MI16-32
Service Bulletin/Repair Instructions
Improved bearings are now available to replace the original bearings used on some Prevost vehicles idler pulleys.
Vehicle report
Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
MI16-32
Improved bearings are now available to replace the original bearings used on some Prevost vehicles idler pulleys.
IS-19912E
ELECTRIC FAN DRIVE COOLING SYSTEM CONVERSION WITH DELCO REMY ALTERNATOR. REVISION: E Note added regarding power cable connection
IS-21072B
STEERING GATEWAY. Revision B - PIN 2 and 10 were inverted on connector A139
MI22-12B
Air Tanks Draining Sequence. Revision: B - General Update
MI22-12A
Air Tanks Draining Sequence. Revision: A - Erroneous Secondary & Accessory tanks location.
SP18-35J
P20EE (diagnostic troubleshooting code) SOLUTION - NOX CONVERSION EFFICIENCY. Revision J - Range of applicable VINs updated.
MI22-12
Air Tanks Draining Sequence
IS-17151C
Halogen to LED fog light replacement kit. Revision: C - Advanced kits canceled
IS-22902
TAG AXLE HUB FLANGE - ALTERNATE CAP SCREW
IS21-072
STEERING GATEWAY, revision A : Cancel watch dog removal from EFD part of the instruction
MI20-08C
STORAGE AND STARTUP GUIDELINES : part number updates
IS21-072A
STEERING GATEWAY Revision A Cancel watch dog removal from EFD part of the instruction
IS21-901
X3 SERIES ENVIROCARE - IONS AIR SANITIZER
IS20-925A
CENTRAL HVAC MERV FILTERS INSTALLATION
IS22-040
BRAKE PEDAL SEAL PLATE INSTALLATION KIT
SP18-39D
SCR CONVERTER REPLACEMENT - AFTERTREATMENT SYSTEM
SP18-35H
P20EE (diagnostic troubleshooting code) SOLUTION - NOX CONVERSION EFFICIENCY
MI18-16B
BOSCH HD10 ALTERNATOR DIAGNOSTIC GUIDE Revision B To avoid replacement of alternators that are in fact in good working order, perform the steps which follow to help you perform a more precise diagnosis.
SR19-31C
ENGINE CONTROL MODULE (ECM) SOFTWARE UPDATE - Engine Cooling Strategy in High Altitude Operation Revision C: VIN range in application box rearranged for H3 coaches
MI21-06
Diesel Exhaust Fluid ( DEF ) Contamination In Fuel System, Inspection And Repair â From US10 to newer engine generation
Mi21-07A
RONT & TAG AXLE â UNITIZED HUB BEARING END PLAY VERIFICATION AND REPLACEMENT
SP18-35F
P20EE (diagnostic troubleshooting code) SOLUTION - NOX CONVERSION EFFICIENCY Rev E: expiration date removed
IS-20925A
CENTRAL HVAC MERV FILTERS INSTALLATION REVA
MI20-19B
INTRODUCING A NEW ENGINE COOLANT INTO PREVOST SERVICE CENTER NETWORK
MI20-19A
Rev A: Mention added concerning DDC Series 60 engine SCA requirement
MI21-01
VOLVO I-SHIFT TRANSMISSION REPLACEMENT - DIFFERENCE BETWEEN CONNECTIONS AT THE TOP OF THE OIL FILTER HOUSING
MI20-19
INTRODUCING A NEW ENGINE COOLANT INTO SERVICE
MI20-12
JERKY, NOISY OR HARD TO TURN STEERING GEARBOX. HYDRAULIC END LIMITER ADJUSTMENT. All models â equipped with RB Bosch/ZF Servocom or Servocomtronic steering gearbox
MI18-18B
GENERAL HOISTING AND TOWING PROCEDURES Revision: B Updated 2.1 to show rubber chocks, secure front and rear.
MI20-08A
STORAGE AND STARTUP GUIDELINES: Rev A: 21516229 replaced by 23381562 20523393 replaced by 21454749 800383 removed 611471 replaced by 611360 70376808 replaced by 21036050 21396642 replaced by 20967831
MI20-09
PREVOST VEHICLE DISINFECTION PROCEDURE
MI20-08
STORAGE AND STARTUP GUIDELINES - ALL PREVOST VEHICLES & VOLVO 9700
MI15-24
Added: Power cables for L.H. side alternator & fan drive breaker box
FUELFILTER
Repair instructions to address fault codes P008A-00; P0087-00
NOX_Conv1
Repair instructions to address fault codes P207F-00 - Reductant Quality
NOx_Conv2
Repair instructions to address fault codes P207F-00; P20EE-00
SCI19-20
On the vehicles affected by this bulletin, the vehicle program has to be upgraded. This allows the Intelligent Sleep Mode (ISM) system improvement to prevent batteries drain when ISM is enabled. This procedure shows how to generate the Vehicle Program last update and how to transfer the program to the vehicle owner. Refer to bulletin WB19-11 for the upgrade procedure.
Wb19-11
On the vehicles affected by this bulletin, the vehicle program might need to be upgraded to prevent batteries drain when ISM (Intelligent Sleep Mode) is enabled.
WB19-07
On the independent front suspension (IFS) of the vehicles affected by this bulletin, check and make sure that there is enough clearance between the brake hoses identified in the procedure and their respective support bracket.
SP18-35B_English
On vehicles with active code P20EE, perform the following checklist and operations.
IS-17071A
This instruction sheet explains how to install an ELD interface on OBD vehicles
IS-18910
This instruction sheet explains how to install a flap over the diesel filling cap
MI19-06
This Maintenance Information is published to answer some questions regarding the inverted or ?trailing? mounting position of the drive axle brake calipers on Prevost vehicles
Sp18-35
On vehicles with active code P20EE, perform the following checklist and operations.
WB18-04
On the vehicles affected by this bulletin, update EMS and ACM software to the latest version available.
MI18-21A
This Maintenance Information presents information about the Bitzer A/C compressor oil change interval and reminds technicians to clean the oil filter/strainer and the magnetic drain plug.
MI16-17G
This Maintenance Information explains how to remove and install the Bosch HD10 (120A or 150A) alternators
MI18-18A
This maintenance information explains how to tow and hoist Prevost vehicles.
MI18-37
This Maintenance Information presents information about the removal or installation of the Lang KK73.1 electromagnetic clutch - part of the Bitzer (model 4NFCY) air conditioning compressor.
IS-18901
This instruction sheet explains how to install the engine belt guard on X3 Series vehicles with coolant system electrical fan drive.
MI18-18
This maintenance information explains how to tow and hoist Prevost vehicles.
MI18-16A
This Maintenance Information presents guidelines to help with the diagnosis of the Bosch HD10 alternators
MI18-21
This Maintenance Information presents information about the Bitzer A/C compressor oil change interval and reminds technicians to clean the oil filter/strainer and the magnetic drain plug.
MI18-02
This Mainteannce Informaiton presents the latest engine oil & filter change intervals for the Volvo Engine
MI16-17F
This Maintenance Information explains how to remove and install the Bosch HD10 (120A or 150A) alternators
IS-17905
This instruction sheet explains how to install an ELD interface kit on Pre-OBD Prevost Vehicles equipped with Volvo D13 Engines
IS-13009B
This instruction sheet explains how to install and adjust drag link # 660699
IS-17016
This instruciton sheet explains how to relocate the RV-3 Valve
MI17-22
This Maintenance Information explains how to inspect the Fuel Tank Cradle Mounting Screws on a yearly basis
IS-17071
This instruction sheet explains how to install an ELD interface on OBD vehicles
IS-17907
This instruction sheet explains how to install the Volvo Electronic Logging Device (ELD)
CK17-30
On the vehicles affected by this bulletin, it is now possible to replace the older generation TGW 2.0 (3G network) by the newer 2.1 version (4G the network) using accessory kit 23266301 and the following procedure.
CK17-27
This conversion kit explains how to to disable the ACB radar.
SP17-18
On the vehicles affected by this bulletin, remove relay R26, isolate and/or reconnect wires according to the wiring diagram D061670 P18.2 revision 8. Also move water pump ground connection to the electronic ground pin A54 J2.14 and rename circuit gnd-0EVAP2-14.
Wb17-10A
On the vehicles affected by this bulletin, inspect and re-torque the Prevost slide-out rail bolts. If damaged, replace bolts.
WB17-02
This bulletin explains how install an extension to the linear thermal detector (LTD) over the alternators
MI16-17E
This Maintenance Information explains how to remove and install the Bosch HD10 (120A or 150A) alternator.
MI16-10A
This maintenance information applies only to vehicles equipped with 19000 lb Independent Front Suspension (IFS) and 22.5 x 10.5 Alcoa aluminum wheels for 365/70 R 22.5 size tires. When balancing this wheel for installation on the IFS, a specific type and size of clamp-on wheel weight should be used to provide the appropriate clearance with components of the suspension.
MI16-15B
The Beru sensors used on Prevost vehicles to monitor tire pressure (TPMS system) are being replaced by new Huf sensors and their corresponding stainless valves stems. Since the older and newer sensors are using different valve stems, replacement of a defective sensor on older vehicles will require the use of a new kit number (valve stem and sensor assembly). The table below provides a quick overview between the older and newer part numbers depending on wheel application.
MI16-15A
The Beru sensors used on Prevost vehicles to monitor tire pressure (TPMS system) are being replaced by new Huf sensors and their corresponding stainless valves stems. Since the older and newer sensors are using different valve stems, replacement of a defective sensor on older vehicles will require the use of a new kit number (valve stem and sensor assembly). The table below provides a quick overview between the older and newer part numbers depending on wheel application.
Mi16-15
The Beru sensors used on Prevost vehicles to monitor tire pressure (TPMS system) are being replaced by new Huf sensors and their corresponding stainless valves stems. Since the older and newer sensors are using different valve stems, replacement of a defective sensor on older vehicles will require the use of a new kit number (valve stem and sensor assembly). The table below provides a quick overview between the older and newer part numbers depending on wheel application.
MI16-16
This procedure explains how to perform a STARTER REMOVAL AND INSTALLATION, and does apply to Melco 105P70 starter part number #21212425.
MI16-05
This Maintenance Information shares information about the Bendix M-32QR valve replaced by M-40QR model htat need to be taken into consideration, specially when switching them for the first time on a vehicle.
IS-15907A
This Instruction Sheet explains how to assemble the BENDIX FLR10 AND FLR20 RADAR SENSOR ALIGNMENT TOOL
IS-13169A
This Instruction Sheet explains how to install the AWARE ADAPTIVE CRUISE BRAKING (ACB) FLR20 RADAR SENSOR REPLACEMENT kits # 145372 and 145373
IS-13169
This Instruction Sheet explains how to install the AWARE ADAPTIVE CRUISE BRAKING (ACB) FLR20 RADAR SENSOR REPLACEMENT kits # 145372 and 145373
Complaint counts are reports filed with NHTSA, not failure rates. A common model collects more of them than a rare one that breaks more often.