Vehicle report
Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
22TD04
22TD04 Expired on June 30, 2025 TECHNICAL INSTRUCTIONS FOR LIMITED SERVICE CAMPAIGN 22TD04 ACCESSORY DASH CAMERA FIRMWARE UPDATE CERTAIN 2021 MODEL YEAR SIENNA VEHICLES CERTAIN 2021 MODEL YEAR VENZA VEHICLES
LSB006523
TT: Engine Oil Leak between the Lower Oil Pan and Crank Case
T-SB-0035-24 Rev2
Acid rain results from rainwater or other airborne moisture that become acidic due to industrial chemical impurities in the atmosphere. If these acidic compounds settle on an exposed vehicle, especially the horizontal areas such as the hood, roof, and decklid, significant damage to the painted surfaces can occur. Acid rain damage can typically be identified on vehicles by the presence of stains on the paint surface that resemble hard water spots. Unlike water spots however, acid rain damage cannot be removed by regular washing procedures. Also, because acid rain can etch and soften the paint, normal buffing or polishing repair procedures should not be attempted. This can cause further damage and result in visible depressions in the paint surface. The following are the three major categories of acid rain damage: •Minor damage: requires only buffing to repair. •Moderate damage: usually requires neutralizing, color sanding, and buffing. •Severe damage: extending beyond 1/2 mil of clearcoat on a pearl, metallic, or solid color, requires neutralization, sanding, and repainting. In cases where acid rain damage is minor, neutralization and buffing with a liquid-type paint finessing product may provide an adequate repair. Only specially formulated products outlined in this bulletin should be used for that purpose. Unfortunately, other than minor damage, there is no simple method of determining the actual extent (depth) of acid penetration other than color sanding a representative affected area until there is no visible etching or depressions, followed by measuring the amount of paint removed with either a magnetic or digital-type film thickness gauge. The procedures in this bulletin are intended for use by qualified body/paint technicians and should not be attempted by inexperienced personnel. It is the dealer’s responsibility to protect and maintain the quality of the vehicle’s paint finish after receipt at the dealership prior to the first sale. Perform frequent vehicle washing, as often as daily, during high heat and humidity periods to minimize the potential for paint damage due to acid rain exposure. This is especially important in geographical areas known for high frequency and concentration of acid rain and industrial fallout.
T-SB-0038-24 Rev2
To prevent brake rotor rust from forming during transportation and storage, wheel film will be used instead of a cardboard type of anti-rust cover. The purpose of the wheel film is to shield the disc brake rotor from weather elements and initial rust before the vehicle is delivered to the customer. Consequently, the film should remain on the wheel for as long as possible.
T-SB-0039-24 Rev2
The condition known as acid rain is caused by airborne chemicals or particles in the atmosphere, which mix with rainwater, nighttime dew, or high humidity to form acidic compounds. If these contaminants settle and remain on a painted vehicle surface, especially the horizonal areas of the hood, roof, and decklid, significant damage can occur. This damage is the result of actual etching of the paint and appears as pitting or water spots. As acid rain droplets on the vehicle surface evaporate, the concentration strength of the acid increases, causing deeper and more rapid damage. This evaporation and corrosive action also occur more rapidly on dark colored cars as direct sun heat increases. It is the dealer’s responsibility to protect and maintain the quality of the vehicle’s paint finish after receipt at the dealership prior to the first sale. In areas known for high frequency and/or concentration of acid rain, frequent vehicle washing during high heat or humidity periods will minimize the potential for paint damage caused by acid rain. It is further recommended that either reverse osmosis or deionized water be used to prevent water spotting.
T-SB-0061-23 Rev2
Toyota vehicles are currently protected with RapgardTM protective film designed to protect the horizontal painted surfaces. This material protects from acid rain, environmental fallout, and rail contamination. Follow the Removal Procedure in this bulletin to remove the RapgardTM protective film within 90 days from initial application.
T-SB-0062-23 Rev2
Vehicles may occasionally be subjected to contamination by airborne iron particles shed from railroad tracks, train wheels, exposure to heavy machinery facilities, grinding, welding, etc. This type of contamination can be identified by the presence of small, red or brown particles on the paint surface. These particles are often difficult to see on dark color paints but can be easily felt when brushing a hand across horizontal body surfaces such as the hood, roof, or deck lid. Follow the Repair Procedure in this bulletin to clean vehicles that may have been subjected to contamination by airborne iron particles such as rail dust during rail transportation or extended storage near industrial areas.
T-SB-0055-24 Rev1
Some 2005 – 2024 Toyota vehicles that have undergone water intrusion may exhibit a condition in which a musty odor is present. Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this Service Bulletin is to provide general guidelines and procedures for odor remediation. This Service Bulletin provides a guide on how to prepare and treat the interior of the vehicle for odor remediation. Refer to the applicable model and model year Repair Manual and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines. This Service Bulletin is to provide a general overview and direction for the odor remediation process.
T-SB-0035-24 Rev1
Acid rain results from rainwater or other airborne moisture that become acidic due to industrial chemical impurities in the atmosphere. If these acidic compounds settle on an exposed vehicle, especially the horizontal areas such as the hood, roof, and decklid, significant damage to the painted surfaces can occur. Acid rain damage can typically be identified on vehicles by the presence of stains on the paint surface that resemble hard water spots. Unlike water spots however, acid rain damage cannot be removed by regular washing procedures. Also, because acid rain can etch and soften the paint, normal buffing or polishing repair procedures should not be attempted. This can cause further damage and result in visible depressions in the paint surface. The following are the three major categories of acid rain damage: •Minor damage: requires only buffing to repair. •Moderate damage: usually requires neutralizing, color sanding, and buffing. •Severe damage: extending beyond 1/2 mil of clearcoat on a pearl, metallic, or solid color, requires neutralization, sanding, and repainting. In cases where acid rain damage is minor, neutralization and buffing with a liquid-type paint finessing product may provide an adequate repair. Only specially formulated products outlined in this bulletin should be used for that purpose. Unfortunately, other than minor damage, there is no simple method of determining the actual extent (depth) of acid penetration other than color sanding a representative affected area until there is no visible etching or depressions, followed by measuring the amount of paint removed with either a magnetic or digital-type film thickness gauge. The procedures in this bulletin are intended for use by qualified body/paint technicians and should not be attempted by inexperienced personnel. It is the dealer’s responsibility to protect and maintain the quality of the vehicle’s paint finish after receipt at the dealership prior to the first sale. Perform frequent vehicle washing, as often as daily, during high heat and humidity periods to minimize the potential for paint damage due to acid rain exposure. This is especially important in geographical areas known for high frequency and concentration of acid rain and industrial fallout.
T-SB-0038-24 Rev1
To prevent brake rotor rust from forming during transportation and storage, wheel film will be used instead of a cardboard type of anti-rust cover. The purpose of the wheel film is to shield the disc brake rotor from weather elements and initial rust before the vehicle is delivered to the customer. Consequently, the film should remain on the wheel for as long as possible.
T-SB-0039-24 Rev1
The condition known as acid rain is caused by airborne chemicals or particles in the atmosphere, which mix with rainwater, nighttime dew, or high humidity to form acidic compounds. If these contaminants settle and remain on a painted vehicle surface, especially the horizonal areas of the hood, roof, and decklid, significant damage can occur. This damage is the result of actual etching of the paint and appears as pitting or water spots. As acid rain droplets on the vehicle surface evaporate, the concentration strength of the acid increases, causing deeper and more rapid damage. This evaporation and corrosive action also occur more rapidly on dark colored cars as direct sun heat increases. It is the dealer’s responsibility to protect and maintain the quality of the vehicle’s paint finish after receipt at the dealership prior to the first sale. In areas known for high frequency and/or concentration of acid rain (see Figure 1), frequent vehicle washing during high heat or humidity periods will minimize the potential for paint damage caused by acid rain. It is further recommended that either reverse osmosis or deionized water be used to prevent water spotting.
T-SB-0055-24
Some 2005 – 2024 Toyota vehicles that have undergone water intrusion may exhibit a condition in which a musty odor is present. Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this Service Bulletin is to provide general guidelines and procedures for odor remediation. This Service Bulletin provides a guide on how to prepare and treat the interior of the vehicle for odor remediation. Refer to the applicable model and model year Repair Manual and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines.
T-SB-0061-23 Rev1
Toyota vehicles are currently protected with RapgardTM protective film designed to protect the horizontal painted surfaces. This material protects from acid rain, environmental fallout, and rail contamination.
T-SB-0062-23 Rev1
Vehicles may occasionally be subjected to contamination by airborne iron particles shed from railroad tracks, train wheels, exposure to heavy machinery facilities, grinding, welding, etc. This type of contamination can be identified by the presence of small, red or brown particles on the paint surface. These particles are often difficult to see on dark color paints but can be easily felt when brushing a hand across horizontal body surfaces such as the hood, roof, or deck lid.
T-SB-0035-24
Acid rain results from rainwater or other airborne moisture that become acidic due to industrial chemical impurities in the atmosphere. If these acidic compounds settle on an exposed vehicle, especially the horizontal areas such as the hood, roof, and decklid, significant damage to the painted surfaces can occur. Acid rain damage can typically be identified on vehicles by the presence of stains on the paint surface that resemble hard water spots. Unlike water spots however, acid rain damage cannot be removed by regular washing procedures. Also, because acid rain can etch and soften the paint, normal buffing or polishing repair procedures should not be attempted. This can cause further damage and result in visible depressions in the paint surface. The following are the three major categories of acid rain damage: •Minor damage: requires only buffing to repair. •Moderate damage: usually requires neutralizing, color sanding, and buffing. •Severe damage: extending beyond 1/2 mil of clearcoat on a pearl, metallic, or solid color, requires neutralization, sanding, and repainting. In cases where acid rain damage is minor, neutralization and buffing with a liquid-type paint finessing product may provide an adequate repair. Only specially formulated products outlined in this bulletin should be used for that purpose. Unfortunately, other than minor damage, there is no simple method of determining the actual extent (depth) of acid penetration other than color sanding a representative affected area until there is no visible etching or depressions, followed by measuring the amount of paint removed with either a magnetic or digital-type film thickness gauge. The procedures in this bulletin are intended for use by qualified body/paint technicians and should not be attempted by inexperienced personnel. While the quality and durability of paint on Toyota vehicles is continuously being improved, it remains the dealer’s responsibility to protect and maintain the quality of the vehicle’s paint finish after receipt at the dealership prior to the first sale. To read, While the quality and durability of paint on Toyota vehicles is continuously being improved, it remains the dealer’s responsibility to protect and maintain the quality of the vehicle’s paint finish after receipt at the dealership prior to first sale. Perform frequent vehicle washing, as often as daily, during high heat and humidity periods to minimize the potential for paint damage due to acid rain exposure. This is especially important in geographical areas known for high frequency and concentration of acid rain and industrial fallout.
T-SB-0038-24
To prevent brake rotor rust from forming during transportation and storage, wheel film will be used instead of a cardboard type of anti-rust cover. The purpose of the wheel film is to shield the disc brake rotor from weather elements and initial rust before the vehicle is delivered to the customer. Consequently, the film should remain on the wheel for as long as possible. SUPERSESSION NOTICE The information contained in this bulletin supersedes Service Bulletin No. PD017-04. •The entire bulletin has been updated.
T-SB-0039-24
The condition known as acid rain is caused by airborne chemicals or particles in the atmosphere, which mix with rainwater, nighttime dew, or high humidity to form acidic compounds. If these contaminants settle and remain on a painted vehicle surface, especially the horizonal areas of the hood, roof, and decklid, significant damage can occur. This damage is the result of actual etching of the paint and appears as pitting or water spots. As acid rain droplets on the vehicle surface evaporate, the concentration strength of the acid increases, causing deeper and more rapid damage. This evaporation and corrosive action also occur more rapidly on dark colored cars as direct sun heat increases. While Toyota paint quality, durability, and resistance to environmental factors is continuously being improved, it remains the responsibility of the dealer to protect and maintain the vehicle’s paint finish from the time of arrival at the dealership until retail delivery to the customer. In areas known for high frequency and/or concentration of acid rain (see Figure 1), frequent vehicle washing during high heat or humidity periods will minimize the potential for paint damage caused by acid rain. It is further recommended that either reverse osmosis or deionized water be used to prevent water spotting.
T-PANT-2024-004-
This is to advise of various price adjustments that will affect Toyota Genuine Motor Oil and Long Life Coolant, effective March 1, 2024. These products are ordered through the Toyota Complete Maintenance Care (TCMC) website.
TSB010622
TSB: Some 2018 ? 2022 model year Toyota vehicles equipped with a Premium Audio with Dynamic Navigation System require a Special Service Tool (SST) USB flash drive to update the map, points of interest, and system software. The SST is used with applicable vehicles to deliver the update, however, the process for generating license keys differs from previous generations. Before attempting to perform a map update, the expiration date of the dynamic subscription (stored in the head unit), must be checked. If the expiration date has not passed, a license key may be generated without the purchase of an Activation Card Number (ACN). Updating the map without the use of an ACN is considered an Embedded Navigation Update (refer to pg. 10) and performing this update does not extend the subscription to dynamic map services. If the subscription period has expired, or is expiring within the next 90 days, it should be recommended to the customer to purchase an ACN. Utilizing an ACN, will initiate the Dynamic Navigation Update (refer to pg. 4). This Dynamic Navigation Update will perform the embedded navigation update and provide dynamic map services for a period of two years from the date that the Dynamic Navigation Update is performed. ACNs are provided in a pamphlet available through the normal parts ordering system. Follow the process in this bulletin to perform the update.
TSB001823
TSB: Some 2021 ? 2023 model year Sienna Hybrid vehicles may exhibit a MIL ON condition with Diagnostic Trouble Code (DTC) P060694 (Hybrid/EV Powertrain Control Module Processor Unexpected Operation) present. The Hybrid Vehicle Control Computer logic has been modified to reduce the possibility of this DTC setting incorrectly. Follow the Repair Procedure in this bulletin to address this condition.
TSB010421
TSB: Some 2018 ? 2024 model year Toyota vehicles equipped with an A25A-FKS, A25A-FXS, M20A-FKS, or M20A-FXS engine may exhibit one or more of the following conditions: ?Milky/discolored engine oil. ?An ?Oil Pressure Low? warning message on the Multi-information Display (MID). ?A MIL ON condition with Diagnostic Trouble Codes (DTCs) P05202A (Engine Oil Pressure Sensor/Switch ?A? Signal Stuck in Range) and/or P052477 (Engine Oil Pressure Too Low [Severe]) present. Moisture from blow-by gases condenses and accumulates in the engine oil during short trips in extreme cold weather. When the moisture in the oil freezes, the oil pressure may drop, and the aforementioned warning indicators may display. Follow the procedures in this bulletin to address these conditions.
T-SB-0083-23
TSB: Some 2021 ? 2022 model year Sienna Hybrid vehicles may exhibit a condition in which the fuel gauge reading changes when the vehicle is driven up or down an incline and left at an angle of up to 15° for five minutes or longer. The combination meter assembly ECU logic has been modified to reduce the possibility of this condition. Follow the Repair Procedure in this bulletin to reprogram the combination meter assembly ECU.
T-TT-0678-21 Rev
TT: Some 19CY LG DCM equipped vehicles may not be able to complete the firmware update due to not having an active account or waived services during the trial. Follow the steps below to enable ?Temp DCM Activation?.
TSB003220
TSB: Replacement certification labels (the vinyl label installed on the driver door or door post) and VIN plates (the metal plate riveted to dashboard) (see Figure 1) for most 1979 ? 2023 model year vehicles may be available provided the requests meet the criteria listed in this Service Bulletin. Follow the Procurement Procedure in this bulletin to request a replacement certification label or VIN plate.
TSB005123
OBSOLETE NOTICE August 17, 2023: This bulletin is no longer applicable and is now obsolete
TTT073723
TT: A very small percentage of customers experience operational difficulties with some telematics features which they cannot resolve on their own. These resources, in conjunction with the Repair Manual, are for dealership personnel to assist those customers with user issues, user errors, and compatibility issues with other vehicle systems and external applications encountered while operating telematics features. Toyota has developed and provided the following Telematics Diagnostic Guide to assist dealer technicians.
T-SB-0107-20
TSB: Flash reprogramming allows the Electronic Control Unit (ECU) software to be updated without replacing the ECU. Flash calibration updates for specific vehicle models/ECUs are released as field-fix procedures described in individual Service Bulletins. This bulletin details the Global Techstream+ (GTS+) ECU flash reprogramming procedures and outlines use of the Technical Information System (TIS) and the Calibration Update Wizard+ (CUW+). To ensure the correct ECU software is installed, ECUs will require a Security Signature before the ECU will initialize the flash reprogramming sequence. This bulletin also details the process for acquiring a Security Signature from TIS during the GTS+ ECU flash reprogramming process.
T-TT-0726-23
TT: Some 2021 - 2023 Highlander HV, RAV4 HV and Sienna HV vehicles equipped with Rear Motor Generator, MGR (Q610), may duplicate an abnormal noise (Drone, Growl, Humming, and/or other) from the MGR at various vehicle speeds and normal drive conditions. Please contact TAS for diagnostic instructions to aid in resolution of the condition.
TSB-0033-23
TSB: Some 2020 ? 2023 model year Highlander Hybrid and 2021 ? 2023 model year RAV4 Hybrid, RAV4 Prime, Sienna Hybrid, and Venza Hybrid vehicles may exhibit a MIL ON condition with one or both of the following Diagnostic Trouble Codes (DTCs) present: ?P24517F ? Evaporative Emission System Switching Valve Actuator Stuck Off. ?P14502A ? Fuel Tank Pressure Sensor Signal Stuck in Range.
T-SB-0018-23
TSB: Some 2021 ? 2023 model year Sienna Hybrid vehicles may exhibit a MIL ON condition with Diagnostic Trouble Code (DTC) P060694 (Hybrid/EV Powertrain Control Module Processor Unexpected Operation) present. The Hybrid Vehicle Control Computer logic has been modified to reduce the possibility of this condition.
T-TT-0699-22 Rev
TT: Some Model Year 2018-2023 vehicles equipped with A25A-FKS/FXS or M20A-FKS/FXS engines may display the following message ?Engine Maintenance Required Visit Your Dealer? on the combination meter
T-TT-0725-23
TT: Some 2021- 2023 Sienna HV vehicles may duplicate an abnormal noise (Growl, Humming and/or other) from the Hybrid T/A at various vehicle speeds and normal drive conditions. Please contact TAS for diagnostic instructions to aid in resolution of the condition.
T-TT-0723-23
TT: Some 2021 to 2023 MY vehicles equipped Rear Motor Generator, MGR (Q610) may experience an oil leak concern. This issue is currently under investigation
TT069722
TT: MIL ON with DTC(s) present for Hybrid/EV Battery Cooling Fan Circuit.
T-TT-0611-20 Rev
TT: To assist with the early detection and early resolution of audio related concerns, it may be requested as part of the remanufactured head unit return to recover MMR data from the head unit. The following steps are instructions on how to retrieve the data from the system and are only to be used when requested by audio suppliers, FTS, and/or FPEs.
T-SB-0106-22
TSB: Some 2018 ? 2022 model year Toyota vehicles equipped with a Premium Audio with Dynamic Navigation System, require a Special Service Tool (SST) USB flash drive to update the map, points of interest, and system software. The SST is used with applicable vehicles to deliver the update, however, the process for generating license keys differs from previous generations. Before attempting to perform a map update, the expiration date of the dynamic subscription (stored in the head unit), must be checked. If the expiration date has not passed, a license key may be generated without the purchase of an activation card number (ACN). Updating the map without the use of an ACN is considered an Embedded Navigation Update (refer to pg. 10) and performing this update does not extend the subscription to dynamic map services. If the subscription period has expired, or is expiring within the next 90 days, it should be recommended to the customer to purchase an ACN. Utilizing an ACN, will initiate the Dynamic Navigation Update (refer to pg. 4). This Dynamic Navigation Update will perform the embedded navigation update and provide dynamic map services for a period of two years from the date that the Dynamic Navigation Update is performed. ACNs are provided in a pamphlet available through the normal parts ordering system
T-SB-0094-21 Rev
TSB: Some 2005 ? 2022 model year Toyota vehicles that have undergone water intrusion may exhibit a condition in which a musty smell is present. Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this service bulletin is to provide general guidelines and procedures for odor remediation. This service bulletin provides a guide on how to prepare the interior of the vehicle prior to an odor remediation being performed, as well as contact information for an approved vendor who will arrange the remediation, and instructions on how to prepare the interior of the vehicle for reassembly once the remediation has been completed. Refer to all model and model year specific Repair Manuals and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines. This service bulletin is to provide a general overview and direction for the odor remediation process.
T-TT-0708-22
TT: Some Model Year 2018-2022 vehicles equipped with A25A-FKS or A25A-FXS engines may experience a MIL ON condition with the following DTCs: P043F00, P043E00, P24007E, P24007F, P24187E
T-TT-0703-22
TT: Vehicles listed above equipped with a Denso Ten radio (Entune Audio Plus or Premium Audio) may exhibit a condition in which the radio screen continues to show a Bluetooth phone call in progress after the call has ended. This condition has been confirmed with multiple Android phones, including Samsung Galaxy S21 and S22, and Google Pixel 6.
T-SB-0107-20 Rev
TSB: Flash reprogramming allows the Electronic Control Unit (ECU) software to be updated without replacing the ECU. Flash calibration updates for specific vehicle models/ECUs are released as field-fix procedures described in individual Service Bulletins. This bulletin details the Techstream ECU flash reprogramming process and outlines use of TIS and the Calibration Update Wizard (CUW). To ensure the correct ECU software is installed, ECUs will require a Security Signature before the ECU will initialize the flash reprogramming sequence. This bulletin also details the process for acquiring a Security Signature from TIS during the Techstream ECU flash reprogramming process
TSB004321Rev2
TSB: Some 2020 model year vehicles equipped with Audio Plus (version 1021) or Premium Audio (version 1021) or earlier may exhibit one or more of the following conditions: ?Barge in function defaulted to OFF. ?Limited phone book grammar. ?Difficult Hand Free operation. ?Abnormal Electronic Owner?s Manual operation. ?Music does not automatically resume when using Android Auto?. ?Cover art is not displayed. ?Vehicle position is not sent to Destination Assist server. ?System inoperative after using the return button when using voice recognition.
TSB011120Rev1
TSB: When certain vehicle ECUs are replaced, the ECU security key must be written in order for that ECU to communicate on the vehicle network. The Techstream Software Health Check Results screen has been enhanced to help identify if a replacement ECU requires an ECU security key.
TTT069922
TT: Some Model Year 2018-2021 vehicles equipped with A25A-FKS/FXS or M20A-FKS/FXS engines may display the following message ?Engine Maintenance Required Visit Your Dealer? on the combination meter.
22TD04 Remedy No
DP: A Toyota Genuine Accessory Dash Camera was installed in the involved vehicles. If the Micro SD Card used in the accessory dash camera is damaged the accessory dash camera may continuously attempt to read/write data to the card. This can lead to an increase in temperature of the card and may lead to localized melting of the card and the surrounding area of the dash cam.
22TD042
FAQ: LIMITED SERVICE CAMPAIGN 22TD04
FAQ 22TD04
FAQ: LIMITED SERVICE CAMPAIGN 22TD04
Instructions 22T
TI: TECHNICAL INSTRUCTIONS FOR LIMITED SERVICE CAMPAIGN 22TD04 ACCESSORY DASH CAMERA FIRMWARE UPDATE CERTAIN 2021 MODEL YEAR SIENNA VEHICLES CERTAIN 2021 MODEL YEAR VENZA VEHICLES
SERVICE CAMPAIGN
TI: TECHNICAL INSTRUCTIONS FOR LIMITED SERVICE CAMPAIGN 22TD04 ACCESSORY DASH CAMERA FIRMWARE UPDATE CERTAIN 2021 MODEL YEAR SIENNA VEHICLES CERTAIN 2021 MODEL YEAR VENZA VEHICLES
21TD02
RL: A Toyota Genuine Accessory Dash Camera was installed in the involved vehicles. If the Micro SD Card used in the accessory dash camera is damaged the accessory dash camera may continuously attempt to read/write data to the card. This can lead to an increase in temperature of the card and may lead to localized melting of the card and the surrounding area of the dash cam.
TSB001221Rev2
TSB: Some 2010 ? 2022 model year Toyota vehicles may exhibit paint stains after the removal of Rapgard?. The paint stains may appear to be under the clear coat but are usually under wrinkles in the Rapgard?. The wrinkles may trap water and cause the paint to stain from the trapped moisture, especially on horizontal surfaces such as the hood, roof, and trunk. Follow the Repair Procedure in this bulletin to address this condition
TSB008921Rev2
TSB: Some 2020 model year Camry, Camry Hybrid, Corolla Hatchback, RAV4, and RAV4 Hybrid vehicles may exhibit one or more of the following conditions: ?Diagnostic Trouble Code (DTC) B15A804 is present in current or history. ?Red SOS LED stays on after bulb check. ?Toyota App does not accept the activation code. ?Toyota App is inoperative. ?SOS call center does not receive the vehicle?s location in a timely manner. ?Toyota App shows an error 42 when trying to execute a command. ?Unable to remote start the vehicle with the key fob (if equipped). ?Unable to subscribe to remote services. ?Unable to activate Wi-Fi. ?Destination Assist is inoperative. Some 2020 ? 2021 model year Camry, Camry Hybrid, Corolla Hatchback, RAV4, and RAV4 Hybrid vehicles and some 2021 model year Avalon, Avalon Hybrid, Corolla, Corolla Hybrid, Sienna Hybrid, and Venza Hybrid vehicles may exhibit one or more of the following conditions: ?DTC B15A804 is present in current or history. ?Red SOS LED stays on after bulb check. ?Toyota App is inoperative. ?Unable to subscribe to remote services. ?Unable to activate Wi-Fi. ?Depleted 12V vehicle battery when in IG-OFF. ?Unable to reconnect out of network. A DCM reset and firmware update is now available to address these conditions. Follow the DCM Reset and Firmware Update Procedure in this bulletin to update the firmware.
TSB009421Rev1
TSB: Some 2005 ? 2022 model year Toyota vehicles that have undergone water intrusion may exhibit a condition in which a musty smell is present. Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this service bulletin is to provide general guidelines and procedures for odor remediation. This service bulletin provides a guide on how to prepare the interior of the vehicle prior to an odor remediation being performed, as well as contact information for an approved vendor who will arrange the remediation, and instructions on how to prepare the interior of the vehicle for reassembly once the remediation has been completed. Refer to all model and model year specific Repair Manuals and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines. This service bulletin is to provide a general overview and direction for the odor remediation process
TTT069522
TT: To improve customer support of telematics connected services features, additional resources have been provided in the Service Lane - Knowledge Center.
TSB008921Rev1
TSB: Some 2020 model year Camry, Camry Hybrid, Corolla Hatchback, RAV4, and RAV4 Hybrid vehicles may exhibit one or more of the following conditions: ?Diagnostic Trouble Code (DTC) B15A804 is present in current or history. ?Red SOS LED stays on after bulb check. ?Toyota App does not accept the activation code. ?Toyota App is inoperative. ?SOS call center does not receive the vehicle?s location in a timely manner. ?Toyota App shows an error 42 when trying to execute a command. ?Unable to remote start the vehicle with the key fob (if equipped). ?Unable to subscribe to remote services. ?Unable to activate Wi-Fi. ?Destination Assist is inoperative
TTT059920 Rev4
TT: Vehicle control apps might not operate as expected at times due to preconditions (normal operating parameters) not being established, vehicle settings and/or network/cellular coverage concerns
TSB002019
OBSOLETE NOTICE March 22, 2022: This bulletin is now obsolete. Please see T-SB-0024-22.
TSB002422
TSB: Some 2018 model year Camry and Camry Hybrid, 2019 model year Avalon and Avalon Hybrid, 2020 ? 2021 model year Highlander, Highlander Hybrid, and Corolla, and 2021 model year Sienna Hybrid vehicles may exhibit decreased front windshield defroster performance at extremely low ambient temperatures. This condition may be the result of the fresh/recirculation servo actuator separating from the servo. This condition does not affect the airflow of the defroster. Follow the Repair Procedure in this bulletin to address this condition.
T-TT-0687-22
TT: When customers have a concern about a discharged battery, no start, or general battery concern, the DCA-8000 is the only appropriate tool to use for diagnosis
T-TT-0599-20 Rev
TT: Vehicle control apps might not operate as expected at times due to preconditions (normal operating parameters) not being established, vehicle settings and/or network/cellular coverage concerns
T-SB-0012-21 Rev
TSB: Some 2010 ? 2022 model year Toyota vehicles may exhibit paint stains after the removal of Rapgard?. The paint stains may appear to be under the clear coat but are usually under wrinkles in the Rapgard?. The wrinkles may trap water and cause the paint to stain from the trapped moisture, especially on horizontal surfaces such as the hood, roof, and trunk. Follow the Repair Procedure in this bulletin to address this condition
T-TT-0678-21
TT: Some 19CY LG DCM equipped vehicles may not be able to complete the firmware update due to not having an active account or waived services during the trial. Follow the steps below to enable ?Temp DCM Activation?.
T-SB-0104-21
TSB: Some 2018 ? 2022 model year Toyota vehicles equipped with an A25A-FKS, A25A-FXS, or M20A-FKS engine may exhibit one or more of the following conditions: ?Milky/Discolored engine oil. ?An ?Oil Pressure Low? warning message on the Multi-information Display (MID). ?A MIL ON condition with Diagnostic Trouble Codes (DTCs) P05202A (Engine Oil Pressure Sensor/Switch "A" Signal Stuck in Range) and/or P052477 (Engine Oil Pressure too low [Severe]). Moisture from blow-by gases condenses and accumulates in the engine oil during short trips in extreme cold weather. When the moisture in the oil freezes, the oil pressure may drop, and the aforementioned warning indicators may display. Follow the procedures in this bulletin to address these conditions.
T-SB-0094-21
TSB: Some 2005 ? 2022 model year Toyota vehicles that have undergone water intrusion may exhibit a condition in which a musty smell is present. Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this service bulletin is to provide general guidelines and procedures for odor remediation. This service bulletin provides a guide on how to prepare the interior of the vehicle prior to an odor remediation being performed, as well as contact information for an approved vendor who will arrange the remediation, and instructions on how to prepare the interior of the vehicle for reassembly once the remediation has been completed. Refer to all model and model year specific Repair Manuals and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines. This service bulletin is to provide a general overview and direction for the odor remediation process.
T-SB-0019-21 Rev
TSB: Some 2020 model year vehicles equipped with Audio Plus (version 1186) or earlier may exhibit one or more of the following conditions: ?WiFi intermittently inoperative. ?DTC (Diagnostic Trouble Code) B15DB present. ?Changing the Auto Relock Timer setting also changes the Remote 2-Press unlock setting. Some 2020 ? 2021 model year vehicles equipped with Audio Plus (version 1210), or Premium Audio (version 1196) or earlier may exhibit one or more of the following conditions: ?Intermittent screen flashing. ?Intermittent ?Destination Assist Unavailable? pop-up message. ?Intermittent blank screen. ?Bluetooth® intermittently disconnects. ?Abnormal radio playback after Destination Assist Call. ??There is no playable data? pop-up message when using USB Audio. ?Unable to answer phone calls when using Apple CarPlay®. ?Clock displays the incorrect time. ?Intermittent rebooting. ??The software version doesn?t correspond? pop-up is intermittently displayed. ?Intermittent black screen when using projection navigation. ?Abnormal noise after ACC OFF/ON when using AM mode and high volume. ??Please connect USB? pop-up message when USB is already connected. Some 2020 ? 2021 model year vehicles equipped with Audio Plus (version 1256), or Premium Audio (version 1256) or earlier may exhibit one or more of the following conditions: ?Navigation intermittently reverses its travel. ?Android AutoTM inoperative. ?Audio mode is set to ?Off? after disconnecting USB while using Apple CarPlay®. ?Intermittent black screen flash when connecting Bluetooth®. ?When the MAP button is pressed, a ?Navi app is not installed? pop-up is displayed. ?Intermittent black map screen on home screen. ?Bluetooth® intermittently disconnects. ?No outgoing voice when using Bluetooth® Handsfree for phone call. ?Bluetooth® Now Playing List song selection is slow. ?Unable to transfer phone contacts when using Bluetooth®.
T-SB-0089-21
TSB: Some 2020 model year Camry, Camry Hybrid, Corolla Hatchback, RAV4, and RAV4 Hybrid vehicles may exhibit one or more of the following conditions: ?Diagnostic Trouble Code (DTC) B15A804 is present in current or history. ?Red SOS LED stays on after bulb check. ?Toyota App does not accept the activation code. ?Toyota App is inoperative. ?SOS call center does not receive the vehicle?s location in a timely manner. ?Toyota App shows an error 42 when trying to execute a command. ?Unable to remote start the vehicle with the key fob (if equipped). ?Unable to subscribe to remote services. ?Unable to activate Wi-Fi. ?Destination Assist is inoperative. Some 2020 ? 2021 model year Camry, Camry Hybrid, Corolla Hatchback, RAV4, and RAV4 Hybrid vehicles and some 2021 model year Avalon, Avalon Hybrid, Corolla, Corolla Hybrid, Sienna Hybrid, and Venza Hybrid vehicles may exhibit one or more of the following conditions: ?DTC B15A804 is present in current or history. ?Red SOS LED stays on after bulb check. ?Toyota App is inoperative. ?Unable to subscribe to remote services. ?Unable to activate Wi-Fi. ?Depleted 12V vehicle battery when in IG-OFF. ?Unable to reconnect out of network. A DCM reset and firmware update is now available to address these conditions. Follow the DCM Reset and Firmware Update Procedure in this bulletin to update the firmware.
T-SB-0095-20 Obs
OBSOLETE NOTICE October 14, 2021: This bulletin is now obsolete. Please see T-SB-0089-21.
T-TT-0663-21
TT: When used in conjunction with the Repair Manual, these Blind Spot Monitor, Forward Recognition Camera, and Front Millimeter Wave Radar tips leverage SSTs and readily available tools to support target placement in varying shop environments.
T-SB-0080-19 Rev
TSB: Some 2006 ? 2022 model year Toyota vehicles in particular geographic areas may exhibit a condition where the HVAC evaporator drain hose has become obstructed with an insect nest. An insect repellent drain hose tip (ARINIX® Tip) is available to help minimize future occurrences of this environmental condition. For some models, a new drain hose is required to properly fit the ARINIX® Tip. Follow the procedures in this bulletin for proper handling and installation of this optional service part.
T-SB-0050-21
TSB: Long-term or off-site storage requires special care to keep vehicles factory fresh and ready for delivery. The following guidelines should be performed to minimize vehicle component/part degradation due to extended vehicle storage conditions. Long-term storage can affect a vehicle?s systems and components. Any problems that are found should be corrected immediately.
T-TT-0653-21
TT: DTC P1AC000 is currently under investigation. Please create a TAS case and contact TAS for instruction prior to diagnosing or repairing the vehicle. For pre-sold units: Do not clear codes and contact TAS on the next available business day. For sold units: Continue with diagnosis and repair. Save all data and contact TAS on the next available business day. This is occurring in very low mileage vehicles at <500 miles.
Toyota PRO21-UFR
UPDATES TO THE 2014-2021 TOYOTA UNIVERSAL FLAT RATE MANUAL
T-SB-0031-21
TSB: Some 2021 model year Sienna Hybrid LE vehicles may exhibit a condition of inoperative remote functions from the app or key fob, such as remote engine start or door lock/unlock functions. Registering either, or both, the ?Remote Engine Starter Registration Status? and ?Remote Door Lock Function? may be necessary using Techstream to address this condition. Follow the Repair Procedure in this bulletin to address this condition.
T-PG007-01
Replacement vin plates.
T-PG002-91
Product general information.
Complaint counts are reports filed with NHTSA, not failure rates. A common model collects more of them than a rare one that breaks more often.