Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
T-SB-0055-24 Rev2
Service Bulletin/Repair Instructions
Some 2005 – 2026 Toyota vehicles that have undergone water intrusion may exhibit a condition in which a musty odor is present. Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this Service Bulletin is to provide general guidelines and procedures for odor remediation. This Service Bulletin provides a guide on how to prepare and treat the interior of the vehicle for odor remediation. Refer to the applicable model and model year Repair Manual and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines.
T-SB-0035-24 Rev2
Service Bulletin/Repair Instructions
Acid rain results from rainwater or other airborne moisture that become acidic due to industrial chemical impurities in the atmosphere. If these acidic compounds settle on an exposed vehicle, especially the horizontal areas such as the hood, roof, and decklid, significant damage to the painted surfaces can occur. Acid rain damage can typically be identified on vehicles by the presence of stains on the paint surface that resemble hard water spots. Unlike water spots however, acid rain damage cannot be removed by regular washing procedures. Also, because acid rain can etch and soften the paint, normal buffing or polishing repair procedures should not be attempted. This can cause further damage and result in visible depressions in the paint surface. The following are the three major categories of acid rain damage: •Minor damage: requires only buffing to repair. •Moderate damage: usually requires neutralizing, color sanding, and buffing. •Severe damage: extending beyond 1/2 mil of clearcoat on a pearl, metallic, or solid color, requires neutralization, sanding, and repainting. In cases where acid rain damage is minor, neutralization and buffing with a liquid-type paint finessing product may provide an adequate repair. Only specially formulated products outlined in this bulletin should be used for that purpose. Unfortunately, other than minor damage, there is no simple method of determining the actual extent (depth) of acid penetration other than color sanding a representative affected area until there is no visible etching or depressions, followed by measuring the amount of paint removed with either a magnetic or digital-type film thickness gauge. The procedures in this bulletin are intended for use by qualified body/paint technicians and should not be attempted by inexperienced personnel. It is the dealer’s responsibility to protect and maintain the quality of the vehicle’s paint finish after receipt at the dealership prior to the first sale. Perform frequent vehicle washing, as often as daily, during high heat and humidity periods to minimize the potential for paint damage due to acid rain exposure. This is especially important in geographical areas known for high frequency and concentration of acid rain and industrial fallout.
T-SB-0038-24 Rev2
Service Bulletin/Repair Instructions
To prevent brake rotor rust from forming during transportation and storage, wheel film will be used instead of a cardboard type of anti-rust cover. The purpose of the wheel film is to shield the disc brake rotor from weather elements and initial rust before the vehicle is delivered to the customer. Consequently, the film should remain on the wheel for as long as possible.
T-SB-0039-24 Rev2
Service Bulletin/Repair Instructions
The condition known as acid rain is caused by airborne chemicals or particles in the atmosphere, which mix with rainwater, nighttime dew, or high humidity to form acidic compounds. If these contaminants settle and remain on a painted vehicle surface, especially the horizonal areas of the hood, roof, and decklid, significant damage can occur. This damage is the result of actual etching of the paint and appears as pitting or water spots. As acid rain droplets on the vehicle surface evaporate, the concentration strength of the acid increases, causing deeper and more rapid damage. This evaporation and corrosive action also occur more rapidly on dark colored cars as direct sun heat increases. It is the dealer’s responsibility to protect and maintain the quality of the vehicle’s paint finish after receipt at the dealership prior to the first sale. In areas known for high frequency and/or concentration of acid rain, frequent vehicle washing during high heat or humidity periods will minimize the potential for paint damage caused by acid rain. It is further recommended that either reverse osmosis or deionized water be used to prevent water spotting.
T-SB-0061-23 Rev2
Service Bulletin/Repair Instructions
Toyota vehicles are currently protected with RapgardTM protective film designed to protect the horizontal painted surfaces. This material protects from acid rain, environmental fallout, and rail contamination. Follow the Removal Procedure in this bulletin to remove the RapgardTM protective film within 90 days from initial application.
T-SB-0062-23 Rev2
Service Bulletin/Repair Instructions
Vehicles may occasionally be subjected to contamination by airborne iron particles shed from railroad tracks, train wheels, exposure to heavy machinery facilities, grinding, welding, etc. This type of contamination can be identified by the presence of small, red or brown particles on the paint surface. These particles are often difficult to see on dark color paints but can be easily felt when brushing a hand across horizontal body surfaces such as the hood, roof, or deck lid. Follow the Repair Procedure in this bulletin to clean vehicles that may have been subjected to contamination by airborne iron particles such as rail dust during rail transportation or extended storage near industrial areas.
T-SB-0055-24 Rev1
Service Bulletin/Repair Instructions
Some 2005 – 2024 Toyota vehicles that have undergone water intrusion may exhibit a condition in which a musty odor is present. Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this Service Bulletin is to provide general guidelines and procedures for odor remediation. This Service Bulletin provides a guide on how to prepare and treat the interior of the vehicle for odor remediation. Refer to the applicable model and model year Repair Manual and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines. This Service Bulletin is to provide a general overview and direction for the odor remediation process.
T-SB-0035-24 Rev1
Service Bulletin/Repair Instructions
Acid rain results from rainwater or other airborne moisture that become acidic due to industrial chemical impurities in the atmosphere. If these acidic compounds settle on an exposed vehicle, especially the horizontal areas such as the hood, roof, and decklid, significant damage to the painted surfaces can occur. Acid rain damage can typically be identified on vehicles by the presence of stains on the paint surface that resemble hard water spots. Unlike water spots however, acid rain damage cannot be removed by regular washing procedures. Also, because acid rain can etch and soften the paint, normal buffing or polishing repair procedures should not be attempted. This can cause further damage and result in visible depressions in the paint surface. The following are the three major categories of acid rain damage: •Minor damage: requires only buffing to repair. •Moderate damage: usually requires neutralizing, color sanding, and buffing. •Severe damage: extending beyond 1/2 mil of clearcoat on a pearl, metallic, or solid color, requires neutralization, sanding, and repainting. In cases where acid rain damage is minor, neutralization and buffing with a liquid-type paint finessing product may provide an adequate repair. Only specially formulated products outlined in this bulletin should be used for that purpose. Unfortunately, other than minor damage, there is no simple method of determining the actual extent (depth) of acid penetration other than color sanding a representative affected area until there is no visible etching or depressions, followed by measuring the amount of paint removed with either a magnetic or digital-type film thickness gauge. The procedures in this bulletin are intended for use by qualified body/paint technicians and should not be attempted by inexperienced personnel. It is the dealer’s responsibility to protect and maintain the quality of the vehicle’s paint finish after receipt at the dealership prior to the first sale. Perform frequent vehicle washing, as often as daily, during high heat and humidity periods to minimize the potential for paint damage due to acid rain exposure. This is especially important in geographical areas known for high frequency and concentration of acid rain and industrial fallout.
T-SB-0038-24 Rev1
Service Bulletin/Repair Instructions
To prevent brake rotor rust from forming during transportation and storage, wheel film will be used instead of a cardboard type of anti-rust cover. The purpose of the wheel film is to shield the disc brake rotor from weather elements and initial rust before the vehicle is delivered to the customer. Consequently, the film should remain on the wheel for as long as possible.
T-SB-0039-24 Rev1
Service Bulletin/Repair Instructions
The condition known as acid rain is caused by airborne chemicals or particles in the atmosphere, which mix with rainwater, nighttime dew, or high humidity to form acidic compounds. If these contaminants settle and remain on a painted vehicle surface, especially the horizonal areas of the hood, roof, and decklid, significant damage can occur. This damage is the result of actual etching of the paint and appears as pitting or water spots. As acid rain droplets on the vehicle surface evaporate, the concentration strength of the acid increases, causing deeper and more rapid damage. This evaporation and corrosive action also occur more rapidly on dark colored cars as direct sun heat increases. It is the dealer’s responsibility to protect and maintain the quality of the vehicle’s paint finish after receipt at the dealership prior to the first sale. In areas known for high frequency and/or concentration of acid rain (see Figure 1), frequent vehicle washing during high heat or humidity periods will minimize the potential for paint damage caused by acid rain. It is further recommended that either reverse osmosis or deionized water be used to prevent water spotting.
T-SB-0055-24
Service Bulletin/Repair Instructions
Some 2005 – 2024 Toyota vehicles that have undergone water intrusion may exhibit a condition in which a musty odor is present. Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this Service Bulletin is to provide general guidelines and procedures for odor remediation. This Service Bulletin provides a guide on how to prepare and treat the interior of the vehicle for odor remediation. Refer to the applicable model and model year Repair Manual and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines.
T-SB-0061-23 Rev1
Service Bulletin/Repair Instructions
Toyota vehicles are currently protected with RapgardTM protective film designed to protect the horizontal painted surfaces. This material protects from acid rain, environmental fallout, and rail contamination.
T-SB-0062-23 Rev1
Service Bulletin/Repair Instructions
Vehicles may occasionally be subjected to contamination by airborne iron particles shed from railroad tracks, train wheels, exposure to heavy machinery facilities, grinding, welding, etc. This type of contamination can be identified by the presence of small, red or brown particles on the paint surface. These particles are often difficult to see on dark color paints but can be easily felt when brushing a hand across horizontal body surfaces such as the hood, roof, or deck lid.
T-SB-0035-24
Service Bulletin/Repair Instructions
Acid rain results from rainwater or other airborne moisture that become acidic due to industrial chemical impurities in the atmosphere. If these acidic compounds settle on an exposed vehicle, especially the horizontal areas such as the hood, roof, and decklid, significant damage to the painted surfaces can occur. Acid rain damage can typically be identified on vehicles by the presence of stains on the paint surface that resemble hard water spots. Unlike water spots however, acid rain damage cannot be removed by regular washing procedures. Also, because acid rain can etch and soften the paint, normal buffing or polishing repair procedures should not be attempted. This can cause further damage and result in visible depressions in the paint surface. The following are the three major categories of acid rain damage: •Minor damage: requires only buffing to repair. •Moderate damage: usually requires neutralizing, color sanding, and buffing. •Severe damage: extending beyond 1/2 mil of clearcoat on a pearl, metallic, or solid color, requires neutralization, sanding, and repainting. In cases where acid rain damage is minor, neutralization and buffing with a liquid-type paint finessing product may provide an adequate repair. Only specially formulated products outlined in this bulletin should be used for that purpose. Unfortunately, other than minor damage, there is no simple method of determining the actual extent (depth) of acid penetration other than color sanding a representative affected area until there is no visible etching or depressions, followed by measuring the amount of paint removed with either a magnetic or digital-type film thickness gauge. The procedures in this bulletin are intended for use by qualified body/paint technicians and should not be attempted by inexperienced personnel. While the quality and durability of paint on Toyota vehicles is continuously being improved, it remains the dealer’s responsibility to protect and maintain the quality of the vehicle’s paint finish after receipt at the dealership prior to the first sale. To read, While the quality and durability of paint on Toyota vehicles is continuously being improved, it remains the dealer’s responsibility to protect and maintain the quality of the vehicle’s paint finish after receipt at the dealership prior to first sale. Perform frequent vehicle washing, as often as daily, during high heat and humidity periods to minimize the potential for paint damage due to acid rain exposure. This is especially important in geographical areas known for high frequency and concentration of acid rain and industrial fallout.
T-SB-0038-24
Service Bulletin/Repair Instructions
To prevent brake rotor rust from forming during transportation and storage, wheel film will be used instead of a cardboard type of anti-rust cover. The purpose of the wheel film is to shield the disc brake rotor from weather elements and initial rust before the vehicle is delivered to the customer. Consequently, the film should remain on the wheel for as long as possible. SUPERSESSION NOTICE The information contained in this bulletin supersedes Service Bulletin No. PD017-04. •The entire bulletin has been updated.
T-SB-0039-24
Service Bulletin/Repair Instructions
The condition known as acid rain is caused by airborne chemicals or particles in the atmosphere, which mix with rainwater, nighttime dew, or high humidity to form acidic compounds. If these contaminants settle and remain on a painted vehicle surface, especially the horizonal areas of the hood, roof, and decklid, significant damage can occur. This damage is the result of actual etching of the paint and appears as pitting or water spots. As acid rain droplets on the vehicle surface evaporate, the concentration strength of the acid increases, causing deeper and more rapid damage. This evaporation and corrosive action also occur more rapidly on dark colored cars as direct sun heat increases. While Toyota paint quality, durability, and resistance to environmental factors is continuously being improved, it remains the responsibility of the dealer to protect and maintain the vehicle’s paint finish from the time of arrival at the dealership until retail delivery to the customer. In areas known for high frequency and/or concentration of acid rain (see Figure 1), frequent vehicle washing during high heat or humidity periods will minimize the potential for paint damage caused by acid rain. It is further recommended that either reverse osmosis or deionized water be used to prevent water spotting.
T-PANT-2024-004-
Service Bulletin/Repair Instructions
This is to advise of various price adjustments that will affect Toyota Genuine Motor Oil and Long Life Coolant, effective March 1, 2024. These products are ordered through the Toyota Complete Maintenance Care (TCMC) website.
T-SB-0043-14
Service Bulletin/Repair Instructions
OBSOLETE NOTICE January 22, 2024: This bulletin is now obsolete. Please see T-SB-0057-18.
TSB003220
Service Bulletin/Repair Instructions
TSB: Replacement certification labels (the vinyl label installed on the driver door or door post) and VIN plates (the metal plate riveted to dashboard) (see Figure 1) for most 1979 ? 2023 model year vehicles may be available provided the requests meet the criteria listed in this Service Bulletin. Follow the Procurement Procedure in this bulletin to request a replacement certification label or VIN plate.
T-SB-0057-18
Service Bulletin/Repair Instructions
TSB: The Immobilizer and Smart Key Reset is a feature that allows the registration of new keys when all master keys are lost. Once the system is reset, all previously registered keys will be erased. Follow the procedures in this bulletin to reset a vehicle Immobilizer or Smart Key system.
T-SB-0094-21 Rev
Service Bulletin/Repair Instructions
TSB: Some 2005 ? 2022 model year Toyota vehicles that have undergone water intrusion may exhibit a condition in which a musty smell is present. Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this service bulletin is to provide general guidelines and procedures for odor remediation. This service bulletin provides a guide on how to prepare the interior of the vehicle prior to an odor remediation being performed, as well as contact information for an approved vendor who will arrange the remediation, and instructions on how to prepare the interior of the vehicle for reassembly once the remediation has been completed. Refer to all model and model year specific Repair Manuals and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines. This service bulletin is to provide a general overview and direction for the odor remediation process.
TSB009421Rev1
Service Bulletin/Repair Instructions
TSB: Some 2005 ? 2022 model year Toyota vehicles that have undergone water intrusion may exhibit a condition in which a musty smell is present. Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this service bulletin is to provide general guidelines and procedures for odor remediation. This service bulletin provides a guide on how to prepare the interior of the vehicle prior to an odor remediation being performed, as well as contact information for an approved vendor who will arrange the remediation, and instructions on how to prepare the interior of the vehicle for reassembly once the remediation has been completed. Refer to all model and model year specific Repair Manuals and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines. This service bulletin is to provide a general overview and direction for the odor remediation process
TTT063620
Service Bulletin/Repair Instructions
TT: Some Toyota vehicles installed with Toyota Complete Maintenance Care (TCMC) brake pads may exhibit a groan or squeak noise in various driving conditions
T-SB-0014-22
Service Bulletin/Repair Instructions
TSB: This Service Bulletin includes procedures to replace damaged or loose front carpet floor retainer(s) without replacing the carpet assembly. Follow the Repair Procedure in this bulletin to replace the loose or damaged carpet floor retainer(s).
T-SB-0094-21
Service Bulletin/Repair Instructions
TSB: Some 2005 ? 2022 model year Toyota vehicles that have undergone water intrusion may exhibit a condition in which a musty smell is present. Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this service bulletin is to provide general guidelines and procedures for odor remediation. This service bulletin provides a guide on how to prepare the interior of the vehicle prior to an odor remediation being performed, as well as contact information for an approved vendor who will arrange the remediation, and instructions on how to prepare the interior of the vehicle for reassembly once the remediation has been completed. Refer to all model and model year specific Repair Manuals and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines. This service bulletin is to provide a general overview and direction for the odor remediation process.
T-TT-0578-19 Rev
Service Bulletin/Repair Instructions
TT: Some customers may encounter Bluetooth® connectivity concerns such as: ?Difficulty to pair the phone. ?Intermittent Bluetooth® failure to connect to the vehicle when first turning on the vehicle. ?Various Bluetooth® Audio functions are no longer functioning with customer?s phone such as ability to change the track using the steering wheel controls. These concerns can be caused by changes made on the customer?s phone. Make sure to inquire with the customer if the connectivity concerns occurred after receiving an operating system update on their phone, or if they have restored their phone data/settings recently.
Toyota Safety Re
Service Bulletin/Repair Instructions
Toyota Safety Recall and Service Campaign - Technician Certification Requirements
T-TT-0636-20 Rev
Service Bulletin/Repair Instructions
TT: Some Toyota vehicles installed with Toyota Complete Maintenance Care (TCMC) brake pads may exhibit a groan or squeak noise in various driving conditions.
T-SB-0040-08 Obs
Service Bulletin/Repair Instructions
OBSOLETE NOTICE March 08, 2021: This bulletin is now obsolete. Please see T-SB-0044-16.
T-SB-0032-20 Rev
Service Bulletin/Repair Instructions
TSB: Replacement certification labels (the vinyl label installed on the driver door or door post) and VIN plates (the metal plate riveted to dashboard) (see Figure 1) for most 1979 ? 2021 model year vehicles may be available provided the requests meet the criteria listed in this Service Bulletin. Follow the Procurement Procedure in this bulletin to request a replacement certification label or VIN plate.
T-TT-0636-20
Service Bulletin/Repair Instructions
TT: Some Toyota vehicles installed with Toyota Complete Maintenance Care (TCMC) brake pads may exhibit a groan or squeak noise in various driving conditions.
T-SB-0063-20
Service Bulletin/Repair Instructions
TSB: SUPERSESSION NOTICE The information contained in this bulletin supersedes Service Bulletin Nos. ST005-01, SU001-08, and T-SB-0391-08. The aforementioned bulletins are obsolete, and any printed versions should be discarded. Be sure to review the entire content of this service bulletin before proceeding. This Service Bulletin provides best practice procedures for vehicle pulling complaint, diagnosis, and repair for 2002 ? 2021 model year Toyota vehicles. This information supplements Repair Manual procedures when the symptoms are: ?Vehicle Pulling: The vehicle moves to the right or left when the driver holds the steering wheel while driving straight ahead without exerting steering effort. ?Steering Wheel Off Center: The vehicle travels straight, but the steering wheel is not pointed straight ahead. The vehicle is not pulling. Before repairing a vehicle pulling to one side, it is necessary to clearly identify the cause of the pulling condition. Frequently, pulling to one side is diagnosed as a wheel alignment concern. However, the actual cause may be related to the lateral force generated by the tires, vehicle damage, road crown or worn components. Performing a wheel alignment when tire force is the cause could result in the wheel alignment being set at a value outside of specifications. This could then cause other problems such as uneven tire wear, etc. A customer may notice a pull to the left when in the left lanes of travel and notice a pull to the right or no pull when traveling in the right lanes of travel on the very same section of roadway. This road crown effect is environmental and cannot be corrected with suspension adjustments or any other wheel or tire modification discussed in this bulletin.
T-SB-0391-08 Obs
Service Bulletin/Repair Instructions
TSB: OBSOLETE NOTICE June 23, 2020: This bulletin is now obsolete. Please see T-SB-0063-20.
DOR-M3J3F-07
Service Bulletin/Repair Instructions
These SKUs are Exhaust Manifolds with Catalytic Converters. The customer communication requested return of unsold inventory due to a loss of CARB certification. These SKUs can no longer be sold as they do not meet CARB standards, but parts on vehicles are not effected.
DOR-M9J4S-07
Service Bulletin/Repair Instructions
These SKUs are Exhaust Manifolds with Catalytic Converters. The customer communication requested return of unsold inventory due to a loss of CARB certification. These SKUs can no longer be sold as they do not meet CARB standards, but parts on vehicles are not effected.
T-SB-0304-17 Obs
Service Bulletin/Repair Instructions
TSB: OBSOLETE NOTICE April 07, 2020: This bulletin is now obsolete. Please see T-SB-0032-20. Replacement Certification Labels and VIN Plates
T-SB-0032-20
Service Bulletin/Repair Instructions
TSB: SUPERSESSION NOTICE The information contained in this bulletin supersedes Service Bulletin Nos. PG021-88, PG015-89, PG0015-90, PG002-91, PG002-93, PG005-97, PG007-01, PG007-07, PG006-01, PG004-97, T-SB-0144-08, and T-SB-0304-17. The aforementioned bulletins are obsolete, and any printed versions should be discarded. Replacement certification labels (the vinyl label installed on the driver door or door post) and VIN plates (the metal plate riveted to dashboard) (see Figure 1) for most 1979 ? 2020 model year vehicles may be available provided the requests meet the criteria listed in this Service Bulletin. Follow the Procurement Procedure in this bulletin to request a replacement certification label or VIN plate.
T-SB-0142-13_Obs
Service Bulletin/Repair Instructions
OBSOLETE NOTICE February 12, 2020: This bulletin is now obsolete. Please see T-SB-0010-20.
T-SB-0008-20
Service Bulletin/Repair Instructions
TSB: Vehicles may display evidence of a fluid leak or fluid seep from powertrain components. This bulletin explains how to determine the differences between a fluid leak versus a fluid seep. Cases that are determined to be a ?leak? should be repaired accordingly and will be covered under warranty if applicable. Cases that are determined to be a ?seep? should be documented on the repair order and inspected at the next service interval. Follow the Repair Information in this bulletin to determine if the concern in question is a fluid leak or fluid seep and review the Repair Procedure section to address the condition. NOTE This bulletin applies to ALL powertrain fluids excluding fuel and coolant.
T-TT-0578-19
Service Bulletin/Repair Instructions
TT: Some customers may encounter Bluetooth® connectivity concerns such as: ? Difficulty to pair the phone. ? Intermittent Bluetooth® failure to connect to the vehicle when first turning on the vehicle. ? Various Bluetooth® Audio functions are no longer functioning with customer?s phone such as ability to change the track using the steering wheel controls. These concerns can be caused by changes made on the customer?s phone. Make sure to inquire with the customer if the connectivity concerns occurred after receiving an operating system update on their phone, or if they have restored their phone data/settings recently.
T-SB-0134-16-Rev
Service Bulletin/Repair Instructions
TSB: REVISION NOTICE July 01, 2019 Rev2: ? Applicability has been updated to 2019 ? 2020 model year Toyota vehicles. ? The Techstream Preparation and Process Overview sections have been updated. October 30, 2017 Rev1: ? Applicability has been updated to include 2018 model year vehicles. Any previous printed versions of this bulletin should be discarded. SUPERSESSION NOTICE The information contained in this bulletin supersedes SB No. T-SB-0012-13. Service Bulletin No. T-SB-0012-13 is obsolete and any printed versions should be discarded. Be sure to review the entire content of this bulletin before proceeding. Flash reprogramming allows the Electronic Control Unit (ECU) software to be updated without replacing the ECU. Flash calibration updates for specific vehicle models/ECUs are released as field-fix procedures described in individual Service Bulletins. This bulletin details the Techstream ECU flash reprogramming process and outlines use of the Technical Information System (TIS) and the Calibration Update Wizard (CUW). Flash calibration updates can only be applied to the vehicle/ECU combination for which they are intended. ECUs have internal security that will not allow them to be programmed with another ECU?s information. NOTE ECU is a Toyota term used to describe integrated computerized devices responsible for managing the operation of a system or subsystem. For the purposes of this bulletin, the term ?ECU? is used as a generic label for the following SAE J1930 standard references: ? Powertrain Control Module (PCM) ? Engine Control Module (ECM) ? Transmission Control Module (TCM) ? Any other Toyota specific control unit
T-TT-0414-16-Rev
Service Bulletin/Repair Instructions
TT: Some customers may encounter Bluetooth® connectivity concerns such as: ? Difficulty to pair the phone. ? Intermittent Bluetooth® failure to connect to the vehicle when first turning on the vehicle. ? Various Bluetooth® Audio functions are no longer functioning with customer?s phone such as ability to change the track using the steering wheel controls. These concerns can be caused by changes made on the customer?s phone. Make sure to inquire with the customer if the connectivity concerns occurred after receiving an operating system update on their phone, or if they have restored their phone data/settings recently.
PG004-97-Obsolet
Service Bulletin/Repair Instructions
Technical Service Bulletin: OBSOLETE NOTICE: July 31, 2018: This bulletin is now obsolete. Please see T-SB-0304-17.
PG006-01-Obsolet
Service Bulletin/Repair Instructions
Technical Service Bulletin: OBSOLETE NOTICE: July 31, 2018: This bulletin is now obsolete. Please see T-SB-0304-17.
T-SB-0304-17_Rev
Service Bulletin/Repair Instructions
TSB: REVISION NOTICE July 31, 2018 Rev2: ? The Supersession Notice has been updated. January 11, 2018 Rev1: ? The Supersession Notice has been updated. Any previous printed versions of this bulletin should be discarded. SUPERSESSION NOTICE The information contained in this bulletin supersedes Service Bulletin Nos. PG021-88, PG015-89, PG0015-90, PG002-91, PG002-93, PG005-97, PG007-01, PG007-07, PG006-01, PG004-97, and T-SB-0144-08. Service Bulletin Nos. PG021-88, PG015-89, PG0015-90, PG002-91, PG002-93, PG005-97, PG007-01, PG007-07, PG006-01, PG004-97, and T-SB-0144-08 are obsolete and any printed versions should be discarded. Vehicle replacement certification labels (the vinyl label installed on the driver door or door post) and VIN plates (the metal plate riveted to dashboard) may be available from Toyota, provided the request meets one of the criteria listed in this Service Bulletin. Replacement Certification Label and VIN Plate Criteria A replacement certification label and/or VIN plate may be requested if: ? The vehicle was in an accident and the label and/or plate is damaged or attached to a part that will be replaced during the repair. ? The label and/or plate was stolen.
ZG7_Toyota POL17
Service Bulletin/Repair Instructions
Warranty Policy Bulletin: Toyota has received reports of customer concerns where the vehicles rear hatch glass broke during defroster operation.
T-SB-0026-15_Rev
Service Bulletin/Repair Instructions
TSB: REVISION NOTICE June 8, 2018 Rev2: ? Applicability has been updated to exclude 2016 ? 2017 model year Tacoma vehicles. ? The Repair Procedure section has been updated. May 15, 2017 Rev1: ? Applicability has been updated to include 2016 ? 2017 model year Tacoma and 4Runner vehicles. ? The Introduction section has been updated. Any previous printed versions of this bulletin should be discarded. Some 2004 ? 2017 model year 4Runner vehicles, 2007 ? 2014 model year FJ Cruiser vehicles, and 2005 ? 2015 model year Tacoma vehicles equipped with part-time 4WD may exhibit a cyclical groaning or grinding noise coming from the front differential in 2WD that goes away when operated in 4WD. This noise can be addressed by replacing the needle bearing on the left side of the front differential. Refer to the Repair Procedure for needle bearing roller replacement instructions.
T-SB-0187-12_Rev
Service Bulletin/Repair Instructions
TSB: REVISION NOTICE February 12, 2018 Rev2: ? Applicability has been updated to include 2015 ? 2018 model year vehicles. January 23, 2014 Rev1: ? Applicability has been updated to include 2013 ? 2014 model year vehicles. Any previous printed versions of this bulletin should be discarded. Toyota vehicles are equipped with either conventional or run-flat tires. Sometimes punctures may occur as a result of contact with road debris or other hazards. If a puncture occurs, it may be possible to repair the tire and return it to service. With a conventional tire it is not possible to drive for an extended amount of time with the tire at low pressures as damage to the tire may occur. With run-flat tires, due to reinforced sidewalls, it is possible to drive for up to 100 miles at speeds less than 55 mph with little or no damage to the tire. The U.S. Tire Manufacturers Association (UTSMA) provides guidelines and recommendations for tire repair and replacement. It also provides information related to: ? Basic tire information ? Tire maintenance and safety ? Driver education, tire safety curriculum.
TSR-1212-17
Service Bulletin/Repair Instructions
Technician Certification Requirements.
T-SB-0229-12_Rev
Service Bulletin/Repair Instructions
TSB: REVISION NOTICE November 22, 2017 Rev1: ? Applicability has been updated to include 2014 ? 2018 model year vehicles. Any previous printed versions of this bulletin should be discarded. In the event that a Toyota vehicle becomes submerged in water, many components may be physically damaged. Electrical and electronic components, including wiring harnesses, are particularly susceptible to corrosion and subsequent malfunction. Although any flooding can be damaging, salt water flooding elevates the potential for abnormal conditions and may increase risks due to its highly corrosive and conductive nature. Salt residue also continues to corrode and remain conductive even after a vehicle dries. This bulletin is intended to assist with safe handling and inspection of flood damaged vehicles and to provide basic guidance on likely needed repairs.
T-SB-0144-08_Obs
Service Bulletin/Repair Instructions
TSB: OBSOLETE NOTICE November 21, 2017: This bulletin is now obsolete. Please see T-SB-0304-17.
T-SB-0134-16_Rev
Service Bulletin/Repair Instructions
TSB: REVISION NOTICE October 30, 2017 Rev1: * Applicability has been updated to include 2018 model year vehicles. SUPERSESSION NOTICE The information contained in this bulletin supersedes SB No. T-SB-0012-13. Flash reprogramming allows the Electronic Control Unit (ECU) software to be updated without replacing the ECU. Flash calibration updates for specific vehicle models/ECUs are released as field-fix procedures described in individual Service Bulletins. This bulletin details the Techstream ECU flash reprogramming process and outlines use of the Technical Information System (TIS) and the Calibration Update Wizard (CUW). Flash calibration updates can only be applied to the vehicle/ECU combination for which they are intended. ECUs have internal security that will not allow them to be programmed with another ECU's information.
T-SB-0304-17
Service Bulletin/Repair Instructions
TSB: Vehicle replacement certification labels (the vinyl label installed on the driver door or door post) and VIN plates (the metal plate riveted to dashboard) may be available from Toyota, provided the request meets one of the criteria listed in this Service Bulletin.
T-SB-0218-17_Rev
Service Bulletin/Repair Instructions
TSB: REVISION NOTICE July 20, 2017 Rev1: Applicability has been updated to exclude 2007 ? 2017 model year Avanza vehicles. Some hazardous material treatment and handling regulations at the state and local level define the pre-disposal deployment of airbag and pre-tensioner assemblies as hazardous material treatment. Hazardous material treatment may require special training, certification or licensing in certain areas. TMS recommends that dealership personnel carefully review and follow ALL local and state regulations, and where necessary, contract with Environmental Protection Agency (EPA) Licensed Hazardous Waste Transportation and Disposal facilities.
ZG7 Dealer Packa
Service Bulletin/Repair Instructions
Dealer Package: Toyota is announcing a Warranty Enhancement Program to extend the warranty coverage for Broken Rear Hatch Glass on Certain 2003-2009 Model Year 4Runner Vehicles.
ZG7_Dealer Email
Service Bulletin/Repair Instructions
Dealer Email: Toyota is announcing a Warranty Enhancement Program to extend the warranty coverage for Broken Rear Hatch Glass on Certain 2003-2009 Model Year 4Runner Vehicles.
ZG7_POL17-03_War
Service Bulletin/Repair Instructions
Warranty Policy Bulletin POL17-03: Toyota has received reports of customer concerns where the vehicles rear hatch glass broke during defroster operation.
ZG7_Region Email
Service Bulletin/Repair Instructions
Region Email: Toyota is announcing a Warranty Enhancement Program to extend the warranty coverage for Broken Rear Hatch Glass on Certain 2003-2009 Model Year 4Runner Vehicles.
T-SB-0189-17
Service Bulletin/Repair Instructions
TSB: Some 2003 ? 2009 model year 4Runner vehicles may exhibit back door glass "broken" without external impact. This condition may be associated with rear window defogger usage before glass breakage. Updated rear glass has been developed to address this condition.
TSB018217
Service Bulletin/Repair Instructions
TSB: SUPERSESSION NOTICE The information contained in this bulletin supersedes SB No. T-SB-0101-11. Applicability has been updated to include 2016 ? 2017 model year vehicles. Service Bulletin No. T-SB-0101-11 is Obsolete and any printed versions should be discarded. Be sure to review the entire content of this bulletin before proceeding. When servicing interior electrical switches and components, please note the precautions in this bulletin to avoid damaging electrical components and switches. Many lubricants, cleaners, and automotive chemicals contain silicone or other compounds that may contaminate electrical contacts, and therefore increase electrical resistance and decrease switch performance. The use of any cleaners or fluids may increase the risk of further damage to electrical components.
T-SB-0012-13 Rev
Service Bulletin/Repair Instructions
TSB: OBSOLETE NOTICE: September 14, 2016: This bulletin is now obsolete. Please see T-SB-0134-16.
T-SB-0142-13 Rev
Service Bulletin/Repair Instructions
TSB: REVISION NOTICE November 10, 2016 Rev2: ? Applicability has been updated to include 2016 ? 2017 model year Toyota vehicles. ? Parts Information section has been updated. Some 2004 ? 2017 model year Toyota vehicles may exhibit odors naturally occurring from the HVAC system and/or related environmental factors. Although there is no way to eliminate these odors, follow the General Procedure in this bulletin to minimize the odors experienced.
T-SB-0134-16
Service Bulletin/Repair Instructions
TSB: Supersession Notice. Flash reprogramming allows the ECU software to be updated without replacing the ECU. Flash calibration updates for specific vehicle models/ECUs are released as field-fix procedures described in individual Service Bulletins. This bulletin details the Techstream ECU flash reprogramming process and outlines use of the Technical Information System (TIS) and the Calibration Update Wizard (CUW). Flash calibration updates can only be applied to the vehicle/ECU combination for which they are intended. ECUs have internal security that will not allow them to be programmed with another ECU?s information.
BST-Dealer Packa
Service Bulletin/Repair Instructions
Dealer Package: In our continuing effort to ensure the best in customer satisfaction, Toyota has converted Limited Service Campaign (LSC) BST into Special Service Campaign (SSC) BST with no expiration date. Toyota will install Smart Stop Technology on the below listed model and model year vehicles. This feature will cut engine power in case of simultaneous application of both the accelerator and brake pedals at certain speeds and in certain driving conditions.
BST-Region Lette
Service Bulletin/Repair Instructions
Region Letter: In our continuing effort to ensure the best in customer satisfaction, Toyota has converted Limited Service Campaign (LSC) BST into Special Service Campaign (SSC) BST with no expiration date. Toyota will install Smart Stop Technology on the below listed model and model year vehicles. This feature will cut engine power in case of simultaneous application of both the accelerator and brake pedals at certain speeds and in certain driving conditions.
BST-TI-Smart Sto
Service Bulletin/Repair Instructions
Technical Instructions: In our continuing effort to ensure the best in customer satisfaction, Toyota has converted Limited Service Campaign (LSC) BST into Special Service Campaign (SSC) BST with no expiration date. Toyota will install Smart Stop Technology on the below listed model and model year vehicles. This feature will cut engine power in case of simultaneous application of both the accelerator and brake pedals at certain speeds and in certain driving conditions.
T-TT-0414-16
Service Bulletin/Repair Instructions
TT: Some customers may encounter Bluetooth® connectivity concerns such as: *Difficulty to pair the phone. *Intermittent Bluetooth® failure to connect to the vehicle when first turning on the vehicle. *Various Bluetooth® Audio functions are no longer functioning with customer's phone such as ability to change the track using the steering wheel controls.
Safety Recall an
Service Bulletin/Repair Instructions
Update on Technician Certification Requirements.
T-TT-0268-13 REV
Service Bulletin/Repair Instructions
TT: SOME CUSTOMERS MAY ENCOUNTER BLUETOOTH CONNECTIVITY CONCERNS SUCH AS: DIFFICULTY PAIRING THE PHONE. INTERMITTENT BLUETOOTH FAILURE TO CONNECT WHEN FIRST TURNING ON THE VEHICLE. VARIOUS BLUETOOTH AUDIO FUNCTIONS ARE NO LONGER FUNCTIONING WITH THE CUSTOMERS PHONE, SUCH AS THE ABILITY TO CHANGE THE TRACK USING THE STEERING WHEEL CONTROLS. THESE CONCERNS CAN BE CAUSED BY CHANGES MADE ON THE CUSTOMERS PHONE. MAKE SURE TO INQUIRE WITH THE CUSTOMER IF THE CONNECTIVITY CONCERNS OCCURRED AFTER RECEIVING AN OPERATING SYSTEM UPDATE ON THEIR PHONE OR IF THEY HAVE RESTORED THEIR PHONE DATA/SETTINGS RECENTLY.
TTT-0268-13 Rev3
Service Bulletin/Repair Instructions
TT: Some customers may encounter Bluetooth connectivity concerns such as: ? Difficulty pairing the phone. ? Intermittent Bluetooth failure to connect when first turning on the vehicle. ? Various Bluetooth Audio functions are no longer functioning with the customer?s phone, such as the ability to change the track using the steering wheel controls. These concerns can be caused by changes made on the customer?s phone. Make sure to inquire with the customer if the connectivity concerns occurred after receiving an operating system update on their phone or if they have restored their phone data/settings recently.
T-TT-0381-16
Service Bulletin/Repair Instructions
Tech Tip: Some customers may experience difficulty programming HomeLink.
T-TT-0362-15
Service Bulletin/Repair Instructions
TT: The vehicle may be difficult to start or have an abnormally low or rough idle after the battery has been disconnected or power to the Engine ECM has been interrupted.
T-TT-0360-15
Service Bulletin/Repair Instructions
TT: Customers may experience connectivity issues when the following conditions are met: The customer's iPhone is operating on iOS9 firmware. The customer's iPhone is connected to the vehicle via Bluetooth. The customer may complain of the following issues: When receiving two incoming calls simultaneously, both calls are ended automatically. iTunes Radio app does not play via Bluetooth audio. Podcast and Audiobook media playback is inoperative via Bluetooth audio.
T-TT-0355-15
Service Bulletin/Repair Instructions
TechTip: Condition: Customers may experience connectivity issues when the following conditions are met: The customer?s iPhone is operating on iOS9 firmware The customer?s iPhone is connected to the vehicle via Bluetooth. If the vehicle is equipped with a Fujitsu-Ten brand head unit, the customer may complain of one or more of the following: When playing media via Bluetooth audio and pressing the ?Pause? button on the phone, media playback pauses for one second before resuming playback. Yelp searches return an error when search criteria includes a special character, e.g. !,$,#. If the vehicle is equipped with a Pioneer brand head unit, the customer may complain of one or more of the following: The customer?s iPhone does not support the album image feature. When playing media via Bluetooth audio, one or more of a number of play/pause issues occur.
T-TT-0086-11
Service Bulletin/Repair Instructions
TechTip: Condition - The vehicle may be difficult to start or have an abnormally low or rough idle after the battery has been disconnected or power to the Engine ECM has been interrupted.
T-SB-0043-14 Rev
Service Bulletin/Repair Instructions
TSB: The Immobilizer and Smart Key Reset is a feature that allows the registration of new keys when all master keys are lost. Once the system is reset, all previously registered keys will be erased. Follow the procedures in this bulletin to reset a vehicle Immobilizer or Smart Key system. NOTE: There are new security provisions required to obtain a Reset Pass-Code. It is critical that the instructions for this new process are reviewed BEFORE attempting to get a Pass-Code in the new system.
T-SB-0039-15
Service Bulletin/Repair Instructions
TSB: Certain 2003 - 2011 model year Toyota vehicles may exhibit a condition where the instrument panel pad (dashboard) becomes cracked and/or has a shiny/degraded appearance. The pad surface may also become sticky or adherent. Follow the procedure in this bulletin to address this condition.
T-SB-0026-15
Service Bulletin/Repair Instructions
TSB: Some 2004 - 2015 model year Tacoma, FJ Cruiser, and 4Runner vehicles may exhibit a cyclical grinding or groaning noise coming from the front differential in 2WD that goes away when operated in 4WD. This noise can be addressed by replacing the needle bearing on the left side of the front differential. Refer to the Repair Procedure for Needle Bearing Roller replacement instructions.
T-SB-0083-13 Rev
Service Bulletin/Repair Instructions
TSB: The procedure in this bulletin is a general guideline on how to properly diagnose the air conditioning system after a component failure. Refer to the applicable Repair Manual for vehicle specific repair procedures and parts.
T-SB-0101-11 Rev
Service Bulletin/Repair Instructions
TSB: When servicing interior electrical switches and components, please note the precautions in this bulletin to avoid damaging electrical components and switches. Many lubricants, cleaners, and automotive chemicals contain silicone or other compounds that may contaminate electrical contacts, and therefore increase electrical resistance and decrease switch performance. The use of any cleaners or fluids may increase the risk of further damage to electrical components.
T-TT-0268-13 Rev
Service Bulletin/Repair Instructions
TT: Some customers may encounter Bluetooth® connectivity concerns such as: * Difficulty to pair the phone. * Intermittent Bluetooth® failure to connect to the vehicle when first turning on the vehicle. * Various Bluetooth® Audio functions are no longer functioning with customer's phone such as ability to change the track using the steering wheel controls. These concerns can be caused by changes made on the customer's phone. Make sure to inquire with the customer if the connectivity concerns occurred after receiving an operating system update on their phone or if they have restored their phone data/settings recently.
T-SB-0040-08
Service Bulletin/Repair Instructions
TSB: On some vehicles, when Rapgard is removed, the paint may have a stained appearance. These stains appear to be under the clear coat (repainting this area is not necessary). The stain patterns are usually under wrinkles in the Rapgard. These wrinkles sometimes trap water and cause the paint to stain from the trapped moisture, especially on horizontal surfaces, such as the hood, roof, and trunk. Stains can be removed by heating the stained surface to remove the trapped moisture.
T-SB-0012-13 REV
Service Bulletin/Repair Instructions
TSB: FLASH REPROGRAMMING ALLOWS THE ECU SOFTWARE TO BE UPDATED WITHOUT REPLACING THE ECU. FLASH CALIBRATION UPDATES FOR SPECIFIC VEHICLE MODELS/ECUS ARE RELEASED AS FIELD-FIX PROCEDURES DESCRIBED IN INDIVIDUAL SERVICE BULLETINS. THIS BULLETIN DETAILS THE TECHSTREAM ECU FLASH REPROGRAMMING PROCESS AND OUTLINES USE OF THE TECHNICAL INFORMATION SYSTEM (TIS) AND THE CALIBRATION UPDATE WIZARD (CUW). FLASH CALIBRATION UPDATES CAN ONLY BE APPLIED TO THE VEHICLE/ECU COMBINATION FOR WHICH THEY ARE INTENDED. ECUS HAVE INTERNAL SECURITY THAT WILL NOT ALLOW THEM TO BE PROGRAMMED WITH ANOTHER ECUS INFORMATION.
TSB-0012-13 Rev2
Service Bulletin/Repair Instructions
TSB: Flash reprogramming allows the ECU software to be updated without replacing the ECU. Flash calibration updates for specific vehicle models/ECUs are released as field-fix procedures described in individual Service Bulletins. This bulletin details the Techstream ECU flash reprogramming process and outlines use of the Technical Information System (TIS) and the Calibration Update Wizard (CUW). Flash calibration updates can only be applied to the vehicle/ECU combination for which they are intended. ECUs have internal security that will not allow them to be programmed with another ECU?s information.
ER10_Remail_Deal
Service Bulletin/Repair Instructions
Dealer Letter: Safety Recall completion is important not only in satisfying government requirements but also is an integral part of our commitment to meet customer expectations of Toyota products. Toyota will be sending Safety Recall Follow-Up Notices to remind owners whose vehicles have not yet had campaign repairs completed. We request your assistance in completing the applicable campaign repairs as owners receive the Follow-Up Notice and contact your dealership. Please note the follow-up activity may cause an increase in your current campaign owner appointments. Toyota will continue with additional follow-up activities in the months to come. Please take this into consideration when analyzing your manpower requirements.
ER10_Remail_Regi
Service Bulletin/Repair Instructions
Region Letter: Toyota will be sending Safety Recall Follow-Up Notices to remind owners whose vehicles have not yet had campaign repairs completed.
T-SB-0006-11 Rev
Service Bulletin/Repair Instructions
TSB: World Standard (WS) Automatic Transmission Fluid (ATF) was introduced to reduce maintenance costs and increase the mileage between scheduled maintenance checks. Here are some important tips when working with ATF-WS in Toyota vehicles requiring it's use.
T-SB-0014-11 Rev
Service Bulletin/Repair Instructions
TSB: The purpose of this service bulletin is to provide information regarding the installation of the correct torque converter bolts during automatic transmission/transaxle assembly replacement. Incorrect torque converter bolts or missing washers can cause damage to the torque converter assembly.
T-SB-0049-11 Rev
Service Bulletin/Repair Instructions
TSB: The purpose of this bulletin is to provide information regarding transmission and/or park neutral position switch installation. If the manual shift lever is rotated prior to installing the park neutral position switch, the detent spring may become detached from the manual shift lever.
T-SB-0260-08 Rev
Service Bulletin/Repair Instructions
TSB: The purpose of this bulletin is to assist in the identification and location of serial numbers on 2006 -2014 model year remanufactured automatic transmissions.
T-SB-0134-14
Service Bulletin/Repair Instructions
TSB: The purpose of this bulletin is to provide precautions to follow when installing an automatic transmission/transaxle assembly to avoid MIL "ON" shifting issues and/or transmission damage. Use the information in this bulletin when installing an automatic transmission/transaxle assembly.
T-SB-0200-08 Rev
Service Bulletin/Repair Instructions
TSB: The purpose of this bulletin is to assist in the identification and location of serial numbers on 2006 - 2014 model year automatic transmissions.
BST_Renotificati
Service Bulletin/Repair Instructions
Dealer Letter: Toyota will be sending Limited Service Campaign Notices to remind owners whose vehicles have not yet had Smart Stop Technology installed on their vehicle under LSC BST. Initial notification informing customers of the availability of Smart Stop Technology on certain models was handled by the court appointed administrator Gilardi and Company at the onset of the Class Action Settlement for Economic Loss. In addition to the initial notification, Toyota will be sending notifications to customers informing them of this LSC. These notifications are an integral part of our commitment to meet customer expectations of the Toyota products. We request your assistance in completing the Smart Stop Technology as owners receive the BST and contact your dealership. Please note the follow-up activity may cause an increase in your current campaign owner appointments.
TC-14-032
Service Bulletin/Repair Instructions
TOYOTA: ON SOME VEHICLES, INFORMATION BEING SENT OUT REGARDING INSTALLATION OF SMART STOP TECHNOLOGY. MODEL YEARS 2003-2010 COROLLA, COROLLA MATRIX, LAND CRUISER, HIGHLANDER RAV4, 4RUNNER, TUNDRA. *PE
T-SB-003-01 - OB
Service Bulletin/Repair Instructions
TSB: OBSOLETE NOTICE: July 7, 2014: This bulletin is now obsolete.
T-TT-0010-10 Rev
Service Bulletin/Repair Instructions
Tech Tip: Low battery voltage can contribute to a MIL "ON" condition for P0335 (Crankshaft Position Sensor Circuit) and/or P0340 (Camshaft Position Sensor Circuit) due to inconsistent rotational speed of the engine's crankshaft.
PHASE 3
Service Bulletin/Repair Instructions
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
LSC BST Phase 3
Service Bulletin/Repair Instructions
It has been brought to our attention that claim processing for LSC BST Phase 3 (2003-2009 4Runner and 2007-2010 Tundra vehicles) we be delayed until Monday April 7, 2014.
LSC BST Phase 1.
Service Bulletin/Repair Instructions
On July 24, 2013, the settlement of claims for Economic Loss arising from allegations of unintended acceleration was approved. As part of the settlement Toyota will be launching the third phase of a Limited Service Campaign to install Smart Stop technology on March 31, 2014., for the following models:
T-TT-0268-13
Service Bulletin/Repair Instructions
Customer complains of Bluetooth connectivity concerns such as: Difficulty to pair phone, Intermittent Bluetooth failure to connect to the vehicle when first turning on the vehicle. These concerns can be caused by changes made on the customer's phone. Make sure to inquire with the customer if the connectivity concerns occurred after receiving an operating system update on their phone or they have restored their phone data/settings recently.
T-TT-0132-11
Service Bulletin/Repair Instructions
A key part to maintain the proper function and safe operation of the vehicle's braking system is to perform a visual inspection when installing brake pads, calipers, and discs. The following recommendations are intended to provide general tips for the inspection and/or installation of Toyota Complete Maintenance Care (TCMC) front brake pads and discs. Always refer to the model specific Repair manual and TIS publications for specific repair instructions.
T-SB-0187-12 Rev
Service Bulletin/Repair Instructions
Toyota vehicles are equipped with either conventional or run-flat tires. Sometimes punctures may occur as a result of contact with road debris or other hazards. If a puncture occurs, it may be possible to repair the tire and return it to service. With a conventional tire it is not possible to drive for an extended amount of time with the tire at low pressures as damage to the tire may occur. With run-flat tires, due to reinforced sidewalls, it is possible to drive for up to 100 miles (160 km) at speeds less than 55 mph (90 km/h) with little or no damage to the tire.
T-TT-0213-13
Service Bulletin/Repair Instructions
Toyota vehicles are equipped with Supplemental Restraint Systems (SRS), including various airbags and in some models, seat belt pre-tensioners, to help reduce the risk of injury in a collision. If a customer expresses any concerns that the SRS airbags or pre-tensioner devices did not perform as expected (including an unintended deployment event), please follow the steps in the recommendations section below.
T-SB-0185-13
Service Bulletin/Repair Instructions
The following procedures are recommended during routine maintenance or in the event of a customer concern for wiper performance.
TS-BO030-01 Obso
Service Bulletin/Repair Instructions
This bulletin is now obsolete. Please see T-SB-0185-13.
T-SB-0122-11 Rev
Service Bulletin/Repair Instructions
Beginning in 1998, Toyota introduced side airbags as optional equipment. Toyota does NOT recommend replacement of original seat covers with non-Toyota leather or other seat cover materials on vehicles due to the following: Seat covers NOT recommended by Toyota may affect side airbag performance, in general or in part, during an accident. Modifications that negatively affect side airbag performance can result in severe occupant injuries. Seat covers are an integral part of this safety system. Replacing fabric seat covers with non-Toyota leather or other seat cover materials may compromise the effectiveness of this safety system. The design of the seat is complex, integrating safety and strength with comfort and luxury. Toyota strongly discourages modifying original equipment seats that have optional side airbags. Additionally, Toyota strongly advises against the installation or use of aftermarket seat covers, which could impair the performance of the side airbags in the event of an accident.
T-TT-0269-13
Service Bulletin/Repair Instructions
The appearance of spots in tempered glass (when viewed at certain angles) is the result of the heat treating and quick quenching process during manufacturing.
T-SB-0230-12 Rev
Service Bulletin/Repair Instructions
Some 2005 ? 2009 model year 4Runner, 2006 ? 2007 model year Land Cruiser, 2005 ? 2007 model year Sequoia, and 2005 ? 2006 model year Tundra vehicles equipped with the 2UZ-FE (4.7 L) engine may exhibit a MIL ?ON? condition for the following Diagnostic Trouble Codes (DTCs): ? P0412 ? Secondary Air Injection System Switching Valve ?A? Circuit ? P0418 ? Secondary Air Injection System Relay ?A? Circuit ? P1440/P1443 ? Secondary Air Injection System Control Valve Circuit Bank 1 / Bank 2 ? P1441/P1444 ? Secondary Air Injection System Switching Valve No. 2 Bank 1 / Bank 2 Stuck Open ? P2440 ? Secondary Air Injection System Switching Valve Stuck Open Bank 1 ? P1442/P1445 ? Secondary Air Injection System Switching Valve No. 2 Bank 1 / Bank 2 Stuck Close ? P2441 ? Secondary Air Injection System Switching Valve Stuck Close Bank 1 ? P2445 ? Secondary Air Injection System Pump Stuck Off Bank 1 This condition may be caused by debris passing through the air injection pump assembly and contaminating various components in the system. Use the following procedure to address this condition.
T-SB-0071-11 Rev
Service Bulletin/Repair Instructions
The purpose of this service bulletin is to provide precautions to follow when installing an automatic transmission/transaxle assembly to avoid MIL ?ON,? shifting issues, and/or transmission damage. Use the information in this bulletin when installing an automatic transmission/transaxle assembly
T-TT-0051-10
Service Bulletin/Repair Instructions
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
T-SB-0142-13
Service Bulletin/Repair Instructions
Some 2004 ? 2014 model year Toyota vehicles may exhibit odors naturally occurring from the HVAC system and/or related environmental factors. Although there is no way to eliminate these odors, follow the General Procedure in this bulletin to minimize the odors experienced.
T-SB-0141-13
Service Bulletin/Repair Instructions
A new Special Service Tool (SST 09709-00002) has been introduced to aid in the inspection procedure for certain vehicles equipped with a floor pedal-type parking brake system. This bulletin references the correct method for installing the Brake Pedal Force Gauge. Refer to the appropriate Repair Manual for parking brake pedal travel inspection and adjustment specification.
TC13-019
Service Bulletin/Repair Instructions
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
T-TT-0124-11
Service Bulletin/Repair Instructions
Please refer to the following recommendations for the best practices for vehicle tire rotations.
T-TT-0092-11 Rev
Service Bulletin/Repair Instructions
Some customers may complain that the Rear Seat Entertainment (RSE) system is inoperative if the have misplaced the parental passcode for the system.
T-PG006-00 Obsol
Service Bulletin/Repair Instructions
This bulletin is now obsolete. Please see T-SB-0054-13.
T-SB-0054-13
Service Bulletin/Repair Instructions
California (CA), Federal (FED), and 50 State Certified emission control underhood labels (emission labels) may be obtained through your dealership?s Parts Department utilizing standard replacement parts ordering procedures. Follow the guidelines outlined in this bulletin to ensure proper label application.
T-SB-0141-10 Rev
Service Bulletin/Repair Instructions
If a creak, tick, or rattle noise is heard at the top or bottom of the windshield, or at the top of the rear glass, the source of the noise may be the two stoppers bonded to the top of the windshield/rear glass, or the windshield retainers bonded to the lower edge of the windshield. This bulletin provides the recommended repair procedure to eliminate these types of noises from the windshield/rear glass area.
Renotification (
Service Bulletin/Repair Instructions
Toyota will be sending Safety Recall Follow Up Notices to remind owners whose vehicles have not yet had campaign repair completed. Please note the following information for Regional and PD associates.
T-TT-0226-13
Service Bulletin/Repair Instructions
The customer is having difficulty changing the multi-display screen from Day Mode. If the multi-display screen is set to Day Mode when the headlights are on, the setting we be memorized when the engine is turned off.
T-SB-0391-08 Rev
Service Bulletin/Repair Instructions
This bulletin contains general vehicle pulling diagnosis and repair procedures along with specific information to help correct pulling complaints.
SST Requirements
Service Bulletin/Repair Instructions
SSTs are key elements to provide your customers with swift and accurate repairs resulting in superior customer satisfaction.
T-SB-0012-13
Service Bulletin/Repair Instructions
Flash reprogramming allows the ECU software to be updated without replacing the ECU. Flash calibration updates for specific vehicle models/ECUs are released as field-fix procedures described in individual Service Bulletins. This bulletin details the Techstream ECU flash reprogramming process and outlines use of the TIS and the CUW.
T-SB-0064-10 Rev
Service Bulletin/Repair Instructions
This bulletin is now obsolete. Please see T-SB-0012-13.
T-SB-0230-12
Service Bulletin/Repair Instructions
Some 2005 - 2009 model year 4Runner, 2006 - 2007 model year Land Cruiser, 2005 - 2007 model year Sequoia, and 2005 - 2006 model year Tundra vehicles equipped with the 2UZ-FE (4.7 L) engine may exhibit a MIL "ON" condition for the following Diagnostic Trouble Codes (DTCs): P0412 - Secondary Air Injection System Switching Valve "A" Circuit P0418 - Secondary Air Injection System Relay "A" Circuit P1440/P1443 - Secondary Air Injection System Control Valve Circuit Bank 1 I Bank 2 P1441/P1444 - Secondary Air Injection System Switching Valve No. 2 Bank 1 I Bank 2 Stuck Open P2440 - Secondary Air Injection System Switching Valve Stuck Open Bank 1 P1442/P1445 - Secondary Air Injection System Switching Valve No. 2 Bank 1 I Bank 2 Stuck Close P2441 - Secondary Air Injection System Switching Valve Stuck Close Bank 1 P2445 - Secondary Air Injection System Pump Stuck Off Bank 1 This condition may be caused by debris passing through the air injection pump assembly and contaminating various components in the system. Use the following procedure to address this condition.
T-SB-0187-12
Service Bulletin/Repair Instructions
Toyota vehicles are equipped with either conventional or run-flat tires. Sometimes punctures may occur as a result of contact with road debris or other hazards. If a puncture occurs, it may be possible to repair the tire and return it to service. With a conventional tire it is not possible to drive for an extended amount of time with the tire at low pressures as damage to the tire may occur. With run-flat tires, due to reinforced sidewalls, it is possible to drive for up to 100 miles (160 km) at speeds less than 55 mph (90 km/h) with little or no damage to the tire.
T-SB-0187-12 R1
Service Bulletin/Repair Instructions
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
TSB-0087-12
Service Bulletin/Repair Instructions
TOYOTA: ACCELERATOR PEDAL SENSOR ASSEMBLY INFORMATION REGARDING THE INSPECTION, REMOVAL, AND INSTALLATION, IF LUBRICATION OR OIL, IS APPLIED. *PE
T-SB-0122-11
Service Bulletin/Repair Instructions
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
TSB-0122-11
Service Bulletin/Repair Instructions
TOYOTA: INFORMATION PROVIDED FOR REPLACING THE SEAT COVERS FOR VEHICLES EQUIPPED WITH SIDE AIRBAGS. *PE
TSB-0049-11
Service Bulletin/Repair Instructions
TOYOTA: INFORMATION ON INSTALLING MANUAL TRANSMISSION SHIFT LEVER OR PARK NEUTRAL POSITION SWITCH. *RM
TSB-0064-10
Service Bulletin/Repair Instructions
TOYOTA: TECHSTREAM ECU FLASH REPROGRAMMING PROCEDURE. FLASH REPROGRAMMING ALLOWS THE ECU SOFTWARE TO BE UPDATED WITHOUT REPLACING THE ECU. FLASH CALIBRATION UPDATES FOR SPECIFIC VEHICLE MODELS/ECUS ARE RELEASED AS FIELD-FIX PROCEDURES DESCRIBED IN INDIVIDUAL SERVICE BULLETINS. MODEL YEARS FROM 2001-2011. *PE
TSB-0086-09
Service Bulletin/Repair Instructions
TOYOTA: FOR VEHICLES THAT MAY EXHIBIT DIAGNOSTIC TROUBLE CODE (DTC) B0111 AND/OR B0116, A NEW SERVICE PART HAS BEEN MADE AVAILABLE. *PE
00207
Service Bulletin/Repair Instructions
HVAC BLOWER MOTOR ICE BUILD UP. *KB
00406
Service Bulletin/Repair Instructions
DIRECT-TYPE TIRE PRESSURE WARNING SYSTEM DIAGNOSTIC TIPS. *KB
00104
Service Bulletin/Repair Instructions
DIRECT TIRE PRESSURE WARNING SYSTEM. *TT UPDATED JAN. 24, 2007. *KB
T-PG007-01
Service Bulletin/Repair Instructions
Replacement vin plates.
T-PG002-91
Service Bulletin/Repair Instructions
Product general information.