected by this bulletin, replace the batteries by a new set (4) of the same model; perform several verifications on the alternator and charging circuit. Finally, update the multiplex software to the latest version and disable Alternator Management on select vehicles.
CK17-27
This conversion kit explains how to to disable the ACB radar.
Sp17-312A
On the vehicles affected by this bulletin, bus washing operations can result in water dripping into the front service compartment. Add a drip guard above the entrance door valve.
Sp17-313
On the vehicles affected by this bulletin, replace the batteries by a new set (4) of the same model; perform several verifications on the alternator and charging circuit. Finally, update the multiplex software to the latest version.
CK17-19A
This conversion kit explains how to remove TGW1 from vehicles using Tech Tool, no manual VDA changes needed. This conversion kit will work for any vehicle equipped with TGW1 up to the VIN's listed on the bulletin.
WB17-16
On the vehicles affected by this bulletin, on the HVAC system wiring, remove selected wires from C15 and C58 and place them in new connectors C15B and C58B. New connectors have a higher amp rating.
SP16-311G
On the vehicles affected by this bulletin, add Z clips to secure the direct light lenses, 13 lenses per vehicle.
Sp17-312
On the vehicles affected by this bulletin, bus washing operations can result in water dripping into the front service compartment. Add a drip guard above the entrance door valve.
sp17-310
On the vehicles affected by this bulletin, it is necessary to replace the two engine door latch pins and the compressor door latch pin by new units made of sturdier material.
IS-15003D
This insruction Sheet explains how to insall the Bosch HD10 24v-150a Alternator Conversion Kit ? Twin Bosch Mounted On Volvo D13 Engine
Sp17-311
On the vehicles affected by this bulletin, replace connector C12 installed inside the DPF access door with an improved version providing a better seal.
SP17-307
This bulletin explains how to replace the Radiator Door Upper Hinge
IS-16100
This instruction sheet explains how to install latest radio models
SP17-303D
On the vehicles affected by this bulletin, replace two idlers by an improved version on the alternator drive belt and on the A/C belts.
IS-16048
This instruction sheet explains how to install a WCL Manual lock
WB17-06
On the vehicles affected by this bulletin, replace the existing wheelchair lift control pendant support by an improved version.
IS-15003C
This instruction sheet explains how to use the Bosch HD10 24V-150A Alternator Conversion Kit
Sp16-320
On the vehicles affected by this bulletin, the compressor door support to the vehicle must be improved by the addition of a lower support bracket and the replacement of the two door hinges. A support plate must also be riveted to the door frame between the hinges to add structural rigidity and prevent stress cracks to the door assembly.
Sp16-326B
On the vehicles affected by this bulletin, re-torque the clamps on specific coolant hoses of the cooling system.
MI16-17E
This Maintenance Information explains how to remove and install the Bosch HD10 (120A or 150A) alternator.
MI16-17D
Use this procedure for the removal and installation of the twin Bosch HD10 (120A or 150A) Alternators.
SP16-326
On the vehicles affected by this bulletin, re-torque the clamps on specific coolant hoses of the cooling system.
SP16-43A
On the vehicles affected by this bulletin, coolant may leak by the coolant level sensor wires on the surge tank. Replace the sensor with an improved version.
IS-15003B
This instruction sheet explains how to use the Bosch HD10 24V-150A Alternator Conversion Kit
SP16-311B
On the vehicles affected by this bulletin, add two clips to secure the direct light lenses, 13 lenses per vehicle.
Sp16-323
On the vehicles affected by this bulletin, change a parameter in the MUX system to deactivate a DTC corresponding to air dryer cartridge change warning.
MI16-15B
The Beru sensors used on Prevost vehicles to monitor tire pressure (TPMS system) are being replaced by new Huf sensors and their corresponding stainless valves stems. Since the older and newer sensors are using different valve stems, replacement of a defective sensor on older vehicles will require the use of a new kit number (valve stem and sensor assembly). The table below provides a quick overview between the older and newer part numbers depending on wheel application.
Sp16-309A
On the vehicles affected by this bulletin, secure the mounting of the curb side engine door electrical fan.
IS-16902
This instruction sheet explains how to install and adjust Brake Pedal kit IS16902
Sp16-317
On the vehicles affected by this bulletin, it is necessary to ensure proper brake pedal installation and adjustment following the procedure below.
Wb16-29
On the vehicles affected by this bulletin, update EMS and ACM software to the latest version available. This update must be carried out by qualified technicians. As soon as possible, make an appointment with your nearest Prevost Service Center or contact your service manager to carry out the update.
MI16-14
Use this procedure when a suspension height check or adjustment must be performed.
Mi16-28
This Maintenance information explains that on vehicles equipped with Ramco rear-view mirrors in winter conditions, ice may accumulate in the gap between the glass bottom edge and shell. The ice may impede mirror adjustment. Installing a drip edge will prevent ice accumulation permanently by diverting water outwards. The proposed drip edge may only be installed on mirrors having a flat glass in the lower section of the mirror.
SP16-306A
On the vehicles affected by this bulletin, replace an access panel aft of the tag axle wheel, road side.
Sp16-302A
On the vehicles affected by this bulletin, replace the pressure cap on the surge tank.
Sp16-313A
On the vehicles affected by this bulletin, coolant may leak by the coolant level sensor wires on the surge tank. Replace the sensor with an improved version.
Sp16-311A
On the vehicles affected by this bulletin, add two clips to secure the direct light lenses, 13 lenses per vehicle.
SP16-21
On the vehicles affected by this bulletin, perform the proactive replacement of the lower hinges for both service doors.
MI16-23
This Maintenance Information explains that decals are available to update the front junction box on 2013 to 2016 Prevost vehicles; the decals will provide updated information and component descriptions. Refer to the identification part of this bulletin to locate the decal part number currently used on specific vehicles.
SP16-306
On the vehicles affected by this bulletin, replace an access panel aft of the tag axle wheel, road side.
SP16-25
On the vehicles affected by this bulletin install an updated proximity switch on the vehicle compressor door following Instruction Sheet IS-12026.
MI16-10
This information letter applies only to vehicles equipped with 19000 lb Independent Front Suspension (IFS) and 22.5 x 10.5 Alcoa aluminum wheels for 365/70 R 22.5 size tires. When balancing this wheel for installation on the IFS, a specific type and size of clamp-on wheel weight should be used to provide the appropriate clearance with components of the suspension.
MI16-15A
The Beru sensors used on Prevost vehicles to monitor tire pressure (TPMS system) are being replaced by new Huf sensors and their corresponding stainless valves stems. Since the older and newer sensors are using different valve stems, replacement of a defective sensor on older vehicles will require the use of a new kit number (valve stem and sensor assembly). The table below provides a quick overview between the older and newer part numbers depending on wheel application.
Sp16-309
On the vehicles affected by this bulletin, secure the mounting of the curb side engine door electrical fan.
Wb15-19F
On the vehicles affected by this bulletin, vibration is causing damage to A/C compressor and compressor harness connectors. Addition of a reinforcement bracket to Bitzer A/C compressor is needed to increase the installation stiffness and reduce vibration amplitude.
Mi16-15
The Beru sensors used on Prevost vehicles to monitor tire pressure (TPMS system) are being replaced by new Huf sensors and their corresponding stainless valves stems. Since the older and newer sensors are using different valve stems, replacement of a defective sensor on older vehicles will require the use of a new kit number (valve stem and sensor assembly). The table below provides a quick overview between the older and newer part numbers depending on wheel application.
SP16-304
On the vehicles affected by this bulletin, replace the battery connection decal by a new version.
IS-14154
This Instruction sheet explains how to modify the Support beam (Part # 30022 Installation)- as part of the X3 Fuel Tank installation
MI16-16
This procedure explains how to perform a STARTER REMOVAL AND INSTALLATION, and does apply to Melco 105P70 starter part number #21212425.
SP15-304E
On the vehicles affected by this bulletin, the Bosch HD10 alternators need to be replaced with new Bosch HD10PLBH 150 Amps alternators.
WB15-55
On the vehicles affected by this bulletin, inspect the gap between the radius rod support and the front axle. A deviation in the axle beam envelope can lead to interference between the two parts. In most cases, slightly moving the support will resolve the issue. In certain cases, replacing a set screw will be required. Exceptionally, the axle may need to be replaced.
SP16-302
On the vehicles affected by this bulletin, replace the pressure cap on the surge tank.
MI16-05
This Maintenance Information shares information about the Bendix M-32QR valve replaced by M-40QR model htat need to be taken into consideration, specially when switching them for the first time on a vehicle.
SP15-341C
On the vehicles affected by this bulletin, replace the horn support by 140034.
WB15-19E
On the vehicles affected by this bulletin, vibration is causing damage to A/C compressor and compressor harness connectors. Addition of a reinforcement bracket to Bitzer A/C compressor is needed to increase the installation stiffness and reduce vibration amplitude.
SP15-324E
On the vehicles affected by this bulletin, vibration is causing damage to A/C compressor and compressor harness connectors. Addition of a reinforcement bracket to Bitzer A/C compressor is needed to increase the installation stiffness and reduce vibration amplitude.
IS-15907A
This Instruction Sheet explains how to assemble the BENDIX FLR10 AND FLR20 RADAR SENSOR ALIGNMENT TOOL
MI15-41
This Maintenance Information reminds Prevost customers that cleaning products designed for external washing of vehicles should be used for exterior vehicle wash and in particular, for the washing of polycarbonate taillights.
MI15-43
New aramid cord poly-v belts are now available to replace the polyester cord alternator belts previously used on Prevost vehicles equipped with Bosch HD10 alternators.
MI15-18
This Maintenance Information does explain how five year old vehicles and older should be subjected to a thorough structural inspection.
IS-15003A
This instruction sheet explains how to use the Bosch HD10 24V-150A Altenrator Conversion Kit
IS-13169A
This Instruction Sheet explains how to install the AWARE ADAPTIVE CRUISE BRAKING (ACB) FLR20 RADAR SENSOR REPLACEMENT kits # 145372 and 145373
MI15-02
This Maintenance Information presents an improved differential breather kit, identical to the one now used in production. This new breather incorporates a "J" shaped hose that prevents oil leakage and water ingestion while allowing the axle to vent.
SP14-323
On the vehicles affected by this bulletin, replace the brake pedal assembly.
SP14-324B
On the vehicles affected by this bulletin, replace the front bumper retaining spring.
SP14-330
On the vehicles affected by this bulletin, replace the IMRON painted marker light guards with powder coated marker lights.
SP14-331A
On the vehicles affected by this bulletin, replace the various bus bars and place one insulation sheet beside the breaker plate
SP14-332
On the vehicles affected by this bulletin, inspect the transmission oil cooler to make sure it is properly secured. In certain material conditions, the bolts may extend beyond the threaded length of the mounting holes in the cooler creating a condition where the support is not tight on the cooler frame. Change the mounting bolts if required.
SP14-334
On the vehicles affected by this bulletin, install a lanyard on each of the two overhead access panels in the front section of the bus interior.
SP14-335
On the vehicles affected by this bulletin, add a support on the curbside of the drive axle.
SP14-320B
On the vehicles affected by this bulletin, perform a software update of ECM and ACM to modify the dosing strategy. The software will also improve urea dosing valve behavior at shutdown and key-on. As an additional improvement, replace the urea dosing valve by an improved design and modify coolant hose routing to the dozer valve to provide additional cooling at engine shutdown.
SP14-322
On the vehicles affected by this bulletin, Add or replace insulating sheets in the rear electrical compartment and battery box.
SP14-325
On the vehicles affected by this bulletin, add a new engine compartment curbside door and a temperature probe behind the alternators along with corresponding wiring additions and updates.
SP14-326
On the vehicles affected by this bulletin, the compressor belt may not be tensioned properly since the reduction of the diameter of the pulley on the commuters.
SP14-316
On the vehicles affected by this bulletin, replace the exhaust pipe thermal insulation blankets.
SP14-317A
On the vehicles affected by this bulletin, identify the live wires in the rear electrical compartment according to instructions.
SP14-318
On the vehicles affected by this bulletin, the steering wheel shaft joint angles are different from the intended design values due to a parts shortage. Replace the steering wheel shaft with the components specified on the bill of material.
WB14-47B
On the vehicles affected by this bulletin, perform a software update of ECM (Engine Control Module) and ACM (Aftertreatment Control Module) to provide improved temperature-related behaviour. The software will also change urea dosing valve behavior at shutdown and key-on. As an additional improvement, replace the urea dosing valve by an improved design. These hardware and software improvements aim to reduce the occurrence of clogging and shorting of the Urea Dosing Valve.
SP14-315
On the vehicles affected by this bulletin, Change the connection arrangement behind circuit breaker CB2.
WB14-45C
On the vehicles affected by this bulletin remove the ACM relay and base identified R49. Reconnect the 24V power wire and protect the remaining signal wires with shrink tube.
IS-13169
This Instruction Sheet explains how to install the AWARE ADAPTIVE CRUISE BRAKING (ACB) FLR20 RADAR SENSOR REPLACEMENT kits # 145372 and 145373
SP14-46
This bulletin is performed on a fix as fail basis. On the vehicles affected by this bulletin, update to the latest configuration of wiring and sensors for the Bitzer compressor.
WB14-44B
On the vehicles affected by this bulletin, changing of VECU (Vehicle Electronic Control Unit) parameters is necessary. This update must be carried out by qualified technicians. Make an appointment with your nearest Prevost Service Center. ELECTRIC AIR DRYER CUT-OFF PRESSURE & DESICCANT REGENERATION FACTOR This update involves all OBD13 & GHG14 vehicles in service (refer to Application table for involved vehicles range). This update will reduce air dryer cut-off pressure from 144 psi to 140 psi and extend desiccant regeneration time, thus preventing presence of water in the accessory tank.
SP14-313
On the vehicles affected by this special bulletin, a 7psi pressure switch must be added to the transmission retarder circuit to activate the retarder when vehicle brakes are applied, increasing drivetrain components reliability.
WB14-42A
On the vehicles affected by this bulletin, perform a power source improvement and a multiplex software update for the steering Gateway module. On a limited number of vehicles, the module will be replaced with the latest version of the part.
WB14-37
On the vehicles affected by this bulletin, replace the engine info label for an updated version. H series vehicles require two labels. X-series vehicles require only one label.
SP14-309
On the vehicles affected by this special bulletin, replace the two visual brake wear indicators on the tag axle.
WB14-08C
On the vehicles affected by this bulletin, verify the revision numbers of the steering wheel gateway module and multiplex software. If applicable, replace with the latest version. A power source improvement is also required. On some vehicles, as a temporary measure, a switch was installed on the left dashboard for cruise control SET and RESUME. This installation must be removed to restore these controls to the steering wheel.
MI1434C
This Maintenance Information presents how to align the PREVOST AWARE ADAPTIVE CRUISE BRAKING (ACB)FLR20 RADAR SENSOR.
WB14-06G
On the vehicles affected by this bulletin, perform the following verifications and modifications on the A/C system: Bulletin is divided in five steps, refer to detailed instructions below. STEP 1: Unloader replacement (Step moved to Warranty Bulletin WB15-19) STEP 2: System vacuum, wiring update, remote pressure transducer and switch installation. STEP 3: Seal the evaporator compartment ventilation discharge duct. STEP 4: Check Evaporator expansion valve bulb position and MUX software version. STEP 5: Dynamic A/C system test to confirm all functions operate correctly.
WB14-28E
On the vehicles affected by this bulletin, replace the LTD, relocate and replace the IR sensor as described in the following procedure.
SP14-306D
On the vehicles affected by this bulletin, replace the engine harness as described in the following procedure.
MI1423
A new software version (v1.06) is available to update the CANtrak (Tire Pressure Monitoring System) module. This new version will allows a 10 min. delay before the ?SYSTEM ERROR NOT ALL TIRES MONITORED? message appears in the vehicle cluster when a tire pressure sensor loses its connection. NOTE: The new software version will only delays the cluster message, the CANtrak screen will still displays a ??? code for the corresponding pressure sensor.
SP14-30
On the identified drive axles, the wheel nut may not be secured by the locking Tab.
WB14-27
On the vehicles affected by this bulletin, interference may occur between a cable bundle and part of the drive axle surrounding structure when suspension is completely lowered.
SP14-17
Inspect the wall anchor bolts. Make sure the washers under bolt head are locking washers and not flat washer.
IS-14900
This Instruction Sheet explains how to replace 562489 Dimmer, using kit #069136
WB13-65D
On the vehicles affected by this bulletin, software updates with enhancements are available for the multiplex system, for the EMS and aftertreatment control module (ACM). On all vehicles, perform a DPF Service Regeneration and Crystal Sublimation when programming is completed.
WB13-58
On the vehicles affected by this bulletin, change the flexible hose at the engine air intake
WB13-62B
On the vehicles affected by this bulletin, torque must be verified on one of the axle support mounting bolts. An interference of a production tool with the casting on the nut side of the fastener may have resulted in lower effective torque.
WB13-63A
On the vehicles affected by this bulletin, inspection and replacement of 70 amp circuit breakers in the rear electrical compartments is required.
WB13-55A
On the vehicles affected by this bulletin, the upper support of the tripod fan support must be inspected for the presence of weld. If no weld is found, it must be replaced.
SP13-52
Risk of premature failure of top fan support due to absence of weld. In the engine compartment above radiator, inspect support to make sure support has two welds in the corners.
SP13-34A
On the vehicles affected by this bulletin, a relay needs to be added to allow the DEF to return to the tank after turning the key to the OFF position. In addition, the ACM & MCM need to be reprogrammed to the latest version.
SP13-22
Radius rod support weld inspection: weld beads may be too small on radius rod supports on rear sub-frame.
IS11015B
This Instruction Sheet explains how to replace power relay p/n 561991 with improved power relay p/n 564218 and relay base p/n 564210
Complaint counts are reports filed with NHTSA, not failure rates. A common model collects more of them than a rare one that breaks more often.