Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
9100898
Service Bulletin/Repair Instructions
Engine PNs: MY 24-26 WD/DT (5.7L) Code P00B is being misdiagnosed and incorrect parts are being installed causing over repair. Refer to SOL S2609000006 The IAFM Foam Engine Valley Cover (PN 53013735AB) does not provide sufficient clearance for proper routing of the MDS solenoid jumper harness (PN 05148163AE). As a result, the harness may become compressed by the foam cover. To prevent unnecessary part replacement, the MDS solenoid jumper harness (PN 05148163AE) should be inspected for damage or pinch conditions prior to replacing the following part numbers: Engine PNs: 68409343AA 68409357AA 68450915AA OCV PNs: 53022338AB Phaser PNs: 53022298AA 53022298AB
9100892
Service Bulletin/Repair Instructions
Switch - Tailgate Handle Prior to replacing the Tailgate Handle Switch, please review MasterTech Article - Tailgate Handle Inoperative.
113854
Service Bulletin/Repair Instructions
SWITCH AND BEZEL - FRONT DOOR
113855
Service Bulletin/Repair Instructions
SWITCH AND BEZEL - FRONT DOOR
114072
Service Bulletin/Repair Instructions
MOTOR - WINDOW REGULATOR
114073
Service Bulletin/Repair Instructions
MOTOR - WINDOW REGULATOR
9100274 Rev 1
Service Bulletin/Repair Instructions
Blindspot Module For concern on Blindspot Module setting U11FB-00 Lost Communication with Left Blind Spot Sensor, U11FA-00 Lost Communication with Right Blind Spot Sensor. Some vehicle(s) where the Blindspot Module was replaced had no issues found with the Blindspot Module after testing. Please verify no wiring or connector issues are present prior to module replacement.
08-291-26
Service Bulletin/Repair Instructions
R1H UBQ/UEQ Intermittent HVAC Page Lockup Customers may experience one or more of the following: SYMPTOM: ● Intermittently the HVAC page on the Display Screen Module will change temperature and blower speed and then freeze. ● When on the HVAC page, the Display Screen Module may not respond to touch. All other pages operate as intended.
08-288-26
Service Bulletin/Repair Instructions
Radio Does Not Display Selected Drive Mode Customers may experience the following: SYMPTOM: ● Drive Mode setting reverts back to "Auto" on Display Screen Module while the Instrument Panel Cluster (IPC) shows the Drive Mode that has been requested.
S2608000033
Service Bulletin/Repair Instructions
Cluster Message “To Operate Tailgate Shift to Park” Vehicle is In Park
08-270-26
Service Bulletin/Repair Instructions
Uconnect® Screen Image Changes Size, Customers may experience the following: SYMPTOM: ● The Uconnect® screen image changes size, moves or is out of place unprompted.
21-055-26
Service Bulletin/Repair Instructions
Flash: Transmission Control Module (TCM) Updates Customers may comment on one or more of the following: SYMPTOM: ● Harsh or slipping feeling during upshifts (1st - 5th). ● Harsh or slipping feeling during kickdown events under throttle. ● Transmission fluid odor (burnt smell). This bulletin involves reprogramming the TCM with the latest available software.
08-268-26
Service Bulletin/Repair Instructions
SXM Radio Doesn't Reflect Station Or Song Changing Customers may experience the following: SYMPTOM: ● When playing SXM stations the radio does not reflect the current station or recognize a song changing.
113276
Service Bulletin/Repair Instructions
CORE – HEATER
113277
Service Bulletin/Repair Instructions
CORE – HEATER
9100833 REV1
Service Bulletin/Repair Instructions
Fuel Delivery Module Before replacing the fuel module for DTCs P0461 and P062A and other not start, long crank, fuel gauge accuracy and drivability issues, the technician should disconnect the electrical connector at the pump and perform a visual inspection of the connector for and bent, spread, or pushed out terminals. Repair any issues found. Reconnect the plug and perform a push pull push to ensure the connector is fully installed. Then perform 3 keys cycles and listen to hear if the fuel pump is operational. If the fuel pump is heard that indicates that everything is operating correctly. If the pump is heard replacement is not necessary, any replacement will function in the same way.
S2508000025 REV. B
Service Bulletin/Repair Instructions
Instrument Panel Cluster (IPC) and Radio Compass Display has Dashes (--)
113069
Service Bulletin/Repair Instructions
SWITCH – HEADLAMP
113070
Service Bulletin/Repair Instructions
SWITCH – HEADLAMP
113123
Service Bulletin/Repair Instructions
SPRING KIT - DISC BRAKE PAD
S2208000045 REV.D
Service Bulletin/Repair Instructions
Backup Camera Poor Image Quality Inspection
S2508000025 REV.A
Service Bulletin/Repair Instructions
Instrument Panel Cluster (IPC) and Radio Compass Display has Dashes (--)
S2623000047
Service Bulletin/Repair Instructions
Blind Spot Alert Trailer Type Conventional Goose / 5th Displays On Cluster. Cannot Select Trailer Type.
113065
Service Bulletin/Repair Instructions
OUTLET - AIR CONDITIONING & HEATER
113066
Service Bulletin/Repair Instructions
OUTLET - AIR CONDITIONING & HEATER
9100833
Service Bulletin/Repair Instructions
Fuel Delivery Module Before replacing the fuel module for DTCs P0461 and P062A and other not start, long crank, fuel gauge accuracy and drivability issues, the technician should disconnect the electrical connector at the pump and perform a visual inspection of the connector for and bent, spread, or pushed out terminals. Repair any issues found. Reconnect the plug and perform a push pull push to ensure the connector is fully installed. Then perform 3 keys cycles and listen to hear if the fuel pump is operational. If the fuel pump is heard that indicates that everything is operating correctly. If the pump is heard replacement is not necessary, any replacement will function in the same way.
9100845
Service Bulletin/Repair Instructions
For concerns of an inoperative A/C system (no relay activation, no compressor engagement, or no response to commands), technicians need to utilize Star Online Publication S2624000007 prior to component replacement. Failure to follow this star online publication may result in repeat repairs or misdiagnosis.
S268A000014
Service Bulletin/Repair Instructions
Radio/ETM is Adding Approximately 27mA Draw to Vehicle When in Logistics Mode
S1623000028 Rev. K
Service Bulletin/Repair Instructions
Outside Power Fold Rearview Mirror Noise Or Loose At Pivot. Mirror Contacts Door Window Glass In The Folded Position.
112651
Service Bulletin/Repair Instructions
SHOCK ABSORBER - SUSPENSION
112652
Service Bulletin/Repair Instructions
SHOCK ABSORBER - SUSPENSION
9100839
Service Bulletin/Repair Instructions
3-way valves are available in STAR Parts as two distinct components and must be selected correctly based on application. The High Temp 3-way valve (68309834AC) is located between the engine and the bulkhead at the rear of the engine compartment. The Low Temp 3-way valve (68448241AA) is located between the engine and the radiator at the front of the engine. When ordering or servicing, ensure the correct valve is identified and installed in the proper location, as incorrect part selection may lead to improper thermal system operation and repeat repairs.
S1623000028 REV.J
Service Bulletin/Repair Instructions
Outside Power Fold Rearview Mirror Noise Or Loose At Pivot. Mirror Contacts Door Window Glass In The Folded Position.
9100831
Service Bulletin/Repair Instructions
For Dealer awareness, HD truck, eliminate 1 of 2 M8 Joints for Sidestep bracket to Body Attachment, Bolt and rivet (06102165AA, 06511062AA) per TCR # 402632, CN 80403-T18
112633
Service Bulletin/Repair Instructions
HANDLE - DOOR PULL and PANEL - FRONT DOOR TRIM
112634
Service Bulletin/Repair Instructions
HANDLE - DOOR PULL and PANEL - FRONT DOOR TRIM
111785
Service Bulletin/Repair Instructions
MODULE - CENTRAL ADAS DECISION and DRIVER MONITORING
S1623000028 REV.I
Service Bulletin/Repair Instructions
Outside Power Fold Rearview Mirror Noise Or Loose At Pivot. Mirror Contacts Door Window Glass In The Folded Position.
S2408000018 REV.B
Service Bulletin/Repair Instructions
New Key Will Not Program, 0x22 Scan Tool Error
111846
Service Bulletin/Repair Instructions
AIR BAG - DRIVER
111847
Service Bulletin/Repair Instructions
AIR BAG - DRIVER
111751
Service Bulletin/Repair Instructions
GRILLE - SPEAKER
9100786 Rev 1
Service Bulletin/Repair Instructions
TBM2.0H Setting U0080-00. Do not replace TBM ECU or SGW. If replacement is determined, Verify "Z" part number availability. Order a "Z" part number for all Exchange Orders, Warranty, Mopar, Customer Pay and Service Contract. Order "68" part number for New, Unsold units only. Under certain conditions, SGW Module may take longer to establish Ethernet communication after boot up. If it takes longer than 30 seconds, The TBM2.0H module will set DTC U0080 - Ethernet Bus 1. As soon as SGW responds, the TBM2.0H will demature the DTC and move it to STORED. This issue should not cause any customer related symptoms. Do not replace the following TBM Part Numbers: WL: 68639445AF,68637489AE,68663479AE. WS: 68734941AA,68729188AC. EJ: 68592344AI. KM: 68592343AL,68735975AD. DT: 68634362AJ,68624784AF,68624784AE,68735493AB,68735493AA. DJ (HDCC): 68608721AJ. If the TBM2.0H module has set the DTC U0080 and it is STORED or ACTIVE, please clear the fault and do nothing. No further diagnostics is required. ---------------------------------------------------------------------------------------------------- TBM2.0H Setting DTC B1E21 Do Not Replace the TBM ECU. Is triggered when the TBM Backup Battery is discharged, inactive, or drained. This can happen during the lifetime of the vehicle. TBM should NOT be replace for B1E21, since there is no fault on TBM. TBM battery is replaceable. Part number of the back-up battery inside TBM is 68597650AA. Do not replace the following TBM Part Numbers: WL: 68639445A$, 68663479A$. -------------------------------------------------------------------------------------------------------- TBM Setting DTC U0499-00 Please refer to SOL S268A000004 if you are attempting to replace or repair the telematics box due to DTC U0499-00. This DTC does not cause direct customer impact and cannot be cleared. Engineering is working on TBM software enhancements, tentative Q2 2026. Do not replace the following TBM Part Numbers: KM: 68592343A$
08-208-26 REV. A
Service Bulletin/Repair Instructions
Radio Message "Power Surge On USB Detected" Customers may comment on the following: ● The radio displays the message: “Power surge on USB hub detected” Fig. 1. NOTE: After the message appears, no USB devices function in the hub (no charging, no data). NOTE: Hub operation does not return until the vehicle undergoes a full key cycle.
111830
Service Bulletin/Repair Instructions
SENSOR – KNOCK
111831
Service Bulletin/Repair Instructions
SENSOR – KNOCK
111833
Service Bulletin/Repair Instructions
SENSOR – KNOCK
111834
Service Bulletin/Repair Instructions
SENSOR – KNOCK
08-208-26
Service Bulletin/Repair Instructions
Radio Message "Power Surge On USB Detected" Customers may comment on the following: ● The radio displays the message: “Power surge on USB hub detected” Fig. 1. NOTE: After the message appears, no USB devices function in the hub (no charging, no data). NOTE: Hub operation does not return until the vehicle undergoes a full key cycle
08-207-26
Service Bulletin/Repair Instructions
Instrument Panel Cluster (IPC) Flicker Turn By Turn The customer may experience flickering on their Instrument Panel Cluster (IPC) when the turn-by-turn feature is enabled. This issue occurs when using Google Maps for Navigation via CarPlay
S268A000013
Service Bulletin/Repair Instructions
Radio Volume Jumping Up To Max Volume After Radio Wake Up
S2623000031
Service Bulletin/Repair Instructions
Active Damping Control Module (ADCM) Stored Diagnostic Trouble Codes (DTCs).
S2623000032
Service Bulletin/Repair Instructions
Squeak Or Squawk Noise Coming From Either Side Door Of The Vehicle, It Could Be Just One Door Or More. The Noise Can Be Present In Either The Upper Or The Lower Hinge.
S2308000034 REV.B
Service Bulletin/Repair Instructions
No Wireless Charging Or Slow Wireless Charging
S2609000006
Service Bulletin/Repair Instructions
P000B Bank 1 Cam 2 Position Slow Response - Malfunction Indicator Light (MIL) - Check Engine Light (CEL)
23-011-26
Service Bulletin/Repair Instructions
Power Tailgate Latch Will Not Open Or Close, Tailgate Ajar Light On When Tailgate Is Close Customers may experience one or more of the following: ● Power tailgate not opening or closing intermittently. ● Tailgate is hard to open or close. ● 'Tailgate Ajar' light on in the Instrument Panel Cluster (IPC) when the tailgate is closed. ● Diagnostic Trouble Code (DTC) stored for tailgate latch switches causing intermittent failure.
S2523000003 REV.A
Service Bulletin/Repair Instructions
Door Latch, Handle And Ajar Additional Service Information.
S2408000018 REV.A
Service Bulletin/Repair Instructions
New Key Will Not Program, 0x22 Scan Tool Error
9100799
Service Bulletin/Repair Instructions
WARNING: Shorting the 48V output stud to the 12V output stud can cause immediate and irreversible damage to the power pack unit. Always use insulated tools and protective stud covers when performing service operations. NOTE: A loose or high resistance ground connection may result in abnormal voltage behavior and can increase the risk of electrical component damage. Always verify ground integrity before system power up. For P0AFA repair: Please follow the Service library steps 1 through 7 without fail. Only replace PPU or MGU after verifying the final step of the procedure.
111396
Service Bulletin/Repair Instructions
COOLER - AUXILIARY LOW TEMPERATURE
111405
Service Bulletin/Repair Instructions
COVER - CYLINDER HEAD
111406
Service Bulletin/Repair Instructions
COVER - CYLINDER HEAD
111128
Service Bulletin/Repair Instructions
THERMOSTAT – NONE
111129
Service Bulletin/Repair Instructions
THERMOSTAT – NONE
9100702Rev1
Service Bulletin/Repair Instructions
Camshaft cap bolts within the cylinder head assembly may cause damage to other components. DO NOT replace entire long block when only left OR right cylinder heads need to be replaced.
9100793
Service Bulletin/Repair Instructions
Please review all wiring Connectors for latches between Latch and PTGM and Middle Connector to make sure they fully seated and Connectors are clipped in. No Latch to be replaced for stored DTCs. DTCs trigger due to loose connectors. Unplug and plug connectors back and clear DTCs and check the system.
08-143-26
Service Bulletin/Repair Instructions
Traffic Sign Assist Unavailable – Service Required The customer may experience one or more of the following: SYMPTOM: ● “Traffic Sign Assist Unavailable – Service Required” message and icon displays on the Instrument Panel Cluster (IPC). This occurs after a remote start and typically at the first start of the day. ● The Odometer flashes when the traffic alert message is active. . No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, electronic, mechanical, photocopying, or otherwise, without written permission of FCA US LLC.
S1623000028 REV.H
Service Bulletin/Repair Instructions
Outside Power Fold Rearview Mirror Noise Or Loose At Pivot. Mirror Contacts Door Window Glass In The Folded Position.
9100786
Service Bulletin/Repair Instructions
TBM2.0H Setting U0080-00. Do not replace TBM ECU or SGW. Under certain conditions, SGW Module may take longer to establish Ethernet communication after boot up. If it takes longer than 30 seconds, The TBM2.0H module will set DTC U0080 - Ethernet Bus 1. As soon as SGW responds, the TBM2.0H will demature the DTC and move it to STORED. This issue should not cause any customer related symptoms. Do not replace the following TBM Part Numbers: WL: 68639445AF,68637489AE,68663479AE. WS: 68734941AA,68729188AC. EJ: 68592344AI. KM: 68592343AL,68735975AD. DT: 68634362AJ,68624784AF,68624784AE,68735493AB,68735493AA. DJ (HDCC): 68608721AJ. If the TBM2.0H module has set the DTC U0080 and it is STORED or ACTIVE, please clear the fault and do nothing. No further diagnostics is required. ---------------------------------------------------------------------------------------------------- TBM2.0H Setting DTC B1E21 Do Not Replace the TBM ECU. Is triggered when the TBM Backup Battery is discharged, inactive, or drained. This can happen during the lifetime of the vehicle. TBM should NOT be replace for B1E21, since there is no fault on TBM. TBM battery is replaceable. Part number of the back-up battery inside TBM is 68597650AA. Do not replace the following TBM Part Numbers: WL: 68639445A$, 68663479A$. ---------------------------------------------------------------------------------------------------------- TBM Setting DTC U0499-00 Please refer to SOL S268A000004 if you are attempting to replace or repair the telematics box due to DTC U0499-00. This DTC does not cause direct customer impact and cannot be cleared. Engineering is working on TBM software enhancements, tentative Q2 2026. Do not replace the following TBM Part Numbers: KM: 68592343A$
08-134-26
Service Bulletin/Repair Instructions
Universal Garage Door Opener (UGDO) Inoperable Technicians may or may not find the following Diagnostic Trouble Code (DTC) present: SYMPTOM: ● B251D1-00 - Universal Garage Door Opener Control. Customers may comment on the following: ● Operational questions regarding the usage of the HomeLink® UGDO. . No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, electronic, mechanical, photocopying, or otherwise, without written permission of FCA US LLC.
18-044-26
Service Bulletin/Repair Instructions
Flash: Powertrain Control Module (PCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must SYMPTOM: exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● **P0111-00 - Intake Air Temperature Sensor 1 Circuit Range Performance Bank 1. (In Active or Stored status) ● P0071-00 - Ambient Air Temperature Sensor Performance. (In Active or Stored status) ● P0072-00 - Ambient Air Temperature Sensor Circuit "A" Low. (In Active or Stored status) ● P0073-00 - Ambient Air Temperature Sensor Circuit "A" High. (In Active or Stored status) ● P0011-00 - Bank 1 Camshaft 1 Position Timing Over Advanced Or. (In Active or Stored status) ● P25E4-00 - B Camshaft Position - Unable To Achieve Locked Position Bank 1. (In Active or Stored status) ● P05BD-00 - Stop-Start Mode Switch Range/Performance. (In Active or Stored status) ● P0116-00 - Engine Coolant Temperature Sensor 1 Performance. (In Active or Stored status) ● P062B-00 - Internal Control Module Fuel Injector Control Performance. (In Active or Stored status) ● P0604-00 - Internal Control Module Random Access Memory Ram Error. (In Active or Stored status) ● P060C-00 - Internal Control Module Main Processor Performance. (In Active or Stored status)** ● P018B-00 - Fuel Pressure Sensor "B" Circuit Range/performance. **(In Active or Stored status)** ● P1CEA-00 - Boost Side EVAP Purge System Performance. **(In Active or Stored status)** ● P06DD-00 - Engine Oil Pressure Control Circuit Performance/Stuck Off. **(In Active or Stored status)** ● P00C6-00 - Fuel Rail Pressure Too Low - Engine Cranking. **(In Active or Stored status)** ● P0300-00 - Multiple Cylinder Misfire. **(In Active or Stored status)** Customers may also experience one or more of the following: ● **Oil Level High Warning in the Instrument Panel Cluster (IPC).** ● Fully Autonomous Parking Assist (FAPA) is not deactivated when accelerator pedal is pressed. ● Vehicle is not heating up fast enough at freezi
S2208000045 REV.C
Service Bulletin/Repair Instructions
Backup Camera Poor Image Quality Inspection
S2523000070 REV.A
Service Bulletin/Repair Instructions
Central ADAS Decision Module (CADM) Diagnostic Trouble Codes C00C0-4A, C00C1-4A, C00C5-4A.
S2621000003 REV.A
Service Bulletin/Repair Instructions
The vehicle will exhibit a service transmission/check engine warning indicator for the following transmission models: 845RE, 8HP45, 850RE, 8HP50, 8HP70, 8HP75, 8HP75-PHEV, 8HP75-LCV, 8HP90, 8HP95. Transmissions may exhibit the following diagnostic codes: P07E4, P1DB2, P0716, P1B14, P0733, P1D90, P1DB7, P1B13.
S2623000012
Service Bulletin/Repair Instructions
Window Switch Feels Loose In The Door Trim Panel.
S2608000010
Service Bulletin/Repair Instructions
Active Diagnostic Trouble Code (DTC) B1A10-00, B1A11-00, B1A12- 00, B1A13-00-, B1A14-00, B1A15-00, B1A16-00, and B1A17-00 in The Radio Frequency Hub (RFH)
23-005-26
Service Bulletin/Repair Instructions
Windshield Wiper Blade Maintenance Customers may experience one or more of the following: SYMPTOM: ● Wiper blades that chatter/streak/jump/skip/smear or make noise while traveling across the windshield. . No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, electronic, mechanical, photocopying, or otherwise, without written permission of FCA US LLC.
S1408000384 REV.J
Service Bulletin/Repair Instructions
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
110599
Service Bulletin/Repair Instructions
SPEAKER - NONE
110600
Service Bulletin/Repair Instructions
SPEAKER - NONE
110603
Service Bulletin/Repair Instructions
SPEAKER - NONE
110604
Service Bulletin/Repair Instructions
SPEAKER - NONE
S2621000003
Service Bulletin/Repair Instructions
Service transmission/check engine warning indicator for the 850RE, 8HP50, 8HP70, 8HP75, 8HP75-PHEV transmissions that have fault codes P07E4, P1DB2, P0716, P1B14, P0733, P1D90, P1DB7, P1B13.
S268A000009
Service Bulletin/Repair Instructions
Customer States Navigation is Inaccurate, Showing Wrong City or State.
110463
Service Bulletin/Repair Instructions
SWITCH - TRAILER BRAKE CONTROL MODULE , ADAPTER & WIRING KIT - TRAILER TOW.
S228A000025 REV.A
Service Bulletin/Repair Instructions
Harman R1H Uconnect 5 Radio Software Flash Error Codes
S268A000008
Service Bulletin/Repair Instructions
Uconnect Box Requires Service, Please Visit an Authorized Dealer Message on Display Message With DTCs B1498-13, B1498-19 or B1570-93
S1923000010 REV.A
Service Bulletin/Repair Instructions
Floor Console Center Storage Bin Door Inoperable And Or Stuck Closed.
S2423000027 REV.D
Service Bulletin/Repair Instructions
Horn Sound Is Weak, Off Tone, Inoperative, Or Intermittent.
S268A000007
Service Bulletin/Repair Instructions
Navigation Is Active On The Radio But Not Available On The Cluster
9100591 Rev 1
Service Bulletin/Repair Instructions
Universal Garage Door Opener Prior to replacing the UGDO or sun visor, call HomeLink® Customer Care at 1-800-355-3515 for a proper evaluation of the issue. If this does not correct the issue, please follow the steps in SOL: S2508000039
9100767
Service Bulletin/Repair Instructions
Verify "Z" part number availability. Order a "Z" part number for all Exchange Orders, Warranty, Mopar, Customer Pay and Service Contract. Order "68" part number for New, Unsold units only.
S1408000384 REV.I
Service Bulletin/Repair Instructions
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS Related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
S268A000006
Service Bulletin/Repair Instructions
Hands-Free Voice Concerns Including No Voice Pickup, Muffled Audio, Distortion, or Intermittent Microphone Operation
S2623000006
Service Bulletin/Repair Instructions
Washer Fluid Warning Lamp Illuminated When Reservoir Is Full
110081
Service Bulletin/Repair Instructions
MODULE - TRAILER BRAKE & TOWING CONTROL
110082
Service Bulletin/Repair Instructions
MODULE - TRAILER BRAKE & TOWING CONTROL
S2308000120 REV.F
Service Bulletin/Repair Instructions
Rain Sensing Auto Wipers and Auto on Head Lamps Inoperative. Rain Sensor Internal Failure.
18-015-26
Service Bulletin/Repair Instructions
Flash: Powertrain Control Module (PCM) Updates Customers may experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle may exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): lP0300-00 - Multiple Cylinder Misfire - in Active or Stored status set during cold start catalyst heating. lP0301-00 - Cylinder 1 Misfire - in Active or Stored status set during cold start catalyst heating. lP0302-00 - Cylinder 2 Misfire - in Active or Stored status set during cold start catalyst heating. lP0303-00 - Cylinder 3 Misfire - in Active or Stored status set during cold start catalyst heating. lP0304-00 - Cylinder 4 Misfire - in Active or Stored status set during cold start catalyst heating. lP0305-00 - Cylinder 5 Misfire - in Active or Stored status set during cold start catalyst heating. lP0306-00 - Cylinder 6 Misfire - in Active or Stored status set during cold start catalyst heating. Customers may also comment on one or more of the following: lVehicle has a rough idle. lEngine has a miss. lNoisy valvetrain. This bulletin involves reprogramming the PCM with the latest available software.
S2607000002
Service Bulletin/Repair Instructions
Hemi Water Pump Coolant Leak Inspection
S2508000076 REV.A
Service Bulletin/Repair Instructions
Power Side Steps May Deploy and Retract While the Vehicle is in Motion
109724
Service Bulletin/Repair Instructions
Water Pump & Chain Case Cover
109727
Service Bulletin/Repair Instructions
Water Pump & Chain Case Cover
08-012-26
Service Bulletin/Repair Instructions
Speaker Diagnostic Procedure Rattle, buzz and squeak coming from specific speakers.
S2308000120 REV.E
Service Bulletin/Repair Instructions
Rain Sensing Auto Wipers and Auto on Head Lamps Inoperative. Rain Sensor Internal Failure.
109152
Service Bulletin/Repair Instructions
CORE – HEATER
109153
Service Bulletin/Repair Instructions
CORE – HEATER
109011
Service Bulletin/Repair Instructions
VALVE BODY & CONTROL UNIT – TRANSMISSION
S2508000078 REV.A
Service Bulletin/Repair Instructions
Ambient Temperature Readings Incorrect After a Heat Soak
S258A000025
Service Bulletin/Repair Instructions
Customer states Navigation is inaccurate, showing in wrong city or state.
08-394-25 REV. A
Service Bulletin/Repair Instructions
Telematics Box Module (TBM) Backup Battery Replacement When DTC B1E21 Is Present Technicians may experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle may exhibit/set the following Diagnostic Trouble Code (DTC): ● B1E21-96 - Backup Battery Component Internal Failure.
S2508000107
Service Bulletin/Repair Instructions
Comfort Seat Module (CSM) or Comfort Steering Wheel Module (CSWM) do Not Operate
9100568 Rev 1
Service Bulletin/Repair Instructions
Order regular part number for New, Unsold and Warranty units only. Verify Z part number availability. Order a Z part number for all Exchange Orders, Mopar, customer pay and service contract.
9100734
Service Bulletin/Repair Instructions
If the DTC B1E21-96: Backup Battery-Component Internal Failure is active and customer states Popup message will show at the radio: "Battery of Uconnect Box requires service. SOS call and related functions may be unavailable. Please visit an authorized dealer." PLEASE do not Replace the TBM module, only replace TBM Internal Battery (inside Telematics Box Module) and order PN68493347
9100735
Service Bulletin/Repair Instructions
Verify "Z" part number availability. Order a "Z" part number for all Exchange Orders: Warranty, Mopar, Customer pay and Service contract. Order"68" part number for New unsold units only
S2505000003
Service Bulletin/Repair Instructions
Diagnostic Trouble Code (DTC) C0050-00-Brake System Hydraulic Leak Set After Recent Repair.
S2523000090
Service Bulletin/Repair Instructions
MOPAR Bed Divider Kit Missing Lock Cylinder
S2523000091
Service Bulletin/Repair Instructions
Antilock Brake (ABS) Light On. Intermittent Or Implausible Wheel Speed Sensor Signal Diagnostic Trouble Codes (DTCs)
S258A000023
Service Bulletin/Repair Instructions
Intermittent Audio, No Audio, Distorted Audio
9100463REV1
Service Bulletin/Repair Instructions
2024-2025 DT with DTC P0070 OR P0073 If Mirror Ambient Temperature Sensor (AATS) isnot reading temp correctly or setting DTC P0073, P0070 - allow the sensor to updateproperly by driving the vehicle at highway speeds (above 20 MPH) for several miles (15minutes). This ensures sufficient airflow and temperature sampling for accurate readings. If the temperature still does not update, proceed with standard diagnostic procedures. 2025-2026 DT with DTC P0071 AND P0073 (vehicles built on or between 07/01/2025 -07/29/2025 - If BOTH DTCs are present, before replacing the sensor, refer to the latest TSBin Service Library for additional repair procedure(s). - If NO DTC is present, but temperatureshown in the cluster/radio is higher than expected, allow the sensor to update properly bydriving the vehicle at highway speeds (above 20 MPH) for several miles (15 minutes). Thisensures sufficient airflow and temperature sampling for accurate readings. If thetemperature still does not update, proceed with standard diagnostic procedures.
08-394-25
Service Bulletin/Repair Instructions
Telematics Box Module (TBM) Backup Battery Replacement When DTC B1E21 Is Present echnicians may experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle may exhibit/set the following Diagnostic Trouble Code (DTC): ● B1E21-96 - Backup Battery Component Internal Failure
108953
Service Bulletin/Repair Instructions
DUCT - CLEAN AIR
108886
Service Bulletin/Repair Instructions
SENSOR - ACCELERATION
S258A000021
Service Bulletin/Repair Instructions
Diagnostic Trouble Code (DTC) B15A1-00 Media Port Connection 1 Connection Found Set.
S2502000001
Service Bulletin/Repair Instructions
Lower Ball Joint / Lower Control Arm Servicing Updates.
S2308000034 REV.A
Service Bulletin/Repair Instructions
No Wireless Charging Or Slow Wireless Charging
108458
Service Bulletin/Repair Instructions
DETECTOR - EVAPORATIVE SYSTEM INTEGRITY MODULE
108461
Service Bulletin/Repair Instructions
DETECTOR - EVAPORATIVE SYSTEM INTEGRITY MODULE
9100724
Service Bulletin/Repair Instructions
If you receive a customer complaint regarding a missing Bed Divider Lock Cylinder on DT vehicles, do NOT install the part. This component is not part of the equipment for DT models since 2022 model year. Parts for Reference (Do NOT install): PN 68312242AE PN 68438041AA
108409
Service Bulletin/Repair Instructions
CORE - HEATER
108410
Service Bulletin/Repair Instructions
CORE - HEATER
S2508000100
Service Bulletin/Repair Instructions
Intermittent Uconnect Box Requires Service Message. TBM Setting Stored Or Pending DTCs B22A9, B1560, B1561, B1562
S1805000006 REV.B
Service Bulletin/Repair Instructions
ESC Light Illuminated. DTC C1252-92 VACUUM PUMP CONTROL CIRCUIT And Or P258B ELECTRONIC VACUUM PUMP PERFORMANCE
9100702
Service Bulletin/Repair Instructions
Dealer technicians have reported failures involving camshaft cap bolts breaking within the cylinder head assembly. This can lead to damage to camshaft towers, camshafts, and other cylinder head components. In many cases, the entire long block has been replaced unnecessarily. Do NOT replace the entire long block unless absolutely necessary. Perform a thorough inspection and replace only the cylinder head assembly if the damage is localized.
S2509000009
Service Bulletin/Repair Instructions
Engine Oil Leak
9100672 Rev 3
Service Bulletin/Repair Instructions
Replacement components for transfer case are no longer available. To repair issue, use the following part numbers and follow the I-sheet instructions for assembly: 68738079AA - HOUSING 68738084AA - CAM 68738085AA - GEAR 68737112AA - PLATE Please note that the part numbers listed here are transfer case components, not full transfer case part numbers.
S2524000012
Service Bulletin/Repair Instructions
High Voltage Air Conditioning Refrigerant Dye
S2522000003
Service Bulletin/Repair Instructions
Tire Pressure Monitor (TPM) Warning Lamp On Or Flashing. Sensor(s) Not Reading And Or Showing Dashes.
S2523000077 REV.A
Service Bulletin/Repair Instructions
Power Side-Step Module (PSSM) In Plant Mode, Power Running Boards do Not Deploy
S2508000076
Service Bulletin/Repair Instructions
Power Side Steps Deploy and Retract While the Vehicle is in Motion
9100670
Service Bulletin/Repair Instructions
Data collection required for all 2020-2026MY vehicles with 3.6L PSU engines during any of their first 3 engine oil changes. This data collection is applicable to all vehicle with engines with sales codes: ERG, ERC, EH3 and ERF. To assist with monitoring and quality improvement of the 3.6L engine, every time a vehicle comes for any of the first 3 oil changes, please use wiTECH to record the total engine idle time and the total engine runtime. 1. Prior to perform the oil change connect wiTECH diagnostic tool. 2. Navigate to the topology screen on the action item section. 3. Once the topology screen loads, disconnect wiTECH and continue with oil change.
9100672
Service Bulletin/Repair Instructions
Tech tip used to notify that if any of the part numbers for replacement for the TRX/RHO t-case is no longer available, dealers will need to request the new DDG parts for service replacements. They need to order the following new part numbers: 68738079AA, 68738084AA, 68738085AA, 68737112AA and follow the iSheet instructions for assembly.
9100672 Rev 1
Service Bulletin/Repair Instructions
Replacement T-Case is no longer available. To repair issue, use the following parts numbers and follow the I-sheet instructions for assembly: 68738079AA - HOUSING 68738084AA - CAM 68738085AA - GEAR 68737112AA - PLATE
S2323000020 REV.B
Service Bulletin/Repair Instructions
Power Side Steps Reverse, Stop In Motion, And/Or Do Not Deploy Or Stow
S2519000009
Service Bulletin/Repair Instructions
Diagnostic Trouble Code (DTC) C221F-00, C2223-00, C221C-00, C0051-54 Present After Electric Power Steering (EPS) Replacement.
03-008-25
Service Bulletin/Repair Instructions
Rear Axle Vibration Shudder Or Chatter Customers may experience the following: ● A chatter, shudder, or vibration from the rear axle during turns. NOTE: This may happen more as the vehicle ages, especially if the vehicle is used extensively for towing or hauling heavy loads. The cause of the concern may be due to degradation of the rear axle fluid. It is very important to follow the routine maintenance schedules on these vehicles when it comes to changing the rear axle fluid if the vehicle is used primarily for towing or hauling heavy loads. If you experience a vehicle with the above condition, please perform the proper maintenance procedures for the rear axle and replace the fluid first before replacing any hardware components. NOTE: This service bulletin is only applicable to vehicles that have no history of an axle fluid replacement. If the vehicle usage includes police, taxi, fleet, off-road or frequent trailer towing, regular axle fluid changes are required every 3 years or 30,000 miles (whichever comes first) per the Maintenance Schedule in the vehicle Owner's Manual. This bulletin involves changing the rear axle lube to possibly address a chatter, shudder or vibration.
23-008-25 REV. A
Service Bulletin/Repair Instructions
Exterior Front Lamps Condensation Clearing Procedure *Some customers may report that on occasion vehicle exterior front lamps (headlamps, fog lamps, grille lamps, logo lamps or signature lamps) assemblies are fogged with a light layer of condensation on the inside of the lenses*
02-002-25 REV. A
Service Bulletin/Repair Instructions
Shock And Strut Diagnosis And Replacement Guidelines Leaking, noisy, or weak shocks or struts.
08-301-25
Service Bulletin/Repair Instructions
Flash: Security Gateway Module (SGW) Update Customers may experience the following: ● Intermittent 'A/C change mode' message popup on radio screen. Rear View Camera (RVC) not affected. This bulletin involves updating the SGW with the latest available software.
S2508000078
Service Bulletin/Repair Instructions
Ambient Temperature Readings Incorrect After a Heat Soak
106352
Service Bulletin/Repair Instructions
SHOCK ABSORBER – SUSPENSION & SHOCKS - REAR
S2522000002
Service Bulletin/Repair Instructions
Customer Indicates Tire Pressure Monitoring System (TPMS) Lights On Dash.
S2523000076
Service Bulletin/Repair Instructions
Active Air Dam Diagnostic Trouble Codes (DTC) U0645, C0604.
S2523000077
Service Bulletin/Repair Instructions
Power Side Step Module (PSSM) In Plant Mode.
31-001-25 REV. B
Service Bulletin/Repair Instructions
Aluminum Body Panel Corrosion Repair Aluminum corrosion or bubbling along the leading edge of hood, hinges or other exterior surface areas of the hinges, doors, fenders, swing gates or liftgates.
31-001-25 REV. A
Service Bulletin/Repair Instructions
Aluminum Body Panel Corrosion Repair Aluminum corrosion or bubbling along the leading edge of hood, hinges or other exterior surface areas of the hinges, doors, fenders, swing gates or liftgates.
31-001-25
Service Bulletin/Repair Instructions
Aluminum Body Panel Corrosion Repair Aluminum corrosion or bubbling along the leading edge of hood, hinges or other exterior surface areas of the hinges, doors, fenders, swing gates or liftgates
S258A000019
Service Bulletin/Repair Instructions
Radio Does Not Turn On Automatically When Vehicle Is Started
S258A000017
Service Bulletin/Repair Instructions
Door speaker Inoperative or No Sound
106241
Service Bulletin/Repair Instructions
LAMP - DOME
S2509000001 REV.B
Service Bulletin/Repair Instructions
Engine Rattle Noise
23-006-25 REV. B
Service Bulletin/Repair Instructions
Windshield Wiper Blade Maintenance Customers may experience one or more of the following: ● Wiper blades that chatter/streak/jump/skip/smear or make noise while traveling across the windshield.
S2523000072
Service Bulletin/Repair Instructions
Central ADAS Decision Module (CADM), Long Range Camera Front (LRCF), Advanced Driver Assist System (ADAS). AEB ACC FCW Message On Cluster.
S2422000001 REV.D
Service Bulletin/Repair Instructions
Tire Pressure Monitor (TPM) Service Information. TPM Lamp On.
08-221-25
Service Bulletin/Repair Instructions
115V Power Outlet LED Always On The amber LED remains continuously illuminated, regardless of whether the switch button is activated. This bulletin involves replacing the inverter switch.
S2523000070
Service Bulletin/Repair Instructions
Central ADAS Decision Module (CADM) Diagnostic Trouble Codes C00C0-4A, C00C1-4A, C00C5-4A.
S258A000018
Service Bulletin/Repair Instructions
Intermittent HVAC Pop Up Window On The Radio Screen
105648
Service Bulletin/Repair Instructions
MODULE - ENGINE CONTROLLER
S2519000006
Service Bulletin/Repair Instructions
Steering Repair Information Involving Toe Angle. Tie Rod And Or Electric Power Steering (EPS) Units.
S2524000008
Service Bulletin/Repair Instructions
Customer Indicates The Air Conditioning Blows Warm
21-009-25 REV. C
Service Bulletin/Repair Instructions
850RE D Clutch Repair Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must have at least 11,265 km (7,000 mi.) and exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P0733-00 - Gear 3 Shift Incorrect Ratio. ● P1DA8-00 - Incorrect Gear Ratio Clutch A B or D Defective. ● P1D92-00 - Incorrect Gear Ratio - Clutch 4 Defective. Customers may also comment on one or more of the following: ● Transmission slips when shifting. ● Vehicle will not move in reverse. ● Vehicle will not shift higher than third gear This bulletin involves replacing the D clutch.
S2208000138 REV.B
Service Bulletin/Repair Instructions
Decreased Remote Start And RKE Range. Tire Pressure Sensors Values Are Not Displayed
S2408000104 REV.A
Service Bulletin/Repair Instructions
Remote Keyless Entry (RKE) has Reduced Range, Remote Start Inoperative, Multiple Keyless-Go Push Attempts to Start, Key not Detected message, Tire Pressure Warning Lamp On
9100622
Service Bulletin/Repair Instructions
When replacing a camshaft and parts kit (P/N 68661146xx and/or 68661147xx), it is NOT necessary to order the roller-finger followers (rocker arms) separately, as these are included in the camshaft parts kit.
S2523000062
Service Bulletin/Repair Instructions
Bumper Mounted 7 Pin Trailer Tow Connector
105288
Service Bulletin/Repair Instructions
VALVE - CHECK
9100614
Service Bulletin/Repair Instructions
ADJUSTER Valve Lash Customer's complaint may include a ticking noise coming from the engine. Technician's observations can refer to spongy or stuck hydraulic lash adjusters. Exhaust lash adjusters found with a "spongy" condition (compressible plunger) leading to the assumption of being defective/malfunctioning. EXHAUST lash adjusters are designed to be COMPRESSIBLE by hand. Intake lash adjusters found with a stiff or stuck condition (non-compressible plunger) leading to the assumption of being defective/malfunctioning. INTAKE lash adjusters are designed to be NON COMPRESSIBLE by hand. Do Not Replace EXHAUST lash adjusters when the following condition is present: should be compressible, but they will exert a reactionary spring force during compression and return to full expansion without a compression force. Do Not Replace INTAKE lash adjusters when the following condition is present: should feel very firm and difficult to compress. Once the correct functioning of the intake and exhaust lash adjusters is validated with the procedure above, refer to the Service Manual "HYDRAULIC LIFTER(S) NOISE DIAGNOSIS" procedure. After the corresponding service procedures from the Service Manual involving the Lash Adjusters have been conducted, refer to the detailed instructions in the Service Manual to diagnose and/or service any other component.
104974
Service Bulletin/Repair Instructions
LAMP - DOME
105590
Service Bulletin/Repair Instructions
Warranty Newsletter – Volume 11, Issue 6
105591
Warranty Program/Extension
FCA Caribbean Warranty Newsletter – Volume 11, Issue 6
OTHERDOC_132
Over The Air
Global Telematics Box Module Over The Air Update from 5.39.1 to 5.65 TBM2.0 Software Version (FOTA) Customers may experience one or more of the following: - Error display of "Uconnect Box Requires Service/Wifi Unavailable" popups; [ TBM DTC B22A9-96 Internal Performance Failure ]. - Error display of "Uconnect Box Requires Service" pop-ups; [ TBM DTCs B1560, B1561, B1562 - Antenna loose connection ].
104970
Service Bulletin/Repair Instructions
CORE - HEATER
9100592
Service Bulletin/Repair Instructions
LAMP Courtesy/Ambient Courtesy / Ambient Lamp: Light guide not fully seated into the retainer during IP sub-assembly due to inconsistent operator installation effort, leading to latent BSR issue that manifests under customer usage conditions. Solution: remove and reinstall light guide to be fully seated in the bracket retainer.
9100599
Service Bulletin/Repair Instructions
Underhood start/stop safety The customer may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following Diagnostic Trouble Code (DTC): - P152E Engine -Hood Switch 2 Circuit High. - DTC P152F Customers may also experience: - Start/Stop system warning light. - Start/Stop inoperable. - Remote start inoperable. Diagnosis: - Using a Scan Tool (wiTECH) with the appropriate Diagnostic Procedures available in DealerCONNECT/Service Library, verify all related systems are functioning as designed. If DTCs or symptom conditions, other than the one listed are present, record the issues on the repair order and repair as necessary before proceeding further with this bulletin. - If any vehicle exhibits any of the symptoms listed above in the customer symptom section, perform the Repair Procedure. - Special Tools/Equipment: wiTECH or equivalent. Repair Procedure: 1. Open the hood and locate the hood switch 2. Push in on the two locking tabs and pull them out. 3. Disconnect the wire connector from the switch. 4. Connect the wires to the same hood switch. 5. Push the switch back into the hold until both lock tab are engaged. 6. Clear all DTCs that may have been set in any module during this repair procedure. 7. In case the P152F/P152E DTCs persist, repeat the procedure with a new/spare/known good switch and repeat steps 5 and 6. 8. Replace switch installed during previous step for the original switch of the vehicle. If DTCs P152F/P152E are not present, leave the original switch installed and do not document the change of the switch in the repair process/narrative.
S2509000003REVA
Service Bulletin/Repair Instructions
Engine Overheating Customer Complaint/Technician Observation: Customer complaint may include engine “overheating”. Discussion: When dealing with a customer complaint of engine ”overheating”, it is most important to understand exactly what the customer’s definition is of “overheating”. An explanation from the customer of what exactly happened is necessary. Overheating descriptions could include warning lamp(s), messages in the cluster, steam/smoke coming from under the hood, gauge “running higher than normal”, actual engine temperature higher than what the customer considers normal, smells hot, coolant leaking under the vehicle, etc. Observed engine operating temperatures of 245 F (118 C) degrees or lower are typical and are NOT considered overheating.
9100576
Service Bulletin/Repair Instructions
Transfer Case Motor Gear: Confirm the attachment points from the wiring routes when they inspect a shift motor on the t-case. Review the connection of the connector X238A, make sure it's fully seated and that the lever is fully locked on the connector.
08-157-25 REV. A
Service Bulletin/Repair Instructions
R1H Radio Over The Air Update from T27.46 to U29.44 then U35.26 Software Version (FOTA)
02-002-25
Service Bulletin/Repair Instructions
Shock And Strut Diagnosis And Replacement Guidelines Leaking, noisy, or weak shocks or struts.
9100574
Service Bulletin/Repair Instructions
Radio: Capture software version from radio. Record or document software version prior to troubleshooting, as soon as any infotainment issue has been found or reported. Also always document in claim. Steps to capture Radio version number: 1. Go to "Vehicle" 2. Go to "Settings" 3. Go to "System Information" 4. Find the radio version from "Version information" Example software version: U37.2, U39.4, etc.
09-011-25
Service Bulletin/Repair Instructions
Misfire Diagnostic Trouble Codes (DTCs), Rough Idle, Valvetrain Noise Customers may experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle may exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P0301 - Cylinder 1 Misfire. ● P0302 - Cylinder 2 Misfire. ● P0303 - Cylinder 3 Misfire. ● P0304 - Cylinder 4 Misfire. ● P0305 - Cylinder 5 Misfire. ● P0306 - Cylinder 6 Misfire. Customers may comment on one or more of the following: ● Rough idle. ● Valvetrain noise.
S2508000038
Service Bulletin/Repair Instructions
Key Fob is Damaged, Case is Separating
S2508000039
Service Bulletin/Repair Instructions
Universal Garage Door Opener (UGDO) Inoperative, LED Indicator Lamps Not Illuminating
S2308000120 REV.D
Service Bulletin/Repair Instructions
Rain Sensing Auto Wipers and Auto on Head Lamps Inoperative
S2323000002 REV.A
Service Bulletin/Repair Instructions
Washer Light On And Will Not Turn Off After Adding Washer Solvent.
104686
Service Bulletin/Repair Instructions
BOLT - HEX FLANGE HEAD
9100498 Rev 3
Service Bulletin/Repair Instructions
3.6L PSU Long Block Misfire DTC codes and/or rough idle and/or valvetrain noise. Refer to SOL # S2509000004. It is also important to confirm that the vehicle being repaired has the latest calibration/software update for oil pump operation mode (high pressure mode) during engine start up. RU, VF, WL & WD vehicles already include the latest oil pump mode in all 25MY and beyond. 24MY service releases are also available. JL & JT were updated as a running change in 24MY and beyond (08/15/24 & 08/19/24 respectively). 24MY service releases available. DT was updated starting 25MY and beyond. If the vehicle to be repaired is a 24MY vehicle with a service release available, please follow the released service procedures to update to the corresponding calibration/software.
9100534 Rev 1
Service Bulletin/Repair Instructions
Transmission "Transmission For transmission concerns related to DTCs P0733-00, P1DA8-00, and/or P1D92-00, a repair is available, and transmission replacement is NOT required. Please reference TSB 21-009-25 Rev. A, for details on D-clutch replacement. Please also note, visible ""glitter"" or debris in the pan and fluid color/condition/odor is NOT an indicator of transmission health and should not be used as the reason for unit replacement. Complete unit replacements instead of repairs for these DTCs may be subject to chargeback."
9100570
Service Bulletin/Repair Instructions
Transmission Fluid Please note fluid color/condition/odor is NOT an indicator of transmission health and should not be used as the reason for unit replacement. Visible "glitter" or debris in the pan does not justify complete unit replacements.
08-157-25
Service Bulletin/Repair Instructions
R1H Radio Over The Air Update from T27.46 to U29.44 then U35.36 Software Version (FOTA) 2023 - 2024 (DT) RAM 1500 Pickup This bulletin applies to vehicles equipped with a Global Telematics Box Module (Sales Code RDG) and without IP Badge "TRX" (Sales Code XHD) and one of the following radios: ● Uconnect 5 Nav w 8.4" Display (USA) (Sales Codes UBL). ● Uconnect 5 Nav w 8.4" Display (CAN) (Sales Codes UEL). ● Uconnect 5 Nav w 12.0" Display (USA) (Sales Code UBQ) ● Uconnect 5 Nav W 12.0" Display (CAN) (Sales Code UEQ) ● Uconnect 5 NAV W 14.4" Display (USA) (Sales Code UBW) ● Uconnect 5 NAV W 14.4" Display (CAN) (Sales Code UEW) This bulletin provides information regarding the latest FOTA update and provides the service technician an overview of the steps a customer will need to take to complete the update. The radio software will be updated from T27.46 to U29.44 then U35.36.
S258A000015
Service Bulletin/Repair Instructions
Wrong Graphic In Ram TRX Performance Pages
S2509000003
Service Bulletin/Repair Instructions
Engine Overheating
104684
Service Bulletin/Repair Instructions
HEADLINER - NONE
S2518000004
Service Bulletin/Repair Instructions
Mil-On/Check Engine Lamp-On
103774
Service Bulletin/Repair Instructions
LAMP - DOME
S2523000035
Service Bulletin/Repair Instructions
Door Trim Panel Fitment. Warpage, Buzz Squeak Rattle (BSR) Noises. Poor Audio Sound Quality From Door Speaker.
S2523000038
Service Bulletin/Repair Instructions
Drivers Side Exterior Mirror Takes Longer To Defrost Or Clear Than The Passenger Side Exterior Mirror.
9100568
Service Bulletin/Repair Instructions
DISPLAY Order regular part number for New unsold and Warranty units only. Verify Z part number availability. Order a Z part number for all Exchange Orders: Mopar, customer pay and service contract.
S2308000120 REV.C
Service Bulletin/Repair Instructions
Rain Sensing Auto Wipers and Auto on Head Lamps Inoperative
21-009-25 REV. B
Service Bulletin/Repair Instructions
850RE D Clutch Repair **Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must have at least 11,265 km (7,000 mi.) and exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs):** ● P0733-00 - Gear 3 Shift Incorrect Ratio. ● P1DA8-00 - Incorrect Gear Ratio Clutch A B or D Defective. ● P1D92-00 - Incorrect Gear Ratio - Clutch 4 Defective. Customers may also comment on one or more of the following: ● Transmission slips when shifting. ● Vehicle will not move in reverse. ● Vehicle will not shift higher than third gear This bulletin involves replacing the D clutch.
S2523000024
Service Bulletin/Repair Instructions
Rear Defogger Solder Terminals Detached.
S2408000015 REV.D
Service Bulletin/Repair Instructions
Remote Keyless Entry (RKE) Functions Do Not Work, Intermittent Vehicle Response When Using the RKE, Key Not Programmed, Adding Remote Start
104179
Service Bulletin/Repair Instructions
MODULE - IGNITION
S2509000004
Service Bulletin/Repair Instructions
Misfire DTCs, Rough Idle, Valvetrain Noise
S2508000014 REV.B
Service Bulletin/Repair Instructions
Security Gateway (SGW) Module is Setting Diagnostic Trouble Code (DTC) U3033-00 Control Module Security Certificate Missing or Invalid
S2509000001 REV.A
Service Bulletin/Repair Instructions
Engine Rattle Noise
9100534
Service Bulletin/Repair Instructions
Transmission For transmission concerns related to DTCs P0733-00, P1DA8-00, and/or P1D92-00, a repair is available, and transmission replacement is NOT required. Please reference TSB 21-009-25 Rev. A, for details on D-clutch replacement. Please also note, fluid color/condition/odor is NOT an indicator of transmission health and should not be used as the reason for unit replacement. Complete unit replacements instead of repairs for these DTCs may be subject to chargeback.
S2508000020
Service Bulletin/Repair Instructions
Odometer Blinking, Security Gateway (SGW) Diagnostic Trouble Codes (DTCs) Diagnostics
9100471
Service Bulletin/Repair Instructions
CANISTER Vapor -If an issue is detected with the Evaporative System Integrity Module (ESIM) Detector and not the Vapor Canister, only replace the ESIM Detector. -Before replacing the Vapor Canister due to Hard to Fill condition, replicate the condition at the Gas Station. If the condition is replicated, then check: 1) for kinked or pinched Clean Air Hose between the ESIM and the EVAP Air Filter; 2) for plugged EVAP Air Filter; 3) for kinked or pinched Vapor Hose between the Fuel Tank and the Vapor Canister. If the EVAP Filter is restricted, the replace the Filter. -Check if the Vapor Canister is flooded with fuel or the Recirculation Line has fuel. If fuel is found in the Vapor Canister or the Recirculation Line, then drop the Fuel Tank, remove the FDM Lock Ring to check if the internal Vapor Line is properly connected to the FDM Port. If the Vapor Line is not connected, then drain the fuel from the internal Vapor Line and properly connect to the FDM. Replace the Vapor Canister and the ESIM.
S258A000005 REV.A
Service Bulletin/Repair Instructions
Trailer Tow App Gauges Not Showing Data in Widget Screen
S2508000014 REV.A
Service Bulletin/Repair Instructions
Security Gateway (SGW) Module is Setting Diagnostic Trouble Code (DTC) U3033-00 Control Module Security Certificate Missing or Invalid
103849
Service Bulletin/Repair Instructions
D-25-05 DIPAP Requirements - Addition of Headlamps and Tail Lamps - 2022 - 2025 RAM 1500 Pickup (DT) - All Dealers
103858
Service Bulletin/Repair Instructions
ID-25-04 DIPAP Requirements - Addition of Headlamps and Tail Lamps - 2022 - 2025 RAM 1500 Pickup (DT) - All Dealers
S2509000002
Service Bulletin/Repair Instructions
Engine Noise
S258A000009
Service Bulletin/Repair Instructions
Apple CarPlay Does Not Complete The First Initial Wireless Connection.
S2505000001
Service Bulletin/Repair Instructions
CEL (Check Engine Lamp) C006A-49 Multi-Axis Acceleration Sensor Internal Electronic Failure And C10CC-00 ESC Sensors.
02-001-25
Service Bulletin/Repair Instructions
Front Lower Control Arm Stabilizer Link Noise Customers may experience the following: ● Rattle or clunk noise coming from the front end of the vehicle when driving over bumps, performing turns or during normal operation. This bulletin involves road testing and possibly tightening the stabilizer link attachment to lower control arm nut.
9100498 REV 1
Service Bulletin/Repair Instructions
3.6L PSU Long Block Misfire DTC codes and/or rough idle and/or valvetrain noise. These conditions may be related to worn intake camshaft high lift lobe(s), and intake rocker arm(s) high lift slider. High mileage failure (10,000-60,000 miles). 1. Remove the valve cover(s) per the released service procedures. The use of a stethoscope or DTC specific cylinder misfire codes can help to locate the condition to the left or right bank. 2. Once it has been visually confirmed that there is wear on the high lift intake lobe(s) & rocker arm(s) slider, there is a special service kit for this type of repair which should be used, instead of replacing the complete engine/long block. This kit contains the parts required for the repair (intake cam, rocker arms, sealer and gaskets). Once it is confirmed that the repair will be done using the camshaft/Rocker arms kit, it is also important to confirm that the vehicle being repaired has the latest calibration/software update for oil pump operation mode (high pressure mode) during engine start up. RU, VF, WL & WD vehicles already include the latest oil pump mode in all 25MY and beyond. 24MY service releases are also available. JL & JT were updated as a running change in 24MY and beyond (08/15/24 & 08/19/24 respectively). 24MY service releases available. DT was updated starting 25MY and beyond. If the vehicle to be repaired is a 24MY vehicle with a service release available, please follow the released service procedures to update to the corresponding calibration/software update.
S2108000015 REV.J
Service Bulletin/Repair Instructions
Uconnect Box Require Service Message
102935
Service Bulletin/Repair Instructions
VALVE BODY & CONTROL UNIT - TRANSMISSION
9100500
Service Bulletin/Repair Instructions
Touchscreen For all infotainment system repairs (touchscreens, radios, etc.), refurbished parts may be available. Follow the Infotainment Ordering guide available under the "Parts" section of Dealer Connect: DealerCONNECT> Parts> News& Information> Audio & Electronic Products Exchange Process
103237
Service Bulletin/Repair Instructions
RADIATOR - ENGINE COOLING
103238
Service Bulletin/Repair Instructions
RADIATOR - AUXILIARY
S2509000001
Service Bulletin/Repair Instructions
Engine Rattle Noise
103288
Service Bulletin/Repair Instructions
CAMERA - REAR VIEW
103289
Service Bulletin/Repair Instructions
CAMERA - REAR VIEW
103291
Service Bulletin/Repair Instructions
PANEL - B PILLAR LOWER TRIM
09-003-25
Service Bulletin/Repair Instructions
Oil Leaking From Oil Filter Area Customers may experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle may exhibit/set the following Diagnostic Trouble Code (DTC): ● P06DD - Engine Oil Pressure Control Circuit Stuck Off. Customers may comment on the following: ● Oil found on the ground beneath the vehicle.
S258A000006
Service Bulletin/Repair Instructions
Rear ParkView Backup Camera Guidelines Not Appearing On Radio
23-008-25
Service Bulletin/Repair Instructions
Headlamp Condensation Clearing Procedure Some customers may report that on occasion, vehicle exterior head lamp assemblies are fogged with a light layer of condensation on the inside of the lenses.
S2323000004 REV.A
Service Bulletin/Repair Instructions
Defogger Is Not Working. Terminal Detached From The Glass.
S228A000005 REV.E
Service Bulletin/Repair Instructions
Uconnect Box Error Message, With Active or Stored Cellular Antenna Open or Short Diagnostic Trouble Codes (DTCs)
9100498
Service Bulletin/Repair Instructions
3.6L PSU Long Block Misfire DTC codes and/or rough idle and/or valvetrain noise. These conditions may be related to worn intake camshaft high lift lobe(s), and intake rocker arm(s) high lift slider. High mileage failure (10,000-60,000 miles). 1. Remove the valve cover(s) per the released service procedures. The use of a stethoscope or DTC specific cylinder misfire codes can help to locate the condition to the left or right bank. 2. Once it has been visually confirmed that there is wear on the high lift intake lobe(s) & rocker arm(s) slider, there is a special service kit for this type of repair which should be used, instead of replacing the complete engine/long block. This kit contains the parts required for the repair (intake cam, rocker arms, sealer and gaskets).
S2508000014
Service Bulletin/Repair Instructions
Security Gateway (SGW) Module is Setting Diagnostic Trouble Code (DTC) U3033-00 Control Module Security Certificate Missing or Invalid
9100493
Service Bulletin/Repair Instructions
SWITCH AND BEZEL Front Door Before replacing the Window Switch/Mirror Switch, please follow these steps: 1.- Check for what DTC are detected and take proper steps acceding to the DTC's. 2.- Make sure all the switches are properly connected to their harness, disconnect the switch and reconnect it. 3.- Review the window Switch for any physical issue (Button stuck, broken) If after performing these steps the switch remains faulty. Follow suggested repairs per diagnostics performed.
S258A000005
Service Bulletin/Repair Instructions
Trailer Tow App Gauges Not Showing Data in Widget Screen
21-009-25 REV.A
Service Bulletin/Repair Instructions
D Clutch Repair Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P0733-00 - Gear 3 Shift Incorrect Ratio. ● P1DA8-00 - Incorrect Gear Ratio Clutch A B or D Defective. ● P1D92-00 - Incorrect Gear Ratio - Clutch 4 Defective. Customers may also comment on one or more of the following: ● Transmission slips when shifting. ● Vehicle will not move in reverse. ● Vehicle will not shift higher than third gear. This bulletin involves replacing the D clutch
S2523000007
Service Bulletin/Repair Instructions
Trailer Brake Information Displays In Cluster With No Trailer Connected.
9003980
Service Bulletin/Repair Instructions
SWITCH Headlamp Before replacing the Headlamp Switch for faulty dimmer operation. Please follow the next steps to corroborate if the Headlamp Switch is malfunctioning: 1.- Please disconnect and reconnect the headlamp Switch. And verify if the issue is corrected. 2.- Review the internal resistance of the switch: a.- For the Right Dimmer (IP) between Pins 6 & 3. The value should be around 5.74 KOhms, when in the lowest position to 311 ohms in the top position (Parade Detent). b.- For the left Dimmer (Ambient Light) between pins 8 & 3. The value should be around 14.52 KOhms, when in the lowest position to 182 ohms in the top position. If a problem is found in the resistor values. Please replace the Switch.
S1408000384 REV.H
Service Bulletin/Repair Instructions
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS Related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
102948
Service Bulletin/Repair Instructions
MODULE - ANTI-LOCK BRAKE SYSTEM
102950
Service Bulletin/Repair Instructions
MODULE - ANTI-LOCK BRAKE SYSTEM
S2523000005
Service Bulletin/Repair Instructions
Squeak Noise From Brake Pedal When Pressed And Or Released.
9100460 REV1
Service Bulletin/Repair Instructions
ARM Lower Control WHAT: Clunking noise from Front Stabar link to Front Lower Control Arm (FLCA). WHY: The joint is coming loose due to loss of clamp load when there is embedment on FLCA mating surface to the stabar link ball stud. We are currently updating the stabar link design and new design will be implemented in March 2025. HOW: If this Front stabar link to FLCA joint torque is under the residual torque of 70Nm, please retorque the joint to this spec of 110 (Min 70-Max 138). Otherwise proceed with regular diagnosis.
21-009-25
Service Bulletin/Repair Instructions
D Clutch Repair Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P0733-00 - Gear 3 Shift Incorrect Ratio. ● P1DA8-00 - Incorrect Gear Ratio Clutch A B or D Defective. ● P1D92-00 - Incorrect Gear Ratio - Clutch 4 Defective. **Customers may also comment on one or more of the following: ● Transmission slips when shifting. ● Vehicle will not move in reverse. ● Vehicle will not shift higher than third gear.** This bulletin involves replacing the D clutch."
9100487
Service Bulletin/Repair Instructions
MODULE Steering Control Before replacing the steering column control module (SCCM) due to turn signal inop, wipers inop, steering controls inop, TCS light DTC C0051 or horn blowing while turning, please follow these steps: 1.- Refer to service library procedure and follow diagnosis steps. 2.- If failure still present, make sure all the switches', horn's, airbag's harness are properly connected and there is no corrosion or pinching, disconnect the switches & reconnect them, and reverify the issue. 3.- Verify if failure is still present, review if there is lack of communication between SCCM and BCM. For example, activate turn signals or wipers. 4.- Read at the BCM diagnosis session if BCM is receiving information from SCCM. Through diagnosis review if activation from horn, wipers or turn signal is requested and are working. 5.- Disconnect the SCCM fuse for around 30s,and repeat the previous steps to see if failure still present. 6.- Do a hard reset to BCM and evaluate if any DTC is set. Retest if failure still present. 7.- Before replacing the SCCM disconnect it and reconnect it again. If there are no DTC's active, physical defects, steering controls inop, wipers inop, nor turn signal inop, horn inop, then SCCM does not need to be replaced.
S2523000003
Service Bulletin/Repair Instructions
Door Latch, Handle And Ajar Additional Service Information.
S2523000002
Service Bulletin/Repair Instructions
Outside Exterior Mirror Power Extend And/Or Retract Is Not Fully Functional.
S1408000384 REV.G
Service Bulletin/Repair Instructions
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
9100468
Service Bulletin/Repair Instructions
FUEL VAPOR CANISTER FILTER EVAP Fuel Filters are to be checked for restriction / blockage on a regular schedule as indicated in the Owner s Manual. If the Filter is restricted or blocked then replace the part. For customers that drive light duty trucks in extreme dusty and dirty road conditions, please reference information only TSB 25-009-24 for an available MOPAR Dual EVAP Filter kit that is customer paid.
21-039-24 REV. H
Service Bulletin/Repair Instructions
D Clutch Repair Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P0733-00 - Gear 3 Shift Incorrect Ratio. ● P1DA8-00 - Incorrect Gear Ratio Clutch A B or D Defective. ● P1D92-00 - Incorrect Gear Ratio - Clutch 4 Defective. This bulletin involves replacing the D clutch
S2208000045 REV.B
Service Bulletin/Repair Instructions
Backup Camera Poor Image Quality Inspection
9100460
Service Bulletin/Repair Instructions
ARM Lower Control WHAT: Clunking noise from Front Stabar link to Front Lower Control Arm (FLCA). WHY: The joint is coming loose due to loss of clamp load when there is severe embedment on FLCA mating surface to the stabar link ball stud. We are currently updating the stabar link design and new design will be implemented in March 2025. HOW: If this Front stabar link to FLCA joint torque is under the residual torque of 70Nm, please retorque the joint to this spec of 110 (Min 70-Max 138). Otherwise proceed with regular diagnosis.
S248A000018
Service Bulletin/Repair Instructions
Trailer Tow Pages App Gauges Not Showing Data After Radio Update
25-009-24
Service Bulletin/Repair Instructions
Dual EVAP System Extreme Duty Vapor Canister Filter Kit Customers operating fleet or severe/extreme duty gasoline vehicles in continuous dusty driving conditions can plug the single OE filter system and may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle may exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P0441 - EVAP Purge System Performance. ● P062A - Fuel Pump Control Performance. Customers may also experience one or more of the following: ● Hard to fill fuel tank with fuel. ● Premature shut-off of the gas nozzle when refueling. ● Flow back of fuel while refueling.
18-085-24
Service Bulletin/Repair Instructions
Flash: Powertrain Control Module (PCM) Updates Customers may experience the following: ● Cruise control set speed and actual vehicle speed are offset. This bulletin involves reprogramming the PCM with the latest available software.
101935
Service Bulletin/Repair Instructions
GLASS - BACKLITE
101936
Service Bulletin/Repair Instructions
GLASS - BACKLITE
101789
Service Bulletin/Repair Instructions
BUSHING - STABILIZER BAR
08-235-24
Service Bulletin/Repair Instructions
Flash: Instrument Panel Cluster (IPC) Updates Customers may comment on the following: ● Arabic text on the IPC is written in reverse order (left to right as opposed to right to left). This creates incomprehensible text on the screen. This bulletin involves updating the IPC with the latest available software.
08-225-24
Service Bulletin/Repair Instructions
Flash: Instrument Panel Cluster (IPC) Updates Customers may comment on the following: ● Arabic text on the IPC is written in reverse order (left to right as opposed to right to left). This creates incomprehensible text on the screen. This bulletin involves updating the IPC with the latest available software.
S2422000001 REV.C
Service Bulletin/Repair Instructions
Tire Pressure Monitor (TPM) Service Information. TPM Lamp On.
101232
Service Bulletin/Repair Instructions
Plate - Planetary
S2403000006
Service Bulletin/Repair Instructions
Service 4WD System Message Displayed. Diagnostic Trouble Code (DTC) C1472-13 Transfer Case Clutch Control Circuit Open, Set.
101010
Service Bulletin/Repair Instructions
SWITCH – MULTIFUNCTION
100635
Service Bulletin/Repair Instructions
VALVE BODY & CONTROL UNIT - TRANSMISSION
PDI Release: 2024_10_V1
Other
Open and close rear glass window 2 times and check seal is not hanging or loose
S2423000043
Service Bulletin/Repair Instructions
Dome Lamp LED And Incandescent Bulb Servicing.
100774
Service Bulletin/Repair Instructions
SWITCH - HEADLAMP
97802
Service Bulletin/Repair Instructions
SWITCH - HEADLAMP
09-020-24
Service Bulletin/Repair Instructions
Loss of Power in Reverse Customers may comment on one or more of the following: ● During engine cold start, the vehicle exhibits low torque when shifted into reverse gear. ● Loss of power in reverse gear. This bulletin provides information regarding the loss of engine torque when performing a cold start and immediately shifting into gear
S2423000024 REV.B
Service Bulletin/Repair Instructions
Door Ajar Light On With Door(s) Closed.
S2408000104
Service Bulletin/Repair Instructions
Remote Keyless Entry (RKE) has Reduced Range, Remote Start Inoperative, Multiple Keyless-Go Push Attempts to Start, Key not Detected message, Tire Pressure Warning Lamp On
100595
Warranty Program/Extension
WARRANTY BULLETIN D-24-15 announces the addition of the Rear Axle Assembly replacement for 2019 - 2024 RAM 3500 Cab Chassis (DD), RAM 4500/ 5500 Cab Chassis (DP), RAM 3500 Pickup (D2), RAM 2500 Pickup (DJ), RAM 1500 Pickup (DS) and RAM 1500 Pickup (DT) vehicles to the Powertrain Pre-Authorization program for all dealers (Base, Plus & Premium) to ensure proper repair of Rear Axle Assembly failures and to assist in quality improvements. REV.A
100599
Warranty Program/Extension
FCA Caribbean Warranty Bulletin ID-24-16 Rev. Announces the addition of the Rear Axle Assembly replacement for 2019 - 2024 RAM 3500 Cab Chassis (DD), RAM 4500/ 5500 Cab Chassis (DP), RAM 3500 Pickup (D2), RAM 2500 Pickup (DJ), RAM 1500 Pickup (DS) and RAM 1500 Pickup (DT) vehicles to the Powertrain Pre-Authorization program to ensure proper repair of Rear Axle Assembly failures and to assist in quality improvements. REV.A
S228A000017 REV.A
Service Bulletin/Repair Instructions
Battery Drain Suspected or "Identified" From USB or Media Hub
100418
Service Bulletin/Repair Instructions
MODULE - ANTI-LOCK BRAKE SYSTEM
100421
Service Bulletin/Repair Instructions
MODULE - ANTI-LOCK BRAKE SYSTEM
9100409
Service Bulletin/Repair Instructions
TRANSFER CASE Before replacing a transfer case unit for fault codes C1444-98 and/or C1477-4B, be sure to reference TSB 21-048-24 for potential transfer case shift motor replacement
S2423000027 REV.A
Service Bulletin/Repair Instructions
Horn Sound Is Weak, Off Tone, Or Inoperative.
S2308000155
Service Bulletin/Repair Instructions
Water Intrusion Of The RFH Causes Erratic Operation Of Start/Stop Button And Other RFH Functions Accompanied By Multiple RFH DTCs
21-048-24
Service Bulletin/Repair Instructions
Transfer Case Active Shift Motor Replacement Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● C1444-98 - T-Case Motor Overuse-Component Or System Over Temperature. ● C1477-4B - Transfer Case Clutch-Over Temperature. Customers may also comment on the following: ● "4WD Overheated Temporarily Unavailable" message displayed in the Instrument Panel Cluster (IPC). This bulletin involves replacing the transfer case shift motor.
100203
Warranty Program/Extension
WARRANTY OPERATIONS NEWSLETTER VOLUME 10, ISSUE 8
99985
Other
AIR BAG - DRIVER
07-007-24
Service Bulletin/Repair Instructions
Coolant Contamination / Coolant System Flush Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set the following Diagnostic Trouble Code (DTC): ● P26A3 - Engine Coolant Bypass Valve A Range-Performance. This bulletin involves flushing the cooling system and replacing the Three-way coolant valve.
S2023000024 REV.C
Service Bulletin/Repair Instructions
Water Leak Rear Of Cab Rear Seat Or Headliner
S2423000039
Service Bulletin/Repair Instructions
Wiper Motor Inoperative. Wiper Doesn’t Work or Stops Randomly On Glass
S2108000071 REV.E
Service Bulletin/Repair Instructions
Message Displayed on the Cluster, "Service Active Dampening Suspension System"
23-004-24 REV. A
Service Bulletin/Repair Instructions
Headlamp Condensation Clearing Procedure Some customers may report that on occasion, vehicle exterior head lamp assemblies are fogged with a light layer of condensation on the inside of the lenses.
9100399
Service Bulletin/Repair Instructions
MODULE Door Windows does not function at 100% or is completely inoperative. Check DTCs in DCM and check the component they are pointing to, depending on the case follow one of the procedures below: If DTC Door Lock/Unlock Switch Stuck is present: - check wiring between door module and lock/unlock switch, if there is no problem there, check lock/unlock switch and replace it. If DTC Lost communication with Master window switch is present: - check the window switch wiring, if there is no problem there, check the window switch and replace it. If DTCs related to window circuit control shorted and/or window lost calibration are present: - check Wiring between motor and hall sensor to Door module. If there is no problem there, check window seal and track to allow travel only within proper limits, reset module and perform window calibration, if problem continues, check window motor, and if needed, replace it. At the end of the procedure: Reset DDM/PDM and perform window calibration, if DTC goes stored, the repair is correct. If the window does not work replace DDM/PDM. ************DO NOT USE THIS PROCEDURE FOR REAR WINDOWS, REAR WINDOWS ARE NOT CONTROLED BY DDM or PDM***************
9100395
Service Bulletin/Repair Instructions
Shifter Binding Or "Service Shifter" Message On The Cluster. Scan the vehicle for DTCs. If one or more of the following are set, proceed to Repair. - U11E3 - TCM Lost Communication with ESM on D-PT CAN - U0103 - Loss Communication with Electric Gear Shift Module - U1267 - No Valid Data Available from ESM on CAN-C or CAN D-PT Perform the following checks. 1. Check the wiring connectors 2. Check that the connections are the battery are properly seated. 3. Disconnect and re connect the shifter 4. If the DTC is still present, erase it using the scan tool 5. If the issue is still present, do a hard reset through scan tool 6. If DTCs are still present, replace the part
99500
Other
CARRIER – PLANETARY & SHAFT KIT - OUTPUT
S2409000003
Service Bulletin/Repair Instructions
Engine Oil Leak
9100389
Service Bulletin/Repair Instructions
CAN Star Block Connector Customer finds MIL light on and technician finds DTC for loss of communication on one or more modules. In repair procedure the dealerships are replacing the CAN star block connector during their root cause process with returned parts showing no trouble found. Here is a list of steps the dealers can follow to determine if they have a defective CAN star block connector using a multimeter: Step 1: Visually review CAN star block for damage and ensure back cover has all locking tabs engaged. If a bent pin, cracked or damaged housing or locking tab is not engaged is observed then replacement is required. Step 2: Identify Connector #1 as the 3 Pin Connector cavity Step 3: Measure resistance between Pin#1 and Pin#2 in Connector #1. Acceptable values are 120.4 Ohms to 139.8 Ohms. If resistance is outside of this range then replacement is required. Step 4: Measure the continuity between Pin#1 in Connector #1 to Pin#1 in each of the other 2 Pin connector cavities. If continuity is not found then a replacement is required. Step 5: Measure the continuity between Pin#2 in Connector #1 to Pin#2 in each of the other 2 Pin connector cavities. If continuity is not found then a replacement is required.
S248A000010
Service Bulletin/Repair Instructions
Satellite Radio Displays “Satellite Hardware Error” Message
09-001-24 REV. C
Service Bulletin/Repair Instructions
Cold Engine Ticking Noise The customer may describe a ticking noise from the exhaust manifold location(s) when cold.
S2408000015 REV.C
Service Bulletin/Repair Instructions
Remote Keyless Entry (RKE) Functions Do Not Work, Intermittent Vehicle Response When Using the RKE, Key Not Programmed, Adding Remote Start
9100362
Service Bulletin/Repair Instructions
MODULE Steering Control Before replacing the steering column control module (SCCM), please follow these steps: 1.- Make sure all the switches' and airbag's harness are properly connected, disconnect the switches and reconnect them, and reverify the issue. 2.- Pull the SCCM fuse for 60 sec and then reinstall it. 3.- Reverify if Steering wheel switches are inoperative. If there are no DTC's, physical defects, nor switches inop, then SCCM does not need to be replaced.
9100381
Service Bulletin/Repair Instructions
Door Courtesy Mid RR Tech Tip: Clarification on Rear Door Lighting for DT Vehicles with Sales Code LB2 Dear Dealers, We want to provide clarity regarding the rear door lighting configuration for DT vehicles equipped with sales code LB2. It has come to our attention that there is some confusion regarding the number of lights on DT rear doors. 1. Background: In model year MY22 and earlier, DT rear doors were equipped with three lights. However, starting from MY23, DT rear doors are correctly built with only two lights. 3. Sales Code LB2: Vehicles with sales code LB2 are designed to have two lights on the rear doors. 4. Action Required: If a customer complains about missing rear door lights on an LB2-equipped vehicle, please do not order part number 68291943AC. LB2-equipped vehicles are correctly built with two lights, and adding a third light is unnecessary. Thank you for your attention to this matter. If you have any further questions or need assistance, feel free to reach out to our support team.
03-006-24
Service Bulletin/Repair Instructions
Rear Axle Vibration Shudder Or Chatter Customers may experience the following: ● A chatter, shudder, or vibration from the rear axle during turns. NOTE: This may happen more as the vehicle ages, especially if the vehicle is used extensively for towing or hauling heavy loads. The cause of the concern may be due to degradation of the rear axle fluid. It is very important to follow the routine maintenance schedules on these vehicles when it comes to changing the rear axle fluid if the vehicle is used primarily for towing or hauling heavy loads. If you experience a vehicle with the above condition, please perform the proper maintenance procedures for the rear axle and replace the fluid first before replacing any hardware components. NOTE: This service bulletin is only applicable to vehicles that have no history of an axle fluid replacement. If the vehicle usage includes police, taxi, fleet, off-road or frequent trailer towing, regular axle fluid changes are required every 3 years or 30,000 miles (whichever comes first) per the Maintenance Schedule in the vehicle Owner's Manual. This bulletin involves changing the rear axle lube to possibly address a chatter, shudder or vibration.
S2402000001
Service Bulletin/Repair Instructions
Clunking Noise From Front Stabilizer Bar / Sway Bar Link.
08-151-24
Service Bulletin/Repair Instructions
Flash: Air Suspension Control Module (ASCM) Flash Updates Customers may comment on the following: ● The air suspension is stuck in a lowered entry/exit ride height after lowering the vehicle to load the rear cargo bed of the truck and then driving on the freeway. This bulletin involves reprogramming the ASCM with the latest available software.
S2408000066
Service Bulletin/Repair Instructions
Drained Battery, Low System Voltage, Battery Not Charging, High System Voltage
96076
Other
MOTOR - WINDSHIELD WIPER & WIPERUNIT - WINDSHIELD WIPER
98927
Other
MOTOR - WINDSHIELD WIPER & WIPERUNIT - WINDSHIELD WIPER
S1408000384 REV.F
Service Bulletin/Repair Instructions
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
S2308000120 REV.B
Service Bulletin/Repair Instructions
Rain Sensing Auto Wipers and Auto on Head Lamps Inoperative
S228A000005 REV.D
Service Bulletin/Repair Instructions
Uconnect Box Error Message, With Active or Stored Cellular Antenna Open or Short Diagnostic Trouble Codes (DTCs)
S2307000002 REV.B
Service Bulletin/Repair Instructions
Suspected Engine Coolant Leak
9100354
Service Bulletin/Repair Instructions
SWITCH Multifunction Before replacing the steering column control module (SCCM), please follow these steps: 1.- Make sure all the switches' and airbag's harness are properly connected, disconnect the switches and reconnect them, and reverify the issue. 2.- Review the SCCM for any physical issue (Autolock, clockspring damaged) 3.- Pull the SCCM fuse for 60 sec and then reinstall it. 3.- Reverify if Steering wheel switches are inoperative. If there are no DTC's, physical defects, nor switches inop, then SCCM does not need to be replaced.
S2111000001 REV.B
Service Bulletin/Repair Instructions
Customer complains of a brief metallic ticking/rattling/ringing noise after a cold start-up. It can be heard while standing outside the vehicle, resonating from the front wheel well areas. If the noise is present, it is normally heard at idle and the frequency of the noise will follow engine speed.
S2423000024 REV.A
Service Bulletin/Repair Instructions
Door Ajar Light On With Door(s) Closed.
98323
Other
MODULE - TELEMATICS
98354
Other
Valve - EGR
S2423000027
Service Bulletin/Repair Instructions
Horn Sound Is Weak, Off Tone, Or Inoperative
S2408000047
Service Bulletin/Repair Instructions
Electric Start Stop (ESS) Does Not Function After a Recent Service Repair
9100338REV1
Service Bulletin/Repair Instructions
GENERATOR Engine Prior to alternator/generator removal: 1. Inspect & check all electrical connections to the alternator a. 2-way connector containing field control circuit & alternator sense voltage circuit. b. Unplug & plug-in the 2-way connector for field & sense circuit. Verify the connection is tight & check for any bent pins in alternator connector or damage to female terminals in connector. c. Check Alternator B+ Stud connection to be sure nut is securing positive cable terminal properly (i.e. nut is clamping terminal & connection is tight). d. Check fuse between the alternator B+ stud & PDC terminal to make sure it is not blown. e. Be sure to follow service manual sections on ALTERNATOR CONTROL CIRCUIT DIAGNOSTIC & ALTERNATOR SENSE CIRCUIT DIAGNOSTIC looking for any opens & shorts (to ground or battery voltage). 2. Check/verify all grounds in the charging system circuit a. Check tightness of mounting bolts securing alternator to engine block. Alternator is a case ground component. b. Check main ground from engine to chassis; connection must be tight. c. Check battery ground cable connections are tight. d. Potentially, loosen alternator mounting bolts, without removing alternator, and re-tighten to torque specifications in service manual. e. After all steps above are complete, re-start engine & check charging system operation. 3. Verify that the Smart Charging System is not the reason for alternator low voltage & current output (Amps). a. Alternator charging can be suspended during engine idle operation because of the Smart Charge strategy. b. Refer to service manual section "System Operation - Smart Charging System". c. Refer to Star Case S2008000031 Rev A for low charging voltage & Smart Charge Mode Voltage Range diagram & mode descriptions. d. The alternator has no internal regulator; thus, has no smart circuitry. All alternator control signals come from ECM. 4. If alternator is faulty, remove alternator & mounting bolts. Return alternator with bolts for analysis at QEC.
23-018-24 REV. A
Service Bulletin/Repair Instructions
Incorrect Floor Pan Installed Customer's vehicle may have been built with the following: ● Extra holes in floor pan under carpet. This bulletin involves covering open holes in the floor pan with butyl sealer and tape.
S1908000050 REV.A
Service Bulletin/Repair Instructions
Checking Radio Software Level On A VP2 Radio
S2308000151 REV. A
Service Bulletin/Repair Instructions
Key Fob Battery Low Warning Message Displayed on The Instrument Panel Cluster (IPC)
9100344
Service Bulletin/Repair Instructions
VALVE BODY & CONTROL UNIT Transmission Ensure clutch pressure check has been completed and documented prior to valve body replacement.
97960
Other
MODULE - STEERING CONTROL
97961
Other
BRUSH - VACUUM
S2408000015 REV.B
Service Bulletin/Repair Instructions
Remote Keyless Entry (RKE) Button Functions Does Not Work, Intermittent Vehicle Response When Using the RKE, Key Not Programmed
9100337
Service Bulletin/Repair Instructions
PUMP WATER For 2016-2024MY 3.6L Pentastar Upgrade with suspected coolant leak. PRIOR TO PERFORMING ANY WATER PUMP REPLACEMENT, PROCEED WITH INSPECTION INSTRUCTIONS FROM THE LATEST VERSION OF STAR ONLINE PUBLICATION S2307000002. Please submit pictures of the leak area thru the DIDI process outlined in the STAR Online document. NOTE: Some coolant residue may be found at the water pump weep hole plug area which may be normal, but coolant should not be dripping from this location. If unsure about, use the Pressurized Coolant System Inspection process as found in the Dealer Connect Cooling Diagnosis and Testing Procedures.
0803524
Service Bulletin/Repair Instructions
Battery Pack Control Module (BPCM) Software Update Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that one or more of the following Diagnostic Trouble Codes (DTC)s have been set: ? P0AC0 - Hybrid Battery Pack Current Sensor 1 Circuit Performance. ? P1A29 - Cell Supervisory Circuit A Failure. ? P0DE7 - Hybrid/EV Battery Pack Cell Voltage High. ? P0ABA - Voltage Sense A Circuit. ? P0B3D - Hybrid Battery Voltage Sense "A" Circuit Low. ? P0B3E - Hybrid Battery Voltage Sense "A" Circuit High. ? U3017 - Control Module Timer/Clock Performance. ? P0E55 - DC/DC Converter Current Sensor Circuit "A". ? P0DAF - Hybrid/EV Battery Cell Balancing Circuit "A". ? P0AD4 - Hybrid Battery Pack Air Flow System Insufficient Air Flow. This bulletin involves updating the BPCM with the latest available software.
9100301
Service Bulletin/Repair Instructions
UCONNECT 5 W 8.4" DISPLAY Prior to replacing the radio, please check for any related recalls, TSBs, or any STAR Online publications. Please verify the radio is at the latest available software level. If active DTCs are set, perform the appropriate diagnostic procedure in service information. If the condition is intermittent, refer to Section 29 Non-DTC Based Diagnostics and perform the diagnostic procedure related to the customer's complaint. If concern is still present or the customer has returned to the dealer multiple times for the same complaint, contact engineering FCA Redacted Content. If no answer or call back within 15 minutes, continue with regular diagnosis.
0900124
Service Bulletin/Repair Instructions
Cold Engine Ticking Noise The customer may describe a ticking noise from the exhaust manifold location(s) when cold. This bulletin involves replacing the exhaust manifolds.
9100287
Service Bulletin/Repair Instructions
Thermostat Assy For 2022-2024MY 3.6L Pentastar Upgrade with P0128 failure code. PRIOR TO PERFORMING ANY THERMOSTAT REPLACEMENT, PROCEED WITH INSPECTION INSTRUCTIONS FROM THE LATEST VERSION OF STAR ONLINE PUBLICATION S2309000014
0800624A
Service Bulletin/Repair Instructions
Navigation (NAV) Reboot When MOTA Fails The customer may describe one of more of the following: ? Radio navigation continues to reboot after a Map Update (MOTA). ? Navigation regularly cuts out and back on again. ? Radio switches to navigation without customer's input. This bulletin involves updating the Navigation maps via USB.
2300424
Service Bulletin/Repair Instructions
Headlamp Condensation Clearing Procedure Some customers may report that on occasion, vehicle exterior head lamp assemblies are fogged with a light layer of condensation on the inside of the lenses.
S1408000384
Service Bulletin/Repair Instructions
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
9100274
Service Bulletin/Repair Instructions
Blindspot Module For concern on Blindspot Module setting U11FB-00 Lost Communication with Left Blind Spot Sensor, U11FA-00 Lost Communication with Right Blind Spot Sensor. Some vehicle(s) where the Blindspot Module was replaced had no issues found with the Blindspot Module after testing. Please verify no wiring or connector issues are present prior to module replacement. Prior to replacing the Blindspot Module, Please Contact Engineering: FCA REDACTED CONTENT If no response in 15 minutes, please proceed with repair.
9100271
Service Bulletin/Repair Instructions
Short Runner Valve Acutator 1. Please follow service procedure before ordering SRV. 2. SRV-related DTCs are mostly related to PCM, wiring/connector damage, misconnection (loose, not attached), drained battery. Please check these conditions before ordering a new SRV.
9100279
Service Bulletin/Repair Instructions
COOLER Engine Oil Please be aware that the oil cooler seal is serviceable as a standalone part and should be considered for replacement as a remedy for fluid leak.
S2308000150
Service Bulletin/Repair Instructions
No Start, No Crank
9100276
Service Bulletin/Repair Instructions
Spring Front Upr - Isolator Before replacing this part. Please contact FCA REDACTED CONTENT. ~ If no response in 15 minutes, proceed with repair.
9100265
Service Bulletin/Repair Instructions
Hydraulic tensioner Before replacing any Front End Accessory Drive components, please check Accessory Drive belt routing as per engine sales code. Customer complaints may include a noise coming from under de hood described as a squeal, screech, squeak, chirp or "belt related" noise and/or noisy tensioner/pulley. Please check Service Library for any STAR Online publications that may apply. Note: If it is found that the pulleys and/or tensioners are to blame for the noise please use an stethoscope or similar tool to determine the origin of the noise and include it in the narrative.
9100262
Service Bulletin/Repair Instructions
SWITCH Headlamp Before replacing the Headlamp Switch, due to an issue on the I/P Dimmer. Please follow the next steps to corroborate if the Headlamp Switch is malfunctioning: 1.- Please disconnect and reconnect the headlamp Switch. And verify if the issue is corrected. 2.- Review the resistance value between Pins 6 & 3. The value should be around 5.74 KOhms, when in the lowest position to 311 ohms in the top position (Parade Detent). If a problem is found in the resistor values. Please replace the Switch.
9100247
Service Bulletin/Repair Instructions
ERG Hydraulic Tensioner Before replacing any FEAD components, please check FEAD belt layout as per the engine sales code. Customer complaint may include a noise from under the hood described as a squeal, screech, squeak, chirp or belt-related noise and/or noisy tensioner/pulley. Please refer to SOL# S2309000007.
9100241
Service Bulletin/Repair Instructions
FRT RT/LT - LAMP ASSY For moisture / water found in headlamp please review TSB 23-029-23 Headlamp Condensation clearing procedure. If the moisture problem persists: 1. Provide picture of headlamp moisture in headlamp after running the TSB. 2. Check for damage to headlamp lens, housing and flanges. Provide digital pictures of any damage found. Please make sure that pictures show location and severity of the damage is on the part. Please send the pictures along with the VIN, part number and mileage to the following: FCA Redacted Content
9100229
Service Bulletin/Repair Instructions
LIFTER, Hydraulic Roller Deactivating Please do not replace MDS lifters because the disconnecting pin is not lined up, this is normal and not a defect.
S2323000075
Service Bulletin/Repair Instructions
2nd Row Center Seat Lazy Or Slow When Folding.
9100226
Service Bulletin/Repair Instructions
Connector kit Before ordering this connector repair kit 68018957A$, check it in the Mopar Connector Repair Kit Website to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.
9100212
Service Bulletin/Repair Instructions
PUMP Water For 2016-2024MY 3.6L Pentastar Upgrade with suspected coolant leak. PRIOR TO PERFORMING ANY WATER PUMP REPLACEMENT, PROCEED WITH INSPECTION INSTRUCTIONS FROM THE LATEST VERSION OF STAR ONLINE PUBLICATION S2307000002. Please submit pictures of the leak area thru the DIDI process outlined in the STAR Online document. NOTE: Some coolant residue may be found at the water pump weep hole plug area which may be normal, but coolant should not be dripping from this location. If unsure about, use the Pressurized Coolant System Inspection process as found in the Dealer Connect Cooling Diagnosis and Testing Procedures.
S2307000002
Service Bulletin/Repair Instructions
Suspected engine coolant leak.
93023
Service Bulletin/Repair Instructions
Warranty Bulletin D-16-03 - "Can / Am" Warranty Coverage - 594 / 595 / 596 WCC (Rev. B)
93120
Service Bulletin/Repair Instructions
FCA Caribbean Warranty Bulletin ID-23-20 "Can / Am" Warranty Coverage - 594 / 595 / 596 WCC
9100195
Service Bulletin/Repair Instructions
STARTER Engine Due to starter No Trouble Found claims, please contact FCA Redacted Content prior to repair. If no response in 15 minutes, proceed with repair.
2400623
Service Bulletin/Repair Instructions
A/C Diagnostic LOP Change
9100194
Service Bulletin/Repair Instructions
EPS Steering Gear Prior to replacing EPS gear for Can C Bus Diagnostic Trouble Codes (DTCs), U0001 & U0002, please contact FCA Redacted Content. Please have the following info available: VIN, vehicle complaint, diagnostics completed, first name and last name, Dealer code, Service Manager name, Phone number or email address. If no response received in 15 minutes, proceed with part repair.
0700723
Service Bulletin/Repair Instructions
Water Quality When Mixed With Engine Coolant
9100114
Service Bulletin/Repair Instructions
Duct Assy Charge Air Cooler In If the seal is missing from inside a Henn connector, please search for the missing seal. It could have been pulled out while removal of the hose from the spigot if it was partially stuck to the spigot. It could have been blown into the hose or CAC. If that is the only concern with the CAC Hose Assembly, then replace the seal with a new replacement seal instead of replacing the entire hose assembly.