Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
T-SB-0055-24 Rev2
Service Bulletin/Repair Instructions
Some 2005 – 2026 Toyota vehicles that have undergone water intrusion may exhibit a condition in which a musty odor is present. Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this Service Bulletin is to provide general guidelines and procedures for odor remediation. This Service Bulletin provides a guide on how to prepare and treat the interior of the vehicle for odor remediation. Refer to the applicable model and model year Repair Manual and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines.
T-SB-0035-24 Rev2
Service Bulletin/Repair Instructions
Acid rain results from rainwater or other airborne moisture that become acidic due to industrial chemical impurities in the atmosphere. If these acidic compounds settle on an exposed vehicle, especially the horizontal areas such as the hood, roof, and decklid, significant damage to the painted surfaces can occur. Acid rain damage can typically be identified on vehicles by the presence of stains on the paint surface that resemble hard water spots. Unlike water spots however, acid rain damage cannot be removed by regular washing procedures. Also, because acid rain can etch and soften the paint, normal buffing or polishing repair procedures should not be attempted. This can cause further damage and result in visible depressions in the paint surface. The following are the three major categories of acid rain damage: •Minor damage: requires only buffing to repair. •Moderate damage: usually requires neutralizing, color sanding, and buffing. •Severe damage: extending beyond 1/2 mil of clearcoat on a pearl, metallic, or solid color, requires neutralization, sanding, and repainting. In cases where acid rain damage is minor, neutralization and buffing with a liquid-type paint finessing product may provide an adequate repair. Only specially formulated products outlined in this bulletin should be used for that purpose. Unfortunately, other than minor damage, there is no simple method of determining the actual extent (depth) of acid penetration other than color sanding a representative affected area until there is no visible etching or depressions, followed by measuring the amount of paint removed with either a magnetic or digital-type film thickness gauge. The procedures in this bulletin are intended for use by qualified body/paint technicians and should not be attempted by inexperienced personnel. It is the dealer’s responsibility to protect and maintain the quality of the vehicle’s paint finish after receipt at the dealership prior to the first sale. Perform frequent vehicle washing, as often as daily, during high heat and humidity periods to minimize the potential for paint damage due to acid rain exposure. This is especially important in geographical areas known for high frequency and concentration of acid rain and industrial fallout.
T-SB-0038-24 Rev2
Service Bulletin/Repair Instructions
To prevent brake rotor rust from forming during transportation and storage, wheel film will be used instead of a cardboard type of anti-rust cover. The purpose of the wheel film is to shield the disc brake rotor from weather elements and initial rust before the vehicle is delivered to the customer. Consequently, the film should remain on the wheel for as long as possible.
T-SB-0039-24 Rev2
Service Bulletin/Repair Instructions
The condition known as acid rain is caused by airborne chemicals or particles in the atmosphere, which mix with rainwater, nighttime dew, or high humidity to form acidic compounds. If these contaminants settle and remain on a painted vehicle surface, especially the horizonal areas of the hood, roof, and decklid, significant damage can occur. This damage is the result of actual etching of the paint and appears as pitting or water spots. As acid rain droplets on the vehicle surface evaporate, the concentration strength of the acid increases, causing deeper and more rapid damage. This evaporation and corrosive action also occur more rapidly on dark colored cars as direct sun heat increases. It is the dealer’s responsibility to protect and maintain the quality of the vehicle’s paint finish after receipt at the dealership prior to the first sale. In areas known for high frequency and/or concentration of acid rain, frequent vehicle washing during high heat or humidity periods will minimize the potential for paint damage caused by acid rain. It is further recommended that either reverse osmosis or deionized water be used to prevent water spotting.
T-SB-0061-23 Rev2
Service Bulletin/Repair Instructions
Toyota vehicles are currently protected with RapgardTM protective film designed to protect the horizontal painted surfaces. This material protects from acid rain, environmental fallout, and rail contamination. Follow the Removal Procedure in this bulletin to remove the RapgardTM protective film within 90 days from initial application.
T-SB-0062-23 Rev2
Service Bulletin/Repair Instructions
Vehicles may occasionally be subjected to contamination by airborne iron particles shed from railroad tracks, train wheels, exposure to heavy machinery facilities, grinding, welding, etc. This type of contamination can be identified by the presence of small, red or brown particles on the paint surface. These particles are often difficult to see on dark color paints but can be easily felt when brushing a hand across horizontal body surfaces such as the hood, roof, or deck lid. Follow the Repair Procedure in this bulletin to clean vehicles that may have been subjected to contamination by airborne iron particles such as rail dust during rail transportation or extended storage near industrial areas.
T-SB-0055-24 Rev1
Service Bulletin/Repair Instructions
Some 2005 – 2024 Toyota vehicles that have undergone water intrusion may exhibit a condition in which a musty odor is present. Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this Service Bulletin is to provide general guidelines and procedures for odor remediation. This Service Bulletin provides a guide on how to prepare and treat the interior of the vehicle for odor remediation. Refer to the applicable model and model year Repair Manual and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines. This Service Bulletin is to provide a general overview and direction for the odor remediation process.
T-SB-0035-24 Rev1
Service Bulletin/Repair Instructions
Acid rain results from rainwater or other airborne moisture that become acidic due to industrial chemical impurities in the atmosphere. If these acidic compounds settle on an exposed vehicle, especially the horizontal areas such as the hood, roof, and decklid, significant damage to the painted surfaces can occur. Acid rain damage can typically be identified on vehicles by the presence of stains on the paint surface that resemble hard water spots. Unlike water spots however, acid rain damage cannot be removed by regular washing procedures. Also, because acid rain can etch and soften the paint, normal buffing or polishing repair procedures should not be attempted. This can cause further damage and result in visible depressions in the paint surface. The following are the three major categories of acid rain damage: •Minor damage: requires only buffing to repair. •Moderate damage: usually requires neutralizing, color sanding, and buffing. •Severe damage: extending beyond 1/2 mil of clearcoat on a pearl, metallic, or solid color, requires neutralization, sanding, and repainting. In cases where acid rain damage is minor, neutralization and buffing with a liquid-type paint finessing product may provide an adequate repair. Only specially formulated products outlined in this bulletin should be used for that purpose. Unfortunately, other than minor damage, there is no simple method of determining the actual extent (depth) of acid penetration other than color sanding a representative affected area until there is no visible etching or depressions, followed by measuring the amount of paint removed with either a magnetic or digital-type film thickness gauge. The procedures in this bulletin are intended for use by qualified body/paint technicians and should not be attempted by inexperienced personnel. It is the dealer’s responsibility to protect and maintain the quality of the vehicle’s paint finish after receipt at the dealership prior to the first sale. Perform frequent vehicle washing, as often as daily, during high heat and humidity periods to minimize the potential for paint damage due to acid rain exposure. This is especially important in geographical areas known for high frequency and concentration of acid rain and industrial fallout.
T-SB-0038-24 Rev1
Service Bulletin/Repair Instructions
To prevent brake rotor rust from forming during transportation and storage, wheel film will be used instead of a cardboard type of anti-rust cover. The purpose of the wheel film is to shield the disc brake rotor from weather elements and initial rust before the vehicle is delivered to the customer. Consequently, the film should remain on the wheel for as long as possible.
T-SB-0039-24 Rev1
Service Bulletin/Repair Instructions
The condition known as acid rain is caused by airborne chemicals or particles in the atmosphere, which mix with rainwater, nighttime dew, or high humidity to form acidic compounds. If these contaminants settle and remain on a painted vehicle surface, especially the horizonal areas of the hood, roof, and decklid, significant damage can occur. This damage is the result of actual etching of the paint and appears as pitting or water spots. As acid rain droplets on the vehicle surface evaporate, the concentration strength of the acid increases, causing deeper and more rapid damage. This evaporation and corrosive action also occur more rapidly on dark colored cars as direct sun heat increases. It is the dealer’s responsibility to protect and maintain the quality of the vehicle’s paint finish after receipt at the dealership prior to the first sale. In areas known for high frequency and/or concentration of acid rain (see Figure 1), frequent vehicle washing during high heat or humidity periods will minimize the potential for paint damage caused by acid rain. It is further recommended that either reverse osmosis or deionized water be used to prevent water spotting.
T-SB-0055-24
Service Bulletin/Repair Instructions
Some 2005 – 2024 Toyota vehicles that have undergone water intrusion may exhibit a condition in which a musty odor is present. Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this Service Bulletin is to provide general guidelines and procedures for odor remediation. This Service Bulletin provides a guide on how to prepare and treat the interior of the vehicle for odor remediation. Refer to the applicable model and model year Repair Manual and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines.
T-SB-0061-23 Rev1
Service Bulletin/Repair Instructions
Toyota vehicles are currently protected with RapgardTM protective film designed to protect the horizontal painted surfaces. This material protects from acid rain, environmental fallout, and rail contamination.
T-SB-0062-23 Rev1
Service Bulletin/Repair Instructions
Vehicles may occasionally be subjected to contamination by airborne iron particles shed from railroad tracks, train wheels, exposure to heavy machinery facilities, grinding, welding, etc. This type of contamination can be identified by the presence of small, red or brown particles on the paint surface. These particles are often difficult to see on dark color paints but can be easily felt when brushing a hand across horizontal body surfaces such as the hood, roof, or deck lid.
T-SB-0035-24
Service Bulletin/Repair Instructions
Acid rain results from rainwater or other airborne moisture that become acidic due to industrial chemical impurities in the atmosphere. If these acidic compounds settle on an exposed vehicle, especially the horizontal areas such as the hood, roof, and decklid, significant damage to the painted surfaces can occur. Acid rain damage can typically be identified on vehicles by the presence of stains on the paint surface that resemble hard water spots. Unlike water spots however, acid rain damage cannot be removed by regular washing procedures. Also, because acid rain can etch and soften the paint, normal buffing or polishing repair procedures should not be attempted. This can cause further damage and result in visible depressions in the paint surface. The following are the three major categories of acid rain damage: •Minor damage: requires only buffing to repair. •Moderate damage: usually requires neutralizing, color sanding, and buffing. •Severe damage: extending beyond 1/2 mil of clearcoat on a pearl, metallic, or solid color, requires neutralization, sanding, and repainting. In cases where acid rain damage is minor, neutralization and buffing with a liquid-type paint finessing product may provide an adequate repair. Only specially formulated products outlined in this bulletin should be used for that purpose. Unfortunately, other than minor damage, there is no simple method of determining the actual extent (depth) of acid penetration other than color sanding a representative affected area until there is no visible etching or depressions, followed by measuring the amount of paint removed with either a magnetic or digital-type film thickness gauge. The procedures in this bulletin are intended for use by qualified body/paint technicians and should not be attempted by inexperienced personnel. While the quality and durability of paint on Toyota vehicles is continuously being improved, it remains the dealer’s responsibility to protect and maintain the quality of the vehicle’s paint finish after receipt at the dealership prior to the first sale. To read, While the quality and durability of paint on Toyota vehicles is continuously being improved, it remains the dealer’s responsibility to protect and maintain the quality of the vehicle’s paint finish after receipt at the dealership prior to first sale. Perform frequent vehicle washing, as often as daily, during high heat and humidity periods to minimize the potential for paint damage due to acid rain exposure. This is especially important in geographical areas known for high frequency and concentration of acid rain and industrial fallout.
T-SB-0038-24
Service Bulletin/Repair Instructions
To prevent brake rotor rust from forming during transportation and storage, wheel film will be used instead of a cardboard type of anti-rust cover. The purpose of the wheel film is to shield the disc brake rotor from weather elements and initial rust before the vehicle is delivered to the customer. Consequently, the film should remain on the wheel for as long as possible. SUPERSESSION NOTICE The information contained in this bulletin supersedes Service Bulletin No. PD017-04. •The entire bulletin has been updated.
T-SB-0039-24
Service Bulletin/Repair Instructions
The condition known as acid rain is caused by airborne chemicals or particles in the atmosphere, which mix with rainwater, nighttime dew, or high humidity to form acidic compounds. If these contaminants settle and remain on a painted vehicle surface, especially the horizonal areas of the hood, roof, and decklid, significant damage can occur. This damage is the result of actual etching of the paint and appears as pitting or water spots. As acid rain droplets on the vehicle surface evaporate, the concentration strength of the acid increases, causing deeper and more rapid damage. This evaporation and corrosive action also occur more rapidly on dark colored cars as direct sun heat increases. While Toyota paint quality, durability, and resistance to environmental factors is continuously being improved, it remains the responsibility of the dealer to protect and maintain the vehicle’s paint finish from the time of arrival at the dealership until retail delivery to the customer. In areas known for high frequency and/or concentration of acid rain (see Figure 1), frequent vehicle washing during high heat or humidity periods will minimize the potential for paint damage caused by acid rain. It is further recommended that either reverse osmosis or deionized water be used to prevent water spotting.
T-PANT-2024-004-
Service Bulletin/Repair Instructions
This is to advise of various price adjustments that will affect Toyota Genuine Motor Oil and Long Life Coolant, effective March 1, 2024. These products are ordered through the Toyota Complete Maintenance Care (TCMC) website.
T-SB-0043-14
Service Bulletin/Repair Instructions
OBSOLETE NOTICE January 22, 2024: This bulletin is now obsolete. Please see T-SB-0057-18.
TSB003220
Service Bulletin/Repair Instructions
TSB: Replacement certification labels (the vinyl label installed on the driver door or door post) and VIN plates (the metal plate riveted to dashboard) (see Figure 1) for most 1979 ? 2023 model year vehicles may be available provided the requests meet the criteria listed in this Service Bulletin. Follow the Procurement Procedure in this bulletin to request a replacement certification label or VIN plate.
TSB011219
Service Bulletin/Repair Instructions
TSB: Some 2005 ? 2023 model year Tacoma vehicles equipped with a manual transmission may exhibit a squeak or creak noise from the clutch pedal when it is depressed or released.
T-SB-0057-18
Service Bulletin/Repair Instructions
TSB: The Immobilizer and Smart Key Reset is a feature that allows the registration of new keys when all master keys are lost. Once the system is reset, all previously registered keys will be erased. Follow the procedures in this bulletin to reset a vehicle Immobilizer or Smart Key system.
T-SB-0094-21 Rev
Service Bulletin/Repair Instructions
TSB: Some 2005 ? 2022 model year Toyota vehicles that have undergone water intrusion may exhibit a condition in which a musty smell is present. Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this service bulletin is to provide general guidelines and procedures for odor remediation. This service bulletin provides a guide on how to prepare the interior of the vehicle prior to an odor remediation being performed, as well as contact information for an approved vendor who will arrange the remediation, and instructions on how to prepare the interior of the vehicle for reassembly once the remediation has been completed. Refer to all model and model year specific Repair Manuals and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines. This service bulletin is to provide a general overview and direction for the odor remediation process.
TSB009421Rev1
Service Bulletin/Repair Instructions
TSB: Some 2005 ? 2022 model year Toyota vehicles that have undergone water intrusion may exhibit a condition in which a musty smell is present. Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this service bulletin is to provide general guidelines and procedures for odor remediation. This service bulletin provides a guide on how to prepare the interior of the vehicle prior to an odor remediation being performed, as well as contact information for an approved vendor who will arrange the remediation, and instructions on how to prepare the interior of the vehicle for reassembly once the remediation has been completed. Refer to all model and model year specific Repair Manuals and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines. This service bulletin is to provide a general overview and direction for the odor remediation process
TTT063620
Service Bulletin/Repair Instructions
TT: Some Toyota vehicles installed with Toyota Complete Maintenance Care (TCMC) brake pads may exhibit a groan or squeak noise in various driving conditions
T-SB-0014-22
Service Bulletin/Repair Instructions
TSB: This Service Bulletin includes procedures to replace damaged or loose front carpet floor retainer(s) without replacing the carpet assembly. Follow the Repair Procedure in this bulletin to replace the loose or damaged carpet floor retainer(s).
T-SB-0397-09 Obs
Service Bulletin/Repair Instructions
OBSOLETE NOTICE Month 09, 2022: This bulletin is now obsolete. Please see T-SB-0014-22.
T-SB-0094-21
Service Bulletin/Repair Instructions
TSB: Some 2005 ? 2022 model year Toyota vehicles that have undergone water intrusion may exhibit a condition in which a musty smell is present. Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this service bulletin is to provide general guidelines and procedures for odor remediation. This service bulletin provides a guide on how to prepare the interior of the vehicle prior to an odor remediation being performed, as well as contact information for an approved vendor who will arrange the remediation, and instructions on how to prepare the interior of the vehicle for reassembly once the remediation has been completed. Refer to all model and model year specific Repair Manuals and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines. This service bulletin is to provide a general overview and direction for the odor remediation process.
Toyota Safety Re
Service Bulletin/Repair Instructions
Toyota Safety Recall and Service Campaign - Technician Certification Requirements
T-TT-0636-20 Rev
Service Bulletin/Repair Instructions
TT: Some Toyota vehicles installed with Toyota Complete Maintenance Care (TCMC) brake pads may exhibit a groan or squeak noise in various driving conditions.
T-SB-0040-08 Obs
Service Bulletin/Repair Instructions
OBSOLETE NOTICE March 08, 2021: This bulletin is now obsolete. Please see T-SB-0044-16.
T-SB-0032-20 Rev
Service Bulletin/Repair Instructions
TSB: Replacement certification labels (the vinyl label installed on the driver door or door post) and VIN plates (the metal plate riveted to dashboard) (see Figure 1) for most 1979 ? 2021 model year vehicles may be available provided the requests meet the criteria listed in this Service Bulletin. Follow the Procurement Procedure in this bulletin to request a replacement certification label or VIN plate.
T-TT-0636-20
Service Bulletin/Repair Instructions
TT: Some Toyota vehicles installed with Toyota Complete Maintenance Care (TCMC) brake pads may exhibit a groan or squeak noise in various driving conditions.
T-SB-0063-20
Service Bulletin/Repair Instructions
TSB: SUPERSESSION NOTICE The information contained in this bulletin supersedes Service Bulletin Nos. ST005-01, SU001-08, and T-SB-0391-08. The aforementioned bulletins are obsolete, and any printed versions should be discarded. Be sure to review the entire content of this service bulletin before proceeding. This Service Bulletin provides best practice procedures for vehicle pulling complaint, diagnosis, and repair for 2002 ? 2021 model year Toyota vehicles. This information supplements Repair Manual procedures when the symptoms are: ?Vehicle Pulling: The vehicle moves to the right or left when the driver holds the steering wheel while driving straight ahead without exerting steering effort. ?Steering Wheel Off Center: The vehicle travels straight, but the steering wheel is not pointed straight ahead. The vehicle is not pulling. Before repairing a vehicle pulling to one side, it is necessary to clearly identify the cause of the pulling condition. Frequently, pulling to one side is diagnosed as a wheel alignment concern. However, the actual cause may be related to the lateral force generated by the tires, vehicle damage, road crown or worn components. Performing a wheel alignment when tire force is the cause could result in the wheel alignment being set at a value outside of specifications. This could then cause other problems such as uneven tire wear, etc. A customer may notice a pull to the left when in the left lanes of travel and notice a pull to the right or no pull when traveling in the right lanes of travel on the very same section of roadway. This road crown effect is environmental and cannot be corrected with suspension adjustments or any other wheel or tire modification discussed in this bulletin.
T-SB-0391-08 Obs
Service Bulletin/Repair Instructions
TSB: OBSOLETE NOTICE June 23, 2020: This bulletin is now obsolete. Please see T-SB-0063-20.
DOR-M3J3F-07
Service Bulletin/Repair Instructions
These SKUs are Exhaust Manifolds with Catalytic Converters. The customer communication requested return of unsold inventory due to a loss of CARB certification. These SKUs can no longer be sold as they do not meet CARB standards, but parts on vehicles are not effected.
DOR-M9J4S-07
Service Bulletin/Repair Instructions
These SKUs are Exhaust Manifolds with Catalytic Converters. The customer communication requested return of unsold inventory due to a loss of CARB certification. These SKUs can no longer be sold as they do not meet CARB standards, but parts on vehicles are not effected.
Customer Support
Service Bulletin/Repair Instructions
DL: ZLZ Expired on 04/20/2020
T-SB-0304-17 Obs
Service Bulletin/Repair Instructions
TSB: OBSOLETE NOTICE April 07, 2020: This bulletin is now obsolete. Please see T-SB-0032-20. Replacement Certification Labels and VIN Plates
T-SB-0032-20
Service Bulletin/Repair Instructions
TSB: SUPERSESSION NOTICE The information contained in this bulletin supersedes Service Bulletin Nos. PG021-88, PG015-89, PG0015-90, PG002-91, PG002-93, PG005-97, PG007-01, PG007-07, PG006-01, PG004-97, T-SB-0144-08, and T-SB-0304-17. The aforementioned bulletins are obsolete, and any printed versions should be discarded. Replacement certification labels (the vinyl label installed on the driver door or door post) and VIN plates (the metal plate riveted to dashboard) (see Figure 1) for most 1979 ? 2020 model year vehicles may be available provided the requests meet the criteria listed in this Service Bulletin. Follow the Procurement Procedure in this bulletin to request a replacement certification label or VIN plate.
T-SB-0008-20
Service Bulletin/Repair Instructions
TSB: Vehicles may display evidence of a fluid leak or fluid seep from powertrain components. This bulletin explains how to determine the differences between a fluid leak versus a fluid seep. Cases that are determined to be a ?leak? should be repaired accordingly and will be covered under warranty if applicable. Cases that are determined to be a ?seep? should be documented on the repair order and inspected at the next service interval. Follow the Repair Information in this bulletin to determine if the concern in question is a fluid leak or fluid seep and review the Repair Procedure section to address the condition. NOTE This bulletin applies to ALL powertrain fluids excluding fuel and coolant.
T-SB-0112-19
Service Bulletin/Repair Instructions
TSB: SUPERSESSION NOTICE The information contained in this bulletin supersedes Service Bulletin No. T-SB-0186-12. * Applicability has been updated to include 2018 and 2019 model year Tacoma vehicles. * The entire bulletin has been updated. Service Bulletin No. T-SB-0186-12 is obsolete and any printed versions should be discarded. Some 2005 - 2019 model year Tacoma vehicles equipped with a manual transmission may exhibit a squeak or creak noise from the clutch pedal when it is depressed or released. Follow the Repair Procedure in this bulletin to address this condition.
T-SB-0186-12_Obs
Service Bulletin/Repair Instructions
TSB: OBSOLETE NOTICE August 19, 2019: This bulletin is now obsolete. Please see T-SB-0112-19.
T-SB-0134-16-Rev
Service Bulletin/Repair Instructions
TSB: REVISION NOTICE July 01, 2019 Rev2: ? Applicability has been updated to 2019 ? 2020 model year Toyota vehicles. ? The Techstream Preparation and Process Overview sections have been updated. October 30, 2017 Rev1: ? Applicability has been updated to include 2018 model year vehicles. Any previous printed versions of this bulletin should be discarded. SUPERSESSION NOTICE The information contained in this bulletin supersedes SB No. T-SB-0012-13. Service Bulletin No. T-SB-0012-13 is obsolete and any printed versions should be discarded. Be sure to review the entire content of this bulletin before proceeding. Flash reprogramming allows the Electronic Control Unit (ECU) software to be updated without replacing the ECU. Flash calibration updates for specific vehicle models/ECUs are released as field-fix procedures described in individual Service Bulletins. This bulletin details the Techstream ECU flash reprogramming process and outlines use of the Technical Information System (TIS) and the Calibration Update Wizard (CUW). Flash calibration updates can only be applied to the vehicle/ECU combination for which they are intended. ECUs have internal security that will not allow them to be programmed with another ECU?s information. NOTE ECU is a Toyota term used to describe integrated computerized devices responsible for managing the operation of a system or subsystem. For the purposes of this bulletin, the term ?ECU? is used as a generic label for the following SAE J1930 standard references: ? Powertrain Control Module (PCM) ? Engine Control Module (ECM) ? Transmission Control Module (TCM) ? Any other Toyota specific control unit
ZH6 05-10 Tacoma
Service Bulletin/Repair Instructions
Technical Instructions: Updated 06/12/19 TECHNICAL INSTRUCTIONS FOR WARRANTY ENHANCEMENT PROGRAM ZH6 * CERTAIN 2005 THROUGH 2010 MODEL YEAR TACOMA * FRAME REPLACEMENT
H0F_Expired_Deal
Service Bulletin/Repair Instructions
Dealer Package: May 22, 2019 A watermark has been added to the Dealer Letter to indicate that H0F expired on May 21, 2019. Toyota will initiate a Limited Service Campaign (LSC H0F) to apply Corrosion Resistant Compound to key areas of the vehicle?s frame for the following vehicles located in the 20 Cold Climate States1: ? Certain 2005 to 2010 Tacoma** - Available ? 2007 to 2008 Tundra ? Available ? 2005 to 2008 Sequoia ? Available On May 21, 2017, a settlement of claims in a class action lawsuit regarding frame corrosion was finally approved. This finally approved class action settlement includes inspection of the customer?s frame, and if the frame meets or exceeds the Rust Perforation Standard based on the Court-ordered inspection criteria, the frame will be replaced at no cost to the customer. This settlement will also include CRC (Corrosion Resistant Compound) application. The CRC application will only be available for vehicles registered in the Cold Climate States1 that pass frame inspection criteria, and did not: ? Previously have the frame replaced, if a Tacoma and/or: ? Previously had the frame sprayed with CRC under any previous campaign, if a Tacoma
H0F-Expired TI-1
Service Bulletin/Repair Instructions
Technical Instructions: TECHNICAL INSTRUCTIONS FOR CORROSION-RESISTANT COMPOUND CAMPAIGN H0F CERTAIN 2005 THROUGH 2010 MODEL YEAR TACOMA CORROSION-RESISTANT COMPOUND APPLICATION
H0F_Dealer Daily
Service Bulletin/Repair Instructions
Dealer Daily Message: Limited Service Campaign H0F ? Remedy Notice Certain 2005 ? 2010 Model Year Tacoma Certain 2007 ? 2008 Model Year Tundra Certain 2005 ? 2008 Model Year Sequoia Frame Corrosion Resistant Compound (CRC) Application ? LSC H0F will expire May 21, 2019. ? No vehicles can be sprayed after this date. It?s important to have all vehicles remaining to be sprayed completed on or before this date. o If your dealership is not able to spray the remaining vehicles before this expiration, consideration can be given into whether a customer should be referred to another, local Toyota dealership that can complete the CRC application on or before May 21, 2019. ? Ensure your dealership only orders CRC spray for vehicles that are scheduled to be sprayed. Any additional CRC spray kits cannot be returned after campaign expiration.
ZH6_Toyota POL17
Service Bulletin/Repair Instructions
Warranty Policy Bulletin: Toyota has received reports of customer concerns in which the vehicles operated in specific cold climate areas (Cold Climate States) with high road salt usage may exhibit more-than-normal corrosion with the vehicle?s frame. On May 21, 2017, a settlement of claims in a class action lawsuit involving 2005 ? 2010 Toyota Tacoma vehicles regarding frame corrosion was approved. This class action settlement includes inspection of the customer?s frame, and if the frames meet or exceed the Rust Perforation Standard based on the Court ordered inspection criteria, the frame will be replaced at no cost to the customer. Toyota is currently preparing parts for frame replacement. This settlement will also include CRC (Corrosion Resistant Compound) application. Toyota is currently preparing parts for CRC application process. Once available, CRC application will be covered under a separate Limited Service Campaign (LSC), and will only be available for vehicles registered in the Cold Climate States1 that pass frame inspection criteria, and did not: ? Previously have the frame replaced and/or: ? Previously had the frame sprayed with CRC under any previous campaign
H0F_Dealer Packa
Service Bulletin/Repair Instructions
Dealer Package: Added important note in the Parts section. Toyota will initiate a Limited Service Campaign (LSC H0F) to apply Corrosion Resistant Compound to key areas of the vehicle?s frame for the following vehicles located in the 20 Cold Climate States1: ? Certain 2005 to 2010 Tacoma** - Available ? 2007 to 2008 Tundra ? Available ? 2005 to 2008 Sequoia ? Available On May 21, 2017, a settlement of claims in a class action lawsuit regarding frame corrosion was finally approved. This finally approved class action settlement includes inspection of the customer?s frame, and if the frame meets or exceeds the Rust Perforation Standard based on the Court-ordered inspection criteria, the frame will be replaced at no cost to the customer.
ZH6_Dealer Packa
Service Bulletin/Repair Instructions
Dealer Package: Modified warranty claim submission flowchart. See Appendix A. In our continuing efforts to ensure the best in customer satisfaction, Toyota is announcing a Warranty Enhancement Program to extend the warranty coverage for Frame Corrosion on certain 2005 ? 2010 model year Tacoma vehicles. On May 21, 2017, a settlement of claims in a class action lawsuit involving 2005 ? 2010 Toyota Tacoma vehicles regarding frame corrosion was approved. This finally approved class action settlement includes inspection of the customer?s frame, and if the frames meet or exceed the Rust Perforation Standard based on the Court-ordered inspection criteria, the frame will be replaced at no cost to the customer. This settlement will also include CRC (Corrosion Resistant Compound) application. Toyota is currently preparing parts for CRC application process. CRC application will be covered under a separate Limited Service Campaign (LSC ? H0F), and will only be available for vehicles registered in the Cold Climate States1 that pass frame inspection criteria, and did not: ? Previously have the frame replaced and/or: ? Previously had the frame sprayed with CRC under any previous campaign
ZH2-Dealer Packa
Service Bulletin/Repair Instructions
Dealer Package: 09/14/2018 The note in the ?Parts Ordering Process? section to reference POL17-16 to determine the applicable U-joint kit part # has been removed. T-SB-0302-17 has been updated with this information. Toyota has received a number of reports regarding Propeller Shaft Universal Joints on certain 2005 ? 2011 model year Tacoma vehicles. In these reports, customers have indicated that there is a drivetrain vibration and/or drivetrain noise. If the vehicle continues to be driven with the aforementioned condition, there is risk of severe damage to the propeller shaft. Although the Propeller Shaft Universal Joints are covered by Toyota?s Powertrain Limited Warranty for 5 years or 60,000 miles (whichever occurs first), we at Toyota care about the customers? ownership experience. Toyota is now providing coverage for repairs related to this condition. The following information is provided to inform you and your staff of the program notification schedule and your degree of involvement.
ZH2-Toyota POL17
Service Bulletin/Repair Instructions
Customer Support Program: Toyota has received reports in which customers have indicated that there is a drivetrain vibration and/or drivetrain noise. If the vehicle continues to be driven with the aforementioned condition, there is risk of severe damage to the propeller shaft.
PG004-97-Obsolet
Service Bulletin/Repair Instructions
Technical Service Bulletin: OBSOLETE NOTICE: July 31, 2018: This bulletin is now obsolete. Please see T-SB-0304-17.
PG006-01-Obsolet
Service Bulletin/Repair Instructions
Technical Service Bulletin: OBSOLETE NOTICE: July 31, 2018: This bulletin is now obsolete. Please see T-SB-0304-17.
H0F_CRC_Spray De
Service Bulletin/Repair Instructions
CRC Spray Application Preparation. Frame Corrosion Resistant Compound (CRC) Application. Please reference the included CRC Readiness Checklist and FAQ (Frequently Asked Question). These documents should be used to prepare your dealership for CRC spray application.
T-SB-0304-17_Rev
Service Bulletin/Repair Instructions
TSB: REVISION NOTICE July 31, 2018 Rev2: ? The Supersession Notice has been updated. January 11, 2018 Rev1: ? The Supersession Notice has been updated. Any previous printed versions of this bulletin should be discarded. SUPERSESSION NOTICE The information contained in this bulletin supersedes Service Bulletin Nos. PG021-88, PG015-89, PG0015-90, PG002-91, PG002-93, PG005-97, PG007-01, PG007-07, PG006-01, PG004-97, and T-SB-0144-08. Service Bulletin Nos. PG021-88, PG015-89, PG0015-90, PG002-91, PG002-93, PG005-97, PG007-01, PG007-07, PG006-01, PG004-97, and T-SB-0144-08 are obsolete and any printed versions should be discarded. Vehicle replacement certification labels (the vinyl label installed on the driver door or door post) and VIN plates (the metal plate riveted to dashboard) may be available from Toyota, provided the request meets one of the criteria listed in this Service Bulletin. Replacement Certification Label and VIN Plate Criteria A replacement certification label and/or VIN plate may be requested if: ? The vehicle was in an accident and the label and/or plate is damaged or attached to a part that will be replaced during the repair. ? The label and/or plate was stolen.
T-SB-0302-17-Rev
Service Bulletin/Repair Instructions
TSB: REVISION NOTICE June 27, 2018 Rev2: ? The Production Change Information and the Parts Information sections have been updated. March 14, 2018 Rev1: ? The Production Change Information and Repair Procedure sections have been updated. Any previous printed versions of this bulletin should be discarded. Some 2005 ? 2011 model year Tacoma vehicles may exhibit a condition where there is a drivetrain vibration and/or drivetrain noise. Follow the procedure in this bulletin to address this condition.
ZH6-Toyota POL17
Service Bulletin/Repair Instructions
Warranty Policy Bulletin: Toyota has received reports of customer concerns in which the vehicles operated in specific cold climate areas (Cold Climate States) with high road salt usage may exhibit more-than-normal corrosion with the vehicle?s frame. On May 21, 2017, a settlement of claims in a class action lawsuit involving 2005 ? 2010 Toyota Tacoma vehicles regarding frame corrosion was approved. This class action settlement includes inspection of the customer?s frame, and if the frames meet or exceed the Rust Perforation Standard based on the Court ordered inspection criteria, the frame will be replaced at no cost to the customer. Toyota is currently preparing parts for frame replacement. This settlement will also include CRC (Corrosion Resistant Compound) application. Toyota is currently preparing parts for CRC application process. Once available, CRC application will be covered under a separate Limited Service Campaign (LSC), and will only be available for vehicles registered in the Cold Climate States1 that pass frame inspection criteria, and did not: ? Previously have the frame replaced and/or: ? Previously had the frame sprayed with CRC under any previous campaign
Frame Campaign W
Service Bulletin/Repair Instructions
Dealer Daily Message: Frame Warranty Claim Submission The information below should be referenced to ensure correct warranty claim submissions for frame replacement or spray campaigns (ZH6-9 and H0F). Key Points ? DO NOT perform Campaign H0F without first performing and filing a claim for the WEP (Warranty Enhancement Programs ZH6-9) inspection. ? H0F Op Codes GGG44C, GGG45C, GGG46C, GGG47C, and GGG48C are for vehicles that had initially passed the WEP inspection, but had perforation found when descaling the vehicle in preparation for the CRC spray. These H0F Op codes are not to be used as a preliminary failed inspection. ? If you see in TIS that campaign H0F is applicable and the status shows Not Completed, check to see the status of WEP ZH6-9. Please follow the flowchart below for the correct frame inspection, replacement, and CRC spray process.
H0F-Dealer Packa
Service Bulletin/Repair Instructions
Dealer Package: June 25, 2018 Added warranty claim submission flowchart. See Appendix A. Toyota will initiate a Limited Service Campaign (LSC H0F) to apply Corrosion Resistant Compound to key areas of the vehicle?s frame for the following vehicles located in the 20 Cold Climate States1: ? Certain 2005 to 2010 Tacoma** - Available ? 2007 to 2008 Tundra ? Available ? 2005 to 2008 Sequoia ? Available On May 21, 2017, a settlement of claims in a class action lawsuit regarding frame corrosion was finally approved. This finally approved class action settlement includes inspection of the customer?s frame, and if the frame meets or exceeds the Rust Perforation Standard based on the Court-ordered inspection criteria, the frame will be replaced at no cost to the customer.
ZH2_Toyota POL17
Service Bulletin/Repair Instructions
Warranty Policy Bulletin: Toyota has received reports in which customers have indicated that there is a drivetrain vibration and/or drivetrain noise. If the vehicle continues to be driven with the aforementioned condition, there is risk of severe damage to the propeller shaft.
Toyota PRO18-03_
Service Bulletin/Repair Instructions
Mis-Built For frames that are suspected to have been mis-built, dealers should: 1. Contact the Parts Technical Support Group (PTSG) at prasupport@toyota.com with information on the condition and status of repair. a. Include the original part order reference number. 2. A Field Product Quality Report (FPQR) should be generated and attached to the communication. a. The report should include photos of the condition and of all labels and stampings on the frame. b. This report can be submitted by region staff (FTS) or dealership personnel. 3. Dealership will receive communication back with next direction(s) from PTSG. a. Response will include confirmation of mis-built condition and if applicable,
T-SB-0026-15_Rev
Service Bulletin/Repair Instructions
TSB: REVISION NOTICE June 8, 2018 Rev2: ? Applicability has been updated to exclude 2016 ? 2017 model year Tacoma vehicles. ? The Repair Procedure section has been updated. May 15, 2017 Rev1: ? Applicability has been updated to include 2016 ? 2017 model year Tacoma and 4Runner vehicles. ? The Introduction section has been updated. Any previous printed versions of this bulletin should be discarded. Some 2004 ? 2017 model year 4Runner vehicles, 2007 ? 2014 model year FJ Cruiser vehicles, and 2005 ? 2015 model year Tacoma vehicles equipped with part-time 4WD may exhibit a cyclical groaning or grinding noise coming from the front differential in 2WD that goes away when operated in 4WD. This noise can be addressed by replacing the needle bearing on the left side of the front differential. Refer to the Repair Procedure for needle bearing roller replacement instructions.
ZH2_Dealer Daily
Service Bulletin/Repair Instructions
Dealer Daily Message: Certain U-joint kits (campaign part # 04007-13204) used in Customer Support Program ZH2 may have been produced without the appropriate amount of grease. These parts should not be installed on vehicles. Previously we requested that dealers return their current stock of this part number that does not have a GREEN dot on the box and on the U-joint as indicated in the photos on the following page. The supplier is now marking this part number with a BLUE dot on the U-joint, and no marking on the box as indicated in the photo on the following page. If either of these markings ARE NOT present, dealers should return the part. If either of these marking ARE NOT present, your facing PDC (Parts Distribution Center) may create a manual R8 exception return for these parts, and you can return them to your facing PDC for credit. Toyota is working to stock new inventory of these parts. Note that grease should not be added to these U-joint kits. They are designed to have the appropriate amount of grease applied during production and are non-serviceable.
T-SB-0040-18
Service Bulletin/Repair Instructions
TSB: Referencing this Service Bulletin provides best practice procedures when reassembling and installing the front shock absorber with coil spring. Some 2005 - 2015 model year Tacoma vehicles with applicable VDS have a different coil spring diameter. This may lead to a lateral force applied to the support plate upon reassembly of the front shock absorber with coil spring assembly. This may cause the inner rubber sleeve of the support plate to pull out when spring tension is released and the support plate to tilt. NOTE This Service Bulletin ONLY provides best practices for front shock absorber with coil spring assembly. The Repair Manual MUST be referenced with this bulletin when performing front shock absorber with coil spring assembly replacement.
ZH6, ZH7, ZH8, Z
Service Bulletin/Repair Instructions
Dealer Daily Message: Frame Programs. Extension of Warranty Coverage for Frame Corrosion/Frame Replacement. Frame Ordering/Repair/Administration Updates Mis-Built. For frames that are suspected to have been mis-built, dealers should: 1. Contact the Parts Technical Support Group (PTSG) at prasupport@toyota.com with information on the condition and status of repair. Also include the original part order reference number. a. A Field Product Quality Report (FPQR) should also be generated and attached to the communication. i. The report should include photos of the condition, and photos of all labels and stampings on the frame. ii. This report can be submitted by region staff (FTS) or dealership personnel. 2. Dealership will receive communication back with next direction(s) from PTSG. a. Response will include confirmation of mis-built condition, if applicable, and instructions on mis-built frame disposition.
ZH6-306-18
Service Bulletin/Repair Instructions
Brake line color codes.
ZH6_Dealer Packe
Service Bulletin/Repair Instructions
Dealer Letter: March 2, 2018. Rental sublet period added for use during repair. ? Primary Coverage expiration date changed. ? Ancillary parts coverage section added. Warranty Enhancement Program ZH6 Certain 2005 ? 2010 Model Year Tacoma Extension of Warranty Coverage for Frame Corrosion. In our continuing efforts to ensure the best in customer satisfaction, Toyota is announcing a Warranty Enhancement Program to extend the warranty coverage for Frame Corrosion on certain 2005 ? 2010 model year Tacoma vehicles. On May 21, 2017, a settlement of claims in a class action lawsuit involving 2005 ? 2010 Toyota Tacoma vehicles regarding frame corrosion was approved. This finally approved class action settlement includes inspection of the customer?s frame, and if the frames meet or exceed the Rust Perforation Standard based on the Court-ordered inspection criteria, the frame will be replaced at no cost to the customer. This settlement will also include CRC (Corrosion Resistant Compound) application. Toyota is currently preparing parts for CRC application process. CRC application will be covered under a separate Limited Service Campaign (LSC ? H0F), and will only be available for vehicles registered in the Cold Climate States1 that pass frame inspection criteria, and did not: ? Previously have the frame replaced and/or: ? Previously had the frame sprayed with CRC under any previous campaign
ZH6_05-10_Tacoma
Service Bulletin/Repair Instructions
Technical Instructions: Update 3-1-18 - Frame part numbers corrected. TECHNICAL INSTRUCTIONS FOR WARRANTY ENHANCEMENT PROGRAM ZH6. CERTAIN 2005 THROUGH 2010 MODEL YEAR TACOMA. FRAME REPLACEMENT.
ZH6_Dealer Daily
Service Bulletin/Repair Instructions
Dealer Daily Message: UPDATED Dealer Daily - DO NOT USE BRAKE LINES WITH WHITE MARK Warranty Enhancement Programs ZH6 - Certain 2005 ? 2010 Model Year Tacoma Vehicles Extension of Warranty Coverage for Frame Corrosion. A Brake Line used in certain 2005-2008 model year Tacoma frame replacement repairs has changed. Part Number: 47323-04160 (TUBE, RR BRAKE, No.3). In a previous Dealer Daily (published Feb. 26, 2018), we notified that the new brake lines for this repair will have a white mark as indicated in the photos below. We received notification that these brake lines with a white dot should not be used.
ZH6_Brake Line U
Service Bulletin/Repair Instructions
Dealer Daily Message: Warranty Enhancement Programs ZH6 - Certain 2005 ? 2010 Model Year Tacoma Vehicles. Extension of Warranty Coverage for Frame Corrosion. 2005-2008 Tacoma Frame Repair ? Brake Line Update. A Brake Line used in certain 2005-2008 model year Tacoma frame replacement repairs has changed.
T-SB-0186-12_Rev
Service Bulletin/Repair Instructions
TSB: REVISION NOTICE February 21, 2018 Rev2: ? Applicability has been updated to include 2015 ? 2017 model year Tacoma vehicles. ? The Parts Information and Repair Procedure sections have been updated. September 10, 2014 Rev1: ? Applicability has been updated to include 2013 ? 2014 model year Tacoma vehicles. ? The Warranty Information, Parts Information, and the Repair Procedure sections have been updated. Any previous printed versions of this bulletin should be discarded. SUPERSESSION NOTICE The information contained in this bulletin supersedes SB No. TC004-06. ? Applicability has been updated to include 2007 ? 2012 model year Tacoma vehicles. ? The Repair Procedure section has been updated. Service Bulletin No. TC004-06 is obsolete and any printed versions should be discarded. Be sure to review the entire content of this bulletin before proceeding. Some 2005 ? 2017 model year Tacoma vehicles may exhibit a squeak or creak noise from the clutch pedal when it is depressed or released. Follow the Repair Procedure in this bulletin to address this condition.
ZH6_Tacoma Frame
Service Bulletin/Repair Instructions
Technical Instructions: Technical Instructions for Warranty Enhancement Program ZH6. Certain 2005 through 2010 Model Year Tacoma. UPDATED 2-15-2018. Frame Replacement.
T-SB-0187-12_Rev
Service Bulletin/Repair Instructions
TSB: REVISION NOTICE February 12, 2018 Rev2: ? Applicability has been updated to include 2015 ? 2018 model year vehicles. January 23, 2014 Rev1: ? Applicability has been updated to include 2013 ? 2014 model year vehicles. Any previous printed versions of this bulletin should be discarded. Toyota vehicles are equipped with either conventional or run-flat tires. Sometimes punctures may occur as a result of contact with road debris or other hazards. If a puncture occurs, it may be possible to repair the tire and return it to service. With a conventional tire it is not possible to drive for an extended amount of time with the tire at low pressures as damage to the tire may occur. With run-flat tires, due to reinforced sidewalls, it is possible to drive for up to 100 miles at speeds less than 55 mph with little or no damage to the tire. The U.S. Tire Manufacturers Association (UTSMA) provides guidelines and recommendations for tire repair and replacement. It also provides information related to: ? Basic tire information ? Tire maintenance and safety ? Driver education, tire safety curriculum.
H0F Dealer Lette
Service Bulletin/Repair Instructions
Dealer Letter: December 14, 2017. ? Technician Certification Requirements updated. ? Instructions added for CRC Spray Gun/Parts replacement requests.
HOF Dealer Lette
Service Bulletin/Repair Instructions
Dealer Letter: December 14, 2017. Technician Certification Requirements updated. Instructions added for CRC Spray Gun/Parts replacement requests.
TSR-1212-17
Service Bulletin/Repair Instructions
Technician Certification Requirements.
Tacoma CRC_Techn
Service Bulletin/Repair Instructions
Technical Instructions: Corrosion-Resistant Compound Campaign H0F Certain 2005- 2010 Model Year Tacoma. CORROSION-RESISTANT COMPOUND APPLICATION.
T-SB-0229-12_Rev
Service Bulletin/Repair Instructions
TSB: REVISION NOTICE November 22, 2017 Rev1: ? Applicability has been updated to include 2014 ? 2018 model year vehicles. Any previous printed versions of this bulletin should be discarded. In the event that a Toyota vehicle becomes submerged in water, many components may be physically damaged. Electrical and electronic components, including wiring harnesses, are particularly susceptible to corrosion and subsequent malfunction. Although any flooding can be damaging, salt water flooding elevates the potential for abnormal conditions and may increase risks due to its highly corrosive and conductive nature. Salt residue also continues to corrode and remain conductive even after a vehicle dries. This bulletin is intended to assist with safe handling and inspection of flood damaged vehicles and to provide basic guidance on likely needed repairs.
T-SB-0144-08_Obs
Service Bulletin/Repair Instructions
TSB: OBSOLETE NOTICE November 21, 2017: This bulletin is now obsolete. Please see T-SB-0304-17.
T-SB-0134-16_Rev
Service Bulletin/Repair Instructions
TSB: REVISION NOTICE October 30, 2017 Rev1: * Applicability has been updated to include 2018 model year vehicles. SUPERSESSION NOTICE The information contained in this bulletin supersedes SB No. T-SB-0012-13. Flash reprogramming allows the Electronic Control Unit (ECU) software to be updated without replacing the ECU. Flash calibration updates for specific vehicle models/ECUs are released as field-fix procedures described in individual Service Bulletins. This bulletin details the Techstream ECU flash reprogramming process and outlines use of the Technical Information System (TIS) and the Calibration Update Wizard (CUW). Flash calibration updates can only be applied to the vehicle/ECU combination for which they are intended. ECUs have internal security that will not allow them to be programmed with another ECU's information.
ZH2-DPR-914-18
Service Bulletin/Repair Instructions
Updated dealer letter
ZH2-POL17-16
Service Bulletin/Repair Instructions
There is a drivetrain vibration and/or noise.
ZH2_Dealer Email
Service Bulletin/Repair Instructions
Dealer Email: Toyota has received a number of reports regarding Propeller Shaft Universal Joints on certain 2005 ? 2011 model year Tacoma vehicles. In these reports, customers have indicated that there is a drivetrain vibration and/or drivetrain noise. If the vehicle continues to be driven with the aforementioned condition, there is risk of severe damage to the propeller shaft. Although the Propeller Shaft Universal Joints are covered by Toyota?s Powertrain Limited Warranty for 5 years or 60,000 miles (whichever occurs first), we at Toyota care about the customers? ownership experience. Toyota is now providing coverage for repairs related to this condition.
ZH2_Dealer Lette
Service Bulletin/Repair Instructions
Dealer Letter: Toyota has received a number of reports regarding Propeller Shaft Universal Joints on certain 2005 ? 2011 model year Tacoma vehicles. In these reports, customers have indicated that there is a drivetrain vibration and/or drivetrain noise. If the vehicle continues to be driven with the aforementioned condition, there is risk of severe damage to the propeller shaft. Although the Propeller Shaft Universal Joints are covered by Toyota?s Powertrain Limited Warranty for 5 years or 60,000 miles (whichever occurs first), we at Toyota care about the customers? ownership experience. Toyota is now providing coverage for repairs related to this condition.
ZH2_Region Email
Service Bulletin/Repair Instructions
Region Email: Toyota has received a number of reports regarding Propeller Shaft Universal Joints on certain 2005 ? 2011 model year Tacoma vehicles. In these reports, customers have indicated that there is a drivetrain vibration and/or drivetrain noise. If the vehicle continues to be driven with the aforementioned condition, there is risk of severe damage to the propeller shaft. Although the Propeller Shaft Universal Joints are covered by Toyota?s Powertrain Limited Warranty for 5 years or 60,000 miles (whichever occurs first), we at Toyota care about the customers? ownership experience. Toyota is now providing coverage for repairs related to this condition.
ZH2_Region Lette
Service Bulletin/Repair Instructions
Region Letter: Toyota has received a number of reports regarding Propeller Shaft Universal Joints on certain 2005 ? 2011 model year Tacoma vehicles. In these reports, customers have indicated that there is a drivetrain vibration and/or drivetrain noise. If the vehicle continues to be driven with the aforementioned condition, there is risk of severe damage to the propeller shaft. Although the Propeller Shaft Universal Joints are covered by Toyota?s Powertrain Limited Warranty for 5 years or 60,000 miles (whichever occurs first), we at Toyota care about the customers? ownership experience. Toyota is now providing coverage for repairs related to this condition.
T-SB-0304-17
Service Bulletin/Repair Instructions
TSB: Vehicle replacement certification labels (the vinyl label installed on the driver door or door post) and VIN plates (the metal plate riveted to dashboard) may be available from Toyota, provided the request meets one of the criteria listed in this Service Bulletin.
T-SB-0302-17
Service Bulletin/Repair Instructions
TSB: Some 2005 ? 2011 model year Tacoma vehicles may exhibit a condition where there is a drivetrain vibration and/or drivetrain noise.
H0F_Dealer Lette
Service Bulletin/Repair Instructions
Dealer Letter: October 19, 2018 Tundra (ZH7) Frame Replacement and CRC Application is now available. Toyota will initiate a Limited Service Campaign (LSC H0F) to apply Corrosion Resistant Compound to key areas of the vehicle?s frame for the following vehicles located in the 20 Cold Climate States1: ? Certain 2005 to 2010 Tacoma** - Available ? 2007 to 2008 Tundra ? Available ? 2005 to 2008 Sequoia ? Available. On May 21, 2017, a settlement of claims in a class action lawsuit regarding frame corrosion was finally approved. This finally approved class action settlement includes inspection of the customer?s frame, and if the frame meets or exceeds the Rust Perforation Standard based on the Court-ordered inspection criteria, the frame will be replaced at no cost to the customer.
ZH7_Dealer Email
Service Bulletin/Repair Instructions
Dealer Email: ? 2007-2008 (ZH7) Tundra Frame Replacement and CRC Application is now available. On May 21, 2017, a settlement of claims in a class action lawsuit involving 2005 ? 2010 Toyota Tacoma, 2007-2008 Tundra, and 2005-2008 Sequoia vehicles regarding frame corrosion was approved. This finally approved class action settlement includes inspection of the customer?s frame, and if the frames meet or exceed the Rust Perforation Standard based upon the Court-ordered inspection criteria, the frame will be replaced at no cost to the customer. This settlement will also include CRC (Corrosion Resistant Compound) application. Once available, CRC application will be covered under a separate Limited Service Campaign (LSC), and will only be available for vehicles registered in the Cold Climate States1 that pass frame inspection criteria.
ZH7_Region Email
Service Bulletin/Repair Instructions
Region Email: ? 2007-2008 (ZH7) Tundra Frame Replacement and CRC Application is now available. On May 21, 2017, a settlement of claims in a class action lawsuit involving 2005 ? 2010 Toyota Tacoma, 2007-2008 Tundra, and 2005-2008 Sequoia vehicles regarding frame corrosion was approved. This finally approved class action settlement includes inspection of the customer?s frame, and if the frames meet or exceed the Rust Perforation Standard based upon the Court-ordered inspection criteria, the frame will be replaced at no cost to the customer. This settlement will also include CRC (Corrosion Resistant Compound) application. Once available, CRC application will be covered under a separate Limited Service Campaign (LSC), and will only be available for vehicles registered in the Cold Climate States1 that pass frame inspection criteria.
ZH7_Region Lette
Service Bulletin/Repair Instructions
Region Letter: October 19,2017 Tundra Frame Replacement (ZH7) and CRC Application is now available. ? Added additional op codes for Tundra to cover dealer costs of maintaining vehicles while waiting for frames, if applicable. ? Added op codes for Tundra to cover costs to replace Bed Assembly, if applicable. On May 21, 2017, a settlement of claims in a class action lawsuit involving 2005 ? 2010 Toyota Tacoma, 2007-2008 Tundra, and 2005-2008 Sequoia vehicles regarding frame corrosion was approved. This finally approved class action settlement includes inspection of the customer?s frame, and if the frames meet or exceed the Rust Perforation Standard based upon the Court-ordered inspection criteria, the frame will be replaced at no cost to the customer. Toyota is currently preparing parts for frame replacement
ZH8 and ZH9_Deal
Service Bulletin/Repair Instructions
Dealer Email: ? 2005-2007 (ZH8) Sequoia Frame Replacement and CRC Application is now available. ? 2008 (ZH9) Sequoia Frame Replacement and CRC Application is now available. On May 21, 2017, a settlement of claims in a class action lawsuit involving 2005 ? 2010 Toyota Tacoma, 2007-2008 Tundra, and 2005-2008 Sequoia vehicles regarding frame corrosion was approved. This finally approved class action settlement includes inspection of the customer?s frame, and if the frames meet or exceed the Rust Perforation Standard based upon the Court-ordered inspection criteria, the frame will be replaced at no cost to the customer. This settlement will also include CRC (Corrosion Resistant Compound) application. Toyota is currently preparing parts for the CRC application process. Once available, CRC application will be covered under a separate Limited Service Campaign (LSC), and will only be available for vehicles registered in the Cold Climate States1 that pass frame inspection criteria.
ZH8 and ZH9_Regi
Service Bulletin/Repair Instructions
Region Email: ? 2005-2007 (ZH8) Sequoia Frame Replacement and CRC Application is now available. ? 2008 (ZH9) Sequoia Frame Replacement and CRC Application is now available. On May 21, 2017, a settlement of claims in a class action lawsuit involving 2005 ? 2010 Toyota Tacoma, 2007-2008 Tundra, and 2005-2008 Sequoia vehicles regarding frame corrosion was approved. This finally approved class action settlement includes inspection of the customer?s frame, and if the frames meet or exceed the Rust Perforation Standard based upon the Court-ordered inspection criteria, the frame will be replaced at no cost to the customer. This settlement will also include CRC (Corrosion Resistant Compound) application. Toyota is currently preparing parts for the CRC application process. Once available, CRC application will be covered under a separate Limited Service Campaign (LSC), and will only be available for vehicles registered in the Cold Climate States1 that pass frame inspection criteria.
ZH8_Region Lette
Service Bulletin/Repair Instructions
Region Letter: October 12,2017 Sequoia Frame Replacement (ZH8 and ZH9) is now available. ? Added additional op codes for Sequoia to cover dealer costs of maintaining vehicles while waiting for frames, if applicable. Specific information for Region support is provided below. On May 21, 2017, a settlement of claims in a class action lawsuit involving 2005 ? 2010 Toyota Tacoma, 2007-2008 Tundra, and 2005-2008 Sequoia vehicles regarding frame corrosion was approved. This finally approved class action settlement includes inspection of the customer?s frame, and if the frames meet or exceed the Rust Perforation Standard based upon the Court-ordered inspection criteria, the frame will be replaced at no cost to the customer. Toyota is currently preparing parts for frame replacement.
ZH6_Dealer Lette
Service Bulletin/Repair Instructions
Dealer Letter: The attached Dealer Letter has been updated. September 29, 2017 Rental Invoice requirement has been added. ? Estimated Launch Timing has been updated for Tundra and Sequoia models.
H0F_PA Dealer Le
Service Bulletin/Repair Instructions
Dealer Letter: This communication only applies to dealerships located in Pennsylvania. As discussed in our August 28, 2017 Dealer Daily message, dealers in Pennsylvania were required to wait to commence CRC application for the H0F campaign until after expiration of a 15 working-day notification period. Notices regarding the H0F campaign were submitted to the Pennsylvania Department of Environmental Protection (PADEP), Allegheny County Health Department (ACHD) and Philadelphia Air Management Services (PAMS) on August 25, 2017. Accordingly, the 15-day period has now expired and you may commence offering the CRC applications at your dealership.
H0F_ West Virgin
Service Bulletin/Repair Instructions
Dealer Letter: Toyota has received a letter dated September 8, 2017 from the West Virginia Department of Environmental Protection (WVDAQ), confirming that the H0F campaign is exempt from air permit requirements as long as Toyota dealers comply with all conditions set forth in the WVDAQ letter. Your dealership will be able to do so by (1) keeping a copy of this WVDAQ letter in your records for the H0F campaign and (2) following all instructions in the Dealer Information Packet.
H0F_Massachusett
Service Bulletin/Repair Instructions
Dealer Letter: Toyota has received a letter dated September 5, 2017 from the Massachusetts Department of Environmental Protection (MADEP), confirming that the H0F campaign is exempt from air permit requirements as long as Toyota dealers comply with all conditions set forth in the MADEP letter. Your dealership will be able to do so by (1) keeping a copy of this MADEP letter in your records for the H0F and (2) following all instructions in the Dealer Information Packet.
ZH6_Tacoma_Frame
Service Bulletin/Repair Instructions
Reference Guide: ASM Reference Guide for Warranty Extension Program (WEP) ZH6 - Covered Components: if Frame Replacement is Needed.
H0F-083117
Service Bulletin/Repair Instructions
Technical Instructions for Limited Service Campaign
ZH6-Dealer Daily
Service Bulletin/Repair Instructions
Dealer Letter: Extension of Warranty Coverage for Frame Corrosion. Technician Training Requirements have been updated to reflect amendments to the post-repair sign off and validation procedure.
ZH6-Frame Replac
Service Bulletin/Repair Instructions
Dealer Letter: ZH6 Frame Replacement Checksheet
H0F-CRC-State Re
Service Bulletin/Repair Instructions
Dealer Letter: Frame Corrosion Resistant Compound (CRC) Application. As with prior CRC campaigns, the H0F Corrosion Resistant Compound (CRC) campaign is subject to state and local air emissions and permitting requirements. These requirements vary, and in the following regions, CRC application for the H0F may not yet begin, as Toyota is still waiting for certain approvals/notifications: ? Massachusetts ? West Virginia.
H0F-Dealer Daily
Service Bulletin/Repair Instructions
Dealer Letter: Frame Corrosion Resistant Compound (CRC) Application. As part of the H0F Corrosion Resistant Compound (CRC) program, your dealership will receive a new set of the Vaupel HSDR 3300 spray guns to replace the old set of spray guns used for prior CRC campaigns and currently in your possession. You should use this new set of spray guns to conduct the H0F and any future CRC campaigns.
H0F-Dealer Email
Service Bulletin/Repair Instructions
Dealer Email: Toyota will initiate a Limited Service Campaign (LSC H0F) to apply Corrosion Resistant Compound to key areas of the vehicle?s frame for the following vehicles located in the 20 Cold Climate States1: ? Certain 2005 to 2010 Tacoma** - Available ? 2007 to 2008 Tundra ? Not Yet Available ? 2005 to 2008 Sequoia ? Not Yet Available.
H0F-Dealer Lette
Service Bulletin/Repair Instructions
Dealer Letter: Toyota will initiate a Limited Service Campaign (LSC H0F) to apply Corrosion Resistant Compound to key areas of the vehicle?s frame for the following vehicles located in the 20 Cold Climate States1: ? Certain 2005 to 2010 Tacoma** - Available ? 2007 to 2008 Tundra ? Not Yet Available ? 2005 to 2008 Sequoia ? Not Yet Available.
H0F-Region Email
Service Bulletin/Repair Instructions
Region Email: Toyota will initiate a Limited Service Campaign (LSC H0F) to apply Corrosion Resistant Compound to key areas of the vehicle?s frame for the following vehicles located in the 20 Cold Climate States1: ? Certain 2005 to 2010 Tacoma** - Available ? 2007 to 2008 Tundra ? Not Yet Available ? 2005 to 2008 Sequoia ? Not Yet Available.
H0F-Region Lette
Service Bulletin/Repair Instructions
Region Letter: Toyota will initiate a Limited Service Campaign (LSC H0F) to apply Corrosion Resistant Compound to key areas of the vehicle?s frame for the following vehicles located in the 20 Cold Climate States1: ? Certain 2005 to 2010 Tacoma** - Available ? 2007 to 2008 Tundra ? Not Yet Available ? 2005 to 2008 Sequoia ? Not Yet Available.
H0F-Technical In
Service Bulletin/Repair Instructions
Technical Instructions: Corrosion-Resistant Compound Application, Certain 2005 through 2010 Model Year Tacoma
ZH6-Dealer Lette
Service Bulletin/Repair Instructions
Dealer Letter: 2005-2010 Tacoma Frame Replacement is now available. On May 21, 2017, a settlement of claims in a class action lawsuit involving 2005 ? 2010 Toyota Tacoma, 2007-2008 Tundra, and 2005-2008 Sequoia vehicles regarding frame corrosion was approved. This finally approved class action settlement includes inspection of the customer?s frame, and if the frames meet or exceed the Rust Perforation Standard based upon the Court-ordered inspection criteria, the frame will be replaced at no cost to the customer. Toyota is currently preparing parts for frame replacement.
ZH6-Region Email
Service Bulletin/Repair Instructions
Region Email: 2005-2010 Tacoma Frame Replacement is now available. On May 21, 2017, a settlement of claims in a class action lawsuit involving 2005 ? 2010 Toyota Tacoma, 2007-2008 Tundra, and 2005-2008 Sequoia vehicles regarding frame corrosion was approved. This finally approved class action settlement includes inspection of the customer?s frame, and if the frames meet or exceed the Rust Perforation Standard based upon the Court-ordered inspection criteria, the frame will be replaced at no cost to the customer. Toyota is currently preparing parts for frame replacement.
ZH6-Region Lette
Service Bulletin/Repair Instructions
Region Letter: 2005-2010 Tacoma Frame Replacement is now available. On May 21, 2017, a settlement of claims in a class action lawsuit involving 2005 ? 2010 Toyota Tacoma, 2007-2008 Tundra, and 2005-2008 Sequoia vehicles regarding frame corrosion was approved. This finally approved class action settlement includes inspection of the customer?s frame, and if the frames meet or exceed the Rust Perforation Standard based upon the Court-ordered inspection criteria, the frame will be replaced at no cost to the customer. Toyota is currently preparing parts for frame replacement.
ZH6-Technical In
Service Bulletin/Repair Instructions
Technical Instructions: Corrosion-Resistant Compound Application, Certain 2005 through 2010 Modal Year Tacoma.
T-SB-0218-17_Rev
Service Bulletin/Repair Instructions
TSB: REVISION NOTICE July 20, 2017 Rev1: Applicability has been updated to exclude 2007 ? 2017 model year Avanza vehicles. Some hazardous material treatment and handling regulations at the state and local level define the pre-disposal deployment of airbag and pre-tensioner assemblies as hazardous material treatment. Hazardous material treatment may require special training, certification or licensing in certain areas. TMS recommends that dealership personnel carefully review and follow ALL local and state regulations, and where necessary, contract with Environmental Protection Agency (EPA) Licensed Hazardous Waste Transportation and Disposal facilities.
TI_Frame Inspect
Service Bulletin/Repair Instructions
Technical Instructions for Warranty Extension Program ZH6, ZH7, ZH8, and ZH9.
ZH6-POL17-09Rev
Service Bulletin/Repair Instructions
WARRANTY ENHANCEMENT PROGRAM (ZH6): WARRANTY EXTENSION FOR FRAME CORROSION ON CERTAIN 2005-2010 MY TACOMA VEHICLES
HR1_Dealer Lette
Service Bulletin/Repair Instructions
Dealer Letter: Toyota will be sending Safety Recall Follow-Up Notices to remind owners whose vehicles have not yet had campaign repairs completed.
HR1_Region Lette
Service Bulletin/Repair Instructions
Region Letter: Toyota will be sending Safety Recall Follow-Up Notices to remind owners whose vehicles have not yet had campaign repairs completed.
TSB018217
Service Bulletin/Repair Instructions
TSB: SUPERSESSION NOTICE The information contained in this bulletin supersedes SB No. T-SB-0101-11. Applicability has been updated to include 2016 ? 2017 model year vehicles. Service Bulletin No. T-SB-0101-11 is Obsolete and any printed versions should be discarded. Be sure to review the entire content of this bulletin before proceeding. When servicing interior electrical switches and components, please note the precautions in this bulletin to avoid damaging electrical components and switches. Many lubricants, cleaners, and automotive chemicals contain silicone or other compounds that may contaminate electrical contacts, and therefore increase electrical resistance and decrease switch performance. The use of any cleaners or fluids may increase the risk of further damage to electrical components.
T-SB-0012-13 Rev
Service Bulletin/Repair Instructions
TSB: OBSOLETE NOTICE: September 14, 2016: This bulletin is now obsolete. Please see T-SB-0134-16.
T-SB-0134-16
Service Bulletin/Repair Instructions
TSB: Supersession Notice. Flash reprogramming allows the ECU software to be updated without replacing the ECU. Flash calibration updates for specific vehicle models/ECUs are released as field-fix procedures described in individual Service Bulletins. This bulletin details the Techstream ECU flash reprogramming process and outlines use of the Technical Information System (TIS) and the Calibration Update Wizard (CUW). Flash calibration updates can only be applied to the vehicle/ECU combination for which they are intended. ECUs have internal security that will not allow them to be programmed with another ECU?s information.
Safety Recall an
Service Bulletin/Repair Instructions
Update on Technician Certification Requirements.
E0D_Region Notic
Service Bulletin/Repair Instructions
Region Notice: Due to the expiration of LSC E0D, on April 1, 2016 all VINs were marked expired in TIS. As a result claims submitted after this date will automatically be placed in ?Not Approved? status in the CPS warranty system.
ESD_Region Notic
Service Bulletin/Repair Instructions
Region Notice: Due to the expiration of LSC ESD, on April 1, 2016 all VINs were marked expired in TIS. As a result claims submitted after this date will automatically be placed in ?Not Approved? status in the CPS warranty system.
E0D ESD_Dealer D
Service Bulletin/Repair Instructions
Dealer Daily: ? Toyota has received reports that certain 2005 through 2008 model year Tacoma vehicles operated in specific cold climate areas (Cold Climate States) with high road salt usage may exhibit more-than-normal corrosion to the vehicle?s frame. ? Toyota investigated these reports and determined that the frames in some vehicles may not have corrosion-resistant protection sufficient for use in these areas. ? This combined with prolonged exposure to road salts and other environmental factors may contribute to the development of more-than-normal rust in the frame of some vehicles. ? This condition is unrelated to and separate from normal surface rust which is commonly found on metallic surfaces after some years of usage and/or exposure to the environment.
E0D_Dealer Lette
Service Bulletin/Repair Instructions
Dealer Letter: The dealer letter has been updated to include details of the frame registration and credit program that has been added to Limited Service Campaigns E0D and ESD.
ESD_Dealer Lette
Service Bulletin/Repair Instructions
Dealer Daily: ? Toyota has received reports that certain 2005 through 2008 model year Tacoma vehicles operated in specific cold climate areas (Cold Climate States) with high road salt usage may exhibit more-than-normal corrosion to the vehicle?s frame. ? Toyota investigated these reports and determined that the frames in some vehicles may not have corrosion-resistant protection sufficient for use in these areas. ? This combined with prolonged exposure to road salts and other environmental factors may contribute to the development of more-than-normal rust in the frame of some vehicles. ? This condition is unrelated to and separate from normal surface rust which is commonly found on metallic surfaces after some years of usage and/or exposure to the environment.
E0D ESD 2/29
Service Bulletin/Repair Instructions
DEALER LETTER: FRAME REPLACEMENT CUSTOMER VEHICLES THAT QUALIFY FOR FRAME REPLACEMENT UNDER E0D/ESD MUST HAVE THEIR VEHICLE INSPECTED ON OR BEFORE MARCH 31, 2016. FRAME AND ANCILLARY PARTS ORDERS MUST BE SUBMITTED NO LATER THAN TUESDAY, APRIL 5TH, 2016 FOLLOWING THE EXPIRATION DATE. CRC APPLICATION E0D ONLY LAST DAY OF CRC APPLICATION IS MARCH 31, 2016, REGARDLESS OF VEHICLE INSPECTION DATE TAKING PLACE ON OR BEFORE THE EXPIRATION DATE. CLAIMS WILL NOT BE PAID FOR ANY VEHICLE SPRAYED AFTER MARCH, 31 2016 AND ARE NOT ELIGIBLE FOR GOODWILL. THE LAST DAY FOR CRC KIT ORDERS IS MARCH 29, 2016 AND AS A REMINDER THE KITS ARE NOT RETURNABLE. CRC KIT ORDERS ARE SHIPPED GROUND AND TAKE APPROXIMATELY 3 DAYS FOR DELIVERY; PLEASE TAKE THIS INTO CONSIDERATION WHEN ORDERING TO ENSURE THEY ARRIVE PRIOR TO THE EXPIRATION DATE. ORDERS SHOULD ALSO NOT EXCEED CAMPAIGN APPOINTMENTS.
E0D ESD 2/10
Service Bulletin/Repair Instructions
QUICK REFERENCE GUIDE: FRAME REPLACEMENT ALL FRAMES MUST BE INSPECTED ON OR BEFORE MARCH 31, 2016 IN ORDER TO QUALIFY FOR FRAME REPLACEMENT. VEHICLES INSPECTED AFTER THIS DATE WILL NOT BE COVERED UNDER THE LIMITED SERVICE CAMPAIGN. CRC APPLICATION (COLD STATE ONLY) MARCH 31, 2016 IS THE LAST DAY OF CRC APPLICATION, REGARDLESS OF VEHICLE INSPECTION DATE TAKING PLACE ON OR BEFORE THE EXPIRATION DATE.
E0D ESD_Quick Re
Service Bulletin/Repair Instructions
Quick Reference Guide: Frame Replacement All frames must be inspected on or before March 31, 2016 in order to qualify for frame replacement. Vehicles inspected after this date will not be covered under the Limited Service Campaign. CRC Application (COLD STATE ONLY) March 31, 2016 is the last day of CRC application, regardless of vehicle inspection date taking place on or before the expiration date.
E0D ESD 2/1
Service Bulletin/Repair Instructions
DEALER LETTER: FRAME REPLACEMENT CUSTOMER VEHICLES THAT QUALIFY FOR FRAME REPLACEMENT UNDER E0D/ESD MUST HAVE THEIR VEHICLE INSPECTED ON OR BEFORE MARCH 31, 2016. FRAME AND ANCILLARY PARTS ORDERS MUST BE SUBMITTED NO LATER THAN TUESDAY, APRIL 5TH, 2016 FOLLOWING THE EXPIRATION DATE. CRC APPLICATION E0D ONLY LAST DAY OF CRC APPLICATION IS MARCH 31, 2016, REGARDLESS OF VEHICLE INSPECTION DATE TAKING PLACE ON OR BEFORE THE EXPIRATION DATE. CLAIMS WILL NOT BE PAID FOR ANY VEHICLE SPRAYED AFTER MARCH, 31 2016 AND ARE NOT ELIGIBLE FOR GOODWILL. THE LAST DAY FOR CRC KIT ORDERS IS MARCH 29, 2016 AND AS A REMINDER THE KITS ARE NOT RETURNABLE. CRC KIT ORDERS ARE SHIPPED GROUND AND TAKE APPROXIMATELY 3 DAYS FOR DELIVERY; PLEASE TAKE THIS INTO CONSIDERATION WHEN ORDERING TO ENSURE THEY ARRIVE PRIOR TO THE EXPIRATION DATE. ORDERS SHOULD ALSO NOT EXCEED CAMPAIGN APPOINTMENTS.
GR1_DEALER LETTE
Service Bulletin/Repair Instructions
DEALER LETTER: SAFETY RECALL COMPLETION IS IMPORTANT NOT ONLY IN SATISFYING GOVERNMENT REQUIREMENTS, BUT ALSO IS AN INTEGRAL PART OF OUR COMMITMENT TO MEET CUSTOMER EXPECTATIONS OF TOYOTA PRODUCTS. TOYOTA WILL BE SENDING SAFETY RECALL FOLLOW-UP NOTICES TO REMIND OWNERS WHOSE VEHICLES HAVE NOT YET HAD CAMPAIGN REPAIRS COMPLETED. WE REQUEST YOUR ASSISTANCE IN COMPLETING THE APPLICABLE CAMPAIGN REPAIRS AS OWNERS RECEIVE THE FOLLOW-UP NOTICE AND CONTACT YOUR DEALERSHIP. PLEASE NOTE THE FOLLOW-UP ACTIVITY MAY CAUSE AN INCREASE IN YOUR CURRENT CAMPAIGN OWNER APPOINTMENTS. TOYOTA WILL CONTINUE WITH ADDITIONAL FOLLOW-UP ACTIVITIES IN THE MONTHS TO COME. PLEASE TAKE THIS INTO CONSIDERATION WHEN ANALYZING YOUR MANPOWER REQUIREMENTS.
GR1_Dealer Lette
Service Bulletin/Repair Instructions
Dealer Letter: Safety Recall completion is important not only in satisfying government requirements, but also is an integral part of our commitment to meet customer expectations of Toyota products. Toyota will be sending Safety Recall Follow-Up Notices to remind owners whose vehicles have not yet had campaign repairs completed. We request your assistance in completing the applicable campaign repairs as owners receive the Follow-Up Notice and contact your dealership. Please note the follow-up activity may cause an increase in your current campaign owner appointments. Toyota will continue with additional follow-up activities in the months to come. Please take this into consideration when analyzing your manpower requirements.
TC-16-001
Service Bulletin/Repair Instructions
Region Letter: Toyota will be sending Safety Recall Follow-Up Notices to remind owners whose vehicles have not yet had campaign repairs completed. Please note the following information for Regional and PD associates.
T-TT-0381-16
Service Bulletin/Repair Instructions
Tech Tip: Some customers may experience difficulty programming HomeLink.
E0D ESD_D 11/30
Service Bulletin/Repair Instructions
DL: LIMITED SERVICE CAMPAIGN COMPLETION IS IMPORTANT AND IS AN INTEGRAL PART OF OUR COMMITMENT TO MEET CUSTOMER EXPECTATIONS OF TOYOTA PRODUCTS. TOYOTA WILL BE SENDING LIMITED SERVICE CAMPAIGN FOLLOW-UP NOTICES TO REMIND OWNERS WHOSE VEHICLES HAVE NOT YET HAD CAMPAIGN REPAIRS COMPLETED. WE REQUEST YOUR ASSISTANCE IN COMPLETING THE APPLICABLE CAMPAIGN REPAIRS AS OWNERS RECEIVE THE FOLLOW-UP NOTICE AND CONTACT YOUR DEALERSHIP. PLEASE NOT THE FOLLOW-UP ACTIVITY MAY CAUSE AN INCREASE IN YOUR CURRENT CAMPAIGN OWNER APPOINTMENTS. TOYOTA WILL CONTINUE WITH ADDITIONAL FOLLOW-UP ACTIVITIES IN THE MONTHS TO COME. PLEASE TAKE THIS INTO CONSIDERATION WHEN ANALYZING YOUR MANPOWER REQUIREMENTS.
E0D ESD_Dealer L
Service Bulletin/Repair Instructions
DL: Limited Service Campaign completion is important and is an integral part of our commitment to meet customer expectations of Toyota products. Toyota will be sending Limited Service Campaign Follow-Up Notices to remind owners whose vehicles have not yet had campaign repairs completed. We request your assistance in completing the applicable campaign repairs as owners receive the Follow-Up Notice and contact your dealership. Please not the follow-up activity may cause an increase in your current campaign owner appointments. Toyota will continue with additional follow-up activities in the months to come. Please take this into consideration when analyzing your manpower requirements.
E0D ESD_R 11/30
Service Bulletin/Repair Instructions
RL: TOYOTA WILL BE SENDING LIMITED SERVICE CAMPAIGN FOLLOW-UP NOTICES TO REMIND OWNERS WHOSE VEHICLES HAVE NOT YET HAD CAMPAIGN REPAIRS COMPLETED.
E0D ESD_Region L
Service Bulletin/Repair Instructions
RL: Toyota will be sending Limited Service Campaign Follow-Up Notices to remind owners whose vehicles have not yet had campaign repairs completed.
T-TT-0362-15
Service Bulletin/Repair Instructions
TT: The vehicle may be difficult to start or have an abnormally low or rough idle after the battery has been disconnected or power to the Engine ECM has been interrupted.
T-TT-0086-11
Service Bulletin/Repair Instructions
TechTip: Condition - The vehicle may be difficult to start or have an abnormally low or rough idle after the battery has been disconnected or power to the Engine ECM has been interrupted.
T-SB-0043-14 Rev
Service Bulletin/Repair Instructions
TSB: The Immobilizer and Smart Key Reset is a feature that allows the registration of new keys when all master keys are lost. Once the system is reset, all previously registered keys will be erased. Follow the procedures in this bulletin to reset a vehicle Immobilizer or Smart Key system. NOTE: There are new security provisions required to obtain a Reset Pass-Code. It is critical that the instructions for this new process are reviewed BEFORE attempting to get a Pass-Code in the new system.
T-SB-0026-15
Service Bulletin/Repair Instructions
TSB: Some 2004 - 2015 model year Tacoma, FJ Cruiser, and 4Runner vehicles may exhibit a cyclical grinding or groaning noise coming from the front differential in 2WD that goes away when operated in 4WD. This noise can be addressed by replacing the needle bearing on the left side of the front differential. Refer to the Repair Procedure for Needle Bearing Roller replacement instructions.
T-SB-0083-13 Rev
Service Bulletin/Repair Instructions
TSB: The procedure in this bulletin is a general guideline on how to properly diagnose the air conditioning system after a component failure. Refer to the applicable Repair Manual for vehicle specific repair procedures and parts.
E0D_ESD_LSC_Rent
Service Bulletin/Repair Instructions
EC: Rental vehicle opcodes have been updated for Limited Service Campaigns E0D and ESD. Refer to the updated dealer letter that has been posted to TIS.
LSC(ESD
Service Bulletin/Repair Instructions
THIS TSB CONTAINS DOCUMENT OWNER LETTER. SEE DOCUMENT SEARCH BUTTON. TOYOTA TACOMA 2005-2008: BULLETIN INFORMATION REGARDING CUSTOMER COMPLAINTS OF VEHICLES OPERATING IN COLD WEATHER WITH HIGH ROAD SALT USAGE MAY EXPERIENCE CORROSION TO THE FRAME. *LJ
T-SB-0101-11 Rev
Service Bulletin/Repair Instructions
TSB: When servicing interior electrical switches and components, please note the precautions in this bulletin to avoid damaging electrical components and switches. Many lubricants, cleaners, and automotive chemicals contain silicone or other compounds that may contaminate electrical contacts, and therefore increase electrical resistance and decrease switch performance. The use of any cleaners or fluids may increase the risk of further damage to electrical components.
T-SB-0057-13 Rev
Service Bulletin/Repair Instructions
TSB: Some 2005 - 2013 model year Tacoma vehicles equipped with a 5-speed automatic transmission may exhibit a whine noise from the rear differential between 50 - 60 mph (80 - 97 km/h). Use the following Repair Procedure to address this condition. NOTE-This bulletin does NOT apply to Limited Slip Differential (LSD) or locking type rear differentials.
FR1_Remail_Deale
Service Bulletin/Repair Instructions
DL: Safety Recall completion is important not only in satisfying government requirements but also as an integral part of our commitment to meet customer expectations of Toyota products. Toyota will be sending Safety Recall Follow-Up Notices to remind owners whose vehicles have not yet had recall campaign repairs completed. We request your dealer's assistance in completing the applicable recall campaign repairs as owners receive the Safety Recall Follow-Up Notices and contact them. Please note the follow-up activity may cause an increase in current recall campaign owner appointments. Toyota will continue with additional follow-up activities in the months to come.
FR1_Remail_Regio
Service Bulletin/Repair Instructions
RL: Toyota will be sending Safety Recall Follow-Up Notices to remind owners whose vehicles have not yet had campaign repairs completed. Please note the following information for Regional and PD associates.
ESD_Region Lette
Service Bulletin/Repair Instructions
Region Letter: In 2014, Toyota announced and rolled out a Limited Service Campaign (LSC E0D) for certain 2005-2008 model year Toyota Tacoma vehicles currently registered in specific cold climate areas with high road salt usage (Cold Climate States). Toyota is now announcing LSC ESD to also support owners of vehicles that are not registered in Cold Climate States but believe their vehicle has been operated in cold climate regions where high road salt is frequently used and/or customers with concerns their vehicle's frame has more-than-normal corrosion.
TC-15-009
Service Bulletin/Repair Instructions
Region Letter: In 2014, Toyota announced and rolled out a Limited Service Campaign (LSC E0D) for certain 2005-2008 model year Toyota Tacoma vehicles currently registered in specific cold climate areas with high road salt usage (Cold Climate States). Toyota is now announcing LSC ESD to also support owners of vehicles that are not registered in Cold Climate States but believe their vehicle has been operated in cold climate regions where high road salt is frequently used and/or customers with concerns their vehicle's frame has more-than-normal corrosion.
TC15-009
Service Bulletin/Repair Instructions
TOYOTA 2005-2008 TACOMA: THIS CONTAINS AN OWNER NOTIFICATION LETTER. SELECT DOCUMENT SEARCH BUTTON BELOW. CERTAIN REPORTS RECEIVED REGARDING CORROSION TO VEHICLES FRAME DUE TO COLD CLIMATE. *LJ
T-SB-0040-08
Service Bulletin/Repair Instructions
TSB: On some vehicles, when Rapgard is removed, the paint may have a stained appearance. These stains appear to be under the clear coat (repainting this area is not necessary). The stain patterns are usually under wrinkles in the Rapgard. These wrinkles sometimes trap water and cause the paint to stain from the trapped moisture, especially on horizontal surfaces, such as the hood, roof, and trunk. Stains can be removed by heating the stained surface to remove the trapped moisture.
E0D_Dealer Daily
Service Bulletin/Repair Instructions
Dealer Daily: Due to limited availability of 05 - 08 Tacoma frame activity parts, Toyota will be implementing a new ordering process for all future frame and ancillary part orders. Beginning January 28th, 2015 it will be mandatory for all dealers to order the frame and all required ancillary parts for each vehicle using the same order reference number. Many ancillary parts will be placed on MAC due to backorder condition and will be released once the frame is ready to be shipped to the dealership. There will be no additional requirements by the dealership for the release of the MAC parts.
GR1_REGION LETTE
Service Bulletin/Repair Instructions
REGION LETTER: TOYOTA WILL BE SENDING SAFETY RECALL FOLLOW-UP NOTICES TO REMIND OWNERS WHOSE VEHICLES HAVE NOT YET HAD CAMPAIGN REPAIRS COMPLETED. PLEASE NOTE THE FOLLOWING INFORMATION FOR REGIONAL AND PD ASSOCIATES.
T-SB-0012-13 REV
Service Bulletin/Repair Instructions
TSB: FLASH REPROGRAMMING ALLOWS THE ECU SOFTWARE TO BE UPDATED WITHOUT REPLACING THE ECU. FLASH CALIBRATION UPDATES FOR SPECIFIC VEHICLE MODELS/ECUS ARE RELEASED AS FIELD-FIX PROCEDURES DESCRIBED IN INDIVIDUAL SERVICE BULLETINS. THIS BULLETIN DETAILS THE TECHSTREAM ECU FLASH REPROGRAMMING PROCESS AND OUTLINES USE OF THE TECHNICAL INFORMATION SYSTEM (TIS) AND THE CALIBRATION UPDATE WIZARD (CUW). FLASH CALIBRATION UPDATES CAN ONLY BE APPLIED TO THE VEHICLE/ECU COMBINATION FOR WHICH THEY ARE INTENDED. ECUS HAVE INTERNAL SECURITY THAT WILL NOT ALLOW THEM TO BE PROGRAMMED WITH ANOTHER ECUS INFORMATION.
TSB-0012-13 Rev2
Service Bulletin/Repair Instructions
TSB: Flash reprogramming allows the ECU software to be updated without replacing the ECU. Flash calibration updates for specific vehicle models/ECUs are released as field-fix procedures described in individual Service Bulletins. This bulletin details the Techstream ECU flash reprogramming process and outlines use of the Technical Information System (TIS) and the Calibration Update Wizard (CUW). Flash calibration updates can only be applied to the vehicle/ECU combination for which they are intended. ECUs have internal security that will not allow them to be programmed with another ECU?s information.
E0D_LSC_CAT Deal
Service Bulletin/Repair Instructions
Region Letter: Condition: ? Toyota has received reports that certain 2005 through 2008 model year Tacoma vehicles operated in specific cold climate areas (Cold Climate States) with high road salt usage may exhibit more-than-normal corrosion to the vehicle's frame. ? Toyota investigated these reports and determined that the frames in some vehicles may not have corrosion-resistant protection sufficient for use in these areas. ? This combined with prolonged exposure to road salts and other environmental factors, may contribute to the development of more-than-normal rust in the frame of some vehicles. ? This condition is unrelated to and separate from normal surface rust which is commonly found on metallic surfaces after some years of usage and/or exposure to the environment.
E0D_LSC_CAT Regi
Service Bulletin/Repair Instructions
Region Letter: Condition: ? Toyota has received reports that certain 2005 through 2008 model year Tacoma vehicles operated in specific cold climate areas (Cold Climate States) with high road salt usage may exhibit more-than-normal corrosion to the vehicle's frame. ? Toyota investigated these reports and determined that the frames in some vehicles may not have corrosion-resistant protection sufficient for use in these areas. ? This combined with prolonged exposure to road salts and other environmental factors, may contribute to the development of more-than-normal rust in the frame of some vehicles. ? This condition is unrelated to and separate from normal surface rust which is commonly found on metallic surfaces after some years of usage and/or exposure to the environment.
TC 14-039
Service Bulletin/Repair Instructions
TOYOTA: SEE DOCUMENT SEARCH BUTTON FOR OWNER LETTER. DUE TO SIGNIFICANT RUST, FROM ROAD SALT, A LIMITED SERVICE CAMPAIGN HAS BEEN ISSUED REGARDING CORROSION RESISTANT COMPOUNDS (CRC) APPLICATION, TO KEY AREAS OF FRAME ASSEMBLY. MODEL 2005-2008 TACOMA. *PE
TC14-039
Service Bulletin/Repair Instructions
TOYOTA TACOMA 2005-2008: CORROSION- RESISTANT COMPOUND TO FRAME OF SOME TRUCKS TOREVENT RUST. SEE DOCUMENT SEARCH BUTTON FOR OWNERS LETTER. *LJ
ER10_Remail_Deal
Service Bulletin/Repair Instructions
Dealer Letter: Safety Recall completion is important not only in satisfying government requirements but also is an integral part of our commitment to meet customer expectations of Toyota products. Toyota will be sending Safety Recall Follow-Up Notices to remind owners whose vehicles have not yet had campaign repairs completed. We request your assistance in completing the applicable campaign repairs as owners receive the Follow-Up Notice and contact your dealership. Please note the follow-up activity may cause an increase in your current campaign owner appointments. Toyota will continue with additional follow-up activities in the months to come. Please take this into consideration when analyzing your manpower requirements.
ER10_Remail_Regi
Service Bulletin/Repair Instructions
Region Letter: Toyota will be sending Safety Recall Follow-Up Notices to remind owners whose vehicles have not yet had campaign repairs completed.
T-SB-0006-11 Rev
Service Bulletin/Repair Instructions
TSB: World Standard (WS) Automatic Transmission Fluid (ATF) was introduced to reduce maintenance costs and increase the mileage between scheduled maintenance checks. Here are some important tips when working with ATF-WS in Toyota vehicles requiring it's use.
T-SB-0014-11 Rev
Service Bulletin/Repair Instructions
TSB: The purpose of this service bulletin is to provide information regarding the installation of the correct torque converter bolts during automatic transmission/transaxle assembly replacement. Incorrect torque converter bolts or missing washers can cause damage to the torque converter assembly.
T-SB-0049-11 Rev
Service Bulletin/Repair Instructions
TSB: The purpose of this bulletin is to provide information regarding transmission and/or park neutral position switch installation. If the manual shift lever is rotated prior to installing the park neutral position switch, the detent spring may become detached from the manual shift lever.
T-SB-0260-08 Rev
Service Bulletin/Repair Instructions
TSB: The purpose of this bulletin is to assist in the identification and location of serial numbers on 2006 -2014 model year remanufactured automatic transmissions.
T-SB-0044-14 Rev
Service Bulletin/Repair Instructions
TSB: Some 2012 - 2014 model year Tacoma vehicles equipped with 1GR-FE engines may exhibit spark knock (detonation) during light acceleration and/or uphill in hot weather (80°F or higher). The Engine Control module/ECM (SAE term: Powertrain Control Module/PCM) logic has been modified to reduce the possibility of this condition occurring.
T-SB-0134-14
Service Bulletin/Repair Instructions
TSB: The purpose of this bulletin is to provide precautions to follow when installing an automatic transmission/transaxle assembly to avoid MIL "ON" shifting issues and/or transmission damage. Use the information in this bulletin when installing an automatic transmission/transaxle assembly.
T-SB-0200-08 Rev
Service Bulletin/Repair Instructions
TSB: The purpose of this bulletin is to assist in the identification and location of serial numbers on 2006 - 2014 model year automatic transmissions.
9-29-14
Service Bulletin/Repair Instructions
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
E0D_LSC_NY Deale
Service Bulletin/Repair Instructions
Dealer Letter: Condition: Toyota has received reports that certain 2005 through 2008 model year Tacoma vehicles operated in specific cold climate areas (Cold Climate States) with high road salt usage may exhibit more-than-normal corrosion to the vehicle's frame. ? Toyota investigated these reports and determined that the frames in some vehicles may not have corrosion-resistant protection sufficient for use in these areas. ? This combined with prolonged exposure to road salts and other environmental factors, may contribute to the development of more-than-normal rust in the frame of some vehicles. ? This condition is unrelated to and separate from normal surface rust which is commonly found on metallic surfaces after some years of usage and/or exposure to the environment.
E0D_LSC_NY Regio
Service Bulletin/Repair Instructions
Region Letter: Condition: Toyota has received reports that certain 2005 through 2008 model year Tacoma vehicles operated in specific cold climate areas (Cold Climate States) with high road salt usage may exhibit more-than-normal corrosion to the vehicle's frame. ? Toyota investigated these reports and determined that the frames in some vehicles may not have corrosion-resistant protection sufficient for use in these areas. ? This combined with prolonged exposure to road salts and other environmental factors, may contribute to the development of more-than-normal rust in the frame of some vehicles. ? This condition is unrelated to and separate from normal surface rust which is commonly found on metallic surfaces after some years of usage and/or exposure to the environment.
TC-14-039
Service Bulletin/Repair Instructions
TOYOTA: SEE DOCUMENT SEARCH BUTTON FOR OWNER LETTER. DUE TO SIGNIFICANT RUST PERFORATION AND BASED UPON INSPECTION CRITERIA, A LIMITED SERVICE CAMPAIGN HAS BEEN ISSUED REGARDING THE APPLICATION OF CORROSION RESISTANT COMPOUNDS (CRC) TO KEY AREAS OF FRAME ASSEMBLY. MODEL 2005-2008 TACOMA. *PE
T-SB-0186-12 Rev
Service Bulletin/Repair Instructions
TSB: Some 2005 - 2014 model year Tacoma vehicles may exhibit a squeak or creak noise from the clutch pedal when it is depressed or released. Changes have been made to the clutch pedal and clutch master cylinder assembly to address this condition.
E0D_LSC_Chicago
Service Bulletin/Repair Instructions
Dealer Letter: Condition-? Toyota has received reports that certain 2005 through 2008 model year Tacoma vehicles operated in specific cold climate areas (Cold Climate States) with high road salt usage may exhibit more-than-normal corrosion to the vehicle's frame. ? Toyota investigated these reports and determined that the frames in some vehicles may not have corrosion resistant protection sufficient for use in these areas. ? This combined with prolonged exposure to road salts and other environmental factors, may contribute to the development of more-than-normal rust in the frame of some vehicles. ? This condition is unrelated to and separate from normal surface rust which is commonly found on metallic surfaces after some years of usage and/or exposure to the environment.
SB-TC-14-039
Service Bulletin/Repair Instructions
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
T-SB-0016-13 Rev
Service Bulletin/Repair Instructions
TSB: Some 4WD 2005 - 2013 model year Tacoma vehicles equipped with an automatic transmission may exhibit a clunk/thunk noise from the rear of the vehicle or a "bump-from-behind" sensation just before a stop or when accelerating from a stop. Improvements have been implemented on the rear propeller shaft (driveshaft) to reduce this condition.
T-SB-0250-12 Rev
Service Bulletin/Repair Instructions
TSB: Some 2WD 2005 - 2013 model year Tacoma vehicles equipped with an automatic transmission may exhibit a clunk/thunk noise from the rear of the vehicle or a "bump-from-behind" sensation just before a stop or when accelerating from a stop. Improvements have been implemented on the rear propeller shaft (driveshaft). Follow the Repair Procedure in this bulletin to improve this condition.
T-SB-0008-14
Service Bulletin/Repair Instructions
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
T-SB-0008-14 Rev
Service Bulletin/Repair Instructions
TSB: Some 2005 ? 2014 model year Tacoma vehicles equipped with 1GR-FE engine (PreRunner and 4WD) and automatic or 6-speed manual transmission may exhibit a vibration felt in the seat, floorboard, and steering wheel between 15 ? 25 mph caused by a second order drivetrain vibration under acceleration. The following Repair Procedure may improve this condition.
TC-14-025
Service Bulletin/Repair Instructions
TOYOTA: SEE DOCUMENT SEARCH BUTTON FOR OWNER LETTER. THE HEADLAMP ASSEMBLY INNER LENS DISTORTION/BUBBLING, AND POSSIBLE CRACKED OR SEPARATED INNER LENS, HAVE AN EXTENDED WARRANTY COVERAGE. MODEL 2005-2011 TACOMA. *PE
ZTZ_WEP_Dealer L
Service Bulletin/Repair Instructions
Dealer Letter: In our continuing efforts to ensure the best in customer satisfaction, Toyota is announcing a Warranty Enhancement Program to extend the warranty coverage for the Headlamp Assembly on 2005-2011 model year Tacoma vehicles. In these vehicles, Toyota has received some reports where the inner Daytime Running Light/Turn Signal lens becomes distorted and bubbled in appearance, in addition the inner lens may appear cracked or separated. Important Note: This condition should not be confused with normal yellow-orange color that occurs over time as the inner lens ages. Additionally, this program does not address conditions related to the outer headlamp lens. Although the Headlamp Assembly is covered by Toyota?s New Vehicle Limited Warranty for 3 years or 36,000 miles (whichever occurs first), we at Toyota care about the customers? ownership experience. Toyota is now extending the warranty coverage for the Headlamp Assembly for the condition described in the covered vehicles. Please see the Warranty Enhancement Program Details for additional information.
ZTZ_WEP_Region L
Service Bulletin/Repair Instructions
Region Letter: In our continuing efforts to ensure the best in customer satisfaction, Toyota is announcing a Warranty Enhancement Program to extend the warranty coverage for the Headlamp Assembly on 2005-2011 model year Tacoma vehicles. In these vehicles, Toyota has received some reports where the inner Daytime Running Light/Turn Signal lens becomes distorted and bubbled in appearance, in addition the inner lens may appear cracked or separated. Important Note: This condition should not be confused with normal yellow-orange color that occurs over time as the inner lens ages. Additionally, this program does not address conditions related to the outer headlamp lens. Although the Headlamp Assembly is covered by Toyota?s New Vehicle Limited Warranty for 3 years or 36,000 miles (whichever occurs first), we at Toyota care about the customers? ownership experience. Toyota is now extending the warranty coverage for the Headlamp Assembly for the condition described in the covered vehicles. Please see the Warranty Enhancement Program Details for additional information.
E0D_LSC_CIN Deal
Service Bulletin/Repair Instructions
Dealer Letter: ? Toyota has received reports that certain 2005 through 2008 model year Tacoma vehicles operated in specific cold climate areas (Cold Climate States) with high road salt usage may exhibit more-than-normal corrosion to the vehicle?s frame. ? Toyota investigated these reports and determined that the frames in some vehicles may not have corrosion-resistant protection sufficient for use in these areas. ? This combined with prolonged exposure to road salts and other environmental factors, may contribute to the development of more-than-normal rust in the frame of some vehicles. ? This condition is unrelated to and separate from normal surface rust which is commonly found on metallic surfaces after some years of usage and/or exposure to the environment.
E0D_LSC_CIN Regi
Service Bulletin/Repair Instructions
Region Letter: ? Toyota has received reports that certain 2005 through 2008 model year Tacoma vehicles operated in specific cold climate areas (Cold Climate States) with high road salt usage may exhibit more-than-normal corrosion to the vehicle?s frame. ? Toyota investigated these reports and determined that the frames in some vehicles may not have corrosion-resistant protection sufficient for use in these areas. ? This combined with prolonged exposure to road salts and other environmental factors, may contribute to the development of more-than-normal rust in the frame of some vehicles. ? This condition is unrelated to and separate from normal surface rust which is commonly found on metallic surfaces after some years of usage and/or exposure to the environment.
TC-14-013
Service Bulletin/Repair Instructions
TOYOTA: SEE DOCUMENT SEARCH BUTTON FOR OWNER LETTER. INFORMATION PROVIDED REGARDING THE CORROSION RESISTANT COMPOUND (CRC) APPLICATION FOR SOME VEHICLES FRAMES DUE TO USAGE OF HIGH ROAD SALT, IN CERTAIN STATES. MODEL 2005-2008 TACOMA. *PE UPDATED 9/2/14. *PE
T-SB-0037-14
Service Bulletin/Repair Instructions
TSB: Some 2005 ? 2014 model year Tacoma vehicles used in severe off-road service conditions may exhibit a cracked Horn Mounting Bracket. Use the procedure in this bulletin to address this condition.
TSB-0016-13 REV1
Service Bulletin/Repair Instructions
TOYOTA: A SENSATION OF A BUMP FROM BEHIND OR EXHIBITING A CLUNK OR THUNK NOISE COMING FROM REAR JUST AS ACCELERATING OR COMING TO A STOP. MODEL 2005-2013 TACOMA. *PE
TSB-0250-12
Service Bulletin/Repair Instructions
TOYOTA: JUST BEFORE COMING TO A STOP OR ACCELERATING FROM A STOP WOULD EXPERIENCE A BUMP FROM BEHIND SENSATION OR HEAR A THUNKING OR CLUNKING NOISE FROM REAR OF VEHICLE. INFORMATION ON REPAIR PROCEDURE ON REAR PROPELLER SHAFT (DRIVESHAFT) HAS BEEN IMPLEMENTED. MODEL 2005-2012 TACOMA. *PE UPDATED 8/29/14. *PE
ER5_Remail_Deale
Service Bulletin/Repair Instructions
Dealer Letter: Toyota will be sending Safety Recall Follow-Up Notices to remind owners whose vehicles have not yet had campaign repairs completed for: C0B, C0R, D0C, D0G.
ER5_Remail_Regio
Service Bulletin/Repair Instructions
Region Letter: Toyota will be sending Safety Recall Follow-Up Notices to remind owners whose vehicles have not yet had campaign repairs completed for: C0B, C0R, D0C, D0G.
LSC E0D - CAT De
Service Bulletin/Repair Instructions
Dealer Letter: * Toyota has received reports that certain 2005 through 2008 model year Tacoma vehicles operated in specific cold climate areas (Cold Climate States) with high road salt usage may exhibit more-than-normal corrosion to the vehicle's frame. * Toyota investigated these reports and determined that the frames in some vehicles may not have corrosion-resistant protection sufficient for use in these areas. * This combined with prolonged exposure to road salts and other environmental factors, may contribute to the development of more-than-normal rust in the frame of some vehicles. * This condition is unrelated to and separate from normal surface rust which is commonly found on metallic surfaces after some years of usage and/or exposure to the environment.
LSC E0D - CAT Re
Service Bulletin/Repair Instructions
Region Letter: ? Toyota has received reports that certain 2005 through 2008 model year Tacoma vehicles operated in specific cold climate areas (Cold Climate States) with high road salt usage may exhibit more-than-normal corrosion to the vehicle?s frame. ? Toyota investigated these reports and determined that the frames in some vehicles may not have corrosion-resistant protection sufficient for use in these areas. ? This combined with prolonged exposure to road salts and other environmental factors, may contribute to the development of more-than-normal rust in the frame of some vehicles. ? This condition is unrelated to and separate from normal surface rust which is commonly found on metallic surfaces after some years of usage and/or exposure to the environment.
T-TT-0010-10 Rev
Service Bulletin/Repair Instructions
Tech Tip: Low battery voltage can contribute to a MIL "ON" condition for P0335 (Crankshaft Position Sensor Circuit) and/or P0340 (Camshaft Position Sensor Circuit) due to inconsistent rotational speed of the engine's crankshaft.
T-SB-0129-11 Rev
Service Bulletin/Repair Instructions
Some 2005 ? 2011 model year Tacoma vehicles may experience a condition where the inner Daytime Running Light (DRL)/turn signal lens becomes distorted and bubbled in appearance. In addition, the inner lens may appear cracked or separated. Updated Headlamp Assemblies have been developed to address this condition. The updated Headlamp Assemblies have cosmetic changes, so it is recommended to replace both the left and right assemblies together.
T-TT-0132-11
Service Bulletin/Repair Instructions
A key part to maintain the proper function and safe operation of the vehicle's braking system is to perform a visual inspection when installing brake pads, calipers, and discs. The following recommendations are intended to provide general tips for the inspection and/or installation of Toyota Complete Maintenance Care (TCMC) front brake pads and discs. Always refer to the model specific Repair manual and TIS publications for specific repair instructions.
T-SB-0187-12 Rev
Service Bulletin/Repair Instructions
Toyota vehicles are equipped with either conventional or run-flat tires. Sometimes punctures may occur as a result of contact with road debris or other hazards. If a puncture occurs, it may be possible to repair the tire and return it to service. With a conventional tire it is not possible to drive for an extended amount of time with the tire at low pressures as damage to the tire may occur. With run-flat tires, due to reinforced sidewalls, it is possible to drive for up to 100 miles (160 km) at speeds less than 55 mph (90 km/h) with little or no damage to the tire.
T-TT-0213-13
Service Bulletin/Repair Instructions
Toyota vehicles are equipped with Supplemental Restraint Systems (SRS), including various airbags and in some models, seat belt pre-tensioners, to help reduce the risk of injury in a collision. If a customer expresses any concerns that the SRS airbags or pre-tensioner devices did not perform as expected (including an unintended deployment event), please follow the steps in the recommendations section below.
T-SB-0185-13
Service Bulletin/Repair Instructions
The following procedures are recommended during routine maintenance or in the event of a customer concern for wiper performance.
TS-BO030-01 Obso
Service Bulletin/Repair Instructions
This bulletin is now obsolete. Please see T-SB-0185-13.
T-SB-0122-11 Rev
Service Bulletin/Repair Instructions
Beginning in 1998, Toyota introduced side airbags as optional equipment. Toyota does NOT recommend replacement of original seat covers with non-Toyota leather or other seat cover materials on vehicles due to the following: Seat covers NOT recommended by Toyota may affect side airbag performance, in general or in part, during an accident. Modifications that negatively affect side airbag performance can result in severe occupant injuries. Seat covers are an integral part of this safety system. Replacing fabric seat covers with non-Toyota leather or other seat cover materials may compromise the effectiveness of this safety system. The design of the seat is complex, integrating safety and strength with comfort and luxury. Toyota strongly discourages modifying original equipment seats that have optional side airbags. Additionally, Toyota strongly advises against the installation or use of aftermarket seat covers, which could impair the performance of the side airbags in the event of an accident.
T-TT-0268-13
Service Bulletin/Repair Instructions
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
T-TT-0269-13
Service Bulletin/Repair Instructions
The appearance of spots in tempered glass (when viewed at certain angles) is the result of the heat treating and quick quenching process during manufacturing.
T-SB-0071-11 Rev
Service Bulletin/Repair Instructions
The purpose of this service bulletin is to provide precautions to follow when installing an automatic transmission/transaxle assembly to avoid MIL ?ON,? shifting issues, and/or transmission damage. Use the information in this bulletin when installing an automatic transmission/transaxle assembly
T-TT-0051-10
Service Bulletin/Repair Instructions
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
T-TT-0051-10 Rev
Service Bulletin/Repair Instructions
If a customer states there is an unpleasant odor in the vehicle from the HVAC system, there are various factors that may be involved.
T-SB-0141-13
Service Bulletin/Repair Instructions
A new Special Service Tool (SST 09709-00002) has been introduced to aid in the inspection procedure for certain vehicles equipped with a floor pedal-type parking brake system. This bulletin references the correct method for installing the Brake Pedal Force Gauge. Refer to the appropriate Repair Manual for parking brake pedal travel inspection and adjustment specification.
T-SB-0249-12 Rev
Service Bulletin/Repair Instructions
This bulletin is no longer applicable and is now obsolete.
TC13-019
Service Bulletin/Repair Instructions
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
T-SB-0066-11 Rev
Service Bulletin/Repair Instructions
Some 2005 ? 2013 model year Tacoma vehicles equipped with a 5-speed manual transmission may exhibit a slipping feeling in all forward gears and reverse. Replacement of the clutch disk, clutch cover, flywheel, and clutch pedal turnover spring is required to repair the vehicle. Follow the repair procedure in this bulletin to address this condition.
T-TT-0124-11
Service Bulletin/Repair Instructions
Please refer to the following recommendations for the best practices for vehicle tire rotations.
T-SB-0057-13
Service Bulletin/Repair Instructions
Some 2005 ? 2013 model year Tacoma vehicles equipped with a 5-speed automatic transmission may exhibit a whine noise from the rear differential between 50 ? 60 mph (80 ? 97 km/h). Use the following Repair Procedure to address this condition.
TSB-0057-13
Service Bulletin/Repair Instructions
TOYOTA: ON SOME VEHICLES, WITH 5 SPEED AUTOMATIC TRANSMISSION, CAN HEAR A WHINNYING NOISE COMING FROM THE REAR DIFFERENTIAL. MODEL 2005-2013 TACOMA. *PE
T-PG006-00 Obsol
Service Bulletin/Repair Instructions
This bulletin is now obsolete. Please see T-SB-0054-13.
T-SB-0054-13
Service Bulletin/Repair Instructions
California (CA), Federal (FED), and 50 State Certified emission control underhood labels (emission labels) may be obtained through your dealership?s Parts Department utilizing standard replacement parts ordering procedures. Follow the guidelines outlined in this bulletin to ensure proper label application.
T-SB-0141-10 Rev
Service Bulletin/Repair Instructions
If a creak, tick, or rattle noise is heard at the top or bottom of the windshield, or at the top of the rear glass, the source of the noise may be the two stoppers bonded to the top of the windshield/rear glass, or the windshield retainers bonded to the lower edge of the windshield. This bulletin provides the recommended repair procedure to eliminate these types of noises from the windshield/rear glass area.
Renotification (
Service Bulletin/Repair Instructions
Toyota will be sending Safety Recall Follow Up Notices to remind owners whose vehicles have not yet had campaign repair completed. Please note the following information for Regional and PD associates.
T-TT-0226-13
Service Bulletin/Repair Instructions
The customer is having difficulty changing the multi-display screen from Day Mode. If the multi-display screen is set to Day Mode when the headlights are on, the setting we be memorized when the engine is turned off.
T-SB-0391-08 Rev
Service Bulletin/Repair Instructions
This bulletin contains general vehicle pulling diagnosis and repair procedures along with specific information to help correct pulling complaints.
SST Requirements
Service Bulletin/Repair Instructions
SSTs are key elements to provide your customers with swift and accurate repairs resulting in superior customer satisfaction.
T-SB-0016-13
Service Bulletin/Repair Instructions
Some 4WD 2005 ? 2012 model year Tacoma vehicles equipped with an automatic transmission may exhibit a clunk/thunk noise from the rear of the vehicle or a ?bump-from-behind? sensation just before a stop or when accelerating from a stop. Improvements have been implemented on the rear propeller shaft (driveshaft) to reduce this condition. Follow the Repair Procedure in this bulletin to improve this condition.
T-SB-0012-13
Service Bulletin/Repair Instructions
Flash reprogramming allows the ECU software to be updated without replacing the ECU. Flash calibration updates for specific vehicle models/ECUs are released as field-fix procedures described in individual Service Bulletins. This bulletin details the Techstream ECU flash reprogramming process and outlines use of the TIS and the CUW.
T-SB-0064-10 Rev
Service Bulletin/Repair Instructions
This bulletin is now obsolete. Please see T-SB-0012-13.
T-SB-0132-08 Obs
Service Bulletin/Repair Instructions
This bulletin is now obsolete. Please see T-SB-0249-12 .
T-SB-0249-12
Service Bulletin/Repair Instructions
Some vehicles may exhibit a vibration felt in the seat, floorboard, and/or steering wheel around 15-25 MPH caused by a second order driveline vibration. Use the following procedure to address this condition.
T-SB-0250-12
Service Bulletin/Repair Instructions
Some 2WD 2005 ? 2013 model year Tacoma vehicles equipped with an automatic transmission may exhibit a clunk/thunk noise from the rear of the vehicle or a ?bump-from-behind? sensation just before a stop or when accelerating from a stop. Improvements have been implemented on the rear propelled shaft (driveshaft). Follow the Repair Procedure in this bulletin to improve this condition.
TSB-0249-12
Service Bulletin/Repair Instructions
TOYOTA: THE DRIVELINE VIBRATES BETWEEN 15-25 MPH. MODEL 2005-2013 TACOMA. *PE
T-SB-0187-12
Service Bulletin/Repair Instructions
Toyota vehicles are equipped with either conventional or run-flat tires. Sometimes punctures may occur as a result of contact with road debris or other hazards. If a puncture occurs, it may be possible to repair the tire and return it to service. With a conventional tire it is not possible to drive for an extended amount of time with the tire at low pressures as damage to the tire may occur. With run-flat tires, due to reinforced sidewalls, it is possible to drive for up to 100 miles (160 km) at speeds less than 55 mph (90 km/h) with little or no damage to the tire.
T-SB-0186-12
Service Bulletin/Repair Instructions
Some 2005 ? 2012 model year Tacoma vehicles may exhibit a squeak or creak noise from the clutch pedal when it is depressed or released. Changes have been made to the clutch pedal and clutch master cylinder assembly to address this condition.
TSB-0087-12
Service Bulletin/Repair Instructions
TOYOTA: ACCELERATOR PEDAL SENSOR ASSEMBLY INFORMATION REGARDING THE INSPECTION, REMOVAL, AND INSTALLATION, IF LUBRICATION OR OIL, IS APPLIED. *PE
T-SB-0057-12
Service Bulletin/Repair Instructions
TOYOTA: STEERING INTERMEDIATE SHAFT RATTLE NOISE. SOME VEHICLES MAY EXHIBIT STEERING RATTLE NOISE WHEN DRIVEN OVER ROUGH ROAD SURFACES. ALSO INCLUDED 2WD TACOMA PRERUNNER. MODEL YEARS 2005-2012. *JS
T-SB-0129-11
Service Bulletin/Repair Instructions
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
TSB-0122-11
Service Bulletin/Repair Instructions
TOYOTA: INFORMATION PROVIDED FOR REPLACING THE SEAT COVERS FOR VEHICLES EQUIPPED WITH SIDE AIRBAGS. *PE
T-SB-0066-11
Service Bulletin/Repair Instructions
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
TSB-0049-11
Service Bulletin/Repair Instructions
TOYOTA: INFORMATION ON INSTALLING MANUAL TRANSMISSION SHIFT LEVER OR PARK NEUTRAL POSITION SWITCH. *RM
SB-0119-10 REV2
Service Bulletin/Repair Instructions
TOYOTA: SOME TOYOTA TACOMA VEHICLES MANUFACTURED BETWEEN 2005 AND 2011 MAY HAVE A STEERING RATTLE NOISE WHEN DRIVING ON ROUGH SURFACES. *RM
TSB-0064-10
Service Bulletin/Repair Instructions
TOYOTA: TECHSTREAM ECU FLASH REPROGRAMMING PROCEDURE. FLASH REPROGRAMMING ALLOWS THE ECU SOFTWARE TO BE UPDATED WITHOUT REPLACING THE ECU. FLASH CALIBRATION UPDATES FOR SPECIFIC VEHICLE MODELS/ECUS ARE RELEASED AS FIELD-FIX PROCEDURES DESCRIBED IN INDIVIDUAL SERVICE BULLETINS. MODEL YEARS FROM 2001-2011. *PE
SB-0397-09 REV1
Service Bulletin/Repair Instructions
TOYOTA: VEHICLE INTERIOR: INTERIOR PANELS/TRIM TO IMPROVE SERVICEABILITY OF THE FLOOR CARPET GROMMET (FLOOR CLAMP RETAINER), A NEW SERVICE PART HAS BEEN DEVELOPED WHICH ALLOWS THE FLOOR CARPET GROMMET TO BE REPLACED SEPARATELY FROM THE CARPET ASSEMBLY. MODELS INCLUDE AVALON, CAMRY, CAMRY HV, PRIUS, TACOMA AND TUNDRA. *PE.
SB-0277-09
Service Bulletin/Repair Instructions
TOYOTA: AUTOMATIC TRANSMISSION/TRANSAXLE. SOME VEHICLES MAY EXHIBIT A MIL ON CONDITION WITH DTC P0705 (TRANSMISSION RANGE SENSOR CIRCUIT MALFUNCTION (PRNDL INPUT)) STORED. COMMON SYMPTOMS WITH THIS DTC CAN INCLUDE POSSIBLE DELAYED ENGAGEMENT INTO REVERSE OR DRIVE AND POSSIBLE HARSH GEAR ENGAGEMENT WHEN SHIFTING BETWEEN PARK OR NEUTRAL INTO ALL OTHER GEARS. *PE
T-SB-0076-08
Service Bulletin/Repair Instructions
REAR DIFFERENTIAL WHINE OR HOWLING NOISE AT HIGHWAY SPEEDS. *PE
00407
Service Bulletin/Repair Instructions
DRIVER AND PASSENGER'S SIDE FLOOR MATS. *NJ
00406
Service Bulletin/Repair Instructions
DIRECT-TYPE TIRE PRESSURE WARNING SYSTEM DIAGNOSTIC TIPS. *KB
T-PG007-01
Service Bulletin/Repair Instructions
Replacement vin plates.
T-PG002-91
Service Bulletin/Repair Instructions
Product general information.