IS-21072B
Service Bulletin/Repair Instructions
STEERING GATEWAY. Revision B - PIN 2 and 10 were inverted on connector A139
Vehicle report
Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
IS-21072B
STEERING GATEWAY. Revision B - PIN 2 and 10 were inverted on connector A139
MI22-12B
Air Tanks Draining Sequence. Revision: B - General Update
MI22-12A
Air Tanks Draining Sequence. Revision: A - Erroneous Secondary & Accessory tanks location.
SP18-35J
P20EE (diagnostic troubleshooting code) SOLUTION - NOX CONVERSION EFFICIENCY. Revision J - Range of applicable VINs updated.
MI22-12
Air Tanks Draining Sequence
IS-17151C
Halogen to LED fog light replacement kit. Revision: C - Advanced kits canceled
IS-22902
TAG AXLE HUB FLANGE - ALTERNATE CAP SCREW
IS21-072
STEERING GATEWAY, revision A : Cancel watch dog removal from EFD part of the instruction
MI20-08C
STORAGE AND STARTUP GUIDELINES : part number updates
IS21-072A
STEERING GATEWAY Revision A Cancel watch dog removal from EFD part of the instruction
IS21-901
X3 SERIES ENVIROCARE - IONS AIR SANITIZER
IS20-925A
CENTRAL HVAC MERV FILTERS INSTALLATION
IS22-040
BRAKE PEDAL SEAL PLATE INSTALLATION KIT
SP18-35H
P20EE (diagnostic troubleshooting code) SOLUTION - NOX CONVERSION EFFICIENCY
IS19-108
Surge tank pressure cap replacement
SP18-39D
SCR CONVERTER REPLACEMENT - AFTERTREATMENT SYSTEM
MI18-16B
BOSCH HD10 ALTERNATOR DIAGNOSTIC GUIDE Revision B To avoid replacement of alternators that are in fact in good working order, perform the steps which follow to help you perform a more precise diagnosis.
MI21-13A
An automated test is available to check the big HVAC superheat from the driver seat. This test is controlled by Multiplex, eliminating interventions and the need to take measures on the vehicle.
SR19-31C
ENGINE CONTROL MODULE (ECM) SOFTWARE UPDATE - Engine Cooling Strategy in High Altitude Operation Revision C: VIN range in application box rearranged for H3 coaches
MI21-06
Diesel Exhaust Fluid ( DEF ) Contamination In Fuel System, Inspection And Repair â From US10 to newer engine generation
Mi21-07A
RONT & TAG AXLE â UNITIZED HUB BEARING END PLAY VERIFICATION AND REPLACEMENT
IS-18042
EBERSPACHER PREHEATER INSTALLATION In replacement of Spheros & Valeo preheaters
SP18-35F
P20EE (diagnostic troubleshooting code) SOLUTION - NOX CONVERSION EFFICIENCY Rev E: expiration date removed
IS-20925A
CENTRAL HVAC MERV FILTERS INSTALLATION REVA
IS-18091A
TIE ROD 610052 FIRST INSTALLATION INSTRUCTIONS: Use these instructions when replacing the drop joint tie rod on S82, S84 / S84U I-beam axles. The new tie rod will be adjusted to the length of the original; however, a steering alignment needs to be performed after replacement.
MI20-19B
INTRODUCING A NEW ENGINE COOLANT INTO PREVOST SERVICE CENTER NETWORK
MI20-19A
Rev A: Mention added concerning DDC Series 60 engine SCA requirement
MI21-01
VOLVO I-SHIFT TRANSMISSION REPLACEMENT - DIFFERENCE BETWEEN CONNECTIONS AT THE TOP OF THE OIL FILTER HOUSING
MI20-19
INTRODUCING A NEW ENGINE COOLANT INTO SERVICE
IS-20922
SIGMA PASSENGER SEATS PARTITION KIT
MI20-08B
STORAGE AND STARTUP GUIDELINES Revision: B Parts added to Suggested Material 08-10-2020
MI20-12
JERKY, NOISY OR HARD TO TURN STEERING GEARBOX. HYDRAULIC END LIMITER ADJUSTMENT. All models â equipped with RB Bosch/ZF Servocom or Servocomtronic steering gearbox
MI18-18B
GENERAL HOISTING AND TOWING PROCEDURES Revision: B Updated 2.1 to show rubber chocks, secure front and rear.
MI20-08A
STORAGE AND STARTUP GUIDELINES: Rev A: 21516229 replaced by 23381562 20523393 replaced by 21454749 800383 removed 611471 replaced by 611360 70376808 replaced by 21036050 21396642 replaced by 20967831
MI20-09
PREVOST VEHICLE DISINFECTION PROCEDURE
MI20-08
STORAGE AND STARTUP GUIDELINES - ALL PREVOST VEHICLES & VOLVO 9700
MI15-24
Added: Power cables for L.H. side alternator & fan drive breaker box
FUELFILTER
Repair instructions to address fault codes P008A-00; P0087-00
NOX_Conv1
Repair instructions to address fault codes P207F-00 - Reductant Quality
NOx_Conv2
Repair instructions to address fault codes P207F-00; P20EE-00
IS-19921A
This instruction Sheet explains how to install a seatbelt cutter in the driver's area
IS-19066
This instruction sheet describes how to cut the air dryer bracket, to avoid dirt accumulation, and applies to vehicles with the air dryer located into the wheel pit .
IS-19040A
THIS INSTRUCTION SHEET EXPLAINS HOW TO REPLACE POWER STEERING PUMP DISCHARGE HOSE (PRESSURE) - #161335P OR #160039
IS-17151
THIS INSTRUCTION SHEET EXPLAINS HOW TO REPLACE HALOGEN FOG LIGHT TO LED'S
SCI19-01C
The intent of this procedure is to guide you through the steps required to program a MCM especially for the control of the electric fan drive as required for conversion kit of instruction sheets IS-19900, IS-19901, IS19910, IS-19912.
SP18-35D_English
On vehicles with active code P20EE, perform the following checklist and operations.
IS-18091
This Instruction Sheet explains how to perform the first installation of Tie Rod 610052 on Prevost vehicles equipped with Dana S82, S84 / S84U I-beam axles, 1994- today
sp19-26A
On the vehicles affected by this bulletin, an update to the engine EMS software must be carried out by qualified technicians. Contact your Service Manager to schedule an appointment and have the update performed
IS-18158
TOILET DRAIN VALVE REPLACEMENT
IS-19915
MP-1000 MULTIMEDIA PLAYER INSTALLATION
SCI19-20
On the vehicles affected by this bulletin, the vehicle program has to be upgraded. This allows the Intelligent Sleep Mode (ISM) system improvement to prevent batteries drain when ISM is enabled. This procedure shows how to generate the Vehicle Program last update and how to transfer the program to the vehicle owner. Refer to bulletin WB19-11 for the upgrade procedure.
Wb19-11
On the vehicles affected by this bulletin, the vehicle program might need to be upgraded to prevent batteries drain when ISM (Intelligent Sleep Mode) is enabled.
SP18-35B_English
On vehicles with active code P20EE, perform the following checklist and operations.
IS-17071A
This instruction sheet explains how to install an ELD interface on OBD vehicles
IS-18910
This instruction sheet explains how to install a flap over the diesel filling cap
SP18-39B
This Special Bulletin explains how to perform the replacement of the SCR tank, when authorized.
MI19-05
This Maintenance Information expains how to adjust p/n 660865, 660699 draglinks
MI19-06
This Maintenance Information is published to answer some questions regarding the inverted or ?trailing? mounting position of the drive axle brake calipers on Prevost vehicles
IS-17102A
This Instruction sheet explains how to install ISM (Intelligent Sleep Mode) On X Series With Prime Hardware
IS-19906
This instruction sheet explains how to perform alternator conversion, from Bosch to Delco Remy, on X3 vehicles equipped with EFD
SCI18-46
This Service Center Instructions explains how to install the Prevost Ultimate Entertainment System
Sp18-39A
This Special Bulletin explains how to perform the replacement of the SCR tank, when authorized.
SP18-39
This Special Bulletin explains how to perform the replacement of the SCR tank, when authorized.
Sp18-35
On vehicles with active code P20EE, perform the following checklist and operations.
MI18-28
On the vehicles affected by this bulletin, the compressor door may be adjusted for proper fit following the procedure below.
SP18-308A
On the vehicles affected by this bulletin, add 300ml of oil in the Bitzer A/C compressor as per production retrofit R18053.
SP18-306
On the vehicles affected by this bulletin, update EMS and ACM software to the latest version available.
WB18-04
On the vehicles affected by this bulletin, update EMS and ACM software to the latest version available.
IS-18904
This procedure shows how to install a rear camera.
MI18-27B
This maintenance information presents the Amerex fire suppression system, and its recommended maintenance
WB18-01A
On the vehicles affected by this bulletin, it is necessary to add two metal reinforcement plates to all the parcel rack door supports that are holding a door gas shock.
MI18-21A
This Maintenance Information presents information about the Bitzer A/C compressor oil change interval and reminds technicians to clean the oil filter/strainer and the magnetic drain plug.
MI18-18A
This maintenance information explains how to tow and hoist Prevost vehicles.
MI18-37
This Maintenance Information presents information about the removal or installation of the Lang KK73.1 electromagnetic clutch - part of the Bitzer (model 4NFCY) air conditioning compressor.
MI18-27A
This maintenance information presents the Amerex fire suppression system, and its recommended maintenance
MI18-27
This maintenance information presents the Amerex fire suppression system, and its recommended maintenance
IS-18901
This instruction sheet explains how to install the engine belt guard on X3 Series vehicles with coolant system electrical fan drive.
MI18-18
This maintenance information explains how to tow and hoist Prevost vehicles.
WB18-07B
On the vehicles affected by this bulletin, the busbar connected to circuit breaker CB13 (power inverter) may have been installed reversely. It is necessary to check and to correct the installation if applicable. In the case of improper installation, it is also necessary to check if the threads of the circuit breaker stud are damaged.
Sp18-20
On the vehicles affected by this bulletin, replace the AC compressor discharge hose.
MI18-16A
This Maintenance Information presents guidelines to help with the diagnosis of the Bosch HD10 alternators
MI18-22
This Maintenance Information presents information about the ELD Installation and Parameter List on Prevost Coaches
MI18-21
This Maintenance Information presents information about the Bitzer A/C compressor oil change interval and reminds technicians to clean the oil filter/strainer and the magnetic drain plug.
WB18-06
On the vehicles affected by this bulletin, replace the existing right console ramp p/n 392494 with the new right console ramp p/n 3200962.
MI18-02
This Mainteannce Informaiton presents the latest engine oil & filter change intervals for the Volvo Engine
WB18-07A
On the vehicles affected by this bulletin, the busbar connected to circuit breaker CB13 (power inverter) may have been installed reversely. It is necessary to check and to correct the installation if applicable. In the case of improper installation, it is also necessary to check if the threads of the circuit breaker stud are damaged.
IS-17905
This instruction sheet explains how to install an ELD interface kit on Pre-OBD Prevost Vehicles equipped with Volvo D13 Engines
WB18-07
On the vehicles affected by this bulletin, the busbar connected to circuit breaker CB13 (power inverter) may have been installed reversely. It is necessary to check and to correct the installation if applicable. In the case of improper installation, it is also necessary to check if the threads of the circuit breaker stud are damaged.
IS-13009B
This instruction sheet explains how to install and adjust drag link # 660699
IS-18902
This instruction sheet explains how to installa parcel rack door kits
WB18-08
On the vehicles affected by this bulletin use the following procedure to install the engine belt guard.
WB18-09
On the vehicles affected by this bulletin, one of the battery ground cables may have been incorrectly crimped and must be replaced following the procedure below.
WB18-03
On the vehicles affected by this bulletin, due to a software issue, replace the battery equalizer in the main power compartment.
Wb18-01
On the vehicles affected by this bulletin, it is necessary to add two metal reinforcement plates to all the parcel rack door supports that are holding a door gas shock.
MI17-22
This Maintenance Information explains how to inspect the Fuel Tank Cradle Mounting Screws on a yearly basis
IS-17071
This instruction sheet explains how to install an ELD interface on OBD vehicles
IS-17907
This instruction sheet explains how to install the Volvo Electronic Logging Device (ELD)
CK17-30
On the vehicles affected by this bulletin, it is now possible to replace the older generation TGW 2.0 (3G network) by the newer 2.1 version (4G the network) using accessory kit 23266301 and the following procedure.
CK17-26
On the vehicles affected by this bulletin, it is now possible to disable the engine brake automatic function by running accessory kit # 23181730.
SP17-18
On the vehicles affected by this bulletin, remove relay R26, isolate and/or reconnect wires according to the wiring diagram D061670 P18.2 revision 8. Also move water pump ground connection to the electronic ground pin A54 J2.14 and rename circuit gnd-0EVAP2-14.
Complaint counts are reports filed with NHTSA, not failure rates. A common model collects more of them than a rare one that breaks more often.