26TC03
Service Campaign
TECHNICAL INSTRUCTIONS FOR EMISSION NONCOMPLIANCE RECALL 26TC03 Certain 2022 – 2025 Model Year RAV4 Incorrect Mass Air Flow Sensor Reading
Vehicle report
Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
26TC03
TECHNICAL INSTRUCTIONS FOR EMISSION NONCOMPLIANCE RECALL 26TC03 Certain 2022 – 2025 Model Year RAV4 Incorrect Mass Air Flow Sensor Reading
T-SB-0023-26
Some customers may experience a rough running engine with a MIL ON P140018 DTC. Upon further inspection, a loose C90/C27 connector pin at the EGR valve may be found. To correct this concern, please reference the repair section of this TSB.
T-SB-0104-21 Rev2
OBSOLETE NOTICE February 27, 2026: This bulletin is no longer applicable and is now obsolete.
T-SB-0106-22 Rev2
OBSOLETE NOTICE January 30, 2026: This bulletin is now obsolete. Please see T-SB-0001-26.
T-SB-0001-26
Some 2018 – 2024 model year Toyota vehicles equipped with a Premium Audio with Dynamic Navigation System require a Special Service Tool (SST) USB flash drive to update the map, points of interest, and system software.
T-TT-0797-26
Some RAV4 vehicles power seat where the automatic seat adjustment by the memory function does not work.
T-SB-0055-24 Rev2
Some 2005 – 2026 Toyota vehicles that have undergone water intrusion may exhibit a condition in which a musty odor is present. Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this Service Bulletin is to provide general guidelines and procedures for odor remediation. This Service Bulletin provides a guide on how to prepare and treat the interior of the vehicle for odor remediation. Refer to the applicable model and model year Repair Manual and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines.
22TE09
Although the HV Floor Under Wire Harness and Rear Traction Motor Cable is covered by Toyota’s New Vehicle Limited Warranty for 3 years or 36,000 miles (whichever comes first), we at Toyota care about the customers’ ownership experience. Toyota is providing extended coverage under this Customer Support Program for repairs related to excessive corrosion to the wire harness connections at the Rear Motor Generator. Excessive corrosion can cause AM Radio Static during certain drive cycles, or the vehicle may not start.
T-SB-0010-24 Rev2
Some 2021 – 2022 model year Avalon, 2018 – 2024 Camry, 2019 – 2025 model year Corolla, 2022 – 2025 model year Corolla Cross, and 2019 – 2025 model year RAV4 vehicles with A25A-FKS and M20A-FKS engines may have a MIL ON condition with one or more of the following Diagnostic Trouble Codes (DTCs) upon cold soak start up with engine coolant temperatures between 14°F – 41°F: •P030027 – Random/Multiple Cylinder Misfire Detected (Emission) Signal Rate of Change Above Threshold •P030000 – Random/Multiple Cylinder Misfire Detected •P030100 – Cylinder 1 Misfire Detected •P030200 – Cylinder 2 Misfire Detected •P030300 – Cylinder 3 Misfire Detected •P030400 – Cylinder 4 Misfire Detected
T-SB-0058-23 Rev1
The air conditioning dye injection tool kit has been developed to aid in identifying the location of air conditioning refrigerant leaks. The procedures outlined in this Service Bulletin aid in locating, inspecting, and repairing refrigerant leaks.
T-SB-0005-24 Rev2
Some 2021 model year Avalon, 2020 – 2022 model year Camry, and 2019 – 2022 model year RAV4 vehicles equipped with an A25A-FKS engine may exhibit reduced engine power and/or a MIL ON condition with one or more of the following throttle body Diagnostic Trouble Codes (DTCs) present in freezing temperatures: •P01201C: Throttle / Pedal Position Sensor / Switch “A” Circuit Voltage Out of Range. •P210015: Throttle Actuator “A” Control Motor Circuit Short to Battery or Open. •P210019: Throttle Actuator “A” Control Motor Circuit Current Above Threshold. •P211172: Throttle Actuator “A” Control System Actuator Stuck Open. The Engine Control Module (ECM) (SAE term: Powertrain Control Module/PCM) logic and the fuel pump assembly have been modified to address these conditions.
T-TT-0780-25
To assist with the early detection and early resolution of audio related concerns you may be asked to recover MMR data from the head unit. The following steps are instructions on how to retrieve the data from the system and are only to be used when requested by FTS and/or FPE.
T-SB-0013-24 Rev1
The Immobilizer and Smart Key Reset is a feature that allows the registration of new keys when all master keys are lost. Once the system is reset, all previously registered keys will be erased and can never be reused. Another feature, Add/Remove Key, is also available. Once a key is removed, it can never be reused.
T-TT-0771-25
Some 2021-2025 MY Highlander HV, Sienna HV, RAV4, and RAV4 HV, may exhibit an oil leak from the area where the camshaft cover, camshaft housing, and the timing chain covers meet. This is typically seen on the exhaust side of the engine.
LSB006523
TT: Engine Oil Leak between the Lower Oil Pan and Crank Case
T-SB-0010-24 Rev1
Some 2021 – 2022 model year Avalon, 2018 – 2024 Camry, 2019 – 2025 model year Corolla, 2022 – 2025 model year Corolla Cross, and 2019 – 2025 model year RAV4 vehicles with A25A-FKS and M20A-FKS engines may have a MIL ON condition with one or more of the following Diagnostic Trouble Codes (DTCs) upon cold soak start up with engine coolant temperatures between 14°F – 41°F: •P030027 – Random/Multiple Cylinder Misfire Detected (Emission) Signal Rate of Change Above Threshold •P030000 – Random/Multiple Cylinder Misfire Detected •P030100 – Cylinder 1 Misfire Detected •P030200 – Cylinder 2 Misfire Detected •P030300 – Cylinder 3 Misfire Detected •P030400 – Cylinder 4 Misfire Detected
T-SB-0001-22 Rev2
Some 2019 – 2025 model year RAV4 and RAV4 Hybrid vehicles may exhibit a squeal/squeak noise from the front brakes with light to moderate braking.
T-SB-0035-24 Rev2
Acid rain results from rainwater or other airborne moisture that become acidic due to industrial chemical impurities in the atmosphere. If these acidic compounds settle on an exposed vehicle, especially the horizontal areas such as the hood, roof, and decklid, significant damage to the painted surfaces can occur. Acid rain damage can typically be identified on vehicles by the presence of stains on the paint surface that resemble hard water spots. Unlike water spots however, acid rain damage cannot be removed by regular washing procedures. Also, because acid rain can etch and soften the paint, normal buffing or polishing repair procedures should not be attempted. This can cause further damage and result in visible depressions in the paint surface. The following are the three major categories of acid rain damage: •Minor damage: requires only buffing to repair. •Moderate damage: usually requires neutralizing, color sanding, and buffing. •Severe damage: extending beyond 1/2 mil of clearcoat on a pearl, metallic, or solid color, requires neutralization, sanding, and repainting. In cases where acid rain damage is minor, neutralization and buffing with a liquid-type paint finessing product may provide an adequate repair. Only specially formulated products outlined in this bulletin should be used for that purpose. Unfortunately, other than minor damage, there is no simple method of determining the actual extent (depth) of acid penetration other than color sanding a representative affected area until there is no visible etching or depressions, followed by measuring the amount of paint removed with either a magnetic or digital-type film thickness gauge. The procedures in this bulletin are intended for use by qualified body/paint technicians and should not be attempted by inexperienced personnel. It is the dealer’s responsibility to protect and maintain the quality of the vehicle’s paint finish after receipt at the dealership prior to the first sale. Perform frequent vehicle washing, as often as daily, during high heat and humidity periods to minimize the potential for paint damage due to acid rain exposure. This is especially important in geographical areas known for high frequency and concentration of acid rain and industrial fallout.
T-SB-0038-24 Rev2
To prevent brake rotor rust from forming during transportation and storage, wheel film will be used instead of a cardboard type of anti-rust cover. The purpose of the wheel film is to shield the disc brake rotor from weather elements and initial rust before the vehicle is delivered to the customer. Consequently, the film should remain on the wheel for as long as possible.
T-SB-0039-24 Rev2
The condition known as acid rain is caused by airborne chemicals or particles in the atmosphere, which mix with rainwater, nighttime dew, or high humidity to form acidic compounds. If these contaminants settle and remain on a painted vehicle surface, especially the horizonal areas of the hood, roof, and decklid, significant damage can occur. This damage is the result of actual etching of the paint and appears as pitting or water spots. As acid rain droplets on the vehicle surface evaporate, the concentration strength of the acid increases, causing deeper and more rapid damage. This evaporation and corrosive action also occur more rapidly on dark colored cars as direct sun heat increases. It is the dealer’s responsibility to protect and maintain the quality of the vehicle’s paint finish after receipt at the dealership prior to the first sale. In areas known for high frequency and/or concentration of acid rain, frequent vehicle washing during high heat or humidity periods will minimize the potential for paint damage caused by acid rain. It is further recommended that either reverse osmosis or deionized water be used to prevent water spotting.
T-SB-0061-23 Rev2
Toyota vehicles are currently protected with RapgardTM protective film designed to protect the horizontal painted surfaces. This material protects from acid rain, environmental fallout, and rail contamination. Follow the Removal Procedure in this bulletin to remove the RapgardTM protective film within 90 days from initial application.
T-SB-0062-23 Rev2
Vehicles may occasionally be subjected to contamination by airborne iron particles shed from railroad tracks, train wheels, exposure to heavy machinery facilities, grinding, welding, etc. This type of contamination can be identified by the presence of small, red or brown particles on the paint surface. These particles are often difficult to see on dark color paints but can be easily felt when brushing a hand across horizontal body surfaces such as the hood, roof, or deck lid. Follow the Repair Procedure in this bulletin to clean vehicles that may have been subjected to contamination by airborne iron particles such as rail dust during rail transportation or extended storage near industrial areas.
T-TT-0768-24
Some technicians may report an engine oil leak from the Engine Oil Level Sensor area
23TJ01
The table below describes the phases currently planned for the Second Key Delivery Program and the estimated timing of announcement. This table will be updated during each phase launch and as more details become available.
T-TT-0764-24 Rev1
Customers may experience a MIL ON, or an intermittent MIL ON condition, accompanied by DTC P140018, Exhaust Gas Recirculation "A" Control Circuit 2 Circuit Current Below Threshold
T-SB-0098-24
Some 2022 model year Avalon and Avalon Hybrid, 2022 – 2024 model year Camry, Camry Hybrid, Corolla, Corolla Hatchback, Corolla Hybrid, Highlander, Highlander Hybrid, Prius, Prius Prime, RAV4, RAV4 Hybrid, RAV4 Prime, and Venza Hybrid, 2023 – 2024 model year Crown, and 2024 model year Grand Highlander vehicles may exhibit a high-pitched noise coming from the front HVAC blower motor while operating the air conditioner or heater. This condition does not affect the operation of the vehicle, however, a heater cover has been developed to help reduce or potentially eliminate the noise.
T-TT-0764-24
Customers may experience a MIL ON, or an intermittent MIL ON condition, accompanied by DTC P140018, Exhaust Gas Recirculation "A" Control Circuit 2 Circuit Current Below Threshold
T-TT-0763-24
P010012 or P010014 DTC sets after driving in the rain. DTC P010012/14 is currently under investigation.
T-SB-0055-24 Rev1
Some 2005 – 2024 Toyota vehicles that have undergone water intrusion may exhibit a condition in which a musty odor is present. Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this Service Bulletin is to provide general guidelines and procedures for odor remediation. This Service Bulletin provides a guide on how to prepare and treat the interior of the vehicle for odor remediation. Refer to the applicable model and model year Repair Manual and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines. This Service Bulletin is to provide a general overview and direction for the odor remediation process.
T-SB-0035-24 Rev1
Acid rain results from rainwater or other airborne moisture that become acidic due to industrial chemical impurities in the atmosphere. If these acidic compounds settle on an exposed vehicle, especially the horizontal areas such as the hood, roof, and decklid, significant damage to the painted surfaces can occur. Acid rain damage can typically be identified on vehicles by the presence of stains on the paint surface that resemble hard water spots. Unlike water spots however, acid rain damage cannot be removed by regular washing procedures. Also, because acid rain can etch and soften the paint, normal buffing or polishing repair procedures should not be attempted. This can cause further damage and result in visible depressions in the paint surface. The following are the three major categories of acid rain damage: •Minor damage: requires only buffing to repair. •Moderate damage: usually requires neutralizing, color sanding, and buffing. •Severe damage: extending beyond 1/2 mil of clearcoat on a pearl, metallic, or solid color, requires neutralization, sanding, and repainting. In cases where acid rain damage is minor, neutralization and buffing with a liquid-type paint finessing product may provide an adequate repair. Only specially formulated products outlined in this bulletin should be used for that purpose. Unfortunately, other than minor damage, there is no simple method of determining the actual extent (depth) of acid penetration other than color sanding a representative affected area until there is no visible etching or depressions, followed by measuring the amount of paint removed with either a magnetic or digital-type film thickness gauge. The procedures in this bulletin are intended for use by qualified body/paint technicians and should not be attempted by inexperienced personnel. It is the dealer’s responsibility to protect and maintain the quality of the vehicle’s paint finish after receipt at the dealership prior to the first sale. Perform frequent vehicle washing, as often as daily, during high heat and humidity periods to minimize the potential for paint damage due to acid rain exposure. This is especially important in geographical areas known for high frequency and concentration of acid rain and industrial fallout.
T-SB-0038-24 Rev1
To prevent brake rotor rust from forming during transportation and storage, wheel film will be used instead of a cardboard type of anti-rust cover. The purpose of the wheel film is to shield the disc brake rotor from weather elements and initial rust before the vehicle is delivered to the customer. Consequently, the film should remain on the wheel for as long as possible.
T-SB-0039-24 Rev1
The condition known as acid rain is caused by airborne chemicals or particles in the atmosphere, which mix with rainwater, nighttime dew, or high humidity to form acidic compounds. If these contaminants settle and remain on a painted vehicle surface, especially the horizonal areas of the hood, roof, and decklid, significant damage can occur. This damage is the result of actual etching of the paint and appears as pitting or water spots. As acid rain droplets on the vehicle surface evaporate, the concentration strength of the acid increases, causing deeper and more rapid damage. This evaporation and corrosive action also occur more rapidly on dark colored cars as direct sun heat increases. It is the dealer’s responsibility to protect and maintain the quality of the vehicle’s paint finish after receipt at the dealership prior to the first sale. In areas known for high frequency and/or concentration of acid rain (see Figure 1), frequent vehicle washing during high heat or humidity periods will minimize the potential for paint damage caused by acid rain. It is further recommended that either reverse osmosis or deionized water be used to prevent water spotting.
T-SB-0055-24
Some 2005 – 2024 Toyota vehicles that have undergone water intrusion may exhibit a condition in which a musty odor is present. Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this Service Bulletin is to provide general guidelines and procedures for odor remediation. This Service Bulletin provides a guide on how to prepare and treat the interior of the vehicle for odor remediation. Refer to the applicable model and model year Repair Manual and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines.
T-SB-0103-20 Rev1
This Service Bulletin provides updated non-electric water pump leak inspection and diagnostic tips for some 2008 – 2025 model year Toyota vehicles.
Toyota Renotification DL
Safety Recall and Service Campaign completion is an important part of our commitment to customer satisfaction of Toyota products. Toyota will be conducting follow-up notifications to remind owners whose vehicles have not yet had Safety Recall and/or Service Campaign repairs completed in the campaigns listed
Toyota Renotification RL
Toyota plans to conduct Safety Recall and Service Campaign follow-up notifications to owners whose vehicles have not yet had the following Safety Recall and/or Service Campaign repairs completed
T-SB-0005-24 Rev1
Some 2021 model year Avalon, 2020 – 2022 model year Camry, and 2019 – 2022 model year RAV4 vehicles equipped with an A25A-FKS engine may exhibit reduced engine power and/or a MIL ON condition with one or more of the following throttle body Diagnostic Trouble Codes (DTCs) present in freezing temperatures: •P01201C: Throttle / Pedal Position Sensor / Switch “A” Circuit Voltage Out of Range. •P210015: Throttle Actuator “A” Control Motor Circuit Short to Battery or Open. •P210019: Throttle Actuator “A” Control Motor Circuit Current Above Threshold. •P211172: Throttle Actuator “A” Control System Actuator Stuck Open. The Engine Control Module (ECM) (SAE term: Powertrain Control Module/PCM) logic and the fuel pump assembly have been modified to address these conditions.
T-SB-0061-23 Rev1
Toyota vehicles are currently protected with RapgardTM protective film designed to protect the horizontal painted surfaces. This material protects from acid rain, environmental fallout, and rail contamination.
T-SB-0062-23 Rev1
Vehicles may occasionally be subjected to contamination by airborne iron particles shed from railroad tracks, train wheels, exposure to heavy machinery facilities, grinding, welding, etc. This type of contamination can be identified by the presence of small, red or brown particles on the paint surface. These particles are often difficult to see on dark color paints but can be easily felt when brushing a hand across horizontal body surfaces such as the hood, roof, or deck lid.
T-SB-0035-24
Acid rain results from rainwater or other airborne moisture that become acidic due to industrial chemical impurities in the atmosphere. If these acidic compounds settle on an exposed vehicle, especially the horizontal areas such as the hood, roof, and decklid, significant damage to the painted surfaces can occur. Acid rain damage can typically be identified on vehicles by the presence of stains on the paint surface that resemble hard water spots. Unlike water spots however, acid rain damage cannot be removed by regular washing procedures. Also, because acid rain can etch and soften the paint, normal buffing or polishing repair procedures should not be attempted. This can cause further damage and result in visible depressions in the paint surface. The following are the three major categories of acid rain damage: •Minor damage: requires only buffing to repair. •Moderate damage: usually requires neutralizing, color sanding, and buffing. •Severe damage: extending beyond 1/2 mil of clearcoat on a pearl, metallic, or solid color, requires neutralization, sanding, and repainting. In cases where acid rain damage is minor, neutralization and buffing with a liquid-type paint finessing product may provide an adequate repair. Only specially formulated products outlined in this bulletin should be used for that purpose. Unfortunately, other than minor damage, there is no simple method of determining the actual extent (depth) of acid penetration other than color sanding a representative affected area until there is no visible etching or depressions, followed by measuring the amount of paint removed with either a magnetic or digital-type film thickness gauge. The procedures in this bulletin are intended for use by qualified body/paint technicians and should not be attempted by inexperienced personnel. While the quality and durability of paint on Toyota vehicles is continuously being improved, it remains the dealer’s responsibility to protect and maintain the quality of the vehicle’s paint finish after receipt at the dealership prior to the first sale. To read, While the quality and durability of paint on Toyota vehicles is continuously being improved, it remains the dealer’s responsibility to protect and maintain the quality of the vehicle’s paint finish after receipt at the dealership prior to first sale. Perform frequent vehicle washing, as often as daily, during high heat and humidity periods to minimize the potential for paint damage due to acid rain exposure. This is especially important in geographical areas known for high frequency and concentration of acid rain and industrial fallout.
T-SB-0038-24
To prevent brake rotor rust from forming during transportation and storage, wheel film will be used instead of a cardboard type of anti-rust cover. The purpose of the wheel film is to shield the disc brake rotor from weather elements and initial rust before the vehicle is delivered to the customer. Consequently, the film should remain on the wheel for as long as possible. SUPERSESSION NOTICE The information contained in this bulletin supersedes Service Bulletin No. PD017-04. •The entire bulletin has been updated.
T-SB-0039-24
The condition known as acid rain is caused by airborne chemicals or particles in the atmosphere, which mix with rainwater, nighttime dew, or high humidity to form acidic compounds. If these contaminants settle and remain on a painted vehicle surface, especially the horizonal areas of the hood, roof, and decklid, significant damage can occur. This damage is the result of actual etching of the paint and appears as pitting or water spots. As acid rain droplets on the vehicle surface evaporate, the concentration strength of the acid increases, causing deeper and more rapid damage. This evaporation and corrosive action also occur more rapidly on dark colored cars as direct sun heat increases. While Toyota paint quality, durability, and resistance to environmental factors is continuously being improved, it remains the responsibility of the dealer to protect and maintain the vehicle’s paint finish from the time of arrival at the dealership until retail delivery to the customer. In areas known for high frequency and/or concentration of acid rain (see Figure 1), frequent vehicle washing during high heat or humidity periods will minimize the potential for paint damage caused by acid rain. It is further recommended that either reverse osmosis or deionized water be used to prevent water spotting.
23TJ01 Eligibility
The table describes the phases currently planned for the Second Key Delivery Program and the estimated timing of announcement. This table will be updated during each phase launch and as more details become available.
T-TT-0754-24
Customers have expressed concerns about the performance of Qi Wireless Chargers. Wireless chargers on applicable vehicles are designed to work with Qi Certified devices only. MagSafe devices, that are not Qi Certified, may not charge as expected with Qi Wireless Chargers.
23TJ01_P5_Dealer
DP: The subject vehicles were delivered with only one (1) Smart Key on select models since October 2022 due to a global semiconductor shortage impacting certain microchips. The affected vehicles were delivered with one (1) Smart Key and a second mechanical key.
Toyota Second Ke
The table describes the phases currently planned for the Second Key Delivery Program and the estimated timing of announcement. This table will be updated during each phase launch and as more details become available.
T-PANT-2024-004-
This is to advise of various price adjustments that will affect Toyota Genuine Motor Oil and Long Life Coolant, effective March 1, 2024. These products are ordered through the Toyota Complete Maintenance Care (TCMC) website.
T-SB-0013-24
TSB: The Immobilizer and Smart Key Reset is a feature that allows the registration of new keys when all master keys are lost. Once the system is reset, all previously registered keys will be erased and can never be reused. Another feature, Add/Remove Key, is also available. Once a key is removed, it can never be reused.
23TJ01 Current P
The table describes the phases currently planned for the Second Key Delivery Program and the estimated timing of announcement. This table will be updated during each phase launch and as more details become available.
22TE09a
TI: TECHNICAL INSTRUCTIONS FOR CUSTOMER SUPPORT PROGRAM 22TE09 HV FLOOR UNDER WIRE HARNESS AND REAR TRACTION MOTOR CABLE CORROSION CERTAIN 2021 ? 2022 MODEL YEAR RAV4 PRIME
TSB001024
TSB: Some 2021 ? 2022 model year Avalon, 2018 ? 2024 Camry, and 2019 ? 2024 RAV4 vehicles with A25A-FKS engines may have a MIL ON condition with one or more of the following Diagnostic Trouble Codes (DTCs) upon cold soak start up with engine coolant temperatures between 14°F ? 41°F: ?P030027 ? Random/Multiple Cylinder Misfire Detected (Emission) Signal Rate of Change Above Threshold ?P030000 ? Random/Multiple Cylinder Misfire Detected ?P030100 ? Cylinder 1 Misfire Detected ?P030200 ? Cylinder 2 Misfire Detected ?P030300 ? Cylinder 3 Misfire Detected ?P030400 ? Cylinder 4 Misfire Detected Follow the Repair Procedure in this bulletin to address these conditions.
TSB010622
TSB: Some 2018 ? 2022 model year Toyota vehicles equipped with a Premium Audio with Dynamic Navigation System require a Special Service Tool (SST) USB flash drive to update the map, points of interest, and system software. The SST is used with applicable vehicles to deliver the update, however, the process for generating license keys differs from previous generations. Before attempting to perform a map update, the expiration date of the dynamic subscription (stored in the head unit), must be checked. If the expiration date has not passed, a license key may be generated without the purchase of an Activation Card Number (ACN). Updating the map without the use of an ACN is considered an Embedded Navigation Update (refer to pg. 10) and performing this update does not extend the subscription to dynamic map services. If the subscription period has expired, or is expiring within the next 90 days, it should be recommended to the customer to purchase an ACN. Utilizing an ACN, will initiate the Dynamic Navigation Update (refer to pg. 4). This Dynamic Navigation Update will perform the embedded navigation update and provide dynamic map services for a period of two years from the date that the Dynamic Navigation Update is performed. ACNs are provided in a pamphlet available through the normal parts ordering system. Follow the process in this bulletin to perform the update.
TSB010421
TSB: Some 2018 ? 2024 model year Toyota vehicles equipped with an A25A-FKS, A25A-FXS, M20A-FKS, or M20A-FXS engine may exhibit one or more of the following conditions: ?Milky/discolored engine oil. ?An ?Oil Pressure Low? warning message on the Multi-information Display (MID). ?A MIL ON condition with Diagnostic Trouble Codes (DTCs) P05202A (Engine Oil Pressure Sensor/Switch ?A? Signal Stuck in Range) and/or P052477 (Engine Oil Pressure Too Low [Severe]) present. Moisture from blow-by gases condenses and accumulates in the engine oil during short trips in extreme cold weather. When the moisture in the oil freezes, the oil pressure may drop, and the aforementioned warning indicators may display. Follow the procedures in this bulletin to address these conditions.
T-TT-0702-22 Rev
TT: Some 2020-2022 vehicles equipped with North American Produced (NAP) A25A-FKS/FXS engines may experience an oil leak from the head/valve cover gasket. This issue is currently under investigation.
T-SB-0005-24
TSB: Some 2021 model year Avalon, 2020 ? 2022 model year Camry, and 2019 ? 2022 model year RAV4 vehicles equipped with an A25A-FKS engine may exhibit reduced engine power and/or a MIL ON condition with one or more of the following throttle body Diagnostic Trouble Codes (DTCs) present in freezing temperatures: ?P01201C: Throttle / Pedal Position Sensor / Switch ?A? Circuit Voltage Out of Range. ?P210015: Throttle Actuator ?A? Control Motor Circuit Short to Battery or Open. ?P210019: Throttle Actuator ?A? Control Motor Circuit Current Above Threshold. ?P211172: Throttle Actuator ?A? Control System Actuator Stuck Open. The Engine Control Module (ECM) (SAE term: Powertrain Control Module/PCM) logic and the fuel pump assembly have been modified to address these conditions. Follow the Repair Procedure in this bulletin to address these conditions
23TJ01A
DP: The subject vehicles were delivered with only one (1) Smart Key on select models since October 2022 due to a global semiconductor shortage impacting certain microchips. The affected vehicles were delivered with one (1) Smart Key and a second mechanical key.
23TJ01P4B
RL: The supply of Smart Keys available for Toyota vehicles has been temporarily limited to one (1) on select models since October 2022 due to global semiconductor shortages impacting certain microchips. Affected vehicles have been delivered with only one Smart Key and a second mechanical key.
23TJ01P4C
TI: TECHNICAL INSTRUCTIONS FOR 23TJ01 Second Key Delivery Program Multiple Models and Model Years
T-TT-0678-21 Rev
TT: Some 19CY LG DCM equipped vehicles may not be able to complete the firmware update due to not having an active account or waived services during the trial. Follow the steps below to enable ?Temp DCM Activation?.
23LJ01a
RL: The supply of Smart Keys available for Toyota vehicles has been temporarily limited to one (1) on select models since October 2022 due to global semiconductor shortages impacting certain microchips. Affected vehicles have been delivered with only one Smart Key and a second mechanical key.
23TJ01b
TI: TECHNICAL INSTRUCTIONS FOR 23TJ01 Second Key Delivery Program Multiple Models and Model Years
TSB002123
TSB: Some 2020 ? 2022 model year Highlander and RAV4 vehicles, and 2022 model year Tundra vehicles equipped with a start/stop switch may exhibit water entry to the vehicle from the HVAC drain hose being disconnected from the air conditioning radiator assembly and/or a grease/oil odor emitting from the vents. This condition may be caused by paraffin wax leaking from the evaporator. Follow the repair procedure in this bulletin to address this condition.
TSB005823
TSB: The air conditioning dye injection tool kit has been developed to aid in identifying the location of air conditioning refrigerant leaks. Follow the procedures outlined in this service bulletin to aid in locating, inspecting, and repairing refrigerant leaks
TSB003220
TSB: Replacement certification labels (the vinyl label installed on the driver door or door post) and VIN plates (the metal plate riveted to dashboard) (see Figure 1) for most 1979 ? 2023 model year vehicles may be available provided the requests meet the criteria listed in this Service Bulletin. Follow the Procurement Procedure in this bulletin to request a replacement certification label or VIN plate.
TSB005123
OBSOLETE NOTICE August 17, 2023: This bulletin is no longer applicable and is now obsolete
TTT073723
TT: A very small percentage of customers experience operational difficulties with some telematics features which they cannot resolve on their own. These resources, in conjunction with the Repair Manual, are for dealership personnel to assist those customers with user issues, user errors, and compatibility issues with other vehicle systems and external applications encountered while operating telematics features. Toyota has developed and provided the following Telematics Diagnostic Guide to assist dealer technicians.
T-TT-0726-23
TT: Some 2021 - 2023 Highlander HV, RAV4 HV and Sienna HV vehicles equipped with Rear Motor Generator, MGR (Q610), may duplicate an abnormal noise (Drone, Growl, Humming, and/or other) from the MGR at various vehicle speeds and normal drive conditions. Please contact TAS for diagnostic instructions to aid in resolution of the condition.
T-TT-0728-23
TT: This issue is currently under investigation. Please create TAS case and attach a store all health check. Please contact TAS for further instructions. If it is a weekend or a holiday, continue with diagnosis and repair. Please save all parts/ or details and contact TAS on the next available workday.
TSB-0033-23
TSB: Some 2020 ? 2023 model year Highlander Hybrid and 2021 ? 2023 model year RAV4 Hybrid, RAV4 Prime, Sienna Hybrid, and Venza Hybrid vehicles may exhibit a MIL ON condition with one or both of the following Diagnostic Trouble Codes (DTCs) present: ?P24517F ? Evaporative Emission System Switching Valve Actuator Stuck Off. ?P14502A ? Fuel Tank Pressure Sensor Signal Stuck in Range.
T-SB-0021-23
TSB: Some 2020 ? 2022 model year Highlander and RAV4 vehicles, and 2022 model year Tundra vehicles equipped with a start/stop switch may exhibit water entry to the vehicle from the HVAC drain hose being disconnected from the air conditioning radiator assembly and/or a grease/oil odor emitting from the vents. This condition may be caused by paraffin wax leaking from the evaporator.
T-TT-0733-23
TT: Some 2022-2024 MY vehicles equipped with the A25A engine may exhibit a leak from the engine water pump, and/or MIL On condition accompanied by DTC(s): ?P26CA14 Engine Coolant Pump Circuit Short to Ground or Open ?P26CA31 Engine Coolant Pump No Signal
23TE01 Dealer Pa
DP: Although the high-pressure fuel pump is covered by Toyota?s New Vehicle Limited Warranty for 5 years or 60,000 miles (whichever comes first), we at Toyota care about the customers? ownership experience. Toyota is providing coverage for repairs related to the presence of a fuel odor in or around the engine bay originating at the high-pressure fuel pump of the subject vehicles.
T-TT-0699-22 Rev
TT: Some Model Year 2018-2023 vehicles equipped with A25A-FKS/FXS or M20A-FKS/FXS engines may display the following message ?Engine Maintenance Required Visit Your Dealer? on the combination meter
T-TT-0723-23
TT: Some 2021 to 2023 MY vehicles equipped Rear Motor Generator, MGR (Q610) may experience an oil leak concern. This issue is currently under investigation
TSB005822
TSB: Some 2019 ? 2022 model year RAV4 vehicles may exhibit a MIL ON condition with one or more of the following Diagnostic Trouble Codes (DTCs) present: ?P0087/P008700 ? Fuel Rail/System Pressure ? Too Low ?P107A2A ? Fuel Rail Pressure Sensor (Low) Signal Stuck in Range This condition may occur when the vehicle is operated at high altitudes and temperatures, typically above 3,300 feet (1,000 meters) and at ambient temperatures above 85°F (30°C). The Engine Control Module (ECM) (SAE term: Powertrain Control Module/PCM) and the fuel suction tube assembly have been improved to reduce the possibility of this condition. Follow the Repair Procedure in this bulletin to address this condition.
TTT070222
TT: Some 2020-2022 vehicles equipped with North American Produced (NAP) A25A-FKS/FXS engines may experience an oil leak from the head/valve cover gasket. This issue is currently under investigation.
TTT071522
TT: Some 2019- 2023 RAV4 HV vehicles may duplicate an abnormal noise (Growl, Humming and/or other) from the Hybrid T/A and/or MGR at various vehicle speeds and normal drive conditions
T-TT-0611-20 Rev
TT: To assist with the early detection and early resolution of audio related concerns, it may be requested as part of the remanufactured head unit return to recover MMR data from the head unit. The following steps are instructions on how to retrieve the data from the system and are only to be used when requested by audio suppliers, FTS, and/or FPEs.
T-SB-0106-22
TSB: Some 2018 ? 2022 model year Toyota vehicles equipped with a Premium Audio with Dynamic Navigation System, require a Special Service Tool (SST) USB flash drive to update the map, points of interest, and system software. The SST is used with applicable vehicles to deliver the update, however, the process for generating license keys differs from previous generations. Before attempting to perform a map update, the expiration date of the dynamic subscription (stored in the head unit), must be checked. If the expiration date has not passed, a license key may be generated without the purchase of an activation card number (ACN). Updating the map without the use of an ACN is considered an Embedded Navigation Update (refer to pg. 10) and performing this update does not extend the subscription to dynamic map services. If the subscription period has expired, or is expiring within the next 90 days, it should be recommended to the customer to purchase an ACN. Utilizing an ACN, will initiate the Dynamic Navigation Update (refer to pg. 4). This Dynamic Navigation Update will perform the embedded navigation update and provide dynamic map services for a period of two years from the date that the Dynamic Navigation Update is performed. ACNs are provided in a pamphlet available through the normal parts ordering system
T-SB-0001-22 Rev
TSB: Some 2019 ? 2023 model year RAV4 and RAV4 Hybrid vehicles may exhibit a squeal/squeak noise from the front brakes with light to moderate braking. Follow the Repair Procedure in this bulletin to address this condition
T-TT-0715-22
TT: Some 2019- 2023 RAV4 HV vehicles may duplicate an abnormal noise (Growl, Humming and/or other) from the Hybrid T/A and/or MGR at various vehicle speeds and normal drive conditions.
T-SB-0094-21 Rev
TSB: Some 2005 ? 2022 model year Toyota vehicles that have undergone water intrusion may exhibit a condition in which a musty smell is present. Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this service bulletin is to provide general guidelines and procedures for odor remediation. This service bulletin provides a guide on how to prepare the interior of the vehicle prior to an odor remediation being performed, as well as contact information for an approved vendor who will arrange the remediation, and instructions on how to prepare the interior of the vehicle for reassembly once the remediation has been completed. Refer to all model and model year specific Repair Manuals and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines. This service bulletin is to provide a general overview and direction for the odor remediation process.
T-TT-0714-22
TT: Some MY2022-2023 vehicles equipped with A25A-FKS or A25A-FXS engines may experience a MIL on condition with one or more of the following DTCs: P26CA12, P26CA14, P26CB71, P26CA31, P26CE37
T-TT-0708-22
TT: Some Model Year 2018-2022 vehicles equipped with A25A-FKS or A25A-FXS engines may experience a MIL ON condition with the following DTCs: P043F00, P043E00, P24007E, P24007F, P24187E
22TC05 Dealer Pa
DP: The subject vehicles may have been equipped with an engine containing an incorrectly manufactured Crankcase Case Vent. If the engine is equipped with an incorrectly manufactured Crankcase Case Vent, the vehicle may release crankcase emissions
22TC05 Technical
TI: TECHNICAL INSTRUCTIONS FOR SPECIAL SERVICE CAMPAIGN 22TC05 Crankcase Case Vent
22TC05 Region Le
RL: The subject vehicles may have been equipped with an engine containing an incorrectly manufactured Crankcase Case Vent. If the engine is equipped with an incorrectly manufactured Crankcase Case Vent, the vehicle may not comply with certain Federal emissions regulations.
T-TT-0703-22
TT: Vehicles listed above equipped with a Denso Ten radio (Entune Audio Plus or Premium Audio) may exhibit a condition in which the radio screen continues to show a Bluetooth phone call in progress after the call has ended. This condition has been confirmed with multiple Android phones, including Samsung Galaxy S21 and S22, and Google Pixel 6.
T-TT-0702-22
TT: Some 2020-2022 vehicles equipped with North American Produced (NAP) A25A-FKS/FXS engines may experience an oil leak from the head/valve cover gasket. This issue is currently under investigation.
T-TT-0668-21 Rev
TT: Some vehicles may exhibit seat memory switch function inoperative condition if the Seating Position Control ECU is not initialized. The Pre-Delivery Service (PDS) bulletin (link below) instructs technicians to perform this initialization after the D/C Cut Fuse is installed. The Repair Manual (links below) states that when any of the following conditions are met, the seat position information in the position control ECU assembly will be cleared: ?The power switch is turned off with any of the seat switches being operated and the ECU-DCC NO.2 fuse removed. ?The power switch is turned off within 1 second of any of the seat switches being operated with the ECU-DCC NO.2 fuse removed. ?Power supplied to the position control ECU assembly is cut while the seat is moving to the memorized position.
TSB001221Rev2
TSB: Some 2010 ? 2022 model year Toyota vehicles may exhibit paint stains after the removal of Rapgard?. The paint stains may appear to be under the clear coat but are usually under wrinkles in the Rapgard?. The wrinkles may trap water and cause the paint to stain from the trapped moisture, especially on horizontal surfaces such as the hood, roof, and trunk. Follow the Repair Procedure in this bulletin to address this condition
TSB008921Rev2
TSB: Some 2020 model year Camry, Camry Hybrid, Corolla Hatchback, RAV4, and RAV4 Hybrid vehicles may exhibit one or more of the following conditions: ?Diagnostic Trouble Code (DTC) B15A804 is present in current or history. ?Red SOS LED stays on after bulb check. ?Toyota App does not accept the activation code. ?Toyota App is inoperative. ?SOS call center does not receive the vehicle?s location in a timely manner. ?Toyota App shows an error 42 when trying to execute a command. ?Unable to remote start the vehicle with the key fob (if equipped). ?Unable to subscribe to remote services. ?Unable to activate Wi-Fi. ?Destination Assist is inoperative. Some 2020 ? 2021 model year Camry, Camry Hybrid, Corolla Hatchback, RAV4, and RAV4 Hybrid vehicles and some 2021 model year Avalon, Avalon Hybrid, Corolla, Corolla Hybrid, Sienna Hybrid, and Venza Hybrid vehicles may exhibit one or more of the following conditions: ?DTC B15A804 is present in current or history. ?Red SOS LED stays on after bulb check. ?Toyota App is inoperative. ?Unable to subscribe to remote services. ?Unable to activate Wi-Fi. ?Depleted 12V vehicle battery when in IG-OFF. ?Unable to reconnect out of network. A DCM reset and firmware update is now available to address these conditions. Follow the DCM Reset and Firmware Update Procedure in this bulletin to update the firmware.
T-SB-0110-20 Rev
TSB: This bulletin includes basic procedures for performing a rescue charge at battery on high voltage (HV) Ni-MH and Li-ion batteries. This bulletin should be used in conjunction with the applicable model and model year Repair Manual while performing the battery rescue charge. The GRX-5100 should be used wherever the Repair Manual references the Toyota Hybrid System (THS) charger
T-SB-0015-21 Rev
TSB: This Service Bulletin provides a procedure to properly perform the Techstream ?Control the Injection Mode? active test in some 2016 ? 2022 model year Toyota vehicles equipped with an FKS engine
TSB009421Rev1
TSB: Some 2005 ? 2022 model year Toyota vehicles that have undergone water intrusion may exhibit a condition in which a musty smell is present. Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this service bulletin is to provide general guidelines and procedures for odor remediation. This service bulletin provides a guide on how to prepare the interior of the vehicle prior to an odor remediation being performed, as well as contact information for an approved vendor who will arrange the remediation, and instructions on how to prepare the interior of the vehicle for reassembly once the remediation has been completed. Refer to all model and model year specific Repair Manuals and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines. This service bulletin is to provide a general overview and direction for the odor remediation process
TTT069522
TT: To improve customer support of telematics connected services features, additional resources have been provided in the Service Lane - Knowledge Center.
TSB008921Rev1
TSB: Some 2020 model year Camry, Camry Hybrid, Corolla Hatchback, RAV4, and RAV4 Hybrid vehicles may exhibit one or more of the following conditions: ?Diagnostic Trouble Code (DTC) B15A804 is present in current or history. ?Red SOS LED stays on after bulb check. ?Toyota App does not accept the activation code. ?Toyota App is inoperative. ?SOS call center does not receive the vehicle?s location in a timely manner. ?Toyota App shows an error 42 when trying to execute a command. ?Unable to remote start the vehicle with the key fob (if equipped). ?Unable to subscribe to remote services. ?Unable to activate Wi-Fi. ?Destination Assist is inoperative
TTT059920 Rev4
TT: Vehicle control apps might not operate as expected at times due to preconditions (normal operating parameters) not being established, vehicle settings and/or network/cellular coverage concerns
TSB003921
TSB: Hybrid vehicles are equipped with two types of batteries: ?Hybrid vehicle (HV) battery. ?Auxiliary (12V) battery. If the hybrid vehicle is put into storage, the State-Of-Charge (SOC) of its HV battery and auxiliary battery will gradually decrease. To prevent the auxiliary battery from becoming discharged during storage, proper maintenance is necessary. As a matter of policy, Toyota does not provide battery warranty coverage for discharged and/or failed batteries due to lack of maintenance. It is the dealer?s responsibility to maintain the specified SOC of the vehicle?s battery while in stock and ensure proper SOC at delivery. Perform the following maintenance service for the HV battery and auxiliary battery.
TTT069022
TT: On some 2021-2022MY Highlander HV, RAV4 HV, RAV4 Prime and Venza models, the connector cover for the Under Floor Wire Harness for the Rear Motor Generator may have the appearance of being damaged or missing
T-SB-0038-21 Obs
OBSOLETE NOTICE March 10, 2022: This bulletin is now obsolete. Please see T-SB-0015-22.
T-SB-0040-21 Obs
OBSOLETE NOTICE March 10, 2022: This bulletin is now obsolete. Please see T-SB-0016-22.
TSB001522
TSB: A battery in a stored vehicle is subject to conditions that can reduce its performance and service life. These conditions include storage period, temperature, parasitic drain, and battery load. Because of these factors, battery inspection and maintenance are required in order to ensure proper operation and optimal battery life. As a matter of policy, Toyota does not provide battery warranty coverage for discharged and/or failed batteries due to lack of maintenance. It is the dealer?s responsibility to maintain the specified State-Of-Charge (SOC) of the vehicle?s battery while in stock and ensure proper SOC at delivery. To eliminate customer service concerns due to an undercharged battery during the first few weeks of ownership, ALL dealers should test the auxiliary (12V) battery and recharge, if necessary, no more than 48 hours before delivery to the customer.
TSB001622
TSB: Long-term or off-site storage requires special care to keep vehicles factory fresh and ready for delivery. The following guidelines should be performed to minimize vehicle component/part degradation due to extended vehicle storage conditions. Long-term storage can affect a vehicle?s systems and components. Any problems that are found should be corrected immediately
T-TT-0687-22
TT: When customers have a concern about a discharged battery, no start, or general battery concern, the DCA-8000 is the only appropriate tool to use for diagnosis
T-SB-0012-22
TSB: 2022 model year Toyota vehicles are equipped with driver side floor mat retainers to secure the floor mat in the correct position. In addition, some models may also utilize retainers for passenger side and rear seat floor mats. During Pre-Delivery Service (PDS), follow the appropriate Installation Procedure to attach the driver side, and if applicable, the passenger side and rear seat floor mats to the vehicle carpet using the floor mat retainers. If installation instructions are included in the floor mat kit, place the instructions in the vehicle?s glove box for customer reference
T-SB-0035-21 Obs
OBSOLETE NOTICE March 04, 2022: This bulletin is now obsolete. Please see T-SB-0012-22.
T-TT-0599-20 Rev
TT: Vehicle control apps might not operate as expected at times due to preconditions (normal operating parameters) not being established, vehicle settings and/or network/cellular coverage concerns
T-SB-0084-21 Rev
TSB: Some 2019 ? 2022 model year RAV4 and RAV4 Hybrid and 2021 ? 2022 model year RAV4 Prime vehicles may exhibit a sloshing or splashing noise from inside one or more door panels when driving, opening and/or closing a door, and/or braking. This condition is caused by a cavity wax/debris/substance that may block door drain holes and restrict water from draining properly. Follow the Repair Procedure in this bulletin to address this condition
T-SB-0012-21 Rev
TSB: Some 2010 ? 2022 model year Toyota vehicles may exhibit paint stains after the removal of Rapgard?. The paint stains may appear to be under the clear coat but are usually under wrinkles in the Rapgard?. The wrinkles may trap water and cause the paint to stain from the trapped moisture, especially on horizontal surfaces such as the hood, roof, and trunk. Follow the Repair Procedure in this bulletin to address this condition
T-TT-0678-21
TT: Some 19CY LG DCM equipped vehicles may not be able to complete the firmware update due to not having an active account or waived services during the trial. Follow the steps below to enable ?Temp DCM Activation?.
T-SB-0104-21
TSB: Some 2018 ? 2022 model year Toyota vehicles equipped with an A25A-FKS, A25A-FXS, or M20A-FKS engine may exhibit one or more of the following conditions: ?Milky/Discolored engine oil. ?An ?Oil Pressure Low? warning message on the Multi-information Display (MID). ?A MIL ON condition with Diagnostic Trouble Codes (DTCs) P05202A (Engine Oil Pressure Sensor/Switch "A" Signal Stuck in Range) and/or P052477 (Engine Oil Pressure too low [Severe]). Moisture from blow-by gases condenses and accumulates in the engine oil during short trips in extreme cold weather. When the moisture in the oil freezes, the oil pressure may drop, and the aforementioned warning indicators may display. Follow the procedures in this bulletin to address these conditions.
T-SB-0100-21
TSB: Pre-Delivery Service (PDS) is a critical step in satisfying our new car customers. Customer feedback indicates the following areas deserve special attention when performing PDS: ?Careful inspection for paint chips/scratches and body dents/dings. ?Proper operation of electrical accessories (including interior light, clock, and radio reset). ?Interior cleanliness. ?Proper function of mechanical systems. Customer retention and proper maintenance of vehicles are and have always been a major focus for Toyota. To help remind customers that regular service is essential to the proper maintenance of the vehicle, dealers are required to install a service reminder sticker before delivery. By doing this, customers will be reminded to return to your dealership for service. Your current service reminder sticker may be used. (See PDS Check Sheet item 8 of ?Final Inspection and Cleaning.?) This bulletin contains the PDS procedures that apply specifically to 2022 model year RAV4, RAV4 Hybrid and RAV4 Prime vehicles. A universal PDS Check Sheet that contains PDS steps that apply to all 2022 model year Toyota vehicles has been developed. To properly perform a complete PDS, you must complete all procedures contained in this TSB as well as the universal PDS Check Sheet. In addition, if the vehicle is stored for over 30 days, be sure to follow Long-Term Vehicle Storage Guidelines.
T-SB-0094-21
TSB: Some 2005 ? 2022 model year Toyota vehicles that have undergone water intrusion may exhibit a condition in which a musty smell is present. Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this service bulletin is to provide general guidelines and procedures for odor remediation. This service bulletin provides a guide on how to prepare the interior of the vehicle prior to an odor remediation being performed, as well as contact information for an approved vendor who will arrange the remediation, and instructions on how to prepare the interior of the vehicle for reassembly once the remediation has been completed. Refer to all model and model year specific Repair Manuals and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines. This service bulletin is to provide a general overview and direction for the odor remediation process.
T-SB-0019-21 Rev
TSB: Some 2020 model year vehicles equipped with Audio Plus (version 1186) or earlier may exhibit one or more of the following conditions: ?WiFi intermittently inoperative. ?DTC (Diagnostic Trouble Code) B15DB present. ?Changing the Auto Relock Timer setting also changes the Remote 2-Press unlock setting. Some 2020 ? 2021 model year vehicles equipped with Audio Plus (version 1210), or Premium Audio (version 1196) or earlier may exhibit one or more of the following conditions: ?Intermittent screen flashing. ?Intermittent ?Destination Assist Unavailable? pop-up message. ?Intermittent blank screen. ?Bluetooth® intermittently disconnects. ?Abnormal radio playback after Destination Assist Call. ??There is no playable data? pop-up message when using USB Audio. ?Unable to answer phone calls when using Apple CarPlay®. ?Clock displays the incorrect time. ?Intermittent rebooting. ??The software version doesn?t correspond? pop-up is intermittently displayed. ?Intermittent black screen when using projection navigation. ?Abnormal noise after ACC OFF/ON when using AM mode and high volume. ??Please connect USB? pop-up message when USB is already connected. Some 2020 ? 2021 model year vehicles equipped with Audio Plus (version 1256), or Premium Audio (version 1256) or earlier may exhibit one or more of the following conditions: ?Navigation intermittently reverses its travel. ?Android AutoTM inoperative. ?Audio mode is set to ?Off? after disconnecting USB while using Apple CarPlay®. ?Intermittent black screen flash when connecting Bluetooth®. ?When the MAP button is pressed, a ?Navi app is not installed? pop-up is displayed. ?Intermittent black map screen on home screen. ?Bluetooth® intermittently disconnects. ?No outgoing voice when using Bluetooth® Handsfree for phone call. ?Bluetooth® Now Playing List song selection is slow. ?Unable to transfer phone contacts when using Bluetooth®.
T-SB-0037-21 Rev
TSB: An initialization procedure is required to activate the Entune? 3.0 App Suite Connect for Audio, Audio Plus, and Premium Audio head units before they are used for the first time on new vehicles. The initialization procedure may also be performed under other circumstances, such as following a head unit replacement or after the customer?s personal settings are erased. The initialization procedure requires between 3 and 15 minutes to complete, depending on file size, cellular connection speed, and other factors. Following the initialization procedure, individual Entune? 3.0 apps may periodically update through an over-the-air update system. Updates are either optional or mandatory. The update procedure will take approximately 1 minute for each app requiring an update. Follow the Initialization/Update Procedure in this bulletin to perform the initialization and app updates.
TTT067221
TT: Some 2021-2022 TMMK built vehicles with A25A-FKS/FXS engines may exhibit an oil leak from the No.2 Oil Pan. This issue is currently under investigation.
T-SB-0035-21 Rev
TSB: 2022 model year Toyota vehicles are equipped with driver side floor mat retainers to secure the floor mat in the correct position. In addition, some models may also utilize retainers for passenger side and rear seat floor mats. During Pre-Delivery Service (PDS), follow the appropriate Installation Procedure to attach the driver side, and if applicable, the passenger side and rear seat floor mats to the vehicle carpet using the floor mat retainers. If installation instructions are included in the floor mat kit, place the instructions in the vehicle?s glove box for customer reference.
T-SB-0038-21 Rev
TSB: A battery in a stored vehicle is subject to conditions that can reduce its performance and service life. These conditions include storage period, temperature, parasitic drain, and battery load. Because of these factors, battery inspection and maintenance are required in order to ensure proper operation and optimal battery life. As a matter of policy, Toyota does not provide battery warranty coverage for discharged and/or failed batteries due to lack of maintenance. It is the dealer?s responsibility to maintain the specified State-Of-Charge (SOC) of the vehicle?s battery while in stock and ensure proper SOC at delivery. To eliminate customer service concerns due to an undercharged battery during the first few weeks of ownership, ALL dealers should test the auxiliary (12V) battery and recharge, if necessary, no more than 48 hours before delivery to the customer.
T-SB-0040-21 Rev
TSB: Long-term or off-site storage requires special care to keep vehicles factory fresh and ready for delivery. The following guidelines should be performed to minimize vehicle component/part degradation due to extended vehicle storage conditions. Long-term storage can affect a vehicle?s systems and components. Any problems that are found should be corrected immediately.
T-SB-0084-21
TSB: Some 2019 ? 2022 model year RAV4 and RAV4 Hybrid, and 2021 ? 2022 model year RAV4 Prime vehicles may exhibit a sloshing or splashing noise from inside one or more door panels when driving, opening and/or closing a door, and/or braking. This condition is caused by a cavity wax/debris/substance that may block door drain holes and restrict water from draining properly. Follow the Repair Procedure in this bulletin to address this condition.
T-TT-0663-21
TT: When used in conjunction with the Repair Manual, these Blind Spot Monitor, Forward Recognition Camera, and Front Millimeter Wave Radar tips leverage SSTs and readily available tools to support target placement in varying shop environments.
Complaint counts are reports filed with NHTSA, not failure rates. A common model collects more of them than a rare one that breaks more often.