Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
T-SB-0055-24 Rev2
Service Bulletin/Repair Instructions
Some 2005 – 2026 Toyota vehicles that have undergone water intrusion may exhibit a condition in which a musty odor is present. Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this Service Bulletin is to provide general guidelines and procedures for odor remediation. This Service Bulletin provides a guide on how to prepare and treat the interior of the vehicle for odor remediation. Refer to the applicable model and model year Repair Manual and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines.
T-SB-0035-24 Rev2
Service Bulletin/Repair Instructions
Acid rain results from rainwater or other airborne moisture that become acidic due to industrial chemical impurities in the atmosphere. If these acidic compounds settle on an exposed vehicle, especially the horizontal areas such as the hood, roof, and decklid, significant damage to the painted surfaces can occur. Acid rain damage can typically be identified on vehicles by the presence of stains on the paint surface that resemble hard water spots. Unlike water spots however, acid rain damage cannot be removed by regular washing procedures. Also, because acid rain can etch and soften the paint, normal buffing or polishing repair procedures should not be attempted. This can cause further damage and result in visible depressions in the paint surface. The following are the three major categories of acid rain damage: •Minor damage: requires only buffing to repair. •Moderate damage: usually requires neutralizing, color sanding, and buffing. •Severe damage: extending beyond 1/2 mil of clearcoat on a pearl, metallic, or solid color, requires neutralization, sanding, and repainting. In cases where acid rain damage is minor, neutralization and buffing with a liquid-type paint finessing product may provide an adequate repair. Only specially formulated products outlined in this bulletin should be used for that purpose. Unfortunately, other than minor damage, there is no simple method of determining the actual extent (depth) of acid penetration other than color sanding a representative affected area until there is no visible etching or depressions, followed by measuring the amount of paint removed with either a magnetic or digital-type film thickness gauge. The procedures in this bulletin are intended for use by qualified body/paint technicians and should not be attempted by inexperienced personnel. It is the dealer’s responsibility to protect and maintain the quality of the vehicle’s paint finish after receipt at the dealership prior to the first sale. Perform frequent vehicle washing, as often as daily, during high heat and humidity periods to minimize the potential for paint damage due to acid rain exposure. This is especially important in geographical areas known for high frequency and concentration of acid rain and industrial fallout.
T-SB-0038-24 Rev2
Service Bulletin/Repair Instructions
To prevent brake rotor rust from forming during transportation and storage, wheel film will be used instead of a cardboard type of anti-rust cover. The purpose of the wheel film is to shield the disc brake rotor from weather elements and initial rust before the vehicle is delivered to the customer. Consequently, the film should remain on the wheel for as long as possible.
T-SB-0039-24 Rev2
Service Bulletin/Repair Instructions
The condition known as acid rain is caused by airborne chemicals or particles in the atmosphere, which mix with rainwater, nighttime dew, or high humidity to form acidic compounds. If these contaminants settle and remain on a painted vehicle surface, especially the horizonal areas of the hood, roof, and decklid, significant damage can occur. This damage is the result of actual etching of the paint and appears as pitting or water spots. As acid rain droplets on the vehicle surface evaporate, the concentration strength of the acid increases, causing deeper and more rapid damage. This evaporation and corrosive action also occur more rapidly on dark colored cars as direct sun heat increases. It is the dealer’s responsibility to protect and maintain the quality of the vehicle’s paint finish after receipt at the dealership prior to the first sale. In areas known for high frequency and/or concentration of acid rain, frequent vehicle washing during high heat or humidity periods will minimize the potential for paint damage caused by acid rain. It is further recommended that either reverse osmosis or deionized water be used to prevent water spotting.
T-SB-0061-23 Rev2
Service Bulletin/Repair Instructions
Toyota vehicles are currently protected with RapgardTM protective film designed to protect the horizontal painted surfaces. This material protects from acid rain, environmental fallout, and rail contamination. Follow the Removal Procedure in this bulletin to remove the RapgardTM protective film within 90 days from initial application.
T-SB-0062-23 Rev2
Service Bulletin/Repair Instructions
Vehicles may occasionally be subjected to contamination by airborne iron particles shed from railroad tracks, train wheels, exposure to heavy machinery facilities, grinding, welding, etc. This type of contamination can be identified by the presence of small, red or brown particles on the paint surface. These particles are often difficult to see on dark color paints but can be easily felt when brushing a hand across horizontal body surfaces such as the hood, roof, or deck lid. Follow the Repair Procedure in this bulletin to clean vehicles that may have been subjected to contamination by airborne iron particles such as rail dust during rail transportation or extended storage near industrial areas.
T-SB-0055-24 Rev1
Service Bulletin/Repair Instructions
Some 2005 – 2024 Toyota vehicles that have undergone water intrusion may exhibit a condition in which a musty odor is present. Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this Service Bulletin is to provide general guidelines and procedures for odor remediation. This Service Bulletin provides a guide on how to prepare and treat the interior of the vehicle for odor remediation. Refer to the applicable model and model year Repair Manual and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines. This Service Bulletin is to provide a general overview and direction for the odor remediation process.
T-SB-0035-24 Rev1
Service Bulletin/Repair Instructions
Acid rain results from rainwater or other airborne moisture that become acidic due to industrial chemical impurities in the atmosphere. If these acidic compounds settle on an exposed vehicle, especially the horizontal areas such as the hood, roof, and decklid, significant damage to the painted surfaces can occur. Acid rain damage can typically be identified on vehicles by the presence of stains on the paint surface that resemble hard water spots. Unlike water spots however, acid rain damage cannot be removed by regular washing procedures. Also, because acid rain can etch and soften the paint, normal buffing or polishing repair procedures should not be attempted. This can cause further damage and result in visible depressions in the paint surface. The following are the three major categories of acid rain damage: •Minor damage: requires only buffing to repair. •Moderate damage: usually requires neutralizing, color sanding, and buffing. •Severe damage: extending beyond 1/2 mil of clearcoat on a pearl, metallic, or solid color, requires neutralization, sanding, and repainting. In cases where acid rain damage is minor, neutralization and buffing with a liquid-type paint finessing product may provide an adequate repair. Only specially formulated products outlined in this bulletin should be used for that purpose. Unfortunately, other than minor damage, there is no simple method of determining the actual extent (depth) of acid penetration other than color sanding a representative affected area until there is no visible etching or depressions, followed by measuring the amount of paint removed with either a magnetic or digital-type film thickness gauge. The procedures in this bulletin are intended for use by qualified body/paint technicians and should not be attempted by inexperienced personnel. It is the dealer’s responsibility to protect and maintain the quality of the vehicle’s paint finish after receipt at the dealership prior to the first sale. Perform frequent vehicle washing, as often as daily, during high heat and humidity periods to minimize the potential for paint damage due to acid rain exposure. This is especially important in geographical areas known for high frequency and concentration of acid rain and industrial fallout.
T-SB-0038-24 Rev1
Service Bulletin/Repair Instructions
To prevent brake rotor rust from forming during transportation and storage, wheel film will be used instead of a cardboard type of anti-rust cover. The purpose of the wheel film is to shield the disc brake rotor from weather elements and initial rust before the vehicle is delivered to the customer. Consequently, the film should remain on the wheel for as long as possible.
T-SB-0039-24 Rev1
Service Bulletin/Repair Instructions
The condition known as acid rain is caused by airborne chemicals or particles in the atmosphere, which mix with rainwater, nighttime dew, or high humidity to form acidic compounds. If these contaminants settle and remain on a painted vehicle surface, especially the horizonal areas of the hood, roof, and decklid, significant damage can occur. This damage is the result of actual etching of the paint and appears as pitting or water spots. As acid rain droplets on the vehicle surface evaporate, the concentration strength of the acid increases, causing deeper and more rapid damage. This evaporation and corrosive action also occur more rapidly on dark colored cars as direct sun heat increases. It is the dealer’s responsibility to protect and maintain the quality of the vehicle’s paint finish after receipt at the dealership prior to the first sale. In areas known for high frequency and/or concentration of acid rain (see Figure 1), frequent vehicle washing during high heat or humidity periods will minimize the potential for paint damage caused by acid rain. It is further recommended that either reverse osmosis or deionized water be used to prevent water spotting.
T-SB-0055-24
Service Bulletin/Repair Instructions
Some 2005 – 2024 Toyota vehicles that have undergone water intrusion may exhibit a condition in which a musty odor is present. Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this Service Bulletin is to provide general guidelines and procedures for odor remediation. This Service Bulletin provides a guide on how to prepare and treat the interior of the vehicle for odor remediation. Refer to the applicable model and model year Repair Manual and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines.
T-SB-0103-20 Rev1
Service Bulletin/Repair Instructions
This Service Bulletin provides updated non-electric water pump leak inspection and diagnostic tips for some 2008 – 2025 model year Toyota vehicles.
T-SB-0061-23 Rev1
Service Bulletin/Repair Instructions
Toyota vehicles are currently protected with RapgardTM protective film designed to protect the horizontal painted surfaces. This material protects from acid rain, environmental fallout, and rail contamination.
T-SB-0062-23 Rev1
Service Bulletin/Repair Instructions
Vehicles may occasionally be subjected to contamination by airborne iron particles shed from railroad tracks, train wheels, exposure to heavy machinery facilities, grinding, welding, etc. This type of contamination can be identified by the presence of small, red or brown particles on the paint surface. These particles are often difficult to see on dark color paints but can be easily felt when brushing a hand across horizontal body surfaces such as the hood, roof, or deck lid.
T-SB-0035-24
Service Bulletin/Repair Instructions
Acid rain results from rainwater or other airborne moisture that become acidic due to industrial chemical impurities in the atmosphere. If these acidic compounds settle on an exposed vehicle, especially the horizontal areas such as the hood, roof, and decklid, significant damage to the painted surfaces can occur. Acid rain damage can typically be identified on vehicles by the presence of stains on the paint surface that resemble hard water spots. Unlike water spots however, acid rain damage cannot be removed by regular washing procedures. Also, because acid rain can etch and soften the paint, normal buffing or polishing repair procedures should not be attempted. This can cause further damage and result in visible depressions in the paint surface. The following are the three major categories of acid rain damage: •Minor damage: requires only buffing to repair. •Moderate damage: usually requires neutralizing, color sanding, and buffing. •Severe damage: extending beyond 1/2 mil of clearcoat on a pearl, metallic, or solid color, requires neutralization, sanding, and repainting. In cases where acid rain damage is minor, neutralization and buffing with a liquid-type paint finessing product may provide an adequate repair. Only specially formulated products outlined in this bulletin should be used for that purpose. Unfortunately, other than minor damage, there is no simple method of determining the actual extent (depth) of acid penetration other than color sanding a representative affected area until there is no visible etching or depressions, followed by measuring the amount of paint removed with either a magnetic or digital-type film thickness gauge. The procedures in this bulletin are intended for use by qualified body/paint technicians and should not be attempted by inexperienced personnel. While the quality and durability of paint on Toyota vehicles is continuously being improved, it remains the dealer’s responsibility to protect and maintain the quality of the vehicle’s paint finish after receipt at the dealership prior to the first sale. To read, While the quality and durability of paint on Toyota vehicles is continuously being improved, it remains the dealer’s responsibility to protect and maintain the quality of the vehicle’s paint finish after receipt at the dealership prior to first sale. Perform frequent vehicle washing, as often as daily, during high heat and humidity periods to minimize the potential for paint damage due to acid rain exposure. This is especially important in geographical areas known for high frequency and concentration of acid rain and industrial fallout.
T-SB-0038-24
Service Bulletin/Repair Instructions
To prevent brake rotor rust from forming during transportation and storage, wheel film will be used instead of a cardboard type of anti-rust cover. The purpose of the wheel film is to shield the disc brake rotor from weather elements and initial rust before the vehicle is delivered to the customer. Consequently, the film should remain on the wheel for as long as possible. SUPERSESSION NOTICE The information contained in this bulletin supersedes Service Bulletin No. PD017-04. •The entire bulletin has been updated.
T-SB-0039-24
Service Bulletin/Repair Instructions
The condition known as acid rain is caused by airborne chemicals or particles in the atmosphere, which mix with rainwater, nighttime dew, or high humidity to form acidic compounds. If these contaminants settle and remain on a painted vehicle surface, especially the horizonal areas of the hood, roof, and decklid, significant damage can occur. This damage is the result of actual etching of the paint and appears as pitting or water spots. As acid rain droplets on the vehicle surface evaporate, the concentration strength of the acid increases, causing deeper and more rapid damage. This evaporation and corrosive action also occur more rapidly on dark colored cars as direct sun heat increases. While Toyota paint quality, durability, and resistance to environmental factors is continuously being improved, it remains the responsibility of the dealer to protect and maintain the vehicle’s paint finish from the time of arrival at the dealership until retail delivery to the customer. In areas known for high frequency and/or concentration of acid rain (see Figure 1), frequent vehicle washing during high heat or humidity periods will minimize the potential for paint damage caused by acid rain. It is further recommended that either reverse osmosis or deionized water be used to prevent water spotting.
T-PANT-2024-004-
Service Bulletin/Repair Instructions
This is to advise of various price adjustments that will affect Toyota Genuine Motor Oil and Long Life Coolant, effective March 1, 2024. These products are ordered through the Toyota Complete Maintenance Care (TCMC) website.
T-SB-0043-14
Service Bulletin/Repair Instructions
OBSOLETE NOTICE January 22, 2024: This bulletin is now obsolete. Please see T-SB-0057-18.
TSB003220
Service Bulletin/Repair Instructions
TSB: Replacement certification labels (the vinyl label installed on the driver door or door post) and VIN plates (the metal plate riveted to dashboard) (see Figure 1) for most 1979 ? 2023 model year vehicles may be available provided the requests meet the criteria listed in this Service Bulletin. Follow the Procurement Procedure in this bulletin to request a replacement certification label or VIN plate.
T-SB-0057-18
Service Bulletin/Repair Instructions
TSB: The Immobilizer and Smart Key Reset is a feature that allows the registration of new keys when all master keys are lost. Once the system is reset, all previously registered keys will be erased. Follow the procedures in this bulletin to reset a vehicle Immobilizer or Smart Key system.
T-SB-0094-21 Rev
Service Bulletin/Repair Instructions
TSB: Some 2005 ? 2022 model year Toyota vehicles that have undergone water intrusion may exhibit a condition in which a musty smell is present. Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this service bulletin is to provide general guidelines and procedures for odor remediation. This service bulletin provides a guide on how to prepare the interior of the vehicle prior to an odor remediation being performed, as well as contact information for an approved vendor who will arrange the remediation, and instructions on how to prepare the interior of the vehicle for reassembly once the remediation has been completed. Refer to all model and model year specific Repair Manuals and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines. This service bulletin is to provide a general overview and direction for the odor remediation process.
22TE04 - Takata
Service Bulletin/Repair Instructions
CSP: On July 30, 2018, a settlement of claims for Economic Loss related to Takata airbag inflators was approved for full implementation. The settlement includes Toyota?s agreement to provide a Customer Support Program (?CSP?) for 2002-2019 model year (MY) vehicles originally equipped with certain Takata airbag inflators or repaired under a recall with Takata airbag inflators to provide coverage for repairs of the airbag inflator contained in the airbag module. This CSP letter is to help clarify how to administer this coverage in accordance with the settlement. This is NOT a recall or a campaign, but is provided to reassure owners that Toyota stands behind the reliability of our vehicles.
Takata CSP Cover
Service Bulletin/Repair Instructions
CSP: Takata CSP Coverage Job Aid - published 7.28.2022
TSB001221Rev2
Service Bulletin/Repair Instructions
TSB: Some 2010 ? 2022 model year Toyota vehicles may exhibit paint stains after the removal of Rapgard?. The paint stains may appear to be under the clear coat but are usually under wrinkles in the Rapgard?. The wrinkles may trap water and cause the paint to stain from the trapped moisture, especially on horizontal surfaces such as the hood, roof, and trunk. Follow the Repair Procedure in this bulletin to address this condition
TSB009421Rev1
Service Bulletin/Repair Instructions
TSB: Some 2005 ? 2022 model year Toyota vehicles that have undergone water intrusion may exhibit a condition in which a musty smell is present. Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this service bulletin is to provide general guidelines and procedures for odor remediation. This service bulletin provides a guide on how to prepare the interior of the vehicle prior to an odor remediation being performed, as well as contact information for an approved vendor who will arrange the remediation, and instructions on how to prepare the interior of the vehicle for reassembly once the remediation has been completed. Refer to all model and model year specific Repair Manuals and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines. This service bulletin is to provide a general overview and direction for the odor remediation process
TTT063620
Service Bulletin/Repair Instructions
TT: Some Toyota vehicles installed with Toyota Complete Maintenance Care (TCMC) brake pads may exhibit a groan or squeak noise in various driving conditions
T-SB-0012-21 Rev
Service Bulletin/Repair Instructions
TSB: Some 2010 ? 2022 model year Toyota vehicles may exhibit paint stains after the removal of Rapgard?. The paint stains may appear to be under the clear coat but are usually under wrinkles in the Rapgard?. The wrinkles may trap water and cause the paint to stain from the trapped moisture, especially on horizontal surfaces such as the hood, roof, and trunk. Follow the Repair Procedure in this bulletin to address this condition
T-SB-0094-21
Service Bulletin/Repair Instructions
TSB: Some 2005 ? 2022 model year Toyota vehicles that have undergone water intrusion may exhibit a condition in which a musty smell is present. Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this service bulletin is to provide general guidelines and procedures for odor remediation. This service bulletin provides a guide on how to prepare the interior of the vehicle prior to an odor remediation being performed, as well as contact information for an approved vendor who will arrange the remediation, and instructions on how to prepare the interior of the vehicle for reassembly once the remediation has been completed. Refer to all model and model year specific Repair Manuals and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines. This service bulletin is to provide a general overview and direction for the odor remediation process.
T-SB-0088-21
Service Bulletin/Repair Instructions
TSB: For proper calibration of the millimeter wave radar sensor, the vehicle and radar target must be on a level surface with a consistent plane. If a level surface with a consistent plane is not available, use the Floor Slope Compensation Procedure in this service bulletin in conjunction with the appropriate model and model year Repair Manual instructions when adjusting the millimeter wave radar sensor.
T-TT-0578-19 Rev
Service Bulletin/Repair Instructions
TT: Some customers may encounter Bluetooth® connectivity concerns such as: ?Difficulty to pair the phone. ?Intermittent Bluetooth® failure to connect to the vehicle when first turning on the vehicle. ?Various Bluetooth® Audio functions are no longer functioning with customer?s phone such as ability to change the track using the steering wheel controls. These concerns can be caused by changes made on the customer?s phone. Make sure to inquire with the customer if the connectivity concerns occurred after receiving an operating system update on their phone, or if they have restored their phone data/settings recently.
T-SB-0080-19 Rev
Service Bulletin/Repair Instructions
TSB: Some 2006 ? 2022 model year Toyota vehicles in particular geographic areas may exhibit a condition where the HVAC evaporator drain hose has become obstructed with an insect nest. An insect repellent drain hose tip (ARINIX® Tip) is available to help minimize future occurrences of this environmental condition. For some models, a new drain hose is required to properly fit the ARINIX® Tip. Follow the procedures in this bulletin for proper handling and installation of this optional service part.
T-SB-0004-21 Rev
Service Bulletin/Repair Instructions
TSB: Some 2010 ? 2020 model year Sienna vehicles may exhibit a condition where the front door glass run on either the right-hand or left-hand side comes loose from the door channel during window operation. Follow the Repair Procedure in this bulletin to address this condition.
T-SB-0052-13 Obs
Service Bulletin/Repair Instructions
OBSOLETE NOTICE May 04, 2021: This bulletin is now obsolete. Please see T-SB-0004-21.
T-SB-0044-16 Obs
Service Bulletin/Repair Instructions
OBSOLETE NOTICE March 08, 2021: This bulletin is now obsolete. Please see T-SB-0012-21.
Toyota Safety Re
Service Bulletin/Repair Instructions
Toyota Safety Recall and Service Campaign - Technician Certification Requirements
T-TT-0636-20 Rev
Service Bulletin/Repair Instructions
TT: Some Toyota vehicles installed with Toyota Complete Maintenance Care (TCMC) brake pads may exhibit a groan or squeak noise in various driving conditions.
T-SB-0040-08 Obs
Service Bulletin/Repair Instructions
OBSOLETE NOTICE March 08, 2021: This bulletin is now obsolete. Please see T-SB-0044-16.
T-SB-0012-21
Service Bulletin/Repair Instructions
TSB: Some 2010 ? 2021 model year Toyota vehicles may exhibit paint stains after the removal of Rapgard?. The paint stains may appear to be under the clear coat but are usually under wrinkles in the Rapgard?. The wrinkles may trap water and cause the paint to stain from the trapped moisture, especially on horizontal surfaces such as the hood, roof, and trunk. Follow the Repair Procedure in this bulletin to address this condition.
T-SB-0032-20 Rev
Service Bulletin/Repair Instructions
TSB: Replacement certification labels (the vinyl label installed on the driver door or door post) and VIN plates (the metal plate riveted to dashboard) (see Figure 1) for most 1979 ? 2021 model year vehicles may be available provided the requests meet the criteria listed in this Service Bulletin. Follow the Procurement Procedure in this bulletin to request a replacement certification label or VIN plate.
T-SB-0004-21
Service Bulletin/Repair Instructions
TSB: Some 2010 ? 2020 model year Sienna vehicles may exhibit a condition where the front door glass run on either the right-hand or left-hand side comes loose from the door channel during window operation. Follow the Repair Procedure in this bulletin to address this condition.
T-TT-0636-20
Service Bulletin/Repair Instructions
TT: Some Toyota vehicles installed with Toyota Complete Maintenance Care (TCMC) brake pads may exhibit a groan or squeak noise in various driving conditions.
T-SB-0033-18 Rev
Service Bulletin/Repair Instructions
TSB: Some 2011 ? 2020 model year Sienna vehicles may exhibit a vibration/pulsation from the front brakes that can be felt in the brake pedal while lightly applying the brake pedal. Follow the Repair Procedure in this bulletin to address this condition.
T-TT-0628-20
Service Bulletin/Repair Instructions
TT: HVAC drain tube is found to be blocked/clogged.
T-TT-0468-17 Rev
Service Bulletin/Repair Instructions
TT: HVAC drain tube is found to be blocked/clogged.
T-SB-0063-20
Service Bulletin/Repair Instructions
TSB: SUPERSESSION NOTICE The information contained in this bulletin supersedes Service Bulletin Nos. ST005-01, SU001-08, and T-SB-0391-08. The aforementioned bulletins are obsolete, and any printed versions should be discarded. Be sure to review the entire content of this service bulletin before proceeding. This Service Bulletin provides best practice procedures for vehicle pulling complaint, diagnosis, and repair for 2002 ? 2021 model year Toyota vehicles. This information supplements Repair Manual procedures when the symptoms are: ?Vehicle Pulling: The vehicle moves to the right or left when the driver holds the steering wheel while driving straight ahead without exerting steering effort. ?Steering Wheel Off Center: The vehicle travels straight, but the steering wheel is not pointed straight ahead. The vehicle is not pulling. Before repairing a vehicle pulling to one side, it is necessary to clearly identify the cause of the pulling condition. Frequently, pulling to one side is diagnosed as a wheel alignment concern. However, the actual cause may be related to the lateral force generated by the tires, vehicle damage, road crown or worn components. Performing a wheel alignment when tire force is the cause could result in the wheel alignment being set at a value outside of specifications. This could then cause other problems such as uneven tire wear, etc. A customer may notice a pull to the left when in the left lanes of travel and notice a pull to the right or no pull when traveling in the right lanes of travel on the very same section of roadway. This road crown effect is environmental and cannot be corrected with suspension adjustments or any other wheel or tire modification discussed in this bulletin.
T-SB-0391-08 Obs
Service Bulletin/Repair Instructions
TSB: OBSOLETE NOTICE June 23, 2020: This bulletin is now obsolete. Please see T-SB-0063-20.
DOR-M9J4S-07
Service Bulletin/Repair Instructions
These SKUs are Exhaust Manifolds with Catalytic Converters. The customer communication requested return of unsold inventory due to a loss of CARB certification. These SKUs can no longer be sold as they do not meet CARB standards, but parts on vehicles are not effected.
T-SB-0304-17 Obs
Service Bulletin/Repair Instructions
TSB: OBSOLETE NOTICE April 07, 2020: This bulletin is now obsolete. Please see T-SB-0032-20. Replacement Certification Labels and VIN Plates
T-SB-0032-20
Service Bulletin/Repair Instructions
TSB: SUPERSESSION NOTICE The information contained in this bulletin supersedes Service Bulletin Nos. PG021-88, PG015-89, PG0015-90, PG002-91, PG002-93, PG005-97, PG007-01, PG007-07, PG006-01, PG004-97, T-SB-0144-08, and T-SB-0304-17. The aforementioned bulletins are obsolete, and any printed versions should be discarded. Replacement certification labels (the vinyl label installed on the driver door or door post) and VIN plates (the metal plate riveted to dashboard) (see Figure 1) for most 1979 ? 2020 model year vehicles may be available provided the requests meet the criteria listed in this Service Bulletin. Follow the Procurement Procedure in this bulletin to request a replacement certification label or VIN plate.
T-TT-0603-20
Service Bulletin/Repair Instructions
TT: For proper calibration of the millimeter wave radar sensor, the vehicle must be on a level surface. If a level surface is not available, this tech tip should be used in conjunction with the repair manual to set the angle of the front millimeter wave radar sensor and reflector height before performing beam axis adjustment.
T-SB-0142-13_Obs
Service Bulletin/Repair Instructions
OBSOLETE NOTICE February 12, 2020: This bulletin is now obsolete. Please see T-SB-0010-20.
T-SB-0010-20
Service Bulletin/Repair Instructions
TSB: Some 2004 ? 2017 model year Toyota vehicles may exhibit odors naturally occurring from the HVAC system and/or related environmental factors. Although there is no way to eliminate these odors, follow the General Procedure in this bulletin to minimize the odors experienced
T-SB-0008-20
Service Bulletin/Repair Instructions
TSB: Vehicles may display evidence of a fluid leak or fluid seep from powertrain components. This bulletin explains how to determine the differences between a fluid leak versus a fluid seep. Cases that are determined to be a ?leak? should be repaired accordingly and will be covered under warranty if applicable. Cases that are determined to be a ?seep? should be documented on the repair order and inspected at the next service interval. Follow the Repair Information in this bulletin to determine if the concern in question is a fluid leak or fluid seep and review the Repair Procedure section to address the condition. NOTE This bulletin applies to ALL powertrain fluids excluding fuel and coolant.
T-TT-0442-17_Rev
Service Bulletin/Repair Instructions
TT: Safety Connect is a vehicle option which requires a subscription fee for the system to be active after the initial trial period. Once the subscription has expired the DCM (Telematics Transceiver) will be in an inactive state. In some instances, a DCM may need to be replaced even though the customer is not using the service. If registration of the replacement DCM part is attempted using the Techstream utility after the account has become inactive, the registration will fail, and messages such as ?ATX webserver is Down? or ?ATX error? will be displayed.
KR3_Dealer Email
Service Bulletin/Repair Instructions
Dealer Email: Toyota will be sending Safety Recall/Special Service Campaign Follow-Up Notices to owners whose vehicles have not yet had the following Safety Recall/Special Service Campaign repairs completed. Please note the following information for Regional and PD associates.
KR3_Dealer Packa
Service Bulletin/Repair Instructions
Dealer Package: Toyota will be sending Safety Recall/Special Service Campaign Follow-Up Notices to owners whose vehicles have not yet had the following Safety Recall/Special Service Campaign repairs completed. Please note the following information for Regional and PD associates.
KR3_Region Email
Service Bulletin/Repair Instructions
Region Email: Toyota will be sending Safety Recall/Special Service Campaign Follow-Up Notices to owners whose vehicles have not yet had the following Safety Recall/Special Service Campaign repairs completed. Please note the following information for Regional and PD associates.
KR3_Region Lette
Service Bulletin/Repair Instructions
Region Letter: Toyota will be sending Safety Recall/Special Service Campaign Follow-Up Notices to owners whose vehicles have not yet had the following Safety Recall/Special Service Campaign repairs completed. Please note the following information for Regional and PD associates.
T-TT-0578-19
Service Bulletin/Repair Instructions
TT: Some customers may encounter Bluetooth® connectivity concerns such as: ? Difficulty to pair the phone. ? Intermittent Bluetooth® failure to connect to the vehicle when first turning on the vehicle. ? Various Bluetooth® Audio functions are no longer functioning with customer?s phone such as ability to change the track using the steering wheel controls. These concerns can be caused by changes made on the customer?s phone. Make sure to inquire with the customer if the connectivity concerns occurred after receiving an operating system update on their phone, or if they have restored their phone data/settings recently.
ZH5_Dealer Lette
Service Bulletin/Repair Instructions
Dealer Package: Toyota has received a number of reports regarding the power sliding door rear lock assemblies on certain 2011 ? 2018 model year Sienna vehicles. In these reports, corrosion on the position sensor of the left and/or right power sliding door rear lock assembly caused that door to exhibit one or more of the abnormal operations described below: ?During power mode closing operation, as the power sliding door reaches the nearly closed position, the door reverses and moves toward the open position. ?During power mode closing operation, the power sliding door cannot completely close and latch. ?The power mode closing operation of the power sliding door is inoperative. Although the power sliding door rear lock assemblies are covered by Toyota?s New Vehicle Limited Warranty for 3 years or 36,000 miles (whichever comes first), we at Toyota care about the customers? ownership experience. Toyota is now extending the warranty coverage for repairs relating to corrosion on the position sensor of the left and/or right power sliding door rear lock assembly that causes that door to exhibit one or more of the abnormal operations described above. The following information is provided to inform you and your staff of the program notification schedule and your degree of involvement.
ZKI_Dealer Packa
Service Bulletin/Repair Instructions
Dealer Package: This Customer Confidence Program is a component of a class action settlement that includes 3 elements of coverage, including prospective coverage for repairs to certain sliding door parts but only those repairs that relate to internal functional concerns of those parts on certain 2011 - 2018 model year Sienna vehicles.
T-SB-0033-14-Obs
Service Bulletin/Repair Instructions
TSB: OBSOLETE NOTICE July 9, 2019: This bulletin is now obsolete. Please see T-SB-0080-19.
T-SB-0080-19
Service Bulletin/Repair Instructions
TSB: SUPERSESSION NOTICE The information contained in this bulletin supersedes Service Bulletin No. T-SB-0033-14. ? Applicability has been updated to include 2019 model year Toyota vehicles. Service Bulletin No. T-SB-0033-14 is obsolete and any printed versions should be discarded. Some 2006 ? 2019 model year Toyota vehicles in particular geographic areas may exhibit a condition where the HVAC evaporator drain hose has become obstructed with an insect nest. An insect repellent drain hose tip (ARINIX® Tip) is available to help minimize future occurrences of this environmental condition. For some models, a new drain hose is required to properly fit the ARINIX® Tip. Follow the procedures in this bulletin for proper handling and installation of this optional service part. NOTE The ARINIX® Tip is NOT registered or labeled for sale or use outside the United States or Puerto Rico.
T-SB-0076-19
Service Bulletin/Repair Instructions
TSB: Some 2009 ? 2019 model year Toyota vehicles with super chrome wheel finishes may become discolored and/or damaged when aftermarket cleaners, polishes, or brake dust removal products are used on wheels with super chrome finishes. Wheel cleaners and polish that contain acidic substances may damage the clear coat of the wheel, resulting in the undercoating (black) to become visible.
T-SB-0134-16-Rev
Service Bulletin/Repair Instructions
TSB: REVISION NOTICE July 01, 2019 Rev2: ? Applicability has been updated to 2019 ? 2020 model year Toyota vehicles. ? The Techstream Preparation and Process Overview sections have been updated. October 30, 2017 Rev1: ? Applicability has been updated to include 2018 model year vehicles. Any previous printed versions of this bulletin should be discarded. SUPERSESSION NOTICE The information contained in this bulletin supersedes SB No. T-SB-0012-13. Service Bulletin No. T-SB-0012-13 is obsolete and any printed versions should be discarded. Be sure to review the entire content of this bulletin before proceeding. Flash reprogramming allows the Electronic Control Unit (ECU) software to be updated without replacing the ECU. Flash calibration updates for specific vehicle models/ECUs are released as field-fix procedures described in individual Service Bulletins. This bulletin details the Techstream ECU flash reprogramming process and outlines use of the Technical Information System (TIS) and the Calibration Update Wizard (CUW). Flash calibration updates can only be applied to the vehicle/ECU combination for which they are intended. ECUs have internal security that will not allow them to be programmed with another ECU?s information. NOTE ECU is a Toyota term used to describe integrated computerized devices responsible for managing the operation of a system or subsystem. For the purposes of this bulletin, the term ?ECU? is used as a generic label for the following SAE J1930 standard references: ? Powertrain Control Module (PCM) ? Engine Control Module (ECM) ? Transmission Control Module (TCM) ? Any other Toyota specific control unit
ZH5_Toyota POL17
Service Bulletin/Repair Instructions
Customer Support Program: Toyota has received a number of reports regarding the power sliding door rear lock assemblies on certain 2011?2018 model year Sienna vehicles. In these reports, corrosion on the position sensor of the left and/or right power sliding door rear lock assembly caused that door to exhibit one or more of the abnormal operations described below: ? During power mode closing operation, as the power sliding door reaches the nearly closed position, the door reverses and moves toward the open position. ? During power mode closing operation, the power sliding door cannot completely close and latch. ? The power mode closing operation of the power sliding door is inoperative.
ZKF_Toyota POL19
Service Bulletin/Repair Instructions
Customer Support Program: In our continuing efforts to ensure the best in customer satisfaction, and pursuant to a proposed class action settlement, Toyota is announcing a Customer Support Program to provide coverage for the sliding door center hinge assembly. Although the sliding door center hinge assembly is covered by Toyota?s New Vehicle Limited Warranty for 3 years or 36,000 miles (whichever occurs first), we at Toyota care about each customer?s ownership experience. Toyota is providing additional coverage for repairs related to sliding door center hinge assembly. Only those repairs that are related to internal functional concerns of the sliding door center hinge assembly that impede the closing and/or opening operations of the sliding door in manual and/or power modes are covered. The following information is provided to inform you and your staff of the program notification schedule and your degree of involvement.
T-SB-0066-19
Service Bulletin/Repair Instructions
TSB: Some 2011 ? 2018 model year Sienna vehicles equipped with manual doors may exhibit a condition where the slide door center hinge has corroded, causing the slide door to become difficult to operate while opening or closing. Follow the Inspection and Repair Procedures in this bulletin to address this condition.
T-SB-0067-19
Service Bulletin/Repair Instructions
TSB: Some 2011 ? 2018 model year Sienna vehicles equipped with power slide doors may exhibit a condition where the slide door center hinge has corroded, causing the power slide door to not fully open or close during operation. Follow the Inspection Procedure and Repair Procedure in this bulletin to address this condition.
T-SB-0068-19
Service Bulletin/Repair Instructions
TSB: Some 2011 ? 2018 model year Sienna vehicles may exhibit a condition where the fuel lid door is loose or not flush against the vehicle body, which may prevent the driver side slide door from opening. This condition may be caused by a broken fuel lid door hinge. Follow the Repair Procedure in this bulletin to address this condition.
T-SB-0069-19
Service Bulletin/Repair Instructions
TSB: Some 2011 ? 2018 model year Sienna customers may express concern about their vehicle?s slide door performance. Upon customer request, the Inspection Procedure in this bulletin may be performed for a functional check of the slide door system.
T-SB-0141-18_Rev
Service Bulletin/Repair Instructions
TSB: REVISION NOTICE June 19, 2019 Rev1: ? The Parts Information section has been updated. Any previous printed versions of this bulletin should be discarded. Some 2011 ? 2018 model year Sienna vehicles may exhibit a condition where the power slide door cable becomes separated, causing the power slide door to become inoperative. Follow the Repair Procedure in this bulletin to reduce this condition.
ZH4_Dealer Packa
Service Bulletin/Repair Instructions
Dealer Package: June 19, 2019 Information about a proposed class action settlement has been added. ? Toyota has expanded the covered vehicle population. ? Toyota has extended the coverage period by one additional year. In our continuing efforts to ensure the best in customer satisfaction, and pursuant to a class action settlement, Toyota is announcing a Customer Support Program to extend the warranty coverage for the sliding door front lock assemblies on certain 2011 ? 2018 model year Sienna vehicles.
ZH4_Toyota POL17
Service Bulletin/Repair Instructions
Customer Support Program: Toyota has received a number of reports regarding sliding door front lock assemblies on certain 2011?2018 model year Sienna vehicles. In these reports, during the closing operation of the left and/or right side sliding door, the door would not completely close and latch due to corrosion on the latch lever pin of the door?s front lock assembly.
ZH5_Dealer Packa
Service Bulletin/Repair Instructions
Dealer Package: June 19, 2019 Information about a proposed class action settlement has been added. ? Toyota has expanded the covered vehicle population. ? Toyota has extended the coverage period by one additional year. In our continuing efforts to ensure the best in customer satisfaction, and pursuant to a class action settlement, Toyota is announcing a Customer Support Program to extend the warranty coverage for the power sliding door rear lock assemblies on certain 2011 ? 2018 model year Sienna vehicles.
ZKD_Dealer Packa
Service Bulletin/Repair Instructions
Dealer Package: Certain 2011 ? 2018 Model Year Sienna Vehicles Coverage for the Power Sliding Door Cable Sub-Assembly (Vehicles equipped with power sliding doors ONLY). In our continuing efforts to ensure the best in customer satisfaction, and pursuant to a class action settlement, Toyota is announcing a Customer Support Program to provide coverage for repairs to the power sliding door cable sub-assembly. Although the power sliding door cable sub-assemblies are covered by Toyota?s New Vehicle Limited Warranty for 3 years or 36,000 miles (whichever comes first), we at Toyota care about the customers? ownership experience. Toyota is providing coverage for repairs to the power sliding door cable sub-assembly. Only those repairs that are related to internal functional concerns of the power sliding door cable sub-assembly that impede the closing and/or opening operations of the power sliding door in manual and/or power modes are covered. The following information is provided to inform you and your staff of the program notification schedule and your degree of involvement.
ZKD_Toyota POL19
Service Bulletin/Repair Instructions
Customer Program Support: In our continuing efforts to ensure the best in customer satisfaction, and pursuant to a proposed class action settlement, Toyota is announcing a Customer Support Program to provide coverage for the power sliding door cable sub-assembly. Although the power sliding door cable sub-assemblies are covered by Toyota?s New Vehicle Limited Warranty for 3 years or 36,000 miles (whichever occurs first), we at Toyota care about each customer?s ownership experience. Toyota is providing additional coverage for repairs related to the power sliding door cable sub-assembly. Only those repairs that are related to internal functional concerns of the power sliding door cable sub-assembly that impede the closing and/or opening operations of the power sliding door in manual and/or power modes are covered. The following information is provided to inform you and your staff of the program notification schedule and your degree of involvement.
ZKE_Dealer Packa
Service Bulletin/Repair Instructions
Dealer Package: Certain 2011 ? 2018 Model Year Sienna Vehicles Coverage for the Fuel Filler Door Hinge and Pin. In our continuing efforts to ensure the best in customer satisfaction, and pursuant to a class action settlement, Toyota is announcing a Customer Support Program to provide coverage for repairs to the fuel filler door hinge and pin. Although the fuel filler door hinge and pin are covered by Toyota?s New Vehicle Limited Warranty for 3 years or 36,000 miles (whichever comes first), we at Toyota care about the customers? ownership experience. Toyota is providing coverage for repairs to the fuel filler door hinge and pin. Only those repairs that are related to internal functional concerns of the fuel filler door hinge and pin that impede the closing and/or opening operations of the sliding door in manual and/or power modes are covered. The following information is provided to inform you and your staff of the program notification schedule and your degree of involvement.
ZKE_Toyota POL19
Service Bulletin/Repair Instructions
Customer Support Program: In our continuing efforts to ensure the best in customer satisfaction, and pursuant to a proposed class action settlement, Toyota is announcing a Customer Support Program to provide coverage for the fuel filler door hinge and pin. Although the fuel filler door hinge and pin are covered by Toyota?s New Vehicle Limited Warranty for 3 years or 36,000 miles (whichever occurs first), we at Toyota care about each customer?s ownership experience. Toyota is providing additional coverage for repairs related to the fuel filler door hinge and pin. Only those repairs that are related to internal functional concerns of the fuel filler door hinge and pin that impede the closing and/or opening operations of the power sliding door in manual and/or power modes are covered. The following information is provided to inform you and your staff of the program notification schedule and your degree of involvement.
ZKF_Dealer Packa
Service Bulletin/Repair Instructions
Dealer Package: Certain 2011 ? 2018 Model Year Sienna Vehicles Coverage for the Sliding Door Center Hinge Assembly. In our continuing efforts to ensure the best in customer satisfaction, and pursuant to a class action settlement, Toyota is announcing a Customer Support Program to provide coverage for repairs to the sliding door center hinge assembly. Although the sliding door center hinge assembly is covered by Toyota?s New Vehicle Limited Warranty for 3 years or 36,000 miles (whichever comes first), we at Toyota care about the customers? ownership experience. Toyota is providing coverage for repairs to the sliding door center hinge assembly. Only those repairs that are related to internal functional concerns of the sliding door center hinge assembly that impede the closing and/or opening operations of the sliding door in manual and/or power modes are covered. The following information is provided to inform you and your staff of the program notification schedule and your degree of involvement.
ZKI_Dealer Email
Service Bulletin/Repair Instructions
Dealer Email: In our continuing efforts to ensure the best in customer satisfaction, and pursuant to a Sienna sliding door class action settlement, Toyota is announcing a Customer Confidence Program. The following information is provided to inform you and your staff of the program notification schedule and your degree of involvement.
ZKI_Region Email
Service Bulletin/Repair Instructions
Region Email: In our continuing efforts to ensure the best in customer satisfaction, and pursuant to a Sienna sliding door class action settlement, Toyota is announcing a Customer Confidence Program. The following information is provided to inform you and your staff of the program notification schedule and your degree of involvement.
ZKI_Region Lette
Service Bulletin/Repair Instructions
Region Letter: Certain 2011 - 2018 Model Year Sienna Vehicles Coverage for Certain Internal Functional Concerns of Certain Sliding Door Parts. Specific information for Region support is provided below. In our continuing efforts to ensure the best in customer satisfaction, and pursuant to a Sienna sliding door class action settlement, Toyota is announcing a Customer Confidence Program. The following information is provided to inform you and your staff of the program notification schedule and your degree of involvement.
ZKJ_Dealer Packa
Service Bulletin/Repair Instructions
Dealer Package: Certain 2011 - 2018 Model Year Sienna Vehicles Sienna Sliding Door Functional Inspection. This Sienna Sliding Door Functional Inspection is one of multiple elements involved in a class action settlement. Refer to Customer Confidence Program ZKI for comprehensive information on the class action settlement and its other elements.
TSR-SC-032819
Service Bulletin/Repair Instructions
Technician Certification Requirements.
Sienna Sliding D
Service Bulletin/Repair Instructions
Dealer Daily Message: Sienna Sliding Door Certain 2011 ? 2018 Model Year Sienna Vehicles ? A court has preliminarily approved a proposed settlement regarding sliding doors on certain 2011-2018 model year Sienna vehicles. ? The proposed settlement has yet to receive final approval by the court. However, the proposed settlement allows Toyota to implement the Customer Confidence Program (as outlined in the settlement agreement) in advance of the proposed settlement becoming final. Accordingly, Toyota has decided to implement certain components of the Customer Confidence Program in advance of final approval. These components are listed below and Toyota estimates that they will be available starting in April 2019.1 At that time, Toyota will issue a notice to all dealers advising them that these components have become available. Pursuant to the proposed settlement?s Customer Confidence Program: o Coverage for repairs to the power sliding door cable sub-assembly, sliding door center hinge assembly, and fuel door will be available for 10 years from the subject vehicles date of first use, regardless of mileage. o Warranty Enhancement Program ZH4 will be expanded to include certain 2016 ? 2018 model year Sienna vehicles. o Warranty Enhancement Program ZH5 will be expanded to include certain 2015 ? 2018 model year Sienna vehicles. o Warranty Enhancement Programs ZH4 and ZH5, which are applicable for nine years from the subject vehicles date of first use regardless of mileage, will be extended by one additional year regardless of mileage. ? The court has ordered that the 3rd Party Settlement Notice Administrator begin notifying class members, including by direct mail notice (see images on next page), on March 1, 2019, to inform current and former vehicle owners and lessees of the proposed settlement.
T-TT-0414-16-Rev
Service Bulletin/Repair Instructions
TT: Some customers may encounter Bluetooth® connectivity concerns such as: ? Difficulty to pair the phone. ? Intermittent Bluetooth® failure to connect to the vehicle when first turning on the vehicle. ? Various Bluetooth® Audio functions are no longer functioning with customer?s phone such as ability to change the track using the steering wheel controls. These concerns can be caused by changes made on the customer?s phone. Make sure to inquire with the customer if the connectivity concerns occurred after receiving an operating system update on their phone, or if they have restored their phone data/settings recently.
T-TT-0468-17-Rev
Service Bulletin/Repair Instructions
TT: HVAC drain tube is found to be blocked/clogged.
T-SB-0044-16_Rev
Service Bulletin/Repair Instructions
TSB: REVISION NOTICE February 7, 2019 Rev2: * Applicability has been updated to include 2010 - 2014 model year Matrix, 2017 - 2019 model year C-HR, 2019 model year Corolla Hatchback, and 2018 - 2019 model year Toyota vehicles. G418 The Introduction and Repair Procedure sections have been updated. March 7, 2017 Rev1: * Applicability has been updated to include 2017 model year Toyota vehicles. Any previous printed versions of this bulletin should be discarded. SUPERSESSION NOTICE The information contained in this bulletin supersedes SB No. T-SB-0040-08. * Applicability has been updated to include applicable 2016 model year vehicles. Service Bulletin No. T-SB-0040-08 is obsolete and any printed versions should be discarded. Some 2010 - 2019 model year Toyota vehicles may exhibit paint stains after the removal of Rapgard. The paint stains may appear to be under the clear coat but are usually under wrinkles in the Rapgard. The wrinkles may trap water and cause the paint to stain from the trapped moisture, especially on horizontal surfaces, such as the hood, roof, and trunk. Follow the Repair Procedure in this bulletin to address this condition.
T-SB-0033-14_Rev
Service Bulletin/Repair Instructions
TSB: Some vehicles in particular geographic areas may exhibit a condition where the HVAC evaporator drain hose has become obstructed with an insect nest. An insect repellent drain hose tip (ARINIX® Tip) is now available to help minimize future occurrences of this environmental condition. For some models, a new drain hose is required to properly fit the ARINIX® Tip. Follow the procedures in this bulletin for proper handling and installation of this optional service part.
T-SB-0141-18
Service Bulletin/Repair Instructions
TSB: Some 2011 ? 2018 model year Sienna vehicles may exhibit a condition where the power sliding door cable becomes separated, causing the power sliding door to become inoperative. Follow the Repair Procedure in this bulletin to reduce this condition.
T-SB-0244-17_Rev
Service Bulletin/Repair Instructions
TSB: REVISION NOTICE November 14, 2018 Rev1: ? The Diagnosis Procedure and Repair Procedure sections have been updated. Any previous printed versions of this bulletin should be discarded. Some 2011 ? 2018 model year Sienna vehicles may exhibit a condition where the slide door?s ?power or manual ? front and rear latches may not latch simultaneously due to corrosion on the latch lever pin of the front lock assembly. Additionally, some 2011 ? 2015 model year Sienna vehicles may exhibit a condition where the power slide door does not close properly due to internal corrosion in the latch switch of the rear lock assembly. Follow the procedures in this bulletin to address these conditions.
TS-WI-0290
Service Bulletin/Repair Instructions
Service Bulletin sent to all dealers to inspect L-track bolts for correct torque and to incorporate torque check as part of regular maintenance
PG004-97-Obsolet
Service Bulletin/Repair Instructions
Technical Service Bulletin: OBSOLETE NOTICE: July 31, 2018: This bulletin is now obsolete. Please see T-SB-0304-17.
PG006-01-Obsolet
Service Bulletin/Repair Instructions
Technical Service Bulletin: OBSOLETE NOTICE: July 31, 2018: This bulletin is now obsolete. Please see T-SB-0304-17.
T-SB-0304-17_Rev
Service Bulletin/Repair Instructions
TSB: REVISION NOTICE July 31, 2018 Rev2: ? The Supersession Notice has been updated. January 11, 2018 Rev1: ? The Supersession Notice has been updated. Any previous printed versions of this bulletin should be discarded. SUPERSESSION NOTICE The information contained in this bulletin supersedes Service Bulletin Nos. PG021-88, PG015-89, PG0015-90, PG002-91, PG002-93, PG005-97, PG007-01, PG007-07, PG006-01, PG004-97, and T-SB-0144-08. Service Bulletin Nos. PG021-88, PG015-89, PG0015-90, PG002-91, PG002-93, PG005-97, PG007-01, PG007-07, PG006-01, PG004-97, and T-SB-0144-08 are obsolete and any printed versions should be discarded. Vehicle replacement certification labels (the vinyl label installed on the driver door or door post) and VIN plates (the metal plate riveted to dashboard) may be available from Toyota, provided the request meets one of the criteria listed in this Service Bulletin. Replacement Certification Label and VIN Plate Criteria A replacement certification label and/or VIN plate may be requested if: ? The vehicle was in an accident and the label and/or plate is damaged or attached to a part that will be replaced during the repair. ? The label and/or plate was stolen.
ZG5_Toyota POL17
Service Bulletin/Repair Instructions
Warranty Policy Bulletin: Toyota has received reports of customer concerns in which the power moon roof, power sliding doors or power hatch are inoperative from the overhead console switches or require excessive pressure on the overhead console switches to operate. Due to parts availability this Warranty Enhancement Program will be launched in 2 phases as illustrated below: 1 Camry and Camry Hybrid Certain 2012 March, 2017 Repair, Available 2 Sienna Certain 2011-2013 June, 2017 Repair Available.
T-SB-0045-14_Obs
Service Bulletin/Repair Instructions
TSB: OBSOLETE NOTICE May 10, 2018: This bulletin is now obsolete. Please see T-SB-0033-18.
T-TT-0497-18
Service Bulletin/Repair Instructions
TT: Some vehicles may experience a condition in which the 2nd row seat, with center seat, exhibits a chirp/squeak noise from the rear seat latches (floor area). This condition is present while driving over rough or bumpy roads. Upon further inspection, after removal of the LH 2nd row seat, the rear inboard and outboard strikers may show signs of the coating peeling off as shown in Fig.2 and Fig.3.
T-SB-0033-18
Service Bulletin/Repair Instructions
TSB: SUPERSESSION NOTICE The information contained in this bulletin supersedes Service Bulletin No. T-SB-0045-14. * Applicability has been updated to include 2018 model year Sienna vehicles. * The entire bulletin has been updated. Service Bulletin No. T-SB-0045-14 is obsolete and any printed versions should be discarded. Some 2011 - 2018 model year Sienna vehicles may exhibit a vibration/pulsation from the front brakes that can be felt in the brake pedal while lightly applying the brake pedal. Follow the Repair Procedure in this bulletin to address this condition.
T-SB-0187-12_Rev
Service Bulletin/Repair Instructions
TSB: REVISION NOTICE February 12, 2018 Rev2: ? Applicability has been updated to include 2015 ? 2018 model year vehicles. January 23, 2014 Rev1: ? Applicability has been updated to include 2013 ? 2014 model year vehicles. Any previous printed versions of this bulletin should be discarded. Toyota vehicles are equipped with either conventional or run-flat tires. Sometimes punctures may occur as a result of contact with road debris or other hazards. If a puncture occurs, it may be possible to repair the tire and return it to service. With a conventional tire it is not possible to drive for an extended amount of time with the tire at low pressures as damage to the tire may occur. With run-flat tires, due to reinforced sidewalls, it is possible to drive for up to 100 miles at speeds less than 55 mph with little or no damage to the tire. The U.S. Tire Manufacturers Association (UTSMA) provides guidelines and recommendations for tire repair and replacement. It also provides information related to: ? Basic tire information ? Tire maintenance and safety ? Driver education, tire safety curriculum.
T-SB-0009-18
Service Bulletin/Repair Instructions
TSB: The purpose of this Service Bulletin is to elevate awareness and provide best practices for leather and synthetic leather care in Toyota vehicles. As an additional resource, if the vehicle is equipped with factory leather seats, the vehicle Owner?s Manual will highlight the importance of proper maintenance and provide guidance for care.
TS-WI-0256
Service Bulletin/Repair Instructions
Service Bulletin sent to all dealers to update the firmware in the affected vehicles VMI computer. This allows for more amperage to draw the Powerkneel up allowing the up-limit switch to be tripped consistently. If the up limit switch is not engaged, a vehicle may not come out of park or the conversion may not operate properly next time it is deployed
TSR-1212-17
Service Bulletin/Repair Instructions
Technician Certification Requirements.
T-SB-0229-12_Rev
Service Bulletin/Repair Instructions
TSB: REVISION NOTICE November 22, 2017 Rev1: ? Applicability has been updated to include 2014 ? 2018 model year vehicles. Any previous printed versions of this bulletin should be discarded. In the event that a Toyota vehicle becomes submerged in water, many components may be physically damaged. Electrical and electronic components, including wiring harnesses, are particularly susceptible to corrosion and subsequent malfunction. Although any flooding can be damaging, salt water flooding elevates the potential for abnormal conditions and may increase risks due to its highly corrosive and conductive nature. Salt residue also continues to corrode and remain conductive even after a vehicle dries. This bulletin is intended to assist with safe handling and inspection of flood damaged vehicles and to provide basic guidance on likely needed repairs.
T-SB-0134-16_Rev
Service Bulletin/Repair Instructions
TSB: REVISION NOTICE October 30, 2017 Rev1: * Applicability has been updated to include 2018 model year vehicles. SUPERSESSION NOTICE The information contained in this bulletin supersedes SB No. T-SB-0012-13. Flash reprogramming allows the Electronic Control Unit (ECU) software to be updated without replacing the ECU. Flash calibration updates for specific vehicle models/ECUs are released as field-fix procedures described in individual Service Bulletins. This bulletin details the Techstream ECU flash reprogramming process and outlines use of the Technical Information System (TIS) and the Calibration Update Wizard (CUW). Flash calibration updates can only be applied to the vehicle/ECU combination for which they are intended. ECUs have internal security that will not allow them to be programmed with another ECU's information.
T-SB-0304-17
Service Bulletin/Repair Instructions
TSB: Vehicle replacement certification labels (the vinyl label installed on the driver door or door post) and VIN plates (the metal plate riveted to dashboard) may be available from Toyota, provided the request meets one of the criteria listed in this Service Bulletin.
E0N_Dealer Lette
Service Bulletin/Repair Instructions
Dealer Letter: October 23, 2017 A watermark has been added to the Dealer Letter to indicate that E0N expired on June 30, 2017.
E0N_Expired LSC_
Service Bulletin/Repair Instructions
TI: Technical Instructions for Limited Service Campaign E0N Driving Support ECU Certain 2011-2014 Model Year Sienna.
T-TT-0453-17-Rev
Service Bulletin/Repair Instructions
TT: Previously, an error message was received when performing DCM activation initiated by Techstream. This condition has been remedied, and DCM activation utilizing Techstream can now be resumed.
T-SB-0045-14_Rev
Service Bulletin/Repair Instructions
TSB: REVISION NOTICE September 19, 2017 Rev2: ? Applicability has been updated to include 2017 model year Sienna vehicles. August 2, 2016 Rev1: ? Applicability has been updated to include 2015 ? 2016 model year Sienna vehicles. Any previous printed versions of this bulletin should be discarded. Some 2011 ? 2017 model year Sienna vehicles may exhibit a vibration/pulsation from the front brakes that can be felt in the brake pedal while lightly applying the brake pedal. Follow the Repair Procedure in this bulletin to address this condition.
T-TT-0453-17
Service Bulletin/Repair Instructions
TT: An error message is received when performing DCM activation initiated by Techstream. This is a known condition and will be remedied in the near future. Please discontinue DCM activations utilizing Techstream until further notice.
ZH4_Dealer Daily
Service Bulletin/Repair Instructions
Dealer Daily Message: Extension of Warranty Coverage for the Sliding Door Front Lock Assemblies. The Dealer Letter for Warranty Enhancement Program ZH4 is now available on TIS.
ZH4_Dealer Email
Service Bulletin/Repair Instructions
Dealer Email: Toyota has received a number of reports regarding sliding door front lock assemblies on certain 2011 ? 2016 model year Sienna vehicles. In these reports, during the closing operation of the left and/or right side sliding door, the door would not completely close and latch due to corrosion on the latch lever pin of the door?s front lock assembly.
ZH4_Dealer Lette
Service Bulletin/Repair Instructions
Dealer Letter: Toyota has received a number of reports regarding sliding door front lock assemblies on certain 2011 ? 2016 model year Sienna vehicles. In these reports, during the closing operation of the left and/or right side sliding door, the door would not completely close and latch due to corrosion on the latch lever pin of the door?s front lock assembly.
ZH4_Region Email
Service Bulletin/Repair Instructions
Region Email: Toyota has received a number of reports regarding sliding door front lock assemblies on certain 2011 ? 2016 model year Sienna vehicles. In these reports, during the closing operation of the left and/or right side sliding door, the door would not completely close and latch due to corrosion on the latch lever pin of the door?s front lock assembly.
ZH4_Region Lette
Service Bulletin/Repair Instructions
Region Letter: Toyota has received a number of reports regarding sliding door front lock assemblies on certain 2011 ? 2016 model year Sienna vehicles. In these reports, during the closing operation of the left and/or right side sliding door, the door would not completely close and latch due to corrosion on the latch lever pin of the door?s front lock assembly.
ZH5_Dealer Daily
Service Bulletin/Repair Instructions
Dealer Daily Message: Extension of Warranty Coverage for the Power Sliding Door Rear Lock Assemblies. The Dealer Letter for Warranty Enhancement Program ZH5 is now available on TIS.
ZH5_Dealer Email
Service Bulletin/Repair Instructions
Dealer Email: Toyota has received a number of reports regarding the power sliding door rear lock assemblies on certain 2011 ? 2015 model year Sienna vehicles. In these reports, corrosion on the position sensor of the left and/or right power sliding door rear lock assembly caused that door to exhibit one or more of the abnormal operations described below: ? During power mode closing operation, as the power sliding door reaches the nearly closed position, the door reverses and moves toward the open positon. ? During power mode closing operation, the power sliding door cannot completely close and latch. ? The power mode closing operation of the power sliding door is inoperative.
ZH5_Region Email
Service Bulletin/Repair Instructions
Region Email: Toyota has received a number of reports regarding the power sliding door rear lock assemblies on certain 2011 ? 2015 model year Sienna vehicles. In these reports, corrosion on the position sensor of the left and/or right power sliding door rear lock assembly caused that door to exhibit one or more of the abnormal operations described below: ? During power mode closing operation, as the power sliding door reaches the nearly closed position, the door reverses and moves toward the open positon. ? During power mode closing operation, the power sliding door cannot completely close and latch. ? The power mode closing operation of the power sliding door is inoperative.
ZH5_Region Lette
Service Bulletin/Repair Instructions
Region Letter: Toyota has received a number of reports regarding the power sliding door rear lock assemblies on certain 2011 ? 2015 model year Sienna vehicles. In these reports, corrosion on the position sensor of the left and/or right power sliding door rear lock assembly caused that door to exhibit one or more of the abnormal operations described below: ? During power mode closing operation, as the power sliding door reaches the nearly closed position, the door reverses and moves toward the open positon. ? During power mode closing operation, the power sliding door cannot completely close and latch. ? The power mode closing operation of the power sliding door is inoperative.
T-SB-0244-17
Service Bulletin/Repair Instructions
TSB: Some 2011 ? 2016 model year Sienna vehicles may exhibit power or manual sliding door front and rear latches simultaneously NOT latching due to corrosion on the latch lever pin of the front lock assembly. Additionally, some 2011 ? 2015 model year Sienna vehicles may exhibit power sliding door abnormal closing operation due to internal corrosion in the latch switch of the rear lock assembly.
T-SB-0232-17
Service Bulletin/Repair Instructions
TSB: Some 2014 - 2017 model year Highlander/Highlander HV and 2011 - 2017 model year Sienna vehicles equipped with a Power Back Door (PBD) may exhibit a condition in which the back door latch does not release and the PBD cannot be opened from any switch (IP, key, back door), with one or both of the following conditions: * Excessive force required to operate the manual back door latch release lever * DTC B2250 present.
ZG5_Dealer Email
Service Bulletin/Repair Instructions
Dealer Email: Toyota has received a number of reports regarding the Overhead Console Switch Assembly operation in Certain 2012 Model Year Camry, Camry Hybrid, and Certain 2011 ? 2013 Model Year Sienna vehicles. In these reports, customers have indicated the switches become inoperative or require excessive pressure to operate.
ZG5_Dealer Lette
Service Bulletin/Repair Instructions
Dealer Letter: Toyota has received a number of reports regarding the Overhead Console Switch Assembly operation in Certain 2012 Model Year Camry, Camry Hybrid, and Certain 2011 - 2013 Model Year Sienna vehicles. In these reports, customers have indicated the switches become inoperative or require excessive pressure to operate.
ZG5_Region Email
Service Bulletin/Repair Instructions
Region Email: Toyota has received a number of reports regarding the Overhead Console Switch Assembly operation in Certain 2012 Model Year Camry, Camry Hybrid, and Certain 2011 ? 2013 Model Year Sienna vehicles. In these reports, customers have indicated the switches become inoperative or require excessive pressure to operate.
ZG5_Region Lette
Service Bulletin/Repair Instructions
Region Letter: Toyota has received a number of reports regarding the Overhead Console Switch Assembly operation in Certain 2012 Model Year Camry, Camry Hybrid, and Certain 2011 ? 2013 Model Year Sienna vehicles. In these reports, customers have indicated the switches become inoperative or require excessive pressure to operate.
T-TT-0442-17
Service Bulletin/Repair Instructions
TT: Safety Connect is a vehicle option which requires a subscription fee for the system to be active. The first year of service is provided in the vehicle purchase price. Once the subscription has expired the DCM (Telematics Transceiver) will be in an inactive state. In some instances, a DCM may need to be replaced even though the customer is not using the service.
T-SB-0207-17
Service Bulletin/Repair Instructions
TSB: Some North American produced RAV4, Highlander, Highlander HV, and Sienna vehicles equipped with manual front seats may exhibit an inoperative forward/rearward adjustment function. Upon closer inspection it may be noticed that the Seat Track Adjusting Handle has become disengaged from the locking levers. APPLICABLE WARRANTY: This repair is covered under the Toyota Basic Warranty. This warranty is in effect for 36 months or 36,000 miles, whichever occurs first, from the vehicle's in-service date. Warranty application is limited to occurrence of the specified condition described in this bulletin.
T-SB-0208-17
Service Bulletin/Repair Instructions
TSB: Some 2011 ? 2016 model year Sienna vehicles may exhibit Sliding Door Front and Rear Latches simultaneously NOT latching due to the PSD 25 Amp fuse becoming open. APPLICABLE WARRANTY: This repair is covered under the Toyota Basic Warranty. This warranty is in effect for unlimited mileage and unlimited months of service. Warranty application is limited to occurrence of the specified condition described in this bulletin.
ZG5 Dealer Daily
Service Bulletin/Repair Instructions
Dealer Daily Message: Warranty Enhancement Program ? ZG5 Certain 2012 Model Year Camry and Camry Hybrid Vehicles Certain 2011 ? 2013 Model Year Sienna Vehicles Extension of Warranty Coverage for Overhead Console Switch Assembly.
ZG5 Dealer Email
Service Bulletin/Repair Instructions
Dealer Email: Toyota is announcing a Warranty Enhancement Program to extend the warranty coverage on the Overhead Console Switch Assembly on Certain 2012 Model Year Camry, Camry Hybrid, and Certain 2011 ? 2013 Model Year Sienna vehicles.
ZG5 Dealer Packa
Service Bulletin/Repair Instructions
Dealer Package: Toyota is announcing a Warranty Enhancement Program to extend the warranty coverage on the Overhead Console Switch Assembly on Certain 2012 Model Year Camry, Camry Hybrid, and Certain 2011 ? 2013 Model Year Sienna vehicles.
ZG5 Region Email
Service Bulletin/Repair Instructions
Region Email: Toyota is announcing a Warranty Enhancement Program to extend the warranty coverage on the Overhead Console Switch Assembly on Certain 2012 Model Year Camry, Camry Hybrid, and Certain 2011 ? 2013 Model Year Sienna vehicles.
ZG5 Region Lette
Service Bulletin/Repair Instructions
Region Letter: Toyota has received a number of reports regarding the Overhead Console Switch Assembly operation in Certain 2012 Model Year Camry, Camry Hybrid, and Certain 2011 ? 2013 Model Year Sienna vehicles. In these reports, customers have indicated the switches become inoperative or require excessive pressure to operate.
ZG5_POL17-01_War
Service Bulletin/Repair Instructions
Warranty Policy Bulletin POL17-01: Toyota has received reports of customer concerns in which the power moon roof, power sliding doors or power hatch are inoperative from the overhead console switches or require excessive pressure on the overhead console switches to operate. Due to parts availability this Warranty Enhancement Program will be launched in 2 phases.
T-TT-0435-17
Service Bulletin/Repair Instructions
TT: This bulletin is regarding best practices when handling navigation systems that use Hard Disc Drive or Micro SD Card memory.
TSB018217
Service Bulletin/Repair Instructions
TSB: SUPERSESSION NOTICE The information contained in this bulletin supersedes SB No. T-SB-0101-11. Applicability has been updated to include 2016 ? 2017 model year vehicles. Service Bulletin No. T-SB-0101-11 is Obsolete and any printed versions should be discarded. Be sure to review the entire content of this bulletin before proceeding. When servicing interior electrical switches and components, please note the precautions in this bulletin to avoid damaging electrical components and switches. Many lubricants, cleaners, and automotive chemicals contain silicone or other compounds that may contaminate electrical contacts, and therefore increase electrical resistance and decrease switch performance. The use of any cleaners or fluids may increase the risk of further damage to electrical components.
T-SB-0012-13 Rev
Service Bulletin/Repair Instructions
TSB: OBSOLETE NOTICE: September 14, 2016: This bulletin is now obsolete. Please see T-SB-0134-16.
T-SB-0142-13 Rev
Service Bulletin/Repair Instructions
TSB: REVISION NOTICE November 10, 2016 Rev2: ? Applicability has been updated to include 2016 ? 2017 model year Toyota vehicles. ? Parts Information section has been updated. Some 2004 ? 2017 model year Toyota vehicles may exhibit odors naturally occurring from the HVAC system and/or related environmental factors. Although there is no way to eliminate these odors, follow the General Procedure in this bulletin to minimize the odors experienced.
T-SB-0134-16
Service Bulletin/Repair Instructions
TSB: Supersession Notice. Flash reprogramming allows the ECU software to be updated without replacing the ECU. Flash calibration updates for specific vehicle models/ECUs are released as field-fix procedures described in individual Service Bulletins. This bulletin details the Techstream ECU flash reprogramming process and outlines use of the Technical Information System (TIS) and the Calibration Update Wizard (CUW). Flash calibration updates can only be applied to the vehicle/ECU combination for which they are intended. ECUs have internal security that will not allow them to be programmed with another ECU?s information.
T-TT-0414-16
Service Bulletin/Repair Instructions
TT: Some customers may encounter Bluetooth® connectivity concerns such as: *Difficulty to pair the phone. *Intermittent Bluetooth® failure to connect to the vehicle when first turning on the vehicle. *Various Bluetooth® Audio functions are no longer functioning with customer's phone such as ability to change the track using the steering wheel controls.
T-SB-0045-14 REV
Service Bulletin/Repair Instructions
TSB: REVISION NOTICE - AUGUST 2, 2016 REV1 - APPLICABILITY HAS BEEN UPDATED TO INCLUDE 2015 - 2016 MODEL YEAR SIENNA VEHICLES. ANY PREVIOUS PRINTED VERSIONS OF THIS BULLETIN SHOULD BE DISCARDED. SOME 2011 2016 MODEL YEAR SIENNA VEHICLES MAY EXHIBIT A VIBRATION/PULSATION FROM THE FRONT BRAKES THAT CAN BE FELT IN THE BRAKE PEDAL WHILE LIGHTLY APPLYING THE BRAKE PEDAL. NEW FRONT BRAKE PADS AND A NEW FIELD FIX REPAIR PROCEDURE HAVE BEEN DEVELOPED TO IMPROVE THIS CONDITION.
Safety Recall an
Service Bulletin/Repair Instructions
Update on Technician Certification Requirements.
T-SB-0044-16
Service Bulletin/Repair Instructions
TSB: On some vehicles, when Rapgard? is removed, the paint may have a stained appearance. These stains appear to be under the clear coat (repainting this area is not necessary). The stain patterns are usually under wrinkles in the Rapgard?. These wrinkles sometimes trap water and cause the paint to stain from the trapped moisture, especially on horizontal surfaces, such as the hood, roof, and trunk. Stains can be removed by heating the stained surface to remove the trapped moisture.
T-TT-0392-16 Rev
Service Bulletin/Repair Instructions
TT: Some customers may experience Bluetooth connection issues after updating the Android Operating System to 5.x.x (Lollipop) or later.
T-TT-0392-16
Service Bulletin/Repair Instructions
TT: Some customers may experience Bluetooth connection issues after updating the Android Operating System to 5.x.x (Lollipop) or later.
T-SB-0036-13 Rev
Service Bulletin/Repair Instructions
TSB: This bulletin includes basic procedures for inspecting and adjusting World Standard (WS) Automatic Transmission Fluid (ATF) level at normal vehicle operating temperature. Note: The following adjustment procedures are for U660E/F and U760E/F transmissions.
T-TT-0268-13 REV
Service Bulletin/Repair Instructions
TT: SOME CUSTOMERS MAY ENCOUNTER BLUETOOTH CONNECTIVITY CONCERNS SUCH AS: DIFFICULTY PAIRING THE PHONE. INTERMITTENT BLUETOOTH FAILURE TO CONNECT WHEN FIRST TURNING ON THE VEHICLE. VARIOUS BLUETOOTH AUDIO FUNCTIONS ARE NO LONGER FUNCTIONING WITH THE CUSTOMERS PHONE, SUCH AS THE ABILITY TO CHANGE THE TRACK USING THE STEERING WHEEL CONTROLS. THESE CONCERNS CAN BE CAUSED BY CHANGES MADE ON THE CUSTOMERS PHONE. MAKE SURE TO INQUIRE WITH THE CUSTOMER IF THE CONNECTIVITY CONCERNS OCCURRED AFTER RECEIVING AN OPERATING SYSTEM UPDATE ON THEIR PHONE OR IF THEY HAVE RESTORED THEIR PHONE DATA/SETTINGS RECENTLY.
T-TT-0374-15
Service Bulletin/Repair Instructions
TT: Since MY 2011, several different update or upgrade USB SSTs have been issued for Toyota audio and navigation systems. Refer to the chart below for a comprehensive list of all current and previously issued USB SSTs and their applicability.
T-TT-0374-15 REV
Service Bulletin/Repair Instructions
TT: SINCE MY 2011, SEVERAL DIFFERENT UPDATE OR UPGRADE USB SSTS HAVE BEEN ISSUED FOR TOYOTA AUDIO AND NAVIGATION SYSTEMS. REFER TO THE CHART BELOW FOR A COMPREHENSIVE LIST OF ALL CURRENT AND PREVIOUSLY ISSUED USB SSTS AND THEIR APPLICABILITY.
TTT-0268-13 Rev3
Service Bulletin/Repair Instructions
TT: Some customers may encounter Bluetooth connectivity concerns such as: ? Difficulty pairing the phone. ? Intermittent Bluetooth failure to connect when first turning on the vehicle. ? Various Bluetooth Audio functions are no longer functioning with the customer?s phone, such as the ability to change the track using the steering wheel controls. These concerns can be caused by changes made on the customer?s phone. Make sure to inquire with the customer if the connectivity concerns occurred after receiving an operating system update on their phone or if they have restored their phone data/settings recently.
T-TT-0381-16
Service Bulletin/Repair Instructions
Tech Tip: Some customers may experience difficulty programming HomeLink.
T-TT-0356-15 REV
Service Bulletin/Repair Instructions
TT: SLIDING DOOR WILL NOT LATCH IN THE CLOSED POSITION DUE TO EITHER FRONT AND/OR REAR LOCK MALFUNCTIONING. PLEASE SEE LINK REFERENCES OF VIDEO FOR EXAMPLE CONDITION AND DIAGNOSIS INSTRUCTION.
T-TT-0356-15 Rev
Service Bulletin/Repair Instructions
TT: Sliding Door will not latch in the closed position due to either front and/or rear lock malfunctioning. Please see link references of video for example condition and diagnosis instruction.
T-SB-0118-15
Service Bulletin/Repair Instructions
TSB: Some 2011 ? 2015 model year Sienna vehicles may exhibit a condition where the driver side 2nd row seat with the tip-up style lower seat cushion has excessive up and down movement. While some seat movement is a normal characteristic of the design, this bulletin will help identify excessive movement and provide steps to address this condition.
T-SB-0180-12 REV
Service Bulletin/Repair Instructions
TSB: DECEMBER 2, 2015: THIS BULLETIN IS NOW OBSOLETE. PLEASE SEE T-SB-0118-15.
T-SB-0180-12 Rev
Service Bulletin/Repair Instructions
TSB: December 2, 2015: This bulletin is now obsolete. Please see T-SB-0118-15.
T-TT-0234-13 REV
Service Bulletin/Repair Instructions
TT: SINCE MY 2011, SEVERAL DIFFERENT UPDATE OR UPGRADE USB SSTS HAVE BEEN ISSUED FOR TOYOTA AUDIO AND NAVIGATION SYSTEMS. REFER TO THE CHART BELOW FOR A COMPREHENSIVE LIST OF ALL CURRENT AND PREVIOUSLY ISSUED USB SSTS AND THEIR APPLICABILITY.
TTT-0234-13 Rev6
Service Bulletin/Repair Instructions
TT: Since MY 2011, several different update or upgrade USB SSTs have been issued for Toyota audio and navigation systems. Refer to the chart below for a comprehensive list of all current and previously issued USB SSTs and their applicability.
T-TT-0362-15
Service Bulletin/Repair Instructions
TT: The vehicle may be difficult to start or have an abnormally low or rough idle after the battery has been disconnected or power to the Engine ECM has been interrupted.
T-TT-0360-15
Service Bulletin/Repair Instructions
TT: Customers may experience connectivity issues when the following conditions are met: The customer's iPhone is operating on iOS9 firmware. The customer's iPhone is connected to the vehicle via Bluetooth. The customer may complain of the following issues: When receiving two incoming calls simultaneously, both calls are ended automatically. iTunes Radio app does not play via Bluetooth audio. Podcast and Audiobook media playback is inoperative via Bluetooth audio.
T-TT-0356-15
Service Bulletin/Repair Instructions
TT: Sliding Door will not latch manually in the closed position due to either the front and or/rear lock malfunctioning. Please see link references of video for example condition.
T-TT-0086-11
Service Bulletin/Repair Instructions
TechTip: Condition - The vehicle may be difficult to start or have an abnormally low or rough idle after the battery has been disconnected or power to the Engine ECM has been interrupted.
T-SB-0043-14 Rev
Service Bulletin/Repair Instructions
TSB: The Immobilizer and Smart Key Reset is a feature that allows the registration of new keys when all master keys are lost. Once the system is reset, all previously registered keys will be erased. Follow the procedures in this bulletin to reset a vehicle Immobilizer or Smart Key system. NOTE: There are new security provisions required to obtain a Reset Pass-Code. It is critical that the instructions for this new process are reviewed BEFORE attempting to get a Pass-Code in the new system.
T-TT-0234-13 Rev
Service Bulletin/Repair Instructions
TT: Since MY 2011, several different update or upgrade USB SSTs have been issued for Toyota audio and navigation systems. Refer to the chart below for a comprehensive list of all current and previously issued USB SSTs and their applicability.
T-SB-0083-13 Rev
Service Bulletin/Repair Instructions
TSB: The procedure in this bulletin is a general guideline on how to properly diagnose the air conditioning system after a component failure. Refer to the applicable Repair Manual for vehicle specific repair procedures and parts.
T-TT-0293-14 Rev
Service Bulletin/Repair Instructions
TT: Safety Connect is a vehicle option which requires a subscription fee for the system to be active. The first year of service is provided in the vehicle purchase price. Once the subscription has lapsed the DCM will be in an inactive state. In some instances, a DCM may need to be replaced even though the customer is not using the service.
T-TT-0337-15
Service Bulletin/Repair Instructions
TT: When updating either the navigation or radio firmware, verify the vehicle applicability BEFORE beginning the update.
T-SB-0101-11 Rev
Service Bulletin/Repair Instructions
TSB: When servicing interior electrical switches and components, please note the precautions in this bulletin to avoid damaging electrical components and switches. Many lubricants, cleaners, and automotive chemicals contain silicone or other compounds that may contaminate electrical contacts, and therefore increase electrical resistance and decrease switch performance. The use of any cleaners or fluids may increase the risk of further damage to electrical components.
T-TT-0262-13 Rev
Service Bulletin/Repair Instructions
TT: Starting with 2010 Model Year, Toyota began a gradual transition to the use of synthetic 0w-20 viscosity engine oil. There are multiple benefits of this oil. Due to the them improved performance and durability of 0w-20 synthetic oil, Toyota has extended the oil change intervals to 10,000 miles for most vehicles that require this oil.
TTT-0337-15 Rev1
Service Bulletin/Repair Instructions
TT: When updating either the navigation or radio firmware, verify the vehicle applicability BEFORE beginning the update.
T-SB-0040-08
Service Bulletin/Repair Instructions
TSB: On some vehicles, when Rapgard is removed, the paint may have a stained appearance. These stains appear to be under the clear coat (repainting this area is not necessary). The stain patterns are usually under wrinkles in the Rapgard. These wrinkles sometimes trap water and cause the paint to stain from the trapped moisture, especially on horizontal surfaces, such as the hood, roof, and trunk. Stains can be removed by heating the stained surface to remove the trapped moisture.
T-SB-0012-13 REV
Service Bulletin/Repair Instructions
TSB: FLASH REPROGRAMMING ALLOWS THE ECU SOFTWARE TO BE UPDATED WITHOUT REPLACING THE ECU. FLASH CALIBRATION UPDATES FOR SPECIFIC VEHICLE MODELS/ECUS ARE RELEASED AS FIELD-FIX PROCEDURES DESCRIBED IN INDIVIDUAL SERVICE BULLETINS. THIS BULLETIN DETAILS THE TECHSTREAM ECU FLASH REPROGRAMMING PROCESS AND OUTLINES USE OF THE TECHNICAL INFORMATION SYSTEM (TIS) AND THE CALIBRATION UPDATE WIZARD (CUW). FLASH CALIBRATION UPDATES CAN ONLY BE APPLIED TO THE VEHICLE/ECU COMBINATION FOR WHICH THEY ARE INTENDED. ECUS HAVE INTERNAL SECURITY THAT WILL NOT ALLOW THEM TO BE PROGRAMMED WITH ANOTHER ECUS INFORMATION.
TSB-0012-13 Rev2
Service Bulletin/Repair Instructions
TSB: Flash reprogramming allows the ECU software to be updated without replacing the ECU. Flash calibration updates for specific vehicle models/ECUs are released as field-fix procedures described in individual Service Bulletins. This bulletin details the Techstream ECU flash reprogramming process and outlines use of the Technical Information System (TIS) and the Calibration Update Wizard (CUW). Flash calibration updates can only be applied to the vehicle/ECU combination for which they are intended. ECUs have internal security that will not allow them to be programmed with another ECU?s information.
T-TT-307-14 Rev1
Service Bulletin/Repair Instructions
TT: Customers complain of various Bluetooth connectivity concerns after upgrading to iOS 8.0 and later. Conditions typically experienced include inability to pair the iPhone to the system, poor sound quality during phone calls placed through the audio/navigation system, and the inability to place a hands free phone call using the audio/navigation system.
T-SB-0152-14
Service Bulletin/Repair Instructions
TSB: Some 2011 ? 2013 model year Sienna vehicles may exhibit a condition where the outside seat shield is loose and separating, or has an excessive gap to the seat cushion or forward facing seat shield. The condition may occur on either the driver or passenger front power equipped seats. Follow the Repair Procedure in this bulletin to address this condition.
T-SB-0147-14
Service Bulletin/Repair Instructions
TSB: Some 2011 - 2014 model year Sienna vehicles may exhibit a condition where a rattle or squeak type noise is heard from the rear of the vehicle while driving over rough road surfaces when the seats are empty in the upright latched position. If the 3rd row seats are stowed, the noise is no longer present.
T-SB-0006-11 Rev
Service Bulletin/Repair Instructions
TSB: World Standard (WS) Automatic Transmission Fluid (ATF) was introduced to reduce maintenance costs and increase the mileage between scheduled maintenance checks. Here are some important tips when working with ATF-WS in Toyota vehicles requiring it's use.
T-SB-0014-11 Rev
Service Bulletin/Repair Instructions
TSB: The purpose of this service bulletin is to provide information regarding the installation of the correct torque converter bolts during automatic transmission/transaxle assembly replacement. Incorrect torque converter bolts or missing washers can cause damage to the torque converter assembly.
T-SB-0260-08 Rev
Service Bulletin/Repair Instructions
TSB: The purpose of this bulletin is to assist in the identification and location of serial numbers on 2006 -2014 model year remanufactured automatic transmissions.
T-TT-0307-14
Service Bulletin/Repair Instructions
Tech Tip: Customer complains of carious Bluetooth connectivity concerns after upgrading to iOS 8.0 and later. Conditions typically experienced include inability to pair the iPhone to the system, poor sound quality during phone calls placed through the audio/navigation system, and the inability to place a hands free phone call using the audio/navigation system.
T-SB-0381-09 Rev
Service Bulletin/Repair Instructions
TSB: The only acceptable towing method for vehicles equipped with an Active Torque Control 4WD system is to have all four wheels off the ground. Flat towing or towing where only the front or rear wheels are supported may damage the all-wheel drive system.
T-SB-0134-14
Service Bulletin/Repair Instructions
TSB: The purpose of this bulletin is to provide precautions to follow when installing an automatic transmission/transaxle assembly to avoid MIL "ON" shifting issues and/or transmission damage. Use the information in this bulletin when installing an automatic transmission/transaxle assembly.
T-SB-0200-08 Rev
Service Bulletin/Repair Instructions
TSB: The purpose of this bulletin is to assist in the identification and location of serial numbers on 2006 - 2014 model year automatic transmissions.
T-TT-0234-13
Service Bulletin/Repair Instructions
Tech Tip: Since MY 2011, several different update or upgrade USB SSTs have been issued for Toyota audio and navigation systems.
T-TT-0246-13 Rev
Service Bulletin/Repair Instructions
Tech Tip: Tips for writing a DPR (Dealer Product Report) on manufacturing issues for windows and windshields.
T-SB-0045-14
Service Bulletin/Repair Instructions
TSB: Some 2011 ? 2014 model year Sienna vehicles may exhibit a vibration/pulsation from the front brakes that can be felt in the brake pedal while lightly applying the brake pedal. New front brake pads and a new field fix repair procedure have been developed to improve this condition.
E0N_LSC_Dealer L
Service Bulletin/Repair Instructions
Dealer Letter: The Pre-Collision System (PCS) uses a radar sensor to determine the possibility of a frontal collision. FCC regulations require the radar sensor to be temporarily inactive while the vehicle is stopped. Due to a program error in the Driving Support ECU, if the radar sensor is inactive for 10 seconds or more, the PCS may not reactivate on certain 2011-2014 Model Year Sienna vehicles equipped with PCS.
E0N_LSC_Region L
Service Bulletin/Repair Instructions
Region Letter: The Pre-Collision System (PCS) uses a radar sensor to determine the possibility of a frontal collision. FCC regulations require the radar sensor to be temporarily inactive while the vehicle is stopped. Due to a program error in the Driving Support ECU, if the radar sensor is inactive for 10 seconds or more, the PCS may not reactivate Pre-Collision Braking on certain 2011-2014 Model Year Sienna vehicles equipped with PCS.
PSD-TC-14-014
Service Bulletin/Repair Instructions
TOYOTA: SEE DOCUMENT SEARCH BUTTON FOR OWNER LETTER. A PROGRAM ERROR, IN DRIVING SUPPORT ECU, HAS RADAR SENSOR PRE-COLLISION SYSTEM (PCS) INACTIVE 10 SECONDS OR MORE, WHILE STOPPED, WILL FAIL TO REACTIVATE PRE-COLLISION BRAKING. MODEL 2011-2014 SIENNA. *PE
T-TT-0293-14
Service Bulletin/Repair Instructions
Tech Tip: Safety Connect is a vehicle option which requires a subscription fee for the system to be active. The first year of service is provided in the vehicle purchase price. Once the subscription has lapsed the DCM will be in an inactive state. In some instances, a DCM may need to be replaced even though the customer is not using the service.
T-TT-0010-10 Rev
Service Bulletin/Repair Instructions
Tech Tip: Low battery voltage can contribute to a MIL "ON" condition for P0335 (Crankshaft Position Sensor Circuit) and/or P0340 (Camshaft Position Sensor Circuit) due to inconsistent rotational speed of the engine's crankshaft.
T-SB-0033-14
Service Bulletin/Repair Instructions
Some vehicles in particular geographic areas may exhibit a condition where the HVAC Evaporator Drain Hose has become obstructed with an insect nest. An insect repellent drain hose tip (ARINIX® Tip) is now available to help minimize future occurrences of this environmental condition. For some models, a new drain hose is required to properly fit the ARINIX® Tip. Follow the procedures in this bulletin for proper handling and installation of this optional service part.
T-TT-0223-13
Service Bulletin/Repair Instructions
The vehicle will not start or ready0on and the steering wheel lock is engaged so that the steering wheel may only be turned very little from side-to-side. If the operator attempts to ready-on or start the vehicle while there is tension on the steering lock actuator, it will not be able to fully disengage when the "ENGINE START STOP" or "POWER" switch is depressed. This condition will cause the "ENGINE START STOP" or "POWER" switch's LED to flash green and the vehicle will fail to ready-on or start.
T-TT-0288-14
Service Bulletin/Repair Instructions
Prior to installing remanufactured U660 and U760 transaxles, it is necessary to remove the lower oil cooler tube union from the original transaxle case and install it into the reman unit. A NEW O-ring and printed installation instructions are supplied in separate bag with the reman unit. An instruction tag is also affixed to the unit.
T-SB-0192-11 Rev
Service Bulletin/Repair Instructions
Some 2011 ? 2014 model year Sienna vehicles with the factory mobility seat option may exhibit a condition where the seat slide function becomes inoperative due to plastic spacer interference in the lift mechanism. The seat lift mechanism has been improved to address this condition.
T-TT-0268-13
Service Bulletin/Repair Instructions
Customer complains of Bluetooth connectivity concerns such as: Difficulty to pair phone, Intermittent Bluetooth failure to connect to the vehicle when first turning on the vehicle. These concerns can be caused by changes made on the customer's phone. Make sure to inquire with the customer if the connectivity concerns occurred after receiving an operating system update on their phone or they have restored their phone data/settings recently.
T-TT-0262-13
Service Bulletin/Repair Instructions
Starting with the 2010 Model Year, Toyota began a gradual transition to the use of synthetic 0w-20 viscosity engine oil. There are multiple benefits of this oil. Due to the improved performance and durability of 0w-20 synthetic oil, Toyota has extended the oil change intervals to 10,000 miles for most vehicle that require this oil.
T-SB-0187-12 Rev
Service Bulletin/Repair Instructions
Toyota vehicles are equipped with either conventional or run-flat tires. Sometimes punctures may occur as a result of contact with road debris or other hazards. If a puncture occurs, it may be possible to repair the tire and return it to service. With a conventional tire it is not possible to drive for an extended amount of time with the tire at low pressures as damage to the tire may occur. With run-flat tires, due to reinforced sidewalls, it is possible to drive for up to 100 miles (160 km) at speeds less than 55 mph (90 km/h) with little or no damage to the tire.
T-TT-0213-13
Service Bulletin/Repair Instructions
Toyota vehicles are equipped with Supplemental Restraint Systems (SRS), including various airbags and in some models, seat belt pre-tensioners, to help reduce the risk of injury in a collision. If a customer expresses any concerns that the SRS airbags or pre-tensioner devices did not perform as expected (including an unintended deployment event), please follow the steps in the recommendations section below.
T-TT-0278-13
Service Bulletin/Repair Instructions
The customer is unable to delete their call history or contacts from the Denso GEN7 Navigation System. The ?delete? soft button on the multi-information display is greyed out and not selectable.
T-SB-0185-13
Service Bulletin/Repair Instructions
The following procedures are recommended during routine maintenance or in the event of a customer concern for wiper performance.
TS-BO030-01 Obso
Service Bulletin/Repair Instructions
This bulletin is now obsolete. Please see T-SB-0185-13.
T-SB-0122-11 Rev
Service Bulletin/Repair Instructions
Beginning in 1998, Toyota introduced side airbags as optional equipment. Toyota does NOT recommend replacement of original seat covers with non-Toyota leather or other seat cover materials on vehicles due to the following: Seat covers NOT recommended by Toyota may affect side airbag performance, in general or in part, during an accident. Modifications that negatively affect side airbag performance can result in severe occupant injuries. Seat covers are an integral part of this safety system. Replacing fabric seat covers with non-Toyota leather or other seat cover materials may compromise the effectiveness of this safety system. The design of the seat is complex, integrating safety and strength with comfort and luxury. Toyota strongly discourages modifying original equipment seats that have optional side airbags. Additionally, Toyota strongly advises against the installation or use of aftermarket seat covers, which could impair the performance of the side airbags in the event of an accident.
T-SB-0041-13 Rev
Service Bulletin/Repair Instructions
Immediately following a cold soak startup, some 2009 ? 2013 model year vehicles equipped with 1AR-FE or 2AR-FE engines may exhibit a brief knock/rattle noise from the engine compartment for approximately one second. Follow the repair procedure below to address this condition.
T-TT-0269-13
Service Bulletin/Repair Instructions
The appearance of spots in tempered glass (when viewed at certain angles) is the result of the heat treating and quick quenching process during manufacturing.
T-SB-0152-13
Service Bulletin/Repair Instructions
Some vehicles may exhibit a condition where there is a lack of cooling from the A/C system. An A/C Line Retainer (Piping Clamp) may have become unlatched and caused a refrigerant leak. Follow the procedure in this bulletin to address this condition.
T-TT-0051-10
Service Bulletin/Repair Instructions
If a customer states there is an unpleasant odor in the vehicle from the HVAC system, there are various factors that may be involved.
T-TT-0260-13
Service Bulletin/Repair Instructions
Customer?s experiencing this condition can use a 3rd party podcast application on their iPhone (such as Pocket Casts or Instances) instead of the native Apple Podcast application.
T-SB-0071-11 Rev
Service Bulletin/Repair Instructions
The purpose of this service bulletin is to provide precautions to follow when installing an automatic transmission/transaxle assembly to avoid MIL ?ON,? shifting issues, and/or transmission damage. Use the information in this bulletin when installing an automatic transmission/transaxle assembly
T-TT-0257-13
Service Bulletin/Repair Instructions
iTunes Radio is a new feature for iPhone 4, 4S, 5, 5S, and 5C running iOS 7 or later. This feature does work with the in-vehicle audio system either via Bluetooth or by USB cable. Details on how to access this feature are described below.
T-TT-0256-13
Service Bulletin/Repair Instructions
Customers using iPhone 4, 4S, 5, 5S, or 5C running iOS 7.0 or later now have the ability to make Facetime Audio calls (no video). When a customer is paired by Bluetooth Hands Free and they make a Facetime Audio call the vehicle radio will treat it as a typical Bluetooth phone call. Because Facetime works differently than a typical phone call, the in-vehicle experience may not meet the customer?s expectations.
T-TT-0256-13A
Service Bulletin/Repair Instructions
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
T-TT-0199-12
Service Bulletin/Repair Instructions
Some users may experience no sound from the Pandora or iHeartRadio Entune Applications after attaching the iPhone USB cable to the multimedia system. This can also occur if the user chooses the iPod selection on the multimedia system and then attempts to return to Pandora or iHeartRadio Entune Applications. This condition occurs with iPhones running iOS 6.0 and later
T-TT-0199-12 Rev
Service Bulletin/Repair Instructions
Some users may experience no sound from the Pandora or iHeartRadio Entune Applications after attaching the iPhone USB cable to the multimedia system. This can also occur if the user chooses the iPod selection on the multimedia system and then attempts to return to Pandora or iHeartRadio Entune Applications. This condition occurs with iPhones running iOS 6.0 and later.
T-TT-0051-10 Rev
Service Bulletin/Repair Instructions
If a customer states there is an unpleasant odor in the vehicle from the HVAC system, there are various factors that may be involved.
T-TT-0250-13
Service Bulletin/Repair Instructions
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
T-TT-0250-13 Rev
Service Bulletin/Repair Instructions
To receive satellite radio functions after the initial trial period has expired, the customer must enter into a contract with XM Satellite Radio Inc. After entering into a contract, registration of an 8-digit XM Radio ID is required. This 8-digit XM Radio ID is found by turning to channel ?0? of the satellite radio.
T-SB-0142-13
Service Bulletin/Repair Instructions
Some 2004 ? 2014 model year Toyota vehicles may exhibit odors naturally occurring from the HVAC system and/or related environmental factors. Although there is no way to eliminate these odors, follow the General Procedure in this bulletin to minimize the odors experienced.
T-SB-0141-13
Service Bulletin/Repair Instructions
A new Special Service Tool (SST 09709-00002) has been introduced to aid in the inspection procedure for certain vehicles equipped with a floor pedal-type parking brake system. This bulletin references the correct method for installing the Brake Pedal Force Gauge. Refer to the appropriate Repair Manual for parking brake pedal travel inspection and adjustment specification.
T-TT-0251-13
Service Bulletin/Repair Instructions
Some customers may experience A/C is inoperative with the DTC B1479 present. This can be caused by debris stuck in the flow control valve.
T-SB-0060-12 Rev
Service Bulletin/Repair Instructions
An Initialization Process is required to activate the Entune? suite of Apps & Data Services on Premium HDD Navigation with Entune? and Display Navigation with Entune? head units before they are used for the first time on new vehicles. The Initialization Process may also need to be performed under other circumstances such as following a head unit replacement or after the customer?s personal settings are erased. The Initialization process requires between 3 and 15 minutes to complete, depending on the type of head unit, file size, cellular connection speed, and other factors.
T-TT-0005-10
Service Bulletin/Repair Instructions
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
T-TT-0246-13
Service Bulletin/Repair Instructions
Tips for writing a DPR (Dealer Product Report) on manufacturing issues for windows and windshields.
T-SB-0083-13
Service Bulletin/Repair Instructions
The procedure in this bulletin is a general guideline on how to properly diagnose the air conditioning system after a component failure. Refer to the applicable Repair Manual for vehicle specific repair procedures and parts.
T-TT-0124-11
Service Bulletin/Repair Instructions
Please refer to the following recommendations for the best practices for vehicle tire rotations.
T-TT-0239-13
Service Bulletin/Repair Instructions
On some Highlander, Sienna, and Sequoia vehicles, a plastic clamp connecting the rear A/C lines may become loose. This may allow separation of the A/C lines and a loss of refrigerant.
T-PG006-00 Obsol
Service Bulletin/Repair Instructions
This bulletin is now obsolete. Please see T-SB-0054-13.
T-SB-0054-13
Service Bulletin/Repair Instructions
California (CA), Federal (FED), and 50 State Certified emission control underhood labels (emission labels) may be obtained through your dealership?s Parts Department utilizing standard replacement parts ordering procedures. Follow the guidelines outlined in this bulletin to ensure proper label application.
T-SB-0053-13
Service Bulletin/Repair Instructions
After initial start-up in cold weather conditions, the front windshield defroster pattern may not meet customer expectations. An updated A/C amplifier is available that improves the front windshield defroster pattern.
T-SB-0035-13 Rev
Service Bulletin/Repair Instructions
Some 2012 model year Corolla, Prius, Prius V, Sienna, and Venza vehicles may set SRS Diagnostic Trouble Codes (DTCs) that are not listed in the Repair Manual. Refer to the chart in this bulletin to diagnose these DTCs.
T-SB-0141-10 Rev
Service Bulletin/Repair Instructions
If a creak, tick, or rattle noise is heard at the top or bottom of the windshield, or at the top of the rear glass, the source of the noise may be the two stoppers bonded to the top of the windshield/rear glass, or the windshield retainers bonded to the lower edge of the windshield. This bulletin provides the recommended repair procedure to eliminate these types of noises from the windshield/rear glass area.
T-SB-0052-13
Service Bulletin/Repair Instructions
Some 2011 ? 2012 model year Sienna vehicles may exhibit a condition where the front door glass run on either the RH or LH side becomes loose or does not stay in place. Vehicles may also exhibit a condition where the front door glass run is pulled off the track and may come down while the window is operated. Use the following repair procedure to address this condition.
T-SB-0041-13
Service Bulletin/Repair Instructions
Immediately following a cold soak startup, some 2009 ? 2013 model year vehicles equipped with 1AR-FE or 2AR-FE engines may exhibit a brief knock/rattle noise from the engine compartment for approximately one second. Follow the repair procedure below to address this condition.
TSB-004-13-A
Service Bulletin/Repair Instructions
TOYOTA: THERE IS A KNOCKING OR RATTLING NOISE COMING FROM ENGINE COMPARTMENT, FOR A SHORT PERIOD OF TIME, AFTER A COLD SOAK STARTUP. MODEL 2010-2012 CAMRY, 2009-2013 HIGHLANDER, VENZA, 2009-2012 RAV4, 2011-2013 SIENNA. *PE
TSB-0041-13
Service Bulletin/Repair Instructions
TOYOTA: ON CERTAIN VEHICLES, A KNOCK OR RATTLE NOISE, COMING FROM ENGINE COMPARTMENT, IS HEARD DURING A COLD SOAK STARTUP, AND THE CONDITION LASTS APPROXIMATELY ONE SECOND. MODEL YEARS 2009-2012 CAMRY, HIGHLANDER, SIENNA, VENZA, RAV4. *PE
T-TT-0226-13
Service Bulletin/Repair Instructions
The customer is having difficulty changing the multi-display screen from Day Mode. If the multi-display screen is set to Day Mode when the headlights are on, the setting we be memorized when the engine is turned off.
T-SB-0035-13
Service Bulletin/Repair Instructions
Some 2012 model year Corolla, Prius, Prius V, Sienna, and Venza vehicles may set SRS Diagnostic Trouble Codes (DTCs) that are not listed in the Repair Manual. Refer to the chart in this bulletin to diagnose these DTCs.
T-SB-0391-08 Rev
Service Bulletin/Repair Instructions
This bulletin contains general vehicle pulling diagnosis and repair procedures along with specific information to help correct pulling complaints.
T-SB-0033-13
Service Bulletin/Repair Instructions
Some customers may inquire about the frequency and power output of the Smart Key/Smart Entry systems used on various models. The Smart Key/Smart Entry systems conform to all applicable FCC rules. This bulletin details the applicable specifications for these systems.
SST Requirements
Service Bulletin/Repair Instructions
SSTs are key elements to provide your customers with swift and accurate repairs resulting in superior customer satisfaction.
SET Airbag Senso
Service Bulletin/Repair Instructions
This communication pertains to a current safety recall being conducted by the Southeast Toyota Distributors LLC (SET). TMS is sending this communication for informational purposes in the event you are contacted by a customer covered by this recall.
T-SB-0012-13
Service Bulletin/Repair Instructions
Flash reprogramming allows the ECU software to be updated without replacing the ECU. Flash calibration updates for specific vehicle models/ECUs are released as field-fix procedures described in individual Service Bulletins. This bulletin details the Techstream ECU flash reprogramming process and outlines use of the TIS and the CUW.
T-SB-0064-10 Rev
Service Bulletin/Repair Instructions
This bulletin is now obsolete. Please see T-SB-0012-13.
TTT-0213-13
Service Bulletin/Repair Instructions
TOYOTA: IN A COLLISION, TO HELP REDUCE INJURIES, WITH SEAT BELT PRE=TENSIONERS AND SUPPLEMENTAL RESTRAINT SYSTEMS (SRS), ITS POSSIBLE THAT THE DEVICES MAY OR MAY NOT PERFORM AS EXPECTED WITH UNINTENDED DEPLOYMENT. MODEL YEARS 1990-2013. MODELS VARIOUS MODELS. *PE
T-TT-0005-10 Rev
Service Bulletin/Repair Instructions
Starting with the 2010 MY, Toyota began a gradual transition to the use of synthetic 0w-20 viscosity engine oil.
T-TT-0203-12 Rev
Service Bulletin/Repair Instructions
Some Phone iOS 5 customers with Denso Premium HDD Navigation (AVN) or Display Navigation w/ Entune (DNE) head units may experience an iPod Authorization error when they plug their iPhone into the USB port.
T-TT-0204-12 Rev
Service Bulletin/Repair Instructions
Some Phone iOS 5 customers with Denso Premium HDD Navigation (AVN) or Display Navigation w/ Entune (DNE) head units may experience an error message when they attempt to use the Entune application.
T-TT-0204-12
Service Bulletin/Repair Instructions
Some Phone iOS 5 customers with Denso Premium HDD Navigation (AVN) or Display Navigation w/ Entune (DNE) head units may experience an error message when they attempt to use the Entune application.
T-TT-0205-12
Service Bulletin/Repair Instructions
Customers who purchase new or replacement iPhones running iOS 6 may find that Toyota a Entune application will not launch on the iPhone. The issue can occur when the customer restores/transfers their apps, contacts, etc.
T-TT-0203-12
Service Bulletin/Repair Instructions
Some Phone iOS 5 customers with Denso Premium HDD Navigation (AVN) or Display Navigation w/ Entune (DNE) head units may experience an iPod Authorization error when they plug their iPhone into the USB port.
T-SB-0187-12
Service Bulletin/Repair Instructions
Toyota vehicles are equipped with either conventional or run-flat tires. Sometimes punctures may occur as a result of contact with road debris or other hazards. If a puncture occurs, it may be possible to repair the tire and return it to service. With a conventional tire it is not possible to drive for an extended amount of time with the tire at low pressures as damage to the tire may occur. With run-flat tires, due to reinforced sidewalls, it is possible to drive for up to 100 miles (160 km) at speeds less than 55 mph (90 km/h) with little or no damage to the tire.
T-SB-0180-12
Service Bulletin/Repair Instructions
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
TSB-0172-12
Service Bulletin/Repair Instructions
TOYOTA: AN INTERMITTENT EXHIBITION OF SRS LAMP ON WITH DIAGNOSTIC TROUBLE CODE (DTC) B1821 AND/OR B1826 CONDITION. IMPROVEMENT TO TERMINAL CRIMPING OF SIDE AIR BAG TO ADDRESS SITUATION. MODEL 2011-2012 SIENNA.
TSB-0087-12
Service Bulletin/Repair Instructions
TOYOTA: ACCELERATOR PEDAL SENSOR ASSEMBLY INFORMATION REGARDING THE INSPECTION, REMOVAL, AND INSTALLATION, IF LUBRICATION OR OIL, IS APPLIED. *PE
T-SB-0060-12
Service Bulletin/Repair Instructions
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
T-SB-0055-12
Service Bulletin/Repair Instructions
TOYOTA: CHARGING SYSTEM INOPERATIVE. SOME ENGINES MAY EXHIBIT INSUFFICIENT CHARGING PERFORMANCE FROM THE ALTERNATOR. AN UPDATED PULLEY ASSEMBLY IS AVAILABLE TO ADDRESS THIS CONDITION. *JS
T-SB-0192-11
Service Bulletin/Repair Instructions
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
TSB-0122-11
Service Bulletin/Repair Instructions
TOYOTA: INFORMATION PROVIDED FOR REPLACING THE SEAT COVERS FOR VEHICLES EQUIPPED WITH SIDE AIRBAGS. *PE
TSB-0025-11
Service Bulletin/Repair Instructions
TOYOTA: LONG-TERM STORAGE PROCEDURE FOR SOME 2012 MODELS. *RM
T-PG007-01
Service Bulletin/Repair Instructions
Replacement vin plates.
T-PG002-91
Service Bulletin/Repair Instructions
Product general information.