Vehicle report
Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
15-308-23R
This Service Information Bulletin outlines a systematic procedure for diagnosing parasitic draw (dark/standby current) in vehicles experiencing battery drain when the ignition is off, leading to no-start conditions or frequent jump-starts.This is an revised version of the original bulletin.
15-304-22R
This Bulletin has been developed to outline the steps for gathering basic but essential information during diagnosis of Infotainment concerns. (This is an revised version of the original bulletin.)
Article Locator
Techtips newsletter locator index.
15-333-25R
This bulletin contains illustrations of exchange components and their manufacturer as well as a description of the proper exchange procedure. This is an revised version of the original bulletin
SubaruNet Annoucement (E
This announcement is requesting retailer staff to retain the EyeSight protective hood covers from Generation 4 EyeSight cameras.
01-167-08R
This bulletin contains additional information for recommended materials listed in the Service Manuals for individual models.
SubaruNet Announcement (R
This announcement provides information on the remanufactured CVT transmission program.
07-240-26R
This Service Information Bulletin was developed to provide interim guidance for vehicles exhibiting DTC B2A20.
03-97-26
This bulletin announces the service manual correction regarding clutch master cylinder reservoir service procedures.
05-97-26
This Bulletin provides the diagnostic procedures to be followed when addressing customer concerns of steering wheel/vehicle body vibration when driving at highway speeds when tire/wheel balance is suspected.
10-105-25R
This bulletin announces the new procedure and Warranty Fail Code for FirstTime air conditioning (A/C) performance concerns possibly resulting from an undetected A/C refrigerant leak.
15-219-18R
This bulletin contains information to help when attempting to complete the STARLINK Telematics subscription process, an Error Code 202 and / or 204 may occur preventing the process from completing successfully
SubaruNet Announcement (A
This announcement provides information on the use of aftermarket services or tools for programming immobilizer keys/fobs.
Subaru Tech Tips Special
This Subaru service and technical support line newsletter provides information on the next phase of TechShare.
15-300-22R
This Bulletin provides the diagnostic procedure for the STARLINK® Remote Engine Start (RES).
Subarunet Announcement (E
This announcement has been created to address difficulties with software updates on Subaru Select Monitors with DST-010 interface firmware has been updated.
05-84-21R
This bulletin announces availability of new front wheel hub assemblies incorporating bearing surfaces having increased resistance to imperfections resulting from shock loads.
18-226-25R
This Service Information Bulletin provides the Service Manual Correction to the diagnostic procedure for DTC B2A16 (Immobilizer Key Collation Diagnosis).
15-333-25
This bulletin contains illustrations of exchange components and their manufacturer as well as a description of the proper exchange procedure.
Subaru Tech Tips (Article
Subaru service article locator.
15-130-08R
This bulletin provides information on the load carrying capacity reduced label when a port-installed or retailer-installed accessory exeeds 1.5 percent of the GVWR or 100 pounds, which ever is lower.
07-233-25R
This Bulletin provides details on a new formal testing, charging, and tracking procedure for all 12-volt batteries in new vehicle inventory.
07-236-25
This Bulletin outlines a comprehensive update to the dark current/parasitic draw diagnosis & testing procedures.
07-235-25
In the interest of customer satisfaction Subaru of America, Inc. (SOA) is extending the New Car Limited Warranty coverage in the models listed. The extension will address instances of “phantom braking” or the EyeSight/RAB systems causing unnecessary stoppage/slowing of the vehicle.
07-233-25
This Bulletin provides details on a new formal testing, charging, and tracking procedure for all 12-volt batteries in new vehicle inventory wjhich must be tested and reported every 30 days.
15-266-20R
This Bulletin provides helpful procedures and best practices to utilize when customers present with concerns relating to the operation of their Gen 2/Gen 3 Telematics system equipped Subaru.
15-320-24R
This bulletin contains illustrations of exchange components and their manufacturer as well as a description of the proper exchange procedure.
SubaruNet Announcement
Subaru of America, Inc. will release an OTA to perform a software update to the DCM. This is a preventive OTA.
13-108-25
This bulletin provides information on paint codes for vehicles in the 2026 line up.
Subaru Service Technical
Subaru Service Technical Support Newsletter special edition.
SubaruNet Annoucement
This announcment provides information on the release of the latest software updates to the Subaru Midtronics DSS-5000 Battery Diagnostic tool.
15-251-19R
This Bulletin provides additional diagnostics to follow when addressing a Telematics-related DTC B2A16.
SubaruNet Announcement (S
This announcement is to bring attention to the OTA for In-vehicle service appointment scheduler and In-vehicle message center.
01-168-09R
The purpose of this bulletin is to provide replacement key and immobilizer information along with an overview of the Subaru Lock Information web-site.
02-192-24R
This Bulletin announces the diagnostic procedures to be followed when diagnosing engine oil leakage on FA and FB type engines.
09-131-25
This bulletin announces the diagnostic procedures and availability of reprograming files to rectify the following Diagnostic Trouble Codes (DTCs). The ELCM may accumulate condensation causing the inaccurate detection of P2404. P0420 may become falsely detected due to unstable combustion caused by a downshift. The new reprogramming files contains enhanced software allowing for condensation conditions and downshift rotational speeds be more accurately detected by the Engine Control Module (ECM).
14-31-25
This Bulletin announces availability of a User Guide and an informative video to supplement the recent releases to retailers of the SOA321152 and SOA321153 Terminal Test Kits.
09-51-08R
The purpose of this bulletin is to advise of SOA’s revised Catalytic Converter Recycling Program shipping procedure.
Subarunet Announcement
This announcement is in regard to special service tool shipment will be shipped directly to the Subar retailers during February.
RC5 Head Unit OTA
A head unit OTA will be available via cellular network for Mid and High Grade CP1.5 head units.
Subarunet Announcement (
This announcement provides dealers information on an effort to increase the completion rate for the WRE-22 safety recall.
07-59-07R
This bulletin is for information purposes only.The bulletin adresses design changes of the headlamps and rear combination lamps, where moisture and or condensation may develop on the inside of the lamp lenses.
15-298-22R
This Service Information Bulletin announces the preferred practices to be used when handling vehicles equipped with Gen2 Telematics which are enrolled in the Subaru STARLINK® Security Plus Service featuring Stolen Vehicle Recovery Plus with Immobilizer.
02-192-24
This Service Information Bulletin announces the diagnostic procedures to be followed when diagnosing engine oil leakage on FA and FB type engines.
07-178-21R
This Service Information bulletin is being released as guidance for proper testing and charging of vehicle batteries.
15-320-24
This bulletin contains illustrations of exchange components and their manufacturer as well as a description of the proper exchange procedure.
02-191-22R
This bulletin announces availability of the NEW genuine Subaru engine oil filter.
03-94-24
This bulletin outlines the judgment criteria to be used when inspecting front transverse link bushings to reduce unnecessary bushing replacement.
Thermo Control Valve Vide
This thermo control valve video contains information on the replacement of thermo control valve.
13-107-24
This Bulletin provides SOA paint codes to help eliminate possible confusion for 2025 MY vehicles.
05-91-24
This Bulletin provides guidance for diagnosing a leaking front or rear suspension strut.
06-90-24
This bulletin provides diagnosis and procedure information to be applied when diagnosing potential fluid leaks on front and rear brake calipers. This information has been developed to reduce unnecessary brake caliper replacement.
WRE-22R
Subaru of America, Inc. (Subaru) is initiating a new safety recall for certain 2015-2021 model year WRX STI vehicles, which may contain a defective back-up lamp switch.
SubaruNet Announ
Subaru of America, Inc. (Subaru) is initiating a new safety recall for certain 2015-2021 model year WRX STI vehicles, which may contain a defective backup lamp switch.
07-207-22R
In the interest of customer satisfaction, Subaru of America, Inc. is extending the New Car Basic Warranty coverage for the 12 Volt batteries used in the above listed models and model years beyond the original three (3) years or thirty six thousand miles (36,000), whichever comes first.
15-285-21R
This Bulletin provides reference tables and photos to use for determining the infotainment head unit supplier and generation.
12-249-23R
This bulletin announces the recommended cleaning procedures to followed when encountering vehicles with long time exposure to pollen on painted surfaces on vehicles imported from Japan. This bulletin does not apply to SIA built vehicles.
WRE-22
Subaru of America, Inc. (Subaru) is initiating a new safety recall for certain 2015-2021 model year WRX STI vehicles, which may contain a defective back-up lamp switch.
15-302-22
This bulletin contains illustrations of exchange components and their manufacturer as well as a description of the proper exchange procedure.
Subaru Tech Tips
Special Edition, 2012 current model subaru evaporative diagnostics and smoke testing.
12-203-16R
This bulletin provides a procedure to address customer concerns of a squeaking sound originating from where the front seat belt buckle assembly attaches to the seat frame.
18-220-22
The purpose of this bulletin is to provide a description of current changes to Service Manuals available via the Subaru Technical Information System (STIS) web site.
15-192-22R
This bulletin has been developed to outline the steps for gathering basic essential information during diagnosis and repair of the Infotainment concerns. (Applicable to all models with Harman or Denso CP1 Infotainment).
05-79-20R
This bulletin announces a change made to the wheel lug nuts.
15-208-17R
This bulletin announces availability of an enhancement to the Gracenote database included in the vehicles listed equipped with F10 7â Navigation and 7â Display Audio head units.
18-212-21
The purpose of this bulletin is to provide a description of current changes to Service Manuals available via the Subaru Technical Information System (STIS) web site.
15-177-14R
This bulletin provides information to help diagnose and address different conditions relating to customer concerns which may arise when operating the new-generation âGen 2â and âGen 2.1â F10 Navigation and Display Audio systems.
18-210-21
Description of current changes to Service Manuals available via the Subaru Technical Information System (STIS) web site.
05-84-21
This bulletin announces availability of new front wheel hub assemblies incorporating bearing surfaces having increased resistance to imperfections resulting from shock loads.
11-201-21
This bulletin announces availability of reprogramming files to optimize the Engine Control Module (ECM). The new files will address DTC P0116 and hard starting in cold temperature concerns when an accessory engine block heater is utilized.
12-222-17R
This bulletin announces availability of a redesigned stay (reinforcement) to address isolated customer concerns of a creaking-type sound from the r/rear seat cushion / backrest hinge area.
14-22-16R
To help reduce confusion and increase technician efficiency, Subaru of America, Inc. (SOA) has developed the following cross reference list to help locate the appropriate Special Service Tool.
05-79-20
This Service Information Bulletin announces a change made to the wheel lug nuts.
12-305-20
This bulletin announces a design change made to the front hood air intake duct.
4-26-20
This bulletin describes a design change to the replacement hydraulic-type steering gearbox assembly.
10-19-20
The purpose of this bulletin is to provide a description of current changes to Service Manuals available via the Subaru Technical Information System (STIS) web site.
12-301-20
This bulletin outlines changes made to the rear shelf trim to address customer concerns of a rattling sound heard while driving over bumpy / rough roads.
18-201-20
The purpose of this bulletin is to provide a desription of current changes to service manuals available via the Subaru Technical Information System (STIS) web site.
18-200-20
This bulletin provides a description of current changes to Service Manuals.
06-76-20
This service Information bulletin provides precautions to follow when servicing the Brembo brake calipers utilized on the models listed. Because of their aluminum construction, it is critcal to take extra care when servicing.
01-181-20
All Models (Vehicle Cleaning- COVID-19Best Practices)
17-17-13R
This bulletin provides information regarding Event Data Recorder (EDR) functionality which has been incorporated into the airbag system.
18-199-20
The purpose of this bulletin is to provide a description of current changes to Service Manuals available via the Subaru Technical Information System (STIS) web site.
07-152-19R
This bulletin announces availability of new power window switch assemblies.
15-190-15R
This bulletin contains illustrations of exchange components and their manufacturer as well as a description of the proper exchange procedure. The exchange program policy can also be found in Sections 8.4.9 and 11.2.10 of your Claims Policies and Procedures Manual found in subarunet.
10-96-19
This bulletin announces availability of a new HVAC blower motor unit assemblies developed to address isolated concerns of the blower motor becoming inoperative. If this issues occurs on models with Auto A/C, the blower fan may become totally inoperative. If this issue occurs on models with Manual A/C, the blower fan may operate on high speed only. The root cause of these conditions is water intrusion into the blower motor causing rust and corrosion to develop. Over time, the blower motor may begin to draw more electrical current to operate. if that occurs, the additional draw can cause the related fuse and/ or blower resistor to fail. To address this condition, additional packing has been added to improve sealing of the blower unit case along with development of a new style cabin air filter which also in corporates improved sealing.
06-65-18R
This bulletin announces a new Vehicle Dynamics Control (VDC) Module and Hydraulic Control Unit (VDCCM&HCU). The new part was designed to address a small number of customer concerns regarding a clicking or ticking-type sound heard coming from the driverâs side footrest area. The new modules incorporate logic with enhanced internal solenoid and motor control characteristics.
12-264-19
This Service Information bulletin announces a design change made to the retaining bolt used to secure the child anchors to the rear shelf plates on the models listed above. This change was made in support of parts communization with other similar mounting bolts. There is no change between the old and new bolt in terms of function or durability.
07-152-19
This bulletin announces availability of new power window switch assemblies developed to address the following customer concerns: ? Power windows inoperative from the driver?s door master and / or passenger front door switch ? Unable to remotely operate other door windows from the driver?s door master switch ? One-Touch Auto Up / Down features inoperative from either / both front door switches
02-181-19
In the interest of customer satisfaction, Subaru of America, Inc. (SOA) is extending the New Car Limited Powertrain Warranty coverage for the turbocharged 2.5L ?EJ? short block assembly used in the above listed models and model years from the original five (5) years or sixty thousand (60,000) miles (whichever comes first) to eight (8) years or one-hundred thousand (100,000) miles (whichever comes first). This change is in response to an identified condition that can lead to isolated crankshaft bearing (main and / or connecting rod bearing) failures.
02-178-18R
This Service Information bulletin announces a design change made to the rubber timing hole access plug to improve its retention and prevent water intrusion into the converter case.
02-179-18
This Service Information Bulletin announces a change to the procedure and sequence used for torqueing the cylinder head bolts on the EJ25 turbocharged engine used in the 2015-2018MY STI.
12-251-18
This bulletin provides a service procedure to address a gap between the top edge of the door and the instrument panel on the models listed as shown in the photo below. The gap may also make the glove box door difficult to close fully.There is a latch to keep the glove box closed on both sides of the glove box door. If the door is closed without using enough force to engage both latches or by pushing it shut on just one side instead of in the middle, one may close and not the other. Over time, if the door is not fully closed with both latches, high cabin temperatures along with weight of the items inside the glove box may cause the assembly to deform slightly and a gap to develop.
10-86-17R
A design change was made to the blower motor assembly to address the following customer concerns: ? Blower fan is either inoperative or only operates on high speed. ? Excessive rotational-type sound heard when the fan is operating.
06-65-18
This bulletin announces a new Vehicle Dynamics Control (VDC) Module and Hydraulic Control Unit (VDCCM&HCU). The new part was designed to address a small number of customer concerns regarding a clicking or ticking-type sound heard coming from the driver?s side footrest area. The new modules incorporate logic with enhanced internal solenoid and motor control characteristics.
02-178-18
This Service Information bulletin announces a design change made to the rubber timing hole access plug to improve its retention and prevent water intrusion into the converter case.
18-195-18
The purpose of this bulletin is to provide a description of current changes to Service Manuals available via the Subaru Technical Information System (STIS) web site. The tables contained within this bulletin are to be used as guides for becoming aware of the latest changes. We advise you to always refer to the STIS web site when looking for the latest Service information.
07-139-18R
This bulletin outlines a design change made to the inner lens extension portion of the LED headlamp assembly. Under the right conditions, the shape of the lens for the actual head lamp light source can cause sunlight to be focused onto the extension portion of the lens resulting in deformation. A heatresistant shade has been added to protect the affected area.
12-234-18
This bulletin provides a repair procedure for replacing the foam cushion installed between the top front edge of the IP and the windshield glass. Use the supplied Service Procedure to address a customer concern involving the foam cushion becoming visible above the IP near the defroster vent outlets.
06-63-18R
This bulletin announces a design change to the EPB adapter cord harness connector. In some cases, the retaining tab of the connector may become damaged as a result of removal or installation for diagnosis and later and cause DTC C1956 or C1957 to set and the brake warning lamp to illuminate. The retaining tab portion of the connector has been changed to improve its durability and prevent recurrence of the DTC. If there is no prior history of disconnection and the connector lock tab is not damaged, check for another possible cause for these DTCs.
12-201-16R
IMPORTANT: This Service Bulletin has been as been replaced by TSB 12-243-18 dated 6/6/2018 entitled ?Paint Chipping between Hood Grille (Scoop) and Hood?. Please refer to this new bulletin for the latest information regarding this condition.
12-243-18
This bulletin replaces TSB 12-201-16R and provides a new repair procedure to address customer concerns of the hood scoop scrubbing the finish of the hood panel in the areas shown in the photo. Due to different expansion rates between the metal hood panel and the resin material used for the hood scoop, the edges of the scoop?s rear corners may come in contact with the hood panel and abrade the finish.
10-88-18
This bulletin announces a change made to the Automatic Climate Control Head Assembly. The change will address concerns where the temperature selected for cooling ?feels? warmer to the customer than the temperature displayed. The new programming will adjust the threshold for when cooling occurs to improve the air conditioning system?s cooling effect making it more closely match the customer?s selected temperature.
15-222-18
This bulletin announces a design change to the A/C Condenser receiver-dryer assembly. The change involves the addition of a rubber end cap and retaining clip onto the bottom of the receiver-dryer tank portion to prevent corrosion intrusion and enhance sealing.
12-238-18R
This bulletin announces a design change to the front door checkers used on the models listed. The new checker mechanism provides a more ?positive feel? of the detents or check positions as the front doors are opened and closed.
18-192-18
The purpose of this bulletin is to provide a description of current changes to Service Manuals available via the Subaru Technical Information System (STIS) web site. The tables contained within this bulletin are to be used as guides for becoming aware of the latest changes.
12-231-18R
This bulletin announces a design change to the air vent grille located in the lower portion of the trunk (or cargo) area. The shutters of the vent grille are designed to open briefly and relieve cabin pressure when the doors are shut with the windows fully closed. The vent grilles have rubber ?shutters? which occasionally, may catch on the frame (case) portion and not close properly allowing outside air / odor to enter the cabin.
02-172-18R
This bulletin provides details regarding a new oil filler tube o-ring developed to address engine oil seepage concerns. This seepage may accumulate along the bottom sealing surface of the rocker cover. The new o-ring utilizes material which has an increased resistance to engine heat.
F10-Gen2-NAV-15-
TECHNICAL SUPPORT GUIDE FOR NAVIGATION AND AUDIO F10 GEN2 SYSTEMS.
12-231-18
( 2017-2018MY Impreza - 5 Dr Only)
15-215-18
Models with FujitsuTEN (F10) Gen 2.0 / 2.1 Navigation or Display Audio Head Units ONLY. This bulletin provides a repair procedure to address specific, confirmed customer concerns of: ? Audio output interruption every 2-3 seconds when listening to AM or FM radio broadcasts ? No audio output at all when attempting to listen to a HD Radio broadcast.
02-164-16
This Service Information bulletin announces a design change to the internal contact portion of the oil pressure switch to increase durability
09-64-16
This Service Information bulletin announces a change to the shape of the rubber cap used on the flange nuts securing the sub-level sending unit to the fuel tank. In addition, two of the caps are now used in production instead of only one. This change was made to enhance productivity during vehicle assembly.
12-189-15R
This bulletin provides information about changes made to the rear shelf trim to address customer concerns of a rattling sound heard while driving over bumpy / rough roads. The sources of the rattle have been identified as: ? the mounting points for the center stop lamp where it fits into the package shelf ? the package shelf itself rattling against the inside of the rear glass ? the rib and/or stand portions located on the underside of the package shelf contacting the shelf portion of the vehicle body.
12-207-16
This bulletin announces a change to the procedure used in production of the rear door glass assembly. The bottom edge of the door glass is pressed into a metal channel lined with rubber. The channel attaches the door glass assembly to the window regulator. In below-freezing temperature conditions, water freezing in the channel combined with the door glass sticking to the door weatherstrip can increase chance of the glass separating from the channel when attempting to operate (lower) the window. A lubricant has been added to the rubber portion to insure the glass gets fully seated during assembly which maximizes the clamping force of the channel on the glass.
12-206-16
All Models Listed with Seat Lifter Feature. This bulletin provides a procedure to address a customer reported cosmetic condition of surface rust appearing on the inner seat cushion frame of the front seat assemblies.
07-111-16
This bulletin announces a design change to the headlamp assembly to improve sealing and prevent moisture intrusion. This condition may result from a slight misalignment of the attaching points during the headlamp assembly process. An improved sealing material is now being used for bonding the outer lens to the housing.
10-84-16R
This bulletin announces the availability of a new Air Conditioning compressor / clutch assembly to address customer concerns of the system not operating. Electrical windings located inside the clutch assembly have been changed to eliminate the condition. The service procedure will involve replacement of the A/C compressor and clutch as a complete assembly.
12-201-16
Paint Chipping between Hood Grille (Scoop) and Hood - This new bulletin replaces TSB 12-186-15 and announces a new repair procedure to address customer concerns of the hood scoop scrubbing the finish of the hood panel in the areas shown in the photo below. Due to different expansion rates between the metal hood panel and the resin material used for the hood scoop, the edges of the scoop?s rear corners may come in contact with the hood panel and abrade the finish.
15-200-16
Models with Fujitsu-TEN / FTEN / (F10) Gen2 Navigation System only. Fujitsu-TEN / FTEN / (F10) Navigation: Voice Recognition Concerns with Finding Addresses in Some Metro Areas.
18-186-16
The purpose of this bulletin is to provide a description of current changes to Service Manuals available via the Subaru Technical Information System (STIS) web site. The tables contained within this bulletin are to be used as guides for becoming aware of the latest changes.
15-177-14M2
When ordering exchange units from Fujitsu Ten through their online web site, some new information will soon be requested and in some cases required. To assist with that, a new Bluetooth Interview Form is available to facilitate the completion of an exchange order. The form is available on Subarunet at Service Operations & Technical >> Forms.
15-197-16
Although Fujitsu TEN (F10) Navigation units utilize an externally (faceplate) accessible MicroSD memory card, the MicroSD card used in Clarion display audio units is internal and not accessible. In the event a ?Check SD Memory Card? alert message appears on the faceplate display, an exchange display audio unit must be ordered through the applicable Clarion audio exchange procedure.
11-163-16
This bulletin announces availability of reprogramming files for optimization of the ECM. The files will address customer concerns of a lack of engine power output resulting from reduced turbocharger boost at high ambient temperatures while using 91 octane fuel.
12-182-15R
This bulletin announces availability of a new front door checker mechanism designed to hold the doors more securely when they are in partially open / closed positions. An additional detent position has also been added.
10-84-16
This bulletin announces the availability of a new Air Conditioning compressor / clutch assembly to address customer concerns of the system not operating. Electrical windings located inside the clutch assembly have been changed to eliminate the condition. The service procedure will involve replacement of the A/C compressor and clutch as a complete assembly.
05-61-16
This bulletin announces a design change to the front strut mounts intended to address customer concerns of a popping-type sound which may be heard when making low speed turns.
15-177-14M
When ordering exchange units from Fujitsu Ten through their online web site, some new information will soon be requested and in some cases required. Exchange order entry will now request a date and time when condition was last duplicated. The customer?s phone carrier, phone make and model will be required when Bluetooth or Connectivity failure sections are selected.
09-63-16
THIS SERVICE INFORMATION BULLETIN SERVES AS A REMINDER TO ALWAYS FOLLOW THE PROPER PROCEDURES WHEN DIAGNOSIS OF A DTC B1500 LEADS TO REPLACEMENT OF A FAULTY MAIN AND / OR SUB FUEL LEVEL SENSOR.
Tech tips
This is the final PDF for the 2016 January TechTIPS, please use and distribute as needed.
0710516
Change to Driver Controlled Center Differential (DCCD) Control Module
12-195-15
SHOULD YOU RECEIVE A CUSTOMER CONCERN OF VIBRATION OR LOOSENESS IN EITHER OF THE DOOR MIRRORS, A DESIGN CHANGE HAS BEEN MADE TO THE 3 MIRROR HEAD MOUNTING HOLES IN THE MOUNTING BASE. IN ADDITION, A NEW RETAINING BOLT AND TIGHTENING TORQUE SPECIFICATION ARE NOW USED TO SECURE THE MIRROR HEAD TO THE MOUNTING BASE. THIS BULLETIN PROVIDES A PROCEDURE FOR REPAIRING THE EXISTING MIRROR ASSEMBLY BY REPLACING THE THREE MOUNTING SCREWS WITH UPDATED FASTENERS. NOTE: REFER TO TSB 12-152-13 DATED 6/17/2013 FOR RELATED INFORMATION ON BRZ MODELS.
18-183-15
THE PURPOSE OF THIS BULLETIN IS TO PROVIDE A DESCRIPTION OF CURRENT CHANGES TO SERVICE MANUALS AVAILABLE VIA THE SUBARU TECHNICAL INFORMATION SYSTEM (STIS) WEB SITE. THE TABLES CONTAINED WITHIN THIS BULLETIN ARE TO BE USED AS GUIDES FOR BECOMING AWARE OF THE LATEST CHANGES. WE ADVISE YOU TO ALWAYS REFER TO THE STIS WEB SITE WHEN LOOKING FOR THE LATEST SERVICE INFORMATION. PRINTED PAGES WILL NOT BE MADE AVAILABLE TO UPDATE PRINTED SERVICE MANUALS. PAPER MANUALS MAY HAVE DIFFERENT PAGE NUMBERING THEN WHAT IS REFLECTED BELOW, BASED ON MULTIPLE NEW AND REVISED PAGES. PLEASE REFER TO THE INFORMATION CONTAINED ON THE STIS WEB SITE FOR ALL FUTURE, UPDATE SERVICE MANUAL INFORMATION.
12-190-15R
THIS BULLETIN PROVIDES A PROCEDURE TO ADDRESS CUSTOMER CONCERNS OF A CREAKING SOUND HEARD WHEN OPERATING THE CLUTCH PEDAL. THE CAUSE OF THE SOUND HAS BEEN IDENTIFIED AS A VERY SLIGHT AMOUNT OF MOVEMENT BETWEEN THE 2 LAYERS OF METAL (CIRCLED IN YELLOW) WHICH FORM THE SPECIFIC CLUTCH AND BRAKE PEDAL ASSEMBLY MOUNTING BRACKET SHOWN IN THE ILLUSTRATION AND PHOTOS BELOW.
07-99-15
ON SOME VEHICLES, A CUSTOMER MAY NOT BE ABLE TO ACCESS THE KEYLESS BUZZER VOLUME FUNCTION ON THE MULTI-FUNCTION DISPLAY (MFD). THIS BULLETIN ANNOUNCES AVAILABILITY OF REPROGRAMMING FILES FOR THE BODY INTEGRATED UNIT (BIU) TO FACILITATE SETTING THE VOLUME OF THE KEYLESS BUZZER VIA THE MFD.
Announcement
New Vehicle Receipt- Navigation SD Card Transit Storage Location Change
0116809R
Replacement Key and Immobilizer Info
171713R
Event Data Recorder (EDR) Function of Airbag Module
037314
This bulletin informs of a design change to the reverse idler gear and its internal spring along with a revised assembly procedure. The only purpose for the change was to enhance production efficiency.
Announcements-2
Effective with all 2015 model year cars and forward, the oil change interval is changing to 6,000 miles or 6 months, whichever comes first.
0214013
Oil Filler Cap Gasket Coming Unseated
WQE41-1
Puddle Light Recall
Complaint counts are reports filed with NHTSA, not failure rates. A common model collects more of them than a rare one that breaks more often.