Vehicle report
Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
T-SB-0009-26
This bulletin includes basic procedures for performing a rescue charge on Ni-MH high voltage (HV) batteries. This bulletin should be used in conjunction with the applicable model and model year Repair Manual while performing a rescue charge. The GRX-5100 should be used wherever the Repair Manual references the Toyota Hybrid System (THS) charger.
T-SB-0119-15 Rev2
OBSOLETE NOTICE February 13, 2026: This bulletin is now obsolete. Please see T-SB-0009-26.
T-SB-0055-24 Rev2
Some 2005 – 2026 Toyota vehicles that have undergone water intrusion may exhibit a condition in which a musty odor is present. Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this Service Bulletin is to provide general guidelines and procedures for odor remediation. This Service Bulletin provides a guide on how to prepare and treat the interior of the vehicle for odor remediation. Refer to the applicable model and model year Repair Manual and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines.
T-SB-0035-24 Rev2
Acid rain results from rainwater or other airborne moisture that become acidic due to industrial chemical impurities in the atmosphere. If these acidic compounds settle on an exposed vehicle, especially the horizontal areas such as the hood, roof, and decklid, significant damage to the painted surfaces can occur. Acid rain damage can typically be identified on vehicles by the presence of stains on the paint surface that resemble hard water spots. Unlike water spots however, acid rain damage cannot be removed by regular washing procedures. Also, because acid rain can etch and soften the paint, normal buffing or polishing repair procedures should not be attempted. This can cause further damage and result in visible depressions in the paint surface. The following are the three major categories of acid rain damage: •Minor damage: requires only buffing to repair. •Moderate damage: usually requires neutralizing, color sanding, and buffing. •Severe damage: extending beyond 1/2 mil of clearcoat on a pearl, metallic, or solid color, requires neutralization, sanding, and repainting. In cases where acid rain damage is minor, neutralization and buffing with a liquid-type paint finessing product may provide an adequate repair. Only specially formulated products outlined in this bulletin should be used for that purpose. Unfortunately, other than minor damage, there is no simple method of determining the actual extent (depth) of acid penetration other than color sanding a representative affected area until there is no visible etching or depressions, followed by measuring the amount of paint removed with either a magnetic or digital-type film thickness gauge. The procedures in this bulletin are intended for use by qualified body/paint technicians and should not be attempted by inexperienced personnel. It is the dealer’s responsibility to protect and maintain the quality of the vehicle’s paint finish after receipt at the dealership prior to the first sale. Perform frequent vehicle washing, as often as daily, during high heat and humidity periods to minimize the potential for paint damage due to acid rain exposure. This is especially important in geographical areas known for high frequency and concentration of acid rain and industrial fallout.
T-SB-0038-24 Rev2
To prevent brake rotor rust from forming during transportation and storage, wheel film will be used instead of a cardboard type of anti-rust cover. The purpose of the wheel film is to shield the disc brake rotor from weather elements and initial rust before the vehicle is delivered to the customer. Consequently, the film should remain on the wheel for as long as possible.
T-SB-0039-24 Rev2
The condition known as acid rain is caused by airborne chemicals or particles in the atmosphere, which mix with rainwater, nighttime dew, or high humidity to form acidic compounds. If these contaminants settle and remain on a painted vehicle surface, especially the horizonal areas of the hood, roof, and decklid, significant damage can occur. This damage is the result of actual etching of the paint and appears as pitting or water spots. As acid rain droplets on the vehicle surface evaporate, the concentration strength of the acid increases, causing deeper and more rapid damage. This evaporation and corrosive action also occur more rapidly on dark colored cars as direct sun heat increases. It is the dealer’s responsibility to protect and maintain the quality of the vehicle’s paint finish after receipt at the dealership prior to the first sale. In areas known for high frequency and/or concentration of acid rain, frequent vehicle washing during high heat or humidity periods will minimize the potential for paint damage caused by acid rain. It is further recommended that either reverse osmosis or deionized water be used to prevent water spotting.
T-SB-0061-23 Rev2
Toyota vehicles are currently protected with RapgardTM protective film designed to protect the horizontal painted surfaces. This material protects from acid rain, environmental fallout, and rail contamination. Follow the Removal Procedure in this bulletin to remove the RapgardTM protective film within 90 days from initial application.
T-SB-0062-23 Rev2
Vehicles may occasionally be subjected to contamination by airborne iron particles shed from railroad tracks, train wheels, exposure to heavy machinery facilities, grinding, welding, etc. This type of contamination can be identified by the presence of small, red or brown particles on the paint surface. These particles are often difficult to see on dark color paints but can be easily felt when brushing a hand across horizontal body surfaces such as the hood, roof, or deck lid. Follow the Repair Procedure in this bulletin to clean vehicles that may have been subjected to contamination by airborne iron particles such as rail dust during rail transportation or extended storage near industrial areas.
T-SB-0055-24 Rev1
Some 2005 – 2024 Toyota vehicles that have undergone water intrusion may exhibit a condition in which a musty odor is present. Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this Service Bulletin is to provide general guidelines and procedures for odor remediation. This Service Bulletin provides a guide on how to prepare and treat the interior of the vehicle for odor remediation. Refer to the applicable model and model year Repair Manual and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines. This Service Bulletin is to provide a general overview and direction for the odor remediation process.
T-SB-0035-24 Rev1
Acid rain results from rainwater or other airborne moisture that become acidic due to industrial chemical impurities in the atmosphere. If these acidic compounds settle on an exposed vehicle, especially the horizontal areas such as the hood, roof, and decklid, significant damage to the painted surfaces can occur. Acid rain damage can typically be identified on vehicles by the presence of stains on the paint surface that resemble hard water spots. Unlike water spots however, acid rain damage cannot be removed by regular washing procedures. Also, because acid rain can etch and soften the paint, normal buffing or polishing repair procedures should not be attempted. This can cause further damage and result in visible depressions in the paint surface. The following are the three major categories of acid rain damage: •Minor damage: requires only buffing to repair. •Moderate damage: usually requires neutralizing, color sanding, and buffing. •Severe damage: extending beyond 1/2 mil of clearcoat on a pearl, metallic, or solid color, requires neutralization, sanding, and repainting. In cases where acid rain damage is minor, neutralization and buffing with a liquid-type paint finessing product may provide an adequate repair. Only specially formulated products outlined in this bulletin should be used for that purpose. Unfortunately, other than minor damage, there is no simple method of determining the actual extent (depth) of acid penetration other than color sanding a representative affected area until there is no visible etching or depressions, followed by measuring the amount of paint removed with either a magnetic or digital-type film thickness gauge. The procedures in this bulletin are intended for use by qualified body/paint technicians and should not be attempted by inexperienced personnel. It is the dealer’s responsibility to protect and maintain the quality of the vehicle’s paint finish after receipt at the dealership prior to the first sale. Perform frequent vehicle washing, as often as daily, during high heat and humidity periods to minimize the potential for paint damage due to acid rain exposure. This is especially important in geographical areas known for high frequency and concentration of acid rain and industrial fallout.
T-SB-0038-24 Rev1
To prevent brake rotor rust from forming during transportation and storage, wheel film will be used instead of a cardboard type of anti-rust cover. The purpose of the wheel film is to shield the disc brake rotor from weather elements and initial rust before the vehicle is delivered to the customer. Consequently, the film should remain on the wheel for as long as possible.
T-SB-0039-24 Rev1
The condition known as acid rain is caused by airborne chemicals or particles in the atmosphere, which mix with rainwater, nighttime dew, or high humidity to form acidic compounds. If these contaminants settle and remain on a painted vehicle surface, especially the horizonal areas of the hood, roof, and decklid, significant damage can occur. This damage is the result of actual etching of the paint and appears as pitting or water spots. As acid rain droplets on the vehicle surface evaporate, the concentration strength of the acid increases, causing deeper and more rapid damage. This evaporation and corrosive action also occur more rapidly on dark colored cars as direct sun heat increases. It is the dealer’s responsibility to protect and maintain the quality of the vehicle’s paint finish after receipt at the dealership prior to the first sale. In areas known for high frequency and/or concentration of acid rain (see Figure 1), frequent vehicle washing during high heat or humidity periods will minimize the potential for paint damage caused by acid rain. It is further recommended that either reverse osmosis or deionized water be used to prevent water spotting.
T-SB-0055-24
Some 2005 – 2024 Toyota vehicles that have undergone water intrusion may exhibit a condition in which a musty odor is present. Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this Service Bulletin is to provide general guidelines and procedures for odor remediation. This Service Bulletin provides a guide on how to prepare and treat the interior of the vehicle for odor remediation. Refer to the applicable model and model year Repair Manual and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines.
T-SB-0061-23 Rev1
Toyota vehicles are currently protected with RapgardTM protective film designed to protect the horizontal painted surfaces. This material protects from acid rain, environmental fallout, and rail contamination.
T-SB-0062-23 Rev1
Vehicles may occasionally be subjected to contamination by airborne iron particles shed from railroad tracks, train wheels, exposure to heavy machinery facilities, grinding, welding, etc. This type of contamination can be identified by the presence of small, red or brown particles on the paint surface. These particles are often difficult to see on dark color paints but can be easily felt when brushing a hand across horizontal body surfaces such as the hood, roof, or deck lid.
T-SB-0035-24
Acid rain results from rainwater or other airborne moisture that become acidic due to industrial chemical impurities in the atmosphere. If these acidic compounds settle on an exposed vehicle, especially the horizontal areas such as the hood, roof, and decklid, significant damage to the painted surfaces can occur. Acid rain damage can typically be identified on vehicles by the presence of stains on the paint surface that resemble hard water spots. Unlike water spots however, acid rain damage cannot be removed by regular washing procedures. Also, because acid rain can etch and soften the paint, normal buffing or polishing repair procedures should not be attempted. This can cause further damage and result in visible depressions in the paint surface. The following are the three major categories of acid rain damage: •Minor damage: requires only buffing to repair. •Moderate damage: usually requires neutralizing, color sanding, and buffing. •Severe damage: extending beyond 1/2 mil of clearcoat on a pearl, metallic, or solid color, requires neutralization, sanding, and repainting. In cases where acid rain damage is minor, neutralization and buffing with a liquid-type paint finessing product may provide an adequate repair. Only specially formulated products outlined in this bulletin should be used for that purpose. Unfortunately, other than minor damage, there is no simple method of determining the actual extent (depth) of acid penetration other than color sanding a representative affected area until there is no visible etching or depressions, followed by measuring the amount of paint removed with either a magnetic or digital-type film thickness gauge. The procedures in this bulletin are intended for use by qualified body/paint technicians and should not be attempted by inexperienced personnel. While the quality and durability of paint on Toyota vehicles is continuously being improved, it remains the dealer’s responsibility to protect and maintain the quality of the vehicle’s paint finish after receipt at the dealership prior to the first sale. To read, While the quality and durability of paint on Toyota vehicles is continuously being improved, it remains the dealer’s responsibility to protect and maintain the quality of the vehicle’s paint finish after receipt at the dealership prior to first sale. Perform frequent vehicle washing, as often as daily, during high heat and humidity periods to minimize the potential for paint damage due to acid rain exposure. This is especially important in geographical areas known for high frequency and concentration of acid rain and industrial fallout.
T-SB-0038-24
To prevent brake rotor rust from forming during transportation and storage, wheel film will be used instead of a cardboard type of anti-rust cover. The purpose of the wheel film is to shield the disc brake rotor from weather elements and initial rust before the vehicle is delivered to the customer. Consequently, the film should remain on the wheel for as long as possible. SUPERSESSION NOTICE The information contained in this bulletin supersedes Service Bulletin No. PD017-04. •The entire bulletin has been updated.
T-SB-0039-24
The condition known as acid rain is caused by airborne chemicals or particles in the atmosphere, which mix with rainwater, nighttime dew, or high humidity to form acidic compounds. If these contaminants settle and remain on a painted vehicle surface, especially the horizonal areas of the hood, roof, and decklid, significant damage can occur. This damage is the result of actual etching of the paint and appears as pitting or water spots. As acid rain droplets on the vehicle surface evaporate, the concentration strength of the acid increases, causing deeper and more rapid damage. This evaporation and corrosive action also occur more rapidly on dark colored cars as direct sun heat increases. While Toyota paint quality, durability, and resistance to environmental factors is continuously being improved, it remains the responsibility of the dealer to protect and maintain the vehicle’s paint finish from the time of arrival at the dealership until retail delivery to the customer. In areas known for high frequency and/or concentration of acid rain (see Figure 1), frequent vehicle washing during high heat or humidity periods will minimize the potential for paint damage caused by acid rain. It is further recommended that either reverse osmosis or deionized water be used to prevent water spotting.
T-PANT-2024-004-
This is to advise of various price adjustments that will affect Toyota Genuine Motor Oil and Long Life Coolant, effective March 1, 2024. These products are ordered through the Toyota Complete Maintenance Care (TCMC) website.
T-SB-0043-14
OBSOLETE NOTICE January 22, 2024: This bulletin is now obsolete. Please see T-SB-0057-18.
TSB003220
TSB: Replacement certification labels (the vinyl label installed on the driver door or door post) and VIN plates (the metal plate riveted to dashboard) (see Figure 1) for most 1979 ? 2023 model year vehicles may be available provided the requests meet the criteria listed in this Service Bulletin. Follow the Procurement Procedure in this bulletin to request a replacement certification label or VIN plate.
T-SB-0057-18
TSB: The Immobilizer and Smart Key Reset is a feature that allows the registration of new keys when all master keys are lost. Once the system is reset, all previously registered keys will be erased. Follow the procedures in this bulletin to reset a vehicle Immobilizer or Smart Key system.
Z2G_Dealer_Lette
DL: Toyota has received reports of paint peeling on certain vehicles with the original factory-applied Blizzard Pearl or Super White paint colors. These reports indicate that vehicles with these specific paint colors, applied during the vehicle manufacturing process, may experience paint peeling on exterior metal body panels. Although the original factory paint is covered by Toyota?s New Vehicle Limited Warranty for 3 years or 36,000 miles (whichever comes first), we at Toyota care about the customers? ownership experience. Toyota is providing coverage for repairs related to the condition described above. The following information is provided to inform you and your staff of the program notification schedule and your degree of involvement.
Z3G_Dealer_Lette
DL: Toyota has received reports of paint peeling on certain vehicles with the original factory-applied Blizzard Pearl or Super White paint colors. These reports indicate that vehicles with these specific paint colors, applied during the vehicle manufacturing process, may experience paint peeling on exterior metal body panels. Although the original factory paint is covered by Toyota?s New Vehicle Limited Warranty for 3 years or 36,000 miles (whichever comes first), we at Toyota care about the customers? ownership experience. Toyota is providing coverage for repairs related to the condition described above. The following information is provided to inform you and your staff of the program notification schedule and your degree of involvement.
ZKG_Dealer_Lette
DL: Toyota has received reports of paint peeling on certain vehicles with the original factory-applied Blizzard Pearl or Super White paint colors. These reports indicate that vehicles with these specific paint colors, applied during the vehicle manufacturing process, may experience paint peeling on exterior metal body panels. Although the original factory paint is covered by Toyota?s New Vehicle Limited Warranty for 3 years or 36,000 miles (whichever comes first), we at Toyota care about the customers? ownership experience. Toyota is providing coverage for repairs related to the condition described above. The following information is provided to inform you and your staff of the program notification schedule and your degree of involvement
T-SB-0094-21 Rev
TSB: Some 2005 ? 2022 model year Toyota vehicles that have undergone water intrusion may exhibit a condition in which a musty smell is present. Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this service bulletin is to provide general guidelines and procedures for odor remediation. This service bulletin provides a guide on how to prepare the interior of the vehicle prior to an odor remediation being performed, as well as contact information for an approved vendor who will arrange the remediation, and instructions on how to prepare the interior of the vehicle for reassembly once the remediation has been completed. Refer to all model and model year specific Repair Manuals and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines. This service bulletin is to provide a general overview and direction for the odor remediation process.
Z3G_Paint_Repair
CSP: Customer Support Program ZKG ? Paint Repair Process
Z3G_Technical_In
TI: TECHNICAL INSTRUCTIONS Customer Support Program ZKG Multiple Models and Model Years Vehicles Painted with Blizzard Pearl (070) or Super White (040) Paint Color Coverage for Peeling of Factory-Applied Paint
TSB001221Rev2
TSB: Some 2010 ? 2022 model year Toyota vehicles may exhibit paint stains after the removal of Rapgard?. The paint stains may appear to be under the clear coat but are usually under wrinkles in the Rapgard?. The wrinkles may trap water and cause the paint to stain from the trapped moisture, especially on horizontal surfaces such as the hood, roof, and trunk. Follow the Repair Procedure in this bulletin to address this condition
T-SB-0119-15 Rev
TSB: This bulletin includes basic procedures for performing a rescue charge on Ni-MH high voltage (HV) batteries. This bulletin should be used in conjunction with the applicable model and model year Repair Manual while performing a rescue charge. The GRX-5100 should be used wherever the Repair Manual references the Toyota Hybrid System (THS) charger
TSB009421Rev1
TSB: Some 2005 ? 2022 model year Toyota vehicles that have undergone water intrusion may exhibit a condition in which a musty smell is present. Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this service bulletin is to provide general guidelines and procedures for odor remediation. This service bulletin provides a guide on how to prepare the interior of the vehicle prior to an odor remediation being performed, as well as contact information for an approved vendor who will arrange the remediation, and instructions on how to prepare the interior of the vehicle for reassembly once the remediation has been completed. Refer to all model and model year specific Repair Manuals and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines. This service bulletin is to provide a general overview and direction for the odor remediation process
ZKG_Technical_In
TI: Technical Instructions Customer Support Program ZKG Multiple Models and Model Years Vehicles Painted with Blizzard Pearl (070) or Super White (040) Paint Color Coverage for Peeling of Factory-Applied Paint
TTT063620
TT: Some Toyota vehicles installed with Toyota Complete Maintenance Care (TCMC) brake pads may exhibit a groan or squeak noise in various driving conditions
T-SB-0012-21 Rev
TSB: Some 2010 ? 2022 model year Toyota vehicles may exhibit paint stains after the removal of Rapgard?. The paint stains may appear to be under the clear coat but are usually under wrinkles in the Rapgard?. The wrinkles may trap water and cause the paint to stain from the trapped moisture, especially on horizontal surfaces such as the hood, roof, and trunk. Follow the Repair Procedure in this bulletin to address this condition
T-SB-0094-21
TSB: Some 2005 ? 2022 model year Toyota vehicles that have undergone water intrusion may exhibit a condition in which a musty smell is present. Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this service bulletin is to provide general guidelines and procedures for odor remediation. This service bulletin provides a guide on how to prepare the interior of the vehicle prior to an odor remediation being performed, as well as contact information for an approved vendor who will arrange the remediation, and instructions on how to prepare the interior of the vehicle for reassembly once the remediation has been completed. Refer to all model and model year specific Repair Manuals and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines. This service bulletin is to provide a general overview and direction for the odor remediation process.
T-TT-0578-19 Rev
TT: Some customers may encounter Bluetooth® connectivity concerns such as: ?Difficulty to pair the phone. ?Intermittent Bluetooth® failure to connect to the vehicle when first turning on the vehicle. ?Various Bluetooth® Audio functions are no longer functioning with customer?s phone such as ability to change the track using the steering wheel controls. These concerns can be caused by changes made on the customer?s phone. Make sure to inquire with the customer if the connectivity concerns occurred after receiving an operating system update on their phone, or if they have restored their phone data/settings recently.
T-SB-0080-19 Rev
TSB: Some 2006 ? 2022 model year Toyota vehicles in particular geographic areas may exhibit a condition where the HVAC evaporator drain hose has become obstructed with an insect nest. An insect repellent drain hose tip (ARINIX® Tip) is available to help minimize future occurrences of this environmental condition. For some models, a new drain hose is required to properly fit the ARINIX® Tip. Follow the procedures in this bulletin for proper handling and installation of this optional service part.
21TE01 - 2012-20
RL: Although the Brake Booster and Brake Booster Pump Assemblies are covered by Toyota?s New Vehicle Limited Warranty for 3 years or 36,000 miles (whichever comes first), we at Toyota care about the customers? ownership experience. Toyota is providing coverage for repairs related to certain internal malfunctions of the Brake Booster and Brake Booster Pump Assemblies in some of the subject vehicles.
Customer Support
RE: Although the Brake Booster and Brake Booster Pump Assemblies are covered by Toyota?s New Vehicle Limited Warranty for 3 years or 36,000 miles (whichever comes first), we at Toyota care about the customers? ownership experience. Toyota is providing coverage for repairs related to certain internal malfunctions of the Brake Booster and Brake Booster Pump Assemblies in some of the subject vehicles. The following information is provided to inform you and your staff of the program notification schedule and your degree of involvement.
T-SB-0028-21
TSB: Some 2012 ? 2014 model year Prius C hybrid vehicles may exhibit a condition in which the brake, ABS, and/or TRAC warning lights are on and/or a Check VSC message displays. Diagnostic Trouble Codes (DTCs) C1391, C1252, C1256, and/or C1253 may also be stored. This condition may be caused by a small internal brake fluid leak inside the brake booster assembly with master cylinder. Follow the Repair Procedure in this bulletin to address this condition.
T-SB-0044-16 Obs
OBSOLETE NOTICE March 08, 2021: This bulletin is now obsolete. Please see T-SB-0012-21.
Toyota Safety Re
Toyota Safety Recall and Service Campaign - Technician Certification Requirements
T-TT-0636-20 Rev
TT: Some Toyota vehicles installed with Toyota Complete Maintenance Care (TCMC) brake pads may exhibit a groan or squeak noise in various driving conditions.
T-SB-0040-08 Obs
OBSOLETE NOTICE March 08, 2021: This bulletin is now obsolete. Please see T-SB-0044-16.
T-SB-0012-21
TSB: Some 2010 ? 2021 model year Toyota vehicles may exhibit paint stains after the removal of Rapgard?. The paint stains may appear to be under the clear coat but are usually under wrinkles in the Rapgard?. The wrinkles may trap water and cause the paint to stain from the trapped moisture, especially on horizontal surfaces such as the hood, roof, and trunk. Follow the Repair Procedure in this bulletin to address this condition.
T-SB-0032-20 Rev
TSB: Replacement certification labels (the vinyl label installed on the driver door or door post) and VIN plates (the metal plate riveted to dashboard) (see Figure 1) for most 1979 ? 2021 model year vehicles may be available provided the requests meet the criteria listed in this Service Bulletin. Follow the Procurement Procedure in this bulletin to request a replacement certification label or VIN plate.
T-TT-0636-20
TT: Some Toyota vehicles installed with Toyota Complete Maintenance Care (TCMC) brake pads may exhibit a groan or squeak noise in various driving conditions.
T-TT-0628-20
TT: HVAC drain tube is found to be blocked/clogged.
T-SB-0062-20 Rev
TSB: Some 2004 ? 2020 model year Hybrid vehicles may exhibit an excessive buildup of dust, lint, or debris in the HV battery intake filter or cooling fan. The condition could reduce the efficiency of the HV battery cooling system. Perform the procedures outlined in this bulletin to address this condition.
ZKG_Proper_Photo
ZKG WEBSITE PROPER PHOTOGRAPH SUBMISSION
T-TT-0468-17 Rev
TT: HVAC drain tube is found to be blocked/clogged.
T-SB-0062-20
TSB: Some 2004 ? 2020 model year Hybrid vehicles may exhibit an excessive buildup of dust, lint, or debris in the HV battery intake filter or cooling fan. The condition could reduce the efficiency of the HV battery cooling system. Perform the procedures outlined in this bulletin to address this condition.
T-SB-0119-15_Rev
TT: This bulletin includes basic procedures for performing a rescue charge on Ni-MH high voltage (HV) batteries. This bulletin should be used in conjunction with the applicable model and model year Repair Manual while performing a rescue charge. The GRX-5100 should be used wherever the Repair Manual references the Toyota Hybrid System (THS) charger.
T-SB-0304-17 Obs
TSB: OBSOLETE NOTICE April 07, 2020: This bulletin is now obsolete. Please see T-SB-0032-20. Replacement Certification Labels and VIN Plates
T-SB-0032-20
TSB: SUPERSESSION NOTICE The information contained in this bulletin supersedes Service Bulletin Nos. PG021-88, PG015-89, PG0015-90, PG002-91, PG002-93, PG005-97, PG007-01, PG007-07, PG006-01, PG004-97, T-SB-0144-08, and T-SB-0304-17. The aforementioned bulletins are obsolete, and any printed versions should be discarded. Replacement certification labels (the vinyl label installed on the driver door or door post) and VIN plates (the metal plate riveted to dashboard) (see Figure 1) for most 1979 ? 2020 model year vehicles may be available provided the requests meet the criteria listed in this Service Bulletin. Follow the Procurement Procedure in this bulletin to request a replacement certification label or VIN plate.
T-SB-0142-13_Obs
OBSOLETE NOTICE February 12, 2020: This bulletin is now obsolete. Please see T-SB-0010-20.
T-SB-0010-20
TSB: Some 2004 ? 2017 model year Toyota vehicles may exhibit odors naturally occurring from the HVAC system and/or related environmental factors. Although there is no way to eliminate these odors, follow the General Procedure in this bulletin to minimize the odors experienced
ZKG_Dealer Email
Toyota has received reports of paint peeling on certain vehicles with the original factory-applied Blizzard Pearl or Super White paint colors. These reports indicate that vehicles with these specific paint colors, applied during the vehicle manufacturing process, may experience paint peeling on exterior metal body panels. Although the original factory paint is covered by Toyota?s New Vehicle Limited Warranty for 3 years or 36,000 miles (whichever comes first), we at Toyota care about the customers? ownership experience. Toyota is providing coverage for repairs related to the condition described above. The following information is provided to inform you and your staff of the program notification schedule and your degree of involvement
ZKG_Paint_Repair
Customer Support Program ZKG ? Paint Repair Process OPERATION FLOW CHART
ZKG_Technical In
TECHNICAL INSTRUCTIONS Customer Support Program ZKG Phase 2 ? Customer Renotification and Repair Phase Repair is Now Available Multiple Models and Model Years Vehicles Painted with Blizzard Pearl (070) or Super White (040) Paint Color Coverage for Peeling of Factory-Applied Paint
T-SB-0008-20
TSB: Vehicles may display evidence of a fluid leak or fluid seep from powertrain components. This bulletin explains how to determine the differences between a fluid leak versus a fluid seep. Cases that are determined to be a ?leak? should be repaired accordingly and will be covered under warranty if applicable. Cases that are determined to be a ?seep? should be documented on the repair order and inspected at the next service interval. Follow the Repair Information in this bulletin to determine if the concern in question is a fluid leak or fluid seep and review the Repair Procedure section to address the condition. NOTE This bulletin applies to ALL powertrain fluids excluding fuel and coolant.
T-SB-0101-15_Obs
TSB: OBSOLETE NOTICE December 18, 2019: This bulletin is no longer applicable and is now obsolete.
ZKG_Dealer Packa
Dealer Package: Toyota has received reports of paint peeling on certain vehicles with the original factory-applied Blizzard Pearl or Super White paint colors. These reports indicate that vehicles with these specific paint colors, applied during the vehicle manufacturing process, may experience paint peeling on exterior metal body panels. Although the original factory paint is covered by Toyota?s New Vehicle Limited Warranty for 3 years or 36,000 miles (whichever comes first), we at Toyota care about the customers? ownership experience. Toyota is providing coverage for repairs related to the condition described above. The following information is provided to inform you and your staff of the program notification schedule and your degree of involvement.
ZKG_Paint Repair
Repair Process: Customer Support Program ZKG ? Paint Repair Process.
ZKG_Region Email
Region Email: Toyota has received reports of paint peeling on certain vehicles with the original factory-applied Blizzard Pearl or Super White paint colors. These reports indicate that vehicles with these specific paint colors, applied during the vehicle manufacturing process, may experience paint peeling on exterior metal body panels. Although the original factory paint is covered by Toyota?s New Vehicle Limited Warranty for 3 years or 36,000 miles (whichever comes first), we at Toyota care about the customers? ownership experience. Toyota is providing coverage for repairs related to the condition described above. The following information is provided to inform you and your staff of the program notification schedule and your degree of involvement.
ZKG_Region Lette
Region Letter: Toyota has received reports of paint peeling on certain vehicles with the original factory-applied Blizzard Pearl or Super White paint colors. These reports indicate that vehicles with these specific paint colors, applied during the vehicle manufacturing process, may experience paint peeling on exterior metal body panels. Although the original factory paint is covered by Toyota?s New Vehicle Limited Warranty for 3 years or 36,000 miles (whichever comes first), we at Toyota care about the customers? ownership experience. Toyota is providing coverage for repairs related to the condition described above.
T-TT-0578-19
TT: Some customers may encounter Bluetooth® connectivity concerns such as: ? Difficulty to pair the phone. ? Intermittent Bluetooth® failure to connect to the vehicle when first turning on the vehicle. ? Various Bluetooth® Audio functions are no longer functioning with customer?s phone such as ability to change the track using the steering wheel controls. These concerns can be caused by changes made on the customer?s phone. Make sure to inquire with the customer if the connectivity concerns occurred after receiving an operating system update on their phone, or if they have restored their phone data/settings recently.
T-SB-0033-14-Obs
TSB: OBSOLETE NOTICE July 9, 2019: This bulletin is now obsolete. Please see T-SB-0080-19.
T-SB-0080-19
TSB: SUPERSESSION NOTICE The information contained in this bulletin supersedes Service Bulletin No. T-SB-0033-14. ? Applicability has been updated to include 2019 model year Toyota vehicles. Service Bulletin No. T-SB-0033-14 is obsolete and any printed versions should be discarded. Some 2006 ? 2019 model year Toyota vehicles in particular geographic areas may exhibit a condition where the HVAC evaporator drain hose has become obstructed with an insect nest. An insect repellent drain hose tip (ARINIX® Tip) is available to help minimize future occurrences of this environmental condition. For some models, a new drain hose is required to properly fit the ARINIX® Tip. Follow the procedures in this bulletin for proper handling and installation of this optional service part. NOTE The ARINIX® Tip is NOT registered or labeled for sale or use outside the United States or Puerto Rico.
T-SB-0134-16-Rev
TSB: REVISION NOTICE July 01, 2019 Rev2: ? Applicability has been updated to 2019 ? 2020 model year Toyota vehicles. ? The Techstream Preparation and Process Overview sections have been updated. October 30, 2017 Rev1: ? Applicability has been updated to include 2018 model year vehicles. Any previous printed versions of this bulletin should be discarded. SUPERSESSION NOTICE The information contained in this bulletin supersedes SB No. T-SB-0012-13. Service Bulletin No. T-SB-0012-13 is obsolete and any printed versions should be discarded. Be sure to review the entire content of this bulletin before proceeding. Flash reprogramming allows the Electronic Control Unit (ECU) software to be updated without replacing the ECU. Flash calibration updates for specific vehicle models/ECUs are released as field-fix procedures described in individual Service Bulletins. This bulletin details the Techstream ECU flash reprogramming process and outlines use of the Technical Information System (TIS) and the Calibration Update Wizard (CUW). Flash calibration updates can only be applied to the vehicle/ECU combination for which they are intended. ECUs have internal security that will not allow them to be programmed with another ECU?s information. NOTE ECU is a Toyota term used to describe integrated computerized devices responsible for managing the operation of a system or subsystem. For the purposes of this bulletin, the term ?ECU? is used as a generic label for the following SAE J1930 standard references: ? Powertrain Control Module (PCM) ? Engine Control Module (ECM) ? Transmission Control Module (TCM) ? Any other Toyota specific control unit
TSR-SC-032819
Technician Certification Requirements.
T-TT-0414-16-Rev
TT: Some customers may encounter Bluetooth® connectivity concerns such as: ? Difficulty to pair the phone. ? Intermittent Bluetooth® failure to connect to the vehicle when first turning on the vehicle. ? Various Bluetooth® Audio functions are no longer functioning with customer?s phone such as ability to change the track using the steering wheel controls. These concerns can be caused by changes made on the customer?s phone. Make sure to inquire with the customer if the connectivity concerns occurred after receiving an operating system update on their phone, or if they have restored their phone data/settings recently.
T-SB-0044-16_Rev
TSB: REVISION NOTICE February 7, 2019 Rev2: * Applicability has been updated to include 2010 - 2014 model year Matrix, 2017 - 2019 model year C-HR, 2019 model year Corolla Hatchback, and 2018 - 2019 model year Toyota vehicles. G418 The Introduction and Repair Procedure sections have been updated. March 7, 2017 Rev1: * Applicability has been updated to include 2017 model year Toyota vehicles. Any previous printed versions of this bulletin should be discarded. SUPERSESSION NOTICE The information contained in this bulletin supersedes SB No. T-SB-0040-08. * Applicability has been updated to include applicable 2016 model year vehicles. Service Bulletin No. T-SB-0040-08 is obsolete and any printed versions should be discarded. Some 2010 - 2019 model year Toyota vehicles may exhibit paint stains after the removal of Rapgard. The paint stains may appear to be under the clear coat but are usually under wrinkles in the Rapgard. The wrinkles may trap water and cause the paint to stain from the trapped moisture, especially on horizontal surfaces, such as the hood, roof, and trunk. Follow the Repair Procedure in this bulletin to address this condition.
T-SB-0033-14_Rev
TSB: Some vehicles in particular geographic areas may exhibit a condition where the HVAC evaporator drain hose has become obstructed with an insect nest. An insect repellent drain hose tip (ARINIX® Tip) is now available to help minimize future occurrences of this environmental condition. For some models, a new drain hose is required to properly fit the ARINIX® Tip. Follow the procedures in this bulletin for proper handling and installation of this optional service part.
PG004-97-Obsolet
Technical Service Bulletin: OBSOLETE NOTICE: July 31, 2018: This bulletin is now obsolete. Please see T-SB-0304-17.
PG006-01-Obsolet
Technical Service Bulletin: OBSOLETE NOTICE: July 31, 2018: This bulletin is now obsolete. Please see T-SB-0304-17.
T-SB-0304-17_Rev
TSB: REVISION NOTICE July 31, 2018 Rev2: ? The Supersession Notice has been updated. January 11, 2018 Rev1: ? The Supersession Notice has been updated. Any previous printed versions of this bulletin should be discarded. SUPERSESSION NOTICE The information contained in this bulletin supersedes Service Bulletin Nos. PG021-88, PG015-89, PG0015-90, PG002-91, PG002-93, PG005-97, PG007-01, PG007-07, PG006-01, PG004-97, and T-SB-0144-08. Service Bulletin Nos. PG021-88, PG015-89, PG0015-90, PG002-91, PG002-93, PG005-97, PG007-01, PG007-07, PG006-01, PG004-97, and T-SB-0144-08 are obsolete and any printed versions should be discarded. Vehicle replacement certification labels (the vinyl label installed on the driver door or door post) and VIN plates (the metal plate riveted to dashboard) may be available from Toyota, provided the request meets one of the criteria listed in this Service Bulletin. Replacement Certification Label and VIN Plate Criteria A replacement certification label and/or VIN plate may be requested if: ? The vehicle was in an accident and the label and/or plate is damaged or attached to a part that will be replaced during the repair. ? The label and/or plate was stolen.
ZG8_Toyota POL17
Warranty Policy Bulletin: Toyota has received reports of customer concerns in which the vehicle may exhibit a combination of abnormal engine noise and rough idle caused by internal carbon deposit in the combustion chambers.
T-SB-0187-12_Rev
TSB: REVISION NOTICE February 12, 2018 Rev2: ? Applicability has been updated to include 2015 ? 2018 model year vehicles. January 23, 2014 Rev1: ? Applicability has been updated to include 2013 ? 2014 model year vehicles. Any previous printed versions of this bulletin should be discarded. Toyota vehicles are equipped with either conventional or run-flat tires. Sometimes punctures may occur as a result of contact with road debris or other hazards. If a puncture occurs, it may be possible to repair the tire and return it to service. With a conventional tire it is not possible to drive for an extended amount of time with the tire at low pressures as damage to the tire may occur. With run-flat tires, due to reinforced sidewalls, it is possible to drive for up to 100 miles at speeds less than 55 mph with little or no damage to the tire. The U.S. Tire Manufacturers Association (UTSMA) provides guidelines and recommendations for tire repair and replacement. It also provides information related to: ? Basic tire information ? Tire maintenance and safety ? Driver education, tire safety curriculum.
T-SB-0009-18
TSB: The purpose of this Service Bulletin is to elevate awareness and provide best practices for leather and synthetic leather care in Toyota vehicles. As an additional resource, if the vehicle is equipped with factory leather seats, the vehicle Owner?s Manual will highlight the importance of proper maintenance and provide guidance for care.
F0B_Expired_Deal
Dealer Package: January 8, 2018 A watermark has been added to the Dealer Letter to indicate that F0B expired on December 31, 2017 LSC Expired on December 31, 2017.
F0B_TI_EXPIRED_P
Technical Instructions: LSC Expired on December 31, 2017. TECHNICAL INSTRUCTIONS FOR LIMITED SERVICE CAMPAIGN F0B OCCUPANT CLASSIFICATION SYSTEM (OCS) SENSOR CERTAIN 2012 ? 2013 MODEL YEAR PRIUS C.
F0B_TI_EXPIRED_S
Technical Instructions: LSC Expired on December 31, 2017. TECHNICAL INSTRUCTIONS FOR LIMITED SERVICE CAMPAIGN F0B OCCUPANT CLASSIFICATION SYSTEM (OCS) SENSOR CERTAIN 2012 ? 2013 MODEL YEAR SIA CAMRY.
T-SB-0162-13_Rev
TSB: REVISION NOTICE January 05, 2018 Rev1: ? Applicability has been updated to include 2012 ? 2017 Camry HV and Prius C, 2015 ? 2017 Prius V, 2006 ? 2017 Highlander HV, 2010 ? 2016 Prius, and 2016 ? 2017 RAV4 HV model year vehicles. ? The Repair Procedure section has been updated. Any previous printed versions of this bulletin should be discarded. Some 2006 ? 2017 Highlander HV, 2010 ? 2016 Prius, 2012 ? 2017 Camry HV, Prius C and Prius V, and 2016 ? 2017 RAV4 HV model year vehicles used under certain severe operating conditions may exhibit an excessive buildup of dust, lint, or other debris in the HV battery cooling fan, which can reduce the efficiency of the HV battery cooling system. Follow the Repair Procedure in this bulletin to address this condition.
TSR-1212-17
Technician Certification Requirements.
T-SB-0229-12_Rev
TSB: REVISION NOTICE November 22, 2017 Rev1: ? Applicability has been updated to include 2014 ? 2018 model year vehicles. Any previous printed versions of this bulletin should be discarded. In the event that a Toyota vehicle becomes submerged in water, many components may be physically damaged. Electrical and electronic components, including wiring harnesses, are particularly susceptible to corrosion and subsequent malfunction. Although any flooding can be damaging, salt water flooding elevates the potential for abnormal conditions and may increase risks due to its highly corrosive and conductive nature. Salt residue also continues to corrode and remain conductive even after a vehicle dries. This bulletin is intended to assist with safe handling and inspection of flood damaged vehicles and to provide basic guidance on likely needed repairs.
ZE7-Toyota POL14
Warranty Policy Bulletin: Toyota has received some reports where vehicles may exhibit excessive engine oil consumption. Toyota is now announcing the part replacement phase of Warranty Enhancement Program ZE7 for vehicles exhibiting excessive engine oil consumption.
T-SB-0134-16_Rev
TSB: REVISION NOTICE October 30, 2017 Rev1: * Applicability has been updated to include 2018 model year vehicles. SUPERSESSION NOTICE The information contained in this bulletin supersedes SB No. T-SB-0012-13. Flash reprogramming allows the Electronic Control Unit (ECU) software to be updated without replacing the ECU. Flash calibration updates for specific vehicle models/ECUs are released as field-fix procedures described in individual Service Bulletins. This bulletin details the Techstream ECU flash reprogramming process and outlines use of the Technical Information System (TIS) and the Calibration Update Wizard (CUW). Flash calibration updates can only be applied to the vehicle/ECU combination for which they are intended. ECUs have internal security that will not allow them to be programmed with another ECU's information.
T-SB-0304-17
TSB: Vehicle replacement certification labels (the vinyl label installed on the driver door or door post) and VIN plates (the metal plate riveted to dashboard) may be available from Toyota, provided the request meets one of the criteria listed in this Service Bulletin.
T-SB-0218-17_Rev
TSB: REVISION NOTICE July 20, 2017 Rev1: Applicability has been updated to exclude 2007 ? 2017 model year Avanza vehicles. Some hazardous material treatment and handling regulations at the state and local level define the pre-disposal deployment of airbag and pre-tensioner assemblies as hazardous material treatment. Hazardous material treatment may require special training, certification or licensing in certain areas. TMS recommends that dealership personnel carefully review and follow ALL local and state regulations, and where necessary, contract with Environmental Protection Agency (EPA) Licensed Hazardous Waste Transportation and Disposal facilities.
T-TT-0432-17_Rev
TT: Rev2 Some Customers may complain about a Hybrid Vehicle Battery cooling system warning message. This warning message may appear when the HV Battery cooling system loses efficiency due to debris on the filter and or some object obstructing the air inlet. Refer to the information below to address this issue.
ZG8 Dealer Email
Dealer Email: Toyota is announcing a Warranty Enhancement Program to extend the warranty coverage for certain 2012 ? 2013 model year Scion iQ vehicles that exhibit a rough idle and abnormal noise condition caused by internal carbon deposit in the combustion chambers.
ZG8 Dealer Packa
Dealer Package: Toyota is announcing a Warranty Enhancement Program to extend the warranty coverage for certain 2012 ? 2013 model year Scion iQ vehicles that exhibit a rough idle and abnormal noise condition caused by internal carbon deposit in the combustion chambers.
ZG8 POL17-05 War
Warranty Policy Bulletin POL17-05: Toyota has received reports of customer concerns in which the vehicle may exhibit a combination of abnormal engine noise and rough idle caused by internal carbon deposit in the combustion chambers.
ZG8 Region Email
Region Email: Toyota is announcing a Warranty Enhancement Program to extend the warranty coverage for certain 2012 ? 2013 model year Scion iQ vehicles that exhibit a rough idle and abnormal noise condition caused by internal carbon deposit in the combustion chambers.
ZG8 Region Lette
Region Letter: In these vehicles, Toyota has received some reports where vehicles may exhibit a combination of abnormal engine noise and rough idle.
T-TT-0365-15_Rev
TT: Rev2 A vehicle may arrive to the dealer with a MIL ?ON? condition and P0A80 or P1AC000 stored in the memory. Some cases have been identified with internal modification done to the HV Battery. Modified or altered parts are not covered under warranty.
T-TT-0435-17
TT: This bulletin is regarding best practices when handling navigation systems that use Hard Disc Drive or Micro SD Card memory.
T-TT-0365-15 Rev
TT: A vehicle may arrive to the dealer with a MIL ?ON? condition and P0A80 or P1AC000 stored in the memory. Some cases have been identified with internal modification done to the HV Battery. Modified or altered parts are not covered under warranty.
TTT043217 Rev1
TT: Some Customers may complain about a Hybrid Vehicle Battery cooling system warning message. This warning message may appear when the HV Battery cooling system loses efficiency due to debris on the filter and or some object obstructing the air inlet.
TTT043217
TT: Some Customers may complain about a Hybrid Vehicle Battery cooling system warning message. This warning message may appear when the HV Battery cooling system loses efficiency due to debris on the filter and or some object obstructing the air inlet.
TSB018217
TSB: SUPERSESSION NOTICE The information contained in this bulletin supersedes SB No. T-SB-0101-11. Applicability has been updated to include 2016 ? 2017 model year vehicles. Service Bulletin No. T-SB-0101-11 is Obsolete and any printed versions should be discarded. Be sure to review the entire content of this bulletin before proceeding. When servicing interior electrical switches and components, please note the precautions in this bulletin to avoid damaging electrical components and switches. Many lubricants, cleaners, and automotive chemicals contain silicone or other compounds that may contaminate electrical contacts, and therefore increase electrical resistance and decrease switch performance. The use of any cleaners or fluids may increase the risk of further damage to electrical components.
T-SB-0012-13 Rev
TSB: OBSOLETE NOTICE: September 14, 2016: This bulletin is now obsolete. Please see T-SB-0134-16.
T-SB-0142-13 Rev
TSB: REVISION NOTICE November 10, 2016 Rev2: ? Applicability has been updated to include 2016 ? 2017 model year Toyota vehicles. ? Parts Information section has been updated. Some 2004 ? 2017 model year Toyota vehicles may exhibit odors naturally occurring from the HVAC system and/or related environmental factors. Although there is no way to eliminate these odors, follow the General Procedure in this bulletin to minimize the odors experienced.
ZE7_Warranty Pol
Warranty Policy Bulletin: Toyota has received some reports where vehicles may exhibit excessive engine oil consumption. Toyota is now announcing the part replacement phase of Warranty Enhancement Program ZE7 for vehicles exhibiting excessive engine oil consumption.
T-TT-0309-14 Rev
TT: Some customers may experience Bluetooth disconnections or loss of SMS text message functionality on the navigation/audio system with Android phones running OS 4.4 or later. Condition tends to occur to customers who have many previous text messages on their phones.
T-TT-0365-15
TT: A vehicle may arrive to the dealer with a MIL ?ON? condition and P0A80 stored in the memory. Some cases have been identified with internal modification done to the HV Battery. Modified or altered parts are not covered under warranty.
T-SB-0134-16
TSB: Supersession Notice. Flash reprogramming allows the ECU software to be updated without replacing the ECU. Flash calibration updates for specific vehicle models/ECUs are released as field-fix procedures described in individual Service Bulletins. This bulletin details the Techstream ECU flash reprogramming process and outlines use of the Technical Information System (TIS) and the Calibration Update Wizard (CUW). Flash calibration updates can only be applied to the vehicle/ECU combination for which they are intended. ECUs have internal security that will not allow them to be programmed with another ECU?s information.
T-TT-0414-16
TT: Some customers may encounter Bluetooth® connectivity concerns such as: *Difficulty to pair the phone. *Intermittent Bluetooth® failure to connect to the vehicle when first turning on the vehicle. *Various Bluetooth® Audio functions are no longer functioning with customer's phone such as ability to change the track using the steering wheel controls.
T-SB-0101-15 Rev
TSB: REVISION NOTICE August 23, 2016 Rev1: Applicability has been updated to include 2015 model year Prius and Prius PHV vehicles. Any previous printed versions of this bulletin should be discarded. Toyota models equipped with the Display Audio Navigation System require a Special Service Tool (SST) USB drive to update the map, points of interest, Gracenote®, and system software. The SST is used with all vehicles to deliver the update, however a unique Activation Number is required for each vehicle. Activation Numbers are provided in an Activation Card Number (ACN) pamphlet available through the normal parts ordering system. Use the process described in this bulletin to perform the update.
T-SB-0061-15 REV
TSB: REVISION NOTICE: INTRODUCTION HAS BEEN UPDATED. ANY PREVIOUS PRINTED VERSIONS OF THIS BULLETIN SHOULD BE DISCARDED. SOME 2012 MODEL YEAR VEHICLES EQUIPPED WITH A DISPLAY AUDIO NAVIGATION SYSTEM AND ENTUNE (VERSION LESS THAN 2.1.0) MAY EXHIBIT 1 OR MORE OF THE FOLLOWING CONDITIONS; SOME 2012 2013 MODEL YEAR VEHICLES EQUIPPED WITH A DISPLAY AUDIO NAVIGATION SYSTEM (NON-HDD) AND ENTUNE (VERSION LESS THAN 2.2.0) MAY EXHIBIT 1 OR MORE OF THE FOLLOWING CONDITIONS; SOME 2012 2014 MODEL YEAR VEHICLES EQUIPPED WITH A DISPLAY AUDIO NAVIGATION SYSTEM (NON-HDD) AND ENTUNE (VERSION LESS THAN 3.2.0) MAY EXHIBIT 1 OR MORE OF THE FOLLOWING CONDITIONS; SOME 2012 2015 MODEL YEAR VEHICLES EQUIPPED WITH A DISPLAY AUDIO NAVIGATION SYSTEM (NON-HDD) AND ENTUNE (VERSION LESS THAN 4.1.0) MAY EXHIBIT 1 OR MORE OF THE FOLLOWING CONDITIONS; SOME 2012 2015 MODEL YEAR VEHICLES EQUIPPED WITH A DISPLAY AUDIO NAVIGATION SYSTEM (NON-HDD) AND ENTUNE (VERSION LESS THAN 5.1.0) MAY EXHIBIT 1 OR MORE OF THE FOLLOWING CONDITIONS.
T-SB-0061-15 Rev
TSB: Revision Notice: Introduction has been updated. Any previous printed versions of this bulletin should be discarded. Some 2012 model year vehicles equipped with a Display Audio Navigation System and Entune (version less than 2.1.0) may exhibit 1 or more of the following conditions; Some 2012 - 2013 model year vehicles equipped with a Display Audio Navigation System (Non-HDD) and Entune (version less than 2.2.0) may exhibit 1 or more of the following conditions; Some 2012 - 2014 model year vehicles equipped with a Display Audio Navigation System (Non-HDD) and Entune (version less than 3.2.0) may exhibit 1 or more of the following conditions; Some 2012 - 2015 model year vehicles equipped with a Display Audio Navigation System (Non-HDD) and Entune (Version less than 4.1.0) may exhibit 1 or more of the following conditions; Some 2012 - 2015 model year vehicles equipped with a Display Audio Navigation System (Non-HDD) and Entune? (Version less than 5.1.0) may exhibit 1 or more of the following conditions.
Safety Recall an
Update on Technician Certification Requirements.
T-SB-0198-11 REV
TSB: FOR VEHICLES THAT ARE USED UNDER CERTAIN SEVERE OPERATING CONDITIONS, THE HV BATTERY COOLING FAN MAY EXPERIENCE AN EXCESSIVE BUILDUP OF DUST, LINT, OR OTHER DEBRIS THAT CAN REDUCE THE EFFICIENCY OF THE HV BATTERY COOLING SYSTEM. HV BATTERY COOLING FAN MAINTENANCE AND CLEANING SHOULD BE PERFORMED TO ADDRESS THIS CONDITION.
T-SB-0198-11 Rev
TSB: For vehicles that are used under certain severe operating conditions, the HV Battery Cooling Fan may experience an excessive buildup of dust, lint, or other debris that can reduce the efficiency of the HV Battery Cooling System. HV Battery Cooling Fan maintenance and cleaning should be performed to address this condition.
T-TT-0397-16
TT: Some customers may complain about a MIL ?ON? with a P0A80 DTC. In these cases, the HV Battery would need to be replaced. Along with the HV Battery replacement, the cooling system filter will need either cleaning or replacement. This TT provides information about the HV Battery cooling system filter.
T-SB-0044-16
TSB: On some vehicles, when Rapgard? is removed, the paint may have a stained appearance. These stains appear to be under the clear coat (repainting this area is not necessary). The stain patterns are usually under wrinkles in the Rapgard?. These wrinkles sometimes trap water and cause the paint to stain from the trapped moisture, especially on horizontal surfaces, such as the hood, roof, and trunk. Stains can be removed by heating the stained surface to remove the trapped moisture.
T-TT-0395-16
TT: HV Batteries have liquid filled cell modules, to prevent leakage from cells, it is very important to confirm the proper orientation mark of the DRC.
T-TT-0392-16 REV
TT: SOME CUSTOMERS MAY EXPERIENCE BLUETOOTH CONNECTION ISSUES AFTER UPDATING THE ANDROID OPERATING SYSTEM TO 5.X.X (LOLLIPOP) OR LATER.
T-TT-0392-16 Rev
TT: Some customers may experience Bluetooth connection issues after updating the Android Operating System to 5.x.x (Lollipop) or later.
T-TT-0392-16
TT: Some customers may experience Bluetooth connection issues after updating the Android Operating System to 5.x.x (Lollipop) or later.
T-TT-0374-15
TT: Since MY 2011, several different update or upgrade USB SSTs have been issued for Toyota audio and navigation systems. Refer to the chart below for a comprehensive list of all current and previously issued USB SSTs and their applicability.
T-TT-0374-15 REV
TT: SINCE MY 2011, SEVERAL DIFFERENT UPDATE OR UPGRADE USB SSTS HAVE BEEN ISSUED FOR TOYOTA AUDIO AND NAVIGATION SYSTEMS. REFER TO THE CHART BELOW FOR A COMPREHENSIVE LIST OF ALL CURRENT AND PREVIOUSLY ISSUED USB SSTS AND THEIR APPLICABILITY.
T-TT-0385-16
Tech Tip: This Tech Tip is being provided to bring attention to the new location of the Entune/NAV/Map Update and Upgrade USB Directory. Click on the TIS tab, Diagnostics tab, Telematics tab, and the document is now located under the reference documents sections. This change has occurred to help speed up the updating process of this document.
T-SB-0119-15
TSB: This bulletin includes basic procedures for performing a Rescue Charge on Ni-MH High Voltage (HV) Batteries. This bulletin should be used in conjunction with the Repair Manual while performing Rescue Charge. The GRX-5100 should be used wherever the Repair Manual references the Toyota Hybrid System (THS) Charger.
T-SB-0005-13 REV
TSB: OBSOLETE NOTICE NOVEMBER 2, 2015: THIS BULLETIN IS NOW OBSOLETE. PLEASE SEE T-SB-0101-15
T-SB-0005-13 Rev
TSB: Obsolete Notice November 2, 2015: This bulletin is now obsolete. Please see T-SB-0101-15
T-SB-0101-15
TSB: Toyota models equipped with the Display Audio Navigation System require a Special Service Tool (SST) USB drive to update the map, points of interest, Gracenote, and system software. The SST is used with all vehicles to deliver the update, however a unique Activation Card Number (ACN) required for each vehicle. Activation Numbers are provided in an Activation Card Number (ACN) pamphlet available through the normal parts ordering system. Use the process described in this bulletin.
T-TT-0234-13 REV
TT: SINCE MY 2011, SEVERAL DIFFERENT UPDATE OR UPGRADE USB SSTS HAVE BEEN ISSUED FOR TOYOTA AUDIO AND NAVIGATION SYSTEMS. REFER TO THE CHART BELOW FOR A COMPREHENSIVE LIST OF ALL CURRENT AND PREVIOUSLY ISSUED USB SSTS AND THEIR APPLICABILITY.
TTT-0234-13 Rev6
TT: Since MY 2011, several different update or upgrade USB SSTs have been issued for Toyota audio and navigation systems. Refer to the chart below for a comprehensive list of all current and previously issued USB SSTs and their applicability.
T-TT-0344-15 REV
TT: IPHONE TEXT MESSAGES DO NOT APPEAR ON MULTIMEDIA DIS[PLAY.
T-TT-0362-15
TT: The vehicle may be difficult to start or have an abnormally low or rough idle after the battery has been disconnected or power to the Engine ECM has been interrupted.
TTT-0344-15 Rev1
TT: iPhone text messages do not appear on multimedia dis[play.
T-TT-0086-11
TechTip: Condition - The vehicle may be difficult to start or have an abnormally low or rough idle after the battery has been disconnected or power to the Engine ECM has been interrupted.
T-SB-0051-13 Rev
TSB: August 19, 2015: This bulletin is now obsolete. Please see T-SB-0061-15
T-SB-0163-13 Rev
TSB: Use the following procedures to check and/or update the software version of Entune/Navigation for Non-HDD Type units.
T-SB-0051-13 REV
TSB: AUGUST 19, 2015: THIS BULLETIN IS NOW OBSOLETE. PLEASE SEE T-SB-0061-15
T-SB-0043-14 Rev
TSB: The Immobilizer and Smart Key Reset is a feature that allows the registration of new keys when all master keys are lost. Once the system is reset, all previously registered keys will be erased. Follow the procedures in this bulletin to reset a vehicle Immobilizer or Smart Key system. NOTE: There are new security provisions required to obtain a Reset Pass-Code. It is critical that the instructions for this new process are reviewed BEFORE attempting to get a Pass-Code in the new system.
T-TT-0344-15
TT: iPhone text messages do not appear on multimedia display.
T-TT-0234-13 Rev
TT: Since MY 2011, several different update or upgrade USB SSTs have been issued for Toyota audio and navigation systems. Refer to the chart below for a comprehensive list of all current and previously issued USB SSTs and their applicability.
T-TT-0294-14 Rev
TT: Greenhouse Gas Logic (GHC) has been implemented on Toyota A/C Systems to reduce tailpipe emissions. The federal government issues café (Corporate Average Fuel Economy) credits to vehicle manufacturers that implement new technologies that reduce the carbon footprint of the vehicles they produce. GHC Logic technology works by automatically operating the HVAC system in REC mode when certain operating conditions are met, improving the A/C systems cooling efficiency and reducing the vehicle's C02 emissions.
T-SB-0083-13 Rev
TSB: The procedure in this bulletin is a general guideline on how to properly diagnose the air conditioning system after a component failure. Refer to the applicable Repair Manual for vehicle specific repair procedures and parts.
T-TT-0337-15
TT: When updating either the navigation or radio firmware, verify the vehicle applicability BEFORE beginning the update.
F0B_LSC_Phase 2_
DL: The front passenger seat assembly is equipped with sensors for the occupant classification system which are used to control the operation of supplemental restraint systems (SRS), including the front passenger airbag. The sensors classify the weight of the occupant and activate or deactivate the front passenger airbag accordingly. Additionally, the sensors are used to detect certain vehicle collisions. Due to the current collision detection thresholds, the system may interpret certain occupant seating usages or road conditions as a rear collision and illuminate the Airbag Warning Light and "AIR BAG OFF" indicator, disabling the front passenger air bag.
F0B_LSC_Dealer L
DL: The front passenger seat assembly is equipped with sensors for the occupant classification system which are used to control the operation of supplemental restraint systems (SRS), including the front passenger airbag. The sensors classify the weight of the occupant and activate or deactivate the front passenger airbag accordingly. Additionally, the sensors are used to detect certain vehicle collisions. Due to the current collision detection thresholds, the system may interpret certain occupant seating usages or road conditions as a rear collision and illuminate the Airbag Warning Light and "AIR BAG OFF" indicator, disabling the front passenger air bag.
F0B_LSC_Region L
RL: The front passenger seat assembly is equipped with sensors for the occupant classification system which are used to control the operation of supplemental restraint systems (SRS), including the front passenger airbag. The sensors classify the weight of the occupant and activate or deactivate the front passenger airbag accordingly. Additionally, the sensors are used to detect certain vehicle collisions. Due to the current collision detection thresholds, the system may interpret certain occupant seating usages or road conditions as a rear collision and illuminate the Airbag Warning Light and "AIR BAG OFF" indicator, disabling the front passenger air bag.
T-SB-0101-11 Rev
TSB: When servicing interior electrical switches and components, please note the precautions in this bulletin to avoid damaging electrical components and switches. Many lubricants, cleaners, and automotive chemicals contain silicone or other compounds that may contaminate electrical contacts, and therefore increase electrical resistance and decrease switch performance. The use of any cleaners or fluids may increase the risk of further damage to electrical components.
T-TT-0262-13 Rev
TT: Starting with 2010 Model Year, Toyota began a gradual transition to the use of synthetic 0w-20 viscosity engine oil. There are multiple benefits of this oil. Due to the them improved performance and durability of 0w-20 synthetic oil, Toyota has extended the oil change intervals to 10,000 miles for most vehicles that require this oil.
TTT-0337-15 Rev1
TT: When updating either the navigation or radio firmware, verify the vehicle applicability BEFORE beginning the update.
T-TT-0268-13 Rev
TT: Some customers may encounter Bluetooth® connectivity concerns such as: * Difficulty to pair the phone. * Intermittent Bluetooth® failure to connect to the vehicle when first turning on the vehicle. * Various Bluetooth® Audio functions are no longer functioning with customer's phone such as ability to change the track using the steering wheel controls. These concerns can be caused by changes made on the customer's phone. Make sure to inquire with the customer if the connectivity concerns occurred after receiving an operating system update on their phone or if they have restored their phone data/settings recently.
T-SB-0040-08
TSB: On some vehicles, when Rapgard is removed, the paint may have a stained appearance. These stains appear to be under the clear coat (repainting this area is not necessary). The stain patterns are usually under wrinkles in the Rapgard. These wrinkles sometimes trap water and cause the paint to stain from the trapped moisture, especially on horizontal surfaces, such as the hood, roof, and trunk. Stains can be removed by heating the stained surface to remove the trapped moisture.
TT-0307-14 Rev2
TT: Some customers may encounter various Bluetooth connectivity concerns after upgrading to iOS 8.0 and later. Conditions typically experienced include inability to pair the iPhone to the system, poor sound quality during phone calls placed through the audio/navigation system, and the inability to place a hands free phone call using the audio/navigation system.
T-TT-0267-13 Rev
TT: Some vehicles equipped with Display Audio may exhibit a condition where the touch screen is inoperative.
TC15-004
TOYOTA 2012-2013 MODEL YEAR CAMRY, HYBRID, PRIUS C & YARIS VEHICLES: THIS TSB CONTAINS AN OWNER NOTIFICATION LETTER. SELECT DOCUMENT SEARCH BUTTON BELOW. *LJ
T-SB-0012-13 REV
TSB: FLASH REPROGRAMMING ALLOWS THE ECU SOFTWARE TO BE UPDATED WITHOUT REPLACING THE ECU. FLASH CALIBRATION UPDATES FOR SPECIFIC VEHICLE MODELS/ECUS ARE RELEASED AS FIELD-FIX PROCEDURES DESCRIBED IN INDIVIDUAL SERVICE BULLETINS. THIS BULLETIN DETAILS THE TECHSTREAM ECU FLASH REPROGRAMMING PROCESS AND OUTLINES USE OF THE TECHNICAL INFORMATION SYSTEM (TIS) AND THE CALIBRATION UPDATE WIZARD (CUW). FLASH CALIBRATION UPDATES CAN ONLY BE APPLIED TO THE VEHICLE/ECU COMBINATION FOR WHICH THEY ARE INTENDED. ECUS HAVE INTERNAL SECURITY THAT WILL NOT ALLOW THEM TO BE PROGRAMMED WITH ANOTHER ECUS INFORMATION.
TSB-0012-13 Rev2
TSB: Flash reprogramming allows the ECU software to be updated without replacing the ECU. Flash calibration updates for specific vehicle models/ECUs are released as field-fix procedures described in individual Service Bulletins. This bulletin details the Techstream ECU flash reprogramming process and outlines use of the Technical Information System (TIS) and the Calibration Update Wizard (CUW). Flash calibration updates can only be applied to the vehicle/ECU combination for which they are intended. ECUs have internal security that will not allow them to be programmed with another ECU?s information.
T-TT-307-14 Rev1
TT: Customers complain of various Bluetooth connectivity concerns after upgrading to iOS 8.0 and later. Conditions typically experienced include inability to pair the iPhone to the system, poor sound quality during phone calls placed through the audio/navigation system, and the inability to place a hands free phone call using the audio/navigation system.
T-TT-0174-12
Tech Tip: The purpose for this Tech Tip is to help identify the shift-lock override cover location when performing Pre Delivery Service (PDS). In other models this cover has typically been attached to the shifter in direct view. For Prius C models, the shift-lock override cover is located in the glove box.
T-SB-0006-11 Rev
TSB: World Standard (WS) Automatic Transmission Fluid (ATF) was introduced to reduce maintenance costs and increase the mileage between scheduled maintenance checks. Here are some important tips when working with ATF-WS in Toyota vehicles requiring it's use.
T-TT-0309-14
Tech Tip: Some customers may experience Bluetooth disconnections or loss of SMS Text Message Functionality on the navigation/audio system with Android phones running OS 4.4 or later. Condition tends to occur to customers who have many previous text messages on their phones.
T-TT-0307-14
Tech Tip: Customer complains of carious Bluetooth connectivity concerns after upgrading to iOS 8.0 and later. Conditions typically experienced include inability to pair the iPhone to the system, poor sound quality during phone calls placed through the audio/navigation system, and the inability to place a hands free phone call using the audio/navigation system.
T-TT-0234-13
Tech Tip: Since MY 2011, several different update or upgrade USB SSTs have been issued for Toyota audio and navigation systems.
T-TT-0246-13 Rev
Tech Tip: Tips for writing a DPR (Dealer Product Report) on manufacturing issues for windows and windshields.
T-TT-0294-14
Tech Tip: Greenhouse Gas Logic (GHG) has been implemented on Toyota A/C Systems to reduce tailpipe emissions. The Federal government issues CAFÉ (Corporate Average Fuel Economy) credits to vehicle manufacturers that implement new technologies that reduce the carbon footprint of the vehicles they produce. GHG Logic technology works by automatically operating the HVAC system in REC mode when certain conditions are met, improving the A/C system cooling efficiency and reducing the vehicle's CO2 tailpipe emissions.
T-TT-0010-10 Rev
Tech Tip: Low battery voltage can contribute to a MIL "ON" condition for P0335 (Crankshaft Position Sensor Circuit) and/or P0340 (Camshaft Position Sensor Circuit) due to inconsistent rotational speed of the engine's crankshaft.
T-SB-0033-14
Some vehicles in particular geographic areas may exhibit a condition where the HVAC Evaporator Drain Hose has become obstructed with an insect nest. An insect repellent drain hose tip (ARINIX® Tip) is now available to help minimize future occurrences of this environmental condition. For some models, a new drain hose is required to properly fit the ARINIX® Tip. Follow the procedures in this bulletin for proper handling and installation of this optional service part.
T-SB-0014-14
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
T-TT-0268-13
Customer complains of Bluetooth connectivity concerns such as: Difficulty to pair phone, Intermittent Bluetooth failure to connect to the vehicle when first turning on the vehicle. These concerns can be caused by changes made on the customer's phone. Make sure to inquire with the customer if the connectivity concerns occurred after receiving an operating system update on their phone or they have restored their phone data/settings recently.
T-TT-0262-13
Starting with the 2010 Model Year, Toyota began a gradual transition to the use of synthetic 0w-20 viscosity engine oil. There are multiple benefits of this oil. Due to the improved performance and durability of 0w-20 synthetic oil, Toyota has extended the oil change intervals to 10,000 miles for most vehicle that require this oil.
T-SB-0187-12 Rev
Toyota vehicles are equipped with either conventional or run-flat tires. Sometimes punctures may occur as a result of contact with road debris or other hazards. If a puncture occurs, it may be possible to repair the tire and return it to service. With a conventional tire it is not possible to drive for an extended amount of time with the tire at low pressures as damage to the tire may occur. With run-flat tires, due to reinforced sidewalls, it is possible to drive for up to 100 miles (160 km) at speeds less than 55 mph (90 km/h) with little or no damage to the tire.
T-TT-0213-13
Toyota vehicles are equipped with Supplemental Restraint Systems (SRS), including various airbags and in some models, seat belt pre-tensioners, to help reduce the risk of injury in a collision. If a customer expresses any concerns that the SRS airbags or pre-tensioner devices did not perform as expected (including an unintended deployment event), please follow the steps in the recommendations section below.
T-TT-0278-13
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
T-SB-0185-13
The following procedures are recommended during routine maintenance or in the event of a customer concern for wiper performance.
TS-BO030-01 Obso
This bulletin is now obsolete. Please see T-SB-0185-13.
T-SB-0093-12 Rev
This bulletin is no longer applicable and is now obsolete.
T-SB-0026-12 Rev
This bulletin is now obsolete. Please see T-SB-0163-13 .
T-SB-0163-13
Use the following procedures to check and/or update the software version of Entune/Navigation for Non-HDD Type units.
T-SB-0122-11 Rev
Beginning in 1998, Toyota introduced side airbags as optional equipment. Toyota does NOT recommend replacement of original seat covers with non-Toyota leather or other seat cover materials on vehicles due to the following: Seat covers NOT recommended by Toyota may affect side airbag performance, in general or in part, during an accident. Modifications that negatively affect side airbag performance can result in severe occupant injuries. Seat covers are an integral part of this safety system. Replacing fabric seat covers with non-Toyota leather or other seat cover materials may compromise the effectiveness of this safety system. The design of the seat is complex, integrating safety and strength with comfort and luxury. Toyota strongly discourages modifying original equipment seats that have optional side airbags. Additionally, Toyota strongly advises against the installation or use of aftermarket seat covers, which could impair the performance of the side airbags in the event of an accident.
T-TT-0267-13
Some vehicles equipped with Display Audio may exhibit a condition where the touch screen is inoperative.
T-TT-0269-13
The appearance of spots in tempered glass (when viewed at certain angles) is the result of the heat treating and quick quenching process during manufacturing.
T-TT-0051-10
If a customer states there is an unpleasant odor in the vehicle from the HVAC system, there are various factors that may be involved.
T-TT-0260-13
Customer?s experiencing this condition can use a 3rd party podcast application on their iPhone (such as Pocket Casts or Instances) instead of the native Apple Podcast application.
T-TT-0257-13
iTunes Radio is a new feature for iPhone 4, 4S, 5, 5S, and 5C running iOS 7 or later. This feature does work with the in-vehicle audio system either via Bluetooth or by USB cable. Details on how to access this feature are described below.
T-TT-0256-13
Customers using iPhone 4, 4S, 5, 5S, or 5C running iOS 7.0 or later now have the ability to make Facetime Audio calls (no video). When a customer is paired by Bluetooth Hands Free and they make a Facetime Audio call the vehicle radio will treat it as a typical Bluetooth phone call. Because Facetime works differently than a typical phone call, the in-vehicle experience may not meet the customer?s expectations.
T-TT-0256-13A
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
T-TT-0199-12
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
T-TT-0051-10 Rev
If a customer states there is an unpleasant odor in the vehicle from the HVAC system, there are various factors that may be involved.
T-TT-0250-13 Rev
To receive satellite radio functions after the initial trial period has expired, the customer must enter into a contract with XM Satellite Radio Inc. After entering into a contract, registration of an 8-digit XM Radio ID is required. This 8-digit XM Radio ID is found by turning to channel ?0? of the satellite radio.
T-SB-0142-13
Some 2004 ? 2014 model year Toyota vehicles may exhibit odors naturally occurring from the HVAC system and/or related environmental factors. Although there is no way to eliminate these odors, follow the General Procedure in this bulletin to minimize the odors experienced.
T-SB-0141-13
A new Special Service Tool (SST 09709-00002) has been introduced to aid in the inspection procedure for certain vehicles equipped with a floor pedal-type parking brake system. This bulletin references the correct method for installing the Brake Pedal Force Gauge. Refer to the appropriate Repair Manual for parking brake pedal travel inspection and adjustment specification.
T-SB-0247-12 Rev
Some 2012 ? 2013 model year Camry, Venza, and 2013 model year Avalon and Sienna vehicles equipped with 2GR-FE engines may exhibit a MIL ?ON? condition with Diagnostic Trouble Code (DTC) P219A or P219B present. The Engine Control Module/ECM (SAE term: Powertrain Control Module/PCM) logic has been modified to reduce the possibility of this condition occurring. Please follow the repair procedure below to address this condition.
T-TT-0250-13
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
T-TT-0240-13 R1
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
T-TT-0005-10
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
T-TT-0246-13
Tips for writing a DPR (Dealer Product Report) on manufacturing issues for windows and windshields.
T-SB-0083-13
The procedure in this bulletin is a general guideline on how to properly diagnose the air conditioning system after a component failure. Refer to the applicable Repair Manual for vehicle specific repair procedures and parts.
T-SB-0079-13
Some 2012 ? 2013 model year Prius C vehicles may exhibit a condition where a piece of foam that fits between the instrument panel and the windshield may come loose. Parts have been revised to address this condition.
T-SB-0076-13
Some 2012 model year Prius C vehicles may exhibit a ticking noise coming from the glove box when driving over rough roads. The glove compartment has been revised to address this condition.
T-SB-0076-13A
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
T-SB-0075-13
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
T-TT-0124-11
Please refer to the following recommendations for the best practices for vehicle tire rotations.
T-TT-0128-11
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
T-TT-0240-13
When diagnosing audio, navigation, and Bluetooth concerns on Toyota vehicles equipped with Premium Display Audio with Entune, adhere to the guidelines listed below.
T-SB-0059-13
On start-up, some vehicles may exhibit a condition where the A/C system blows warm air and Diagnostic Trouble Code (DTC) B1476 is set. An updated A/C compressor is available to address this condition.
T-PG006-00 Obsol
This bulletin is now obsolete. Please see T-SB-0054-13.
T-SB-0054-13
California (CA), Federal (FED), and 50 State Certified emission control underhood labels (emission labels) may be obtained through your dealership?s Parts Department utilizing standard replacement parts ordering procedures. Follow the guidelines outlined in this bulletin to ensure proper label application.
T-TT-0118-11 Rev
Technicians should confirm the following key points to minimize the potential for future MIL "ON" concerns after HV battery replacement.
T-TT-0232-13
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
T-TT-0232-13 Rev
Some customers may notice a brightness difference between audio screen and Map/APPs/Phone screen on Display Audio w/Navigation head units. This brightness difference may occur whenever the battery is disconnected or when the radio is new/replaced.
T-SB-0141-10 Rev
If a creak, tick, or rattle noise is heard at the top or bottom of the windshield, or at the top of the rear glass, the source of the noise may be the two stoppers bonded to the top of the windshield/rear glass, or the windshield retainers bonded to the lower edge of the windshield. This bulletin provides the recommended repair procedure to eliminate these types of noises from the windshield/rear glass area.
T-SB-0030-12 Rev
This bulletin is now obsolete. Please see T-SB-0051-13.
T-SB-0051-13
2012-2013 model year vehicles equipped with a Display Audio Navigation System and Entune (version less than 2.2.0) may exhibit one or more of the following conditions.
T-TT-0226-13
The customer is having difficulty changing the multi-display screen from Day Mode. If the multi-display screen is set to Day Mode when the headlights are on, the setting we be memorized when the engine is turned off.
T-SB-0035-13
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
T-TT-0222-13
The vehicle will not start or ready-on and the steering wheel lock is engaged so that the steering wheel may only be turned very little from side-to-side.
T-SB-0033-13
Some customers may inquire about the frequency and power output of the Smart Key/Smart Entry systems used on various models. The Smart Key/Smart Entry systems conform to all applicable FCC rules. This bulletin details the applicable specifications for these systems.
T-SB-0018-13
Some 2012 model year Prius C vehicles may exhibit one or more of the following conditions: ABS and TRC MIL ?ON? with DTC B2321. Keyless Entry and Smart Key features are inoperative. Vehicle interior door lock/unlock switches are inoperative. Multi-Display may show the incorrect door is opened. Shift Position Linked Door Locking Function may not operate, not locking the doors when the shift position is moved out of ?P? position. If any of these conditions are exhibited and the vehicle is able to ?Ready? On (key may need to be held over the ignition button), the Main Body ECU may require replacement.
T-SB-0012-13
Flash reprogramming allows the ECU software to be updated without replacing the ECU. Flash calibration updates for specific vehicle models/ECUs are released as field-fix procedures described in individual Service Bulletins. This bulletin details the Techstream ECU flash reprogramming process and outlines use of the TIS and the CUW.
T-SB-0064-10 Rev
This bulletin is now obsolete. Please see T-SB-0012-13.
T-SB-0007-13 R1
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
T-SB-0005-13
Toyota models equipped with the display Audio HDD Navigation System Require a Special Service Tool (SST) USB drive to update the map, points of interest, Gracenote, and system software. The SST is used with all vehicles to deliver the update, however a unique Activation Number is required for each vehicle. Activation numbers are provided in an ACN pamphlet available through the normal parts ordering system.
T-SB-0006-13
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
T-TT-0005-10 Rev
Starting with the 2010 MY, Toyota began a gradual transition to the use of synthetic 0w-20 viscosity engine oil.
T-TT-0204-12
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
T-TT-0205-12
Customers who purchase new or replacement iPhones running iOS 6 may find that Toyota a Entune application will not launch on the iPhone. The issue can occur when the customer restores/transfers their apps, contacts, etc.
T-SB-0187-12
Toyota vehicles are equipped with either conventional or run-flat tires. Sometimes punctures may occur as a result of contact with road debris or other hazards. If a puncture occurs, it may be possible to repair the tire and return it to service. With a conventional tire it is not possible to drive for an extended amount of time with the tire at low pressures as damage to the tire may occur. With run-flat tires, due to reinforced sidewalls, it is possible to drive for up to 100 miles (160 km) at speeds less than 55 mph (90 km/h) with little or no damage to the tire.
T-SB-0103-12 R1
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
T-SB-0093-12
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
T-SB-0060-12
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
T-SB-0026-12
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
T-PG007-01
Replacement vin plates.
T-PG002-91
Product general information.
Complaint counts are reports filed with NHTSA, not failure rates. A common model collects more of them than a rare one that breaks more often.