9100901
Service Bulletin/Repair Instructions
Passive Entry O/S Dr Handle Prior to replacing an inoperative passive entry door handle, perform Star Online S2623000040.
Vehicle report
Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
9100901
Passive Entry O/S Dr Handle Prior to replacing an inoperative passive entry door handle, perform Star Online S2623000040.
114254
RADIATOR - ENGINE COOLING
114255
RADIATOR - ENGINE COOLING
113854
SWITCH AND BEZEL - FRONT DOOR
113855
SWITCH AND BEZEL - FRONT DOOR
113742
SENSOR - TURBOCHARGER SPEED
113744
SENSOR - TURBOCHARGER SPEED
08-291-26
R1H UBQ/UEQ Intermittent HVAC Page Lockup Customers may experience one or more of the following: SYMPTOM: ● Intermittently the HVAC page on the Display Screen Module will change temperature and blower speed and then freeze. ● When on the HVAC page, the Display Screen Module may not respond to touch. All other pages operate as intended.
08-272-26 REV. A
Air Handling Performance Test (APT) Availability In wiTECH Technicians may experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle may SYMPTOM: exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P0234-00 - Turbocharger Overboost Condition. ● P0299-00 - Turbocharger Underboost. ● P0101-00 - Mass Air Flow Sensor "A" Circuit Performance. ● P2463-00 - Diesel Particulate Filter Restriction - Soot Accumulation Bank 1. ● P24A4-00 - Particulate Filter Restriction - Soot Accumulation Too High. ● P2262-00 - Turbocharger Boost Pressure Not Detected - Mechanical. ● P0471-00 - Exhaust Pressure Sensor 1 Performance. ● P1451-00 - Diesel Particulate Filter System Performance. ● P2457-00 - Exhaust Gas Recirculation Cooling System Performance. ● P2263-00 - Turbo Boost System Performance. ● P2459-00 - Diesel Particulate Filter Regeneration Too Frequent. ● P24A2-00 - Diesel Particulate Filter Regeneration Incomplete - Bank 1. ● P0401-00 - EGR System Performance. ● P0402-00 - EGR Flow Excessive Detected.
08-272-26
Air Handling Performance Test (APT) Availability In wiTECH Technicians may experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle may SYMPTOM: exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P0234-00 - Turbocharger Overboost Condition. ● P0299-00 - Turbocharger Underboost. ● P0101-00 - Mass Air Flow Sensor "A" Circuit Performance. ● P2463-00 - Diesel Particulate Filter Restriction - Soot Accumulation Bank 1. ● P24A4-00 - Particulate Filter Restriction - Soot Accumulation Too High. ● P2262-00 - Turbocharger Boost Pressure Not Detected - Mechanical. ● P0471-00 - Exhaust Pressure Sensor 1 Performance. ● P1451-00 - Diesel Particulate Filter System Performance. ● P2457-00 - Exhaust Gas Recirculation Cooling System Performance. ● P2263-00 - Turbo Boost System Performance. ● P2459-00 - Diesel Particulate Filter Regeneration Too Frequent. ● P24A2-00 - Diesel Particulate Filter Regeneration Incomplete - Bank 1. ● P0401-00 - EGR System Performance. ● P0402-00 - EGR Flow Excessive Detected.
113292
INJECTOR - FUEL
113293
INJECTOR - FUEL
113276
CORE – HEATER
113277
CORE – HEATER
9100803 Rev 3
Front Fog Lamp RT 1) If the lamp contains moisture, do not replace it immediately. Turn the fog lamp on for one hour and inspect it afterward. Refer to 23-008-25 Rev.A. Exterior Front Lamps Condensation Clearing Procedure for details. 2) If the fog lamp(s) do not light. Refer to Star Online Publication S2523000085 for details.
S2508000025 REV. B
Instrument Panel Cluster (IPC) and Radio Compass Display has Dashes (--)
113069
SWITCH – HEADLAMP
113070
SWITCH – HEADLAMP
9100803 Rev 1
1) If the lamp contains moisture, do not replace it immediately. Turn the fog lamp on for one hour and inspect it afterward. Refer to 23-008-25 Rev.A. Exterior Front Lamps Condensation Clearing Procedure for details. 2) If the fog lamp(s) do not light. Refer to Star Online Publication S2523000085 for details.
S2208000045 REV.D
Backup Camera Poor Image Quality Inspection
S2508000025 REV.A
Instrument Panel Cluster (IPC) and Radio Compass Display has Dashes (--)
113065
OUTLET - AIR CONDITIONING & HEATER
113066
OUTLET - AIR CONDITIONING & HEATER
9100841 Rev 1
If customer concern diagnosis leads to suspect u-joint issue with the prop shaft, u-joint service kit should be utilized to fix concern. Prop shaft replacement would not be required.
112906
BEARING - CRANKSHAFT THRUST and KIT
9100841
HD Front and Rear Prop Shafts Increase U-Joint Usage If customer concern diagnosis leads to suspect u-joint issue or failure with the prop shaft, u-joint service kit should be utilized to fix concern. Prop shaft replacement would not be required.
S268A000014
Radio/ETM is Adding Approximately 27mA Draw to Vehicle When in Logistics Mode
S1623000028 Rev. K
Outside Power Fold Rearview Mirror Noise Or Loose At Pivot. Mirror Contacts Door Window Glass In The Folded Position.
9100835
Prior to replacing an inoperative passive entry door handle, perform Star Online S2623000040.
S1623000028 REV.J
Outside Power Fold Rearview Mirror Noise Or Loose At Pivot. Mirror Contacts Door Window Glass In The Folded Position.
S2623000040
Passive Entry Exterior Door Handle Inoperative When Touched To Lock And Or Unlock.
9100831
For Dealer awareness, HD truck, eliminate 1 of 2 M8 Joints for Sidestep bracket to Body Attachment, Bolt and rivet (06102165AA, 06511062AA) per TCR # 402632, CN 80403-T18
S1623000028 REV.I
Outside Power Fold Rearview Mirror Noise Or Loose At Pivot. Mirror Contacts Door Window Glass In The Folded Position.
111478
RADIATOR - ENGINE COOLING
9100692 Rev 1
On Cummins diesel applications that are for 2019 and newer the bpro part 1BP00507AB can on occasions create a check engine light. In these situations, it is recommended to use the appropriate Mopar air filter originally installed on the vehicle. The "AC" level of the part is in development to resolve this issue. 1BP00507AB should still be usable for 2018 and older Model year Cummins engines.
9100820
Verify "Z" part number availability. Order a "Z" part number for all Exchange Orders, Warranty, Mopar, Customer Pay and Service Contract. Order "68" part number for New, Unsold units only.
08-208-26 REV. A
Radio Message "Power Surge On USB Detected" Customers may comment on the following: ● The radio displays the message: “Power surge on USB hub detected” Fig. 1. NOTE: After the message appears, no USB devices function in the hub (no charging, no data). NOTE: Hub operation does not return until the vehicle undergoes a full key cycle.
08-208-26
Radio Message "Power Surge On USB Detected" Customers may comment on the following: ● The radio displays the message: “Power surge on USB hub detected” Fig. 1. NOTE: After the message appears, no USB devices function in the hub (no charging, no data). NOTE: Hub operation does not return until the vehicle undergoes a full key cycle
S2623000032
Squeak Or Squawk Noise Coming From Either Side Door Of The Vehicle, It Could Be Just One Door Or More. The Noise Can Be Present In Either The Upper Or The Lower Hinge.
S2308000034 REV.B
No Wireless Charging Or Slow Wireless Charging
9100803
1) If the fog lamp contains moisture, do not replace it immediately. Turn the fog lamp on for one hour and inspect it afterward. Refer to 23-008-25 Rev.A. Exterior Front Lamps Condensation Clearing Procedure for details. 2) If the fog lamp(s) do not light. Refer to Star Online Publication S2523000085 for details.
S2509000005 REV.B
Light Random Tick Noise From The Engine.
S2614000002
Diagnostic Trouble Code (DTC) P2459-00 Particulate Filter Regeneration Too Frequent Setting in the Powertrain Control Module (PCM) or Under Fueling or Over Fueling Condition After Fuel Injector(s) Replacement
S1623000028 REV.H
Outside Power Fold Rearview Mirror Noise Or Loose At Pivot. Mirror Contacts Door Window Glass In The Folded Position.
18-044-26
Flash: Powertrain Control Module (PCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must SYMPTOM: exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● **P0111-00 - Intake Air Temperature Sensor 1 Circuit Range Performance Bank 1. (In Active or Stored status) ● P0071-00 - Ambient Air Temperature Sensor Performance. (In Active or Stored status) ● P0072-00 - Ambient Air Temperature Sensor Circuit "A" Low. (In Active or Stored status) ● P0073-00 - Ambient Air Temperature Sensor Circuit "A" High. (In Active or Stored status) ● P0011-00 - Bank 1 Camshaft 1 Position Timing Over Advanced Or. (In Active or Stored status) ● P25E4-00 - B Camshaft Position - Unable To Achieve Locked Position Bank 1. (In Active or Stored status) ● P05BD-00 - Stop-Start Mode Switch Range/Performance. (In Active or Stored status) ● P0116-00 - Engine Coolant Temperature Sensor 1 Performance. (In Active or Stored status) ● P062B-00 - Internal Control Module Fuel Injector Control Performance. (In Active or Stored status) ● P0604-00 - Internal Control Module Random Access Memory Ram Error. (In Active or Stored status) ● P060C-00 - Internal Control Module Main Processor Performance. (In Active or Stored status)** ● P018B-00 - Fuel Pressure Sensor "B" Circuit Range/performance. **(In Active or Stored status)** ● P1CEA-00 - Boost Side EVAP Purge System Performance. **(In Active or Stored status)** ● P06DD-00 - Engine Oil Pressure Control Circuit Performance/Stuck Off. **(In Active or Stored status)** ● P00C6-00 - Fuel Rail Pressure Too Low - Engine Cranking. **(In Active or Stored status)** ● P0300-00 - Multiple Cylinder Misfire. **(In Active or Stored status)** Customers may also experience one or more of the following: ● **Oil Level High Warning in the Instrument Panel Cluster (IPC).** ● Fully Autonomous Parking Assist (FAPA) is not deactivated when accelerator pedal is pressed. ● Vehicle is not heating up fast enough at freezi
S2208000045 REV.C
Backup Camera Poor Image Quality Inspection
S2621000003 REV.A
The vehicle will exhibit a service transmission/check engine warning indicator for the following transmission models: 845RE, 8HP45, 850RE, 8HP50, 8HP70, 8HP75, 8HP75-PHEV, 8HP75-LCV, 8HP90, 8HP95. Transmissions may exhibit the following diagnostic codes: P07E4, P1DB2, P0716, P1B14, P0733, P1D90, P1DB7, P1B13.
S2608000010
Active Diagnostic Trouble Code (DTC) B1A10-00, B1A11-00, B1A12- 00, B1A13-00-, B1A14-00, B1A15-00, B1A16-00, and B1A17-00 in The Radio Frequency Hub (RFH)
23-005-26
Windshield Wiper Blade Maintenance Customers may experience one or more of the following: SYMPTOM: ● Wiper blades that chatter/streak/jump/skip/smear or make noise while traveling across the windshield. . No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, electronic, mechanical, photocopying, or otherwise, without written permission of FCA US LLC.
S1408000384 REV.J
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
110599
SPEAKER - NONE
110600
SPEAKER - NONE
110603
SPEAKER - NONE
110604
SPEAKER - NONE
09-003-26
Cummins 6.7L Air Filter Replacement DTC P0299 Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must SYMPTOM: exhibit/set the following Diagnostic Trouble Code (DTC): ● P0299-00 - Turbocharger Underboost. Customers may also comment on the following: ● Low power/acceleration or lag condition. This bulletin involves performing an Air Handling Performance Test (APT) and possibly replacing the air filter.
S228A000025 REV.A
Harman R1H Uconnect 5 Radio Software Flash Error Codes
S268A000008
Uconnect Box Requires Service, Please Visit an Authorized Dealer Message on Display Message With DTCs B1498-13, B1498-19 or B1570-93
S1923000010 REV.A
Floor Console Center Storage Bin Door Inoperable And Or Stuck Closed.
S2423000027 REV.D
Horn Sound Is Weak, Off Tone, Inoperative, Or Intermittent.
S1408000384 REV.I
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS Related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
S2623000006
Washer Fluid Warning Lamp Illuminated When Reservoir Is Full
S2308000120 REV.F
Rain Sensing Auto Wipers and Auto on Head Lamps Inoperative. Rain Sensor Internal Failure.
S2607000002
Hemi Water Pump Coolant Leak Inspection
S2610000001
Seatbelt Slow Retraction.
S2308000120 REV.E
Rain Sensing Auto Wipers and Auto on Head Lamps Inoperative. Rain Sensor Internal Failure.
08-394-25 REV. A
Telematics Box Module (TBM) Backup Battery Replacement When DTC B1E21 Is Present Technicians may experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle may exhibit/set the following Diagnostic Trouble Code (DTC): ● B1E21-96 - Backup Battery Component Internal Failure.
08-219-25 REV. A
Telematics Box Module (TBM) Firmware Over The Air (FOTA) Software Updating from 5.39 to 5.65 *Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set the following Diagnostic Trouble Code (DTC): ● B2206-00 - Current VIN Missing / Mismatch.** Customers may experience the following: ● **SOS Unavailable message pops up on radio during a remote start event due to TBM DTC B2206-00. This bulletin provides information regarding the latest Firmware Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. The TBM software will be updated from 5.39.1 to 5.65 software level.Telematics Box Module (TBM) Firmware Over The Air (FOTA) Software Updating from 5.39 to 5.65 *Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set the following Diagnostic Trouble Code (DTC): ● B2206-00 - Current VIN Missing / Mismatch.** Customers may experience the following: ● **SOS Unavailable message pops up on radio during a remote start event due to TBM DTC B2206-00. This bulletin provides information regarding the latest Firmware Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. The TBM software will be updated from 5.39.1 to 5.65 software level.Telematics Box Module (TBM) Firmware Over The Air (FOTA) Software Updating from 5.39 to 5.65 *Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set the following Diagnostic Trouble Code (DTC): ● B2206-00 - Current VIN Missing / Mismatch.** Customers may experience the following: ● **SOS Unavailable message pops up on radio during a remote start event due to TBM DTC B2206-00. This bulletin provides information regarding the latest Firmware Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. The TBM software will be updated from 5.39.1 to 5.65 software level.
08-383-25 REV. A
Telematics Box Module (TBM) Software Updating from 5.39 to 5.65 *Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set the following Diagnostic Trouble Code (DTC): ● B2206-00 - Current VIN Missing / Mismatch.** Customers may experience the following: ● **SOS Unavailable message pops up on radio during a remote start event due to TBM DTC B2206-00. This bulletin involves reprogramming the TBM with the latest available software.Telematics Box Module (TBM) Software Updating from 5.39 to 5.65 *Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set the following Diagnostic Trouble Code (DTC): ● B2206-00 - Current VIN Missing / Mismatch.** Customers may experience the following: ● **SOS Unavailable message pops up on radio during a remote start event due to TBM DTC B2206-00. This bulletin involves reprogramming the TBM with the latest available software.
9100568 Rev 1
Order regular part number for New, Unsold and Warranty units only. Verify Z part number availability. Order a Z part number for all Exchange Orders, Mopar, customer pay and service contract.
9100734
If the DTC B1E21-96: Backup Battery-Component Internal Failure is active and customer states Popup message will show at the radio: "Battery of Uconnect Box requires service. SOS call and related functions may be unavailable. Please visit an authorized dealer." PLEASE do not Replace the TBM module, only replace TBM Internal Battery (inside Telematics Box Module) and order PN68493347
9100735
Verify "Z" part number availability. Order a "Z" part number for all Exchange Orders: Warranty, Mopar, Customer pay and Service contract. Order"68" part number for New unsold units only
S2505000003
Diagnostic Trouble Code (DTC) C0050-00-Brake System Hydraulic Leak Set After Recent Repair.
08-394-25
Telematics Box Module (TBM) Backup Battery Replacement When DTC B1E21 Is Present echnicians may experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle may exhibit/set the following Diagnostic Trouble Code (DTC): ● B1E21-96 - Backup Battery Component Internal Failure
S258A000021
Diagnostic Trouble Code (DTC) B15A1-00 Media Port Connection 1 Connection Found Set.
08-383-25
Telematics Box Module (TBM) Firmware Over The Air (FOTA) Software Updating from 5.39 to 5.65 Customers may experience the following: ● No connectivity. This bulletin involves flashing the TBM to the latest software level in the case that the FOTA did not function.
S2524000014
Heated Seats And Heated Steering Wheel Inoperative
S2308000034 REV.A
No Wireless Charging Or Slow Wireless Charging
108458
DETECTOR - EVAPORATIVE SYSTEM INTEGRITY MODULE
108461
DETECTOR - EVAPORATIVE SYSTEM INTEGRITY MODULE
S2503000004
Front Axle Disconnect (FAD) Electrical Connector Design Change On Replacement Axle Assemblies.
108409
CORE - HEATER
108410
CORE - HEATER
S2508000100
Intermittent Uconnect Box Requires Service Message. TBM Setting Stored Or Pending DTCs B22A9, B1560, B1561, B1562
9100678
1. General Parts Update The recommended air filter for 2019 Model Year (MY) and newer 6.7L Cummins equipped vehicles has been updated. New Part: 68645327AA (Non-Oiled Air Filter) Replaces: 53034051AA (Oiled Air Filter) - This part is superseded and should no longer be installed. The air filter for all other applications remains unchanged: Continue to use 68517554AA for: All 2018 MY and older 6.7L Cummins equipped vehicles. All 2019 MY and newer vehicles with non-6.7L engines. 2. Special Service Procedure for DTC P0299 Application: 2019-2024 MY HD Trucks with 6.7L Diesel (ETM/ETN) Condition: If DTC P0299 is active and the vehicle is equipped with the previous oiled air filter (PN# 53034051AA). Procedure: Replace the oiled air filter (53034051AA) with the new non-oiled filter (68645327AA). Service Catalog reflects these updated usages.
08-350-25
Air Handling Performance Test (APT) Availability In wiTECH Technicians may experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle may exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P0234-00 - Turbocharger Overboost Condition. ● P0299-00 - Turbocharger Underboost. ● P0101-00 - Mass Air Flow Sensor "A" Circuit Performance. ● P2463-00 - Diesel Particulate Filter Restriction - Soot Accumulation Bank 1. ● P24A4-00 - Particulate Filter Restriction - Soot Accumulation Too High. ● P2262-00 - Turbocharger Boost Pressure Not Detected - Mechanical. ● P0471-00 - Exhaust Pressure Sensor 1 Performance. ● P1451-00 - Diesel Particulate Filter System Performance. ● P2457-00 - Exhaust Gas Recirculation Cooling System Performance. ● P2263-00 - Turbo Boost System Performance. ● P2459-00 - Diesel Particulate Filter Regeneration Too Frequent. ● P24A2-00 - Diesel Particulate Filter Regeneration Incomplete - Bank 1. ● P0401-00 - EGR System Performance. ● P0402-00 - EGR Flow Excessive Detected
S2516000001
Driveline Vibration. Prop Shaft Diagnostic Information.
09-029-25
Cummins Valvetrain Noise Diagnostics Customers may comment on one or more of the following: ● Ticking noise. ● Clicking noise. ● Engine noise.
9100692
On Cummins diesel applications that are for 2019 and newer the bpro part 1BP00507AB can on occasions create a check engine light. In these situations, it is recommended to use the appropriate Mopar air filter (57008652AA). The "AC" level of the part is in development to resolve this issue. 1BP00507AB should still be usable for 2018 and older Model year Cummins engines.
S2522000003
Tire Pressure Monitor (TPM) Warning Lamp On Or Flashing. Sensor(s) Not Reading And Or Showing Dashes.
S2323000020 REV.B
Power Side Steps Reverse, Stop In Motion, And/Or Do Not Deploy Or Stow
23-008-25 REV. A
Exterior Front Lamps Condensation Clearing Procedure *Some customers may report that on occasion vehicle exterior front lamps (headlamps, fog lamps, grille lamps, logo lamps or signature lamps) assemblies are fogged with a light layer of condensation on the inside of the lenses*
02-002-25 REV. A
Shock And Strut Diagnosis And Replacement Guidelines Leaking, noisy, or weak shocks or struts.
18-081-25
Flash: Powertrain Control Module (PCM) Updates **Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P245D-00 - EGR Cooler Bypass Control Circuit High. ● P02E3-00 - Diesel Intake Air Flow Control Circuit High. ● P0490-00 - EGR Control Circuit High. ● P229F-00 - Aftertreatment NOX Sensor Circuit Performance - Bank 1 Sensor 2. ● P0299-00 - Turbocharger Underboost. ● P242F-00 - Diesel Particulate Filter Restriction - Ash Accumulation. ● P0128-00 - Thermostat Rationality. ● P0234-00 - Turbocharger Overboost Condition.** Customers may also comment on one or more of the following: ● **Engine speed unstable when vehicle is stationary, not in gear and running on high speed governor (max engine speed).** ● Longer crank time than normal. ● Transmission overheat conditions with a message displayed in the Instrument Panel Cluster (IPC) stating "Transmission oil temperature is too hot" This bulletin involves reprogramming the Engine Control Module (ECM/PCM) with the latest available software.
S2509000005 REV.A
Light Random Tick Noise From The Engine
31-001-25 REV. B
Aluminum Body Panel Corrosion Repair Aluminum corrosion or bubbling along the leading edge of hood, hinges or other exterior surface areas of the hinges, doors, fenders, swing gates or liftgates.
31-001-25 REV. A
Aluminum Body Panel Corrosion Repair Aluminum corrosion or bubbling along the leading edge of hood, hinges or other exterior surface areas of the hinges, doors, fenders, swing gates or liftgates.
31-001-25
Aluminum Body Panel Corrosion Repair Aluminum corrosion or bubbling along the leading edge of hood, hinges or other exterior surface areas of the hinges, doors, fenders, swing gates or liftgates
9100642
When customer complaint is related to inoperative 4 Wheel Drive shifter, loss of 4WD function and/or 4WD related MIL please reference SOL Case #S2508000062 prior to replacement of Transfer Case shift motor.
S258A000017
Door speaker Inoperative or No Sound
S2508000062
Unresponsive 4WD Shifter, Service 4WD Light Illuminated. ABS And/Or Traction Control Lights May Also Be On
106241
LAMP - DOME
18-066-25
Not applicable to vehicles built for US market. Flash: Powertrain Control Module (PCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P0868-00 - Transmission Fluid Pressure Low. ● P0933-00 - Hydraulic Pressure Sensor Range/performance ● P0735-00 - Gear 5 Shift Incorrect Ratio. ● P0729-00 - Gear 6 Shift Incorrect Ratio. Customers may also experience one or more of the following: ● While driving the vehicle, the Instrument Panel Cluster (IPC) is showing a transmission overheat message. ● Check engine light illuminates and will turn on and off while driving. This bulletin involves inspecting and possibly reprogramming the PCM with the latest available software.
23-006-25 REV. B
Windshield Wiper Blade Maintenance Customers may experience one or more of the following: ● Wiper blades that chatter/streak/jump/skip/smear or make noise while traveling across the windshield.
S2422000001 REV.D
Tire Pressure Monitor (TPM) Service Information. TPM Lamp On.
08-221-25
115V Power Outlet LED Always On The amber LED remains continuously illuminated, regardless of whether the switch button is activated. This bulletin involves replacing the inverter switch.
08-219-25
Telematics Box Module (TBM) Over The Air Software Update From 5.39.1 To 5.65 Customers may experience the following: ● 'SOS unavailable' popup message. This bulletin provides information regarding the latest Firmware Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. The TBM software will be updated from 5.39.1 to 5.65 software level.
105648
MODULE - ENGINE CONTROLLER
S2523000062
Bumper Mounted 7 Pin Trailer Tow Connector
104974
LAMP - DOME
105590
Warranty Newsletter – Volume 11, Issue 6
105591
FCA Caribbean Warranty Newsletter – Volume 11, Issue 6
OTHERDOC_132
Global Telematics Box Module Over The Air Update from 5.39.1 to 5.65 TBM2.0 Software Version (FOTA) Customers may experience one or more of the following: - Error display of "Uconnect Box Requires Service/Wifi Unavailable" popups; [ TBM DTC B22A9-96 Internal Performance Failure ]. - Error display of "Uconnect Box Requires Service" pop-ups; [ TBM DTCs B1560, B1561, B1562 - Antenna loose connection ].
08-182-25
Power Seat Not Adjusting Customers may experience one or more of the following: ● Driver and/or passenger seat moves backwards but not forward. ● Driver and/or passenger seat inoperative. This bulletin involves replacing the front power seat adjusters.
14-010-25 REV. B
Frequent Repairs Of Fuel System Components Such As Fuel Filters Numerous Stellantis vehicles having fuel line components replaced such as fuel filter. Occasionally, components are replaced before their standard life expectancy or when not contaminated with debris
14-010-25 REV. A
Frequent Repairs Of Fuel Line Components Such As Fuel Filters Numerous Stellantis vehicles having fuel line components replaced such as fuel filter. Occasionally, components are replaced before their standard life expectancy or when not contaminated with debri
S2509000005
Light Random Tick Noise From The Engine.
104970
CORE - HEATER
105322
D-19-02 Rev. L Fast Feedback Program - 6.7L Cummins Complete Engine, Long Block & Short Block - 2019 - 2024 HD Ram - (D2/DD/DF/DJ/DP)
9100592
LAMP Courtesy/Ambient Courtesy / Ambient Lamp: Light guide not fully seated into the retainer during IP sub-assembly due to inconsistent operator installation effort, leading to latent BSR issue that manifests under customer usage conditions. Solution: remove and reinstall light guide to be fully seated in the bracket retainer.
S2503000003
Rear Axle Locker Inoperative, Service Axle Locker Message Displayed. Discussion: Some customers may experience a, inop rear axle locker, and Service Axle Locker message. After further investigation, the technician may not find any diagnostic trouble codes (DTCs) set. However, intermittently, they may find the following DTCs set in the Drivetrain Control Module (DTCM). • C141C-11 Rear Differential Control Circuit Short To Ground. • C141C-13 Rear Differential Control Circuit Open. If the technician is working on a vehicle with the above condition, please perform the repair procedure below. Repair Procedure: 1. Remove the rear differential cover. 2. Inspect the e-locker actuator wiring harness for damage due to contact with the differential.
9100598
Module, Urea Pump/Level: HD 6.7L (ETL/ETN/ETM) with Mil On P21C4-00 (Reductant Line Heater Relay Control Circuit High / U11C1-00 (Reductant Control Module Received Implausible Data From ECM/PCM), do not replace the DEF Pump. Follow TSB's released and appropriate Service Diagnostics.
02-002-25
Shock And Strut Diagnosis And Replacement Guidelines Leaking, noisy, or weak shocks or struts.
9100562
Frame - Front Seat Back: 2024 2025 DJ D2 Power back frame with INOP motor replaced seat frame Please review TSB 08-159-25 before replacing any parts on the seat back frame.
9100574
Radio: Capture software version from radio. Record or document software version prior to troubleshooting, as soon as any infotainment issue has been found or reported. Also always document in claim. Steps to capture Radio version number: 1. Go to "Vehicle" 2. Go to "Settings" 3. Go to "System Information" 4. Find the radio version from "Version information" Example software version: U37.2, U39.4, etc.
14-010-25
Frequent Repairs Of Fuel Line Components Such As Fuel Filters Numerous Stellantis vehicles having fuel line components replaced such as fuel filter. Occasionally, components are replaced before their standard life expectancy or when not contaminated with debris
S2508000039
Universal Garage Door Opener (UGDO) Inoperative, LED Indicator Lamps Not Illuminating
S2308000120 REV.D
Rain Sensing Auto Wipers and Auto on Head Lamps Inoperative
S2323000002 REV.A
Washer Light On And Will Not Turn Off After Adding Washer Solvent.
9100579
Parking Brake Pad When replacing the park brake pedal pad, please use the correct labor operation code. Some technicians have been using the brake pedal pad labor code which is not the same as the parking brake pedal pad. The correct labor operation code should be for parking brake pedal pad replacement is 05-05-06-01.
103774
LAMP - DOME
9100568
DISPLAY Order regular part number for New unsold and Warranty units only. Verify Z part number availability. Order a Z part number for all Exchange Orders: Mopar, customer pay and service contract.
S2308000120 REV.C
Rain Sensing Auto Wipers and Auto on Head Lamps Inoperative
S258A000014
SOS Unavailable Message Pop Up On Radio During A Remote Start Event.
104526
SWITCH - STEERING WHEEL RIGHT & LEFT
9100548
ADJUSTER Seat DJ D2 DP 1st Row Power Seat Fore/Aft Adjuster Inspection TSB is also released for this concern. SYMPTOM/CONDITION: Fore-aft function does NOT work when actuating the seat switch. DIAGNOSIS: 1) Put seat in position for inspection. 2) Disconnect seat wire harness motor connector from the fore-aft motor on the seat adjuster, wait 10 seconds, and reconnect. 3) Verify function of the fore/aft adjuster. Step 1. Open 2nd row door and function rear seat cushions up to stowed position. Step 2. Adjust the driver front seat to the full up position. Use switches on the side shield to move power seat fully up. Step 3. Remove the 4 bolts that hold the seat to the truck floor and discard. The bolts have lock patch that is not reusable. Step 4. Lay the seat down so its laying on its back so the underside of the seat is easily accessible. Step 5. Remove the fore/aft wire harness motor connector from the fore/aft motor (back right of the seat adjuster). Push on the tab to remove the motor wire harness connector from the motor. Leave disconnected for 10 seconds. Step 6. Reconnect the fore/aft wire harness motor connector to the fore/aft motor. Push / Pull / Push the connector with fingers to ensure the wire harness connector is fully seated to the fore/aft motor connector. Step 7. Before assembling the seat back to the truck floor, cycle the seat to check that the motor is working properly by pressing the fore/aft switch. If fore/aft motor does not function, please refer to Replacement Procedure below. Step 8. If the seat is working properly, carefully reassemble the seat back to the truck floor using the four new bolts. Use a torque wrench to verify 47 Nm. Step 9. *Note: Checking the passenger seat will be the same procedure as the driver seat. REPLACEMENT PROCEDURE Only for seats rejected after inspection. Replace Power Seat Adjuster per MOPAR service part replacement instructions. MOPAR Part Numbers: 68455847AA, 68455848AA, 68455849AA
9100547
Telematics Box Module Verify Z part number availability. Order a Z part number for all Exchange Orders: warranty, Mopar, customer pay and service contract. Order regular part number for New unsold units only.
09-004-25 REV. A
Clicking Noisse from Engine At Idle Customers may comment on the following: ● A clicking noise from the engine at idle. This bulletin involves adding oil system protection and letting the engine idle.
104558
FCA Caribbean Warranty Newsletter – Volume 11, Issue 4
104557
Warranty Newsletter – Volume 11, Issue 4
S2523000024
Rear Defogger Solder Terminals Detached.
S2408000015 REV.D
Remote Keyless Entry (RKE) Functions Do Not Work, Intermittent Vehicle Response When Using the RKE, Key Not Programmed, Adding Remote Start
9100508
6 CONTROL UNIT, Diesel Exhaust Customer complaints with malfunction light illuminated on 2019 thru 2024 MY DJ / D2 / DD / DP vehicles with 6.7L (ETL / ETM / ETN) built on or before October 15,2024 and exhibiting DTCs P21C4-00 (Reductant Line Heater Relay Control Circuit High) and / or U11C1-00 (Reductant Control Module received implausible Data from ECM / PCM). These DTCs will occur after installation of service DCU 68458603AB. Do not replace parts until after the TSB 25-008-24 is performed. If the DTC(s) continue to set, then follow the Service Diagnostics for the applicable DTC.
09-004-25
Clicking Noise From Engine At Idle Customers may comment on the following: ● A clicking noise from the engine at idle. REPAIR SUMMARY: This bulletin involves adding oil system protection and letting the engine idle.
S258A000005 REV.A
Trailer Tow App Gauges Not Showing Data in Widget Screen
S2423000027 REV.C
Horn Sound Is Weak, Off Tone, Inoperative, Or Intermittent.
103772
SWITCH - STEERING WHEEL RIGHT & LEFT
S2409000002 REV.A
Perceived Oil Leak From The Rear Of The Engine
S1625000002 REV.B
Malfunction Indicator Lamp (MIL) Illumination, Diagnostic Trouble Codes (DTCs) P21C4 – (Diesel Exhaust Fluid) Reductant Line Heater Control Circuit High, and U11C1 – Reductant Control Module Received Implausible Data From ECM/PCM, Set
S258A000009
Apple CarPlay Does Not Complete The First Initial Wireless Connection.
03-001-25 REV. B
Clicking Noise While In 4WD Customers may experience the following: ● Ratcheting, click, or clicking noise in 4WD while turning. This bulletin involves replacing the front driveshaft.
S2108000015 REV.J
Uconnect Box Require Service Message
08-050-25
Flash: Air Suspension Control Module (ASCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set the following Diagnostic Trouble Code (DTC): ● C2202-00 - Original VIN Mismatch/missing. Customers may also experience: ● "Service air suspension" icon light may be on and system may be defaulting to normal ride heigh This bulletin involves updating the ASCM with the latest available software.
9100500
Touchscreen For all infotainment system repairs (touchscreens, radios, etc.), refurbished parts may be available. Follow the Infotainment Ordering guide available under the "Parts" section of Dealer Connect: DealerCONNECT> Parts> News& Information> Audio & Electronic Products Exchange Process
103288
CAMERA - REAR VIEW
103289
CAMERA - REAR VIEW
103291
PANEL - B PILLAR LOWER TRIM
S228A000005 REV.E
Uconnect Box Error Message, With Active or Stored Cellular Antenna Open or Short Diagnostic Trouble Codes (DTCs)
9100493
SWITCH AND BEZEL Front Door Before replacing the Window Switch/Mirror Switch, please follow these steps: 1.- Check for what DTC are detected and take proper steps acceding to the DTC's. 2.- Make sure all the switches are properly connected to their harness, disconnect the switch and reconnect it. 3.- Review the window Switch for any physical issue (Button stuck, broken) If after performing these steps the switch remains faulty. Follow suggested repairs per diagnostics performed.
S258A000005
Trailer Tow App Gauges Not Showing Data in Widget Screen
102940
CONVERTER - CATALYTIC
103214
CONVERTER - CATALYTIC
9100393 Rev 1
TRANSFER CASE BW 44-46 If fluid leak is present between the transfer case and the rear driveshaft on a 4WD vehicle the Output Shaft Seal should be considered in lieu of entire transfer case or driveshaft replacement. In the case of major damage to components, contact StarCenter and/or proceed with replacements as necessary.
9003980
SWITCH Headlamp Before replacing the Headlamp Switch for faulty dimmer operation. Please follow the next steps to corroborate if the Headlamp Switch is malfunctioning: 1.- Please disconnect and reconnect the headlamp Switch. And verify if the issue is corrected. 2.- Review the internal resistance of the switch: a.- For the Right Dimmer (IP) between Pins 6 & 3. The value should be around 5.74 KOhms, when in the lowest position to 311 ohms in the top position (Parade Detent). b.- For the left Dimmer (Ambient Light) between pins 8 & 3. The value should be around 14.52 KOhms, when in the lowest position to 182 ohms in the top position. If a problem is found in the resistor values. Please replace the Switch.
S1408000384 REV.H
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS Related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
S1425000019 REV.A
Malfunction Indicator Lamp (MIL) Illuminated. Diesel Exhaust Fluid (DEF) System Diagnostic Trouble Codes (DTCs) due to Hydrocarbon Contamination.
9100490
SWITCH Instrument Panel Before replacing the driver window switch, please follow these steps: 1.- Review the Trailer brake Switch for any physical issue (Button stuck, broke). If no physical issue identified, move to next steps. 2.- Make sure the switch harness is properly connected, disconnect the switch and reconnect it, and reverify the issue. 3.- Check for what DTC are detected and take proper steps. 4.- Review the internal resistance of the switch to corroborate if it is shorted: a) Between Pins 10&2 it should be around 13ohms +/- 4ohms b) Between Pins 3 & 4 and 4 & 6, 160 ohms +/-10 Ohms If a problem is found in the resistor values. Please replace the Switch.
9100487
MODULE Steering Control Before replacing the steering column control module (SCCM) due to turn signal inop, wipers inop, steering controls inop, TCS light DTC C0051 or horn blowing while turning, please follow these steps: 1.- Refer to service library procedure and follow diagnosis steps. 2.- If failure still present, make sure all the switches', horn's, airbag's harness are properly connected and there is no corrosion or pinching, disconnect the switches & reconnect them, and reverify the issue. 3.- Verify if failure is still present, review if there is lack of communication between SCCM and BCM. For example, activate turn signals or wipers. 4.- Read at the BCM diagnosis session if BCM is receiving information from SCCM. Through diagnosis review if activation from horn, wipers or turn signal is requested and are working. 5.- Disconnect the SCCM fuse for around 30s,and repeat the previous steps to see if failure still present. 6.- Do a hard reset to BCM and evaluate if any DTC is set. Retest if failure still present. 7.- Before replacing the SCCM disconnect it and reconnect it again. If there are no DTC's active, physical defects, steering controls inop, wipers inop, nor turn signal inop, horn inop, then SCCM does not need to be replaced.
S2523000002
Outside Exterior Mirror Power Extend And/Or Retract Is Not Fully Functional.
S1408000384 REV.G
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
S2310000003
The customer may experience an airbag light on or seat belt chime when buckled.
102387
SEAL - OUTPUT SHAFT
S2008000186 REV.B
Engine Control Module (ECM) Flash Failure, Diagnostic Trouble Code (DTC) U1601 – ECU Application Software Code 1 Missing Or Corrupted
102307
GEAR - REACTION SUN
S2408000123
Push to Start Button Has a Delay Switching Ignition Positions, DTCs (Diagnostic Trouble Codes), B1A7D-2A Start Button - Stuck, U103C-00 KIN/IGNM Communication
9100459
switch Electronic range select Before replacing the switch electronic gear selector 68379834AB due to P0826-29, P0826- 11 active codes, please follow these steps: 1.- Refer to service library procedure and follow diagnosis steps at BCM. 2.- If failure still present, make sure the switch is properly connected and there is no corrosion or pinching, disconnect the switch & reconnect it, and reverify the issue. 3.- Verify if failure is still present, review if there is lack of communication between gear selector switch and BCM. For example, try switching between driving modes. 4.- Read at the BCM diagnosis session if BCM is receiving information from gear selector. 5.- Do a hard reset to BCM and evaluate if any DTC or failure code is set. Retest if failure still present. If there are no DTC's, physical defects, gear selector inop, then the Electronic Gear Selector Switch does not need to be replaced.
9100462
SWITCH Mirror Before replacing the driver window switch, please follow these steps: 1.- Review the telescopic mirror Switch for any physical issue (Button stuck, broke). If no physical issue identified, move to next steps. 2.- Make sure the switch harness is properly connected, disconnect the switch and reconnect it, and reverify the issue. 3.- Check for what DTC are detected and take proper steps. If there are no DTC's nor physical defectives, then the telescopic mirror switches can't be replaced.
9100465
SEAT BELT Front Outer Seatbelt Slow Retraction / Seat Belt Cleaning If the vehicle exhibits slow seatbelt retraction, prior to replacing seatbelt please inspect for debris and any build up on the webbing and DRing. If evidence of debris and build up, please clean seatbelt webbing or turning loop as described below. Seat Belt Maintenance: Do not bleach, dye or clean the belts with chemical solvents or abrasive cleaners. This will weaken the fabric. If the belts need cleaning, use a mild soap solution or lukewarm water. Do not remove the belts from the vehicle to wash them. Dry with a soft cloth. Sun damage can also weaken the fabric. Replace the belts if they appear frayed or worn or if the buckles do not work properly. NOTE: If the belts retract slowly, inspect the upper turning loop for soiling. If soiling is present, clean with a wet soft cloth until all residue is removed.
S2208000045 REV.B
Backup Camera Poor Image Quality Inspection
S248A000018
Trailer Tow Pages App Gauges Not Showing Data After Radio Update
101683
CONVERTER - CATALYTIC
101773
CONVERTER - CATALYTIC
25-008-24
Flash: Diesel Exhaust Fluid (DEF) Dosing Control Unit (DCU) Update Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set the following Diagnostic Trouble Code (DTC): ● P21C4-00 - Reductant Line Heater Relay Control Circuit High. ● U11C1-00 - Reductant Control Module Received Implausible Data From ECM/PCM. These DTCs will occur after installation of service DCU 68458603AB. This bulletin involves reprogramming the DCU with the latest available software.
S2422000001 REV.C
Tire Pressure Monitor (TPM) Service Information. TPM Lamp On.
101232
Plate - Planetary
101092
TRANSMISSION KIT - WITH TORQUE CONVERTER
101094
TRANSMISSION KIT - WITH TORQUE CONVERTER
25-005-24 REV. B
Diesel Particulate Filter (DPF) Trying To Regen Too Frequent Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set the following Diagnostic Trouble Code (DTC): ● P2459 - Diesel Particulate Filter Regeneration Too Frequent. Customers may also experience the following: ● Vehicle has entered engine performance de-rate mode. NOTE: Engine performance de-rate mode will occur when DTC P2459 has been set for a long period. This bulletin involves replacing the DPF if DTC P2459 is set.
25-005-24 REV. A
Diesel Particulate Filter (DPF) Trying To Regen Too Frequent Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set the following Diagnostic Trouble Code (DTC): ● P2459 - Diesel Particulate Filter Regeneration Too Frequent. Customers may also experience the following: ● Vehicle has entered engine performance de-rate mode. NOTE: Engine performance de-rate mode will occur when DTC P2459 has been set for a long period. This bulletin involves replacing the DPF if DTC P2459 is set.
S2422000003
Trailer Tire Pressure Monitor (TTPM) Programming Tips And Operation Information.
100498
MODULE - ENGINE CONTROLLER
S2423000043
Dome Lamp LED And Incandescent Bulb Servicing.
100774
SWITCH - HEADLAMP
97802
SWITCH - HEADLAMP
25-005-24
Diesel Particulate Filter (DPF) Trying To Regen Too Frequent Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P2459 - Diesel Particulate Filter Regeneration Too Frequent. Customers may also experience the following: ● Vehicle has entered engine performance de-rate mode. NOTE: Engine performance de-rate mode will occur when the DTC has been set for a long period. This bulletin involves replaceing the DPF if DTC P2459 is set.
S2208000153 REV.B
Tire Pressure Lamp Flashing, No Tire Pressures Displayed, “Tire Pressure Module (TPM) System Unavailable” Message Displayed on Cluster
100595
WARRANTY BULLETIN D-24-15 announces the addition of the Rear Axle Assembly replacement for 2019 - 2024 RAM 3500 Cab Chassis (DD), RAM 4500/ 5500 Cab Chassis (DP), RAM 3500 Pickup (D2), RAM 2500 Pickup (DJ), RAM 1500 Pickup (DS) and RAM 1500 Pickup (DT) vehicles to the Powertrain Pre-Authorization program for all dealers (Base, Plus & Premium) to ensure proper repair of Rear Axle Assembly failures and to assist in quality improvements. REV.A
100599
FCA Caribbean Warranty Bulletin ID-24-16 Rev. Announces the addition of the Rear Axle Assembly replacement for 2019 - 2024 RAM 3500 Cab Chassis (DD), RAM 4500/ 5500 Cab Chassis (DP), RAM 3500 Pickup (D2), RAM 2500 Pickup (DJ), RAM 1500 Pickup (DS) and RAM 1500 Pickup (DT) vehicles to the Powertrain Pre-Authorization program to ensure proper repair of Rear Axle Assembly failures and to assist in quality improvements. REV.A
S228A000017 REV.A
Battery Drain Suspected or "Identified" From USB or Media Hub
08-197-24
Right Busbar Cover Modification For Service Battery Clearance The technician or customer may experience: ● While installing the Mopar service battery as a replacement for the factory battery, there is an interference issue with the right busbar cover on the positive terminal side of the battery. This bulletin involves modifying the right busbar cover on the positive terminal side of the battery.
S2423000027 REV.A
Horn Sound Is Weak, Off Tone, Or Inoperative.
99985
AIR BAG - DRIVER
S2423000039
Wiper Motor Inoperative. Wiper Doesn’t Work or Stops Randomly On Glass
08-173-24
Radio Over The Air Update to T27.46 Software Version Customers may also experience one or more of the following: ● Navigation signal drops out. Maps not loading on the Instrument Panel Cluster (IPC) display. ● Cannot change satellite stations, display shows one station on screen but is playing another. ● Battery drain. ● A Black screen after clicking accept at start up (Rearview camera functions normally). ● Radio resets (Rearview camera functions normally). ● Wireless connectivity disconnecting. ● CarPlay® icon does not appear in device manager. ● Audio disruptions. ● SXMT inoperative. ● Audio mute. ● Passenger screen blank. ● Passenger screen apps missing. ● Missing profiles icon. ● IPC displays incorrect audio source. ● Radio is slow to respond. ● Trailer tire pressure configurations deleted. ● Steering wheel controls skipping SXMT channels. ● Recent calls not displayed. ● Phone audio playing when ignition is off. In addition, the following software enhancement(s) are available: ● Icon size/layout improvements. ● Carplay/Android Auto® improvements. ● Uconnect Phone improvements. ● FOTA improvements. ● Passenger screen camera app improvements. ● Voice Recognition (VR) command improvements. This bulletin provides information regarding the latest FOTA update and provides the service technician an overview of the steps a customer will need to take to complete the update. The radio software will be updated from T25.48 or T25.51 to T27.46.
S248A000011
Driver Hears Noise, Static or Can Not Hear Phone Caller on Other End
31-001-24
Aluminum Body Panel Corrosion Repair Aluminum corrosion or bubbling along the leading edge of hood, hinges or other exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: Verify current warranty policy to determine if digital imaging pre-authorization is required or pre-approval is required from the Regional Office; depending on market. This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.
9100393
TRANSFER CASE BW 44-46 If fluid leak is present between the transfer case and the rear driveshaft on a 4WD vehicle the Output Shaft Seal - service part numbers 68161329AA OR 68449218AA (max tow application) - should be considered in lieu of entire transfer case or driveshaft replacement. In the case of major damage to components, contact StarCenter and/or proceed with replacements as necessary
9100389
CAN Star Block Connector Customer finds MIL light on and technician finds DTC for loss of communication on one or more modules. In repair procedure the dealerships are replacing the CAN star block connector during their root cause process with returned parts showing no trouble found. Here is a list of steps the dealers can follow to determine if they have a defective CAN star block connector using a multimeter: Step 1: Visually review CAN star block for damage and ensure back cover has all locking tabs engaged. If a bent pin, cracked or damaged housing or locking tab is not engaged is observed then replacement is required. Step 2: Identify Connector #1 as the 3 Pin Connector cavity Step 3: Measure resistance between Pin#1 and Pin#2 in Connector #1. Acceptable values are 120.4 Ohms to 139.8 Ohms. If resistance is outside of this range then replacement is required. Step 4: Measure the continuity between Pin#1 in Connector #1 to Pin#1 in each of the other 2 Pin connector cavities. If continuity is not found then a replacement is required. Step 5: Measure the continuity between Pin#2 in Connector #1 to Pin#2 in each of the other 2 Pin connector cavities. If continuity is not found then a replacement is required.
S248A000010
Satellite Radio Displays “Satellite Hardware Error” Message
S2409000002
Perceived Oil Leak From The Rear Of The Engine
S2408000015 REV.C
Remote Keyless Entry (RKE) Functions Do Not Work, Intermittent Vehicle Response When Using the RKE, Key Not Programmed, Adding Remote Start
9100362
MODULE Steering Control Before replacing the steering column control module (SCCM), please follow these steps: 1.- Make sure all the switches' and airbag's harness are properly connected, disconnect the switches and reconnect them, and reverify the issue. 2.- Pull the SCCM fuse for 60 sec and then reinstall it. 3.- Reverify if Steering wheel switches are inoperative. If there are no DTC's, physical defects, nor switches inop, then SCCM does not need to be replaced.
03-006-24
Rear Axle Vibration Shudder Or Chatter Customers may experience the following: ● A chatter, shudder, or vibration from the rear axle during turns. NOTE: This may happen more as the vehicle ages, especially if the vehicle is used extensively for towing or hauling heavy loads. The cause of the concern may be due to degradation of the rear axle fluid. It is very important to follow the routine maintenance schedules on these vehicles when it comes to changing the rear axle fluid if the vehicle is used primarily for towing or hauling heavy loads. If you experience a vehicle with the above condition, please perform the proper maintenance procedures for the rear axle and replace the fluid first before replacing any hardware components. NOTE: This service bulletin is only applicable to vehicles that have no history of an axle fluid replacement. If the vehicle usage includes police, taxi, fleet, off-road or frequent trailer towing, regular axle fluid changes are required every 3 years or 30,000 miles (whichever comes first) per the Maintenance Schedule in the vehicle Owner's Manual. This bulletin involves changing the rear axle lube to possibly address a chatter, shudder or vibration.
S2408000066
Drained Battery, Low System Voltage, Battery Not Charging, High System Voltage
96076
MOTOR - WINDSHIELD WIPER & WIPERUNIT - WINDSHIELD WIPER
98927
MOTOR - WINDSHIELD WIPER & WIPERUNIT - WINDSHIELD WIPER
94006
WIPERUNIT - WINDSHIELD WIPER, BLADE - FRONT WIPER
98861
WIPERUNIT - WINDSHIELD WIPER, BLADE - FRONT WIPER.
08-141-24
Flash: Memory Seat Module (MSM) Updates Customers may experience the following: ● Telescoping Mirrors are inoperative. This bulletin involves reprogramming the MSM with the latest available software.
S2308000120 REV.B
Rain Sensing Auto Wipers and Auto on Head Lamps Inoperative
98599
MODULE - ANTI-LOCK BRAKE SYSTEM
S228A000005 REV.D
Uconnect Box Error Message, With Active or Stored Cellular Antenna Open or Short Diagnostic Trouble Codes (DTCs)
98550
MODULE - ANTI-LOCK BRAKE SYSTEM
98323
MODULE - TELEMATICS
98354
Valve - EGR
S1625000004 REV.A
On Board Diagnosis (OBD) Monitor Readiness Information
S2418000009
Malfunction Indicator Lamp (MIL) Illumination. One Or More Exhaust Temperature Sensor (EGT) Diagnostic Trouble Codes (DTCs), Set.
98171
MODULE - ENGINE CONTROLLER
9100338REV1
GENERATOR Engine Prior to alternator/generator removal: 1. Inspect & check all electrical connections to the alternator a. 2-way connector containing field control circuit & alternator sense voltage circuit. b. Unplug & plug-in the 2-way connector for field & sense circuit. Verify the connection is tight & check for any bent pins in alternator connector or damage to female terminals in connector. c. Check Alternator B+ Stud connection to be sure nut is securing positive cable terminal properly (i.e. nut is clamping terminal & connection is tight). d. Check fuse between the alternator B+ stud & PDC terminal to make sure it is not blown. e. Be sure to follow service manual sections on ALTERNATOR CONTROL CIRCUIT DIAGNOSTIC & ALTERNATOR SENSE CIRCUIT DIAGNOSTIC looking for any opens & shorts (to ground or battery voltage). 2. Check/verify all grounds in the charging system circuit a. Check tightness of mounting bolts securing alternator to engine block. Alternator is a case ground component. b. Check main ground from engine to chassis; connection must be tight. c. Check battery ground cable connections are tight. d. Potentially, loosen alternator mounting bolts, without removing alternator, and re-tighten to torque specifications in service manual. e. After all steps above are complete, re-start engine & check charging system operation. 3. Verify that the Smart Charging System is not the reason for alternator low voltage & current output (Amps). a. Alternator charging can be suspended during engine idle operation because of the Smart Charge strategy. b. Refer to service manual section "System Operation - Smart Charging System". c. Refer to Star Case S2008000031 Rev A for low charging voltage & Smart Charge Mode Voltage Range diagram & mode descriptions. d. The alternator has no internal regulator; thus, has no smart circuitry. All alternator control signals come from ECM. 4. If alternator is faulty, remove alternator & mounting bolts. Return alternator with bolts for analysis at QEC.
S1908000050 REV.A
Checking Radio Software Level On A VP2 Radio
S2403000001
Rear Axle Differential Fluid Level Appears Low
98105
DAMPER - STRUT
97960
MODULE - STEERING CONTROL
S238A000026 REV.A
Intermittent Black Screen With Or Without Audio, Radio Resets Or Radio Locks Up At Times
S2408000015 REV.B
Remote Keyless Entry (RKE) Button Functions Does Not Work, Intermittent Vehicle Response When Using the RKE, Key Not Programmed
9100301
UCONNECT 5 W 8.4" DISPLAY Prior to replacing the radio, please check for any related recalls, TSBs, or any STAR Online publications. Please verify the radio is at the latest available software level. If active DTCs are set, perform the appropriate diagnostic procedure in service information. If the condition is intermittent, refer to Section 29 Non-DTC Based Diagnostics and perform the diagnostic procedure related to the customer's complaint. If concern is still present or the customer has returned to the dealer multiple times for the same complaint, contact engineering FCA Redacted Content. If no answer or call back within 15 minutes, continue with regular diagnosis.
S2408000008
Rain Sensing Auto Wipers Or Auto Headlamps Inoperative, DTC B221D-00, B23AA-00
0802324
Battery No Start, Jump Start, Tow-In Complaints Customer may experience one or more of the following: ? No start, jump start, or tow-in. ? Engine Stop Start (ESS) is inoperable.
0800624A
Navigation (NAV) Reboot When MOTA Fails The customer may describe one of more of the following: ? Radio navigation continues to reboot after a Map Update (MOTA). ? Navigation regularly cuts out and back on again. ? Radio switches to navigation without customer's input. This bulletin involves updating the Navigation maps via USB.
S1408000384
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
2100224
Flash: Transmission Control Module (TCM) Updates Customers may experience one or more of the following: ? "Service Transmission" message in the Instrument Cluster panel (IPC). ? Erratic shift bump felt/heard. ? Transmission stuck in seventh gear. ? Inability to accelerate. ? Not enough power to tow. This bulletin involves reprogramming the TCM with the latest available software.
2300324
Instrument Panel Delamination The customer may experience the following: ? Visible bubbling/delamination on the instrument panel base panel (cover). Inspect for visible bubbling/delamination on the instrument panel base panel. If bubbling/delamination is present, replace the base panel.
0819023
Radio Over the air update to R255.45.06 Customers may experience one or more of the following: No sound heard when Assist & SOS Call is established. Balance/Fade does not stay on when setup by one press. Wireless Phone interface freezes after User accepts incoming call when in a conference call. System switches to Wireless after key cycle, profile change, theme change, or theme mode change. After overnight sleep cycle defrost vent and dash vent are cut off due to duplicate front defrost. Surround sound image loads incorrectly when activating with Android Auto?. Radio plays different SXM® station than user selected. After a software update, previously added widgets to Shortcuts show up as "Couldn't add widget". SXM® presets grayed out, non-functional and audio intermittently fades in and out. Switch between the Cargo Camera screen and the AUX camera screen while switching between Night/Day modes, camera image may not be displayed. (Rearview camera functions normally). Deleting songs from Artist & Song Notifications, then Sports announcement displayed and "X" to cancel freezes screen. (Rearview camera functions normally). After a long sleep cycle, the left menu bar showing SXM® station categories (i.e. For You, Music, Sports, News, Presets) does not display all categories. When playing SXM®, after switching to a profile with a different Theme Mode, starting Bus Sleep cycle causes Presets Shown to change from 20 to 15. (Rearview camera functions normally). When call received from another vehicle, the voice of the receiving end is echoed back, the caller's vehicle has no echo issue. No response from Browse hard button when SXM® source is selected. Screen graphics/Theme - Shortcut widgets show up as "Loading", even after full sleep cycle. Android Auto? - Call duration displayed on status bar notification area is different than the actual duration. Widget view and Android Auto? screen are showing correct. Back Camera Icon is grayed out and it's not accessible f
S238A000058
Radio Navigation Displays Message ?No Maps Available?
S238A000056
Intermittent Black Screen With Or Without Audio, Radio Resets Or Radio Locks Up At Times
0824423
Radio R255.45.06 USB Software Update The customer may experience one or more of the following: No sound heard when Assist & SOS Call is established. Balance/Fade does not stay on when setup by one press. Wireless Phone interface freezes after User accepts incoming call when in a conference call. System switches to Wireless after key cycle, profile change, theme change, or theme mode change. After overnight sleep cycle defrost vent and dash vent are cut off due to duplicate front defrost. Surround sound image loads incorrectly when activating with Android Auto?. Radio plays different SXM? station than user selected. After a software update, previously added widgets to Shortcuts show up as "Couldnt add widget". SXM? presets greyed out, non-functional and audio intermittently fades in and out. Switch between the Cargo Camera screen and the AUX camera screen while switching between Night/Day modes, camera image may not be displayed (Rearview camera functions normally). Deleting songs from Artist & Song Notifications, then Sports announcement displayed and 9X9 to cancel freezes screen (Rearview camera functions normally). After a long sleep cycle, the left menu bar showing SXM? station categories (i.e. For You, Music, Sports, News, Presets) does not display all categories. When playing SXM?, after switching to a profile with a different Theme Mode, starting Bus Sleep cycle causes Presets Shown to change from 20 to 15 (Rearview camera functions normally). When call received from another vehicle, the voice of the receiving end is echoed back, the callers vehicle has no echo issue. No response from Browse hard key when SXM? source is selected. Screen graphics/Theme - Shortcut widgets show up as "Loading", even after full sleep cycle. Android Auto? - Call duration displayed on status bar notification area is different than the actual duration. Widget view and Android Auto? screen are showing correct. Back Camera Icon is grayed out and its not accessible from
94684
Transportation Bulletin T-23-01 Dealer Cleaning Program - 2023 - 2024 RAM Trucks - DJ, D2, DF, DD, DP, DS Models (Mexico RAM Built Trucks Only)
94691
FCA Caribbean Transportation Bulletin IT-23-01 Dealer Cleaning Program - 2023 - 2024 RAM Trucks - DJ, D2, DF, DD, DP, DS Models (Mexico RAM Built Trucks Only)
S238A000055
Audio Muted During A CarPlay Or Android Auto Phone Call
9100264
PSU Oil Pump Assy
9100266
brake hydroboost When replacing the Hydrobooster Assembly for a warrantable concern, please save the removed unit and call FCA REDACTED CONTENT for a FasTrack part return. ~ If no response in 15 minutes, proceed with repair. Please leave the last 8 of VIN, plus vehicle mileage, and dealer code.
S2318000012
Malfunction Indicator Lamp (MIL) Illumination. Diagnostic Trouble Code (DTC) P2580 ? Turbocharger Speed Sensor Circuit Low, Set.
S238A000026
Intermittent Black Screen With Or Without Audio, Radio Resets Or Radio Locks Up At Times
S238A000049
SXM Lockup (rearview camera function is not affected), Cannot Change Channel or Adjust Volume
94134
Warranty Bulletin D-22-07 Part Order Restriction Program ? Engine Control Module (ECM) ? Select 2022 - 2024 Ram 2500 Pickup (DJ), 2022 - 2024 Ram 3500 Pickup (D2), 2022 - 2024 Ram 3500 Cab Chassis (DD) and 2022 - 2024 4500/5500 Ram Cab Chassis (DP) (Rev. C)
94142
FCA Caribbean Warranty Bulletin ID-22-10 Part Order Restriction Program ? Engine Control Module (ECM) ? Select 2022 - 2024 Ram 2500 Pickup (DJ), 2022 - 2024 Ram 3500 Pickup (D2), 2022 - 2024 Ram 3500 Cab Chassis (DD) and 2022 - 2024 4500/5500 Ram Cab Chassis (DP) (Rev. C)
S238A000047
Humming Noise Through Speakers While Vehicle Is Off
S238A000046
Maps Over The Air (MOTA) Is Causing The Navigation App To Continuously Reboot Or Map loading Screen Shown
9100229
LIFTER, Hydraulic Roller Deactivating Please do not replace MDS lifters because the disconnecting pin is not lined up, this is normal and not a defect.
S2323000075
2nd Row Center Seat Lazy Or Slow When Folding.
9100226
Connector kit Before ordering this connector repair kit 68018957A$, check it in the Mopar Connector Repair Kit Website to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.
S238A000014
Radio Shutting Off Due to Hot Display
S2208000011
Wireless Qi Charger Not Charging
0821523
Radio Internal Amplifier Calibration The customer may experience the following: ? Hissing/water sprinkler/salt shaker noise coming from front/rear speakers. Heard when radio is on and no media is playing, or volume high/low with media playing. This bulletin involves performing a routine in the radio to reduce unwanted speaker noise.
0820923
Radio Over The Air Update from S24.6, S26.15 and T25.43 to T25.48 Software Version Customer may experience one or more of the following: ? Ambient Light Setting inoperable. ? Radio reset (Rearview camera functions normally). ? Voice Recognition (VR) inoperable. ? Audio sources inoperable. ? Wireless CarPlayT inoperable. ? Setting preferences not saved on correct profile. ? Audio loss. This bulletin provides information regarding the latest Firmware Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. The radio software will be updated from S24.6, S26.15 and T25.43 to T25.48. NOTE: The National campaign for this FOTA update is estimated to be launched on September 29, 2023.
93023
Warranty Bulletin D-16-03 - "Can / Am" Warranty Coverage - 594 / 595 / 596 WCC (Rev. B)
93120
FCA Caribbean Warranty Bulletin ID-23-20 "Can / Am" Warranty Coverage - 594 / 595 / 596 WCC
2400623
A/C Diagnostic LOP Change
S238A000043
SiriusXM (SXM) Advertisements Pop Up On Radio
9100202
PUMP ASSY AND REACTION SHAFT 2023 DJ & D2: If DTCs P0944 and P0868 are present, do not replace the torque converter or internal transmission components. Refer to SOL Publication S2321000007.
S2321000007
Malfunction Indicator Lamp (MIL) Illumination. Diagnostic Trouble Codes (DTCs) P0944 ? Loss of Hydraulic Pump Prime, and P0868 ? Transmission Fluid Pressure Low, Set.
0814823
Wi-Fi Hotspot Unavailable Customers may experience the following: ? Wi-Fi Hotspot does not work. This bulletin involves performing a proxi/proxy alignment.
S1808000097
Back-Up Camera Inoperative Complaints, Radio Display Blue or Blank When Placed in Reverse
S238A000037
Radio Resets Intermittently After A Screech Or Buzz Sound
0818623
Wi-Fi Hotspot Unavailable Customers may experience the following: ? Wi-Fi Hotspot does not work. This bulletin involves performing a proxi/proxy alignment.
TSB0818623
WiFi Hotspot does not work.
9100196
Lubrication and Maintenance Fluids If MOPAR fluids and chemicals are not readily available, please review Service Library for specifications so a suitable alternative can be used
S2109000011
Squeak, Chirp, Or Tick Noise From The Serpentine Belt Area. Additional Diagnostics.
0813923
Telematics Box Module (TBM) Over The Air Software Update to 5.39.1 Customers may experience one or more of the following: ? Uconnect Box Message at startup. ? Uconnect Box Error or Requires Service Message. ? Connectivity: Diagnostic Trouble Codes (DTCs) for Electronic Control Modules (ECUs) won?t be shown to customer through the Vehicle Health alert (Mobile app or email). This bulletin provides information regarding the latest Firmware Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. The TBM software will be updated from **5.13 and** 5.25 to 5.39.1.
9004433
PUMP, Vacuum For DTC Code P258B - ELECTRONIC VACUUM PUMP PERFORMANCE. Due to brake vacuum pumps returned with trouble not found, please follow the proper diagnostics outline in the service library this also includes checking all electrical and vacuum hose connections prior to replacement of the vacuum pump. This will avoid unnecessary repair and potential charge back on the vacuum pump.
0817623
Flash: Body Control Module (BCM) Updates Customers may experience the following: ? Unable to turn the Electronic Stability Control (ESC) OFF. This feature is ON by default. This bulletin involves reprogramming the BCM module with the latest available software.
S238A000034
USB Hub In-Operable
S238A000035
Pop Or Static Noise From Radio As The Vehicle Is Being Started
0901323
6.7L New Oil Usage Information Incorrect oil used. This bulletin provides information regarding the correct oil grade to use on the 6.7L Cummins used in the 2023 to 2013 HD Trucks. The following information is intended to eliminate confusion.
0816223
Flash: Global Telematics Box Module (TBM) Update to 5.39.1 The customer may experience the one or more of the following: ? Uconnect Box Message at Startup. ? Uconnect Box Error Or Requires Service Message. ? Uconnect Mobile App trunk status showing as closed when trunk is open. ? Diagnostic Trouble Codes (DTCs) for Electronic Control Modules (ECUs) won?t be shown to customer through the Vehicle Health alert (Mobile App or email). The TBM software will be updated from 5.25 to 5.39.1.
1808223
Flash: Powertrain Control Module (PCM) Updates Customers may experience the following: ? Cruise control inoperative. This bulletin involves reprogramming the PCM with the latest available software.
S238A000030
Apple CarPlay Not Working Or Disconnecting After Updating To iOS 16.3.1 Or Above
0815523
Electronic Vehicle Information Center (EVIC) Switch Inoperative The customer may experience one or more of the following: ? Steering Wheel EVIC Switch used to Navigate Cluster Menu is Inoperative. ? No Illumination. ? No Response to button press. This bulletin involves performing a power reset to activate/awaken the EVIC buttons.
91887
Warranty Bulletin D-20-13 STAR Center Uconnect 5 (R1) Radio Pre-Authorization Program ? Select Radios (New and Exchange) ?2023 Jeep Grand Cherokee (WL), 2023 Wagoneer and Grand Wagoneer (WS), 2023 Ram 1500 Pickup (DT), 2023 Ram Heavy Duty Pickup (DD/DF/DJ/DP/D2), 2024 Jeep Wrangler (JL) and 2024 Jeep Gladiator (JT) (Rev. F)
91890
FCA Caribbean Warranty Bulletin ID-22-11 STAR Center Uconnect 5 (R1) Radio Pre-Authorization Program ? Select Radios (New and Exchange) ?2023 Jeep Grand Cherokee (WL), 2023 Wagoneer and Grand Wagoneer (WS), 2023 Ram 1500 Pickup (DT), 2023 Ram Heavy Duty Pickup (DD/DF/DJ/ DP/D2), 2024 Jeep Wrangler (JL) and 2024 Jeep Gladiator (JT) (Rev. B)
0300323
Clicking Noise While In 4wd Ratcheting, Click, or Clicking noise in 4WD while turning. This bulletin involves replacing the front driveshaft.
9100160
Power wndow switch passenger
Reference70A
Customer Satisfaction Notification 70A - Radio Date/Time Update
S2323000020
Power Side Steps Reverse, Stop In Motion, And/Or Do Not Deploy Or Stow
1807423
Flash: Powertrain Control Module (PCM) Updates Customers may experience one or more of the following: ? Longer crank time than normal. ? Transmission overheat conditions with a message displayed in cluster stating "Transmission oil temperature is too hot". This bulletin involves reprogramming the Engine Control Module/Powertrain Control Module (ECM/PCM) with the latest available software.
1807223
Engine Control Module (ECM) Capacitor Leak Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that the one or more of the following Diagnostic Trouble Codes (DTCs) have been set: ? P0642 - Sensor Reference Voltage 1 Circuit Low. ? P0652 - Sensor Reference Voltage 2 Low. ? P06D3 - Sensor Reference Voltage 5 Circuit Low. ? P0102 - Mass Air Flow Sensor A Circuit Low. ? P0750 - Shift Solenoid 1 Control Circuit - Open. ? P0755 - Shift Solenoid 2 Control Circuit - Open. ? P0706 - Transmission Range Sensor Rationality. ? P0765 - Shift Solenoid D. ? P0770 - Shift Solenoid E. ? P2761 - Torque Converter Clutch Pressure Control Solenoid Control Circuit-Open. In addition, the customer may experience the following: ? An engine no crank/start. This bulletin involves performing an extended idle test and possibly replacing the ECM.
0700723
Water Quality When Mixed With Engine Coolant
9100153A
B2768-49 Right Impact Pressure Sensor-Internal Failure, prior to replacement of any components please contact FCA Redacted Content for further assistance. If no response in 15 minutes, proceed with repair.
S2323000021
Clunk Noise From Front End Driving Between 15 And 35 MPH And When Decelerating. C0604- Active Air Dam Control Performance
9100142
Mirror
S2208000080
Ambient Air Temperature Missing, Malfunction Indicator Lamp (MIL) Lamp On, Diagnostic Trouble Code (DTC) P0070-15 Ambient Air Temperature Sensor Circuit-Circuit Short to Battery or Open, P0073 Ambient Air Temperature Sensor Circuit High
9100097
3.5 INCH - SPEAKER ASSY P2 Before ordering a speaker part for crackles or rattling noises make sure to take the following steps: 1. Check for electrical harness routing too close to speaker's rear moving parts, improper connection, and/or harness pinch or damage. 2. Ensure no loose components, including trim grilles, fasteners, surrounding IP parts, etc. were found when removing the speaker. 3. Try "bad" speaker at another IP location and see if noise follows speaker. Try a different "good" speaker at "bad speaker location" and see if noise still happens at "bad" location. If even with this verification and adjustments the speaker sounds bad, test the individual speaker with the audio files provided in the Service Library Homepage under "Reference Materials" prior to replacement
S2223000063
Ambient Temperature Sensor Servicing.
S2303000002
Ratchet Type Click, Clicking Noise Heard In Four Wheel Drive (4WD) While Turning.
1804823
wiTECH Small Leak Verification Test (SLVT) - P0456-EVAP SYSTEM SMALL LEAK
0808623
Flash: Instrument Panel Cluster (IPC) Updates Customers may comment on the following: ? When customer turn on the vehicle after deep sleep, wrong splash screen appears. This bulletin involves reprogramming the IPC with the latest available software.
S238A000018
Uconnect Box Error Message With Active Or Stored Diagnostic Trouble Codes (DTC) B22A9-96, B1570-93, B1E21-96
Newsletter
FCA CARIBBEAN WARRANTY OPERATIONS NEWSLETTER
9100158
Power Window 1 Gang Before Replacing the Switch, please verify the following: 1- Check the switch internal resistance to verify the values are within specification stated in the service procedures. 2- Swap the switch with the issue with the other side. This switch is used in both rear doors. If after the swap the issue is now present at the other door and the original door position no longer has the issue, replace the switch.
S2108000015
Uconnect Box Require Service Message
0804423
Radio Over The Air S24.13 and S24.18 Updating to S26.17 Software Version Customers may experience one or more of the following: ? **Blank screen (Rear view camera is not affected and will still function normally).** ? Battery drain. ? Radio resets (Rear view camera will still function normally). ? Wireless connectivity device disconnect. ? CarPlayT icon does not appear in device manager. ? Climate icon missing. ? Audio disruptions. ? SXMT inoperative. ? Audio muted. ? Passenger screen blank. ? Passenger screen apps missing. ? Missing profiles icon. ? Instrument Panel Cluster (IPC) displays incorrect audio source. ? Radio is slow to respond. ? Trailer tire pressure configurations deleted. ? Steering wheel controls skipping SXMT channels. ? Recent calls not displayed. ? Phone audio playing with ignition off. The following improvements are also included with this update: ? Apple CarPlayT and Android AutoT improvements. ? Voice Recognition (VR) command improvements. ? Uconnect phone improvements. ? FOTA improvements. ? Passenger screen camera app improvements. ? Icon size/layout improvements. This bulletin provides information regarding the latest Firmware Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. The radio software will be updated from S24.13 or S24.18 to S26.17. NOTE: The national launch for the FOTA is expected to begin November 25, 2022.
88937
Warranty Bulletin D-22-07 Part Order Restriction Program ? Engine Control Module (ECM) ? Select 2022 and 2023 Ram 2500 Pickup (DJ), 2022 and 2023 Ram 3500 Pickup (D2), 2022 and 2023 Ram 3500 Cab Chassis (DD) and 2022 and 2023 4500/5500 Ram Cab Chassis (DP) (Rev. B)
08-028-23
Radio Over The Air Updating to S26.17 Software Version Battery drain on vehicle after connecting wiTECH to vehicle. This bulletin provides information regarding the latest Firmware Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. The radio software will be updated from S26.15 to S26.17. NOTE: National launch for this FOTA update is expected to begin February 09, 2023.
S238A000003
Backup Camera Blue Screen After Flat Bed Install
S2318000001
Diagnostic Trouble Code (DTC) P1400 ? Aftermarket Calibration Detected/Warranty Coverage Confirmation Required, Setting Falsely.
S1623000028 Rev.
Outside Power Fold Rearview Mirror Noise Or Loose At Pivot. Mirror Contacts Door Window Glass In The Folded Position.
S238A000001
Dead Battery Appears To Be Caused By Radio, Excessive Current Draw
88509
Warranty Bulletin D-20-13 Subject: STAR Center Uconnect 5 (R1) Radio Pre-Authorization Program ? Select Radios (New and Exchange) ?2021 - 2023 Jeep Grand Cherokee (WL), 2022 - 2023 Wagoneer and Grand Wagoneer (WS), 2023 Ram 1500 Pickup (DT) and 2023 Ram Heavy Duty Pickup (DD/DF/DJ/ DP/D2) (Rev. E)
S2323000002
Washer Light On And Will Not Turn Off After Adding Washer Solvent.
S2324000002
Customer Indicates Heat Is Blowing Warm Not Hot.
S1625000003 Rev.
Malfunction Indicator Lamp (MIL) Illumination. NOx Sensor Diagnostic Trouble Codes (DTCs) Diagnosis Information.
S2214000005
Upgrading To A Larger Capacity Fuel Tanks
S2207000003
Suspected Internal Exhaust Gas Recirculation (EGR) Cooler Coolant Leak, Additional Diagnostics.
31-002-22
Aluminum Body Panel Corrosion Repair Aluminum corrosion or bubbling along the leading edge of hood, hinges or other exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: Digital imaging pre authorization is required for Smart Warranty Base dealers or Pre Approval is required from Regional Office depending on market. This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.
S228A000005 Rev.
Uconnect Box Error Message, With Active or Stored Cellular Antenna Open or Short Diagnostic Trouble Codes (DTCs)
S2208000071 Rev.
Weather App May Freeze, Lockup Or Has Error Loading
9100103
Engine Oil - 0W20,Fluid - ATF+4,Engine Oil - 10W30,Engine Oil - 5W20,Engine Oil - 5W30
9100104
SENSOR Intrusion Module
9100105
Seal, Sunroof
9004470
CONNECTOR Trailer Tow,WIRING Trailer Tow,CONNECTOR 7 Way,WIRING Rear Bumper If the connector or wiring is physically damaged, burned, melted or corroded, prior to replacing the part, please contact FCA Redacted Content If no response in 15 minutes, proceed with repair. Please send pictures of the failed part to FCA Redacted Content
3100122
Approved Use of Weld Through Primers This bulletin documents the FCA US LLC position regarding the use of weld through primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.
85507
Warranty Bulletin D-19-02 Fast Feedback Program - 6.7L Cummins Engine & Fuel Injection Pump - 2019 - 2023 HD Ram ? All Models (Rev. J)
85136
Warranty Bulletin D-22-07 Parts Order Restriction Program - Engine Control Module (ECM) - Select 2022 and 2023 Ram 2500 Pickup (DJ), 2022 and 2023 Ram 3500 Pickup (D2), 2022 and 2023 Ram 3500 Cab Chassis (DD) and 2022 and 2023 4500/5500 Ram Cab Chassis (DP) (Rev. A)
Complaint counts are reports filed with NHTSA, not failure rates. A common model collects more of them than a rare one that breaks more often.