Vehicle report

2024 TOYOTA CROWN

Compare every TOYOTA CROWN yearNHTSA and EPA records

Service bulletins

62 bulletins

Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.

T-SB-0051-26

Service Bulletin/Repair Instructions

This bulletin includes basic procedures for performing a rescue charge at battery on high voltage (HV) Ni-MH and Li-ion batteries.

T-SB-0110-20 Rev2

Service Bulletin/Repair Instructions

OBSOLETE NOTICE August 20, 2026: This bulletin is now obsolete. Please see T-SB-0051-26.

22TE09

Warranty Program/Extension

Although the HV Floor Under Wire Harness and Rear Traction Motor Cable is covered by Toyota’s New Vehicle Limited Warranty for 3 years or 36,000 miles (whichever comes first), we at Toyota care about the customers’ ownership experience. Toyota is providing extended coverage under this Customer Support Program for repairs related to excessive corrosion to the wire harness connections at the Rear Motor Generator. Excessive corrosion can cause AM Radio Static during certain drive cycles, or the vehicle may not start.

T-SB-0104-21 Rev2

Service Bulletin/Repair Instructions

OBSOLETE NOTICE February 27, 2026: This bulletin is no longer applicable and is now obsolete.

T-SB-0055-24 Rev2

Service Bulletin/Repair Instructions

Some 2005 – 2026 Toyota vehicles that have undergone water intrusion may exhibit a condition in which a musty odor is present. Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this Service Bulletin is to provide general guidelines and procedures for odor remediation. This Service Bulletin provides a guide on how to prepare and treat the interior of the vehicle for odor remediation. Refer to the applicable model and model year Repair Manual and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines.

25TD01

Service Campaign

The subject vehicles are equipped with a rear motor unit and an HV Floor Under Wire that provide high voltage to operate the motor. Mud, water, or road salt could potentially enter the HV Floor Underwire connector housing and could cause corrosion over time. Excessive corrosion could cause AM Radio Static during certain driving cycles, or the vehicle may not start.

T-SB-0058-23 Rev1

Service Campaign

The air conditioning dye injection tool kit has been developed to aid in identifying the location of air conditioning refrigerant leaks. The procedures outlined in this Service Bulletin aid in locating, inspecting, and repairing refrigerant leaks.

T-TT-0779-25

Service Bulletin/Repair Instructions

To assist with the early detection and early resolution of audio related concerns you may be asked to recover MMR data from the head unit. The following steps are instructions on how to retrieve the data from the system and are only to be used when requested by FTS and/or FPE.

T-SB-0028-25

Service Bulletin/Repair Instructions

Some 2023 – 2025 Crown and 2024 – 2025 Grand Highlander Hybrid vehicles equipped with a Hybrid Transmission Assembly HPC60 may exhibit a shudder sensation when the vehicle is at a complete stop, the State of Charge (SOC) of the HV Battery is greater than 76%, and the transmission is in the Drive position with the brakes applied.

T-SB-0107-20 Rev2

Service Bulletin/Repair Instructions

OBSOLETE NOTICE February 11, 2025: This bulletin is now obsolete. Please see T-SB-0021-25.

T-SB-0013-24 Rev1

Service Bulletin/Repair Instructions

The Immobilizer and Smart Key Reset is a feature that allows the registration of new keys when all master keys are lost. Once the system is reset, all previously registered keys will be erased and can never be reused. Another feature, Add/Remove Key, is also available. Once a key is removed, it can never be reused.

T-SB-0021-25

Service Bulletin/Repair Instructions

Flash reprogramming allows the Electronic Control Unit (ECU) software to be updated without replacing the ECU. Flash calibration updates for specific vehicle models/ECUs are released as field-fix procedures described in individual Service Bulletins. This bulletin details the Global Techstream+ (GTS+) ECU flash reprogramming procedures and outlines use of the Technical Information System (TIS) and the Calibration Update Wizard+ (CUW+). To ensure the correct ECU software is installed, ECUs will require a Security Signature before the ECU will initialize the flash reprogramming sequence. This bulletin also details the process for acquiring a Security Signature from TIS during the GTS+ ECU flash reprogramming process.

T-SB-0015-25

Service Bulletin/Repair Instructions

Some 2021 – 2025 model year Toyota vehicles may require the download and installation of vehicle specific software or configuration software when the Electronic Control Unit (ECU) is replaced. GTS+ software has been modified to indicate when configuration software is required. A new Configure column has been added to the GTS+ Health Check Results screen to show when configuration software is available for a specific ECU.

T-SB-0011-25

Service Bulletin/Repair Instructions

23TJ01P5_RL_Publ

Service Bulletin/Repair Instructions

RL: The supply of Smart Keys available for Toyota vehicles has been temporarily limited to one (1) on select models since October 2022 due to global semiconductor shortages impacting certain microchips. Affected vehicles have been delivered with only one Smart Key and a second mechanical key.

23TJ01P5_TI_Publ

Service Bulletin/Repair Instructions

TI: TECHNICAL INSTRUCTIONS FOR 23TJ01 Second Key Delivery Program Multiple Models and Model Years

23TJ01_P5_Dealer

Service Bulletin/Repair Instructions

DP: The subject vehicles were delivered with only one (1) Smart Key on select models since October 2022 due to a global semiconductor shortage impacting certain microchips. The affected vehicles were delivered with one (1) Smart Key and a second mechanical key.

T-SB-0035-24 Rev2

Service Bulletin/Repair Instructions

Acid rain results from rainwater or other airborne moisture that become acidic due to industrial chemical impurities in the atmosphere. If these acidic compounds settle on an exposed vehicle, especially the horizontal areas such as the hood, roof, and decklid, significant damage to the painted surfaces can occur. Acid rain damage can typically be identified on vehicles by the presence of stains on the paint surface that resemble hard water spots. Unlike water spots however, acid rain damage cannot be removed by regular washing procedures. Also, because acid rain can etch and soften the paint, normal buffing or polishing repair procedures should not be attempted. This can cause further damage and result in visible depressions in the paint surface. The following are the three major categories of acid rain damage: •Minor damage: requires only buffing to repair. •Moderate damage: usually requires neutralizing, color sanding, and buffing. •Severe damage: extending beyond 1/2 mil of clearcoat on a pearl, metallic, or solid color, requires neutralization, sanding, and repainting. In cases where acid rain damage is minor, neutralization and buffing with a liquid-type paint finessing product may provide an adequate repair. Only specially formulated products outlined in this bulletin should be used for that purpose. Unfortunately, other than minor damage, there is no simple method of determining the actual extent (depth) of acid penetration other than color sanding a representative affected area until there is no visible etching or depressions, followed by measuring the amount of paint removed with either a magnetic or digital-type film thickness gauge. The procedures in this bulletin are intended for use by qualified body/paint technicians and should not be attempted by inexperienced personnel. It is the dealer’s responsibility to protect and maintain the quality of the vehicle’s paint finish after receipt at the dealership prior to the first sale. Perform frequent vehicle washing, as often as daily, during high heat and humidity periods to minimize the potential for paint damage due to acid rain exposure. This is especially important in geographical areas known for high frequency and concentration of acid rain and industrial fallout.

T-SB-0038-24 Rev2

Service Bulletin/Repair Instructions

To prevent brake rotor rust from forming during transportation and storage, wheel film will be used instead of a cardboard type of anti-rust cover. The purpose of the wheel film is to shield the disc brake rotor from weather elements and initial rust before the vehicle is delivered to the customer. Consequently, the film should remain on the wheel for as long as possible.

T-SB-0039-24 Rev2

Service Bulletin/Repair Instructions

The condition known as acid rain is caused by airborne chemicals or particles in the atmosphere, which mix with rainwater, nighttime dew, or high humidity to form acidic compounds. If these contaminants settle and remain on a painted vehicle surface, especially the horizonal areas of the hood, roof, and decklid, significant damage can occur. This damage is the result of actual etching of the paint and appears as pitting or water spots. As acid rain droplets on the vehicle surface evaporate, the concentration strength of the acid increases, causing deeper and more rapid damage. This evaporation and corrosive action also occur more rapidly on dark colored cars as direct sun heat increases. It is the dealer’s responsibility to protect and maintain the quality of the vehicle’s paint finish after receipt at the dealership prior to the first sale. In areas known for high frequency and/or concentration of acid rain, frequent vehicle washing during high heat or humidity periods will minimize the potential for paint damage caused by acid rain. It is further recommended that either reverse osmosis or deionized water be used to prevent water spotting.

T-SB-0061-23 Rev2

Service Bulletin/Repair Instructions

Toyota vehicles are currently protected with RapgardTM protective film designed to protect the horizontal painted surfaces. This material protects from acid rain, environmental fallout, and rail contamination. Follow the Removal Procedure in this bulletin to remove the RapgardTM protective film within 90 days from initial application.

T-SB-0062-23 Rev2

Service Bulletin/Repair Instructions

Vehicles may occasionally be subjected to contamination by airborne iron particles shed from railroad tracks, train wheels, exposure to heavy machinery facilities, grinding, welding, etc. This type of contamination can be identified by the presence of small, red or brown particles on the paint surface. These particles are often difficult to see on dark color paints but can be easily felt when brushing a hand across horizontal body surfaces such as the hood, roof, or deck lid. Follow the Repair Procedure in this bulletin to clean vehicles that may have been subjected to contamination by airborne iron particles such as rail dust during rail transportation or extended storage near industrial areas.

23TJ01

Other

The table below describes the phases currently planned for the Second Key Delivery Program and the estimated timing of announcement. This table will be updated during each phase launch and as more details become available.

T-SB-0098-24

Service Bulletin/Repair Instructions

Some 2022 model year Avalon and Avalon Hybrid, 2022 – 2024 model year Camry, Camry Hybrid, Corolla, Corolla Hatchback, Corolla Hybrid, Highlander, Highlander Hybrid, Prius, Prius Prime, RAV4, RAV4 Hybrid, RAV4 Prime, and Venza Hybrid, 2023 – 2024 model year Crown, and 2024 model year Grand Highlander vehicles may exhibit a high-pitched noise coming from the front HVAC blower motor while operating the air conditioner or heater. This condition does not affect the operation of the vehicle, however, a heater cover has been developed to help reduce or potentially eliminate the noise.

T-TT-0765-24

Service Bulletin/Repair Instructions

Some 2023-2024, Camry, Camry HV, Crown, RAV4, and RAV4 HV, may exhibit an oil leak from the cylinder head cover, near the union of the timing chain cover and cam housing.

T-SB-0062-24 Rev1

Service Bulletin/Repair Instructions

Some 2023 model year RAV4 Prime vehicles with Data Communication Module (DCM) firmware version earlier than LG-N210hh1V1V-09 may exhibit a condition in which the remote climate system is inoperative after the vehicle has been off for three hours or more. Some 2023 model year Corolla, Corolla Cross, Corolla Cross Hybrid, Corolla Hatchback, Corolla Hybrid, Crown, GR Corolla, Highlander, Highlander Hybrid, Prius, Prius Prime, RAV4, RAV4 Hybrid, RAV4 Prime, and Venza Hybrid vehicles and 2024 model year Grand Highlander and Grand Highlander Hybrid vehicles with DCM firmware versions earlier than LG-N210jj3333-09, LG-N210nn1212-09, LG-N310kk4646-0I, LG-N310ll4A4A-0I, LG-N310mm8A8A-0I, LG-N310nnBLBM-0I, or LG-N310oo1B1B-0I may exhibit a condition in which remote services are inoperative. Some 2023 model year Corolla, Corolla Cross, Corolla Cross Hybrid, Highlander, and Highlander Hybrid vehicles, 2023 – 2024 model year Corolla Hybrid, GR Corolla, Prius, Prius Prime, RAV4, RAV4 Hybrid, RAV4 Prime, and Venza Hybrid vehicles, 2024 model year Grand Highlander, Grand Highlander Hybrid, and Land Cruiser vehicles; 2023 – 2025 Corolla Hatchback and Crown vehicles, and 2025 Crown Signia vehicles with DCM firmware versions earlier than LG-N210qq####-## or LG-N310qq####-## may exhibit a condition in which Apple Music® or Amazon Music streaming and/or remote services are inoperative. A DCM firmware update is now available.

T-SB-0055-24 Rev1

Service Bulletin/Repair Instructions

Some 2005 – 2024 Toyota vehicles that have undergone water intrusion may exhibit a condition in which a musty odor is present. Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this Service Bulletin is to provide general guidelines and procedures for odor remediation. This Service Bulletin provides a guide on how to prepare and treat the interior of the vehicle for odor remediation. Refer to the applicable model and model year Repair Manual and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines. This Service Bulletin is to provide a general overview and direction for the odor remediation process.

T-SB-0035-24 Rev1

Service Bulletin/Repair Instructions

T-SB-0038-24 Rev1

Service Bulletin/Repair Instructions

T-SB-0039-24 Rev1

Service Bulletin/Repair Instructions

The condition known as acid rain is caused by airborne chemicals or particles in the atmosphere, which mix with rainwater, nighttime dew, or high humidity to form acidic compounds. If these contaminants settle and remain on a painted vehicle surface, especially the horizonal areas of the hood, roof, and decklid, significant damage can occur. This damage is the result of actual etching of the paint and appears as pitting or water spots. As acid rain droplets on the vehicle surface evaporate, the concentration strength of the acid increases, causing deeper and more rapid damage. This evaporation and corrosive action also occur more rapidly on dark colored cars as direct sun heat increases. It is the dealer’s responsibility to protect and maintain the quality of the vehicle’s paint finish after receipt at the dealership prior to the first sale. In areas known for high frequency and/or concentration of acid rain (see Figure 1), frequent vehicle washing during high heat or humidity periods will minimize the potential for paint damage caused by acid rain. It is further recommended that either reverse osmosis or deionized water be used to prevent water spotting.

T-SB-0056-24

Service Bulletin/Repair Instructions

Some 2023 – 2024 model year Crown and 2024 model year Grand Highlander Hybrid vehicles equipped with the PC60 hybrid transmission may exhibit a MIL ON condition with Diagnostic Trouble Code (DTC) P279762 (Electromagnetic Oil Pump Component Internal Failure) present. The Transmission Control Module (TCM) logic has been modified to reduce the possibility of this condition.

T-SB-0055-24

Service Bulletin/Repair Instructions

T-SB-0103-20 Rev1

Service Bulletin/Repair Instructions

This Service Bulletin provides updated non-electric water pump leak inspection and diagnostic tips for some 2008 – 2025 model year Toyota vehicles.

T-TT-0694-22 Rev2

Service Bulletin/Repair Instructions

After jump-starting, the vehicle may experience a no-start condition and multiple DTCs including U010087. Upon investigation, it is found that the engine ECU has been damaged and needs to be replaced. In several cases, it was found that the cause of the ECU damage was improper jump starting. Further investigation found that ECU damage may occur if the negative (ground) cable clamps are attached on or around the engine ECU or ECU mounting bracket.

T-SB-0052-24

Service Bulletin/Repair Instructions

Some 2023 – 2024 Crown and 2024 model year Grand Highlander Hybrid vehicles equipped with a T24A-FTS engine may exhibit a MIL ON condition with Diagnostic Trouble Code (DTC) P05CE00 (Cold Start “B” Camshaft Position Timing Performance Bank 1) present. The Engine Control Module (ECM) (SAE term: Powertrain Control Module/PCM) logic has been modified to reduce the possibility of this condition.

T-SB-0061-23 Rev1

Service Bulletin/Repair Instructions

T-SB-0062-23 Rev1

Service Bulletin/Repair Instructions

T-SB-0035-24

Service Bulletin/Repair Instructions

Acid rain results from rainwater or other airborne moisture that become acidic due to industrial chemical impurities in the atmosphere. If these acidic compounds settle on an exposed vehicle, especially the horizontal areas such as the hood, roof, and decklid, significant damage to the painted surfaces can occur. Acid rain damage can typically be identified on vehicles by the presence of stains on the paint surface that resemble hard water spots. Unlike water spots however, acid rain damage cannot be removed by regular washing procedures. Also, because acid rain can etch and soften the paint, normal buffing or polishing repair procedures should not be attempted. This can cause further damage and result in visible depressions in the paint surface. The following are the three major categories of acid rain damage: •Minor damage: requires only buffing to repair. •Moderate damage: usually requires neutralizing, color sanding, and buffing. •Severe damage: extending beyond 1/2 mil of clearcoat on a pearl, metallic, or solid color, requires neutralization, sanding, and repainting. In cases where acid rain damage is minor, neutralization and buffing with a liquid-type paint finessing product may provide an adequate repair. Only specially formulated products outlined in this bulletin should be used for that purpose. Unfortunately, other than minor damage, there is no simple method of determining the actual extent (depth) of acid penetration other than color sanding a representative affected area until there is no visible etching or depressions, followed by measuring the amount of paint removed with either a magnetic or digital-type film thickness gauge. The procedures in this bulletin are intended for use by qualified body/paint technicians and should not be attempted by inexperienced personnel. While the quality and durability of paint on Toyota vehicles is continuously being improved, it remains the dealer’s responsibility to protect and maintain the quality of the vehicle’s paint finish after receipt at the dealership prior to the first sale. To read, While the quality and durability of paint on Toyota vehicles is continuously being improved, it remains the dealer’s responsibility to protect and maintain the quality of the vehicle’s paint finish after receipt at the dealership prior to first sale. Perform frequent vehicle washing, as often as daily, during high heat and humidity periods to minimize the potential for paint damage due to acid rain exposure. This is especially important in geographical areas known for high frequency and concentration of acid rain and industrial fallout.

T-SB-0038-24

Service Bulletin/Repair Instructions

T-SB-0039-24

Service Bulletin/Repair Instructions

The condition known as acid rain is caused by airborne chemicals or particles in the atmosphere, which mix with rainwater, nighttime dew, or high humidity to form acidic compounds. If these contaminants settle and remain on a painted vehicle surface, especially the horizonal areas of the hood, roof, and decklid, significant damage can occur. This damage is the result of actual etching of the paint and appears as pitting or water spots. As acid rain droplets on the vehicle surface evaporate, the concentration strength of the acid increases, causing deeper and more rapid damage. This evaporation and corrosive action also occur more rapidly on dark colored cars as direct sun heat increases. While Toyota paint quality, durability, and resistance to environmental factors is continuously being improved, it remains the responsibility of the dealer to protect and maintain the vehicle’s paint finish from the time of arrival at the dealership until retail delivery to the customer. In areas known for high frequency and/or concentration of acid rain (see Figure 1), frequent vehicle washing during high heat or humidity periods will minimize the potential for paint damage caused by acid rain. It is further recommended that either reverse osmosis or deionized water be used to prevent water spotting.

T-SB-0120-20 Rev2

Service Bulletin/Repair Instructions

Some 2021 – 2024 model year Toyota vehicles may require the download and installation of vehicle specific software or configuration software when the Electronic Control Unit (ECU) is replaced. GTS+ software has been modified to indicate when configuration software is required. A new Configure column has been added to the GTS+ Health Check Results screen to show when configuration software is available for a specific ECU. REVISION NOTICE April 18, 2024 Rev2: •Applicability has been updated to include 2024 model year Tundra, Tundra Hybrid, Venza Hybrid, bZ4X, Corolla, Corolla Cross, Corolla Cross Hybrid, Corolla Hybrid, Crown, GR Corolla, Corolla Hatchback, Prius, Prius Prime, Sequoia Hybrid, Highlander, Grand Highlander, Grand Highlander Hybrid, Land Cruiser, Tacoma, Tacoma Hybrid, and Mirai vehicles and 2023 model year Corolla Hatchback and Prius Prime vehicles. •The Introduction section has been updated. •The Operation Procedure section has been removed. •The Standard ECU Configuration Procedure and ECU Configuration Value Writing Procedure sections have been added.

23TJ01 Eligibility

Service Campaign

The table describes the phases currently planned for the Second Key Delivery Program and the estimated timing of announcement. This table will be updated during each phase launch and as more details become available.

T-SB-0111-20 Rev2

Service Bulletin/Repair Instructions

When certain vehicle ECUs are replaced, the ECU Security Key must be written in order for that ECU to communicate on the vehicle network. The GTS+ Software Health Check Results screen has been enhanced to help identify if a replacement ECU requires an ECU Security Key. REVISION NOTICE April 11, 2024 Rev2: •Applicability has been updated to include 2023 – 2024 model year 86, Corolla, Corolla Cross, Corolla Cross Hybrid, Crown, GR Corolla, Mirai, Prius, Prius Prime, RAV4 Prime, Sequoia Hybrid, Sienna Hybrid, Tundra, Tundra Hybrid, Venza Hybrid, and Yaris and 2024 model year bZ4X, Highlander, Highlander Hybrid, Grand Highlander, and Grand Highlander Hybrid vehicles. •The entire bulletin has been updated to represent GTS+ Software. July 08, 2022 Rev1: •Applicability has been updated to include 2022 model year 86, Corolla Cross, Mirai, Tundra, and Tundra Hybrid vehicles and 2023 model year bZ4X vehicles. Any previous printed versions of this bulletin should be discarded.

Toyota Second Ke

Service Bulletin/Repair Instructions

T-PANT-2024-004-

Service Bulletin/Repair Instructions

This is to advise of various price adjustments that will affect Toyota Genuine Motor Oil and Long Life Coolant, effective March 1, 2024. These products are ordered through the Toyota Complete Maintenance Care (TCMC) website.

T-SB-0013-24

Service Bulletin/Repair Instructions

TSB: The Immobilizer and Smart Key Reset is a feature that allows the registration of new keys when all master keys are lost. Once the system is reset, all previously registered keys will be erased and can never be reused. Another feature, Add/Remove Key, is also available. Once a key is removed, it can never be reused.

TSB002623

Service Bulletin/Repair Instructions

TSB: Long-term or off-site storage requires special care to keep vehicles factory fresh and ready for delivery. The following guidelines should be performed to minimize vehicle component/part degradation due to extended vehicle storage conditions. Long-term storage can affect a vehicle?s systems and components. Any problems that are found should be corrected immediately.

TSB002723

Service Bulletin/Repair Instructions

TSB: During the manufacturing process, tires are mounted on the vehicle as matched sets to help reduce conditions such as pulling or drifting. If the wheels are replaced or refinished before vehicle delivery, it is important that the tires remain on the vehicle in the same location and in the same direction of rotation. Refer to the Tire Positioning Procedure in this bulletin to ensure that the original tires stay in the same location on the vehicle.

TSB010421

Service Bulletin/Repair Instructions

TSB: Some 2018 ? 2024 model year Toyota vehicles equipped with an A25A-FKS, A25A-FXS, M20A-FKS, or M20A-FXS engine may exhibit one or more of the following conditions: ?Milky/discolored engine oil. ?An ?Oil Pressure Low? warning message on the Multi-information Display (MID). ?A MIL ON condition with Diagnostic Trouble Codes (DTCs) P05202A (Engine Oil Pressure Sensor/Switch ?A? Signal Stuck in Range) and/or P052477 (Engine Oil Pressure Too Low [Severe]) present. Moisture from blow-by gases condenses and accumulates in the engine oil during short trips in extreme cold weather. When the moisture in the oil freezes, the oil pressure may drop, and the aforementioned warning indicators may display. Follow the procedures in this bulletin to address these conditions.

TSB002423

Service Bulletin/Repair Instructions

TSB: A battery in a stored vehicle is subject to conditions that can reduce its performance and service life. These conditions include storage period, temperature, parasitic drain, and battery load. Because of these factors, battery inspection and maintenance are required in order to ensure proper operation and optimal battery life. As a matter of policy, Toyota does not provide battery warranty coverage for discharged and/or failed batteries due to lack of maintenance. It is the dealer?s responsibility to maintain the specified State-Of-Charge (SOC) of the vehicle?s battery while in stock and ensure proper SOC at delivery. To eliminate customer service concerns due to an undercharged battery during the first few weeks of ownership, All dealers should test the auxiliary (12V) battery and recharge, if necessary, no more than 48 hours before delivery to the customer.

TSB002823

Service Bulletin/Repair Instructions

TSB: 2024 model year Toyota vehicles are equipped with driver side floor mat retainers to secure the floor mat in the correct position. In addition, some models may also utilize retainers for passenger side and rear seat floor mats. During Pre-Delivery Service (PDS), follow the appropriate Installation Procedure to attach the driver side, and if applicable, the passenger side and rear seat floor mats to the vehicle carpet using the floor mat retainers. If installation instructions are included in the floor mat kit, place the instructions in the vehicle?s glove box for customer reference.

Current Phase Ti

Service Bulletin/Repair Instructions

Dealer Packet

Service Bulletin/Repair Instructions

Dealer Letter

Service Bulletin/Repair Instructions

T-SB-0080-23

Service Bulletin/Repair Instructions

TSB: Pre-Delivery Service (PDS) is a critical step in satisfying our new car customers. Customer feedback indicates the following areas deserve special attention when performing PDS: ?Careful inspection for paint chips/scratches and body dents/dings. ?Proper operation of electrical accessories (including interior light, clock, and radio reset). ?Interior cleanliness. ?Proper function of mechanical systems. Customer retention and proper maintenance of vehicles are and have always been a major focus for Toyota. To help remind customers that regular service is essential to the proper maintenance of the vehicle, dealers are required to install a service reminder sticker before delivery. By doing this, customers will be reminded to return to your dealership for service. Your current service reminder sticker may be used. (See PDS Check Sheet item 8 of ?Final Inspection and Cleaning.?) This bulletin contains the PDS procedures that apply specifically to 2024 model year Crown vehicles. A universal PDS Check Sheet that contains PDS steps that apply to all 2024 model year Toyota vehicles has been developed. To properly perform a complete PDS, you must complete all procedures contained in this TSB as well as the universal PDS Check Sheet. In addition, if the vehicle is stored for over 30 days, be sure to follow Long-Term Vehicle Storage Guidelines.

LSB001923

Service Bulletin/Repair Instructions

TTT073723

Service Bulletin/Repair Instructions

TT: A very small percentage of customers experience operational difficulties with some telematics features which they cannot resolve on their own. These resources, in conjunction with the Repair Manual, are for dealership personnel to assist those customers with user issues, user errors, and compatibility issues with other vehicle systems and external applications encountered while operating telematics features. Toyota has developed and provided the following Telematics Diagnostic Guide to assist dealer technicians.

T-SB-0107-20

Service Bulletin/Repair Instructions

TSB: Flash reprogramming allows the Electronic Control Unit (ECU) software to be updated without replacing the ECU. Flash calibration updates for specific vehicle models/ECUs are released as field-fix procedures described in individual Service Bulletins. This bulletin details the Global Techstream+ (GTS+) ECU flash reprogramming procedures and outlines use of the Technical Information System (TIS) and the Calibration Update Wizard+ (CUW+). To ensure the correct ECU software is installed, ECUs will require a Security Signature before the ECU will initialize the flash reprogramming sequence. This bulletin also details the process for acquiring a Security Signature from TIS during the GTS+ ECU flash reprogramming process.

T-SB-0042-23

Service Bulletin/Repair Instructions

TSB: Some 2023 ? 2024 model year Toyota vehicles use hub bolts in place of studs/nuts to fasten the wheels to the vehicle. If non-compatible wheels or hub bolts/nuts are installed, there is increased risk that the wheel(s) could come off resulting in a crash. This service bulletin outlines the physical differences and precautions that should be taken when servicing different wheel and wheel fastener types.

T-SB-0026-23

Service Bulletin/Repair Instructions

T-SB-0027-23

Service Bulletin/Repair Instructions

T-TT-0734-23

Service Bulletin/Repair Instructions

TT: When setting up the Toyota Audio Multimedia (21MM) user profile, if the QR code is not working please use the following recommendations.

Reading this report

Complaint counts are reports filed with NHTSA, not failure rates. A common model collects more of them than a rare one that breaks more often.