Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
T-SB-0035-24 Rev2
Service Bulletin/Repair Instructions
Acid rain results from rainwater or other airborne moisture that become acidic due to industrial chemical impurities in the atmosphere. If these acidic compounds settle on an exposed vehicle, especially the horizontal areas such as the hood, roof, and decklid, significant damage to the painted surfaces can occur. Acid rain damage can typically be identified on vehicles by the presence of stains on the paint surface that resemble hard water spots. Unlike water spots however, acid rain damage cannot be removed by regular washing procedures. Also, because acid rain can etch and soften the paint, normal buffing or polishing repair procedures should not be attempted. This can cause further damage and result in visible depressions in the paint surface. The following are the three major categories of acid rain damage: •Minor damage: requires only buffing to repair. •Moderate damage: usually requires neutralizing, color sanding, and buffing. •Severe damage: extending beyond 1/2 mil of clearcoat on a pearl, metallic, or solid color, requires neutralization, sanding, and repainting. In cases where acid rain damage is minor, neutralization and buffing with a liquid-type paint finessing product may provide an adequate repair. Only specially formulated products outlined in this bulletin should be used for that purpose. Unfortunately, other than minor damage, there is no simple method of determining the actual extent (depth) of acid penetration other than color sanding a representative affected area until there is no visible etching or depressions, followed by measuring the amount of paint removed with either a magnetic or digital-type film thickness gauge. The procedures in this bulletin are intended for use by qualified body/paint technicians and should not be attempted by inexperienced personnel. It is the dealer’s responsibility to protect and maintain the quality of the vehicle’s paint finish after receipt at the dealership prior to the first sale. Perform frequent vehicle washing, as often as daily, during high heat and humidity periods to minimize the potential for paint damage due to acid rain exposure. This is especially important in geographical areas known for high frequency and concentration of acid rain and industrial fallout.
T-SB-0038-24 Rev2
Service Bulletin/Repair Instructions
To prevent brake rotor rust from forming during transportation and storage, wheel film will be used instead of a cardboard type of anti-rust cover. The purpose of the wheel film is to shield the disc brake rotor from weather elements and initial rust before the vehicle is delivered to the customer. Consequently, the film should remain on the wheel for as long as possible.
T-SB-0039-24 Rev2
Service Bulletin/Repair Instructions
The condition known as acid rain is caused by airborne chemicals or particles in the atmosphere, which mix with rainwater, nighttime dew, or high humidity to form acidic compounds. If these contaminants settle and remain on a painted vehicle surface, especially the horizonal areas of the hood, roof, and decklid, significant damage can occur. This damage is the result of actual etching of the paint and appears as pitting or water spots. As acid rain droplets on the vehicle surface evaporate, the concentration strength of the acid increases, causing deeper and more rapid damage. This evaporation and corrosive action also occur more rapidly on dark colored cars as direct sun heat increases. It is the dealer’s responsibility to protect and maintain the quality of the vehicle’s paint finish after receipt at the dealership prior to the first sale. In areas known for high frequency and/or concentration of acid rain, frequent vehicle washing during high heat or humidity periods will minimize the potential for paint damage caused by acid rain. It is further recommended that either reverse osmosis or deionized water be used to prevent water spotting.
T-SB-0061-23 Rev2
Service Bulletin/Repair Instructions
Toyota vehicles are currently protected with RapgardTM protective film designed to protect the horizontal painted surfaces. This material protects from acid rain, environmental fallout, and rail contamination. Follow the Removal Procedure in this bulletin to remove the RapgardTM protective film within 90 days from initial application.
T-SB-0062-23 Rev2
Service Bulletin/Repair Instructions
Vehicles may occasionally be subjected to contamination by airborne iron particles shed from railroad tracks, train wheels, exposure to heavy machinery facilities, grinding, welding, etc. This type of contamination can be identified by the presence of small, red or brown particles on the paint surface. These particles are often difficult to see on dark color paints but can be easily felt when brushing a hand across horizontal body surfaces such as the hood, roof, or deck lid. Follow the Repair Procedure in this bulletin to clean vehicles that may have been subjected to contamination by airborne iron particles such as rail dust during rail transportation or extended storage near industrial areas.
T-SB-0035-24 Rev1
Service Bulletin/Repair Instructions
Acid rain results from rainwater or other airborne moisture that become acidic due to industrial chemical impurities in the atmosphere. If these acidic compounds settle on an exposed vehicle, especially the horizontal areas such as the hood, roof, and decklid, significant damage to the painted surfaces can occur. Acid rain damage can typically be identified on vehicles by the presence of stains on the paint surface that resemble hard water spots. Unlike water spots however, acid rain damage cannot be removed by regular washing procedures. Also, because acid rain can etch and soften the paint, normal buffing or polishing repair procedures should not be attempted. This can cause further damage and result in visible depressions in the paint surface. The following are the three major categories of acid rain damage: •Minor damage: requires only buffing to repair. •Moderate damage: usually requires neutralizing, color sanding, and buffing. •Severe damage: extending beyond 1/2 mil of clearcoat on a pearl, metallic, or solid color, requires neutralization, sanding, and repainting. In cases where acid rain damage is minor, neutralization and buffing with a liquid-type paint finessing product may provide an adequate repair. Only specially formulated products outlined in this bulletin should be used for that purpose. Unfortunately, other than minor damage, there is no simple method of determining the actual extent (depth) of acid penetration other than color sanding a representative affected area until there is no visible etching or depressions, followed by measuring the amount of paint removed with either a magnetic or digital-type film thickness gauge. The procedures in this bulletin are intended for use by qualified body/paint technicians and should not be attempted by inexperienced personnel. It is the dealer’s responsibility to protect and maintain the quality of the vehicle’s paint finish after receipt at the dealership prior to the first sale. Perform frequent vehicle washing, as often as daily, during high heat and humidity periods to minimize the potential for paint damage due to acid rain exposure. This is especially important in geographical areas known for high frequency and concentration of acid rain and industrial fallout.
T-SB-0038-24 Rev1
Service Bulletin/Repair Instructions
To prevent brake rotor rust from forming during transportation and storage, wheel film will be used instead of a cardboard type of anti-rust cover. The purpose of the wheel film is to shield the disc brake rotor from weather elements and initial rust before the vehicle is delivered to the customer. Consequently, the film should remain on the wheel for as long as possible.
T-SB-0039-24 Rev1
Service Bulletin/Repair Instructions
The condition known as acid rain is caused by airborne chemicals or particles in the atmosphere, which mix with rainwater, nighttime dew, or high humidity to form acidic compounds. If these contaminants settle and remain on a painted vehicle surface, especially the horizonal areas of the hood, roof, and decklid, significant damage can occur. This damage is the result of actual etching of the paint and appears as pitting or water spots. As acid rain droplets on the vehicle surface evaporate, the concentration strength of the acid increases, causing deeper and more rapid damage. This evaporation and corrosive action also occur more rapidly on dark colored cars as direct sun heat increases. It is the dealer’s responsibility to protect and maintain the quality of the vehicle’s paint finish after receipt at the dealership prior to the first sale. In areas known for high frequency and/or concentration of acid rain (see Figure 1), frequent vehicle washing during high heat or humidity periods will minimize the potential for paint damage caused by acid rain. It is further recommended that either reverse osmosis or deionized water be used to prevent water spotting.
T-SB-0061-23 Rev1
Service Bulletin/Repair Instructions
Toyota vehicles are currently protected with RapgardTM protective film designed to protect the horizontal painted surfaces. This material protects from acid rain, environmental fallout, and rail contamination.
T-SB-0062-23 Rev1
Service Bulletin/Repair Instructions
Vehicles may occasionally be subjected to contamination by airborne iron particles shed from railroad tracks, train wheels, exposure to heavy machinery facilities, grinding, welding, etc. This type of contamination can be identified by the presence of small, red or brown particles on the paint surface. These particles are often difficult to see on dark color paints but can be easily felt when brushing a hand across horizontal body surfaces such as the hood, roof, or deck lid.
T-SB-0035-24
Service Bulletin/Repair Instructions
Acid rain results from rainwater or other airborne moisture that become acidic due to industrial chemical impurities in the atmosphere. If these acidic compounds settle on an exposed vehicle, especially the horizontal areas such as the hood, roof, and decklid, significant damage to the painted surfaces can occur. Acid rain damage can typically be identified on vehicles by the presence of stains on the paint surface that resemble hard water spots. Unlike water spots however, acid rain damage cannot be removed by regular washing procedures. Also, because acid rain can etch and soften the paint, normal buffing or polishing repair procedures should not be attempted. This can cause further damage and result in visible depressions in the paint surface. The following are the three major categories of acid rain damage: •Minor damage: requires only buffing to repair. •Moderate damage: usually requires neutralizing, color sanding, and buffing. •Severe damage: extending beyond 1/2 mil of clearcoat on a pearl, metallic, or solid color, requires neutralization, sanding, and repainting. In cases where acid rain damage is minor, neutralization and buffing with a liquid-type paint finessing product may provide an adequate repair. Only specially formulated products outlined in this bulletin should be used for that purpose. Unfortunately, other than minor damage, there is no simple method of determining the actual extent (depth) of acid penetration other than color sanding a representative affected area until there is no visible etching or depressions, followed by measuring the amount of paint removed with either a magnetic or digital-type film thickness gauge. The procedures in this bulletin are intended for use by qualified body/paint technicians and should not be attempted by inexperienced personnel. While the quality and durability of paint on Toyota vehicles is continuously being improved, it remains the dealer’s responsibility to protect and maintain the quality of the vehicle’s paint finish after receipt at the dealership prior to the first sale. To read, While the quality and durability of paint on Toyota vehicles is continuously being improved, it remains the dealer’s responsibility to protect and maintain the quality of the vehicle’s paint finish after receipt at the dealership prior to first sale. Perform frequent vehicle washing, as often as daily, during high heat and humidity periods to minimize the potential for paint damage due to acid rain exposure. This is especially important in geographical areas known for high frequency and concentration of acid rain and industrial fallout.
T-SB-0038-24
Service Bulletin/Repair Instructions
To prevent brake rotor rust from forming during transportation and storage, wheel film will be used instead of a cardboard type of anti-rust cover. The purpose of the wheel film is to shield the disc brake rotor from weather elements and initial rust before the vehicle is delivered to the customer. Consequently, the film should remain on the wheel for as long as possible. SUPERSESSION NOTICE The information contained in this bulletin supersedes Service Bulletin No. PD017-04. •The entire bulletin has been updated.
T-SB-0039-24
Service Bulletin/Repair Instructions
The condition known as acid rain is caused by airborne chemicals or particles in the atmosphere, which mix with rainwater, nighttime dew, or high humidity to form acidic compounds. If these contaminants settle and remain on a painted vehicle surface, especially the horizonal areas of the hood, roof, and decklid, significant damage can occur. This damage is the result of actual etching of the paint and appears as pitting or water spots. As acid rain droplets on the vehicle surface evaporate, the concentration strength of the acid increases, causing deeper and more rapid damage. This evaporation and corrosive action also occur more rapidly on dark colored cars as direct sun heat increases. While Toyota paint quality, durability, and resistance to environmental factors is continuously being improved, it remains the responsibility of the dealer to protect and maintain the vehicle’s paint finish from the time of arrival at the dealership until retail delivery to the customer. In areas known for high frequency and/or concentration of acid rain (see Figure 1), frequent vehicle washing during high heat or humidity periods will minimize the potential for paint damage caused by acid rain. It is further recommended that either reverse osmosis or deionized water be used to prevent water spotting.
T-PANT-2024-004-
Service Bulletin/Repair Instructions
This is to advise of various price adjustments that will affect Toyota Genuine Motor Oil and Long Life Coolant, effective March 1, 2024. These products are ordered through the Toyota Complete Maintenance Care (TCMC) website.
T-SB-0043-14
Service Bulletin/Repair Instructions
OBSOLETE NOTICE January 22, 2024: This bulletin is now obsolete. Please see T-SB-0057-18.
TSB003220
Service Bulletin/Repair Instructions
TSB: Replacement certification labels (the vinyl label installed on the driver door or door post) and VIN plates (the metal plate riveted to dashboard) (see Figure 1) for most 1979 ? 2023 model year vehicles may be available provided the requests meet the criteria listed in this Service Bulletin. Follow the Procurement Procedure in this bulletin to request a replacement certification label or VIN plate.
TTT063620
Service Bulletin/Repair Instructions
TT: Some Toyota vehicles installed with Toyota Complete Maintenance Care (TCMC) brake pads may exhibit a groan or squeak noise in various driving conditions
T-SB-0014-22
Service Bulletin/Repair Instructions
TSB: This Service Bulletin includes procedures to replace damaged or loose front carpet floor retainer(s) without replacing the carpet assembly. Follow the Repair Procedure in this bulletin to replace the loose or damaged carpet floor retainer(s).
Toyota Safety Re
Service Bulletin/Repair Instructions
Toyota Safety Recall and Service Campaign - Technician Certification Requirements
T-TT-0636-20 Rev
Service Bulletin/Repair Instructions
TT: Some Toyota vehicles installed with Toyota Complete Maintenance Care (TCMC) brake pads may exhibit a groan or squeak noise in various driving conditions.
T-SB-0032-20 Rev
Service Bulletin/Repair Instructions
TSB: Replacement certification labels (the vinyl label installed on the driver door or door post) and VIN plates (the metal plate riveted to dashboard) (see Figure 1) for most 1979 ? 2021 model year vehicles may be available provided the requests meet the criteria listed in this Service Bulletin. Follow the Procurement Procedure in this bulletin to request a replacement certification label or VIN plate.
T-TT-0636-20
Service Bulletin/Repair Instructions
TT: Some Toyota vehicles installed with Toyota Complete Maintenance Care (TCMC) brake pads may exhibit a groan or squeak noise in various driving conditions.
T-SB-0304-17 Obs
Service Bulletin/Repair Instructions
TSB: OBSOLETE NOTICE April 07, 2020: This bulletin is now obsolete. Please see T-SB-0032-20. Replacement Certification Labels and VIN Plates
T-SB-0032-20
Service Bulletin/Repair Instructions
TSB: SUPERSESSION NOTICE The information contained in this bulletin supersedes Service Bulletin Nos. PG021-88, PG015-89, PG0015-90, PG002-91, PG002-93, PG005-97, PG007-01, PG007-07, PG006-01, PG004-97, T-SB-0144-08, and T-SB-0304-17. The aforementioned bulletins are obsolete, and any printed versions should be discarded. Replacement certification labels (the vinyl label installed on the driver door or door post) and VIN plates (the metal plate riveted to dashboard) (see Figure 1) for most 1979 ? 2020 model year vehicles may be available provided the requests meet the criteria listed in this Service Bulletin. Follow the Procurement Procedure in this bulletin to request a replacement certification label or VIN plate.
T-SB-0008-20
Service Bulletin/Repair Instructions
TSB: Vehicles may display evidence of a fluid leak or fluid seep from powertrain components. This bulletin explains how to determine the differences between a fluid leak versus a fluid seep. Cases that are determined to be a ?leak? should be repaired accordingly and will be covered under warranty if applicable. Cases that are determined to be a ?seep? should be documented on the repair order and inspected at the next service interval. Follow the Repair Information in this bulletin to determine if the concern in question is a fluid leak or fluid seep and review the Repair Procedure section to address the condition. NOTE This bulletin applies to ALL powertrain fluids excluding fuel and coolant.
PG004-97-Obsolet
Service Bulletin/Repair Instructions
Technical Service Bulletin: OBSOLETE NOTICE: July 31, 2018: This bulletin is now obsolete. Please see T-SB-0304-17.
PG006-01-Obsolet
Service Bulletin/Repair Instructions
Technical Service Bulletin: OBSOLETE NOTICE: July 31, 2018: This bulletin is now obsolete. Please see T-SB-0304-17.
T-SB-0304-17_Rev
Service Bulletin/Repair Instructions
TSB: REVISION NOTICE July 31, 2018 Rev2: ? The Supersession Notice has been updated. January 11, 2018 Rev1: ? The Supersession Notice has been updated. Any previous printed versions of this bulletin should be discarded. SUPERSESSION NOTICE The information contained in this bulletin supersedes Service Bulletin Nos. PG021-88, PG015-89, PG0015-90, PG002-91, PG002-93, PG005-97, PG007-01, PG007-07, PG006-01, PG004-97, and T-SB-0144-08. Service Bulletin Nos. PG021-88, PG015-89, PG0015-90, PG002-91, PG002-93, PG005-97, PG007-01, PG007-07, PG006-01, PG004-97, and T-SB-0144-08 are obsolete and any printed versions should be discarded. Vehicle replacement certification labels (the vinyl label installed on the driver door or door post) and VIN plates (the metal plate riveted to dashboard) may be available from Toyota, provided the request meets one of the criteria listed in this Service Bulletin. Replacement Certification Label and VIN Plate Criteria A replacement certification label and/or VIN plate may be requested if: ? The vehicle was in an accident and the label and/or plate is damaged or attached to a part that will be replaced during the repair. ? The label and/or plate was stolen.
T-SB-0057-18
Service Bulletin/Repair Instructions
TSB: SUPERSESSION NOTICE The information contained in this bulletin supersedes Service Bulletin No. T-SB-0043-14. ? Applicability has been updated to include 2017 ? 2018 model year Toyota vehicles. Service Bulletin No. T-SB-0043-14 is obsolete and any printed versions should be discarded. The Immobilizer and Smart Key Reset is a feature that allows the registration of new keys when all master keys are lost. Once the system is reset, all previously registered keys will be erased. Follow the procedures in this bulletin to reset a vehicle Immobilizer or Smart Key system. NOTE New security provisions are required to obtain a reset passcode. It is critical to review the instructions for this new process BEFORE attempting to get a passcode in the new system.
Toyota PRO18-03_
Service Bulletin/Repair Instructions
Mis-Built For frames that are suspected to have been mis-built, dealers should: 1. Contact the Parts Technical Support Group (PTSG) at prasupport@toyota.com with information on the condition and status of repair. a. Include the original part order reference number. 2. A Field Product Quality Report (FPQR) should be generated and attached to the communication. a. The report should include photos of the condition and of all labels and stampings on the frame. b. This report can be submitted by region staff (FTS) or dealership personnel. 3. Dealership will receive communication back with next direction(s) from PTSG. a. Response will include confirmation of mis-built condition and if applicable,
ZH6, ZH7, ZH8, Z
Service Bulletin/Repair Instructions
Dealer Daily Message: Frame Programs. Extension of Warranty Coverage for Frame Corrosion/Frame Replacement. Frame Ordering/Repair/Administration Updates Mis-Built. For frames that are suspected to have been mis-built, dealers should: 1. Contact the Parts Technical Support Group (PTSG) at prasupport@toyota.com with information on the condition and status of repair. Also include the original part order reference number. a. A Field Product Quality Report (FPQR) should also be generated and attached to the communication. i. The report should include photos of the condition, and photos of all labels and stampings on the frame. ii. This report can be submitted by region staff (FTS) or dealership personnel. 2. Dealership will receive communication back with next direction(s) from PTSG. a. Response will include confirmation of mis-built condition, if applicable, and instructions on mis-built frame disposition.
T-SB-0229-12_Rev
Service Bulletin/Repair Instructions
TSB: REVISION NOTICE November 22, 2017 Rev1: ? Applicability has been updated to include 2014 ? 2018 model year vehicles. Any previous printed versions of this bulletin should be discarded. In the event that a Toyota vehicle becomes submerged in water, many components may be physically damaged. Electrical and electronic components, including wiring harnesses, are particularly susceptible to corrosion and subsequent malfunction. Although any flooding can be damaging, salt water flooding elevates the potential for abnormal conditions and may increase risks due to its highly corrosive and conductive nature. Salt residue also continues to corrode and remain conductive even after a vehicle dries. This bulletin is intended to assist with safe handling and inspection of flood damaged vehicles and to provide basic guidance on likely needed repairs.
T-SB-0144-08_Obs
Service Bulletin/Repair Instructions
TSB: OBSOLETE NOTICE November 21, 2017: This bulletin is now obsolete. Please see T-SB-0304-17.
T-SB-0304-17
Service Bulletin/Repair Instructions
TSB: Vehicle replacement certification labels (the vinyl label installed on the driver door or door post) and VIN plates (the metal plate riveted to dashboard) may be available from Toyota, provided the request meets one of the criteria listed in this Service Bulletin.
T-SB-0218-17_Rev
Service Bulletin/Repair Instructions
TSB: REVISION NOTICE July 20, 2017 Rev1: Applicability has been updated to exclude 2007 ? 2017 model year Avanza vehicles. Some hazardous material treatment and handling regulations at the state and local level define the pre-disposal deployment of airbag and pre-tensioner assemblies as hazardous material treatment. Hazardous material treatment may require special training, certification or licensing in certain areas. TMS recommends that dealership personnel carefully review and follow ALL local and state regulations, and where necessary, contract with Environmental Protection Agency (EPA) Licensed Hazardous Waste Transportation and Disposal facilities.
TSB018217
Service Bulletin/Repair Instructions
TSB: SUPERSESSION NOTICE The information contained in this bulletin supersedes SB No. T-SB-0101-11. Applicability has been updated to include 2016 ? 2017 model year vehicles. Service Bulletin No. T-SB-0101-11 is Obsolete and any printed versions should be discarded. Be sure to review the entire content of this bulletin before proceeding. When servicing interior electrical switches and components, please note the precautions in this bulletin to avoid damaging electrical components and switches. Many lubricants, cleaners, and automotive chemicals contain silicone or other compounds that may contaminate electrical contacts, and therefore increase electrical resistance and decrease switch performance. The use of any cleaners or fluids may increase the risk of further damage to electrical components.
Safety Recall an
Service Bulletin/Repair Instructions
Update on Technician Certification Requirements.
9SM_DEALER 2/16
Service Bulletin/Repair Instructions
THIS CAMPAIGN EXPIRED ON DECEMBER 31, 2012.
9SM_Dealer Lette
Service Bulletin/Repair Instructions
This Campaign Expired on December 31, 2012.
9SM_TECH 2/16
Service Bulletin/Repair Instructions
THIS CAMPAIGN EXPIRED ON DECEMBER 31, 2012.
9SM_Technical In
Service Bulletin/Repair Instructions
This Campaign Expired on December 31, 2012.
T-TT-0362-15
Service Bulletin/Repair Instructions
TT: The vehicle may be difficult to start or have an abnormally low or rough idle after the battery has been disconnected or power to the Engine ECM has been interrupted.
T-TT-0086-11
Service Bulletin/Repair Instructions
TechTip: Condition - The vehicle may be difficult to start or have an abnormally low or rough idle after the battery has been disconnected or power to the Engine ECM has been interrupted.
T-SB-0043-14 Rev
Service Bulletin/Repair Instructions
TSB: The Immobilizer and Smart Key Reset is a feature that allows the registration of new keys when all master keys are lost. Once the system is reset, all previously registered keys will be erased. Follow the procedures in this bulletin to reset a vehicle Immobilizer or Smart Key system. NOTE: There are new security provisions required to obtain a Reset Pass-Code. It is critical that the instructions for this new process are reviewed BEFORE attempting to get a Pass-Code in the new system.
T-SB-0083-13 Rev
Service Bulletin/Repair Instructions
TSB: The procedure in this bulletin is a general guideline on how to properly diagnose the air conditioning system after a component failure. Refer to the applicable Repair Manual for vehicle specific repair procedures and parts.
T-SB-0014-11 Rev
Service Bulletin/Repair Instructions
TSB: The purpose of this service bulletin is to provide information regarding the installation of the correct torque converter bolts during automatic transmission/transaxle assembly replacement. Incorrect torque converter bolts or missing washers can cause damage to the torque converter assembly.
T-SB-0134-14
Service Bulletin/Repair Instructions
TSB: The purpose of this bulletin is to provide precautions to follow when installing an automatic transmission/transaxle assembly to avoid MIL "ON" shifting issues and/or transmission damage. Use the information in this bulletin when installing an automatic transmission/transaxle assembly.
T-TT-0010-10 Rev
Service Bulletin/Repair Instructions
Tech Tip: Low battery voltage can contribute to a MIL "ON" condition for P0335 (Crankshaft Position Sensor Circuit) and/or P0340 (Camshaft Position Sensor Circuit) due to inconsistent rotational speed of the engine's crankshaft.
T-TT-0132-11
Service Bulletin/Repair Instructions
A key part to maintain the proper function and safe operation of the vehicle's braking system is to perform a visual inspection when installing brake pads, calipers, and discs. The following recommendations are intended to provide general tips for the inspection and/or installation of Toyota Complete Maintenance Care (TCMC) front brake pads and discs. Always refer to the model specific Repair manual and TIS publications for specific repair instructions.
T-TT-0213-13
Service Bulletin/Repair Instructions
Toyota vehicles are equipped with Supplemental Restraint Systems (SRS), including various airbags and in some models, seat belt pre-tensioners, to help reduce the risk of injury in a collision. If a customer expresses any concerns that the SRS airbags or pre-tensioner devices did not perform as expected (including an unintended deployment event), please follow the steps in the recommendations section below.
T-SB-0185-13
Service Bulletin/Repair Instructions
The following procedures are recommended during routine maintenance or in the event of a customer concern for wiper performance.
TS-BO030-01 Obso
Service Bulletin/Repair Instructions
This bulletin is now obsolete. Please see T-SB-0185-13.
T-SB-0122-11 Rev
Service Bulletin/Repair Instructions
Beginning in 1998, Toyota introduced side airbags as optional equipment. Toyota does NOT recommend replacement of original seat covers with non-Toyota leather or other seat cover materials on vehicles due to the following: Seat covers NOT recommended by Toyota may affect side airbag performance, in general or in part, during an accident. Modifications that negatively affect side airbag performance can result in severe occupant injuries. Seat covers are an integral part of this safety system. Replacing fabric seat covers with non-Toyota leather or other seat cover materials may compromise the effectiveness of this safety system. The design of the seat is complex, integrating safety and strength with comfort and luxury. Toyota strongly discourages modifying original equipment seats that have optional side airbags. Additionally, Toyota strongly advises against the installation or use of aftermarket seat covers, which could impair the performance of the side airbags in the event of an accident.
T-SB-0071-11 Rev
Service Bulletin/Repair Instructions
The purpose of this service bulletin is to provide precautions to follow when installing an automatic transmission/transaxle assembly to avoid MIL ?ON,? shifting issues, and/or transmission damage. Use the information in this bulletin when installing an automatic transmission/transaxle assembly
T-SB-0141-13
Service Bulletin/Repair Instructions
A new Special Service Tool (SST 09709-00002) has been introduced to aid in the inspection procedure for certain vehicles equipped with a floor pedal-type parking brake system. This bulletin references the correct method for installing the Brake Pedal Force Gauge. Refer to the appropriate Repair Manual for parking brake pedal travel inspection and adjustment specification.
TC13-019
Service Bulletin/Repair Instructions
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
T-PG006-00 Obsol
Service Bulletin/Repair Instructions
This bulletin is now obsolete. Please see T-SB-0054-13.
T-SB-0054-13
Service Bulletin/Repair Instructions
California (CA), Federal (FED), and 50 State Certified emission control underhood labels (emission labels) may be obtained through your dealership?s Parts Department utilizing standard replacement parts ordering procedures. Follow the guidelines outlined in this bulletin to ensure proper label application.
TC-12-006
Service Bulletin/Repair Instructions
TOYOTA: SEE DOCUMENT SEARCH BUTTON FOR OWNER LETTER. IN CERTAIN COLD CLIMATE AREAS, WITH HIGH USAGE OF ROAD SALT, FRAMES OF TRUCKS WOULD EXHIBIT MORE THAN NORMAL RUST CORROSION, CAUSING PERFORATION OF METAL. MODELS 2000-03 TUNDRA. *PE
LSC-9SM
Service Bulletin/Repair Instructions
TOYOTA: SOME VEHICLES MAY EXPERIENCE EXCESSIVE CORROSION OF REAR CROSS MEMBER AND FUEL TANK MOUNTING SYSTEM AND STRAPS WHEN OPERATED IN COLD CLIMATE AREAS. *PE
TSB-0122-11
Service Bulletin/Repair Instructions
TOYOTA: INFORMATION PROVIDED FOR REPLACING THE SEAT COVERS FOR VEHICLES EQUIPPED WITH SIDE AIRBAGS. *PE
5182B
Service Bulletin/Repair Instructions
STEERING - POWER STEERING GEAR. REPAIR MANUAL CORRECTION. 00400-RM682-U2. *TT
4493B
Service Bulletin/Repair Instructions
2001 TUNDRA REPAIR MANUAL CORRECTION FOR THE HEADLIGHT AND TAILLIGHT SYSTEM (BODY ELECTRICAL) 00400-RM809-U2. *TT 00400-RM682-U2 - '00 TUNDRA. *TT
4576
Service Bulletin/Repair Instructions
'00 TUNDRA REPAIR MANUAL CORRECTION FOR THE TORQUE CONVERTER CLUTCH AND DRIVE PLATE - AUTOMATIC TRANSMISSION (A340E, A340F). 00400-RM682-U1. *TT
00305
Service Bulletin/Repair Instructions
ABNORMAL SQUEAL NOISE FROM THE ENGINE ACCESSORY DRIVE BELT AREA, USUALLY DURING COLD START-UP. AN IMPROVED 2UZ-FE ACCESSORY DRIVE BELT HAS BEEN DEVELOPED TO CORRECT THIS CONDITION. *TT
00105
Service Bulletin/Repair Instructions
FRONT WINDOW RATTLE. *TT
03704
Service Bulletin/Repair Instructions
ENGINE BANK 1 AND BANK 2 A/F AND 02 IDENTIFICATION. VARIOUS TOYOTA MODELS. *TT
00404
Service Bulletin/Repair Instructions
THE AIR CONDITIONING SYSTEM DOES NOT SUFFICIENTLY COOL THE CABIN. *TT
04006
Service Bulletin/Repair Instructions
CUSTOMER SUPPORT PROGRAM - WARRANTY COVERAGE ENHANCEMENT ON TWO OXYGEN SENSORS. *TT
01703
Service Bulletin/Repair Instructions
OIL PRESSURE GAUGE READS ABNORMALLY LOW AT IDLE. *TT
BR00402
Service Bulletin/Repair Instructions
INFORMATION ON FRONT BRAKE VIBRATION. REVISED. *TT
PG00503
Service Bulletin/Repair Instructions
SPARE TIRE CARRIER OPERATION. VARIOUS MODLELS INCLUDING THE 2004 LANDCRUISER AND 4 RUNNER. *TT
AX00403
Service Bulletin/Repair Instructions
ACCESSORY HOOD PROTECTOR. *TT
DL00203
Service Bulletin/Repair Instructions
REAR AXLE SEAL DESIGN CHANGE. *TT
00603
Service Bulletin/Repair Instructions
OIL PRESSURE GAUGE READS ABNORMALLY LOW AT IDLE. 2000 - 2003 SEQUOIA AND TUNDRA. *TT *JB
00103
Service Bulletin/Repair Instructions
FRONT BRAKE COMPONENT IDENTIFICATION. 2000 - CURRENT TUNDRA AND 2001 - CURRENT SEQUOIA. *TT
00102
Service Bulletin/Repair Instructions
TOYOTA RACING DEVELOPMENT (TRD) HIGH-PERFORMANCE BRAKE PADS. *TT
01902
Service Bulletin/Repair Instructions
MALFUNCTION INDICATOR LAMP (MIL) ON WITH DIAGNOSTIC TROUBLE CODE (DTC) P0135 AND / OR P0155 IN THE ENGINE CONTROL MODULE (ECM). *TT
01902R
Service Bulletin/Repair Instructions
MALFUNCTION INDICATOR LAMP (MIL) ON WITH DIAGNOSTIC TROUBLE CODE (DTC) P0135 AND / OR P0155 IN THE ENGINE CONTROL MODULE (ECM). REVISED. *TT
092302
Service Bulletin/Repair Instructions
SUBJECT REGARDING FRONT BRAKE REPAIR SERVICE TIPS. *TT
00402
Service Bulletin/Repair Instructions
FRONT BRAKE VIBRATION. *MJ *SC
BR00302
Service Bulletin/Repair Instructions
INFORMATION ON REAR BRAKE VIBRATION. *TT
EG01602
Service Bulletin/Repair Instructions
SOME VEHICLES MAY EXHIBIT AN ENGINE NO START CONDITION. *TT
SSCY01
Service Bulletin/Repair Instructions
SUBJECT REGARDING SPECIAL SERVICE CAMPAIGN Y01 STOP LAMP REMINDER. *TT
BO00602
Service Bulletin/Repair Instructions
SUBJECT REGARDING FRONT SEAT COVER DAMAGE. *SLC
TC01028
Service Bulletin/Repair Instructions
SUBJECT REGARDING ENGINE OIL DIPSTICK REPLACEMENT. *YD
EL00901
Service Bulletin/Repair Instructions
SUBJECT REGARDING TEMPERATURE GAUGE INACCURATE. *YD
TC01021
Service Bulletin/Repair Instructions
INFORMATION REGARDING TRAILER TOWING WIRE HARNESS CONVERTER REPLACEMENT.*JB
BO01901
Service Bulletin/Repair Instructions
INFORMATION REGARDING SHOULDER BELT ANCHOR TAPE SET. *JB
060601
Service Bulletin/Repair Instructions
SOME VEHICLES MAY EXPERIENCE ANTENNA MAST DURABILITY. *ET
AU00201
Service Bulletin/Repair Instructions
SOME VEHICLES MAY EXPERIENCE A LOOSE ANTENNA MAST DUE TO THE BREAKAGE OF THE ANTENNA HOLDER. *JB
T-PG007-01
Service Bulletin/Repair Instructions
Replacement vin plates.
BR00101
Service Bulletin/Repair Instructions
INFORMATION ON NEW PARKING BRAKE STRUTS TO REDUCE THE POSSIBILITY OF REAR BRAKE VIBRATION. *TT
BR00600
Service Bulletin/Repair Instructions
THIS BULLETIN INTRODUCES THE NEW PARKING BRAKE STRUTS DEVELOPED TO REDUCE THE POSSIBILITY OF REAR BRAKE VIBRATION. *TT
NV01700
Service Bulletin/Repair Instructions
THIS BULLETIN ADDRESSES NOISE CONCERNS AND DOOR CHECK PERFORMANCE ON THE FRONT DOORS. SOME CUSTOMERS MAY COMPLAIN OF A CLICK OR CREAK NOISE WHILE OPENING AND CLOSING THE DOORS. THE SERVICE TIP IN THIS BULLETIN WILL ADDRESS THE CLICK NOISE. *TT
306
Service Bulletin/Repair Instructions
BRIEF INFORMATION REGARDING THE TRAILER TOWING WIRE HARNESS POWER CONVERTER. *TT
AX00800
Service Bulletin/Repair Instructions
SUBJECT REGARDING TRAILER TOWING WIRE HARNESS POWER CONVERTER. *JB
286
Service Bulletin/Repair Instructions
SUBJECT REGARDING REVISED COOLANT HOSE CLAMP. *TT
287
Service Bulletin/Repair Instructions
SUBJECT REGARDING FIELD FIX DEVELOPED TO LIMIT THE AMOUNT OF ROAD VIBRATION TRANSFERRED TO THE ARM REST OF THE 60 / 40 SPLIT BENCH SEAT ON CERTAIN 2000 MODEL YEAR VEHICLES. *TT
EG00700
Service Bulletin/Repair Instructions
SUBJECT REGARDING REVISED COOLANT HOSE CLAMP. *JB
NV01400
Service Bulletin/Repair Instructions
THIS BULLETIN IS A FIELD FIX DEVELOPED TO LIMIT THE AMOUNT OF ROAD VIBRATION TRANSFERRED TO THE ARM REST. *JB
EG00300
Service Bulletin/Repair Instructions
SOME VEHICLES WITHIN VIN 5TB****1*YS030022 MAY EXPERIENCE A SLIGHT COOLANT LEAK FROM THE COOLANT OVERFLOW RESERVOIR VENT UNDER ROUGH DRIVING CONDITIONS. *MR
001404
Service Bulletin/Repair Instructions
INFORMATION REGARDING THE SSC U01 2000 MODELYEAR STOP LAMP. *TT
117
Service Bulletin/Repair Instructions
ELECTRONIC MESSAGE REGARDING ROOM (DOME) LAMP LENGS MODIFICATION. *TT
BO01300
Service Bulletin/Repair Instructions
SUBJECT REGARDING ROOM (DOME) LAMP LENS MODIFICATION FOR VEHICLES STARTING WITH VIN 5TBBT4416YS032558. *TT
00300
Service Bulletin/Repair Instructions
INFORMATION INTRODUCING NEW FRONT BRAKE PAD KITS TO REDUCE FRONT BRAKE VIBRATION. *TT UPDATE. *TT
PG02699
Service Bulletin/Repair Instructions
INSTALLATION OF FRONT LICENSE PLATE. *TT
DL00199
Service Bulletin/Repair Instructions
THIS BULLETIN PROVIDES THE LOCATION OF THE GREASE FITTINGS FOR THE PROPELLER SHAFT JOINTS AS WELL AS THE TYPE OF GREASE TO USE WITH EACH FITTING LOCATION. *TT
ST00299
Service Bulletin/Repair Instructions
PROCEDURES FOR IMPROVING A STEERING FLUTTER CONDITION ON VEHICLES WITHIN CERTAIN VIN RANGES. *TT
PG01799
Service Bulletin/Repair Instructions
SUBJECT REGARDING TUNDRA SUPPLEMENTAL PRE-DELIVERY SERVICE (PDS) PROCEDURE. *TT
TC99010
Service Bulletin/Repair Instructions
TOYOTA WILL INITIATE A NEW MODEL LAUNCH QUALITY ACTIVITY TO REPLACE THE BATTERY HOLD DOWN CLAMP ON CERTAIN EARLY PRODUCTION VEHICLES. *TT
032999
Service Bulletin/Repair Instructions
SUBJECT REGARDING EXTERIOR PAINT COLORS. *TT
032499
Service Bulletin/Repair Instructions
INFORMATION REGARDING SEATBELT EXTENDERS. *TT
BO00499
Service Bulletin/Repair Instructions
TOYOTA CUSTOMERS WHO FIND IT NECESSARY TO INCREASE THE LENGTH OF THEIR SEAT BELTS MAY OBTAIN SEAT BELT EXTENDERS AT NO COST THROUGH THEIR LOCAL TOYOTA DEALER. *TT
T-PG002-91
Service Bulletin/Repair Instructions
Product general information.