Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
T-SB-0055-24 Rev2
Service Bulletin/Repair Instructions
Some 2005 – 2026 Toyota vehicles that have undergone water intrusion may exhibit a condition in which a musty odor is present. Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this Service Bulletin is to provide general guidelines and procedures for odor remediation. This Service Bulletin provides a guide on how to prepare and treat the interior of the vehicle for odor remediation. Refer to the applicable model and model year Repair Manual and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines.
21TG01
Service Bulletin/Repair Instructions
Campaign Expired - replaced with campaign 23TA13TECHNICAL INSTRUCTIONS FOR CONSUMER ADVISORY 21TG01 12-VOLT BATTERY SIZE AND INSTALLATION INSPECTION CERTAIN 2013 – 2018 RAV4
T-SB-0058-23 Rev1
Service Campaign
The air conditioning dye injection tool kit has been developed to aid in identifying the location of air conditioning refrigerant leaks. The procedures outlined in this Service Bulletin aid in locating, inspecting, and repairing refrigerant leaks.
T-SB-0035-24 Rev2
Service Bulletin/Repair Instructions
Acid rain results from rainwater or other airborne moisture that become acidic due to industrial chemical impurities in the atmosphere. If these acidic compounds settle on an exposed vehicle, especially the horizontal areas such as the hood, roof, and decklid, significant damage to the painted surfaces can occur. Acid rain damage can typically be identified on vehicles by the presence of stains on the paint surface that resemble hard water spots. Unlike water spots however, acid rain damage cannot be removed by regular washing procedures. Also, because acid rain can etch and soften the paint, normal buffing or polishing repair procedures should not be attempted. This can cause further damage and result in visible depressions in the paint surface. The following are the three major categories of acid rain damage: •Minor damage: requires only buffing to repair. •Moderate damage: usually requires neutralizing, color sanding, and buffing. •Severe damage: extending beyond 1/2 mil of clearcoat on a pearl, metallic, or solid color, requires neutralization, sanding, and repainting. In cases where acid rain damage is minor, neutralization and buffing with a liquid-type paint finessing product may provide an adequate repair. Only specially formulated products outlined in this bulletin should be used for that purpose. Unfortunately, other than minor damage, there is no simple method of determining the actual extent (depth) of acid penetration other than color sanding a representative affected area until there is no visible etching or depressions, followed by measuring the amount of paint removed with either a magnetic or digital-type film thickness gauge. The procedures in this bulletin are intended for use by qualified body/paint technicians and should not be attempted by inexperienced personnel. It is the dealer’s responsibility to protect and maintain the quality of the vehicle’s paint finish after receipt at the dealership prior to the first sale. Perform frequent vehicle washing, as often as daily, during high heat and humidity periods to minimize the potential for paint damage due to acid rain exposure. This is especially important in geographical areas known for high frequency and concentration of acid rain and industrial fallout.
T-SB-0038-24 Rev2
Service Bulletin/Repair Instructions
To prevent brake rotor rust from forming during transportation and storage, wheel film will be used instead of a cardboard type of anti-rust cover. The purpose of the wheel film is to shield the disc brake rotor from weather elements and initial rust before the vehicle is delivered to the customer. Consequently, the film should remain on the wheel for as long as possible.
T-SB-0039-24 Rev2
Service Bulletin/Repair Instructions
The condition known as acid rain is caused by airborne chemicals or particles in the atmosphere, which mix with rainwater, nighttime dew, or high humidity to form acidic compounds. If these contaminants settle and remain on a painted vehicle surface, especially the horizonal areas of the hood, roof, and decklid, significant damage can occur. This damage is the result of actual etching of the paint and appears as pitting or water spots. As acid rain droplets on the vehicle surface evaporate, the concentration strength of the acid increases, causing deeper and more rapid damage. This evaporation and corrosive action also occur more rapidly on dark colored cars as direct sun heat increases. It is the dealer’s responsibility to protect and maintain the quality of the vehicle’s paint finish after receipt at the dealership prior to the first sale. In areas known for high frequency and/or concentration of acid rain, frequent vehicle washing during high heat or humidity periods will minimize the potential for paint damage caused by acid rain. It is further recommended that either reverse osmosis or deionized water be used to prevent water spotting.
T-SB-0061-23 Rev2
Service Bulletin/Repair Instructions
Toyota vehicles are currently protected with RapgardTM protective film designed to protect the horizontal painted surfaces. This material protects from acid rain, environmental fallout, and rail contamination. Follow the Removal Procedure in this bulletin to remove the RapgardTM protective film within 90 days from initial application.
T-SB-0062-23 Rev2
Service Bulletin/Repair Instructions
Vehicles may occasionally be subjected to contamination by airborne iron particles shed from railroad tracks, train wheels, exposure to heavy machinery facilities, grinding, welding, etc. This type of contamination can be identified by the presence of small, red or brown particles on the paint surface. These particles are often difficult to see on dark color paints but can be easily felt when brushing a hand across horizontal body surfaces such as the hood, roof, or deck lid. Follow the Repair Procedure in this bulletin to clean vehicles that may have been subjected to contamination by airborne iron particles such as rail dust during rail transportation or extended storage near industrial areas.
T-SB-0055-24 Rev1
Service Bulletin/Repair Instructions
Some 2005 – 2024 Toyota vehicles that have undergone water intrusion may exhibit a condition in which a musty odor is present. Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this Service Bulletin is to provide general guidelines and procedures for odor remediation. This Service Bulletin provides a guide on how to prepare and treat the interior of the vehicle for odor remediation. Refer to the applicable model and model year Repair Manual and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines. This Service Bulletin is to provide a general overview and direction for the odor remediation process.
T-SB-0035-24 Rev1
Service Bulletin/Repair Instructions
Acid rain results from rainwater or other airborne moisture that become acidic due to industrial chemical impurities in the atmosphere. If these acidic compounds settle on an exposed vehicle, especially the horizontal areas such as the hood, roof, and decklid, significant damage to the painted surfaces can occur. Acid rain damage can typically be identified on vehicles by the presence of stains on the paint surface that resemble hard water spots. Unlike water spots however, acid rain damage cannot be removed by regular washing procedures. Also, because acid rain can etch and soften the paint, normal buffing or polishing repair procedures should not be attempted. This can cause further damage and result in visible depressions in the paint surface. The following are the three major categories of acid rain damage: •Minor damage: requires only buffing to repair. •Moderate damage: usually requires neutralizing, color sanding, and buffing. •Severe damage: extending beyond 1/2 mil of clearcoat on a pearl, metallic, or solid color, requires neutralization, sanding, and repainting. In cases where acid rain damage is minor, neutralization and buffing with a liquid-type paint finessing product may provide an adequate repair. Only specially formulated products outlined in this bulletin should be used for that purpose. Unfortunately, other than minor damage, there is no simple method of determining the actual extent (depth) of acid penetration other than color sanding a representative affected area until there is no visible etching or depressions, followed by measuring the amount of paint removed with either a magnetic or digital-type film thickness gauge. The procedures in this bulletin are intended for use by qualified body/paint technicians and should not be attempted by inexperienced personnel. It is the dealer’s responsibility to protect and maintain the quality of the vehicle’s paint finish after receipt at the dealership prior to the first sale. Perform frequent vehicle washing, as often as daily, during high heat and humidity periods to minimize the potential for paint damage due to acid rain exposure. This is especially important in geographical areas known for high frequency and concentration of acid rain and industrial fallout.
T-SB-0038-24 Rev1
Service Bulletin/Repair Instructions
To prevent brake rotor rust from forming during transportation and storage, wheel film will be used instead of a cardboard type of anti-rust cover. The purpose of the wheel film is to shield the disc brake rotor from weather elements and initial rust before the vehicle is delivered to the customer. Consequently, the film should remain on the wheel for as long as possible.
T-SB-0039-24 Rev1
Service Bulletin/Repair Instructions
The condition known as acid rain is caused by airborne chemicals or particles in the atmosphere, which mix with rainwater, nighttime dew, or high humidity to form acidic compounds. If these contaminants settle and remain on a painted vehicle surface, especially the horizonal areas of the hood, roof, and decklid, significant damage can occur. This damage is the result of actual etching of the paint and appears as pitting or water spots. As acid rain droplets on the vehicle surface evaporate, the concentration strength of the acid increases, causing deeper and more rapid damage. This evaporation and corrosive action also occur more rapidly on dark colored cars as direct sun heat increases. It is the dealer’s responsibility to protect and maintain the quality of the vehicle’s paint finish after receipt at the dealership prior to the first sale. In areas known for high frequency and/or concentration of acid rain (see Figure 1), frequent vehicle washing during high heat or humidity periods will minimize the potential for paint damage caused by acid rain. It is further recommended that either reverse osmosis or deionized water be used to prevent water spotting.
24TE03
Service Bulletin/Repair Instructions
TECHNICAL INSTRUCTIONS FOR CONSUMER ADVISORY 24TE03 Rav4 Battery Class Action Settlement CERTAIN 2013 – 2018 Model Year RAV4
T-SB-0055-24
Service Bulletin/Repair Instructions
Some 2005 – 2024 Toyota vehicles that have undergone water intrusion may exhibit a condition in which a musty odor is present. Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this Service Bulletin is to provide general guidelines and procedures for odor remediation. This Service Bulletin provides a guide on how to prepare and treat the interior of the vehicle for odor remediation. Refer to the applicable model and model year Repair Manual and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines.
T-SB-0103-20 Rev1
Service Bulletin/Repair Instructions
This Service Bulletin provides updated non-electric water pump leak inspection and diagnostic tips for some 2008 – 2025 model year Toyota vehicles.
Toyota Renotification DL
Other
Safety Recall and Service Campaign completion is an important part of our commitment to customer satisfaction of Toyota products. Toyota will be conducting follow-up notifications to remind owners whose vehicles have not yet had Safety Recall and/or Service Campaign repairs completed in the campaigns listed
Toyota Renotification RL
Other
Toyota plans to conduct Safety Recall and Service Campaign follow-up notifications to owners whose vehicles have not yet had the following Safety Recall and/or Service Campaign repairs completed
T-SB-0061-23 Rev1
Service Bulletin/Repair Instructions
Toyota vehicles are currently protected with RapgardTM protective film designed to protect the horizontal painted surfaces. This material protects from acid rain, environmental fallout, and rail contamination.
T-SB-0062-23 Rev1
Service Bulletin/Repair Instructions
Vehicles may occasionally be subjected to contamination by airborne iron particles shed from railroad tracks, train wheels, exposure to heavy machinery facilities, grinding, welding, etc. This type of contamination can be identified by the presence of small, red or brown particles on the paint surface. These particles are often difficult to see on dark color paints but can be easily felt when brushing a hand across horizontal body surfaces such as the hood, roof, or deck lid.
T-SB-0035-24
Service Bulletin/Repair Instructions
Acid rain results from rainwater or other airborne moisture that become acidic due to industrial chemical impurities in the atmosphere. If these acidic compounds settle on an exposed vehicle, especially the horizontal areas such as the hood, roof, and decklid, significant damage to the painted surfaces can occur. Acid rain damage can typically be identified on vehicles by the presence of stains on the paint surface that resemble hard water spots. Unlike water spots however, acid rain damage cannot be removed by regular washing procedures. Also, because acid rain can etch and soften the paint, normal buffing or polishing repair procedures should not be attempted. This can cause further damage and result in visible depressions in the paint surface. The following are the three major categories of acid rain damage: •Minor damage: requires only buffing to repair. •Moderate damage: usually requires neutralizing, color sanding, and buffing. •Severe damage: extending beyond 1/2 mil of clearcoat on a pearl, metallic, or solid color, requires neutralization, sanding, and repainting. In cases where acid rain damage is minor, neutralization and buffing with a liquid-type paint finessing product may provide an adequate repair. Only specially formulated products outlined in this bulletin should be used for that purpose. Unfortunately, other than minor damage, there is no simple method of determining the actual extent (depth) of acid penetration other than color sanding a representative affected area until there is no visible etching or depressions, followed by measuring the amount of paint removed with either a magnetic or digital-type film thickness gauge. The procedures in this bulletin are intended for use by qualified body/paint technicians and should not be attempted by inexperienced personnel. While the quality and durability of paint on Toyota vehicles is continuously being improved, it remains the dealer’s responsibility to protect and maintain the quality of the vehicle’s paint finish after receipt at the dealership prior to the first sale. To read, While the quality and durability of paint on Toyota vehicles is continuously being improved, it remains the dealer’s responsibility to protect and maintain the quality of the vehicle’s paint finish after receipt at the dealership prior to first sale. Perform frequent vehicle washing, as often as daily, during high heat and humidity periods to minimize the potential for paint damage due to acid rain exposure. This is especially important in geographical areas known for high frequency and concentration of acid rain and industrial fallout.
T-SB-0038-24
Service Bulletin/Repair Instructions
To prevent brake rotor rust from forming during transportation and storage, wheel film will be used instead of a cardboard type of anti-rust cover. The purpose of the wheel film is to shield the disc brake rotor from weather elements and initial rust before the vehicle is delivered to the customer. Consequently, the film should remain on the wheel for as long as possible. SUPERSESSION NOTICE The information contained in this bulletin supersedes Service Bulletin No. PD017-04. •The entire bulletin has been updated.
T-SB-0039-24
Service Bulletin/Repair Instructions
The condition known as acid rain is caused by airborne chemicals or particles in the atmosphere, which mix with rainwater, nighttime dew, or high humidity to form acidic compounds. If these contaminants settle and remain on a painted vehicle surface, especially the horizonal areas of the hood, roof, and decklid, significant damage can occur. This damage is the result of actual etching of the paint and appears as pitting or water spots. As acid rain droplets on the vehicle surface evaporate, the concentration strength of the acid increases, causing deeper and more rapid damage. This evaporation and corrosive action also occur more rapidly on dark colored cars as direct sun heat increases. While Toyota paint quality, durability, and resistance to environmental factors is continuously being improved, it remains the responsibility of the dealer to protect and maintain the vehicle’s paint finish from the time of arrival at the dealership until retail delivery to the customer. In areas known for high frequency and/or concentration of acid rain (see Figure 1), frequent vehicle washing during high heat or humidity periods will minimize the potential for paint damage caused by acid rain. It is further recommended that either reverse osmosis or deionized water be used to prevent water spotting.
T-PANT-2024-004-
Service Bulletin/Repair Instructions
This is to advise of various price adjustments that will affect Toyota Genuine Motor Oil and Long Life Coolant, effective March 1, 2024. These products are ordered through the Toyota Complete Maintenance Care (TCMC) website.
TSB005823
Service Bulletin/Repair Instructions
TSB: The air conditioning dye injection tool kit has been developed to aid in identifying the location of air conditioning refrigerant leaks. Follow the procedures outlined in this service bulletin to aid in locating, inspecting, and repairing refrigerant leaks
TSB003220
Service Bulletin/Repair Instructions
TSB: Replacement certification labels (the vinyl label installed on the driver door or door post) and VIN plates (the metal plate riveted to dashboard) (see Figure 1) for most 1979 ? 2023 model year vehicles may be available provided the requests meet the criteria listed in this Service Bulletin. Follow the Procurement Procedure in this bulletin to request a replacement certification label or VIN plate.
T-SB-0057-18
Service Bulletin/Repair Instructions
TSB: The Immobilizer and Smart Key Reset is a feature that allows the registration of new keys when all master keys are lost. Once the system is reset, all previously registered keys will be erased. Follow the procedures in this bulletin to reset a vehicle Immobilizer or Smart Key system.
Z2G_Dealer_Lette
Service Bulletin/Repair Instructions
DL: Toyota has received reports of paint peeling on certain vehicles with the original factory-applied Blizzard Pearl or Super White paint colors. These reports indicate that vehicles with these specific paint colors, applied during the vehicle manufacturing process, may experience paint peeling on exterior metal body panels. Although the original factory paint is covered by Toyota?s New Vehicle Limited Warranty for 3 years or 36,000 miles (whichever comes first), we at Toyota care about the customers? ownership experience. Toyota is providing coverage for repairs related to the condition described above. The following information is provided to inform you and your staff of the program notification schedule and your degree of involvement.
Z3G_Dealer_Lette
Service Bulletin/Repair Instructions
DL: Toyota has received reports of paint peeling on certain vehicles with the original factory-applied Blizzard Pearl or Super White paint colors. These reports indicate that vehicles with these specific paint colors, applied during the vehicle manufacturing process, may experience paint peeling on exterior metal body panels. Although the original factory paint is covered by Toyota?s New Vehicle Limited Warranty for 3 years or 36,000 miles (whichever comes first), we at Toyota care about the customers? ownership experience. Toyota is providing coverage for repairs related to the condition described above. The following information is provided to inform you and your staff of the program notification schedule and your degree of involvement.
ZKG_Dealer_Lette
Service Bulletin/Repair Instructions
DL: Toyota has received reports of paint peeling on certain vehicles with the original factory-applied Blizzard Pearl or Super White paint colors. These reports indicate that vehicles with these specific paint colors, applied during the vehicle manufacturing process, may experience paint peeling on exterior metal body panels. Although the original factory paint is covered by Toyota?s New Vehicle Limited Warranty for 3 years or 36,000 miles (whichever comes first), we at Toyota care about the customers? ownership experience. Toyota is providing coverage for repairs related to the condition described above. The following information is provided to inform you and your staff of the program notification schedule and your degree of involvement
T-SB-0094-21 Rev
Service Bulletin/Repair Instructions
TSB: Some 2005 ? 2022 model year Toyota vehicles that have undergone water intrusion may exhibit a condition in which a musty smell is present. Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this service bulletin is to provide general guidelines and procedures for odor remediation. This service bulletin provides a guide on how to prepare the interior of the vehicle prior to an odor remediation being performed, as well as contact information for an approved vendor who will arrange the remediation, and instructions on how to prepare the interior of the vehicle for reassembly once the remediation has been completed. Refer to all model and model year specific Repair Manuals and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines. This service bulletin is to provide a general overview and direction for the odor remediation process.
TSB001221Rev2
Service Bulletin/Repair Instructions
TSB: Some 2010 ? 2022 model year Toyota vehicles may exhibit paint stains after the removal of Rapgard?. The paint stains may appear to be under the clear coat but are usually under wrinkles in the Rapgard?. The wrinkles may trap water and cause the paint to stain from the trapped moisture, especially on horizontal surfaces such as the hood, roof, and trunk. Follow the Repair Procedure in this bulletin to address this condition
TSB009421Rev1
Service Bulletin/Repair Instructions
TSB: Some 2005 ? 2022 model year Toyota vehicles that have undergone water intrusion may exhibit a condition in which a musty smell is present. Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this service bulletin is to provide general guidelines and procedures for odor remediation. This service bulletin provides a guide on how to prepare the interior of the vehicle prior to an odor remediation being performed, as well as contact information for an approved vendor who will arrange the remediation, and instructions on how to prepare the interior of the vehicle for reassembly once the remediation has been completed. Refer to all model and model year specific Repair Manuals and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines. This service bulletin is to provide a general overview and direction for the odor remediation process
Support Program
Service Bulletin/Repair Instructions
DL: Toyota has received reports of paint peeling on certain vehicles with the original factory-applied Blizzard Pearl or Super White paint colors. These reports indicate that vehicles with these specific paint colors, applied during the vehicle manufacturing process, may experience paint peeling on exterior metal body panels. Although the original factory paint is covered by Toyota?s New Vehicle Limited Warranty for 3 years or 36,000 miles (whichever comes first), we at Toyota care about the customers? ownership experience. Toyota is providing coverage for repairs related to the condition described above. The following information is provided to inform you and your staff of the program notification schedule and your degree of involvement
ZKG_Paint_Repair
Service Bulletin/Repair Instructions
CSP: Customer Support Program ZKG - Paint Repair Process Operation Flow Chart
TTT063620
Service Bulletin/Repair Instructions
TT: Some Toyota vehicles installed with Toyota Complete Maintenance Care (TCMC) brake pads may exhibit a groan or squeak noise in various driving conditions
21TG01 Dealer Le
Service Bulletin/Repair Instructions
DL: During a recent investigation of reported battery fires in 2013-2018 RAV4 vehicles with gasoline engines (excluding hybrid models), Toyota discovered that many non-Toyota retailers and others who sell or install replacement batteries were recommending a small size battery for replacement. Toyota specifies a particular size replacement battery for the RAV4 that does not include this small size. The smaller battery may not fit securely with the RAV4?s battery mounting parts, and, in some cases, can move around when the vehicle is driven, causing a short circuit. Using the wrong size battery, or not installing a replacement battery properly, can cause damage to the battery and the vehicle, and it could cause a vehicle fire.
T-SB-0012-21 Rev
Service Bulletin/Repair Instructions
TSB: Some 2010 ? 2022 model year Toyota vehicles may exhibit paint stains after the removal of Rapgard?. The paint stains may appear to be under the clear coat but are usually under wrinkles in the Rapgard?. The wrinkles may trap water and cause the paint to stain from the trapped moisture, especially on horizontal surfaces such as the hood, roof, and trunk. Follow the Repair Procedure in this bulletin to address this condition
21TG01 Technical
Service Bulletin/Repair Instructions
TI: TECHNICAL INSTRUCTIONS FOR CONSUMER ADVISORY 21TG01 12-VOLT BATTERY SIZE AND INSTALLATION INSPECTION CERTAIN 2013 ? 2018 RAV4
T-SB-0094-21
Service Bulletin/Repair Instructions
TSB: Some 2005 ? 2022 model year Toyota vehicles that have undergone water intrusion may exhibit a condition in which a musty smell is present. Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this service bulletin is to provide general guidelines and procedures for odor remediation. This service bulletin provides a guide on how to prepare the interior of the vehicle prior to an odor remediation being performed, as well as contact information for an approved vendor who will arrange the remediation, and instructions on how to prepare the interior of the vehicle for reassembly once the remediation has been completed. Refer to all model and model year specific Repair Manuals and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines. This service bulletin is to provide a general overview and direction for the odor remediation process.
21TG01_Dealer_Da
Service Bulletin/Repair Instructions
DD: 21TG01_Dealer_Daily_Message
21TG01 Battery S
Service Bulletin/Repair Instructions
CONSUMER ADVISORY 21TG01 12-VOLT BATTERY SIZE/INSTALLATION CONDITION DISCLOSURE FORM
21TG01 Region Le
Service Bulletin/Repair Instructions
RL: During a recent investigation of reported battery fires in 2013-2018 RAV4 vehicles with gasoline engines (excluding hybrid models), Toyota discovered that many non-Toyota retailers and others who sell or install replacement batteries were recommending a small size battery for replacement. Toyota specifies a particular size replacement battery for the RAV4 that does not include this small size. The smaller battery may not fit securely with the RAV4?s battery mounting parts, and, in some cases, can move around when the vehicle is driven, causing a short circuit. Using the wrong size battery, or not installing a replacement battery properly, can cause damage to the battery and the vehicle, and it could cause a vehicle fire.
21TG01 TI Publis
Service Bulletin/Repair Instructions
TI: TECHNICAL INSTRUCTIONS FOR CONSUMER ADVISORY 21TG01 12-VOLT BATTERY SIZE AND INSTALLATION INSPECTION CERTAIN 2013 ? 2018 RAV4
ZKG Important Up
Service Bulletin/Repair Instructions
DL: CUSTOMER SUPPORT PROGRAM ZKG Multiple Models and Model Years Vehicles Painted with Blizzard Pearl (070) or Super White (040) Paint Color Coverage for Peeling of Factory-Applied Paint
T-TT-0578-19 Rev
Service Bulletin/Repair Instructions
TT: Some customers may encounter Bluetooth® connectivity concerns such as: ?Difficulty to pair the phone. ?Intermittent Bluetooth® failure to connect to the vehicle when first turning on the vehicle. ?Various Bluetooth® Audio functions are no longer functioning with customer?s phone such as ability to change the track using the steering wheel controls. These concerns can be caused by changes made on the customer?s phone. Make sure to inquire with the customer if the connectivity concerns occurred after receiving an operating system update on their phone, or if they have restored their phone data/settings recently.
T-TT-0663-21
Service Bulletin/Repair Instructions
TT: When used in conjunction with the Repair Manual, these Blind Spot Monitor, Forward Recognition Camera, and Front Millimeter Wave Radar tips leverage SSTs and readily available tools to support target placement in varying shop environments.
T-SB-0080-19 Rev
Service Bulletin/Repair Instructions
TSB: Some 2006 ? 2022 model year Toyota vehicles in particular geographic areas may exhibit a condition where the HVAC evaporator drain hose has become obstructed with an insect nest. An insect repellent drain hose tip (ARINIX® Tip) is available to help minimize future occurrences of this environmental condition. For some models, a new drain hose is required to properly fit the ARINIX® Tip. Follow the procedures in this bulletin for proper handling and installation of this optional service part.
T-TT-0659-21 Rev
Service Bulletin/Repair Instructions
TT: Some 2014-2021 model year vehicles equipped with Dynamic Torque Control AWD system may experience a ?Noise? or ?Abnormal Operation? condition from the rear differential front coupling. In some cases, even an ?AWD System Message? with or without a DTC may be present with or without other conditions present.
Toyota PRO21-UFR
Service Bulletin/Repair Instructions
UPDATES TO THE 2014-2021 TOYOTA UNIVERSAL FLAT RATE MANUAL
T-SB-0044-16 Obs
Service Bulletin/Repair Instructions
OBSOLETE NOTICE March 08, 2021: This bulletin is now obsolete. Please see T-SB-0012-21.
Toyota Safety Re
Service Bulletin/Repair Instructions
Toyota Safety Recall and Service Campaign - Technician Certification Requirements
T-TT-0636-20 Rev
Service Bulletin/Repair Instructions
TT: Some Toyota vehicles installed with Toyota Complete Maintenance Care (TCMC) brake pads may exhibit a groan or squeak noise in various driving conditions.
T-SB-0012-21
Service Bulletin/Repair Instructions
TSB: Some 2010 ? 2021 model year Toyota vehicles may exhibit paint stains after the removal of Rapgard?. The paint stains may appear to be under the clear coat but are usually under wrinkles in the Rapgard?. The wrinkles may trap water and cause the paint to stain from the trapped moisture, especially on horizontal surfaces such as the hood, roof, and trunk. Follow the Repair Procedure in this bulletin to address this condition.
Dealer Daily Mes
Service Bulletin/Repair Instructions
DD: On 2/25/2021, NHTSA opened an investigation into certain RAV4 vehicles related to the 12V battery.
T-SB-0032-20 Rev
Service Bulletin/Repair Instructions
TSB: Replacement certification labels (the vinyl label installed on the driver door or door post) and VIN plates (the metal plate riveted to dashboard) (see Figure 1) for most 1979 ? 2021 model year vehicles may be available provided the requests meet the criteria listed in this Service Bulletin. Follow the Procurement Procedure in this bulletin to request a replacement certification label or VIN plate.
T-TT-0636-20
Service Bulletin/Repair Instructions
TT: Some Toyota vehicles installed with Toyota Complete Maintenance Care (TCMC) brake pads may exhibit a groan or squeak noise in various driving conditions.
T-TT-0628-20
Service Bulletin/Repair Instructions
TT: HVAC drain tube is found to be blocked/clogged.
ZKG_Proper_Photo
Service Bulletin/Repair Instructions
ZKG WEBSITE PROPER PHOTOGRAPH SUBMISSION
T-TT-0468-17 Rev
Service Bulletin/Repair Instructions
TT: HVAC drain tube is found to be blocked/clogged.
T-TT-0553-19 Rev
Service Bulletin/Repair Instructions
TT: The new DCA-8000 Diagnostic Charger may cause your facility?s Ground Fault Circuit Interrupter (GFCI) breaker to trip. A GFCI breaker can be tripped for various reasons, one of the reasons may be related to the DCA-8000. We are investigating this issue to determine the root cause. Other reasons the GFCI breaker may trip ?Circuit demand is too high for GFCI rating ?Worn out GFCI internal contacts ?Improper installation or wiring of GFCI breaker
ZKG_Technical_In
Service Bulletin/Repair Instructions
TI: TECHNICAL INSTRUCTIONS Customer Support Program ZKG Multiple Models and Model Years Vehicles Painted with Blizzard Pearl (070) or Super White (040) Paint Color Coverage for Peeling of Factory-Applied Paint
T-TT-0537-19_Rev
Service Bulletin/Repair Instructions
TT: The blind spot monitor (BSM) sensor angle inspection is used to confirm that the BSM sensor is within the specified angle before performing axis beam adjustment. When used in conjunction with the repair manual, these BSM tips leverage SSTs and readily available tools to support sensor angle confirmation in varying shop environments.
T-SB-0304-17 Obs
Service Bulletin/Repair Instructions
TSB: OBSOLETE NOTICE April 07, 2020: This bulletin is now obsolete. Please see T-SB-0032-20. Replacement Certification Labels and VIN Plates
T-SB-0032-20
Service Bulletin/Repair Instructions
TSB: SUPERSESSION NOTICE The information contained in this bulletin supersedes Service Bulletin Nos. PG021-88, PG015-89, PG0015-90, PG002-91, PG002-93, PG005-97, PG007-01, PG007-07, PG006-01, PG004-97, T-SB-0144-08, and T-SB-0304-17. The aforementioned bulletins are obsolete, and any printed versions should be discarded. Replacement certification labels (the vinyl label installed on the driver door or door post) and VIN plates (the metal plate riveted to dashboard) (see Figure 1) for most 1979 ? 2020 model year vehicles may be available provided the requests meet the criteria listed in this Service Bulletin. Follow the Procurement Procedure in this bulletin to request a replacement certification label or VIN plate.
T-SB-0003-19 Obs
Service Bulletin/Repair Instructions
TSB: OBSOLETE NOTICE March 10, 2020: This bulletin is now obsolete. Please see T-SB-0024-20.
T-SB-0024-20
Service Bulletin/Repair Instructions
TSB: SUPERSESSION NOTICE The information contained in this bulletin supersedes Service Bulletin No. T-SB-0003-19. ?The Introduction and Software Update Information sections have been updated. Service Bulletin No. T-SB-0003-19 is obsolete and any printed versions should be discarded. Some 2016 model year vehicles equipped with Entune? Audio (version UU.11.13), Entune? Audio Plus (version EU.20.21), or Entune? Premium Audio (CU.20.22) or older may exhibit one or more of the following conditions: ?Bluetooth® audio information is missing from instrument cluster MID ?Long street names are not indicated when using turn-by-turn directions ?Abnormal navigation routing ?Toyota Park Assist Settings button displays in the Settings menu ?System is unable to call phone numbers with ?-? present in the number ?System is unable to send SMS via the Quick Message feature ?Abnormal Bluetooth® audio playback when inserting and removing the iPhone® USB cable from the USB port ?System is unable to play audio from iPhone® connected via USB when two phones are connected via Bluetooth® at the same time ?Browse button operates intermittently in Bluetooth® audio ?Screen flickers when switching between day and night modes ?Abnormal Pandora Internet Radio operation when switching between two iPhones ?Unit reboots intermittently ?Diagnostic Trouble Code (DTC) U1110 or B15E6 is present ?Diagnostic screen displays intermittently ?Weather Map is inoperative ??Unable to connect to server? displays when using voice recognition and searching for ?IHOP? ?Panoramic view monitor operates abnormally
T-SB-0142-13_Obs
Service Bulletin/Repair Instructions
OBSOLETE NOTICE February 12, 2020: This bulletin is now obsolete. Please see T-SB-0010-20.
T-SB-0010-20
Service Bulletin/Repair Instructions
TSB: Some 2004 ? 2017 model year Toyota vehicles may exhibit odors naturally occurring from the HVAC system and/or related environmental factors. Although there is no way to eliminate these odors, follow the General Procedure in this bulletin to minimize the odors experienced
T-SB-0008-20
Service Bulletin/Repair Instructions
TSB: Vehicles may display evidence of a fluid leak or fluid seep from powertrain components. This bulletin explains how to determine the differences between a fluid leak versus a fluid seep. Cases that are determined to be a ?leak? should be repaired accordingly and will be covered under warranty if applicable. Cases that are determined to be a ?seep? should be documented on the repair order and inspected at the next service interval. Follow the Repair Information in this bulletin to determine if the concern in question is a fluid leak or fluid seep and review the Repair Procedure section to address the condition. NOTE This bulletin applies to ALL powertrain fluids excluding fuel and coolant.
T-TT-0520-19_Rev
Service Bulletin/Repair Instructions
TT: In certain cases of leaking air conditioning systems, the root cause of the leak is inadvertently overlooked, causing a repeat repair. To improve customer satisfaction and repair A/C system leaks in one dealer visit, Toyota has developed a set of guidelines for evaluating A/C system components.
ZKG_Technical In
Service Bulletin/Repair Instructions
Technical Instructions: December 12, 2019. This document has been updated to clarify that only authorized Toyota dealerships are authorized to confirm if the paint peeling condition is covered by this program. However, after confirming that the paint peeling condition is covered by this program, the authorized Toyota dealership may choose to coordinate to have the repainting repair performed by a non-Toyota repair facility (e.g. third-party collision repair facility, body shop, etc.).
ZKG_Dealer Packa
Service Bulletin/Repair Instructions
Dealer Package: December 12, 2019 This document has been updated to clarify that only authorized Toyota dealerships are authorized to confirm if the paint peeling condition is covered by this program. However, after confirming that the paint peeling condition is covered by this program, the authorized Toyota dealership may choose to coordinate to have the repainting repair performed by a non-Toyota repair facility (e.g. third-party collision repair facility, body shop, etc.).
Customer Support
Service Bulletin/Repair Instructions
Dealer Daily Message: ***Phase 2 ? Customer Renotification and Repair Phase*** Repair is Now Available Multiple Models and Model Years Vehicles Painted with Blizzard Pearl (070) or Super White (040) Paint Color Coverage for Peeling of Factory-Applied Paint. The repair phase of Customer Support Program ZKG is now available. Refer to the Dealer Letter on TIS for additional information.
T-SB-0162-19
Service Bulletin/Repair Instructions
TSB: Some 2008 ? 2019 model year Toyota vehicles painted with either 070 Blizzard Pearl or 040 Super White may exhibit peeling paint on one or more metal body panels. The paint may peel between the primer and E-coat layer, exposing the gray or brownish-green E-coat. The affected panel(s) will require prepping and repainting to address this condition. The paint repair may need to be sublet to a body shop.
ZKG_Dealer Email
Service Bulletin/Repair Instructions
Dealer Email: Toyota has received reports of paint peeling on certain vehicles with the original factory-applied Blizzard Pearl or Super White paint colors. These reports indicate that vehicles with these specific paint colors, applied during the vehicle manufacturing process, may experience paint peeling on exterior metal body panels. Although the original factory paint is covered by Toyota?s New Vehicle Limited Warranty for 3 years or 36,000 miles (whichever comes first), we at Toyota care about the customers? ownership experience. Toyota is providing coverage for repairs related to the condition described above. The following information is provided to inform you and your staff of the program notification schedule and your degree of involvement.
ZKG_Paint Repair
Service Bulletin/Repair Instructions
Repair Process: Customer Support Program ZKG ? Paint Repair Process.
ZKG_Region Email
Service Bulletin/Repair Instructions
Region Email: Toyota has received reports of paint peeling on certain vehicles with the original factory-applied Blizzard Pearl or Super White paint colors. These reports indicate that vehicles with these specific paint colors, applied during the vehicle manufacturing process, may experience paint peeling on exterior metal body panels. Although the original factory paint is covered by Toyota?s New Vehicle Limited Warranty for 3 years or 36,000 miles (whichever comes first), we at Toyota care about the customers? ownership experience. Toyota is providing coverage for repairs related to the condition described above. The following information is provided to inform you and your staff of the program notification schedule and your degree of involvement.
ZKG_Region Lette
Service Bulletin/Repair Instructions
Region Letter: Toyota has received reports of paint peeling on certain vehicles with the original factory-applied Blizzard Pearl or Super White paint colors. These reports indicate that vehicles with these specific paint colors, applied during the vehicle manufacturing process, may experience paint peeling on exterior metal body panels. Although the original factory paint is covered by Toyota?s New Vehicle Limited Warranty for 3 years or 36,000 miles (whichever comes first), we at Toyota care about the customers? ownership experience. Toyota is providing coverage for repairs related to the condition described above.
T-SB-0003-19_Rev
Service Bulletin/Repair Instructions
TSB: REVISION NOTICE November 25, 2019 Rev2: ? Applicability has been updated to include 2019 model year Corolla and Prius C vehicles. ? The faceplate ID applicability table has been updated. October 23, 2019 Rev1: ? The entire bulletin has been updated. Any previous printed versions of this bulletin should be discarded. SUPERSESSION NOTICE The information contained in this bulletin supersedes Service Bulletin No. T-SB-0234-17. ? The Introduction and Software Update Procedure sections have been updated. Service Bulletin No. T-SB-0234-17 is obsolete and any printed versions should be discarded.
T-TT-0578-19
Service Bulletin/Repair Instructions
TT: Some customers may encounter Bluetooth® connectivity concerns such as: ? Difficulty to pair the phone. ? Intermittent Bluetooth® failure to connect to the vehicle when first turning on the vehicle. ? Various Bluetooth® Audio functions are no longer functioning with customer?s phone such as ability to change the track using the steering wheel controls. These concerns can be caused by changes made on the customer?s phone. Make sure to inquire with the customer if the connectivity concerns occurred after receiving an operating system update on their phone, or if they have restored their phone data/settings recently.
T-SB-0025-19_Rev
Service Bulletin/Repair Instructions
TSB: REVISION NOTICE September 26, 2019 Rev1: ? The Warranty Information, Parts Information, and Repair Procedure sections have been updated. Any previous printed versions of this bulletin should be discarded. Some 2009 ? 2018 model year RAV4 and 2017 ? 2018 model year iM vehicles may exhibit a grind/groan noise from the front brake pads. An updated pad kit is now available as a service part. Follow the Repair Procedure in this bulletin to address this condition.
T-TT-0574-19
Service Bulletin/Repair Instructions
TT: Some customers may experience poor outgoing Bluetooth sound quality, this can occur for various reasons. Current multimedia systems are designed with the ability to adjust Bluetooth sound quality to compensate for echo or excessive background noise.
T-TT-0573-19
Service Bulletin/Repair Instructions
TT: Some customers may experience a call failure when attempting to call a conference call number that has been saved in their phonebook (ex: ?8005550122,,,1.,2;;;2#?). This issue is caused by changes to the Bluetooth in the iOS 13 update and may be resolved in a future iOS update.
T-TT-0555-19
Service Bulletin/Repair Instructions
TSB: Some AWD 2014 - 2017 model year Sienna and 2016 - 2018 model year RAV4 customers may experience an abnormal noise from rear coupling unit while driving. This condition can be caused by utilizing an improper towing method when transporting vehicles.
T-TT-0553-19
Service Bulletin/Repair Instructions
TT: The new DCA-8000 Diagnostic Charger may cause your facility?s Ground Fault Circuit Interrupter (GFCI) breaker to trip. A GFCI breaker can be tripped for various reasons, one of the reasons may be related to the DCA-8000. We are investigating this issue to determine the root cause. Other reasons the GFCI breaker may trip ? Circuit demand is too high for GFCI rating ? Worn out GFCI internal contacts ? Improper installation or wiring of GFCI breaker
T-SB-0080-19
Service Bulletin/Repair Instructions
TSB: SUPERSESSION NOTICE The information contained in this bulletin supersedes Service Bulletin No. T-SB-0033-14. ? Applicability has been updated to include 2019 model year Toyota vehicles. Service Bulletin No. T-SB-0033-14 is obsolete and any printed versions should be discarded. Some 2006 ? 2019 model year Toyota vehicles in particular geographic areas may exhibit a condition where the HVAC evaporator drain hose has become obstructed with an insect nest. An insect repellent drain hose tip (ARINIX® Tip) is available to help minimize future occurrences of this environmental condition. For some models, a new drain hose is required to properly fit the ARINIX® Tip. Follow the procedures in this bulletin for proper handling and installation of this optional service part. NOTE The ARINIX® Tip is NOT registered or labeled for sale or use outside the United States or Puerto Rico.
T-SB-0076-19
Service Bulletin/Repair Instructions
TSB: Some 2009 ? 2019 model year Toyota vehicles with super chrome wheel finishes may become discolored and/or damaged when aftermarket cleaners, polishes, or brake dust removal products are used on wheels with super chrome finishes. Wheel cleaners and polish that contain acidic substances may damage the clear coat of the wheel, resulting in the undercoating (black) to become visible.
T-SB-0134-16-Rev
Service Bulletin/Repair Instructions
TSB: REVISION NOTICE July 01, 2019 Rev2: ? Applicability has been updated to 2019 ? 2020 model year Toyota vehicles. ? The Techstream Preparation and Process Overview sections have been updated. October 30, 2017 Rev1: ? Applicability has been updated to include 2018 model year vehicles. Any previous printed versions of this bulletin should be discarded. SUPERSESSION NOTICE The information contained in this bulletin supersedes SB No. T-SB-0012-13. Service Bulletin No. T-SB-0012-13 is obsolete and any printed versions should be discarded. Be sure to review the entire content of this bulletin before proceeding. Flash reprogramming allows the Electronic Control Unit (ECU) software to be updated without replacing the ECU. Flash calibration updates for specific vehicle models/ECUs are released as field-fix procedures described in individual Service Bulletins. This bulletin details the Techstream ECU flash reprogramming process and outlines use of the Technical Information System (TIS) and the Calibration Update Wizard (CUW). Flash calibration updates can only be applied to the vehicle/ECU combination for which they are intended. ECUs have internal security that will not allow them to be programmed with another ECU?s information. NOTE ECU is a Toyota term used to describe integrated computerized devices responsible for managing the operation of a system or subsystem. For the purposes of this bulletin, the term ?ECU? is used as a generic label for the following SAE J1930 standard references: ? Powertrain Control Module (PCM) ? Engine Control Module (ECM) ? Transmission Control Module (TCM) ? Any other Toyota specific control unit
T-TT-0537-19
Service Bulletin/Repair Instructions
TT: The blind spot monitor (BSM) sensor angle inspection is used to confirm that the BSM sensor is within the specified angle before performing axis beam adjustment. When used in conjunction with the repair manual, these BSM tips leverage SSTs and readily available tools to support sensor angle confirmation in varying shop environments.
T-SB-0025-19
Service Bulletin/Repair Instructions
TSB: Some 2009 ? 2018 model year RAV4 and 2017 ? 2018 model year iM vehicles may exhibit a grind/groan noise from the front brake pads. An updated pad kit is now available as a service part. Follow the Repair Procedure in this bulletin to address this condition.
T-TT-0468-17-Rev
Service Bulletin/Repair Instructions
TT: HVAC drain tube is found to be blocked/clogged.
T-SB-0044-16_Rev
Service Bulletin/Repair Instructions
TSB: REVISION NOTICE February 7, 2019 Rev2: * Applicability has been updated to include 2010 - 2014 model year Matrix, 2017 - 2019 model year C-HR, 2019 model year Corolla Hatchback, and 2018 - 2019 model year Toyota vehicles. G418 The Introduction and Repair Procedure sections have been updated. March 7, 2017 Rev1: * Applicability has been updated to include 2017 model year Toyota vehicles. Any previous printed versions of this bulletin should be discarded. SUPERSESSION NOTICE The information contained in this bulletin supersedes SB No. T-SB-0040-08. * Applicability has been updated to include applicable 2016 model year vehicles. Service Bulletin No. T-SB-0040-08 is obsolete and any printed versions should be discarded. Some 2010 - 2019 model year Toyota vehicles may exhibit paint stains after the removal of Rapgard. The paint stains may appear to be under the clear coat but are usually under wrinkles in the Rapgard. The wrinkles may trap water and cause the paint to stain from the trapped moisture, especially on horizontal surfaces, such as the hood, roof, and trunk. Follow the Repair Procedure in this bulletin to address this condition.
T-TT-0515-18
Service Bulletin/Repair Instructions
TT: When adjusting the Forward Recognition Camera on vehicles with Toyota Safety Sense, it can be difficult to print the repair manual target to the proper size.
T-SB-0033-14_Rev
Service Bulletin/Repair Instructions
TSB: Some vehicles in particular geographic areas may exhibit a condition where the HVAC evaporator drain hose has become obstructed with an insect nest. An insect repellent drain hose tip (ARINIX® Tip) is now available to help minimize future occurrences of this environmental condition. For some models, a new drain hose is required to properly fit the ARINIX® Tip. Follow the procedures in this bulletin for proper handling and installation of this optional service part.
T-SB-0006-15_Rev
Service Bulletin/Repair Instructions
TSB: REVISION NOTICE November 08, 2018 Rev1: REVISION NOTICE November 08, 2018 Rev1: ? The Applicability section has been updated. Any previous printed versions of this bulletin should be discarded. Applicability has been updated to include 2016 ? 2018 model year RAV4 vehicles. ? The Production Change Information and Repair Procedure sections have been updated. Any previous printed versions of this bulletin should be discarded. Some 2013 ? 2018 model year RAV4 vehicles may exhibit a condition where the center roof drip molding on the RH and/or LH side of the vehicle becomes loose. Follow the Repair Procedure in this bulletin to address this condition.
T-TT-0414-16-Rev
Service Bulletin/Repair Instructions
TT: Some customers may encounter Bluetooth® connectivity concerns such as: ? Difficulty to pair the phone. ? Intermittent Bluetooth® failure to connect to the vehicle when first turning on the vehicle. ? Various Bluetooth® Audio functions are no longer functioning with customer?s phone such as ability to change the track using the steering wheel controls. These concerns can be caused by changes made on the customer?s phone. Make sure to inquire with the customer if the connectivity concerns occurred after receiving an operating system update on their phone or if they have restored their phone data/settings recently.
T-SB-0120-18
Service Bulletin/Repair Instructions
TSB: Some 2013 ? 2017 model year RAV4 vehicles may exhibit corrosion around the rear hatch hinges. The corrosion may be present in varying degrees, ranging from paint blisters to red surface rust with perforation. Follow the Repair Procedure in this bulletin to address this condition.
T-SB-0201-17-Rev
Service Bulletin/Repair Instructions
TSB: REVISION NOTICE September 5, 2018 Rev2: ? The Production Change Information section has been added. May 08, 2017 Rev1: ? Applicability has been updated to include 2017 ? 2018 model year vehicles. ? The entire bulletin has been updated. Any previous printed versions of this bulletin should be discarded. Some 2016 ? 2018 model year RAV4 vehicles equipped with a 2AR-FE engine may exhibit a rocking (back and forth) motion when utilizing the vehicle?s cruise control between 55 and 75 mph while driving on a flat and straight freeway/highway. The Engine Control Module/ECM (SAE Term: Powertrain Control Module/PCM) logic has been modified to reduce the possibility of this condition occurring. Follow the Repair Procedure in this bulletin to address this condition.
PG004-97-Obsolet
Service Bulletin/Repair Instructions
Technical Service Bulletin: OBSOLETE NOTICE: July 31, 2018: This bulletin is now obsolete. Please see T-SB-0304-17.
PG006-01-Obsolet
Service Bulletin/Repair Instructions
Technical Service Bulletin: OBSOLETE NOTICE: July 31, 2018: This bulletin is now obsolete. Please see T-SB-0304-17.
T-TT-0503-18_Rev
Service Bulletin/Repair Instructions
TT: When used in conjunction with the Repair Manual, these Blind Spot Monitor, Forward Recognition Camera, and Front Millimeter Wave Radar tips leverage SSTs and readily available tools to support target placement in varying shop environments.
T-TT-0503-18
Service Bulletin/Repair Instructions
TT: When used in conjunction with the Repair Manual, these Blind Spot Monitor, Forward Recognition Camera, and Front Millimeter Wave Radar tips leverage SSTs and readily available tools to support target placement in varying shop environments.
T-SB-0304-17_Rev
Service Bulletin/Repair Instructions
TSB: REVISION NOTICE July 31, 2018 Rev2: ? The Supersession Notice has been updated. January 11, 2018 Rev1: ? The Supersession Notice has been updated. Any previous printed versions of this bulletin should be discarded. SUPERSESSION NOTICE The information contained in this bulletin supersedes Service Bulletin Nos. PG021-88, PG015-89, PG0015-90, PG002-91, PG002-93, PG005-97, PG007-01, PG007-07, PG006-01, PG004-97, and T-SB-0144-08. Service Bulletin Nos. PG021-88, PG015-89, PG0015-90, PG002-91, PG002-93, PG005-97, PG007-01, PG007-07, PG006-01, PG004-97, and T-SB-0144-08 are obsolete and any printed versions should be discarded. Vehicle replacement certification labels (the vinyl label installed on the driver door or door post) and VIN plates (the metal plate riveted to dashboard) may be available from Toyota, provided the request meets one of the criteria listed in this Service Bulletin. Replacement Certification Label and VIN Plate Criteria A replacement certification label and/or VIN plate may be requested if: ? The vehicle was in an accident and the label and/or plate is damaged or attached to a part that will be replaced during the repair. ? The label and/or plate was stolen.
T-SB-0234-17_Rev
Service Bulletin/Repair Instructions
TSB: REVISION NOTICE July 20, 2018 Rev2 ? Applicability has been updated to include 2018 model year Corolla, Prius C, RAV4, and RAV4 HV vehicles. ? The entire bulletin has been updated. February 21, 2018 Rev1: ? The Introduction and Software Update sections have been updated. Any previous printed versions of this bulletin should be discarded. SUPERSESSION NOTICE The information contained in this bulletin supersedes Service Bulletin No. T-SB-0019-16. ? The Software Update section has been updated. Service Bulletin No. T-SB-0019-16 is obsolete and any printed versions should be discarded.
T-TT-0501-18-Rev
Service Bulletin/Repair Instructions
TT: Some customers may experience a voice recognition inoperative condition or abnormal Entune? operation after performing an Entune? update.
T-TT-0501-18_Rev
Service Bulletin/Repair Instructions
TT: Some customers may experience a voice recognition inoperative condition or abnormal Entune operation after performing an Entune update.
T-TT-0501-18
Service Bulletin/Repair Instructions
TT: Some customers may experience a voice recognition inoperative condition or abnormal Entune? operation after performing an Entune? update.
T-SB-0187-12_Rev
Service Bulletin/Repair Instructions
TSB: REVISION NOTICE February 12, 2018 Rev2: ? Applicability has been updated to include 2015 ? 2018 model year vehicles. January 23, 2014 Rev1: ? Applicability has been updated to include 2013 ? 2014 model year vehicles. Any previous printed versions of this bulletin should be discarded. Toyota vehicles are equipped with either conventional or run-flat tires. Sometimes punctures may occur as a result of contact with road debris or other hazards. If a puncture occurs, it may be possible to repair the tire and return it to service. With a conventional tire it is not possible to drive for an extended amount of time with the tire at low pressures as damage to the tire may occur. With run-flat tires, due to reinforced sidewalls, it is possible to drive for up to 100 miles at speeds less than 55 mph with little or no damage to the tire. The U.S. Tire Manufacturers Association (UTSMA) provides guidelines and recommendations for tire repair and replacement. It also provides information related to: ? Basic tire information ? Tire maintenance and safety ? Driver education, tire safety curriculum.
T-SB-0009-18
Service Bulletin/Repair Instructions
TSB: The purpose of this Service Bulletin is to elevate awareness and provide best practices for leather and synthetic leather care in Toyota vehicles. As an additional resource, if the vehicle is equipped with factory leather seats, the vehicle Owner?s Manual will highlight the importance of proper maintenance and provide guidance for care.
T-SB-0336-17
Service Bulletin/Repair Instructions
TSB: Some 2014 ? 2018 model year Toyota vehicles may exhibit a MIL ?ON? condition with Diagnostic Trouble Code (DTC) P2610 (Engine Off Timer Performance) present. The Engine Control Module (ECM) (SAE term: Powertrain Control Module [PCM]) logic has been modified to reduce the possibility of this condition. Follow the Repair Procedure below to address this condition.
T-SB-0229-12_Rev
Service Bulletin/Repair Instructions
TSB: REVISION NOTICE November 22, 2017 Rev1: ? Applicability has been updated to include 2014 ? 2018 model year vehicles. Any previous printed versions of this bulletin should be discarded. In the event that a Toyota vehicle becomes submerged in water, many components may be physically damaged. Electrical and electronic components, including wiring harnesses, are particularly susceptible to corrosion and subsequent malfunction. Although any flooding can be damaging, salt water flooding elevates the potential for abnormal conditions and may increase risks due to its highly corrosive and conductive nature. Salt residue also continues to corrode and remain conductive even after a vehicle dries. This bulletin is intended to assist with safe handling and inspection of flood damaged vehicles and to provide basic guidance on likely needed repairs.
T-SB-0134-16_Rev
Service Bulletin/Repair Instructions
TSB: REVISION NOTICE October 30, 2017 Rev1: * Applicability has been updated to include 2018 model year vehicles. SUPERSESSION NOTICE The information contained in this bulletin supersedes SB No. T-SB-0012-13. Flash reprogramming allows the Electronic Control Unit (ECU) software to be updated without replacing the ECU. Flash calibration updates for specific vehicle models/ECUs are released as field-fix procedures described in individual Service Bulletins. This bulletin details the Techstream ECU flash reprogramming process and outlines use of the Technical Information System (TIS) and the Calibration Update Wizard (CUW). Flash calibration updates can only be applied to the vehicle/ECU combination for which they are intended. ECUs have internal security that will not allow them to be programmed with another ECU's information.
T-SB-0304-17
Service Bulletin/Repair Instructions
TSB: Vehicle replacement certification labels (the vinyl label installed on the driver door or door post) and VIN plates (the metal plate riveted to dashboard) may be available from Toyota, provided the request meets one of the criteria listed in this Service Bulletin.
T-SB-0275-17
Service Bulletin/Repair Instructions
TSB: SUPERSESSION NOTICE The information contained in this bulletin supersedes SB No. T-SB-0168-13. ? The entire bulletin has been updated. Service Bulletin No. T-SB-0168-13 is obsolete and any printed versions should be discarded. Be sure to review the entire content of this bulletin before proceeding. Some 2013 ? 2017 model year RAV4 and 2016 ? 2017 model year RAV4 HV vehicles may exhibit a condition in which the LH or RH power back door actuator (power back door unit assembly set) separates from the ball mount bracket (back door damper stay bracket) on the hatch or body side. Additionally, wiring on the actuator may be damaged, causing the power back door to become inoperative with DTCs B2226, B2227, B2228, or B2229 present.
SET-TSB-17-007
Service Bulletin/Repair Instructions
Southeast Toyota Accessory LED Fog & DRL 2 in 1 light inoperative. Provide Accessory lamp diagnostics and manufacturing date inspection information.
T-SB-0218-17_Rev
Service Bulletin/Repair Instructions
TSB: REVISION NOTICE July 20, 2017 Rev1: Applicability has been updated to exclude 2007 ? 2017 model year Avanza vehicles. Some hazardous material treatment and handling regulations at the state and local level define the pre-disposal deployment of airbag and pre-tensioner assemblies as hazardous material treatment. Hazardous material treatment may require special training, certification or licensing in certain areas. TMS recommends that dealership personnel carefully review and follow ALL local and state regulations, and where necessary, contract with Environmental Protection Agency (EPA) Licensed Hazardous Waste Transportation and Disposal facilities.
T-SB-0019-16_Obs
Service Bulletin/Repair Instructions
TSB: OBSOLETE NOTICE Rev2 July 12, 2017: This bulletin is now obsolete. Please see T-SB-0234-17.
T-SB-0234-17
Service Bulletin/Repair Instructions
TSB: Some 2016 - 2017 model year vehicles equipped with Entune Audio (version UU.10.48), Entune Audio Plus (version EU.10.68 or EU.20.25 or EU.20.28) or Entune? Premium Audio (CU.10.71 or CU.10.72 or CU.20.05 or CU.20.08) may exhibit 1 or more of the following conditions. SUPERSESSION NOTICE The information contained in this bulletin supersedes SB No. T-SB-0019-16. The Software Update section has been updated.
Dealer Letter 20
Service Bulletin/Repair Instructions
Our records indicate there may be several 2017 Toyota RAV4's in your inventory that may have incorrect AALA (American Automobile Labeling Act) Labels (VIN list Attached). Please inspect these 2017 RAV4 vehicles for incorrect label content and replace as necessary with the labels included with this letter.
17-006
Service Bulletin/Repair Instructions
Rear Seat Entertainment Overhead DVD
SET-TSB-17-006
Service Bulletin/Repair Instructions
This Publication discusses how to find the diagnostic information and component exchange information for the Southeast Toyota accessory overhead DVD player.
T-TT-0441-17
Service Bulletin/Repair Instructions
TT: During previous air conditioning service, leakage prevention agent (A/C stop leak) may have been added to the A/C system. Adding stop leak products to the A/C system is not a recommended or approved Toyota repair process. During A/C service, moisture enters the A/C system, and can react with the previously added A/C stop leak, forming a gelatinous substance. The gel substance that forms can cause the A/C compressor to bind and or seize.
GST-TSB-17-001
Service Bulletin/Repair Instructions
This communication is informing dealer principals, general managers, service managers & parts managers of a Technical Service Bulletin initiated by Gulf States Toyota, Inc. (GST) to inspect and repair Toyota Rav4 and Corolla vehicles equipped with a Premium Security System which exhibit improper function of the alarm due to an open Power Outlet No.1 fuse. The Non-Toyota Premium Security Systems were installed as a GST installed option under GST P/N 00012-V1320-01 and 00012-V1620-01.
T-TT-0437-17
Service Bulletin/Repair Instructions
TT: Some customers may experience greyed out buttons or inactive screens (lockouts) while driving. This is to promote safe driving practices and reduce the amount of distractions while driving. These lockouts can?t be deactivated or defeated through any settings. The following is a list of common lockouts, however, this is not a complete list of lockouts.
T-SB-0184-17
Service Bulletin/Repair Instructions
TSB: This Service Bulletin includes precautions and key points for the front camera for Toyota Safety Sense C and Toyota Safety Sense P adjustment procedures.
TSB018217
Service Bulletin/Repair Instructions
TSB: SUPERSESSION NOTICE The information contained in this bulletin supersedes SB No. T-SB-0101-11. Applicability has been updated to include 2016 ? 2017 model year vehicles. Service Bulletin No. T-SB-0101-11 is Obsolete and any printed versions should be discarded. Be sure to review the entire content of this bulletin before proceeding. When servicing interior electrical switches and components, please note the precautions in this bulletin to avoid damaging electrical components and switches. Many lubricants, cleaners, and automotive chemicals contain silicone or other compounds that may contaminate electrical contacts, and therefore increase electrical resistance and decrease switch performance. The use of any cleaners or fluids may increase the risk of further damage to electrical components.
T-SB-0142-13 Rev
Service Bulletin/Repair Instructions
TSB: REVISION NOTICE November 10, 2016 Rev2: ? Applicability has been updated to include 2016 ? 2017 model year Toyota vehicles. ? Parts Information section has been updated. Some 2004 ? 2017 model year Toyota vehicles may exhibit odors naturally occurring from the HVAC system and/or related environmental factors. Although there is no way to eliminate these odors, follow the General Procedure in this bulletin to minimize the odors experienced.
T-TT-0309-14 Rev
Service Bulletin/Repair Instructions
TT: Some customers may experience Bluetooth disconnections or loss of SMS text message functionality on the navigation/audio system with Android phones running OS 4.4 or later. Condition tends to occur to customers who have many previous text messages on their phones.
T-SB-0134-16
Service Bulletin/Repair Instructions
TSB: Supersession Notice. Flash reprogramming allows the ECU software to be updated without replacing the ECU. Flash calibration updates for specific vehicle models/ECUs are released as field-fix procedures described in individual Service Bulletins. This bulletin details the Techstream ECU flash reprogramming process and outlines use of the Technical Information System (TIS) and the Calibration Update Wizard (CUW). Flash calibration updates can only be applied to the vehicle/ECU combination for which they are intended. ECUs have internal security that will not allow them to be programmed with another ECU?s information.
T-TT-0414-16
Service Bulletin/Repair Instructions
TT: Some customers may encounter Bluetooth® connectivity concerns such as: *Difficulty to pair the phone. *Intermittent Bluetooth® failure to connect to the vehicle when first turning on the vehicle. *Various Bluetooth® Audio functions are no longer functioning with customer's phone such as ability to change the track using the steering wheel controls.
T-SB-0109-16
Service Bulletin/Repair Instructions
TSB: 2017 PRE-DELIVERY SERVICE CHECK SHEET
T-SB-0110-16
Service Bulletin/Repair Instructions
TSB: PRE-DELIVERY SERVICE (PDS) IS A CRITICAL STEP IN SATISFYING OUR NEW CAR CUSTOMERS. CUSTOMER FEEDBACK INDICATES THE FOLLOWING AREAS DESERVE SPECIAL ATTENTION WHEN PERFORMING PDS: *CAREFUL INSPECTION FOR PAINT CHIPS/SCRATCHES AND BODY DENTS/DINGS. *PROPER OPERATION OF ELECTRICAL ACCESSORIES (INCLUDING INTERIOR LIGHT, CLOCK, AND RADIO RESET). *INTERIOR CLEANLINESS. *PROPER FUNCTION OF MECHANICAL SYSTEMS.
T-SB-0093-16
Service Bulletin/Repair Instructions
TSB: The Parking Assist Monitor System assists the driver during parking and parallel parking by displaying an image of the area behind the vehicle. When the D/C Cut Fuse is removed or battery terminal is disconnected, the power source to the steering angle sensor is cut off. When the D/C CUT fuse is reinstalled or the battery terminal is reconnected, the rear view monitor will operate, but it may not display estimated course lines to assist parking operation until the system has initialized. Initialize the Parking Assist Monitor System after installing the D/C CUT fuse during Pre-Delivery Service (PDS).
Safety Recall an
Service Bulletin/Repair Instructions
Update on Technician Certification Requirements.
T-SB-0039-16 REV
Service Bulletin/Repair Instructions
TSB: A BATTERY IN A STORED VEHICLE IS SUBJECT TO CONDITIONS THAT CAN REDUCE ITS PERFORMANCE AND LIFE. THESE CONDITIONS INCLUDE STORAGE PERIOD, TEMPERATURE, PARASITIC DRAIN, AND BATTERY LOAD. BECAUSE OF THESE FACTORS, BATTERY INSPECTION AND MAINTENANCE ARE REQUIRED IN ORDER TO ENSURE PROPER OPERATION AND OPTIMAL BATTERY LIFE.
TSB-0039-16 Rev1
Service Bulletin/Repair Instructions
TSB: A battery in a stored vehicle is subject to conditions that can reduce its performance and life. These conditions include storage period, temperature, parasitic drain, and battery load. Because of these factors, battery inspection and maintenance are required in order to ensure proper operation and optimal battery life.
T-TT-0399-16
Service Bulletin/Repair Instructions
TT: Multimedia systems reset procedure should be performed when the multimedia system no longer responds or reboots itself.
T-SB-0045-16
Service Bulletin/Repair Instructions
TSB: Long-term or off-site storage requires special care to keep vehicles factory fresh and ready for delivery. The following guidelines should be performed to minimize vehicle component/part degradation due to extended vehicle storage conditions. Long-term storage can affect a vehicle?s systems and components. Any problems that are found should be corrected immediately.
T-SB-0042-16
Service Bulletin/Repair Instructions
TSB: Tire Positioning Before New Vehicle Delivery During the manufacturing process, tires are nounted on the vehicle as matched sets to help reduce conditions such as pulling or drifting. If the wheels are replaced or refinished before vehicle delivery, it is important that the tires remain on the vehicle in the same location and in the direction of rotation.
T-SB-0039-16
Service Bulletin/Repair Instructions
TSB: A battery in a stored vehicle is subject to conditions that can reduce its performance and life. These conditions include storage period, temperature, parasitic drain, and battery load. Because of these factors, battery inspection and maintenance are required in order to ensure proper operation and optimal battery life. As a matter of policy, Toyota does not provide battery warranty coverage for discharged and/or failed batteries due to lack of maintenance. It is the dealer?s responsibility to maintain the specified State of Charge (SOC) of the vehicle?s battery while in stock and assure proper State of Charge (SOC) at delivery. To eliminate customer service concerns due to an undercharged battery during the first few weeks of ownership, ALL dealers should check battery State of Charge (SOC) and recharge, if necessary, within 48 hours of delivery to customers.
T-SB-0037-16
Service Bulletin/Repair Instructions
TSB: Some 2017 model year vehicles are equipped with a Smart Key system, which allows the customer to enter and start the vehicle without using a mechanical key. To ensure the system is operating properly, the Smart Key functions (Smart Entry and Smart Start) should be inspected using the following procedure during Pre-Delivery Service (PDS). Note: Check ALL of the Smart Keys using this procedure.
T-SB-0038-16
Service Bulletin/Repair Instructions
TSB: 2017 model year vehicles are equipped with driver?s side floor mat retaining clips to secure the floor mat in the correct position. In addition, some models may utilize retaining clips for passenger side and rear seat floor mats as well. Follow the appropriate Installation Procedure to attach the driver?s side, and if applicable, the passenger?s side and rear seat floor mats to the vehicle carpet using the floor mat retaining clips during Pre-Delivery Service (PDS).
T-TT-0268-13 REV
Service Bulletin/Repair Instructions
TT: SOME CUSTOMERS MAY ENCOUNTER BLUETOOTH CONNECTIVITY CONCERNS SUCH AS: DIFFICULTY PAIRING THE PHONE. INTERMITTENT BLUETOOTH FAILURE TO CONNECT WHEN FIRST TURNING ON THE VEHICLE. VARIOUS BLUETOOTH AUDIO FUNCTIONS ARE NO LONGER FUNCTIONING WITH THE CUSTOMERS PHONE, SUCH AS THE ABILITY TO CHANGE THE TRACK USING THE STEERING WHEEL CONTROLS. THESE CONCERNS CAN BE CAUSED BY CHANGES MADE ON THE CUSTOMERS PHONE. MAKE SURE TO INQUIRE WITH THE CUSTOMER IF THE CONNECTIVITY CONCERNS OCCURRED AFTER RECEIVING AN OPERATING SYSTEM UPDATE ON THEIR PHONE OR IF THEY HAVE RESTORED THEIR PHONE DATA/SETTINGS RECENTLY.
TTT-0268-13 Rev3
Service Bulletin/Repair Instructions
TT: Some customers may encounter Bluetooth connectivity concerns such as: ? Difficulty pairing the phone. ? Intermittent Bluetooth failure to connect when first turning on the vehicle. ? Various Bluetooth Audio functions are no longer functioning with the customer?s phone, such as the ability to change the track using the steering wheel controls. These concerns can be caused by changes made on the customer?s phone. Make sure to inquire with the customer if the connectivity concerns occurred after receiving an operating system update on their phone or if they have restored their phone data/settings recently.
T-PG007-01
Service Bulletin/Repair Instructions
Replacement vin plates.
T-PG002-91
Service Bulletin/Repair Instructions
Product general information.