Vehicle report
Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
MI26-00
The gasket thickness was increased from 1.5 mm to 3 mm to prevent interference between the collar ends, which previously made it impossible to reach the specified tightening torque. Increasing the gasket thickness ensures sufficient clearance between the collar ends and thus guarantees optimal tightening.
IS-23019A
Sway bar collars improvement. Revision A : Add front sway bar support replacement and change bolts lenght.
IS-23019
SWAY BAR COLLARS IMPROVEMENT
MI16-32
Improved bearings are now available to replace the original bearings used on some Prevost vehicles idler pulleys.
IS-21072B
STEERING GATEWAY. Revision B - PIN 2 and 10 were inverted on connector A139
MI22-12B
Air Tanks Draining Sequence. Revision: B - General Update
MI22-12A
Air Tanks Draining Sequence. Revision: A - Erroneous Secondary & Accessory tanks location.
MI22-12
Air Tanks Draining Sequence
IS-22902
TAG AXLE HUB FLANGE - ALTERNATE CAP SCREW
IS21-072
STEERING GATEWAY, revision A : Cancel watch dog removal from EFD part of the instruction
MI20-08C
STORAGE AND STARTUP GUIDELINES : part number updates
IS21-072A
STEERING GATEWAY Revision A Cancel watch dog removal from EFD part of the instruction
IS21-901
X3 SERIES ENVIROCARE - IONS AIR SANITIZER
IS20-925A
CENTRAL HVAC MERV FILTERS INSTALLATION
IS22-040
BRAKE PEDAL SEAL PLATE INSTALLATION KIT
MI18-16B
BOSCH HD10 ALTERNATOR DIAGNOSTIC GUIDE Revision B To avoid replacement of alternators that are in fact in good working order, perform the steps which follow to help you perform a more precise diagnosis.
MI21-06
Diesel Exhaust Fluid ( DEF ) Contamination In Fuel System, Inspection And Repair â From US10 to newer engine generation
IS-18091A
TIE ROD 610052 FIRST INSTALLATION INSTRUCTIONS: Use these instructions when replacing the drop joint tie rod on S82, S84 / S84U I-beam axles. The new tie rod will be adjusted to the length of the original; however, a steering alignment needs to be performed after replacement.
MI20-19B
INTRODUCING A NEW ENGINE COOLANT INTO PREVOST SERVICE CENTER NETWORK
MI20-19A
Rev A: Mention added concerning DDC Series 60 engine SCA requirement
MI21-01
VOLVO I-SHIFT TRANSMISSION REPLACEMENT - DIFFERENCE BETWEEN CONNECTIONS AT THE TOP OF THE OIL FILTER HOUSING
MI20-19
INTRODUCING A NEW ENGINE COOLANT INTO SERVICE
MI20-08B
STORAGE AND STARTUP GUIDELINES Revision: B Parts added to Suggested Material 08-10-2020
MI20-12
JERKY, NOISY OR HARD TO TURN STEERING GEARBOX. HYDRAULIC END LIMITER ADJUSTMENT. All models â equipped with RB Bosch/ZF Servocom or Servocomtronic steering gearbox
MI18-18B
GENERAL HOISTING AND TOWING PROCEDURES Revision: B Updated 2.1 to show rubber chocks, secure front and rear.
MI20-08A
STORAGE AND STARTUP GUIDELINES: Rev A: 21516229 replaced by 23381562 20523393 replaced by 21454749 800383 removed 611471 replaced by 611360 70376808 replaced by 21036050 21396642 replaced by 20967831
MI20-09
PREVOST VEHICLE DISINFECTION PROCEDURE
MI20-08
STORAGE AND STARTUP GUIDELINES - ALL PREVOST VEHICLES & VOLVO 9700
MI15-24
Added: Power cables for L.H. side alternator & fan drive breaker box
FUELFILTER
Repair instructions to address fault codes P008A-00; P0087-00
NOX_Conv1
Repair instructions to address fault codes P207F-00 - Reductant Quality
NOx_Conv2
Repair instructions to address fault codes P207F-00; P20EE-00
Complaint counts are reports filed with NHTSA, not failure rates. A common model collects more of them than a rare one that breaks more often.