Vehicle report

2014 PREVOST X3VIP

Service bulletins

86 bulletins

Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.

MI16-32

Service Bulletin/Repair Instructions

Improved bearings are now available to replace the original bearings used on some Prevost vehicles idler pulleys.

IS-19912E

Service Bulletin/Repair Instructions

ELECTRIC FAN DRIVE COOLING SYSTEM CONVERSION WITH DELCO REMY ALTERNATOR. REVISION: E Note added regarding power cable connection

IS-21072B

Service Bulletin/Repair Instructions

STEERING GATEWAY. Revision B - PIN 2 and 10 were inverted on connector A139

MI22-12B

Service Bulletin/Repair Instructions

Air Tanks Draining Sequence. Revision: B - General Update

MI22-12A

Service Bulletin/Repair Instructions

Air Tanks Draining Sequence. Revision: A - Erroneous Secondary & Accessory tanks location.

MI22-12

Service Bulletin/Repair Instructions

Air Tanks Draining Sequence

IS-17151C

Service Bulletin/Repair Instructions

Halogen to LED fog light replacement kit. Revision: C - Advanced kits canceled

IS-22902

Service Bulletin/Repair Instructions

TAG AXLE HUB FLANGE - ALTERNATE CAP SCREW

IS21-072

Service Bulletin/Repair Instructions

STEERING GATEWAY, revision A : Cancel watch dog removal from EFD part of the instruction

MI20-08C

Service Bulletin/Repair Instructions

STORAGE AND STARTUP GUIDELINES : part number updates

IS21-072A

Service Bulletin/Repair Instructions

STEERING GATEWAY Revision A Cancel watch dog removal from EFD part of the instruction

IS21-901

Service Bulletin/Repair Instructions

X3 SERIES ENVIROCARE - IONS AIR SANITIZER

IS20-925A

Service Bulletin/Repair Instructions

CENTRAL HVAC MERV FILTERS INSTALLATION

MI18-16B

Service Bulletin/Repair Instructions

BOSCH HD10 ALTERNATOR DIAGNOSTIC GUIDE Revision B To avoid replacement of alternators that are in fact in good working order, perform the steps which follow to help you perform a more precise diagnosis.

MI21-06

Service Bulletin/Repair Instructions

Diesel Exhaust Fluid ( DEF ) Contamination In Fuel System, Inspection And Repair – From US10 to newer engine generation

Mi21-07A

Service Bulletin/Repair Instructions

RONT & TAG AXLE – UNITIZED HUB BEARING END PLAY VERIFICATION AND REPLACEMENT

IS-20925A

Service Bulletin/Repair Instructions

CENTRAL HVAC MERV FILTERS INSTALLATION REVA

MI20-19B

Service Bulletin/Repair Instructions

INTRODUCING A NEW ENGINE COOLANT INTO PREVOST SERVICE CENTER NETWORK

MI20-19A

Service Bulletin/Repair Instructions

Rev A: Mention added concerning DDC Series 60 engine SCA requirement

MI21-01

Service Bulletin/Repair Instructions

VOLVO I-SHIFT TRANSMISSION REPLACEMENT - DIFFERENCE BETWEEN CONNECTIONS AT THE TOP OF THE OIL FILTER HOUSING

MI20-19

Service Bulletin/Repair Instructions

INTRODUCING A NEW ENGINE COOLANT INTO SERVICE

MI20-12

Service Bulletin/Repair Instructions

JERKY, NOISY OR HARD TO TURN STEERING GEARBOX. HYDRAULIC END LIMITER ADJUSTMENT. All models – equipped with RB Bosch/ZF Servocom or Servocomtronic steering gearbox

MI18-18B

Service Bulletin/Repair Instructions

GENERAL HOISTING AND TOWING PROCEDURES Revision: B Updated 2.1 to show rubber chocks, secure front and rear.

MI20-08A

Service Bulletin/Repair Instructions

STORAGE AND STARTUP GUIDELINES: Rev A: 21516229 replaced by 23381562 20523393 replaced by 21454749 800383 removed 611471 replaced by 611360 70376808 replaced by 21036050 21396642 replaced by 20967831

MI20-09

Service Bulletin/Repair Instructions

PREVOST VEHICLE DISINFECTION PROCEDURE

MI20-08

Service Bulletin/Repair Instructions

STORAGE AND STARTUP GUIDELINES - ALL PREVOST VEHICLES & VOLVO 9700

MI15-24

Service Bulletin/Repair Instructions

Added: Power cables for L.H. side alternator & fan drive breaker box

FUELFILTER

Service Bulletin/Repair Instructions

Repair instructions to address fault codes P008A-00; P0087-00

NOX_Conv1

Service Bulletin/Repair Instructions

Repair instructions to address fault codes P207F-00 - Reductant Quality

NOx_Conv2

Service Bulletin/Repair Instructions

Repair instructions to address fault codes P207F-00; P20EE-00

IS-17071A

Service Bulletin/Repair Instructions

This instruction sheet explains how to install an ELD interface on OBD vehicles

IS-18910

Service Bulletin/Repair Instructions

This instruction sheet explains how to install a flap over the diesel filling cap

IS-13009D

Service Bulletin/Repair Instructions

This instruction sheet explains how to install and adjust drag link # 660699

IS-13009C

Service Bulletin/Repair Instructions

This instruction sheet explains how to install and adjust drag link # 660699

WB18-04

Service Bulletin/Repair Instructions

On the vehicles affected by this bulletin, update EMS and ACM software to the latest version available.

MI18-21A

Service Bulletin/Repair Instructions

This Maintenance Information presents information about the Bitzer A/C compressor oil change interval and reminds technicians to clean the oil filter/strainer and the magnetic drain plug.

IS-15003E

Service Bulletin/Repair Instructions

This insruction Sheet explains how to insall the Bosch HD10 24v-150a Alternator Conversion Kit ? Twin Bosch Mounted On Volvo D13 Engine

MI16-17G

Service Bulletin/Repair Instructions

This Maintenance Information explains how to remove and install the Bosch HD10 (120A or 150A) alternators

MI18-18A

Service Bulletin/Repair Instructions

This maintenance information explains how to tow and hoist Prevost vehicles.

MI18-18

Service Bulletin/Repair Instructions

This maintenance information explains how to tow and hoist Prevost vehicles.

MI18-16A

Service Bulletin/Repair Instructions

This Maintenance Information presents guidelines to help with the diagnosis of the Bosch HD10 alternators

MI18-21

Service Bulletin/Repair Instructions

This Maintenance Information presents information about the Bitzer A/C compressor oil change interval and reminds technicians to clean the oil filter/strainer and the magnetic drain plug.

MI18-02

Service Bulletin/Repair Instructions

This Mainteannce Informaiton presents the latest engine oil & filter change intervals for the Volvo Engine

Wb15-48A

Service Bulletin/Repair Instructions

This bulletin explains how to add a reinforcement bracket to Bitzer A/C compressor to increase the installation stiffness and reduce vibration amplitude.

MI16-17F

Service Bulletin/Repair Instructions

This Maintenance Information explains how to remove and install the Bosch HD10 (120A or 150A) alternators

WB15-19H

Service Bulletin/Repair Instructions

This bulletin explains how to add a reinforcement bracket to Bitzer A/C compressor to increase the installation stiffness and reduce vibration amplitude.

IS-17905

Service Bulletin/Repair Instructions

This instruction sheet explains how to install an ELD interface kit on Pre-OBD Prevost Vehicles equipped with Volvo D13 Engines

IS-13009B

Service Bulletin/Repair Instructions

This instruction sheet explains how to install and adjust drag link # 660699

MI17-22

Service Bulletin/Repair Instructions

This Maintenance Information explains how to inspect the Fuel Tank Cradle Mounting Screws on a yearly basis

IS-17071

Service Bulletin/Repair Instructions

This instruction sheet explains how to install an ELD interface on OBD vehicles

IS-17907

Service Bulletin/Repair Instructions

This instruction sheet explains how to install the Volvo Electronic Logging Device (ELD)

CK17-27

Service Bulletin/Repair Instructions

This conversion kit explains how to to disable the ACB radar.

IS-15003D

Service Bulletin/Repair Instructions

This insruction Sheet explains how to insall the Bosch HD10 24v-150a Alternator Conversion Kit ? Twin Bosch Mounted On Volvo D13 Engine

WB17-02

Service Bulletin/Repair Instructions

This bulletin explains how install an extension to the linear thermal detector (LTD) over the alternators

MI16-17D

Service Bulletin/Repair Instructions

Use this procedure for the removal and installation of the twin Bosch HD10 (120A or 150A) Alternators.

IS-15003B

Service Bulletin/Repair Instructions

This instruction sheet explains how to use the Bosch HD10 24V-150A Alternator Conversion Kit

MI16-15B

Service Bulletin/Repair Instructions

The Beru sensors used on Prevost vehicles to monitor tire pressure (TPMS system) are being replaced by new Huf sensors and their corresponding stainless valves stems. Since the older and newer sensors are using different valve stems, replacement of a defective sensor on older vehicles will require the use of a new kit number (valve stem and sensor assembly). The table below provides a quick overview between the older and newer part numbers depending on wheel application.

Wb16-29

Service Bulletin/Repair Instructions

On the vehicles affected by this bulletin, update EMS and ACM software to the latest version available. This update must be carried out by qualified technicians. As soon as possible, make an appointment with your nearest Prevost Service Center or contact your service manager to carry out the update.

MI16-23

Service Bulletin/Repair Instructions

This Maintenance Information explains that decals are available to update the front junction box on 2013 to 2016 Prevost vehicles; the decals will provide updated information and component descriptions. Refer to the identification part of this bulletin to locate the decal part number currently used on specific vehicles.

MI16-10

Service Bulletin/Repair Instructions

This information letter applies only to vehicles equipped with 19000 lb Independent Front Suspension (IFS) and 22.5 x 10.5 Alcoa aluminum wheels for 365/70 R 22.5 size tires. When balancing this wheel for installation on the IFS, a specific type and size of clamp-on wheel weight should be used to provide the appropriate clearance with components of the suspension.

MI16-15A

Service Bulletin/Repair Instructions

The Beru sensors used on Prevost vehicles to monitor tire pressure (TPMS system) are being replaced by new Huf sensors and their corresponding stainless valves stems. Since the older and newer sensors are using different valve stems, replacement of a defective sensor on older vehicles will require the use of a new kit number (valve stem and sensor assembly). The table below provides a quick overview between the older and newer part numbers depending on wheel application.

Wb15-19F

Service Bulletin/Repair Instructions

On the vehicles affected by this bulletin, vibration is causing damage to A/C compressor and compressor harness connectors. Addition of a reinforcement bracket to Bitzer A/C compressor is needed to increase the installation stiffness and reduce vibration amplitude.

Mi16-15

Service Bulletin/Repair Instructions

The Beru sensors used on Prevost vehicles to monitor tire pressure (TPMS system) are being replaced by new Huf sensors and their corresponding stainless valves stems. Since the older and newer sensors are using different valve stems, replacement of a defective sensor on older vehicles will require the use of a new kit number (valve stem and sensor assembly). The table below provides a quick overview between the older and newer part numbers depending on wheel application.

MI16-16

Service Bulletin/Repair Instructions

This procedure explains how to perform a STARTER REMOVAL AND INSTALLATION, and does apply to Melco 105P70 starter part number #21212425.

MI16-05

Service Bulletin/Repair Instructions

This Maintenance Information shares information about the Bendix M-32QR valve replaced by M-40QR model htat need to be taken into consideration, specially when switching them for the first time on a vehicle.

WB15-48

Service Bulletin/Repair Instructions

On the vehicles affected by this bulletin, vibration is causing damage to A/C compressor and compressor harness connectors. Addition of a reinforcement bracket to Bitzer A/C compressor is needed to increase the installation stiffness and reduce vibration amplitude.

WB15-19E

Service Bulletin/Repair Instructions

On the vehicles affected by this bulletin, vibration is causing damage to A/C compressor and compressor harness connectors. Addition of a reinforcement bracket to Bitzer A/C compressor is needed to increase the installation stiffness and reduce vibration amplitude.

SP15-60

Service Bulletin/Repair Instructions

On the vehicles affected by this bulletin, there is a contact possibility between some parts of the IFS suspension components and steering linkage when the wheels are rotated to their maximum left or right position and the suspension is fully extended or lowered. Consequently, the Prevost engineering department is requesting an inspection on about 15 vehicles (built between September 2013 and December 2014) equipped with the 19000lbs IFS suspension to have a clear picture of the vehicles out in the field and identify necessary actions to be taken.

WB15-50

Service Bulletin/Repair Instructions

On the vehicles affected by this bulletin the rear junction box decal located in the right engine compartment is displaying incorrect information regarding the R34 relay voltage. Specifically, the R34 relay should be identified as a 24 volt relay instead of a 12 volt relay. Consequently, all affected vehicles must have a small decal displaying the correct information applied over the rear junction box decal R34 relay description.

IS-15907A

Service Bulletin/Repair Instructions

This Instruction Sheet explains how to assemble the BENDIX FLR10 AND FLR20 RADAR SENSOR ALIGNMENT TOOL

MI15-41

Service Bulletin/Repair Instructions

This Maintenance Information reminds Prevost customers that cleaning products designed for external washing of vehicles should be used for exterior vehicle wash and in particular, for the washing of polycarbonate taillights.

MI15-43

Service Bulletin/Repair Instructions

New aramid cord poly-v belts are now available to replace the polyester cord alternator belts previously used on Prevost vehicles equipped with Bosch HD10 alternators.

WB15-19

Service Bulletin/Repair Instructions

On the vehicles affected by this bulletin, vibration is causing damage to A/C compressor and compressor harness connectors. Addition of a reinforcement bracket to Bitzer A/C compressor is needed to increase the installation stiffness and reduce vibration amplitude.

WB15-10A

Service Bulletin/Repair Instructions

On the vehicles affected by this bulletin, inspect the lower oil fill tube flexible tube. If it is made of black material (EDPM), replace tube. Green and blue silicone hoses are accepted.

MI15-18

Service Bulletin/Repair Instructions

This Maintenance Information does explain how five year old vehicles and older should be subjected to a thorough structural inspection.

WB15-10

Service Bulletin/Repair Instructions

On the vehicles affected by this bulletin, inspect the lower oil fill tube flexible tube. If it is made of black material (EDPM), replace tube. Green and blue silicone hoses are accepted.

IS-15003A

Service Bulletin/Repair Instructions

This instruction sheet explains how to use the Bosch HD10 24V-150A Altenrator Conversion Kit

IS-13169A

Service Bulletin/Repair Instructions

This Instruction Sheet explains how to install the AWARE ADAPTIVE CRUISE BRAKING (ACB) FLR20 RADAR SENSOR REPLACEMENT kits # 145372 and 145373

IS-13106

Service Bulletin/Repair Instructions

This instruction sheet explains how to install an improved version of the slide-out rails. This version of the rails offers better corrosion resistance.

WB14-47B

Service Bulletin/Repair Instructions

On the vehicles affected by this bulletin, perform a software update of ECM (Engine Control Module) and ACM (Aftertreatment Control Module) to provide improved temperature-related behaviour. The software will also change urea dosing valve behavior at shutdown and key-on. As an additional improvement, replace the urea dosing valve by an improved design. These hardware and software improvements aim to reduce the occurrence of clogging and shorting of the Urea Dosing Valve.

WB14-08C

Service Bulletin/Repair Instructions

On the vehicles affected by this bulletin, verify the revision numbers of the steering wheel gateway module and multiplex software. If applicable, replace with the latest version. A power source improvement is also required. On some vehicles, as a temporary measure, a switch was installed on the left dashboard for cruise control SET and RESUME. This installation must be removed to restore these controls to the steering wheel.

WB14-06G

Service Bulletin/Repair Instructions

On the vehicles affected by this bulletin, perform the following verifications and modifications on the A/C system: Bulletin is divided in five steps, refer to detailed instructions below. STEP 1: Unloader replacement (Step moved to Warranty Bulletin WB15-19) STEP 2: System vacuum, wiring update, remote pressure transducer and switch installation. STEP 3: Seal the evaporator compartment ventilation discharge duct. STEP 4: Check Evaporator expansion valve bulb position and MUX software version. STEP 5: Dynamic A/C system test to confirm all functions operate correctly.

WB14-28E

Service Bulletin/Repair Instructions

On the vehicles affected by this bulletin, replace the LTD, relocate and replace the IR sensor as described in the following procedure.

SP14-30

Service Bulletin/Repair Instructions

On the identified drive axles, the wheel nut may not be secured by the locking Tab.

SP14-29

Service Bulletin/Repair Instructions

On the engine?s right side, check that the alternators are connected right.

IS11015B

Service Bulletin/Repair Instructions

This Instruction Sheet explains how to replace power relay p/n 561991 with improved power relay p/n 564218 and relay base p/n 564210

Reading this report

Complaint counts are reports filed with NHTSA, not failure rates. A common model collects more of them than a rare one that breaks more often.