Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
T-SB-0035-24 Rev2
Service Bulletin/Repair Instructions
Acid rain results from rainwater or other airborne moisture that become acidic due to industrial chemical impurities in the atmosphere. If these acidic compounds settle on an exposed vehicle, especially the horizontal areas such as the hood, roof, and decklid, significant damage to the painted surfaces can occur. Acid rain damage can typically be identified on vehicles by the presence of stains on the paint surface that resemble hard water spots. Unlike water spots however, acid rain damage cannot be removed by regular washing procedures. Also, because acid rain can etch and soften the paint, normal buffing or polishing repair procedures should not be attempted. This can cause further damage and result in visible depressions in the paint surface. The following are the three major categories of acid rain damage: •Minor damage: requires only buffing to repair. •Moderate damage: usually requires neutralizing, color sanding, and buffing. •Severe damage: extending beyond 1/2 mil of clearcoat on a pearl, metallic, or solid color, requires neutralization, sanding, and repainting. In cases where acid rain damage is minor, neutralization and buffing with a liquid-type paint finessing product may provide an adequate repair. Only specially formulated products outlined in this bulletin should be used for that purpose. Unfortunately, other than minor damage, there is no simple method of determining the actual extent (depth) of acid penetration other than color sanding a representative affected area until there is no visible etching or depressions, followed by measuring the amount of paint removed with either a magnetic or digital-type film thickness gauge. The procedures in this bulletin are intended for use by qualified body/paint technicians and should not be attempted by inexperienced personnel. It is the dealer’s responsibility to protect and maintain the quality of the vehicle’s paint finish after receipt at the dealership prior to the first sale. Perform frequent vehicle washing, as often as daily, during high heat and humidity periods to minimize the potential for paint damage due to acid rain exposure. This is especially important in geographical areas known for high frequency and concentration of acid rain and industrial fallout.
T-SB-0038-24 Rev2
Service Bulletin/Repair Instructions
To prevent brake rotor rust from forming during transportation and storage, wheel film will be used instead of a cardboard type of anti-rust cover. The purpose of the wheel film is to shield the disc brake rotor from weather elements and initial rust before the vehicle is delivered to the customer. Consequently, the film should remain on the wheel for as long as possible.
T-SB-0039-24 Rev2
Service Bulletin/Repair Instructions
The condition known as acid rain is caused by airborne chemicals or particles in the atmosphere, which mix with rainwater, nighttime dew, or high humidity to form acidic compounds. If these contaminants settle and remain on a painted vehicle surface, especially the horizonal areas of the hood, roof, and decklid, significant damage can occur. This damage is the result of actual etching of the paint and appears as pitting or water spots. As acid rain droplets on the vehicle surface evaporate, the concentration strength of the acid increases, causing deeper and more rapid damage. This evaporation and corrosive action also occur more rapidly on dark colored cars as direct sun heat increases. It is the dealer’s responsibility to protect and maintain the quality of the vehicle’s paint finish after receipt at the dealership prior to the first sale. In areas known for high frequency and/or concentration of acid rain, frequent vehicle washing during high heat or humidity periods will minimize the potential for paint damage caused by acid rain. It is further recommended that either reverse osmosis or deionized water be used to prevent water spotting.
T-SB-0061-23 Rev2
Service Bulletin/Repair Instructions
Toyota vehicles are currently protected with RapgardTM protective film designed to protect the horizontal painted surfaces. This material protects from acid rain, environmental fallout, and rail contamination. Follow the Removal Procedure in this bulletin to remove the RapgardTM protective film within 90 days from initial application.
T-SB-0062-23 Rev2
Service Bulletin/Repair Instructions
Vehicles may occasionally be subjected to contamination by airborne iron particles shed from railroad tracks, train wheels, exposure to heavy machinery facilities, grinding, welding, etc. This type of contamination can be identified by the presence of small, red or brown particles on the paint surface. These particles are often difficult to see on dark color paints but can be easily felt when brushing a hand across horizontal body surfaces such as the hood, roof, or deck lid. Follow the Repair Procedure in this bulletin to clean vehicles that may have been subjected to contamination by airborne iron particles such as rail dust during rail transportation or extended storage near industrial areas.
T-SB-0035-24 Rev1
Service Bulletin/Repair Instructions
Acid rain results from rainwater or other airborne moisture that become acidic due to industrial chemical impurities in the atmosphere. If these acidic compounds settle on an exposed vehicle, especially the horizontal areas such as the hood, roof, and decklid, significant damage to the painted surfaces can occur. Acid rain damage can typically be identified on vehicles by the presence of stains on the paint surface that resemble hard water spots. Unlike water spots however, acid rain damage cannot be removed by regular washing procedures. Also, because acid rain can etch and soften the paint, normal buffing or polishing repair procedures should not be attempted. This can cause further damage and result in visible depressions in the paint surface. The following are the three major categories of acid rain damage: •Minor damage: requires only buffing to repair. •Moderate damage: usually requires neutralizing, color sanding, and buffing. •Severe damage: extending beyond 1/2 mil of clearcoat on a pearl, metallic, or solid color, requires neutralization, sanding, and repainting. In cases where acid rain damage is minor, neutralization and buffing with a liquid-type paint finessing product may provide an adequate repair. Only specially formulated products outlined in this bulletin should be used for that purpose. Unfortunately, other than minor damage, there is no simple method of determining the actual extent (depth) of acid penetration other than color sanding a representative affected area until there is no visible etching or depressions, followed by measuring the amount of paint removed with either a magnetic or digital-type film thickness gauge. The procedures in this bulletin are intended for use by qualified body/paint technicians and should not be attempted by inexperienced personnel. It is the dealer’s responsibility to protect and maintain the quality of the vehicle’s paint finish after receipt at the dealership prior to the first sale. Perform frequent vehicle washing, as often as daily, during high heat and humidity periods to minimize the potential for paint damage due to acid rain exposure. This is especially important in geographical areas known for high frequency and concentration of acid rain and industrial fallout.
T-SB-0038-24 Rev1
Service Bulletin/Repair Instructions
To prevent brake rotor rust from forming during transportation and storage, wheel film will be used instead of a cardboard type of anti-rust cover. The purpose of the wheel film is to shield the disc brake rotor from weather elements and initial rust before the vehicle is delivered to the customer. Consequently, the film should remain on the wheel for as long as possible.
T-SB-0039-24 Rev1
Service Bulletin/Repair Instructions
The condition known as acid rain is caused by airborne chemicals or particles in the atmosphere, which mix with rainwater, nighttime dew, or high humidity to form acidic compounds. If these contaminants settle and remain on a painted vehicle surface, especially the horizonal areas of the hood, roof, and decklid, significant damage can occur. This damage is the result of actual etching of the paint and appears as pitting or water spots. As acid rain droplets on the vehicle surface evaporate, the concentration strength of the acid increases, causing deeper and more rapid damage. This evaporation and corrosive action also occur more rapidly on dark colored cars as direct sun heat increases. It is the dealer’s responsibility to protect and maintain the quality of the vehicle’s paint finish after receipt at the dealership prior to the first sale. In areas known for high frequency and/or concentration of acid rain (see Figure 1), frequent vehicle washing during high heat or humidity periods will minimize the potential for paint damage caused by acid rain. It is further recommended that either reverse osmosis or deionized water be used to prevent water spotting.
T-SB-0061-23 Rev1
Service Bulletin/Repair Instructions
Toyota vehicles are currently protected with RapgardTM protective film designed to protect the horizontal painted surfaces. This material protects from acid rain, environmental fallout, and rail contamination.
T-SB-0062-23 Rev1
Service Bulletin/Repair Instructions
Vehicles may occasionally be subjected to contamination by airborne iron particles shed from railroad tracks, train wheels, exposure to heavy machinery facilities, grinding, welding, etc. This type of contamination can be identified by the presence of small, red or brown particles on the paint surface. These particles are often difficult to see on dark color paints but can be easily felt when brushing a hand across horizontal body surfaces such as the hood, roof, or deck lid.
T-SB-0035-24
Service Bulletin/Repair Instructions
Acid rain results from rainwater or other airborne moisture that become acidic due to industrial chemical impurities in the atmosphere. If these acidic compounds settle on an exposed vehicle, especially the horizontal areas such as the hood, roof, and decklid, significant damage to the painted surfaces can occur. Acid rain damage can typically be identified on vehicles by the presence of stains on the paint surface that resemble hard water spots. Unlike water spots however, acid rain damage cannot be removed by regular washing procedures. Also, because acid rain can etch and soften the paint, normal buffing or polishing repair procedures should not be attempted. This can cause further damage and result in visible depressions in the paint surface. The following are the three major categories of acid rain damage: •Minor damage: requires only buffing to repair. •Moderate damage: usually requires neutralizing, color sanding, and buffing. •Severe damage: extending beyond 1/2 mil of clearcoat on a pearl, metallic, or solid color, requires neutralization, sanding, and repainting. In cases where acid rain damage is minor, neutralization and buffing with a liquid-type paint finessing product may provide an adequate repair. Only specially formulated products outlined in this bulletin should be used for that purpose. Unfortunately, other than minor damage, there is no simple method of determining the actual extent (depth) of acid penetration other than color sanding a representative affected area until there is no visible etching or depressions, followed by measuring the amount of paint removed with either a magnetic or digital-type film thickness gauge. The procedures in this bulletin are intended for use by qualified body/paint technicians and should not be attempted by inexperienced personnel. While the quality and durability of paint on Toyota vehicles is continuously being improved, it remains the dealer’s responsibility to protect and maintain the quality of the vehicle’s paint finish after receipt at the dealership prior to the first sale. To read, While the quality and durability of paint on Toyota vehicles is continuously being improved, it remains the dealer’s responsibility to protect and maintain the quality of the vehicle’s paint finish after receipt at the dealership prior to first sale. Perform frequent vehicle washing, as often as daily, during high heat and humidity periods to minimize the potential for paint damage due to acid rain exposure. This is especially important in geographical areas known for high frequency and concentration of acid rain and industrial fallout.
T-SB-0038-24
Service Bulletin/Repair Instructions
To prevent brake rotor rust from forming during transportation and storage, wheel film will be used instead of a cardboard type of anti-rust cover. The purpose of the wheel film is to shield the disc brake rotor from weather elements and initial rust before the vehicle is delivered to the customer. Consequently, the film should remain on the wheel for as long as possible. SUPERSESSION NOTICE The information contained in this bulletin supersedes Service Bulletin No. PD017-04. •The entire bulletin has been updated.
T-SB-0039-24
Service Bulletin/Repair Instructions
The condition known as acid rain is caused by airborne chemicals or particles in the atmosphere, which mix with rainwater, nighttime dew, or high humidity to form acidic compounds. If these contaminants settle and remain on a painted vehicle surface, especially the horizonal areas of the hood, roof, and decklid, significant damage can occur. This damage is the result of actual etching of the paint and appears as pitting or water spots. As acid rain droplets on the vehicle surface evaporate, the concentration strength of the acid increases, causing deeper and more rapid damage. This evaporation and corrosive action also occur more rapidly on dark colored cars as direct sun heat increases. While Toyota paint quality, durability, and resistance to environmental factors is continuously being improved, it remains the responsibility of the dealer to protect and maintain the vehicle’s paint finish from the time of arrival at the dealership until retail delivery to the customer. In areas known for high frequency and/or concentration of acid rain (see Figure 1), frequent vehicle washing during high heat or humidity periods will minimize the potential for paint damage caused by acid rain. It is further recommended that either reverse osmosis or deionized water be used to prevent water spotting.
T-PANT-2024-004-
Service Bulletin/Repair Instructions
This is to advise of various price adjustments that will affect Toyota Genuine Motor Oil and Long Life Coolant, effective March 1, 2024. These products are ordered through the Toyota Complete Maintenance Care (TCMC) website.
T-SB-0043-14
Service Bulletin/Repair Instructions
OBSOLETE NOTICE January 22, 2024: This bulletin is now obsolete. Please see T-SB-0057-18.
TSB003220
Service Bulletin/Repair Instructions
TSB: Replacement certification labels (the vinyl label installed on the driver door or door post) and VIN plates (the metal plate riveted to dashboard) (see Figure 1) for most 1979 ? 2023 model year vehicles may be available provided the requests meet the criteria listed in this Service Bulletin. Follow the Procurement Procedure in this bulletin to request a replacement certification label or VIN plate.
T-SB-0057-18
Service Bulletin/Repair Instructions
TSB: The Immobilizer and Smart Key Reset is a feature that allows the registration of new keys when all master keys are lost. Once the system is reset, all previously registered keys will be erased. Follow the procedures in this bulletin to reset a vehicle Immobilizer or Smart Key system.
TTT063620
Service Bulletin/Repair Instructions
TT: Some Toyota vehicles installed with Toyota Complete Maintenance Care (TCMC) brake pads may exhibit a groan or squeak noise in various driving conditions
T-SB-0014-22
Service Bulletin/Repair Instructions
TSB: This Service Bulletin includes procedures to replace damaged or loose front carpet floor retainer(s) without replacing the carpet assembly. Follow the Repair Procedure in this bulletin to replace the loose or damaged carpet floor retainer(s).
Toyota Safety Re
Service Bulletin/Repair Instructions
Toyota Safety Recall and Service Campaign - Technician Certification Requirements
T-TT-0636-20 Rev
Service Bulletin/Repair Instructions
TT: Some Toyota vehicles installed with Toyota Complete Maintenance Care (TCMC) brake pads may exhibit a groan or squeak noise in various driving conditions.
ZE6-DLP 129-14-2
Service Bulletin/Repair Instructions
Warranty enhancement program.
T-SB-0032-20 Rev
Service Bulletin/Repair Instructions
TSB: Replacement certification labels (the vinyl label installed on the driver door or door post) and VIN plates (the metal plate riveted to dashboard) (see Figure 1) for most 1979 ? 2021 model year vehicles may be available provided the requests meet the criteria listed in this Service Bulletin. Follow the Procurement Procedure in this bulletin to request a replacement certification label or VIN plate.
T-TT-0636-20
Service Bulletin/Repair Instructions
TT: Some Toyota vehicles installed with Toyota Complete Maintenance Care (TCMC) brake pads may exhibit a groan or squeak noise in various driving conditions.
T-SB-0063-20
Service Bulletin/Repair Instructions
TSB: SUPERSESSION NOTICE The information contained in this bulletin supersedes Service Bulletin Nos. ST005-01, SU001-08, and T-SB-0391-08. The aforementioned bulletins are obsolete, and any printed versions should be discarded. Be sure to review the entire content of this service bulletin before proceeding. This Service Bulletin provides best practice procedures for vehicle pulling complaint, diagnosis, and repair for 2002 ? 2021 model year Toyota vehicles. This information supplements Repair Manual procedures when the symptoms are: ?Vehicle Pulling: The vehicle moves to the right or left when the driver holds the steering wheel while driving straight ahead without exerting steering effort. ?Steering Wheel Off Center: The vehicle travels straight, but the steering wheel is not pointed straight ahead. The vehicle is not pulling. Before repairing a vehicle pulling to one side, it is necessary to clearly identify the cause of the pulling condition. Frequently, pulling to one side is diagnosed as a wheel alignment concern. However, the actual cause may be related to the lateral force generated by the tires, vehicle damage, road crown or worn components. Performing a wheel alignment when tire force is the cause could result in the wheel alignment being set at a value outside of specifications. This could then cause other problems such as uneven tire wear, etc. A customer may notice a pull to the left when in the left lanes of travel and notice a pull to the right or no pull when traveling in the right lanes of travel on the very same section of roadway. This road crown effect is environmental and cannot be corrected with suspension adjustments or any other wheel or tire modification discussed in this bulletin.
T-SB-0391-08 Obs
Service Bulletin/Repair Instructions
TSB: OBSOLETE NOTICE June 23, 2020: This bulletin is now obsolete. Please see T-SB-0063-20.
T-SB-0304-17 Obs
Service Bulletin/Repair Instructions
TSB: OBSOLETE NOTICE April 07, 2020: This bulletin is now obsolete. Please see T-SB-0032-20. Replacement Certification Labels and VIN Plates
T-SB-0032-20
Service Bulletin/Repair Instructions
TSB: SUPERSESSION NOTICE The information contained in this bulletin supersedes Service Bulletin Nos. PG021-88, PG015-89, PG0015-90, PG002-91, PG002-93, PG005-97, PG007-01, PG007-07, PG006-01, PG004-97, T-SB-0144-08, and T-SB-0304-17. The aforementioned bulletins are obsolete, and any printed versions should be discarded. Replacement certification labels (the vinyl label installed on the driver door or door post) and VIN plates (the metal plate riveted to dashboard) (see Figure 1) for most 1979 ? 2020 model year vehicles may be available provided the requests meet the criteria listed in this Service Bulletin. Follow the Procurement Procedure in this bulletin to request a replacement certification label or VIN plate.
T-SB-0142-13_Obs
Service Bulletin/Repair Instructions
OBSOLETE NOTICE February 12, 2020: This bulletin is now obsolete. Please see T-SB-0010-20.
T-SB-0010-20
Service Bulletin/Repair Instructions
TSB: Some 2004 ? 2017 model year Toyota vehicles may exhibit odors naturally occurring from the HVAC system and/or related environmental factors. Although there is no way to eliminate these odors, follow the General Procedure in this bulletin to minimize the odors experienced
T-SB-0008-20
Service Bulletin/Repair Instructions
TSB: Vehicles may display evidence of a fluid leak or fluid seep from powertrain components. This bulletin explains how to determine the differences between a fluid leak versus a fluid seep. Cases that are determined to be a ?leak? should be repaired accordingly and will be covered under warranty if applicable. Cases that are determined to be a ?seep? should be documented on the repair order and inspected at the next service interval. Follow the Repair Information in this bulletin to determine if the concern in question is a fluid leak or fluid seep and review the Repair Procedure section to address the condition. NOTE This bulletin applies to ALL powertrain fluids excluding fuel and coolant.
T-SB-0134-16-Rev
Service Bulletin/Repair Instructions
TSB: REVISION NOTICE July 01, 2019 Rev2: ? Applicability has been updated to 2019 ? 2020 model year Toyota vehicles. ? The Techstream Preparation and Process Overview sections have been updated. October 30, 2017 Rev1: ? Applicability has been updated to include 2018 model year vehicles. Any previous printed versions of this bulletin should be discarded. SUPERSESSION NOTICE The information contained in this bulletin supersedes SB No. T-SB-0012-13. Service Bulletin No. T-SB-0012-13 is obsolete and any printed versions should be discarded. Be sure to review the entire content of this bulletin before proceeding. Flash reprogramming allows the Electronic Control Unit (ECU) software to be updated without replacing the ECU. Flash calibration updates for specific vehicle models/ECUs are released as field-fix procedures described in individual Service Bulletins. This bulletin details the Techstream ECU flash reprogramming process and outlines use of the Technical Information System (TIS) and the Calibration Update Wizard (CUW). Flash calibration updates can only be applied to the vehicle/ECU combination for which they are intended. ECUs have internal security that will not allow them to be programmed with another ECU?s information. NOTE ECU is a Toyota term used to describe integrated computerized devices responsible for managing the operation of a system or subsystem. For the purposes of this bulletin, the term ?ECU? is used as a generic label for the following SAE J1930 standard references: ? Powertrain Control Module (PCM) ? Engine Control Module (ECM) ? Transmission Control Module (TCM) ? Any other Toyota specific control unit
Expired Sienna R
Service Bulletin/Repair Instructions
Dealer Package: September 11, 2018 A watermark has been added to the Dealer Letter to indicate that ZTA expired on September 10, 2018. This notification UPDATES the previous version mailed in April, 2006. Changes to the previous version are noted in red. Please replace the previous version with this UPDATED version. Toyota will initiate a Customer Support Program (CSP) to provide supplemental tire warranty coverage for certain 2004 through early 2006 model year Sienna AWD and Mobility Assistance vehicles factory-equipped with run-flat tires.
PG004-97-Obsolet
Service Bulletin/Repair Instructions
Technical Service Bulletin: OBSOLETE NOTICE: July 31, 2018: This bulletin is now obsolete. Please see T-SB-0304-17.
PG006-01-Obsolet
Service Bulletin/Repair Instructions
Technical Service Bulletin: OBSOLETE NOTICE: July 31, 2018: This bulletin is now obsolete. Please see T-SB-0304-17.
T-SB-0304-17_Rev
Service Bulletin/Repair Instructions
TSB: REVISION NOTICE July 31, 2018 Rev2: ? The Supersession Notice has been updated. January 11, 2018 Rev1: ? The Supersession Notice has been updated. Any previous printed versions of this bulletin should be discarded. SUPERSESSION NOTICE The information contained in this bulletin supersedes Service Bulletin Nos. PG021-88, PG015-89, PG0015-90, PG002-91, PG002-93, PG005-97, PG007-01, PG007-07, PG006-01, PG004-97, and T-SB-0144-08. Service Bulletin Nos. PG021-88, PG015-89, PG0015-90, PG002-91, PG002-93, PG005-97, PG007-01, PG007-07, PG006-01, PG004-97, and T-SB-0144-08 are obsolete and any printed versions should be discarded. Vehicle replacement certification labels (the vinyl label installed on the driver door or door post) and VIN plates (the metal plate riveted to dashboard) may be available from Toyota, provided the request meets one of the criteria listed in this Service Bulletin. Replacement Certification Label and VIN Plate Criteria A replacement certification label and/or VIN plate may be requested if: ? The vehicle was in an accident and the label and/or plate is damaged or attached to a part that will be replaced during the repair. ? The label and/or plate was stolen.
ZF2_Expired Reme
Service Bulletin/Repair Instructions
Dealer Package: July 2, 2018 A watermark has been added to the Dealer Letter to indicate that ZF2 expired on June 30, 2018. Toyota has received a number of reports regarding front seatbelts in certain 2004 ? 2006 model year Sienna vehicles. In these reports, customers have indicated that the front seatbelts (right and/or left) may slowly or non-smoothly retract. Although the front seatbelt assembly is covered by Toyota?s New Vehicle Limited Warranty for 5 years or 60,000 miles (whichever comes first), we at Toyota care about the customers? ownership experience. Toyota is now extending the warranty coverage for repairs related to slow or non-smooth retraction of front seatbelts. The following information is provided to inform you and your staff of the program notification schedule and your degree of involvement. Owner Letter Mailing Date Toyota will begin to notify owners in mid-January, 2016 and will be mailed over several months. A sample of the owner notification letter has been included for your reference.
T-SB-0039-15_Rev
Service Bulletin/Repair Instructions
TSB: REVISION NOTICE May 25, 2018 Rev1: * The Introduction, Production Change Information, and Repair Procedure sections have been updated. Any previous printed versions of this bulletin should be discarded. Some 2003 - 2011 model year Toyota vehicles may exhibit a condition where the instrument panel pad (dashboard) becomes cracked and/or sticky. Follow the procedure in this bulletin to address this condition.
T-SB-0187-12_Rev
Service Bulletin/Repair Instructions
TSB: REVISION NOTICE February 12, 2018 Rev2: ? Applicability has been updated to include 2015 ? 2018 model year vehicles. January 23, 2014 Rev1: ? Applicability has been updated to include 2013 ? 2014 model year vehicles. Any previous printed versions of this bulletin should be discarded. Toyota vehicles are equipped with either conventional or run-flat tires. Sometimes punctures may occur as a result of contact with road debris or other hazards. If a puncture occurs, it may be possible to repair the tire and return it to service. With a conventional tire it is not possible to drive for an extended amount of time with the tire at low pressures as damage to the tire may occur. With run-flat tires, due to reinforced sidewalls, it is possible to drive for up to 100 miles at speeds less than 55 mph with little or no damage to the tire. The U.S. Tire Manufacturers Association (UTSMA) provides guidelines and recommendations for tire repair and replacement. It also provides information related to: ? Basic tire information ? Tire maintenance and safety ? Driver education, tire safety curriculum.
T-SB-0229-12_Rev
Service Bulletin/Repair Instructions
TSB: REVISION NOTICE November 22, 2017 Rev1: ? Applicability has been updated to include 2014 ? 2018 model year vehicles. Any previous printed versions of this bulletin should be discarded. In the event that a Toyota vehicle becomes submerged in water, many components may be physically damaged. Electrical and electronic components, including wiring harnesses, are particularly susceptible to corrosion and subsequent malfunction. Although any flooding can be damaging, salt water flooding elevates the potential for abnormal conditions and may increase risks due to its highly corrosive and conductive nature. Salt residue also continues to corrode and remain conductive even after a vehicle dries. This bulletin is intended to assist with safe handling and inspection of flood damaged vehicles and to provide basic guidance on likely needed repairs.
T-SB-0144-08_Obs
Service Bulletin/Repair Instructions
TSB: OBSOLETE NOTICE November 21, 2017: This bulletin is now obsolete. Please see T-SB-0304-17.
ZE6-Toyota POL14
Service Bulletin/Repair Instructions
Warranty Policy Bulletin: Toyota has received reports where some vehicles may exhibit cracked and/or sticky/melting dashboards as a result of heat or humidity. In Mid-December, 2014, Toyota announced the reimbursement Phase of this voluntary warranty enhancement program. Since prior to that announcement, Toyota has been diligently making parts preparations for the parts replacement phase of this Program. Due to the age, volume, and breadth of the covered vehicles subject to the Program and the size and complexity of dashboard manufacturing, Toyota has launched the part replacement portion of this Program in several phases.
T-SB-0134-16_Rev
Service Bulletin/Repair Instructions
TSB: REVISION NOTICE October 30, 2017 Rev1: * Applicability has been updated to include 2018 model year vehicles. SUPERSESSION NOTICE The information contained in this bulletin supersedes SB No. T-SB-0012-13. Flash reprogramming allows the Electronic Control Unit (ECU) software to be updated without replacing the ECU. Flash calibration updates for specific vehicle models/ECUs are released as field-fix procedures described in individual Service Bulletins. This bulletin details the Techstream ECU flash reprogramming process and outlines use of the Technical Information System (TIS) and the Calibration Update Wizard (CUW). Flash calibration updates can only be applied to the vehicle/ECU combination for which they are intended. ECUs have internal security that will not allow them to be programmed with another ECU's information.
T-SB-0304-17
Service Bulletin/Repair Instructions
TSB: Vehicle replacement certification labels (the vinyl label installed on the driver door or door post) and VIN plates (the metal plate riveted to dashboard) may be available from Toyota, provided the request meets one of the criteria listed in this Service Bulletin.
T-SB-0085-09_Rev
Service Bulletin/Repair Instructions
TSB: REVISION NOTICE October 25, 2017 Rev2: ? Applicability has been updated to include 2008 ? 2010 model year Sienna vehicles. ? The Production Change Information section has been removed. ? The Parts Information and Repair Procedure sections have been updated. SUPERSESSION NOTICE The information contained in this bulletin supersedes SB No. EL004-04. ? Applicability has been updated to include 2005 ? 2010 model year Sienna vehicles. Some 2004 ? 2010 model year Sienna vehicles may exhibit a condition where the power function of the sliding door is inoperative. A new service part has been developed so that the replacement of the entire motor/cable assembly is not required.
ESS_ Special Ser
Service Bulletin/Repair Instructions
Dealer Package: Toyota has received reports indicating that some vehicles experienced symptoms of the condition in Special Service Campaign A7E after being inspected and/or repaired.
ZE6_Toyota POL14
Service Bulletin/Repair Instructions
Warranty Policy Bulletin POL14-11: Rev Toyota has received reports where some vehicles may exhibit cracked and/or sticky/melting dashboards as a result of heat or humidity.
ZE6 Dealer Daily
Service Bulletin/Repair Instructions
Dealer Daily: Voluntary Extension of Warranty Coverage for Cracked and/or Sticky/Melting Dashboards (Instrument Panels) as a Result of Heat or Humidity.
ZE6_POL14-11_War
Service Bulletin/Repair Instructions
Warranty Policy Bulletin POL14-11: REVISED March 22, 2017: Toyota has received reports where some vehicles may exhibit cracked and/or sticky/melting dashboards as a result of heat or humidity.
HR1_Dealer Lette
Service Bulletin/Repair Instructions
Dealer Letter: Toyota will be sending Safety Recall Follow-Up Notices to remind owners whose vehicles have not yet had campaign repairs completed.
HR1_Region Lette
Service Bulletin/Repair Instructions
Region Letter: Toyota will be sending Safety Recall Follow-Up Notices to remind owners whose vehicles have not yet had campaign repairs completed.
TSB018217
Service Bulletin/Repair Instructions
TSB: SUPERSESSION NOTICE The information contained in this bulletin supersedes SB No. T-SB-0101-11. Applicability has been updated to include 2016 ? 2017 model year vehicles. Service Bulletin No. T-SB-0101-11 is Obsolete and any printed versions should be discarded. Be sure to review the entire content of this bulletin before proceeding. When servicing interior electrical switches and components, please note the precautions in this bulletin to avoid damaging electrical components and switches. Many lubricants, cleaners, and automotive chemicals contain silicone or other compounds that may contaminate electrical contacts, and therefore increase electrical resistance and decrease switch performance. The use of any cleaners or fluids may increase the risk of further damage to electrical components.
T-SB-0012-13 Rev
Service Bulletin/Repair Instructions
TSB: OBSOLETE NOTICE: September 14, 2016: This bulletin is now obsolete. Please see T-SB-0134-16.
T-SB-0142-13 Rev
Service Bulletin/Repair Instructions
TSB: REVISION NOTICE November 10, 2016 Rev2: ? Applicability has been updated to include 2016 ? 2017 model year Toyota vehicles. ? Parts Information section has been updated. Some 2004 ? 2017 model year Toyota vehicles may exhibit odors naturally occurring from the HVAC system and/or related environmental factors. Although there is no way to eliminate these odors, follow the General Procedure in this bulletin to minimize the odors experienced.
T-SB-0134-16
Service Bulletin/Repair Instructions
TSB: Supersession Notice. Flash reprogramming allows the ECU software to be updated without replacing the ECU. Flash calibration updates for specific vehicle models/ECUs are released as field-fix procedures described in individual Service Bulletins. This bulletin details the Techstream ECU flash reprogramming process and outlines use of the Technical Information System (TIS) and the Calibration Update Wizard (CUW). Flash calibration updates can only be applied to the vehicle/ECU combination for which they are intended. ECUs have internal security that will not allow them to be programmed with another ECU?s information.
Safety Recall an
Service Bulletin/Repair Instructions
Update on Technician Certification Requirements.
T-SB-0125-15 REV
Service Bulletin/Repair Instructions
TSB: WARRANTY OPERATION CODES UPDATED. SOME 2004 2006 MODEL YEAR SIENNA VEHICLES MAY EXHIBIT A CONDITION WHERE THE FRONT DRIVER AND/OR PASSENGER SEAT BELT BECOMES ABNORMALLY SLOW TO RETRACT, OR DOES NOT RETRACT SMOOTHLY. FOLLOW THE PROCEDURE IN THIS BULLETIN TO REPLACE THE FRONT SEAT BELT ASSEMBLIES TO ADDRESS THIS CONDITION.
T-SB-0125-15 Rev
Service Bulletin/Repair Instructions
TSB: Warranty Operation Codes updated. Some 2004 ? 2006 model year Sienna vehicles may exhibit a condition where the front driver and/or passenger seat belt becomes abnormally slow to retract, or does NOT retract smoothly. Follow the procedure in this bulletin to replace the front seat belt assemblies to address this condition.
ZE6_WEP_Dealer L
Service Bulletin/Repair Instructions
DL: In our continuing efforts to ensure the best in customer satisfaction, Toyota is announcing a Warranty Enhancement Program (the "Program"). This Program extends the warranty coverage for repairs related to cracked and/or sticky/melting Dashboards (Instrument Panels) as a result of heat or humidity on 2003 - 2005 model year 4Runner, 2005 - 2010 model year Avalon, 2007 - 2011 model year Camry and Camry Hybrid, 2004 -2010 model year Sienna, and 2004 - 2008 model year Solara vehicles. In Mid-December, 2014 Toyota announced the reimbursement Phase of this Program. Since prior to that announcement, Toyota has been diligently making parts preparations for the parts replacement phase of this Program. Due to the age, volume, and breadth of the covered vehicles subject to the Program and the size and complexity of dashboard manufacturing, Toyota will be launching the part replacement portion of this Program is several phases; please refer to the table below for part replacement model phasing.
ESS_Dealer Daily
Service Bulletin/Repair Instructions
Dealer Daily: Toyota has received reports indicating that some vehicles may experience spare tire carrier or carrier cable corrosion even after being inspected and/or repaired as part of a previous Special Service Campaign. During normal usage, water splashing rearward can reach the spare tire carrier due to variation in the placement of the foam splash guard or loss of the splash guard. If the splashed water contains high concentrations of road salt, corrosion of the spare tire carrier and the carrier cable may result. In limited instances, the spare tire may become seperated from the spare tire carrier and create a road hazard that could cause a vehicle crash. Toyota has revised the inspection and remedy procedures for this special service campaign. All owners of affected vehicles in Warm Climate States are now eligible for an inspection of the spare tire carrier assembly and cable.
ESS_Dealer Lette
Service Bulletin/Repair Instructions
Dealer Letter: Toyota has received reports indicating that some vehicles may experience spare tire carrier or carrier cable corrosion even after being inspected and/or repaired as part of a previous Special Service Campaign. During normal usage, water splashing rearward can reach the spare tire carrier due to variation in the placement of the foam splash guard or loss of the splash guard. If the splashed water contains high concentrations of road salt, corrosion of the spare tire carrier and the carrier cable may result. In limited instances, the spare tire may become seperated from the spare tire carrier and create a road hazard that could cause a vehicle crash. Toyota has revised the inspection and remedy procedures for this special service campaign. All owners of affected vehicles in Warm Climate States are now eligible for an inspection of the spare tire carrier assembly and cable.
ESS_Region Lette
Service Bulletin/Repair Instructions
Dealer Daily: The Special Service Campaign ESS Dealer Letter and Technical Instructions are now available on TIS.
ESS_Technical In
Service Bulletin/Repair Instructions
Technical Instructions: The repair quality of covered vehicles is extremely important to Toyota. All dealership technicians performing this repair are required to successfully complete the most current version of the E-Learning course ?Safety Recall and Service Campaign Essentials.? To ensure that all vehicles have the repair performed correctly, technicians performing this repair are required to currently hold at least one of the following certification levels: ? Toyota Certified (any classification) ? Toyota Expert (any classification) ? Master Technician ? Master Diagnostic Technician
GR1_DEALER LETTE
Service Bulletin/Repair Instructions
DEALER LETTER: SAFETY RECALL COMPLETION IS IMPORTANT NOT ONLY IN SATISFYING GOVERNMENT REQUIREMENTS, BUT ALSO IS AN INTEGRAL PART OF OUR COMMITMENT TO MEET CUSTOMER EXPECTATIONS OF TOYOTA PRODUCTS. TOYOTA WILL BE SENDING SAFETY RECALL FOLLOW-UP NOTICES TO REMIND OWNERS WHOSE VEHICLES HAVE NOT YET HAD CAMPAIGN REPAIRS COMPLETED. WE REQUEST YOUR ASSISTANCE IN COMPLETING THE APPLICABLE CAMPAIGN REPAIRS AS OWNERS RECEIVE THE FOLLOW-UP NOTICE AND CONTACT YOUR DEALERSHIP. PLEASE NOTE THE FOLLOW-UP ACTIVITY MAY CAUSE AN INCREASE IN YOUR CURRENT CAMPAIGN OWNER APPOINTMENTS. TOYOTA WILL CONTINUE WITH ADDITIONAL FOLLOW-UP ACTIVITIES IN THE MONTHS TO COME. PLEASE TAKE THIS INTO CONSIDERATION WHEN ANALYZING YOUR MANPOWER REQUIREMENTS.
GR1_Dealer Lette
Service Bulletin/Repair Instructions
Dealer Letter: Safety Recall completion is important not only in satisfying government requirements, but also is an integral part of our commitment to meet customer expectations of Toyota products. Toyota will be sending Safety Recall Follow-Up Notices to remind owners whose vehicles have not yet had campaign repairs completed. We request your assistance in completing the applicable campaign repairs as owners receive the Follow-Up Notice and contact your dealership. Please note the follow-up activity may cause an increase in your current campaign owner appointments. Toyota will continue with additional follow-up activities in the months to come. Please take this into consideration when analyzing your manpower requirements.
TC-16-001
Service Bulletin/Repair Instructions
Region Letter: Toyota will be sending Safety Recall Follow-Up Notices to remind owners whose vehicles have not yet had campaign repairs completed. Please note the following information for Regional and PD associates.
T-TT-0381-16
Service Bulletin/Repair Instructions
Tech Tip: Some customers may experience difficulty programming HomeLink.
Pol-16-01
Service Bulletin/Repair Instructions
In certain 2004 to 2006 model year Sienna vehicles, Toyota has received some reports where the front seatbelts (right and/or left) may slowly or non-smoothly retract.
ZF2_DEALER LETTE
Service Bulletin/Repair Instructions
DEALER LETTER: BACKGROUND TOYOTA HAS RECEIVED A NUMBER OF REPORTS REGARDING FRONT SEATBELTS IN CERTAIN 2004 2006 MODEL YEAR SIENNA VEHICLES. IN THESE REPORTS, CUSTOMERS HAVE INDICATED THAT THE FRONT SEATBELTS (RIGHT AND/OR LEFT) MAY SLOWLY OR NON-SMOOTHLY RETRACT. ALTHOUGH THE FRONT SEATBELT ASSEMBLY IS COVERED BY TOYOTAS NEW VEHICLE LIMITED WARRANTY FOR 5 YEARS OR 60,000 MILES (WHICHEVER COMES FIRST), WE AT TOYOTA CARE ABOUT THE CUSTOMERS OWNERSHIP EXPERIENCE. TOYOTA IS NOW EXTENDING THE WARRANTY COVERAGE FOR REPAIRS RELATED TO SLOW OR NON-SMOOTH RETRACTION OF FRONT SEATBELTS. THE FOLLOWING INFORMATION IS PROVIDED TO INFORM YOU AND YOUR STAFF OF THE PROGRAM NOTIFICATION SCHEDULE AND YOUR DEGREE OF INVOLVEMENT.
ZF2_Dealer Lette
Service Bulletin/Repair Instructions
Dealer Letter: Background Toyota has received a number of reports regarding front seatbelts in certain 2004 ? 2006 model year Sienna vehicles. In these reports, customers have indicated that the front seatbelts (right and/or left) may slowly or non-smoothly retract. Although the front seatbelt assembly is covered by Toyota?s New Vehicle Limited Warranty for 5 years or 60,000 miles (whichever comes first), we at Toyota care about the customers? ownership experience. Toyota is now extending the warranty coverage for repairs related to slow or non-smooth retraction of front seatbelts. The following information is provided to inform you and your staff of the program notification schedule and your degree of involvement.
ZF2_WARRANTY POL
Service Bulletin/Repair Instructions
IN CERTAIN 2004 TO 2006 MODEL YEAR SIENNA VEHICLES, TOYOTA HAS RECEIVED SOME REPORTS WHERE THE FRONT SEATBELTS (RIGHT AND/OR LEFT) MAY SLOWLY OR NON-SMOOTHLY RETRACT.
T-SB-0125-15
Service Bulletin/Repair Instructions
TSB: Some 2004 ? 2006 model year Sienna vehicles may exhibit a condition where the front driver and/or passenger seat belt becomes abnormally slow to retract, or does NOT retract smoothly. Follow the procedure in this bulletin to replace the front seat belt assemblies to address this condition.
POL14-11
Service Bulletin/Repair Instructions
WPB: TOYOTA HAS RECEIVED REPORTS WHERE SOME VEHICLES MAY EXHIBIT CRACKED AND/OR STICKY/MELTING DASHBOARDS AS A RESULT OF HEAT OR HUMIDITY. IN MID-DECEMBER, 2014, TOYOTA ANNOUNCED THE REIMBURSEMENT PHASE OF THIS WARRANTY ENHANCEMENT PROGRAM. SINCE PRIOR TO THAT ANNOUNCEMENT, TOYOTA HAS BEEN DILIGENTLY MAKING PARTS PREPARATIONS FOR THE PARTS REPLACEMENT PHASE OF THIS PROGRAM. DUE TO THE AGE, VOLUME, AND BREADTH OF THE COVERED VEHICLES SUBJECT TO THE PROGRAM AND THE SIZE AND COMPLEXITY OF DASHBOARD MANUFACTURING, TOYOTA HAS LAUNCHED THE PART REPLACEMENT PORTION OF THIS PROGRAM IN SEVERAL PHASES; PLEASE REFER TO THE TABLE BELOW FOR PART REPLACEMENT MODEL PHASING.
ZE6-Dealer Daily
Service Bulletin/Repair Instructions
DD: In Mid-December 2014, Toyota announced the reimbursement Phase of this Program. Since prior to that announcement, Toyota has been diligently making parts preparations for the parts replacement phase of this Program. Due to the age, volume, and breadth of the covered vehicles subject to the Program and the size and complexity of dashboard manufacturing, Toyota has launched the part replacement portion of this Program in several phases; please refer to the table below for part replacement model phasing.
ZE6-Dealer Lette
Service Bulletin/Repair Instructions
DL: In our continuing efforts to ensure the best in customer satisfaction, Toyota has announced a Warranty Enhancement Program (the ?Program?). This Program extends the warranty coverage for repairs related to cracked and/or sticky/melting Dashboards (Instrument Panels) as a result of heat or humidity on 2003-2005 model year 4Runner, 2005-2010 model year Avalon, 2007-2011 model year Camry and Camry Hybrid, 2004-2010 model year Sienna, and 2004-2008 model year Solara vehicles.
ZE6-WPB POL14-11
Service Bulletin/Repair Instructions
WPB: Toyota has received reports where some vehicles may exhibit cracked and/or sticky/melting dashboards as a result of heat or humidity. In Mid-December, 2014, Toyota announced the reimbursement Phase of this warranty enhancement program. Since prior to that announcement, Toyota has been diligently making parts preparations for the parts replacement phase of this Program. Due to the age, volume, and breadth of the covered vehicles subject to the Program and the size and complexity of dashboard manufacturing, Toyota has launched the part replacement portion of this Program in several phases; please refer to the table below for part replacement model phasing.
ZE6_DEALER 12/3
Service Bulletin/Repair Instructions
DL: IN OUR CONTINUING EFFORTS TO ENSURE THE BEST IN CUSTOMER SATISFACTION, TOYOTA HAS ANNOUNCED A WARRANTY ENHANCEMENT PROGRAM (THE PROGRAM). THIS PROGRAM EXTENDS THE WARRANTY COVERAGE FOR REPAIRS RELATED TO CRACKED AND/OR STICKY/MELTING DASHBOARDS (INSTRUMENT PANELS) AS A RESULT OF HEAT OR HUMIDITY ON 2003-2005 MODEL YEAR 4RUNNER, 2005-2010 MODEL YEAR AVALON, 2007-2011 MODEL YEAR CAMRY AND CAMRY HYBRID, 2004-2010 MODEL YEAR SIENNA, AND 2004-2008 MODEL YEAR SOLARA VEHICLES.
ZE6_DEALERD 12/3
Service Bulletin/Repair Instructions
DD: IN MID-DECEMBER 2014, TOYOTA ANNOUNCED THE REIMBURSEMENT PHASE OF THIS PROGRAM. SINCE PRIOR TO THAT ANNOUNCEMENT, TOYOTA HAS BEEN DILIGENTLY MAKING PARTS PREPARATIONS FOR THE PARTS REPLACEMENT PHASE OF THIS PROGRAM. DUE TO THE AGE, VOLUME, AND BREADTH OF THE COVERED VEHICLES SUBJECT TO THE PROGRAM AND THE SIZE AND COMPLEXITY OF DASHBOARD MANUFACTURING, TOYOTA HAS LAUNCHED THE PART REPLACEMENT PORTION OF THIS PROGRAM IN SEVERAL PHASES; PLEASE REFER TO THE TABLE BELOW FOR PART REPLACEMENT MODEL PHASING.
T-TT-0362-15
Service Bulletin/Repair Instructions
TT: The vehicle may be difficult to start or have an abnormally low or rough idle after the battery has been disconnected or power to the Engine ECM has been interrupted.
WPB (POL 14-11)_
Service Bulletin/Repair Instructions
WPB: Toyota has received reports where some vehicles may exhibit cracked and/or sticky/melting dashboards as a result of heat or humidity. In Mid-December, 2014 Toyota announced the reimbursement Phase of this warranty enhancement program. Since prior to that announcement, Toyota has been diligently making parts preparations for the parts replacement phase of this Program. Due to the age, volume, and breadth of the covered vehicles subject to the Program and the size and complexity of dashboard manufacturing, Toyota will be launching the part replacement portion of this Program in several phases; please refer to the table below for part replacement model phasing. Although Toyota is increasing production levels, it is difficult to predict customer demand and where parts need to be shipped to support customer demand. It is important that dealerships explain to customers that there still may be a period of time the customer will need to wait before part replacement can be performed. Please be sure to take this into consideration when performing customer scheduling.
T-TT-0086-11
Service Bulletin/Repair Instructions
TechTip: Condition - The vehicle may be difficult to start or have an abnormally low or rough idle after the battery has been disconnected or power to the Engine ECM has been interrupted.
ZE6_Dealer Lette
Service Bulletin/Repair Instructions
DL: In our continuing efforts to ensure the best in customer satisfaction, Toyota is announcing a Warranty Enhancement Program (the ?Program?). This Program extends the warranty coverage for repairs related to cracked and/or sticky/melting Dashboards (Instrument Panels) as a result of heat or humidity on 2003-2005 model year 4Runner, 2005-2010 model year Avalon, 2007-2011 model year Camry and Camry Hybrid, 2004-2010 model year Sienna, and 2004-2008 model year Solara vehicles.
ZE6_Warranty Enh
Service Bulletin/Repair Instructions
RL: In our continuing efforts to ensure the best in customer satisfaction, Toyota is announcing a Warranty Enhancement Program (the ?Program?). This Program extends the warranty coverage for repairs related to cracked and/or sticky/melting Dashboards (Instrument Panels) as a result of heat or humidity on 2003-2005 model year 4Runner, 2005-2010 model year Avalon, 2007-2011 model year Camry and Camry Hybrid, 2004-2010 model year Sienna, and 2004-2008 model year Solara vehicles.
T-SB-0043-14 Rev
Service Bulletin/Repair Instructions
TSB: The Immobilizer and Smart Key Reset is a feature that allows the registration of new keys when all master keys are lost. Once the system is reset, all previously registered keys will be erased. Follow the procedures in this bulletin to reset a vehicle Immobilizer or Smart Key system. NOTE: There are new security provisions required to obtain a Reset Pass-Code. It is critical that the instructions for this new process are reviewed BEFORE attempting to get a Pass-Code in the new system.
ZE6_WEP_Region L
Service Bulletin/Repair Instructions
RL: In our continuing efforts to ensure the best in customer satisfaction, Toyota is announcing a Warranty Enhancement Program (the "Program"). This Program extends the warranty coverage for repairs related to cracked and/or sticky/melting Dashboards (Instrument Panels) as a result of heat or humidity on 2003 - 2005 model year 4Runner, 2005 - 2010 model year Avalon, 2007 - 2011 model year Camry and Camry Hybrid, 2004 - 2010 model year Sienna, and 2004 - 2008 model year Solara vehicles.
ZE6_WPB POL14-11
Service Bulletin/Repair Instructions
WPB: Toyota has received reports where some vehicles may exhibit cracked and/or sticky/melting dashboards as a result of heat or humidity.
POL-14-11
Service Bulletin/Repair Instructions
TOYOTA: DURING THE HUMIDITY OR HEAT, THE DASHBOARD WOULD BE EITHER STICKY, MELTING, OR CRACKED AND A PART REPLACEMENT HAS PHASED INTO PROGRAM. MODELS 2003-05 4RUNNER, 2005-10 AVALON, 2007-11 CAMRY & HYBRID, 2004-10 SIENNA, 2004-08 SOLARA. *PE
T-SB-0039-15
Service Bulletin/Repair Instructions
TSB: Certain 2003 - 2011 model year Toyota vehicles may exhibit a condition where the instrument panel pad (dashboard) becomes cracked and/or has a shiny/degraded appearance. The pad surface may also become sticky or adherent. Follow the procedure in this bulletin to address this condition.
T-SB-0083-13 Rev
Service Bulletin/Repair Instructions
TSB: The procedure in this bulletin is a general guideline on how to properly diagnose the air conditioning system after a component failure. Refer to the applicable Repair Manual for vehicle specific repair procedures and parts.
T-SB-0101-11 Rev
Service Bulletin/Repair Instructions
TSB: When servicing interior electrical switches and components, please note the precautions in this bulletin to avoid damaging electrical components and switches. Many lubricants, cleaners, and automotive chemicals contain silicone or other compounds that may contaminate electrical contacts, and therefore increase electrical resistance and decrease switch performance. The use of any cleaners or fluids may increase the risk of further damage to electrical components.
GR1_REGION LETTE
Service Bulletin/Repair Instructions
REGION LETTER: TOYOTA WILL BE SENDING SAFETY RECALL FOLLOW-UP NOTICES TO REMIND OWNERS WHOSE VEHICLES HAVE NOT YET HAD CAMPAIGN REPAIRS COMPLETED. PLEASE NOTE THE FOLLOWING INFORMATION FOR REGIONAL AND PD ASSOCIATES.
T-SB-0012-13 REV
Service Bulletin/Repair Instructions
TSB: FLASH REPROGRAMMING ALLOWS THE ECU SOFTWARE TO BE UPDATED WITHOUT REPLACING THE ECU. FLASH CALIBRATION UPDATES FOR SPECIFIC VEHICLE MODELS/ECUS ARE RELEASED AS FIELD-FIX PROCEDURES DESCRIBED IN INDIVIDUAL SERVICE BULLETINS. THIS BULLETIN DETAILS THE TECHSTREAM ECU FLASH REPROGRAMMING PROCESS AND OUTLINES USE OF THE TECHNICAL INFORMATION SYSTEM (TIS) AND THE CALIBRATION UPDATE WIZARD (CUW). FLASH CALIBRATION UPDATES CAN ONLY BE APPLIED TO THE VEHICLE/ECU COMBINATION FOR WHICH THEY ARE INTENDED. ECUS HAVE INTERNAL SECURITY THAT WILL NOT ALLOW THEM TO BE PROGRAMMED WITH ANOTHER ECUS INFORMATION.
TSB-0012-13 Rev2
Service Bulletin/Repair Instructions
TSB: Flash reprogramming allows the ECU software to be updated without replacing the ECU. Flash calibration updates for specific vehicle models/ECUs are released as field-fix procedures described in individual Service Bulletins. This bulletin details the Techstream ECU flash reprogramming process and outlines use of the Technical Information System (TIS) and the Calibration Update Wizard (CUW). Flash calibration updates can only be applied to the vehicle/ECU combination for which they are intended. ECUs have internal security that will not allow them to be programmed with another ECU?s information.
ZE6-DLP 129-14
Service Bulletin/Repair Instructions
Warranty enhancement program.
ZE6_Electronic C
Service Bulletin/Repair Instructions
Electronic Communication: In our continuing efforts to ensure the best in customer satisfaction, Toyota is announcing a Warranty Enhancement Program. This program extends the warranty coverage for repairs related to cracked and/or sticky/melted dashboards (Instrument Panels) as a result of heat or humidity on 2003-2005 model year 4Runner, 2005-2010 model year Avalon, 2007-2011 model year Camry and Camry Hybrid, 2004-2010 model year Sienna, and 2004-2008 model year Solara vehicles.
ZE6_Region Lette
Service Bulletin/Repair Instructions
Region Letter: In our continuing efforts to ensure the best in customer satisfaction, Toyota is announcing a Warranty Enhancement Program. This program extends the warranty coverage for repairs related to cracked and/or sticky/melted dashboards (Instrument Panels) as a result of heat or humidity on 2003-2005 model year 4Runner, 2005-2010 model year Avalon, 2007-2011 model year Camry and Camry Hybrid, 2004-2010 model year Sienna, and 2004-2008 model year Solara vehicles.
ER11_Re-Notifica
Service Bulletin/Repair Instructions
Region Letter: Safety Recall completion is important not only in satisfying government requirements but also is an integral part of our commitment to meet customer expectations of Toyota products. Toyota will be sending Safety Recall Follow-Up Notices to remind owners whose vehicles have not yet had campaign repairs completed. We request your assistance in completing the applicable campaign repairs as owners receive the Follow-Up Notice and contact your dealership. Please note the follow-up activity may cause an increase in your current campaign owner appointments. Toyota will continue with additional follow-up activities in the months to come. Please take this into consideration when analyzing your manpower requirements.
T-SB-0014-11 Rev
Service Bulletin/Repair Instructions
TSB: The purpose of this service bulletin is to provide information regarding the installation of the correct torque converter bolts during automatic transmission/transaxle assembly replacement. Incorrect torque converter bolts or missing washers can cause damage to the torque converter assembly.
T-SB-0134-14
Service Bulletin/Repair Instructions
TSB: The purpose of this bulletin is to provide precautions to follow when installing an automatic transmission/transaxle assembly to avoid MIL "ON" shifting issues and/or transmission damage. Use the information in this bulletin when installing an automatic transmission/transaxle assembly.
T-TT-0010-10 Rev
Service Bulletin/Repair Instructions
Tech Tip: Low battery voltage can contribute to a MIL "ON" condition for P0335 (Crankshaft Position Sensor Circuit) and/or P0340 (Camshaft Position Sensor Circuit) due to inconsistent rotational speed of the engine's crankshaft.
T-SB-0030-14
Service Bulletin/Repair Instructions
A new repair procedure and overhaul kit have been developed for repairing the power steering rack to improve the overall serviceability and reduce ownership cost. This repair procedure only applies to vehicles where the steering rack leak is originating from the right (passenger) side and is the OEM steering rack assembly.
T-SB-0097-12 OBS
Service Bulletin/Repair Instructions
This bulletin is now obsolete. Please see T-SB-0030-14 .
ER4 Dealer Lette
Service Bulletin/Repair Instructions
Safety Recall completion is important not only in satisfying government requirements but also is an integral part of our commitment to meet customer expectations of Toyota products. Toyota will be sending Safety Recall Follow-Up Notices to remind owners whose vehicles have not yet had campaign repairs completed. We request your assistance in completing the applicable campaign repairs as owners receive the Follow-Up Notice and contact your dealership. Please note the follow-up activity may cause an increase in your current campaign owner appointments. Toyota will continue with additional follow-up activities in the months to come. Please take this into consideration when analyzing your manpower requirements.
ER4 Region Lette
Service Bulletin/Repair Instructions
Toyota will be sending Safety Recall Follow-Up Notices to remind owners whose vehicles have not yet had campaign repairs completed. Please note the following information for Regional and PD associates.
T-TT-0132-11
Service Bulletin/Repair Instructions
A key part to maintain the proper function and safe operation of the vehicle's braking system is to perform a visual inspection when installing brake pads, calipers, and discs. The following recommendations are intended to provide general tips for the inspection and/or installation of Toyota Complete Maintenance Care (TCMC) front brake pads and discs. Always refer to the model specific Repair manual and TIS publications for specific repair instructions.
T-SB-0187-12 Rev
Service Bulletin/Repair Instructions
Toyota vehicles are equipped with either conventional or run-flat tires. Sometimes punctures may occur as a result of contact with road debris or other hazards. If a puncture occurs, it may be possible to repair the tire and return it to service. With a conventional tire it is not possible to drive for an extended amount of time with the tire at low pressures as damage to the tire may occur. With run-flat tires, due to reinforced sidewalls, it is possible to drive for up to 100 miles (160 km) at speeds less than 55 mph (90 km/h) with little or no damage to the tire.
Warranty Enhance
Service Bulletin/Repair Instructions
Toyota has received reports regarding excessive electrical resistance in the Side Airbag connector of certain 2004 to 2009 Model Year Sienna vehicles. The connector could have been improperly crimped during the manufacturing process. In certain cases, oxidization buildup in the connector can occur resulting in illumination of the airbag warning lamp.
TC-14-001
Service Bulletin/Repair Instructions
TOYOTA: SEE DOCUMENT SEARCH BUTTON FOR OWNER LETTER. THERE IS AN EXCESSIVE ELECTRICAL RESISTANCE, ON SOME VEHICLES, WHERE THE CONNECTOR HAD BEEN IMPROPERLY CRIMPED, DURING TIME OF MANUFACTURING, AND OXIDIZATION BUILDUP, IN CONNECTOR, RESULT IN AN ILLUMINATION OF AIRBAG WARNING LAMP. SEE TSB-0069-12 REV 2. MODEL 2004-2009 SIENNA. *PE
T-SB-0069-12 Rev
Service Bulletin/Repair Instructions
Some 2004 ? 2009 model year Sienna vehicles may exhibit an SRS lamp ?ON? condition with Diagnostic Trouble Code (DTC) B0111 and/or B0116. An updated repair procedure is available to address this condition. Follow the procedures in this bulletin to repair the floor harness and the side airbag squib circuit.
T-TT-0213-13
Service Bulletin/Repair Instructions
Toyota vehicles are equipped with Supplemental Restraint Systems (SRS), including various airbags and in some models, seat belt pre-tensioners, to help reduce the risk of injury in a collision. If a customer expresses any concerns that the SRS airbags or pre-tensioner devices did not perform as expected (including an unintended deployment event), please follow the steps in the recommendations section below.
T-SB-0185-13
Service Bulletin/Repair Instructions
The following procedures are recommended during routine maintenance or in the event of a customer concern for wiper performance.
TS-BO030-01 Obso
Service Bulletin/Repair Instructions
This bulletin is now obsolete. Please see T-SB-0185-13.
T-SB-0122-11 Rev
Service Bulletin/Repair Instructions
Beginning in 1998, Toyota introduced side airbags as optional equipment. Toyota does NOT recommend replacement of original seat covers with non-Toyota leather or other seat cover materials on vehicles due to the following: Seat covers NOT recommended by Toyota may affect side airbag performance, in general or in part, during an accident. Modifications that negatively affect side airbag performance can result in severe occupant injuries. Seat covers are an integral part of this safety system. Replacing fabric seat covers with non-Toyota leather or other seat cover materials may compromise the effectiveness of this safety system. The design of the seat is complex, integrating safety and strength with comfort and luxury. Toyota strongly discourages modifying original equipment seats that have optional side airbags. Additionally, Toyota strongly advises against the installation or use of aftermarket seat covers, which could impair the performance of the side airbags in the event of an accident.
T-TT-0269-13
Service Bulletin/Repair Instructions
The appearance of spots in tempered glass (when viewed at certain angles) is the result of the heat treating and quick quenching process during manufacturing.
DR8 Reg Ltr
Service Bulletin/Repair Instructions
Toyota will be sending Safety Recall Follow-Up Notices to remind owners whose vehicles have not yet had campaign repairs completed. Please note the following information for Regional and PD associates.
T-SB-0071-11 Rev
Service Bulletin/Repair Instructions
The purpose of this service bulletin is to provide precautions to follow when installing an automatic transmission/transaxle assembly to avoid MIL ?ON,? shifting issues, and/or transmission damage. Use the information in this bulletin when installing an automatic transmission/transaxle assembly
T-TT-0051-10
Service Bulletin/Repair Instructions
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
T-TT-0051-10 Rev
Service Bulletin/Repair Instructions
If a customer states there is an unpleasant odor in the vehicle from the HVAC system, there are various factors that may be involved.
T-SB-0142-13
Service Bulletin/Repair Instructions
Some 2004 ? 2014 model year Toyota vehicles may exhibit odors naturally occurring from the HVAC system and/or related environmental factors. Although there is no way to eliminate these odors, follow the General Procedure in this bulletin to minimize the odors experienced.
T-SB-0141-13
Service Bulletin/Repair Instructions
A new Special Service Tool (SST 09709-00002) has been introduced to aid in the inspection procedure for certain vehicles equipped with a floor pedal-type parking brake system. This bulletin references the correct method for installing the Brake Pedal Force Gauge. Refer to the appropriate Repair Manual for parking brake pedal travel inspection and adjustment specification.
TC13-019
Service Bulletin/Repair Instructions
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
T-TT-0092-11 Rev
Service Bulletin/Repair Instructions
Some customers may complain that the Rear Seat Entertainment (RSE) system is inoperative if the have misplaced the parental passcode for the system.
T-PG006-00 Obsol
Service Bulletin/Repair Instructions
This bulletin is now obsolete. Please see T-SB-0054-13.
T-SB-0054-13
Service Bulletin/Repair Instructions
California (CA), Federal (FED), and 50 State Certified emission control underhood labels (emission labels) may be obtained through your dealership?s Parts Department utilizing standard replacement parts ordering procedures. Follow the guidelines outlined in this bulletin to ensure proper label application.
T-SB-0141-10 Rev
Service Bulletin/Repair Instructions
If a creak, tick, or rattle noise is heard at the top or bottom of the windshield, or at the top of the rear glass, the source of the noise may be the two stoppers bonded to the top of the windshield/rear glass, or the windshield retainers bonded to the lower edge of the windshield. This bulletin provides the recommended repair procedure to eliminate these types of noises from the windshield/rear glass area.
T-TT-0226-13
Service Bulletin/Repair Instructions
The customer is having difficulty changing the multi-display screen from Day Mode. If the multi-display screen is set to Day Mode when the headlights are on, the setting we be memorized when the engine is turned off.
Recall Follow Up
Service Bulletin/Repair Instructions
Toyota will be sending Safety Recall Follow-up notices to remind owners whose vehicles have not yet had campaign repairs completed
TC13-005
Service Bulletin/Repair Instructions
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
T-SB-0391-08 Rev
Service Bulletin/Repair Instructions
This bulletin contains general vehicle pulling diagnosis and repair procedures along with specific information to help correct pulling complaints.
SST Requirements
Service Bulletin/Repair Instructions
SSTs are key elements to provide your customers with swift and accurate repairs resulting in superior customer satisfaction.
T-SB-0012-13
Service Bulletin/Repair Instructions
Flash reprogramming allows the ECU software to be updated without replacing the ECU. Flash calibration updates for specific vehicle models/ECUs are released as field-fix procedures described in individual Service Bulletins. This bulletin details the Techstream ECU flash reprogramming process and outlines use of the TIS and the CUW.
T-SB-0064-10 Rev
Service Bulletin/Repair Instructions
This bulletin is now obsolete. Please see T-SB-0012-13.
T-SB-0187-12
Service Bulletin/Repair Instructions
Toyota vehicles are equipped with either conventional or run-flat tires. Sometimes punctures may occur as a result of contact with road debris or other hazards. If a puncture occurs, it may be possible to repair the tire and return it to service. With a conventional tire it is not possible to drive for an extended amount of time with the tire at low pressures as damage to the tire may occur. With run-flat tires, due to reinforced sidewalls, it is possible to drive for up to 100 miles (160 km) at speeds less than 55 mph (90 km/h) with little or no damage to the tire.
T-SB-0097-12
Service Bulletin/Repair Instructions
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
TSB-0097-12
Service Bulletin/Repair Instructions
TOYOTA: INFORMATION BEING PROVIDED REGARDING REPAIR PROCEDURE TO CORRECT OIL LEAKAGE FROM BOOTS OF STEERING GEAR ASSEMBLY. *PE
TSB-0087-12
Service Bulletin/Repair Instructions
TOYOTA: ACCELERATOR PEDAL SENSOR ASSEMBLY INFORMATION REGARDING THE INSPECTION, REMOVAL, AND INSTALLATION, IF LUBRICATION OR OIL, IS APPLIED. *PE
TSB-0122-11
Service Bulletin/Repair Instructions
TOYOTA: INFORMATION PROVIDED FOR REPLACING THE SEAT COVERS FOR VEHICLES EQUIPPED WITH SIDE AIRBAGS. *PE
TSB-0061-11
Service Bulletin/Repair Instructions
TOYOTA: 2004-2009 SIENNA. THE POWER REAR HATCH WILL NOT CLOSE COMPLETELY. THE HATCH WILL START TO CLOSE AND THEN WILL REVERSE BACK UP TO THE OPEN POSITION. *RM
TC-11-003
Service Bulletin/Repair Instructions
TOYOTA SERVICE CAMPAIGN: SEE DOCUMENT SEARCH BUTTON FOR OWNER LETTER. IN COLD WEATHER WHERE SALT IS USED, THE SALT CAN CORRODE THE SPARE TIRE CARRIER CABLE. 1998-2020 SIENNA. *RM
SB-0280-10
Service Bulletin/Repair Instructions
TOYOTA: SOME VEHICLES MAY EXHIBIT A CONDITION WHERE ONE OR BOTH SLIDING DOORS DO NOT OPEN OR CLOSE SMOOTHLY. INSPECT THE SLIDING DOOR LOCK ASSEMBLIES AND REPLACE THE AFFECTED COMPONENTS AS NEEDED, ACCORDING TO THE LISTED INSTRUCTIONS. *PE
TSB-0064-10
Service Bulletin/Repair Instructions
TOYOTA: TECHSTREAM ECU FLASH REPROGRAMMING PROCEDURE. FLASH REPROGRAMMING ALLOWS THE ECU SOFTWARE TO BE UPDATED WITHOUT REPLACING THE ECU. FLASH CALIBRATION UPDATES FOR SPECIFIC VEHICLE MODELS/ECUS ARE RELEASED AS FIELD-FIX PROCEDURES DESCRIBED IN INDIVIDUAL SERVICE BULLETINS. MODEL YEARS FROM 2001-2011. *PE
TSB-0085-09
Service Bulletin/Repair Instructions
TOYOTA: VEHICLES MAY EXPERIENCE A CONDITION WHERE THE POWER FUNCTION OF THE SLIDING DOOR IS INOPERATIVE. *PE
T-SB-0381-08
Service Bulletin/Repair Instructions
TOYOTA: SPARE TIRE CARRIER BINDING. SOME CUSTOMERS MAY EXPERIENCE THAT THE SPARE TIRE IS DIFFICULT TO REMOVE OR THE CABLE IS BINDING. *JS
0077-08
Service Bulletin/Repair Instructions
MOBILITY CONVERTED VEHICLE SERVICE INFORMATION. *PE
EL001-08
Service Bulletin/Repair Instructions
REPAIR MANUAL SUPPLEMENT: SRS LIGHT [ON] - DTC B0111/B0116 - OPEN SIDE SQUIB CIRCUIT. *NJ UPDATED 5/1/08. *NJ
0801
Service Bulletin/Repair Instructions
CUSTOMER SUPPORT PROGRAM - WARRANTY COVERAGE ENHANCEMENT FOR CERTAIN 2004 THROUGH 2006 MODEL YEAR SIENNA MODELS BACK DOOR STAY (REAR LIFTGATE STRUT). *NJ
08001
Service Bulletin/Repair Instructions
CUSTOMER SUPPORT PROGRAM - WARRANTY COVERAGE EXTENSION FOR THE BACK DOOR STAYS (REAR LIFTGATE STRUTS) ON CERTAIN 2004 THROUGH 2006 MY SIENNA VEHICLES. *NJ
01107
Service Bulletin/Repair Instructions
POWER BACK DOOR & POWER SLIDING DOOR DIFFICULT CLOSE. *NJ
07017
Service Bulletin/Repair Instructions
CUSTOMER SUPPORT PROGRAM - WARRANTY COVERAGE EXTENSION FOR THE FRONT DOOR CHECK ON CERTAIN 2004-2007 MY SIENNA VEHICLES. *NJ
07015
Service Bulletin/Repair Instructions
CUSTOMER SUPPORT PROGRAM - WARRANTY COVERAGE EXTENSION ON CERTAIN 2004 - EARLY 2005 MY 4RUNNER, LAND CRUISER AND SIENNA VEHICLES EQUIPPED WITH THE OPTIONAL REAR (BACK-UP) CAMERA. *NJ
05506
Service Bulletin/Repair Instructions
ENGINE PINGING OR KNOCKING NOISE. *KB
00307
Service Bulletin/Repair Instructions
DOOR CHECK POPPING NOISE. *KB
00107
Service Bulletin/Repair Instructions
STEERING INTERMEDIATE SHAFT IN HIGH ROAD SALT AREAS. *KB
00304
Service Bulletin/Repair Instructions
BACK DOOR STAY LEAK AND COLD WEATHER SHUDDER IMPROVEMENT. *TT
0601
Service Bulletin/Repair Instructions
REPORTS REGARDING UNEVEN OR PREMATURE TIRE WEAR ON SOME FACTORY-EQUIPPED DUNLOP SP SPORT 4000 DSST P225/60R17 AND BRIDGESTONE B380 RFT P225/60R17 RUN-FLAT TIRES. CUSTOMER SUPPORT PROGRAM - WARRANTY COVERAGE ENHANCEMENT FOR ALL WHEEL DRIVE (AWD) VEHICLES EQUIPPED WITH RUN-FLAT TIRES. *TT
04305
Service Bulletin/Repair Instructions
NO START IN SUB-FREEZING AMBIENT AIR TEMPERATURES. *TT
0506
Service Bulletin/Repair Instructions
WARRANTY COVERAGE ENHANCEMENT - ISOLATED REPORTS FROM EXTREME COLD CLIMATE AREAS THAT THE RADIATOR MAY CRACK AT THE BASE OF ONE OR MORE OF THE RADIATOR TUBES, RESULTING IN COOLANT LEAKAGE - CUSTOMER SUPPORT PROGRAM. *TT
00404
Service Bulletin/Repair Instructions
SLIDING DOOR RATTLE. *TT
00206
Service Bulletin/Repair Instructions
SEAT HEATER INOPERATIVE. *TT
00405
Service Bulletin/Repair Instructions
FRONT SUSPENSION TICK NOISE. *TT
01205
Service Bulletin/Repair Instructions
REPAIR MANUAL SUPPLEMENT: LASER CRUISE CONTROL BEAM AXIS ADJUSTMENT. *AK
00605
Service Bulletin/Repair Instructions
SQUEAL OR CHIRP TYPE NOISE EMITTED FROM THE BLOWER MOTOR AT VARIOUS SPEEDS. *TT
01105
Service Bulletin/Repair Instructions
COUNTERMEASURES TO THE AIR CONDITIONER (A/C) MAGNETIC CLUTCH RELAY FOR A/C LIGHT FLASHING (INOPERATIVE A/C) ISSUES ON SOME VEHICLES EQUIPPED WITH A MAGNETIC CLUTCH COMPRESSOR. *TT
00805
Service Bulletin/Repair Instructions
REAR WIPER IMPROVEMENT. *TT
01005
Service Bulletin/Repair Instructions
DIAGNOSTIC GUIDE FOR REAR SEAT ENTERTAINMENT SYSTEMS. *TT
01605
Service Bulletin/Repair Instructions
FUEL INJECTOR TICKING NOISE. *TT *SC
00105
Service Bulletin/Repair Instructions
MALFUNCTION INDICATOR LAMP (MIL) ON WITH DIAGNOSTIC TROUBLE CODE (DTC) P0031, P0051, P2238, AND/OR P2241. *TT
00205
Service Bulletin/Repair Instructions
MALFUNCTION INDICATOR LAMP (MIL) ON WITH DIAGNOSTIC TROUBLE CODE (DTC) P0346 (CAMSHAFT POSITION SENSOR A CIRCUIT RANGE/PERFORMANCE [BANK 2]). *TT
01004
Service Bulletin/Repair Instructions
TRANSMISSION SHIFTER MAY BECOME PROGRESSIVELY DIFFICULT TO MOVE. *TT
00804
Service Bulletin/Repair Instructions
INTERMITTENT VSC ACTIVATION AFTER STARTING THE ENGINE AND DRIVING STRAIGHT FROM A STOP POSITION. THIS CONDITION IS ALWAYS ACCOMPANIED BY THE INSTRUMENT PANEL VSC LIGHT AND AUDIBLE WARNING BUZZER TURNING ON AT THE SAME TIME. *NM UPDATE. *TT
04804
Service Bulletin/Repair Instructions
REPAIR MANUAL SUPPLEMENT: LEV II EVAP SYSTEM CHECK - DIAGNOSTIC TROUBLE CODE (DTC) P0441, P0442, P0446, P0451, P0452, P0453, P0455 AND P0456. *NM
04017
Service Bulletin/Repair Instructions
LIMITED SERVICE CAMPAIGN (LSC) 40I TO REPLACE THE RADIATOR. COLD WEATHER CONDITIONS MAY CAUSE THE BASE OF THE RADIATOR WALL TO CRACK, RESULTING IN THE LEAKAGE OF ENGINE COOLANT. *TT THIS IS AN AMENDED VERSION. *TT
TC04016
Service Bulletin/Repair Instructions
LIMITED SERVICE CAMPAIGN 40H TO REPLACE THE POWER STEERING FLUID RETURN HOSES. TECHNICAL INSTRUCTIONS; DEALERSHIP AND OWNER NOTIFICATION. *TT
00504
Service Bulletin/Repair Instructions
TIRE PRESSURE WARNING SYSTEM INFORMATION AND RE-INITIALIZATION. *TT
04104
Service Bulletin/Repair Instructions
MALFUNCTION INDICATOR LAMP (MIL) ON, DIAGNOSTIC TROUBLE CODE (DTC) P0037, P0038 OR P0136. *NM
03704
Service Bulletin/Repair Instructions
ENGINE BANK 1 AND BANK 2 A/F AND 02 IDENTIFICATION. VARIOUS TOYOTA MODELS. *TT
00904
Service Bulletin/Repair Instructions
POWER WINDOW / ROOF INITIALIZATION PROCEDURES. *TT
02904
Service Bulletin/Repair Instructions
MALFUNCTION INDICATOR LAMP ON WITH DIAGNOSTIC TROUBLE CODE P0171 AND/OR P0174 ENGINE RUNNING LEAN. *TT
0301
Service Bulletin/Repair Instructions
THERE MAY BE A RED POWER WIRE FOR POWER LUMBAR SUPPORT THAT IS NOT TIED SECURELY AWAY FROM PARKING BRAKE MECHANISM. *TT
01604
Service Bulletin/Repair Instructions
REAR NO. 2 SEAT STORAGE POSITION. *TT
00604
Service Bulletin/Repair Instructions
PERSONAL LIGHT OPERATION. *TT
04005
Service Bulletin/Repair Instructions
OWNER RENOTIFICATION OF NON-COMPLETED SPECIAL SERVICE CAMPAIGNS AND LIMITED SERVICE CAMPAIGNS. VARIOUS MODLES INCLUDING THE TOYOTA SCION XB MY2004. *TT
00204
Service Bulletin/Repair Instructions
THE PROPER IDENTIFICATION OF THE 7 SOLENOIDS USED IN THE U151E/U151F TRANSMISSIONS. *TT
00104
Service Bulletin/Repair Instructions
MALFUNCTION INDICATOR LAMP (MIL) ON DIAGNOSTIC TROUBLE CODE (DTC) P0748, P0798, P0985 OR P0986. *TT
00203
Service Bulletin/Repair Instructions
OXYGEN SENSOR (O2S) MONITOR THRESHOLD VALUES FOR ALL TOYOTA MODELS FROM 1996 TO 2003 AND VARIOUS 2004 MODELS INCLUDING COROLLA, ECHO AND SCION XA & XB MODELS. *TT
02003
Service Bulletin/Repair Instructions
MALFUNCTION INDICATOR LAMP (MIL) ON CONDITION WITH DIAGNOSTIC TROUBLE CODE (DTC) P0441, P0442 AND/OR P0446. *TT
00403
Service Bulletin/Repair Instructions
DIAGNOSTIC TROUBLE CODE (DTC) C1234 - YAW RATE SENSOR. *TT
00703
Service Bulletin/Repair Instructions
ENGINE CONTROL MODULE (ECM) CALIBRATION - SHIFTING ENHANCEMENT. *TT UPDATE. *TT
00703R
Service Bulletin/Repair Instructions
ENGINE CONTROL MODULE (ECM) CALIBRATION - SHIFTING ENHANCEMENT. REVISED. *TT
SSC30K
Service Bulletin/Repair Instructions
FUEL TANK REPLACEMENT - URGENT TO DEALERS. *TT
PG00503
Service Bulletin/Repair Instructions
SPARE TIRE CARRIER OPERATION. VARIOUS MODLELS INCLUDING THE 2004 LANDCRUISER AND 4 RUNNER. *TT
TC03018
Service Bulletin/Repair Instructions
FUEL TANK REPLACEMENT. SPECIAL SERVICE CAMPAIGN 30K. *TT
00503
Service Bulletin/Repair Instructions
2004 MODEL YEAR PRE-DELIVERY SERVICE (PDS). ALL '04 MODELS EXCEPT PRIUS. *TT
NV00903
Service Bulletin/Repair Instructions
FRONT DOOR WIND NOISE. REVISED. *TT
EL01103
Service Bulletin/Repair Instructions
POWER SLIDING DOOR DRIVE CABLE ROUTING. *TT
TC00203
Service Bulletin/Repair Instructions
WHENEVER AN AUTOMATIC TRANSMISSION IS REPLACED, OVERHAULED OR INDIVIDUAL COMPONENTS ARE REPLACED, USE THIS PROCEDURE TO CLEAR ENGINE CONTROL MODULE (ECM) LEARNED VALUES TO PREVENT SUBSEQUENT DRIVEABILITY COMPLAINTS. REVISED NOTICE. TUNDRA VEHICLES ADDED. *TT
00302
Service Bulletin/Repair Instructions
DIAGNOSTIC TESTER IMMOBILIZER FUNCTIONS - REVISED. *TT
T-PG007-01
Service Bulletin/Repair Instructions
Replacement vin plates.
T-PG002-91
Service Bulletin/Repair Instructions
Product general information.
01011901
Service Bulletin/Repair Instructions
CLASS ACTION LAWSUIT SETTLEMENT NOTICE. RUN FLAT TIRES MAY HAVE UNEVEN WEAR. *KB