26TC03
Service Campaign
TECHNICAL INSTRUCTIONS FOR EMISSION NONCOMPLIANCE RECALL 26TC03 Certain 2022 – 2025 Model Year RAV4 Incorrect Mass Air Flow Sensor Reading
Vehicle report
Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
26TC03
TECHNICAL INSTRUCTIONS FOR EMISSION NONCOMPLIANCE RECALL 26TC03 Certain 2022 – 2025 Model Year RAV4 Incorrect Mass Air Flow Sensor Reading
T-SB-0029-26
A new head unit software update is available for 2023 – 2024 model year RAV4, RAV4 Hybrid, and RAV4 Prime vehicles equipped with Toyota Multimedia (earlier than version 1861). This software update includes the following improvements: • Usability of CarPlay® exit. • User Profile. • User interface. • Cloud navigation. • Intelligent assistant voice recognition. • Bug fixes.
T-SB-0023-26
Some customers may experience a rough running engine with a MIL ON P140018 DTC. Upon further inspection, a loose C90/C27 connector pin at the EGR valve may be found. To correct this concern, please reference the repair section of this TSB.
T-SB-0104-21 Rev2
OBSOLETE NOTICE February 27, 2026: This bulletin is no longer applicable and is now obsolete.
T-TT-0797-26
Some RAV4 vehicles power seat where the automatic seat adjustment by the memory function does not work.
T-SB-0055-24 Rev2
Some 2005 – 2026 Toyota vehicles that have undergone water intrusion may exhibit a condition in which a musty odor is present. Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this Service Bulletin is to provide general guidelines and procedures for odor remediation. This Service Bulletin provides a guide on how to prepare and treat the interior of the vehicle for odor remediation. Refer to the applicable model and model year Repair Manual and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines.
22TE09
Although the HV Floor Under Wire Harness and Rear Traction Motor Cable is covered by Toyota’s New Vehicle Limited Warranty for 3 years or 36,000 miles (whichever comes first), we at Toyota care about the customers’ ownership experience. Toyota is providing extended coverage under this Customer Support Program for repairs related to excessive corrosion to the wire harness connections at the Rear Motor Generator. Excessive corrosion can cause AM Radio Static during certain drive cycles, or the vehicle may not start.
T-SB-0010-24 Rev2
Some 2021 – 2022 model year Avalon, 2018 – 2024 Camry, 2019 – 2025 model year Corolla, 2022 – 2025 model year Corolla Cross, and 2019 – 2025 model year RAV4 vehicles with A25A-FKS and M20A-FKS engines may have a MIL ON condition with one or more of the following Diagnostic Trouble Codes (DTCs) upon cold soak start up with engine coolant temperatures between 14°F – 41°F: •P030027 – Random/Multiple Cylinder Misfire Detected (Emission) Signal Rate of Change Above Threshold •P030000 – Random/Multiple Cylinder Misfire Detected •P030100 – Cylinder 1 Misfire Detected •P030200 – Cylinder 2 Misfire Detected •P030300 – Cylinder 3 Misfire Detected •P030400 – Cylinder 4 Misfire Detected
T-SB-0058-23 Rev1
The air conditioning dye injection tool kit has been developed to aid in identifying the location of air conditioning refrigerant leaks. The procedures outlined in this Service Bulletin aid in locating, inspecting, and repairing refrigerant leaks.
T-TT-0779-25
To assist with the early detection and early resolution of audio related concerns you may be asked to recover MMR data from the head unit. The following steps are instructions on how to retrieve the data from the system and are only to be used when requested by FTS and/or FPE.
T-SB-0013-24 Rev1
The Immobilizer and Smart Key Reset is a feature that allows the registration of new keys when all master keys are lost. Once the system is reset, all previously registered keys will be erased and can never be reused. Another feature, Add/Remove Key, is also available. Once a key is removed, it can never be reused.
T-TT-0771-25
Some 2021-2025 MY Highlander HV, Sienna HV, RAV4, and RAV4 HV, may exhibit an oil leak from the area where the camshaft cover, camshaft housing, and the timing chain covers meet. This is typically seen on the exhaust side of the engine.
LSB006523
TT: Engine Oil Leak between the Lower Oil Pan and Crank Case
T-SB-0010-24 Rev1
Some 2021 – 2022 model year Avalon, 2018 – 2024 Camry, 2019 – 2025 model year Corolla, 2022 – 2025 model year Corolla Cross, and 2019 – 2025 model year RAV4 vehicles with A25A-FKS and M20A-FKS engines may have a MIL ON condition with one or more of the following Diagnostic Trouble Codes (DTCs) upon cold soak start up with engine coolant temperatures between 14°F – 41°F: •P030027 – Random/Multiple Cylinder Misfire Detected (Emission) Signal Rate of Change Above Threshold •P030000 – Random/Multiple Cylinder Misfire Detected •P030100 – Cylinder 1 Misfire Detected •P030200 – Cylinder 2 Misfire Detected •P030300 – Cylinder 3 Misfire Detected •P030400 – Cylinder 4 Misfire Detected
T-SB-0001-22 Rev2
Some 2019 – 2025 model year RAV4 and RAV4 Hybrid vehicles may exhibit a squeal/squeak noise from the front brakes with light to moderate braking.
T-SB-0035-24 Rev2
Acid rain results from rainwater or other airborne moisture that become acidic due to industrial chemical impurities in the atmosphere. If these acidic compounds settle on an exposed vehicle, especially the horizontal areas such as the hood, roof, and decklid, significant damage to the painted surfaces can occur. Acid rain damage can typically be identified on vehicles by the presence of stains on the paint surface that resemble hard water spots. Unlike water spots however, acid rain damage cannot be removed by regular washing procedures. Also, because acid rain can etch and soften the paint, normal buffing or polishing repair procedures should not be attempted. This can cause further damage and result in visible depressions in the paint surface. The following are the three major categories of acid rain damage: •Minor damage: requires only buffing to repair. •Moderate damage: usually requires neutralizing, color sanding, and buffing. •Severe damage: extending beyond 1/2 mil of clearcoat on a pearl, metallic, or solid color, requires neutralization, sanding, and repainting. In cases where acid rain damage is minor, neutralization and buffing with a liquid-type paint finessing product may provide an adequate repair. Only specially formulated products outlined in this bulletin should be used for that purpose. Unfortunately, other than minor damage, there is no simple method of determining the actual extent (depth) of acid penetration other than color sanding a representative affected area until there is no visible etching or depressions, followed by measuring the amount of paint removed with either a magnetic or digital-type film thickness gauge. The procedures in this bulletin are intended for use by qualified body/paint technicians and should not be attempted by inexperienced personnel. It is the dealer’s responsibility to protect and maintain the quality of the vehicle’s paint finish after receipt at the dealership prior to the first sale. Perform frequent vehicle washing, as often as daily, during high heat and humidity periods to minimize the potential for paint damage due to acid rain exposure. This is especially important in geographical areas known for high frequency and concentration of acid rain and industrial fallout.
T-SB-0038-24 Rev2
To prevent brake rotor rust from forming during transportation and storage, wheel film will be used instead of a cardboard type of anti-rust cover. The purpose of the wheel film is to shield the disc brake rotor from weather elements and initial rust before the vehicle is delivered to the customer. Consequently, the film should remain on the wheel for as long as possible.
T-SB-0039-24 Rev2
The condition known as acid rain is caused by airborne chemicals or particles in the atmosphere, which mix with rainwater, nighttime dew, or high humidity to form acidic compounds. If these contaminants settle and remain on a painted vehicle surface, especially the horizonal areas of the hood, roof, and decklid, significant damage can occur. This damage is the result of actual etching of the paint and appears as pitting or water spots. As acid rain droplets on the vehicle surface evaporate, the concentration strength of the acid increases, causing deeper and more rapid damage. This evaporation and corrosive action also occur more rapidly on dark colored cars as direct sun heat increases. It is the dealer’s responsibility to protect and maintain the quality of the vehicle’s paint finish after receipt at the dealership prior to the first sale. In areas known for high frequency and/or concentration of acid rain, frequent vehicle washing during high heat or humidity periods will minimize the potential for paint damage caused by acid rain. It is further recommended that either reverse osmosis or deionized water be used to prevent water spotting.
T-SB-0061-23 Rev2
Toyota vehicles are currently protected with RapgardTM protective film designed to protect the horizontal painted surfaces. This material protects from acid rain, environmental fallout, and rail contamination. Follow the Removal Procedure in this bulletin to remove the RapgardTM protective film within 90 days from initial application.
T-SB-0062-23 Rev2
Vehicles may occasionally be subjected to contamination by airborne iron particles shed from railroad tracks, train wheels, exposure to heavy machinery facilities, grinding, welding, etc. This type of contamination can be identified by the presence of small, red or brown particles on the paint surface. These particles are often difficult to see on dark color paints but can be easily felt when brushing a hand across horizontal body surfaces such as the hood, roof, or deck lid. Follow the Repair Procedure in this bulletin to clean vehicles that may have been subjected to contamination by airborne iron particles such as rail dust during rail transportation or extended storage near industrial areas.
T-TT-0768-24
Some technicians may report an engine oil leak from the Engine Oil Level Sensor area
23TJ01
The table below describes the phases currently planned for the Second Key Delivery Program and the estimated timing of announcement. This table will be updated during each phase launch and as more details become available.
T-TT-0764-24 Rev1
Customers may experience a MIL ON, or an intermittent MIL ON condition, accompanied by DTC P140018, Exhaust Gas Recirculation "A" Control Circuit 2 Circuit Current Below Threshold
T-SB-0098-24
Some 2022 model year Avalon and Avalon Hybrid, 2022 – 2024 model year Camry, Camry Hybrid, Corolla, Corolla Hatchback, Corolla Hybrid, Highlander, Highlander Hybrid, Prius, Prius Prime, RAV4, RAV4 Hybrid, RAV4 Prime, and Venza Hybrid, 2023 – 2024 model year Crown, and 2024 model year Grand Highlander vehicles may exhibit a high-pitched noise coming from the front HVAC blower motor while operating the air conditioner or heater. This condition does not affect the operation of the vehicle, however, a heater cover has been developed to help reduce or potentially eliminate the noise.
T-SB-0096-24
Some 2023 – 2024 model year Camry, Camry Hybrid, RAV4, and RAV4 Hybrid vehicles and 2024 model year Grand Highlander Hybrid vehicles equipped with an A25A-FKS or an A25A-FXS engine may exhibit an oil leak that originates between the oil pan sub-assembly and the stiffening crankcase assembly.
T-TT-0765-24
Some 2023-2024, Camry, Camry HV, Crown, RAV4, and RAV4 HV, may exhibit an oil leak from the cylinder head cover, near the union of the timing chain cover and cam housing.
T-SB-0062-24 Rev1
Some 2023 model year RAV4 Prime vehicles with Data Communication Module (DCM) firmware version earlier than LG-N210hh1V1V-09 may exhibit a condition in which the remote climate system is inoperative after the vehicle has been off for three hours or more. Some 2023 model year Corolla, Corolla Cross, Corolla Cross Hybrid, Corolla Hatchback, Corolla Hybrid, Crown, GR Corolla, Highlander, Highlander Hybrid, Prius, Prius Prime, RAV4, RAV4 Hybrid, RAV4 Prime, and Venza Hybrid vehicles and 2024 model year Grand Highlander and Grand Highlander Hybrid vehicles with DCM firmware versions earlier than LG-N210jj3333-09, LG-N210nn1212-09, LG-N310kk4646-0I, LG-N310ll4A4A-0I, LG-N310mm8A8A-0I, LG-N310nnBLBM-0I, or LG-N310oo1B1B-0I may exhibit a condition in which remote services are inoperative. Some 2023 model year Corolla, Corolla Cross, Corolla Cross Hybrid, Highlander, and Highlander Hybrid vehicles, 2023 – 2024 model year Corolla Hybrid, GR Corolla, Prius, Prius Prime, RAV4, RAV4 Hybrid, RAV4 Prime, and Venza Hybrid vehicles, 2024 model year Grand Highlander, Grand Highlander Hybrid, and Land Cruiser vehicles; 2023 – 2025 Corolla Hatchback and Crown vehicles, and 2025 Crown Signia vehicles with DCM firmware versions earlier than LG-N210qq####-## or LG-N310qq####-## may exhibit a condition in which Apple Music® or Amazon Music streaming and/or remote services are inoperative. A DCM firmware update is now available.
T-TT-0764-24
Customers may experience a MIL ON, or an intermittent MIL ON condition, accompanied by DTC P140018, Exhaust Gas Recirculation "A" Control Circuit 2 Circuit Current Below Threshold
T-TT-0763-24
P010012 or P010014 DTC sets after driving in the rain. DTC P010012/14 is currently under investigation.
T-TT-0751-24 Rev1
Some customers have expressed concern that the wireless functions of their Key Fob stop working. Key Fob LEDs will not turn ON, but engine starts with key held up against start button. Key battery voltage is confirmed OK and no DTC/RoB is found. This condition may occur if customer places Key Fob near wireless charger while phone is charging. When the key battery is removed and reinstalled, the Key Fob begins to operate normally.
T-SB-0055-24 Rev1
Some 2005 – 2024 Toyota vehicles that have undergone water intrusion may exhibit a condition in which a musty odor is present. Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this Service Bulletin is to provide general guidelines and procedures for odor remediation. This Service Bulletin provides a guide on how to prepare and treat the interior of the vehicle for odor remediation. Refer to the applicable model and model year Repair Manual and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines. This Service Bulletin is to provide a general overview and direction for the odor remediation process.
T-SB-0027-24 Rev1
OBSOLETE NOTICE July 18, 2024: This bulletin is now obsolete. Please see T-SB-0062-24.
T-SB-0062-24
Some 2023 model year RAV4 Prime vehicles with Data Communication Module (DCM) firmware version earlier than LG-N210hh1V1V-09 may exhibit a condition in which the remote climate system is inoperative after the vehicle has been off for three hours or more. Some 2023 model year Corolla, Corolla Cross, Corolla Cross Hybrid, Corolla Hatchback, Corolla Hybrid, Crown, GR Corolla, Highlander, Highlander Hybrid, Prius, Prius Prime, RAV4, RAV4 Hybrid, RAV4 Prime, and Venza Hybrid vehicles and 2024 model year Grand Highlander, and Grand Highlander Hybrid vehicles with previous versions of DCM firmware (see Table 1 below) may exhibit a condition in which remote services are inoperative. A DCM firmware update is now available to address this condition.
T-SB-0035-24 Rev1
Acid rain results from rainwater or other airborne moisture that become acidic due to industrial chemical impurities in the atmosphere. If these acidic compounds settle on an exposed vehicle, especially the horizontal areas such as the hood, roof, and decklid, significant damage to the painted surfaces can occur. Acid rain damage can typically be identified on vehicles by the presence of stains on the paint surface that resemble hard water spots. Unlike water spots however, acid rain damage cannot be removed by regular washing procedures. Also, because acid rain can etch and soften the paint, normal buffing or polishing repair procedures should not be attempted. This can cause further damage and result in visible depressions in the paint surface. The following are the three major categories of acid rain damage: •Minor damage: requires only buffing to repair. •Moderate damage: usually requires neutralizing, color sanding, and buffing. •Severe damage: extending beyond 1/2 mil of clearcoat on a pearl, metallic, or solid color, requires neutralization, sanding, and repainting. In cases where acid rain damage is minor, neutralization and buffing with a liquid-type paint finessing product may provide an adequate repair. Only specially formulated products outlined in this bulletin should be used for that purpose. Unfortunately, other than minor damage, there is no simple method of determining the actual extent (depth) of acid penetration other than color sanding a representative affected area until there is no visible etching or depressions, followed by measuring the amount of paint removed with either a magnetic or digital-type film thickness gauge. The procedures in this bulletin are intended for use by qualified body/paint technicians and should not be attempted by inexperienced personnel. It is the dealer’s responsibility to protect and maintain the quality of the vehicle’s paint finish after receipt at the dealership prior to the first sale. Perform frequent vehicle washing, as often as daily, during high heat and humidity periods to minimize the potential for paint damage due to acid rain exposure. This is especially important in geographical areas known for high frequency and concentration of acid rain and industrial fallout.
T-SB-0038-24 Rev1
To prevent brake rotor rust from forming during transportation and storage, wheel film will be used instead of a cardboard type of anti-rust cover. The purpose of the wheel film is to shield the disc brake rotor from weather elements and initial rust before the vehicle is delivered to the customer. Consequently, the film should remain on the wheel for as long as possible.
T-SB-0039-24 Rev1
The condition known as acid rain is caused by airborne chemicals or particles in the atmosphere, which mix with rainwater, nighttime dew, or high humidity to form acidic compounds. If these contaminants settle and remain on a painted vehicle surface, especially the horizonal areas of the hood, roof, and decklid, significant damage can occur. This damage is the result of actual etching of the paint and appears as pitting or water spots. As acid rain droplets on the vehicle surface evaporate, the concentration strength of the acid increases, causing deeper and more rapid damage. This evaporation and corrosive action also occur more rapidly on dark colored cars as direct sun heat increases. It is the dealer’s responsibility to protect and maintain the quality of the vehicle’s paint finish after receipt at the dealership prior to the first sale. In areas known for high frequency and/or concentration of acid rain (see Figure 1), frequent vehicle washing during high heat or humidity periods will minimize the potential for paint damage caused by acid rain. It is further recommended that either reverse osmosis or deionized water be used to prevent water spotting.
T-SB-0055-24
Some 2005 – 2024 Toyota vehicles that have undergone water intrusion may exhibit a condition in which a musty odor is present. Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this Service Bulletin is to provide general guidelines and procedures for odor remediation. This Service Bulletin provides a guide on how to prepare and treat the interior of the vehicle for odor remediation. Refer to the applicable model and model year Repair Manual and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines.
T-SB-0103-20 Rev1
This Service Bulletin provides updated non-electric water pump leak inspection and diagnostic tips for some 2008 – 2025 model year Toyota vehicles.
24TC03
TECHNICAL INSTRUCTIONS FOR SPECIAL SERVICE CAMPAIGN 24TC03 DATA COMMUNICATON MODULE (DCM) UPDATE CERTAIN 2023 COROLLA, COROLLA CROSS, COROLLA HATCHBACK, COROLLA HV, GR COROLLA, CROWN, HIGHLANDER, HIGHLANDER HV, PRIUS, RAV4, RAV4 PRIME, RAV4 HV, VENZA HV
T-SB-0061-23 Rev1
Toyota vehicles are currently protected with RapgardTM protective film designed to protect the horizontal painted surfaces. This material protects from acid rain, environmental fallout, and rail contamination.
T-SB-0062-23 Rev1
Vehicles may occasionally be subjected to contamination by airborne iron particles shed from railroad tracks, train wheels, exposure to heavy machinery facilities, grinding, welding, etc. This type of contamination can be identified by the presence of small, red or brown particles on the paint surface. These particles are often difficult to see on dark color paints but can be easily felt when brushing a hand across horizontal body surfaces such as the hood, roof, or deck lid.
T-SB-0035-24
Acid rain results from rainwater or other airborne moisture that become acidic due to industrial chemical impurities in the atmosphere. If these acidic compounds settle on an exposed vehicle, especially the horizontal areas such as the hood, roof, and decklid, significant damage to the painted surfaces can occur. Acid rain damage can typically be identified on vehicles by the presence of stains on the paint surface that resemble hard water spots. Unlike water spots however, acid rain damage cannot be removed by regular washing procedures. Also, because acid rain can etch and soften the paint, normal buffing or polishing repair procedures should not be attempted. This can cause further damage and result in visible depressions in the paint surface. The following are the three major categories of acid rain damage: •Minor damage: requires only buffing to repair. •Moderate damage: usually requires neutralizing, color sanding, and buffing. •Severe damage: extending beyond 1/2 mil of clearcoat on a pearl, metallic, or solid color, requires neutralization, sanding, and repainting. In cases where acid rain damage is minor, neutralization and buffing with a liquid-type paint finessing product may provide an adequate repair. Only specially formulated products outlined in this bulletin should be used for that purpose. Unfortunately, other than minor damage, there is no simple method of determining the actual extent (depth) of acid penetration other than color sanding a representative affected area until there is no visible etching or depressions, followed by measuring the amount of paint removed with either a magnetic or digital-type film thickness gauge. The procedures in this bulletin are intended for use by qualified body/paint technicians and should not be attempted by inexperienced personnel. While the quality and durability of paint on Toyota vehicles is continuously being improved, it remains the dealer’s responsibility to protect and maintain the quality of the vehicle’s paint finish after receipt at the dealership prior to the first sale. To read, While the quality and durability of paint on Toyota vehicles is continuously being improved, it remains the dealer’s responsibility to protect and maintain the quality of the vehicle’s paint finish after receipt at the dealership prior to first sale. Perform frequent vehicle washing, as often as daily, during high heat and humidity periods to minimize the potential for paint damage due to acid rain exposure. This is especially important in geographical areas known for high frequency and concentration of acid rain and industrial fallout.
T-SB-0038-24
To prevent brake rotor rust from forming during transportation and storage, wheel film will be used instead of a cardboard type of anti-rust cover. The purpose of the wheel film is to shield the disc brake rotor from weather elements and initial rust before the vehicle is delivered to the customer. Consequently, the film should remain on the wheel for as long as possible. SUPERSESSION NOTICE The information contained in this bulletin supersedes Service Bulletin No. PD017-04. •The entire bulletin has been updated.
T-SB-0039-24
The condition known as acid rain is caused by airborne chemicals or particles in the atmosphere, which mix with rainwater, nighttime dew, or high humidity to form acidic compounds. If these contaminants settle and remain on a painted vehicle surface, especially the horizonal areas of the hood, roof, and decklid, significant damage can occur. This damage is the result of actual etching of the paint and appears as pitting or water spots. As acid rain droplets on the vehicle surface evaporate, the concentration strength of the acid increases, causing deeper and more rapid damage. This evaporation and corrosive action also occur more rapidly on dark colored cars as direct sun heat increases. While Toyota paint quality, durability, and resistance to environmental factors is continuously being improved, it remains the responsibility of the dealer to protect and maintain the vehicle’s paint finish from the time of arrival at the dealership until retail delivery to the customer. In areas known for high frequency and/or concentration of acid rain (see Figure 1), frequent vehicle washing during high heat or humidity periods will minimize the potential for paint damage caused by acid rain. It is further recommended that either reverse osmosis or deionized water be used to prevent water spotting.
23TJ01 Eligibility
The table describes the phases currently planned for the Second Key Delivery Program and the estimated timing of announcement. This table will be updated during each phase launch and as more details become available.
T-TT-0754-24
Customers have expressed concerns about the performance of Qi Wireless Chargers. Wireless chargers on applicable vehicles are designed to work with Qi Certified devices only. MagSafe devices, that are not Qi Certified, may not charge as expected with Qi Wireless Chargers.
23TJ01_P5_Dealer
DP: The subject vehicles were delivered with only one (1) Smart Key on select models since October 2022 due to a global semiconductor shortage impacting certain microchips. The affected vehicles were delivered with one (1) Smart Key and a second mechanical key.
Toyota Second Ke
The table describes the phases currently planned for the Second Key Delivery Program and the estimated timing of announcement. This table will be updated during each phase launch and as more details become available.
T-PANT-2024-004-
This is to advise of various price adjustments that will affect Toyota Genuine Motor Oil and Long Life Coolant, effective March 1, 2024. These products are ordered through the Toyota Complete Maintenance Care (TCMC) website.
T-SB-0013-24
TSB: The Immobilizer and Smart Key Reset is a feature that allows the registration of new keys when all master keys are lost. Once the system is reset, all previously registered keys will be erased and can never be reused. Another feature, Add/Remove Key, is also available. Once a key is removed, it can never be reused.
23TJ01 Current P
The table describes the phases currently planned for the Second Key Delivery Program and the estimated timing of announcement. This table will be updated during each phase launch and as more details become available.
TSB001024
TSB: Some 2021 ? 2022 model year Avalon, 2018 ? 2024 Camry, and 2019 ? 2024 RAV4 vehicles with A25A-FKS engines may have a MIL ON condition with one or more of the following Diagnostic Trouble Codes (DTCs) upon cold soak start up with engine coolant temperatures between 14°F ? 41°F: ?P030027 ? Random/Multiple Cylinder Misfire Detected (Emission) Signal Rate of Change Above Threshold ?P030000 ? Random/Multiple Cylinder Misfire Detected ?P030100 ? Cylinder 1 Misfire Detected ?P030200 ? Cylinder 2 Misfire Detected ?P030300 ? Cylinder 3 Misfire Detected ?P030400 ? Cylinder 4 Misfire Detected Follow the Repair Procedure in this bulletin to address these conditions.
TSB010421
TSB: Some 2018 ? 2024 model year Toyota vehicles equipped with an A25A-FKS, A25A-FXS, M20A-FKS, or M20A-FXS engine may exhibit one or more of the following conditions: ?Milky/discolored engine oil. ?An ?Oil Pressure Low? warning message on the Multi-information Display (MID). ?A MIL ON condition with Diagnostic Trouble Codes (DTCs) P05202A (Engine Oil Pressure Sensor/Switch ?A? Signal Stuck in Range) and/or P052477 (Engine Oil Pressure Too Low [Severe]) present. Moisture from blow-by gases condenses and accumulates in the engine oil during short trips in extreme cold weather. When the moisture in the oil freezes, the oil pressure may drop, and the aforementioned warning indicators may display. Follow the procedures in this bulletin to address these conditions.
23TJ01A
DP: The subject vehicles were delivered with only one (1) Smart Key on select models since October 2022 due to a global semiconductor shortage impacting certain microchips. The affected vehicles were delivered with one (1) Smart Key and a second mechanical key.
23TJ01P4B
RL: The supply of Smart Keys available for Toyota vehicles has been temporarily limited to one (1) on select models since October 2022 due to global semiconductor shortages impacting certain microchips. Affected vehicles have been delivered with only one Smart Key and a second mechanical key.
23TJ01P4C
TI: TECHNICAL INSTRUCTIONS FOR 23TJ01 Second Key Delivery Program Multiple Models and Model Years
23LJ01a
RL: The supply of Smart Keys available for Toyota vehicles has been temporarily limited to one (1) on select models since October 2022 due to global semiconductor shortages impacting certain microchips. Affected vehicles have been delivered with only one Smart Key and a second mechanical key.
23TJ01b
TI: TECHNICAL INSTRUCTIONS FOR 23TJ01 Second Key Delivery Program Multiple Models and Model Years
TSB005823
TSB: The air conditioning dye injection tool kit has been developed to aid in identifying the location of air conditioning refrigerant leaks. Follow the procedures outlined in this service bulletin to aid in locating, inspecting, and repairing refrigerant leaks
TSB003220
TSB: Replacement certification labels (the vinyl label installed on the driver door or door post) and VIN plates (the metal plate riveted to dashboard) (see Figure 1) for most 1979 ? 2023 model year vehicles may be available provided the requests meet the criteria listed in this Service Bulletin. Follow the Procurement Procedure in this bulletin to request a replacement certification label or VIN plate.
TTT073723
TT: A very small percentage of customers experience operational difficulties with some telematics features which they cannot resolve on their own. These resources, in conjunction with the Repair Manual, are for dealership personnel to assist those customers with user issues, user errors, and compatibility issues with other vehicle systems and external applications encountered while operating telematics features. Toyota has developed and provided the following Telematics Diagnostic Guide to assist dealer technicians.
T-TT-0726-23
TT: Some 2021 - 2023 Highlander HV, RAV4 HV and Sienna HV vehicles equipped with Rear Motor Generator, MGR (Q610), may duplicate an abnormal noise (Drone, Growl, Humming, and/or other) from the MGR at various vehicle speeds and normal drive conditions. Please contact TAS for diagnostic instructions to aid in resolution of the condition.
T-TT-0728-23
TT: This issue is currently under investigation. Please create TAS case and attach a store all health check. Please contact TAS for further instructions. If it is a weekend or a holiday, continue with diagnosis and repair. Please save all parts/ or details and contact TAS on the next available workday.
T-SB-0042-23
TSB: Some 2023 ? 2024 model year Toyota vehicles use hub bolts in place of studs/nuts to fasten the wheels to the vehicle. If non-compatible wheels or hub bolts/nuts are installed, there is increased risk that the wheel(s) could come off resulting in a crash. This service bulletin outlines the physical differences and precautions that should be taken when servicing different wheel and wheel fastener types.
TSB-0041-23
TSB: Some 2023 model year GR Corolla, RAV4, RAV4 Hybrid, RAV4 Prime, and Venza Hybrid vehicles with multimedia version older than 1564 may exhibit one or more of the following conditions: ?Head unit rebooting (does not affect backup camera). ?Head unit does not boot up (does not affect backup camera). ?Display screen flickers (does not affect backup camera). ?Map is not displayed. ?User profile enhancements. ?The French ?Share ETA? screen is not completely in French. ?Incoming call ringing continues even after ignoring or ending the call. Some 2023 model year Prius and Prius Prime vehicles with multimedia version older than 1586 may exhibit one or more of the following conditions: ?Head unit rebooting (does not affect backup camera). ?Head unit does not boot up (does not affect backup camera). ?Display screen flickers (does not affect backup camera). A software update is now available to address these conditions
23TJ01-1
RL: The supply of Smart Keys available for Toyota vehicles has been temporarily limited to one (1) on select models since October 2022 due to global semiconductor shortages impacting certain microchips. Affected vehicles have been delivered with only one Smart Key and a second mechanical key.
23TJ01-2
TI: TECHNICAL INSTRUCTIONS FOR 23TJ01 Second Key Delivery Program
TSB-0033-23
TSB: Some 2020 ? 2023 model year Highlander Hybrid and 2021 ? 2023 model year RAV4 Hybrid, RAV4 Prime, Sienna Hybrid, and Venza Hybrid vehicles may exhibit a MIL ON condition with one or both of the following Diagnostic Trouble Codes (DTCs) present: ?P24517F ? Evaporative Emission System Switching Valve Actuator Stuck Off. ?P14502A ? Fuel Tank Pressure Sensor Signal Stuck in Range.
T-TT-0734-23
TT: When setting up the Toyota Audio Multimedia (21MM) user profile, if the QR code is not working please use the following recommendations.
T-TT-0733-23
TT: Some 2022-2024 MY vehicles equipped with the A25A engine may exhibit a leak from the engine water pump, and/or MIL On condition accompanied by DTC(s): ?P26CA14 Engine Coolant Pump Circuit Short to Ground or Open ?P26CA31 Engine Coolant Pump No Signal
T-TT-0699-22 Rev
TT: Some Model Year 2018-2023 vehicles equipped with A25A-FKS/FXS or M20A-FKS/FXS engines may display the following message ?Engine Maintenance Required Visit Your Dealer? on the combination meter
T-TT-0723-23
TT: Some 2021 to 2023 MY vehicles equipped Rear Motor Generator, MGR (Q610) may experience an oil leak concern. This issue is currently under investigation
TTT071522
TT: Some 2019- 2023 RAV4 HV vehicles may duplicate an abnormal noise (Growl, Humming and/or other) from the Hybrid T/A and/or MGR at various vehicle speeds and normal drive conditions
T-SB-0001-22 Rev
TSB: Some 2019 ? 2023 model year RAV4 and RAV4 Hybrid vehicles may exhibit a squeal/squeak noise from the front brakes with light to moderate braking. Follow the Repair Procedure in this bulletin to address this condition
Complaint counts are reports filed with NHTSA, not failure rates. A common model collects more of them than a rare one that breaks more often.