Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
T-SB-0055-24 Rev2
Service Bulletin/Repair Instructions
Some 2005 – 2026 Toyota vehicles that have undergone water intrusion may exhibit a condition in which a musty odor is present. Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this Service Bulletin is to provide general guidelines and procedures for odor remediation. This Service Bulletin provides a guide on how to prepare and treat the interior of the vehicle for odor remediation. Refer to the applicable model and model year Repair Manual and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines.
T-SB-0058-23 Rev1
Service Campaign
The air conditioning dye injection tool kit has been developed to aid in identifying the location of air conditioning refrigerant leaks. The procedures outlined in this Service Bulletin aid in locating, inspecting, and repairing refrigerant leaks.
T-SB-0035-24 Rev2
Service Bulletin/Repair Instructions
Acid rain results from rainwater or other airborne moisture that become acidic due to industrial chemical impurities in the atmosphere. If these acidic compounds settle on an exposed vehicle, especially the horizontal areas such as the hood, roof, and decklid, significant damage to the painted surfaces can occur. Acid rain damage can typically be identified on vehicles by the presence of stains on the paint surface that resemble hard water spots. Unlike water spots however, acid rain damage cannot be removed by regular washing procedures. Also, because acid rain can etch and soften the paint, normal buffing or polishing repair procedures should not be attempted. This can cause further damage and result in visible depressions in the paint surface. The following are the three major categories of acid rain damage: •Minor damage: requires only buffing to repair. •Moderate damage: usually requires neutralizing, color sanding, and buffing. •Severe damage: extending beyond 1/2 mil of clearcoat on a pearl, metallic, or solid color, requires neutralization, sanding, and repainting. In cases where acid rain damage is minor, neutralization and buffing with a liquid-type paint finessing product may provide an adequate repair. Only specially formulated products outlined in this bulletin should be used for that purpose. Unfortunately, other than minor damage, there is no simple method of determining the actual extent (depth) of acid penetration other than color sanding a representative affected area until there is no visible etching or depressions, followed by measuring the amount of paint removed with either a magnetic or digital-type film thickness gauge. The procedures in this bulletin are intended for use by qualified body/paint technicians and should not be attempted by inexperienced personnel. It is the dealer’s responsibility to protect and maintain the quality of the vehicle’s paint finish after receipt at the dealership prior to the first sale. Perform frequent vehicle washing, as often as daily, during high heat and humidity periods to minimize the potential for paint damage due to acid rain exposure. This is especially important in geographical areas known for high frequency and concentration of acid rain and industrial fallout.
T-SB-0038-24 Rev2
Service Bulletin/Repair Instructions
To prevent brake rotor rust from forming during transportation and storage, wheel film will be used instead of a cardboard type of anti-rust cover. The purpose of the wheel film is to shield the disc brake rotor from weather elements and initial rust before the vehicle is delivered to the customer. Consequently, the film should remain on the wheel for as long as possible.
T-SB-0039-24 Rev2
Service Bulletin/Repair Instructions
The condition known as acid rain is caused by airborne chemicals or particles in the atmosphere, which mix with rainwater, nighttime dew, or high humidity to form acidic compounds. If these contaminants settle and remain on a painted vehicle surface, especially the horizonal areas of the hood, roof, and decklid, significant damage can occur. This damage is the result of actual etching of the paint and appears as pitting or water spots. As acid rain droplets on the vehicle surface evaporate, the concentration strength of the acid increases, causing deeper and more rapid damage. This evaporation and corrosive action also occur more rapidly on dark colored cars as direct sun heat increases. It is the dealer’s responsibility to protect and maintain the quality of the vehicle’s paint finish after receipt at the dealership prior to the first sale. In areas known for high frequency and/or concentration of acid rain, frequent vehicle washing during high heat or humidity periods will minimize the potential for paint damage caused by acid rain. It is further recommended that either reverse osmosis or deionized water be used to prevent water spotting.
T-SB-0061-23 Rev2
Service Bulletin/Repair Instructions
Toyota vehicles are currently protected with RapgardTM protective film designed to protect the horizontal painted surfaces. This material protects from acid rain, environmental fallout, and rail contamination. Follow the Removal Procedure in this bulletin to remove the RapgardTM protective film within 90 days from initial application.
T-SB-0062-23 Rev2
Service Bulletin/Repair Instructions
Vehicles may occasionally be subjected to contamination by airborne iron particles shed from railroad tracks, train wheels, exposure to heavy machinery facilities, grinding, welding, etc. This type of contamination can be identified by the presence of small, red or brown particles on the paint surface. These particles are often difficult to see on dark color paints but can be easily felt when brushing a hand across horizontal body surfaces such as the hood, roof, or deck lid. Follow the Repair Procedure in this bulletin to clean vehicles that may have been subjected to contamination by airborne iron particles such as rail dust during rail transportation or extended storage near industrial areas.
T-SB-0055-24 Rev1
Service Bulletin/Repair Instructions
Some 2005 – 2024 Toyota vehicles that have undergone water intrusion may exhibit a condition in which a musty odor is present. Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this Service Bulletin is to provide general guidelines and procedures for odor remediation. This Service Bulletin provides a guide on how to prepare and treat the interior of the vehicle for odor remediation. Refer to the applicable model and model year Repair Manual and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines. This Service Bulletin is to provide a general overview and direction for the odor remediation process.
T-SB-0035-24 Rev1
Service Bulletin/Repair Instructions
Acid rain results from rainwater or other airborne moisture that become acidic due to industrial chemical impurities in the atmosphere. If these acidic compounds settle on an exposed vehicle, especially the horizontal areas such as the hood, roof, and decklid, significant damage to the painted surfaces can occur. Acid rain damage can typically be identified on vehicles by the presence of stains on the paint surface that resemble hard water spots. Unlike water spots however, acid rain damage cannot be removed by regular washing procedures. Also, because acid rain can etch and soften the paint, normal buffing or polishing repair procedures should not be attempted. This can cause further damage and result in visible depressions in the paint surface. The following are the three major categories of acid rain damage: •Minor damage: requires only buffing to repair. •Moderate damage: usually requires neutralizing, color sanding, and buffing. •Severe damage: extending beyond 1/2 mil of clearcoat on a pearl, metallic, or solid color, requires neutralization, sanding, and repainting. In cases where acid rain damage is minor, neutralization and buffing with a liquid-type paint finessing product may provide an adequate repair. Only specially formulated products outlined in this bulletin should be used for that purpose. Unfortunately, other than minor damage, there is no simple method of determining the actual extent (depth) of acid penetration other than color sanding a representative affected area until there is no visible etching or depressions, followed by measuring the amount of paint removed with either a magnetic or digital-type film thickness gauge. The procedures in this bulletin are intended for use by qualified body/paint technicians and should not be attempted by inexperienced personnel. It is the dealer’s responsibility to protect and maintain the quality of the vehicle’s paint finish after receipt at the dealership prior to the first sale. Perform frequent vehicle washing, as often as daily, during high heat and humidity periods to minimize the potential for paint damage due to acid rain exposure. This is especially important in geographical areas known for high frequency and concentration of acid rain and industrial fallout.
T-SB-0038-24 Rev1
Service Bulletin/Repair Instructions
To prevent brake rotor rust from forming during transportation and storage, wheel film will be used instead of a cardboard type of anti-rust cover. The purpose of the wheel film is to shield the disc brake rotor from weather elements and initial rust before the vehicle is delivered to the customer. Consequently, the film should remain on the wheel for as long as possible.
T-SB-0039-24 Rev1
Service Bulletin/Repair Instructions
The condition known as acid rain is caused by airborne chemicals or particles in the atmosphere, which mix with rainwater, nighttime dew, or high humidity to form acidic compounds. If these contaminants settle and remain on a painted vehicle surface, especially the horizonal areas of the hood, roof, and decklid, significant damage can occur. This damage is the result of actual etching of the paint and appears as pitting or water spots. As acid rain droplets on the vehicle surface evaporate, the concentration strength of the acid increases, causing deeper and more rapid damage. This evaporation and corrosive action also occur more rapidly on dark colored cars as direct sun heat increases. It is the dealer’s responsibility to protect and maintain the quality of the vehicle’s paint finish after receipt at the dealership prior to the first sale. In areas known for high frequency and/or concentration of acid rain (see Figure 1), frequent vehicle washing during high heat or humidity periods will minimize the potential for paint damage caused by acid rain. It is further recommended that either reverse osmosis or deionized water be used to prevent water spotting.
T-SB-0055-24
Service Bulletin/Repair Instructions
Some 2005 – 2024 Toyota vehicles that have undergone water intrusion may exhibit a condition in which a musty odor is present. Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this Service Bulletin is to provide general guidelines and procedures for odor remediation. This Service Bulletin provides a guide on how to prepare and treat the interior of the vehicle for odor remediation. Refer to the applicable model and model year Repair Manual and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines.
T-SB-0103-20 Rev1
Service Bulletin/Repair Instructions
This Service Bulletin provides updated non-electric water pump leak inspection and diagnostic tips for some 2008 – 2025 model year Toyota vehicles.
T-SB-0061-23 Rev1
Service Bulletin/Repair Instructions
Toyota vehicles are currently protected with RapgardTM protective film designed to protect the horizontal painted surfaces. This material protects from acid rain, environmental fallout, and rail contamination.
T-SB-0062-23 Rev1
Service Bulletin/Repair Instructions
Vehicles may occasionally be subjected to contamination by airborne iron particles shed from railroad tracks, train wheels, exposure to heavy machinery facilities, grinding, welding, etc. This type of contamination can be identified by the presence of small, red or brown particles on the paint surface. These particles are often difficult to see on dark color paints but can be easily felt when brushing a hand across horizontal body surfaces such as the hood, roof, or deck lid.
T-SB-0035-24
Service Bulletin/Repair Instructions
Acid rain results from rainwater or other airborne moisture that become acidic due to industrial chemical impurities in the atmosphere. If these acidic compounds settle on an exposed vehicle, especially the horizontal areas such as the hood, roof, and decklid, significant damage to the painted surfaces can occur. Acid rain damage can typically be identified on vehicles by the presence of stains on the paint surface that resemble hard water spots. Unlike water spots however, acid rain damage cannot be removed by regular washing procedures. Also, because acid rain can etch and soften the paint, normal buffing or polishing repair procedures should not be attempted. This can cause further damage and result in visible depressions in the paint surface. The following are the three major categories of acid rain damage: •Minor damage: requires only buffing to repair. •Moderate damage: usually requires neutralizing, color sanding, and buffing. •Severe damage: extending beyond 1/2 mil of clearcoat on a pearl, metallic, or solid color, requires neutralization, sanding, and repainting. In cases where acid rain damage is minor, neutralization and buffing with a liquid-type paint finessing product may provide an adequate repair. Only specially formulated products outlined in this bulletin should be used for that purpose. Unfortunately, other than minor damage, there is no simple method of determining the actual extent (depth) of acid penetration other than color sanding a representative affected area until there is no visible etching or depressions, followed by measuring the amount of paint removed with either a magnetic or digital-type film thickness gauge. The procedures in this bulletin are intended for use by qualified body/paint technicians and should not be attempted by inexperienced personnel. While the quality and durability of paint on Toyota vehicles is continuously being improved, it remains the dealer’s responsibility to protect and maintain the quality of the vehicle’s paint finish after receipt at the dealership prior to the first sale. To read, While the quality and durability of paint on Toyota vehicles is continuously being improved, it remains the dealer’s responsibility to protect and maintain the quality of the vehicle’s paint finish after receipt at the dealership prior to first sale. Perform frequent vehicle washing, as often as daily, during high heat and humidity periods to minimize the potential for paint damage due to acid rain exposure. This is especially important in geographical areas known for high frequency and concentration of acid rain and industrial fallout.
T-SB-0038-24
Service Bulletin/Repair Instructions
To prevent brake rotor rust from forming during transportation and storage, wheel film will be used instead of a cardboard type of anti-rust cover. The purpose of the wheel film is to shield the disc brake rotor from weather elements and initial rust before the vehicle is delivered to the customer. Consequently, the film should remain on the wheel for as long as possible. SUPERSESSION NOTICE The information contained in this bulletin supersedes Service Bulletin No. PD017-04. •The entire bulletin has been updated.
T-SB-0039-24
Service Bulletin/Repair Instructions
The condition known as acid rain is caused by airborne chemicals or particles in the atmosphere, which mix with rainwater, nighttime dew, or high humidity to form acidic compounds. If these contaminants settle and remain on a painted vehicle surface, especially the horizonal areas of the hood, roof, and decklid, significant damage can occur. This damage is the result of actual etching of the paint and appears as pitting or water spots. As acid rain droplets on the vehicle surface evaporate, the concentration strength of the acid increases, causing deeper and more rapid damage. This evaporation and corrosive action also occur more rapidly on dark colored cars as direct sun heat increases. While Toyota paint quality, durability, and resistance to environmental factors is continuously being improved, it remains the responsibility of the dealer to protect and maintain the vehicle’s paint finish from the time of arrival at the dealership until retail delivery to the customer. In areas known for high frequency and/or concentration of acid rain (see Figure 1), frequent vehicle washing during high heat or humidity periods will minimize the potential for paint damage caused by acid rain. It is further recommended that either reverse osmosis or deionized water be used to prevent water spotting.
T-PANT-2024-004-
Service Bulletin/Repair Instructions
This is to advise of various price adjustments that will affect Toyota Genuine Motor Oil and Long Life Coolant, effective March 1, 2024. These products are ordered through the Toyota Complete Maintenance Care (TCMC) website.
T-SB-0043-14
Service Bulletin/Repair Instructions
OBSOLETE NOTICE January 22, 2024: This bulletin is now obsolete. Please see T-SB-0057-18.
TSB005823
Service Bulletin/Repair Instructions
TSB: The air conditioning dye injection tool kit has been developed to aid in identifying the location of air conditioning refrigerant leaks. Follow the procedures outlined in this service bulletin to aid in locating, inspecting, and repairing refrigerant leaks
TSB003220
Service Bulletin/Repair Instructions
TSB: Replacement certification labels (the vinyl label installed on the driver door or door post) and VIN plates (the metal plate riveted to dashboard) (see Figure 1) for most 1979 ? 2023 model year vehicles may be available provided the requests meet the criteria listed in this Service Bulletin. Follow the Procurement Procedure in this bulletin to request a replacement certification label or VIN plate.
T-SB-0057-18
Service Bulletin/Repair Instructions
TSB: The Immobilizer and Smart Key Reset is a feature that allows the registration of new keys when all master keys are lost. Once the system is reset, all previously registered keys will be erased. Follow the procedures in this bulletin to reset a vehicle Immobilizer or Smart Key system.
T-SB-0094-21 Rev
Service Bulletin/Repair Instructions
TSB: Some 2005 ? 2022 model year Toyota vehicles that have undergone water intrusion may exhibit a condition in which a musty smell is present. Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this service bulletin is to provide general guidelines and procedures for odor remediation. This service bulletin provides a guide on how to prepare the interior of the vehicle prior to an odor remediation being performed, as well as contact information for an approved vendor who will arrange the remediation, and instructions on how to prepare the interior of the vehicle for reassembly once the remediation has been completed. Refer to all model and model year specific Repair Manuals and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines. This service bulletin is to provide a general overview and direction for the odor remediation process.
TSB001221Rev2
Service Bulletin/Repair Instructions
TSB: Some 2010 ? 2022 model year Toyota vehicles may exhibit paint stains after the removal of Rapgard?. The paint stains may appear to be under the clear coat but are usually under wrinkles in the Rapgard?. The wrinkles may trap water and cause the paint to stain from the trapped moisture, especially on horizontal surfaces such as the hood, roof, and trunk. Follow the Repair Procedure in this bulletin to address this condition
TSB009421Rev1
Service Bulletin/Repair Instructions
TSB: Some 2005 ? 2022 model year Toyota vehicles that have undergone water intrusion may exhibit a condition in which a musty smell is present. Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this service bulletin is to provide general guidelines and procedures for odor remediation. This service bulletin provides a guide on how to prepare the interior of the vehicle prior to an odor remediation being performed, as well as contact information for an approved vendor who will arrange the remediation, and instructions on how to prepare the interior of the vehicle for reassembly once the remediation has been completed. Refer to all model and model year specific Repair Manuals and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines. This service bulletin is to provide a general overview and direction for the odor remediation process
TTT063620
Service Bulletin/Repair Instructions
TT: Some Toyota vehicles installed with Toyota Complete Maintenance Care (TCMC) brake pads may exhibit a groan or squeak noise in various driving conditions
T-SB-0012-21 Rev
Service Bulletin/Repair Instructions
TSB: Some 2010 ? 2022 model year Toyota vehicles may exhibit paint stains after the removal of Rapgard?. The paint stains may appear to be under the clear coat but are usually under wrinkles in the Rapgard?. The wrinkles may trap water and cause the paint to stain from the trapped moisture, especially on horizontal surfaces such as the hood, roof, and trunk. Follow the Repair Procedure in this bulletin to address this condition
T-SB-0094-21
Service Bulletin/Repair Instructions
TSB: Some 2005 ? 2022 model year Toyota vehicles that have undergone water intrusion may exhibit a condition in which a musty smell is present. Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this service bulletin is to provide general guidelines and procedures for odor remediation. This service bulletin provides a guide on how to prepare the interior of the vehicle prior to an odor remediation being performed, as well as contact information for an approved vendor who will arrange the remediation, and instructions on how to prepare the interior of the vehicle for reassembly once the remediation has been completed. Refer to all model and model year specific Repair Manuals and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines. This service bulletin is to provide a general overview and direction for the odor remediation process.
T-TT-0578-19 Rev
Service Bulletin/Repair Instructions
TT: Some customers may encounter Bluetooth® connectivity concerns such as: ?Difficulty to pair the phone. ?Intermittent Bluetooth® failure to connect to the vehicle when first turning on the vehicle. ?Various Bluetooth® Audio functions are no longer functioning with customer?s phone such as ability to change the track using the steering wheel controls. These concerns can be caused by changes made on the customer?s phone. Make sure to inquire with the customer if the connectivity concerns occurred after receiving an operating system update on their phone, or if they have restored their phone data/settings recently.
Toyota PRO21-UFR
Service Bulletin/Repair Instructions
UPDATES TO THE 2014-2021 TOYOTA UNIVERSAL FLAT RATE MANUAL
T-SB-0044-16 Obs
Service Bulletin/Repair Instructions
OBSOLETE NOTICE March 08, 2021: This bulletin is now obsolete. Please see T-SB-0012-21.
Toyota Safety Re
Service Bulletin/Repair Instructions
Toyota Safety Recall and Service Campaign - Technician Certification Requirements
T-TT-0636-20 Rev
Service Bulletin/Repair Instructions
TT: Some Toyota vehicles installed with Toyota Complete Maintenance Care (TCMC) brake pads may exhibit a groan or squeak noise in various driving conditions.
T-SB-0040-08 Obs
Service Bulletin/Repair Instructions
OBSOLETE NOTICE March 08, 2021: This bulletin is now obsolete. Please see T-SB-0044-16.
T-SB-0012-21
Service Bulletin/Repair Instructions
TSB: Some 2010 ? 2021 model year Toyota vehicles may exhibit paint stains after the removal of Rapgard?. The paint stains may appear to be under the clear coat but are usually under wrinkles in the Rapgard?. The wrinkles may trap water and cause the paint to stain from the trapped moisture, especially on horizontal surfaces such as the hood, roof, and trunk. Follow the Repair Procedure in this bulletin to address this condition.
T-SB-0032-20 Rev
Service Bulletin/Repair Instructions
TSB: Replacement certification labels (the vinyl label installed on the driver door or door post) and VIN plates (the metal plate riveted to dashboard) (see Figure 1) for most 1979 ? 2021 model year vehicles may be available provided the requests meet the criteria listed in this Service Bulletin. Follow the Procurement Procedure in this bulletin to request a replacement certification label or VIN plate.
T-TT-0636-20
Service Bulletin/Repair Instructions
TT: Some Toyota vehicles installed with Toyota Complete Maintenance Care (TCMC) brake pads may exhibit a groan or squeak noise in various driving conditions.
T-TT-0628-20
Service Bulletin/Repair Instructions
TT: HVAC drain tube is found to be blocked/clogged.
T-SB-0103-20
Service Bulletin/Repair Instructions
TSB: This Service Bulletin provides updated non-electric water pump leak inspection and diagnostic tips for some 2008 ? 2021 model year Toyota vehicles.
T-TT-0570-19 Rev
Service Bulletin/Repair Instructions
TT: Some 2014-2020 model year Tundra vehicles with a TRD skid plate may exhibit a ?creaking? or ?crackling? noise coming from the lower front end. The source of this noise has been pinpointed in several cases to the TRD skid plate contacting the frame crossmember.
T-TT-0468-17 Rev
Service Bulletin/Repair Instructions
TT: HVAC drain tube is found to be blocked/clogged.
T-SB-0063-20
Service Bulletin/Repair Instructions
TSB: SUPERSESSION NOTICE The information contained in this bulletin supersedes Service Bulletin Nos. ST005-01, SU001-08, and T-SB-0391-08. The aforementioned bulletins are obsolete, and any printed versions should be discarded. Be sure to review the entire content of this service bulletin before proceeding. This Service Bulletin provides best practice procedures for vehicle pulling complaint, diagnosis, and repair for 2002 ? 2021 model year Toyota vehicles. This information supplements Repair Manual procedures when the symptoms are: ?Vehicle Pulling: The vehicle moves to the right or left when the driver holds the steering wheel while driving straight ahead without exerting steering effort. ?Steering Wheel Off Center: The vehicle travels straight, but the steering wheel is not pointed straight ahead. The vehicle is not pulling. Before repairing a vehicle pulling to one side, it is necessary to clearly identify the cause of the pulling condition. Frequently, pulling to one side is diagnosed as a wheel alignment concern. However, the actual cause may be related to the lateral force generated by the tires, vehicle damage, road crown or worn components. Performing a wheel alignment when tire force is the cause could result in the wheel alignment being set at a value outside of specifications. This could then cause other problems such as uneven tire wear, etc. A customer may notice a pull to the left when in the left lanes of travel and notice a pull to the right or no pull when traveling in the right lanes of travel on the very same section of roadway. This road crown effect is environmental and cannot be corrected with suspension adjustments or any other wheel or tire modification discussed in this bulletin.
T-SB-0391-08 Obs
Service Bulletin/Repair Instructions
TSB: OBSOLETE NOTICE June 23, 2020: This bulletin is now obsolete. Please see T-SB-0063-20.
T-SB-0304-17 Obs
Service Bulletin/Repair Instructions
TSB: OBSOLETE NOTICE April 07, 2020: This bulletin is now obsolete. Please see T-SB-0032-20. Replacement Certification Labels and VIN Plates
T-SB-0032-20
Service Bulletin/Repair Instructions
TSB: SUPERSESSION NOTICE The information contained in this bulletin supersedes Service Bulletin Nos. PG021-88, PG015-89, PG0015-90, PG002-91, PG002-93, PG005-97, PG007-01, PG007-07, PG006-01, PG004-97, T-SB-0144-08, and T-SB-0304-17. The aforementioned bulletins are obsolete, and any printed versions should be discarded. Replacement certification labels (the vinyl label installed on the driver door or door post) and VIN plates (the metal plate riveted to dashboard) (see Figure 1) for most 1979 ? 2020 model year vehicles may be available provided the requests meet the criteria listed in this Service Bulletin. Follow the Procurement Procedure in this bulletin to request a replacement certification label or VIN plate.
T-SB-0030-20
Service Bulletin/Repair Instructions
TSB: Some 2007 ? 2020 model year Tundra vehicles may exhibit corrosion or paint blistering on the front and/or rear lower door sill(s). Follow the Repair Procedure in this bulletin to address this condition.
T-SB-0142-13_Obs
Service Bulletin/Repair Instructions
OBSOLETE NOTICE February 12, 2020: This bulletin is now obsolete. Please see T-SB-0010-20.
T-SB-0010-20
Service Bulletin/Repair Instructions
TSB: Some 2004 ? 2017 model year Toyota vehicles may exhibit odors naturally occurring from the HVAC system and/or related environmental factors. Although there is no way to eliminate these odors, follow the General Procedure in this bulletin to minimize the odors experienced
T-SB-0008-20
Service Bulletin/Repair Instructions
TSB: Vehicles may display evidence of a fluid leak or fluid seep from powertrain components. This bulletin explains how to determine the differences between a fluid leak versus a fluid seep. Cases that are determined to be a ?leak? should be repaired accordingly and will be covered under warranty if applicable. Cases that are determined to be a ?seep? should be documented on the repair order and inspected at the next service interval. Follow the Repair Information in this bulletin to determine if the concern in question is a fluid leak or fluid seep and review the Repair Procedure section to address the condition. NOTE This bulletin applies to ALL powertrain fluids excluding fuel and coolant.
T-SB-0166-19_Rev
Service Bulletin/Repair Instructions
TSB: REVISION NOTICE January 23, 2020 Rev1: G1439 The Parts Information, Calibration Information, and Repair Procedure sections have been updated. SUPERSESSION NOTICE The information contained in this bulletin supersedes Service Bulletin No. T-SB-0058-13.Service Bulletin No. T-SB-0058-13 is obsolete and any printed versions should be discarded. Some 2009 ? 2018 model year Sequoia and 2009 ? 2019 model year Tundra vehicles equipped with a 3UR-FBE engine may exhibit a hard start and/or MIL ON condition with one or more of the following Diagnostic Trouble Codes (DTCs): ? DTC P0171 and/or P0174 (System Too Lean Bank 1/Bank 2) ? DTC P0172 and/or P0175 (System Too Rich Bank 1/Bank 2) ? DTC P1604 (Startability Malfunction) Techstream data list analysis may reveal negative fuel trims and an elevated alcohol density estimate relative to the vehicle?s actual fuel alcohol content. Follow the Repair Procedure in this bulletin to address these conditions.
T-SB-0058-13_Obs
Service Bulletin/Repair Instructions
TSB: OBSOLETE NOTICE December 09, 2019: This bulletin is now obsolete. Please see T-SB-0166-19.
T-SB-0166-19
Service Bulletin/Repair Instructions
TSB: SUPERSESSION NOTICE The information contained in this bulletin supersedes Service Bulletin No. T-SB-0058-13. Service Bulletin No. T-SB-0058-13 is obsolete and any printed versions should be discarded. Some 2009 ? 2018 model year Sequoia and 2009 ? 2019 model year Tundra vehicles equipped with a 3UR-FBE engine may exhibit a hard start and/or MIL ON condition with one or more of the following Diagnostic Trouble Codes (DTCs). ? DTC P0171 and/or P0174 (System Too Lean Bank 1/Bank 2) ? DTC P0172 and/or P0175 (System Too Rich Bank 1/Bank 2) ? DTC P1604 (Startability Malfunction) Techstream Data List analysis may reveal negative fuel trims and an elevated alcohol density estimate relative to the vehicle?s actual fuel alcohol content. Follow the Repair Procedure in this bulletin to address this condition.
T-SB-0144-19_Rev
Service Bulletin/Repair Instructions
TSB: REVISION NOTICE November 05, 2019 Rev1: ? The Warranty Information section has been updated. Any previous printed versions of this bulletin should be discarded. Some 2007 ? 2020 model year Tundra vehicles may exhibit surface corrosion and/or perforation corrosion on the back of the cab near the lower corner(s) of the center stop lamp assembly. Follow the Repair Procedure in this bulletin to address this condition.
T-SB-0150-19
Service Bulletin/Repair Instructions
TBS: Some 2007 ? 2020 model year Tundra (Crew Max) vehicles may exhibit a rust or perforation condition on the vehicle?s body behind the back window moulding. Follow the Repair Procedure in this bulletin to address this condition.
T-TT-0578-19
Service Bulletin/Repair Instructions
TT: Some customers may encounter Bluetooth® connectivity concerns such as: ? Difficulty to pair the phone. ? Intermittent Bluetooth® failure to connect to the vehicle when first turning on the vehicle. ? Various Bluetooth® Audio functions are no longer functioning with customer?s phone such as ability to change the track using the steering wheel controls. These concerns can be caused by changes made on the customer?s phone. Make sure to inquire with the customer if the connectivity concerns occurred after receiving an operating system update on their phone, or if they have restored their phone data/settings recently.
T-SB-0144-19
Service Bulletin/Repair Instructions
TSB: Some 2007 ? 2020 model year Tundra vehicles may exhibit surface corrosion and/or perforation corrosion on the back of the cab near the lower corner(s) of the center stop lamp assembly. Follow the Repair Procedure in this bulletin to address this condition
T-TT-0574-19
Service Bulletin/Repair Instructions
TT: Some customers may experience poor outgoing Bluetooth sound quality, this can occur for various reasons. Current multimedia systems are designed with the ability to adjust Bluetooth sound quality to compensate for echo or excessive background noise.
T-TT-0570-19
Service Bulletin/Repair Instructions
TT: Some 2014-2020 Tundra vehicles with a TRD skid plate may exhibit a ?creaking? or ?crackling? noise coming from the lower front end. The source of this noise has been pinpointed in several cases to the TRD skid plate contacting the frame crossmember.
T-SB-0076-19
Service Bulletin/Repair Instructions
TSB: Some 2009 ? 2019 model year Toyota vehicles with super chrome wheel finishes may become discolored and/or damaged when aftermarket cleaners, polishes, or brake dust removal products are used on wheels with super chrome finishes. Wheel cleaners and polish that contain acidic substances may damage the clear coat of the wheel, resulting in the undercoating (black) to become visible.
T-SB-0134-16-Rev
Service Bulletin/Repair Instructions
TSB: REVISION NOTICE July 01, 2019 Rev2: ? Applicability has been updated to 2019 ? 2020 model year Toyota vehicles. ? The Techstream Preparation and Process Overview sections have been updated. October 30, 2017 Rev1: ? Applicability has been updated to include 2018 model year vehicles. Any previous printed versions of this bulletin should be discarded. SUPERSESSION NOTICE The information contained in this bulletin supersedes SB No. T-SB-0012-13. Service Bulletin No. T-SB-0012-13 is obsolete and any printed versions should be discarded. Be sure to review the entire content of this bulletin before proceeding. Flash reprogramming allows the Electronic Control Unit (ECU) software to be updated without replacing the ECU. Flash calibration updates for specific vehicle models/ECUs are released as field-fix procedures described in individual Service Bulletins. This bulletin details the Techstream ECU flash reprogramming process and outlines use of the Technical Information System (TIS) and the Calibration Update Wizard (CUW). Flash calibration updates can only be applied to the vehicle/ECU combination for which they are intended. ECUs have internal security that will not allow them to be programmed with another ECU?s information. NOTE ECU is a Toyota term used to describe integrated computerized devices responsible for managing the operation of a system or subsystem. For the purposes of this bulletin, the term ?ECU? is used as a generic label for the following SAE J1930 standard references: ? Powertrain Control Module (PCM) ? Engine Control Module (ECM) ? Transmission Control Module (TCM) ? Any other Toyota specific control unit
T-TT-0414-16-Rev
Service Bulletin/Repair Instructions
TT: Some customers may encounter Bluetooth® connectivity concerns such as: ? Difficulty to pair the phone. ? Intermittent Bluetooth® failure to connect to the vehicle when first turning on the vehicle. ? Various Bluetooth® Audio functions are no longer functioning with customer?s phone such as ability to change the track using the steering wheel controls. These concerns can be caused by changes made on the customer?s phone. Make sure to inquire with the customer if the connectivity concerns occurred after receiving an operating system update on their phone, or if they have restored their phone data/settings recently.
T-TT-0468-17-Rev
Service Bulletin/Repair Instructions
TT: HVAC drain tube is found to be blocked/clogged.
T-SB-0044-16_Rev
Service Bulletin/Repair Instructions
TSB: REVISION NOTICE February 7, 2019 Rev2: * Applicability has been updated to include 2010 - 2014 model year Matrix, 2017 - 2019 model year C-HR, 2019 model year Corolla Hatchback, and 2018 - 2019 model year Toyota vehicles. G418 The Introduction and Repair Procedure sections have been updated. March 7, 2017 Rev1: * Applicability has been updated to include 2017 model year Toyota vehicles. Any previous printed versions of this bulletin should be discarded. SUPERSESSION NOTICE The information contained in this bulletin supersedes SB No. T-SB-0040-08. * Applicability has been updated to include applicable 2016 model year vehicles. Service Bulletin No. T-SB-0040-08 is obsolete and any printed versions should be discarded. Some 2010 - 2019 model year Toyota vehicles may exhibit paint stains after the removal of Rapgard. The paint stains may appear to be under the clear coat but are usually under wrinkles in the Rapgard. The wrinkles may trap water and cause the paint to stain from the trapped moisture, especially on horizontal surfaces, such as the hood, roof, and trunk. Follow the Repair Procedure in this bulletin to address this condition.
PG004-97-Obsolet
Service Bulletin/Repair Instructions
Technical Service Bulletin: OBSOLETE NOTICE: July 31, 2018: This bulletin is now obsolete. Please see T-SB-0304-17.
PG006-01-Obsolet
Service Bulletin/Repair Instructions
Technical Service Bulletin: OBSOLETE NOTICE: July 31, 2018: This bulletin is now obsolete. Please see T-SB-0304-17.
T-SB-0304-17_Rev
Service Bulletin/Repair Instructions
TSB: REVISION NOTICE July 31, 2018 Rev2: ? The Supersession Notice has been updated. January 11, 2018 Rev1: ? The Supersession Notice has been updated. Any previous printed versions of this bulletin should be discarded. SUPERSESSION NOTICE The information contained in this bulletin supersedes Service Bulletin Nos. PG021-88, PG015-89, PG0015-90, PG002-91, PG002-93, PG005-97, PG007-01, PG007-07, PG006-01, PG004-97, and T-SB-0144-08. Service Bulletin Nos. PG021-88, PG015-89, PG0015-90, PG002-91, PG002-93, PG005-97, PG007-01, PG007-07, PG006-01, PG004-97, and T-SB-0144-08 are obsolete and any printed versions should be discarded. Vehicle replacement certification labels (the vinyl label installed on the driver door or door post) and VIN plates (the metal plate riveted to dashboard) may be available from Toyota, provided the request meets one of the criteria listed in this Service Bulletin. Replacement Certification Label and VIN Plate Criteria A replacement certification label and/or VIN plate may be requested if: ? The vehicle was in an accident and the label and/or plate is damaged or attached to a part that will be replaced during the repair. ? The label and/or plate was stolen.
ZH3_Toyota POL17
Service Bulletin/Repair Instructions
Warranty Policy Bulletin: Toyota has received a number of reports regarding the outside door handles on certain 2008-2015 model year Sequoia vehicles and on certain 2007-2015 model year Tundra vehicles. In these reports, customers have indicated that one or more of the outside door handles exhibited an abnormal feeling, dragging, or sticking when used.
T-SB-0161-16_Rev
Service Bulletin/Repair Instructions
TSB: REVISION NOTICE May 18, 2018 Rev1: * Applicability has been updated to include 2018 model year Tundra and 2017 - 2018 model year Sequoia vehicles. * The entire bulletin has been updated. Any previous printed versions of this bulletin should be discarded. Some 2008 - 2018 model year Sequoia and 2007 - 2018 model year Tundra vehicles may exhibit a popping noise during RH or LH front door operation. This noise may be due to a fracture/crack in the plastic over mold of the door check arm by the pivot area. Follow the Repair Procedure in this bulletin to address this condition. NOTE If the vehicle is being repaired due to damage from an accident, this Service Bulletin and the part numbers listed do NOT apply.
T-SB-0187-12_Rev
Service Bulletin/Repair Instructions
TSB: REVISION NOTICE February 12, 2018 Rev2: ? Applicability has been updated to include 2015 ? 2018 model year vehicles. January 23, 2014 Rev1: ? Applicability has been updated to include 2013 ? 2014 model year vehicles. Any previous printed versions of this bulletin should be discarded. Toyota vehicles are equipped with either conventional or run-flat tires. Sometimes punctures may occur as a result of contact with road debris or other hazards. If a puncture occurs, it may be possible to repair the tire and return it to service. With a conventional tire it is not possible to drive for an extended amount of time with the tire at low pressures as damage to the tire may occur. With run-flat tires, due to reinforced sidewalls, it is possible to drive for up to 100 miles at speeds less than 55 mph with little or no damage to the tire. The U.S. Tire Manufacturers Association (UTSMA) provides guidelines and recommendations for tire repair and replacement. It also provides information related to: ? Basic tire information ? Tire maintenance and safety ? Driver education, tire safety curriculum.
T-SB-0009-18
Service Bulletin/Repair Instructions
TSB: The purpose of this Service Bulletin is to elevate awareness and provide best practices for leather and synthetic leather care in Toyota vehicles. As an additional resource, if the vehicle is equipped with factory leather seats, the vehicle Owner?s Manual will highlight the importance of proper maintenance and provide guidance for care.
T-TT-0375-15_Rev
Service Bulletin/Repair Instructions
TT: For customer concerns of no or poor outgoing sound from the Bluetooth systems there are diagnostics in the repair manual which can be performed to diagnose the condition.
T-TT-0377-15_Rev
Service Bulletin/Repair Instructions
TT: Some customers may experience poor outgoing Bluetooth sound quality, this can occur for various reasons. Current multimedia systems are designed with the ability to adjust Bluetooth sound quality to compensate for Echo or excessive background noise.
T-SB-0229-12_Rev
Service Bulletin/Repair Instructions
TSB: REVISION NOTICE November 22, 2017 Rev1: ? Applicability has been updated to include 2014 ? 2018 model year vehicles. Any previous printed versions of this bulletin should be discarded. In the event that a Toyota vehicle becomes submerged in water, many components may be physically damaged. Electrical and electronic components, including wiring harnesses, are particularly susceptible to corrosion and subsequent malfunction. Although any flooding can be damaging, salt water flooding elevates the potential for abnormal conditions and may increase risks due to its highly corrosive and conductive nature. Salt residue also continues to corrode and remain conductive even after a vehicle dries. This bulletin is intended to assist with safe handling and inspection of flood damaged vehicles and to provide basic guidance on likely needed repairs.
T-TT-0463-17
Service Bulletin/Repair Instructions
T-TT: Some vehicles may exhibit an abnormal HVAC blower motor noise.
T-SB-0134-16_Rev
Service Bulletin/Repair Instructions
TSB: REVISION NOTICE October 30, 2017 Rev1: * Applicability has been updated to include 2018 model year vehicles. SUPERSESSION NOTICE The information contained in this bulletin supersedes SB No. T-SB-0012-13. Flash reprogramming allows the Electronic Control Unit (ECU) software to be updated without replacing the ECU. Flash calibration updates for specific vehicle models/ECUs are released as field-fix procedures described in individual Service Bulletins. This bulletin details the Techstream ECU flash reprogramming process and outlines use of the Technical Information System (TIS) and the Calibration Update Wizard (CUW). Flash calibration updates can only be applied to the vehicle/ECU combination for which they are intended. ECUs have internal security that will not allow them to be programmed with another ECU's information.
T-SB-0304-17
Service Bulletin/Repair Instructions
TSB: Vehicle replacement certification labels (the vinyl label installed on the driver door or door post) and VIN plates (the metal plate riveted to dashboard) may be available from Toyota, provided the request meets one of the criteria listed in this Service Bulletin.
T-TT-0339-15_Rev
Service Bulletin/Repair Instructions
TT: Some vehicles may exhibit an error message when trying to perform a radio software update: "Unable to update the software. Please try again later." If the following screen is seen; follow the directions below.
SET-TSB-17-003
Service Bulletin/Repair Instructions
REVISION- Southeast Toyota Accessory Center Console lock box procedure to identify and order key if lost. Reviside to include Additional Models and Years.
T-TT-0459-17
Service Bulletin/Repair Instructions
TT: Some customers may experience Tailgate Cable Stay slack appearance. Tailgate Cable Stays are designed to have some slack when the Tailgate does not have a load applied, this is due to Tailgate loading requirements.
T-SB-0202-17_Rev
Service Bulletin/Repair Instructions
TSB: REVISION NOTICE October 6, 2017 Rev1: ? The Parts Information and Repair Procedure sections have been updated. Some 2007 ? 2015 model year Tundra and 2008 ? 2015 model year Sequoia vehicles may exhibit an abnormal feeling, dragging, or sticking when using the outside door handle.
T-SB-0277-17
Service Bulletin/Repair Instructions
TSB: Some 2014 ? 2017 model year Tundra vehicles equipped with clearance warning sonar ultrasonic sensors mounted in metal bumpers may alert that an object is detected when no objects are in the detection area. Follow the procedure in this bulletin to address this condition.
T-SB-0218-17_Rev
Service Bulletin/Repair Instructions
TSB: REVISION NOTICE July 20, 2017 Rev1: Applicability has been updated to exclude 2007 ? 2017 model year Avanza vehicles. Some hazardous material treatment and handling regulations at the state and local level define the pre-disposal deployment of airbag and pre-tensioner assemblies as hazardous material treatment. Hazardous material treatment may require special training, certification or licensing in certain areas. TMS recommends that dealership personnel carefully review and follow ALL local and state regulations, and where necessary, contract with Environmental Protection Agency (EPA) Licensed Hazardous Waste Transportation and Disposal facilities.
ZH3-Dealer Daily
Service Bulletin/Repair Instructions
Dealer Daily Message: ZH3 Warranty Enhancement Program ? Certain 2008 - 2015 Model Year Sequoia Vehicles and Certain 2007 - 2015 Model Year Tundra Vehicles Extension of Warranty Coverage for the Outside Door Handles.
ZH3-Dealer Email
Service Bulletin/Repair Instructions
Dealer Email: Toyota is announcing a Warranty Enhancement Program to extend the warranty coverage for the outside door handles on certain 2008 ? 2015 model year Sequoia Vehicles and certain 2007 ? 2015 model year Tundra vehicles.
ZH3-Dealer Lette
Service Bulletin/Repair Instructions
Dealer Letter: Toyota has received a number of reports regarding the outside door handles on certain 2008 ? 2015 model year Sequoia vehicles and on certain 2007 ? 2015 model year Tundra vehicles. In these reports, customers have indicated that one or more of the outside door handles exhibited an abnormal feeling, dragging, or sticking when used.
ZH3-POL17-07-04.
Service Bulletin/Repair Instructions
Warranty Policy Bulletin POL17-07: Toyota has received a number of reports regarding the outside door handles on certain 2008-2015 model year Sequoia vehicles and on certain 2007-2015 model year Tundra vehicles. In these reports, customers have indicated that one or more of the outside door handles exhibited an abnormal feeling, dragging, or sticking when used.
ZH3-Region Email
Service Bulletin/Repair Instructions
Region Email: Toyota is announcing a Warranty Enhancement Program to extend the warranty coverage for the outside door handles on certain 2008 ? 2015 model year Sequoia Vehicles and certain 2007 ? 2015 model year Tundra vehicles.
ZH3-Region Lette
Service Bulletin/Repair Instructions
Region Letter: Toyota has received a number of reports regarding the outside door handles on certain 2008 ? 2015 model year Sequoia vehicles and on certain 2007 ? 2015 model year Tundra vehicles. In these reports, customers have indicated that one or more of the outside door handles exhibited an abnormal feeling, dragging, or sticking when used.
T-SB-0206-17
Service Bulletin/Repair Instructions
TSB: Some 2014-2016 model year Tundra vehicles may exhibit difficulty in adjusting seat position (forward or backward) on manual seats. This is due to the seat position adjustment lever interfering with the seat cushion. Follow the Repair Procedure in this bulletin to address this condition.
T-SB-0035-16_Rev
Service Bulletin/Repair Instructions
TSB: REVISION NOTICE March 23, 2017 Rev1: ? Applicability has been updated to include 2016 - 2017 model year Mirai vehicles. G1855ware Version Information charts and the Introduction have been updated. SUPERSESSION NOTICE: The information contained in this bulletin supersedes SB No. T-SB-0160-14. ? The Required Tools & Equipment section has been updated. Service Bulletin No. T-SB-0160-14 is Obsolete and any printed versions should be discarded.
T-SB-0202-17
Service Bulletin/Repair Instructions
TSB: Some 2007 ? 2015 Tundra and 2008 ? 2015 model year Sequoia vehicles may exhibit an abnormal feeling, dragging or sticking when using the outside door handle. Use the following procedure to address this condition.
T-TT-0437-17
Service Bulletin/Repair Instructions
TT: Some customers may experience greyed out buttons or inactive screens (lockouts) while driving. This is to promote safe driving practices and reduce the amount of distractions while driving. These lockouts can?t be deactivated or defeated through any settings. The following is a list of common lockouts, however, this is not a complete list of lockouts.
T-TT-0435-17
Service Bulletin/Repair Instructions
TT: This bulletin is regarding best practices when handling navigation systems that use Hard Disc Drive or Micro SD Card memory.
SET-TSB-17-001
Service Bulletin/Repair Instructions
Dash Appliqué A/C Control Panel Illumination
TSB018217
Service Bulletin/Repair Instructions
TSB: SUPERSESSION NOTICE The information contained in this bulletin supersedes SB No. T-SB-0101-11. Applicability has been updated to include 2016 ? 2017 model year vehicles. Service Bulletin No. T-SB-0101-11 is Obsolete and any printed versions should be discarded. Be sure to review the entire content of this bulletin before proceeding. When servicing interior electrical switches and components, please note the precautions in this bulletin to avoid damaging electrical components and switches. Many lubricants, cleaners, and automotive chemicals contain silicone or other compounds that may contaminate electrical contacts, and therefore increase electrical resistance and decrease switch performance. The use of any cleaners or fluids may increase the risk of further damage to electrical components.
T-SB-0012-13 Rev
Service Bulletin/Repair Instructions
TSB: OBSOLETE NOTICE: September 14, 2016: This bulletin is now obsolete. Please see T-SB-0134-16.
T-SB-0142-13 Rev
Service Bulletin/Repair Instructions
TSB: REVISION NOTICE November 10, 2016 Rev2: ? Applicability has been updated to include 2016 ? 2017 model year Toyota vehicles. ? Parts Information section has been updated. Some 2004 ? 2017 model year Toyota vehicles may exhibit odors naturally occurring from the HVAC system and/or related environmental factors. Although there is no way to eliminate these odors, follow the General Procedure in this bulletin to minimize the odors experienced.
T-TT-0315-14 Rev
Service Bulletin/Repair Instructions
TT: Chrometec (plastic clad) wheels are being damaged during mounting and dismounting of tires.
T-SB-0161-16
Service Bulletin/Repair Instructions
TSB: Some 2008 ? 2016 Sequoia and 2007 ? 2017 model year Tundra vehicles may exhibit a loud popping noise when operating the front doors. Noise is due to a fracture/crack in the plastic over mold of the door check arm by the pivot area. Follow the Repair Procedure in this bulletin to address this condition. NOTE If the vehicle is being repaired due to damage resulting from an accident, this Service Bulletin and part numbers listed do NOT apply. Follow normal parts order and Repair Procedures.
T-TT-0424-16
Service Bulletin/Repair Instructions
TT: Front Brake Vibration Key Points: * Issue can occur at any time if improper torque is applied on lug nuts * Over time, even one lug nut over or under torqued, can cause a vibration issue * When lug nuts are over torqued, this causes the rotor to have a runout out condition which can lead to brake vibration concerns * Brake vibration issues can occur at parking lot to highway speeds * Brake vibration issues can occur at light to moderate braking * Tightening lug nuts in a star pattern method during the torqueing process will assure that even/equal pressure is applied across the rotor hub surface * Torque sticks/wrenches should be used to apply accurate torque values when tightening * Do Not use impact guns/ratchets to completely run lug nuts up to the wheel surface
T-SB-0146-16
Service Bulletin/Repair Instructions
TSB: Some 2014 ? 2016 model year Tundra vehicles may exhibit a MIL ?ON? condition with Diagnostic Trouble Code (DTC) P2610 (ECM/PCM Engine Off Timer Performance) present. The Engine Control Module (ECM) logic has been modified to reduce the possibility of this condition. Follow the Repair Procedure below to address this condition.
T-TT-0309-14 Rev
Service Bulletin/Repair Instructions
TT: Some customers may experience Bluetooth disconnections or loss of SMS text message functionality on the navigation/audio system with Android phones running OS 4.4 or later. Condition tends to occur to customers who have many previous text messages on their phones.
T-TT-0418-16
Service Bulletin/Repair Instructions
TT: Customer may note a "creaking" or "crackling" noise coming from the lower front end. This has been attributed in several cases to the TRD front skid plate contacting the frame cross member.
T-SB-0134-16
Service Bulletin/Repair Instructions
TSB: Supersession Notice. Flash reprogramming allows the ECU software to be updated without replacing the ECU. Flash calibration updates for specific vehicle models/ECUs are released as field-fix procedures described in individual Service Bulletins. This bulletin details the Techstream ECU flash reprogramming process and outlines use of the Technical Information System (TIS) and the Calibration Update Wizard (CUW). Flash calibration updates can only be applied to the vehicle/ECU combination for which they are intended. ECUs have internal security that will not allow them to be programmed with another ECU?s information.
T-TT-0414-16
Service Bulletin/Repair Instructions
TT: Some customers may encounter Bluetooth® connectivity concerns such as: *Difficulty to pair the phone. *Intermittent Bluetooth® failure to connect to the vehicle when first turning on the vehicle. *Various Bluetooth® Audio functions are no longer functioning with customer's phone such as ability to change the track using the steering wheel controls.
Safety Recall an
Service Bulletin/Repair Instructions
Update on Technician Certification Requirements.
T-TT-0407-16
Service Bulletin/Repair Instructions
TT: When changing oil on a ?14-16? MY Tundra with an accessory skid plate (Part Number PT938-34140), there is an access panel to gain easy access to the oil drain plug and filter.
T-TT-0404-16
Service Bulletin/Repair Instructions
TT: Some 13-17MY Tundra vehicles may exhibit a vibration/pulsation during light to hard braking. The vibration/pulsation feeling can be described as being felt in any combination of the following: Steering wheel, brake pedal, seat, and entire vehicle. This condition is felt over a large range of speed, unlike drive shaft and wheel balance concerns.
T-SB-0079-16
Service Bulletin/Repair Instructions
TSB: Some 2014 ? 2016 model year Tundra (1UR-FE) vehicles may exhibit a MIL ?ON? condition with Diagnostic Trouble Code (DTC) P2440 (Secondary Air Injection System Switching Valve Stuck Open, Bank 1), or P2442 (Secondary Air Injection System Switching Valve Stuck Open, Bank 2), and under some conditions may enter limp mode (limited throttle input ~ 25mph). This condition can be triggered by sub-freezing ambient temperatures. Follow the Repair Procedure below to address this condition.
T-TT-0399-16
Service Bulletin/Repair Instructions
TT: Multimedia systems reset procedure should be performed when the multimedia system no longer responds or reboots itself.
T-SB-0047-16
Service Bulletin/Repair Instructions
TSB: The breather plug should be replaced during any differential/transfer case repairs to prevent possible repeat failures. The subsequent use of the original breather plug after a repair has been found to contribute to the failure of the differential/transfer case components. Replace the breather plug when replacing differential/transfer case components.
T-SB-0044-16
Service Bulletin/Repair Instructions
TSB: On some vehicles, when Rapgard? is removed, the paint may have a stained appearance. These stains appear to be under the clear coat (repainting this area is not necessary). The stain patterns are usually under wrinkles in the Rapgard?. These wrinkles sometimes trap water and cause the paint to stain from the trapped moisture, especially on horizontal surfaces, such as the hood, roof, and trunk. Stains can be removed by heating the stained surface to remove the trapped moisture.
T-SB-0035-16
Service Bulletin/Repair Instructions
TSB: Some 2014 model year applicable vehicles equipped with Entune? Audio (version 010169) / Entune? Audio Plus (version 010171) / Entune? Premium Audio (version 010185) may exhibit one or more of the following conditions.
T-SB-0160-14 OBS
Service Bulletin/Repair Instructions
TSB: OBSOLETE NOTICE: THIS BULLETIN IS NOW OBSOLETE. PLEASE SEE T-SB-0035-16.
T-SB-0160-14 Obs
Service Bulletin/Repair Instructions
TSB: OBSOLETE NOTICE: This bulletin is now obsolete. Please see T-SB-0035-16.
T-TT-0392-16 REV
Service Bulletin/Repair Instructions
TT: SOME CUSTOMERS MAY EXPERIENCE BLUETOOTH CONNECTION ISSUES AFTER UPDATING THE ANDROID OPERATING SYSTEM TO 5.X.X (LOLLIPOP) OR LATER.
T-TT-0392-16 Rev
Service Bulletin/Repair Instructions
TT: Some customers may experience Bluetooth connection issues after updating the Android Operating System to 5.x.x (Lollipop) or later.
T-TT-0392-16
Service Bulletin/Repair Instructions
TT: Some customers may experience Bluetooth connection issues after updating the Android Operating System to 5.x.x (Lollipop) or later.
SET-TSB-16-003
Service Bulletin/Repair Instructions
On vehicles equipped with the SET accessory Split Rear Dual Exhaust system, the
F0A_Dealer Daily
Service Bulletin/Repair Instructions
Dealer Daily Notice: In our continuing efforts to ensure the best in customer satisfaction, Toyota has turned Limited Service Campaign (LSC) F0A into Special Service Campaign (SSC) F0A with no expiration date. Toyota will be mailing a second owner letter to customers, in late April, 2016, who have not had LSC F0A completed. The second owner letter will advise the customer the program has been extended with no expiration date. Refer to the update Dealer Letter, FAQ, and Sample Owner Letter Now Available on TIS for additional information.
F0A_TI_Sequoia_P
Service Bulletin/Repair Instructions
Technical Instructions: In certain 2012 ? 2014 Model Year Toyota Tundra and Sequoia vehicles equipped with a 5.7 Liter gasoline or 5.7 Liter-Flex Fuel engines, the Engine Control Module (ECM) may set a Diagnostic Trouble Code (DTC) if debris/ice becomes lodged in the air switching valve. If this occurs, the Malfunction Indicator (Check Engine) Light could illuminate and the vehicle could enter a ?Fail-Safe? Mode (also known as ?Limp-Home? Mode). If this occurs the vehicle?s power and speed will be reduced, which could inconvenience you and require immediate repair.
F0A_Dealer Lette
Service Bulletin/Repair Instructions
Dealer Letter: In our continuing efforts to ensure the best in customer satisfaction, Toyota has turned Limited Service Campaign (LSC) F0A into Special Service Campaign (SSC) F0A with no expiration date. This SSC covers certain 2012 ? 2014 MY Tundra and Sequoia vehicles. This SSC will cover approximately 39,000 Sequoia and 247,000 Tundra vehicles equipped with a 5.7 liter gasoline or 5.7 Liter-Flex Fuel engines. In certain 2012 ? 2014 Model Year Toyota Tundra and Sequoia vehicles equipped with a 5.7 Liter gasoline or 5.7 Liter-Flex Fuel engines, the Engine Control Module (ECM) may set a Diagnostic Trouble Code (DTC) if debris/ice becomes lodged in the air switching valve. If this occurs, the Malfunction Indicator (Check Engine) Light could illuminate and the vehicle could enter a ?Fail-Safe? Mode (also known as ?Limp-Home? Mode). If this occurs the vehicle?s power and speed will be reduced, which could inconvenience you and require immediate repair.
F0A_TI_Added Cal
Service Bulletin/Repair Instructions
Technical Instructions: In certain 2012 ? 2014 Model Year Toyota Tundra and Sequoia vehicles equipped with a 5.7 Liter gasoline or 5.7 Liter-Flex Fuel engines, the Engine Control Module (ECM) may set a Diagnostic Trouble Code (DTC) if debris/ice becomes lodged in the air switching valve. If this occurs, the Malfunction Indicator (Check Engine) Light could illuminate and the vehicle could enter a ?Fail-Safe? Mode (also known as ?Limp-Home? Mode). If this occurs the vehicle?s power and speed will be reduced, which could inconvenience you and require immediate repair.
T-TT-0339-15
Service Bulletin/Repair Instructions
TT: Some vehicles may exhibit an error message when trying to perform a radio software update: "Unable to update the software. Please try again later." If the following screen is seen, follow the directions below.
SET-TSB-15-003
Service Bulletin/Repair Instructions
Southeast Toyota Accessory Remote Engine Start System may experience a Crank no start or No Crank concern accompanied by DTC B279A due to open in Remote Engine Start Harness.
T-TT-0268-13 REV
Service Bulletin/Repair Instructions
TT: SOME CUSTOMERS MAY ENCOUNTER BLUETOOTH CONNECTIVITY CONCERNS SUCH AS: DIFFICULTY PAIRING THE PHONE. INTERMITTENT BLUETOOTH FAILURE TO CONNECT WHEN FIRST TURNING ON THE VEHICLE. VARIOUS BLUETOOTH AUDIO FUNCTIONS ARE NO LONGER FUNCTIONING WITH THE CUSTOMERS PHONE, SUCH AS THE ABILITY TO CHANGE THE TRACK USING THE STEERING WHEEL CONTROLS. THESE CONCERNS CAN BE CAUSED BY CHANGES MADE ON THE CUSTOMERS PHONE. MAKE SURE TO INQUIRE WITH THE CUSTOMER IF THE CONNECTIVITY CONCERNS OCCURRED AFTER RECEIVING AN OPERATING SYSTEM UPDATE ON THEIR PHONE OR IF THEY HAVE RESTORED THEIR PHONE DATA/SETTINGS RECENTLY.
T-TT-0374-15
Service Bulletin/Repair Instructions
TT: Since MY 2011, several different update or upgrade USB SSTs have been issued for Toyota audio and navigation systems. Refer to the chart below for a comprehensive list of all current and previously issued USB SSTs and their applicability.
T-TT-0374-15 REV
Service Bulletin/Repair Instructions
TT: SINCE MY 2011, SEVERAL DIFFERENT UPDATE OR UPGRADE USB SSTS HAVE BEEN ISSUED FOR TOYOTA AUDIO AND NAVIGATION SYSTEMS. REFER TO THE CHART BELOW FOR A COMPREHENSIVE LIST OF ALL CURRENT AND PREVIOUSLY ISSUED USB SSTS AND THEIR APPLICABILITY.
TTT-0268-13 Rev3
Service Bulletin/Repair Instructions
TT: Some customers may encounter Bluetooth connectivity concerns such as: ? Difficulty pairing the phone. ? Intermittent Bluetooth failure to connect when first turning on the vehicle. ? Various Bluetooth Audio functions are no longer functioning with the customer?s phone, such as the ability to change the track using the steering wheel controls. These concerns can be caused by changes made on the customer?s phone. Make sure to inquire with the customer if the connectivity concerns occurred after receiving an operating system update on their phone or if they have restored their phone data/settings recently.
T-TT-0385-16
Service Bulletin/Repair Instructions
Tech Tip: This Tech Tip is being provided to bring attention to the new location of the Entune/NAV/Map Update and Upgrade USB Directory. Click on the TIS tab, Diagnostics tab, Telematics tab, and the document is now located under the reference documents sections. This change has occurred to help speed up the updating process of this document.
SET-TSB-15-012
Service Bulletin/Repair Instructions
Discusses customer concern of Southeast Toyota Accessory wheel chrome peeling concern and inspection of wheels.
T-TT-0381-16
Service Bulletin/Repair Instructions
Tech Tip: Some customers may experience difficulty programming HomeLink.
T-TT-0375-15
Service Bulletin/Repair Instructions
TT: For customer concerns of no or poor outgoing sound from the Bluetooth systems there are diagnostics in the repair manual which can be performed to diagnose the condition.
T-TT-0377-15
Service Bulletin/Repair Instructions
TT: Some customers may experience poor outgoing Bluetooth sound quality, this can occur for various reasons. Current multimedia systems are designed with the ability to adjust Bluetooth sound quality to compensate for Echo or excessive background noise.
T-TT-0315-14
Service Bulletin/Repair Instructions
TT: Chrometec (plastic clad) wheels are being damaged during mounting and dismounting of tires. Refer to photos below for identifying plastic and aluminum portions of wheel:
T-TT-0309-14 REV
Service Bulletin/Repair Instructions
TT: SOME CUSTOMERS MAY EXPERIENCE BLUETOOTH DISCONNECTIONS OR LOSS OF SMS TEXT MESSAGE FUNCTIONALITY ON THE NAVIGATION/AUDIO SYSTEM WITH ANDROID PHONES RUNNING OS 4.4 OR LATER. CONDITION TENDS TO OCCUR TO CUSTOMERS WHO HAVE MANY PREVIOUS TEXT MESSAGES ON THEIR PHONES.
T-SB-0092-15
Service Bulletin/Repair Instructions
TSB: Some 2014 - 2015 model year Tundra vehicles equipped with 3UR-FE engine and Supercharger may experience a MIL "ON" condition with the following Diagnostic Trouble Code (DTC): P0101 - Mass Air Flow Circuit Range/Performance Problem. Follow the procedures in this bulletin to address this condition.
F10_DEALER LETTE
Service Bulletin/Repair Instructions
DL: TOYOTA IS PROVIDING ENHANCED INSTRUCTIONS FOR THE USE AND REINSTALLATION OF THE SPARE TIRE.
F10_Dealer Lette
Service Bulletin/Repair Instructions
DL: Toyota is providing enhanced instructions for the use and reinstallation of the spare tire.
F10_PRODUCT UPDA
Service Bulletin/Repair Instructions
EC: TOYOTA IS PROVIDING ENHANCED INSTRUCTIONS FOR THE USE AND REINSTALLATION OF THE SPARE TIRE.
F10_Product Upda
Service Bulletin/Repair Instructions
EC: Toyota is providing enhanced instructions for the use and reinstallation of the spare tire.
F10_REMEDY UPDAT
Service Bulletin/Repair Instructions
RL: TOYOTA IS PROVIDING ENHANCED INSTRUCTIONS FOR THE USE AND REINSTALLATION OF THE SPARE TIRE.
F10_Remedy Updat
Service Bulletin/Repair Instructions
RL: Toyota is providing enhanced instructions for the use and reinstallation of the spare tire.
T-TT-0234-13 REV
Service Bulletin/Repair Instructions
TT: SINCE MY 2011, SEVERAL DIFFERENT UPDATE OR UPGRADE USB SSTS HAVE BEEN ISSUED FOR TOYOTA AUDIO AND NAVIGATION SYSTEMS. REFER TO THE CHART BELOW FOR A COMPREHENSIVE LIST OF ALL CURRENT AND PREVIOUSLY ISSUED USB SSTS AND THEIR APPLICABILITY.
TTT-0234-13 Rev6
Service Bulletin/Repair Instructions
TT: Since MY 2011, several different update or upgrade USB SSTs have been issued for Toyota audio and navigation systems. Refer to the chart below for a comprehensive list of all current and previously issued USB SSTs and their applicability.
T-TT-0344-15 REV
Service Bulletin/Repair Instructions
TT: IPHONE TEXT MESSAGES DO NOT APPEAR ON MULTIMEDIA DIS[PLAY.
TTT-0344-15 Rev1
Service Bulletin/Repair Instructions
TT: iPhone text messages do not appear on multimedia dis[play.
T-TT-0360-15
Service Bulletin/Repair Instructions
TT: Customers may experience connectivity issues when the following conditions are met: The customer's iPhone is operating on iOS9 firmware. The customer's iPhone is connected to the vehicle via Bluetooth. The customer may complain of the following issues: When receiving two incoming calls simultaneously, both calls are ended automatically. iTunes Radio app does not play via Bluetooth audio. Podcast and Audiobook media playback is inoperative via Bluetooth audio.
T-SB-0020-14 REV
Service Bulletin/Repair Instructions
TSB: SOME 2014 MODEL YEAR VEHICLES EQUIPPED WITH ENTUNE PREMIUM AUDIO SYSTEM MAY EXHIBIT ONE OR MORE OF THE FOLLOWING CONDITIONS: SOME POIS ARE SHOWN MULTIPLE TIMES SOME POIS CANNOT BE SEARCHED SOME ROAD NAMES AND POIS IN VOICE GUIDANCE DO NOT MATCH ACTUAL NAMES SOME CITY NAMES CANNOT BE RECOGNIZED BY VOICE COMMAND SYSTEM NAVIGATION ROUTES TO WRONG LOCATION WHEN DESTINATION IS INPUT BY ADDRESS A NEW MAP MICRO SD CARD IS NOW AVAILABLE TO ADDRESS THESE CONDITIONS.
T-SB-0020-14 Rev
Service Bulletin/Repair Instructions
TSB: Some 2014 model year vehicles equipped with Entune Premium Audio System may exhibit one or more of the following conditions: * Some POIs are shown multiple times * Some POIs cannot be searched * Some road names and POIs in voice guidance do not match actual names * Some city names cannot be recognized by Voice Command System * Navigation routes to wrong location when destination is input by address A new Map Micro SD Card is now available to address these conditions.
T-SB-0060-15
Service Bulletin/Repair Instructions
TSB: Some 2014 ? 2015 model year Tundra CrewMax vehicles equipped with the 1794 Western Package may exhibit premature wear of the leather seat cushion due to entering or exiting the vehicle. Follow the Repair Procedure in this bulletin to address this condition.
T-SB-0160-14 Rev
Service Bulletin/Repair Instructions
TSB: Some 2014 model year applicable vehicles equipped with Entune? Audio (version 010169) / Entune? Audio Plus (version 010171) Entune? Premium Audio (version 01085) may exhibit one or more of the following conditions: Bluetooth® sometimes disconnects with Android? phones Bluetooth® disconnects with iPhone® 4 when connected to USB Radio reboots with heavy radio load condition (e.g., dual map and POIs ON and Entune? Audio music ON and multiple destinations set) (Entune? Premium Audio only) Radio reboots after completing a navigation route by voice command system and pressing Talk Switch (Entune? Premium Audio only)
T-SB-0043-14 Rev
Service Bulletin/Repair Instructions
TSB: The Immobilizer and Smart Key Reset is a feature that allows the registration of new keys when all master keys are lost. Once the system is reset, all previously registered keys will be erased. Follow the procedures in this bulletin to reset a vehicle Immobilizer or Smart Key system. NOTE: There are new security provisions required to obtain a Reset Pass-Code. It is critical that the instructions for this new process are reviewed BEFORE attempting to get a Pass-Code in the new system.
T-TT-0344-15
Service Bulletin/Repair Instructions
TT: iPhone text messages do not appear on multimedia display.
T-TT-0234-13 Rev
Service Bulletin/Repair Instructions
TT: Since MY 2011, several different update or upgrade USB SSTs have been issued for Toyota audio and navigation systems. Refer to the chart below for a comprehensive list of all current and previously issued USB SSTs and their applicability.
T-SB-0025-15
Service Bulletin/Repair Instructions
TSB: While a vehicle is in inventory, the battery is subject to conditions that can reduce its performance and life. Batteries can become discharged due to an extended storage period, temperature, parasitic drain, or while demonstrating vehicle features and benefits in the sales process. Battery inspection and maintenance are required in order to ensure proper operation and optimal battery life. As described in this bulletin, operating the engine for 30 minutes after 60 days in storage and every 30 days thereafter will help to maintain battery State of Charge (SOC). This process supplements other movements of the vehicle as it is staged, and has specific restrictions on how maintenance is to be done. Also described in this bulletin are 2 other approved methods for maintaining battery State of Charge.
T-SB-0083-13 Rev
Service Bulletin/Repair Instructions
TSB: The procedure in this bulletin is a general guideline on how to properly diagnose the air conditioning system after a component failure. Refer to the applicable Repair Manual for vehicle specific repair procedures and parts.
T-SB-0022-15
Service Bulletin/Repair Instructions
TSB: Some 2014 - 2015 model year Tundra vehicles equipped with Clearance Warning Sonar AND steel bumpers may exhibit a condition where the Clearance Warning Sonar activates without an object inthe detection area. An updated sonar sensor retainer is available to address this condition.
T-TT-0337-15
Service Bulletin/Repair Instructions
TT: When updating either the navigation or radio firmware, verify the vehicle applicability BEFORE beginning the update.
T-SB-0017-15
Service Bulletin/Repair Instructions
TSB: Should removal and replacement of the upper B-pillar trim become necessary, follow the procedure in this bulletin to ensure proper installation of the upper B-pillar trim.
T-SB-0101-11 Rev
Service Bulletin/Repair Instructions
TSB: When servicing interior electrical switches and components, please note the precautions in this bulletin to avoid damaging electrical components and switches. Many lubricants, cleaners, and automotive chemicals contain silicone or other compounds that may contaminate electrical contacts, and therefore increase electrical resistance and decrease switch performance. The use of any cleaners or fluids may increase the risk of further damage to electrical components.
T-TT-0262-13 Rev
Service Bulletin/Repair Instructions
TT: Starting with 2010 Model Year, Toyota began a gradual transition to the use of synthetic 0w-20 viscosity engine oil. There are multiple benefits of this oil. Due to the them improved performance and durability of 0w-20 synthetic oil, Toyota has extended the oil change intervals to 10,000 miles for most vehicles that require this oil.
T-TT-0330-15
Service Bulletin/Repair Instructions
TT: Clock becomes inoperative, has dashes displayed, or cannot be adjusted.
TTT-0337-15 Rev1
Service Bulletin/Repair Instructions
TT: When updating either the navigation or radio firmware, verify the vehicle applicability BEFORE beginning the update.
T-TT-0268-13 Rev
Service Bulletin/Repair Instructions
TT: Some customers may encounter Bluetooth® connectivity concerns such as: * Difficulty to pair the phone. * Intermittent Bluetooth® failure to connect to the vehicle when first turning on the vehicle. * Various Bluetooth® Audio functions are no longer functioning with customer's phone such as ability to change the track using the steering wheel controls. These concerns can be caused by changes made on the customer's phone. Make sure to inquire with the customer if the connectivity concerns occurred after receiving an operating system update on their phone or if they have restored their phone data/settings recently.
T-SB-0040-08
Service Bulletin/Repair Instructions
TSB: On some vehicles, when Rapgard is removed, the paint may have a stained appearance. These stains appear to be under the clear coat (repainting this area is not necessary). The stain patterns are usually under wrinkles in the Rapgard. These wrinkles sometimes trap water and cause the paint to stain from the trapped moisture, especially on horizontal surfaces, such as the hood, roof, and trunk. Stains can be removed by heating the stained surface to remove the trapped moisture.
TT-0307-14 Rev2
Service Bulletin/Repair Instructions
TT: Some customers may encounter various Bluetooth connectivity concerns after upgrading to iOS 8.0 and later. Conditions typically experienced include inability to pair the iPhone to the system, poor sound quality during phone calls placed through the audio/navigation system, and the inability to place a hands free phone call using the audio/navigation system.
T-TT-0267-13 Rev
Service Bulletin/Repair Instructions
TT: Some vehicles equipped with Display Audio may exhibit a condition where the touch screen is inoperative.
T-SB-0001-15 Rev
Service Bulletin/Repair Instructions
TSB: Some 2013 - 2015 model year Tundra vehicles may exhibit a condition where the Roof Drip Molding may become loose and will not stay in the roof channel. A modified Roof Drip Molding is available to address this condition.
T-SB-0001-15
Service Bulletin/Repair Instructions
TSB: Some 2013 - 2015 model year Tundra vehicles may exhibit a condition where the Roof Drip Molding may become loose and will not stay in the roof channel. A modified Roof Drip Molding is available to address this condition.
T-SB-0012-13 REV
Service Bulletin/Repair Instructions
TSB: FLASH REPROGRAMMING ALLOWS THE ECU SOFTWARE TO BE UPDATED WITHOUT REPLACING THE ECU. FLASH CALIBRATION UPDATES FOR SPECIFIC VEHICLE MODELS/ECUS ARE RELEASED AS FIELD-FIX PROCEDURES DESCRIBED IN INDIVIDUAL SERVICE BULLETINS. THIS BULLETIN DETAILS THE TECHSTREAM ECU FLASH REPROGRAMMING PROCESS AND OUTLINES USE OF THE TECHNICAL INFORMATION SYSTEM (TIS) AND THE CALIBRATION UPDATE WIZARD (CUW). FLASH CALIBRATION UPDATES CAN ONLY BE APPLIED TO THE VEHICLE/ECU COMBINATION FOR WHICH THEY ARE INTENDED. ECUS HAVE INTERNAL SECURITY THAT WILL NOT ALLOW THEM TO BE PROGRAMMED WITH ANOTHER ECUS INFORMATION.
TSB-0012-13 Rev2
Service Bulletin/Repair Instructions
TSB: Flash reprogramming allows the ECU software to be updated without replacing the ECU. Flash calibration updates for specific vehicle models/ECUs are released as field-fix procedures described in individual Service Bulletins. This bulletin details the Techstream ECU flash reprogramming process and outlines use of the Technical Information System (TIS) and the Calibration Update Wizard (CUW). Flash calibration updates can only be applied to the vehicle/ECU combination for which they are intended. ECUs have internal security that will not allow them to be programmed with another ECU?s information.
T-TT-307-14 Rev1
Service Bulletin/Repair Instructions
TT: Customers complain of various Bluetooth connectivity concerns after upgrading to iOS 8.0 and later. Conditions typically experienced include inability to pair the iPhone to the system, poor sound quality during phone calls placed through the audio/navigation system, and the inability to place a hands free phone call using the audio/navigation system.
F0A_LSC_Dealer D
Service Bulletin/Repair Instructions
Dealer Daily: In our continuing effort to ensure the best in customer satisfaction, Toyota is launching a Limited Service Campaign (LSC) on certain 2012 - 2014 MY Tundra and Sequoia vehicles. This LSC will cover approximately 39,000 Sequoia and 247,000 Tundra vehicles equipped with a 5.7 liter gasoline or 5.7 Liter-Flex Fuel engines.
F0A_LSC_Dealer L
Service Bulletin/Repair Instructions
Dealer Letter: In certain 2012 - 2014 Model Year Toyota Tundra and Sequoia vehicles equipped with a 5.7 Liter gasoline or 5.7 Liter-Flex Fuel engines, the Engine Control Module (ECM) may set a Diagnostic Trouble Code (DTC) if debris/ice becomes lodged in the air switching valve. If this occurs, the Malfunction Indicator (Check Engine) Light could illuminate and the vehicle could enter a "Fail-Safe" Mode (also known as "Limp-Home" Mode). If this occurs the vehicle's power and speed will be reduced, which could inconvenience you and require immediate repair.
F0A_LSC_Region L
Service Bulletin/Repair Instructions
Region Letter: In certain 2012 - 2014 Model Year Toyota Tundra and Sequoia vehicles equipped with a 5.7 Liter gasoline or 5.7 Liter-Flex Fuel engines, the Engine Control Module (ECM) may set a Diagnostic Trouble Code (DTC) if debris/ice becomes lodged in the air switching valve. If this occurs, the Malfunction Indicator (Check Engine) Light could illuminate and the vehicle could enter a "Fail-Safe" Mode (also known as "Limp-Home" Mode). If this occurs the vehicle's power and speed will be reduced, which could inconvenience you and require immediate repair.
TC15-001
Service Bulletin/Repair Instructions
TOYOTA 2012-2014 TUNDRA AND SEQUOIA VEHICLES: TSB CONTAINS AN OWNER'S NOTIFICATION LETTER. SELECT DOCUMENT SEARCH BUTTON BELOW. ON CERTAIN MODELS THE ENGINE CONTROL MODULE MAY SET A DTC TROUBLE CODE IF ICE OR DEBRIS EFFECTS THE AIR SWITCHING VALVE. *LJ
T-SB-0006-14 Rev
Service Bulletin/Repair Instructions
TSB: OBSOLETE NOTICE December 22, 2014: This bulletin is now obsolete. Please see T-SB-0160-14. ©
T-SB-0160-14
Service Bulletin/Repair Instructions
TSB: Some 2014 model year applicable vehicles equipped with Entune Audio (version 010169)/ Entune Audio Plus (version 010171) / Entune Premium Audio (version 010185) may exhibit one or more of the following conditions: ? Bluetooth sometime disconnects with Android phones. ? Bluetooth disconnects with iPhone 4 when connected to USB ? Radio reboots with heavy radio load condition (e.g., dual map and POIs ON and Entune Audio music ON and multiple destinations set) (Entune Premium Audio only) ? Radio reboots after completing a navigation route by voice command system and pressing Talk Switch (Entune Premium Audio only)
T-SB-0058-13 Rev
Service Bulletin/Repair Instructions
TSB: Some 2012 ? 2015 model year Sequoia and Tundra vehicles with the 3UR-FBE engine may exhibit a MIL ?ON? condition with Diagnostic Trouble Codes (DTCs) P0171/P0174 (System too Lean Bank 1/Bank 2), P0172/P0175 (System too Rich Bank 1/Bank 2), P1604 (Startability Malfunction), and/or P1605 (Rough Idling) after attempting to start the engine. Alcohol Density Estimate values may be high even though the vehicle was fueled with regular fuel (E0/E10). The Engine Control Module/ECM (SAE term: Powertrain Control Module/PCM) logic has been modified to address this condition. Use the following Repair Procedure to reprogram the ECM (PCM). ©
T-SB-0144-14
Service Bulletin/Repair Instructions
TSB: Some 2014 - 2015 model year Sequoia and Tundra vehicles equipped with 3UR engines may exhibit a MIL "ON" condition with the following Diagnostic Trouble Codes (DTCs): ? P2440: Secondary Air Injection System Switching Valve Stuck Open Bank 1 ? P2442: Secondary Air Injection System Switching Valve Stuck Open Bank 2 This condition may be caused by debris/ice in the air switching valve assembly. The Engine Control Module/ECM (SAE term: Powertrain Control Module/PCM) logic has been changed to reduce the possibility of this condition occurring.
T-SB-0006-11 Rev
Service Bulletin/Repair Instructions
TSB: World Standard (WS) Automatic Transmission Fluid (ATF) was introduced to reduce maintenance costs and increase the mileage between scheduled maintenance checks. Here are some important tips when working with ATF-WS in Toyota vehicles requiring it's use.
T-SB-0014-11 Rev
Service Bulletin/Repair Instructions
TSB: The purpose of this service bulletin is to provide information regarding the installation of the correct torque converter bolts during automatic transmission/transaxle assembly replacement. Incorrect torque converter bolts or missing washers can cause damage to the torque converter assembly.
T-SB-0049-11 Rev
Service Bulletin/Repair Instructions
TSB: The purpose of this bulletin is to provide information regarding transmission and/or park neutral position switch installation. If the manual shift lever is rotated prior to installing the park neutral position switch, the detent spring may become detached from the manual shift lever.
T-TT-0309-14
Service Bulletin/Repair Instructions
Tech Tip: Some customers may experience Bluetooth disconnections or loss of SMS Text Message Functionality on the navigation/audio system with Android phones running OS 4.4 or later. Condition tends to occur to customers who have many previous text messages on their phones.
T-TT-0307-14
Service Bulletin/Repair Instructions
Tech Tip: Customer complains of carious Bluetooth connectivity concerns after upgrading to iOS 8.0 and later. Conditions typically experienced include inability to pair the iPhone to the system, poor sound quality during phone calls placed through the audio/navigation system, and the inability to place a hands free phone call using the audio/navigation system.
T-SB-0137-14
Service Bulletin/Repair Instructions
TSB: Some 2014 model year Tundra vehicles may exhibit a condition where the seat heaters are inoperative in extreme cold temperatures (-4°F [-20°C] or lower). An updated A/C Amplifier is available to address this condition.
T-SB-0134-14
Service Bulletin/Repair Instructions
TSB: The purpose of this bulletin is to provide precautions to follow when installing an automatic transmission/transaxle assembly to avoid MIL "ON" shifting issues and/or transmission damage. Use the information in this bulletin when installing an automatic transmission/transaxle assembly.
T-SB-0200-08 Rev
Service Bulletin/Repair Instructions
TSB: The purpose of this bulletin is to assist in the identification and location of serial numbers on 2006 - 2014 model year automatic transmissions.
9-11-14
Service Bulletin/Repair Instructions
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
T-TT-0234-13
Service Bulletin/Repair Instructions
Tech Tip: Since MY 2011, several different update or upgrade USB SSTs have been issued for Toyota audio and navigation systems.
T-SB-0062-14
Service Bulletin/Repair Instructions
TSB: Some 2014 model year CrewMax and Double Cab Tundra vehicles may exhibit a condition where the driver's left rear seat track cover is being caught by the seat side shield, causing the seat track cover to bend backwards when the seat is in the rearmost position. Follow the procedures in this bulletin to address this condition.
JTR#20140414TC
Service Bulletin/Repair Instructions
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
TundraTacoma_Qua
Service Bulletin/Repair Instructions
Dealer Letter: 1. Intermediate Shaft Installation Confirmation Instructions 2. Reporting Results back to TMS 3. Claim filing instructions
T-TT-0246-13 Rev
Service Bulletin/Repair Instructions
Tech Tip: Tips for writing a DPR (Dealer Product Report) on manufacturing issues for windows and windshields.
T-TT-0295-14
Service Bulletin/Repair Instructions
Tech Tip: 2014 MY vehicles equipped with Entune Plus and Entune Premium Audio System* may exhibit a condition which HD traffic is not being displayed. *NOTE: Camry and Camry HV are 2014.5 MY.
T-TT-0010-10 Rev
Service Bulletin/Repair Instructions
Tech Tip: Low battery voltage can contribute to a MIL "ON" condition for P0335 (Crankshaft Position Sensor Circuit) and/or P0340 (Camshaft Position Sensor Circuit) due to inconsistent rotational speed of the engine's crankshaft.
T-SB-0020-14
Service Bulletin/Repair Instructions
TSB: Some 2014 model year vehicles equipped with Entune? Premium Audio System may exhibit one or more of the following conditions: Some POIs are shown multiple times, Some POIs cannot be searched, some road names and POIs in voice guidance do not match actual names, some city names cannot be recognized by Voice Command System, navigation routes to wrong location when destination is input by address. A new Map Micro SD Card is now available to address these conditions.
T-TT-0287-14
Service Bulletin/Repair Instructions
Park Assist False Activation on Vehicle with steel bumpers.
T-SB-0017-14
Service Bulletin/Repair Instructions
The purpose of this bulletin is to provide a procedure to adjust tire pressure correctly when outside temperature is significantly colder or warmer than shop temperature. Seasonal temperature change can dramatically alter tire pressure, which can cause the low tire pressure warning light to illuminate.
T-TT-0268-13
Service Bulletin/Repair Instructions
Customer complains of Bluetooth connectivity concerns such as: Difficulty to pair phone, Intermittent Bluetooth failure to connect to the vehicle when first turning on the vehicle. These concerns can be caused by changes made on the customer's phone. Make sure to inquire with the customer if the connectivity concerns occurred after receiving an operating system update on their phone or they have restored their phone data/settings recently.
T-TT-0262-13
Service Bulletin/Repair Instructions
Starting with the 2010 Model Year, Toyota began a gradual transition to the use of synthetic 0w-20 viscosity engine oil. There are multiple benefits of this oil. Due to the improved performance and durability of 0w-20 synthetic oil, Toyota has extended the oil change intervals to 10,000 miles for most vehicle that require this oil.
T-SB-0187-12 Rev
Service Bulletin/Repair Instructions
Toyota vehicles are equipped with either conventional or run-flat tires. Sometimes punctures may occur as a result of contact with road debris or other hazards. If a puncture occurs, it may be possible to repair the tire and return it to service. With a conventional tire it is not possible to drive for an extended amount of time with the tire at low pressures as damage to the tire may occur. With run-flat tires, due to reinforced sidewalls, it is possible to drive for up to 100 miles (160 km) at speeds less than 55 mph (90 km/h) with little or no damage to the tire.
T-SB-0006-14
Service Bulletin/Repair Instructions
Some 2014 model year applicable vehicles equipped with Entune? (version 010169) / Entune? Plus (version 010171) / Entune? Premium (version 010185) Audio may exhibit one or more of the following conditions
T-SB-0185-13
Service Bulletin/Repair Instructions
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
T-TT-0274-13
Service Bulletin/Repair Instructions
Some 14MY Toyota models equipped with a new multimedia system have 3 settings for voice recognition prompts depending on how much voice guidance the customer prefers to have.
T-SB-0122-11 Rev
Service Bulletin/Repair Instructions
Beginning in 1998, Toyota introduced side airbags as optional equipment. Toyota does NOT recommend replacement of original seat covers with non-Toyota leather or other seat cover materials on vehicles due to the following: Seat covers NOT recommended by Toyota may affect side airbag performance, in general or in part, during an accident. Modifications that negatively affect side airbag performance can result in severe occupant injuries. Seat covers are an integral part of this safety system. Replacing fabric seat covers with non-Toyota leather or other seat cover materials may compromise the effectiveness of this safety system. The design of the seat is complex, integrating safety and strength with comfort and luxury. Toyota strongly discourages modifying original equipment seats that have optional side airbags. Additionally, Toyota strongly advises against the installation or use of aftermarket seat covers, which could impair the performance of the side airbags in the event of an accident.
T-TT-0267-13
Service Bulletin/Repair Instructions
Some vehicles equipped with Display Audio may exhibit a condition where the touch screen is inoperative.
T-TT-0269-13
Service Bulletin/Repair Instructions
The appearance of spots in tempered glass (when viewed at certain angles) is the result of the heat treating and quick quenching process during manufacturing.
T-TT-0263-13
Service Bulletin/Repair Instructions
Some customers may experience difficulties using the voice command system. The new multimedia systems have new features to improve the voice command experience.
T-TT-0051-10
Service Bulletin/Repair Instructions
If a customer states there is an unpleasant odor in the vehicle from the HVAC system, there are various factors that may be involved.
T-TT-0260-13
Service Bulletin/Repair Instructions
Customer?s experiencing this condition can use a 3rd party podcast application on their iPhone (such as Pocket Casts or Instances) instead of the native Apple Podcast application.
T-SB-0071-11 Rev
Service Bulletin/Repair Instructions
The purpose of this service bulletin is to provide precautions to follow when installing an automatic transmission/transaxle assembly to avoid MIL ?ON,? shifting issues, and/or transmission damage. Use the information in this bulletin when installing an automatic transmission/transaxle assembly
T-TT-0257-13
Service Bulletin/Repair Instructions
iTunes Radio is a new feature for iPhone 4, 4S, 5, 5S, and 5C running iOS 7 or later. This feature does work with the in-vehicle audio system either via Bluetooth or by USB cable. Details on how to access this feature are described below.
T-TT-0256-13
Service Bulletin/Repair Instructions
Customers using iPhone 4, 4S, 5, 5S, or 5C running iOS 7.0 or later now have the ability to make Facetime Audio calls (no video). When a customer is paired by Bluetooth Hands Free and they make a Facetime Audio call the vehicle radio will treat it as a typical Bluetooth phone call. Because Facetime works differently than a typical phone call, the in-vehicle experience may not meet the customer?s expectations.
T-TT-0256-13A
Service Bulletin/Repair Instructions
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
T-TT-0051-10 Rev
Service Bulletin/Repair Instructions
If a customer states there is an unpleasant odor in the vehicle from the HVAC system, there are various factors that may be involved.
T-TT-0250-13
Service Bulletin/Repair Instructions
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
T-TT-0250-13 Rev
Service Bulletin/Repair Instructions
To receive satellite radio functions after the initial trial period has expired, the customer must enter into a contract with XM Satellite Radio Inc. After entering into a contract, registration of an 8-digit XM Radio ID is required. This 8-digit XM Radio ID is found by turning to channel ?0? of the satellite radio.
T-SB-0142-13
Service Bulletin/Repair Instructions
Some 2004 ? 2014 model year Toyota vehicles may exhibit odors naturally occurring from the HVAC system and/or related environmental factors. Although there is no way to eliminate these odors, follow the General Procedure in this bulletin to minimize the odors experienced.
T-SB-0141-13
Service Bulletin/Repair Instructions
A new Special Service Tool (SST 09709-00002) has been introduced to aid in the inspection procedure for certain vehicles equipped with a floor pedal-type parking brake system. This bulletin references the correct method for installing the Brake Pedal Force Gauge. Refer to the appropriate Repair Manual for parking brake pedal travel inspection and adjustment specification.
T-SB-0023-13 Rev
Service Bulletin/Repair Instructions
2014 model year vehicles are equipped with driver?s side floor mat retaining clips to secure the floor mat in the correct position. In addition, some models may utilize retaining clips for passenger side and rear seat floor mats as well. Follow the appropriate installation procedure to attach the driver?s side, and if applicable, the passenger?s side and rear seat floor mats to the vehicle carpet using the floor mat retaining clips during Pre-Delivery Service (PDS).
T-TT-0249-13
Service Bulletin/Repair Instructions
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
T-SB-0095-13 Rev
Service Bulletin/Repair Instructions
2014 Pre-Delivery Service Check Sheet
T-SB-0099-13
Service Bulletin/Repair Instructions
A download and installation process is required to activate the Entune? suite of Apps & Data Services before they are used for the first time on new vehicles. The download and installation process may also need to be performed under other circumstances such as following a head unit replacement or after the customer?s personal settings are erased. The download and installation process requires between 3 and 15 minutes to complete, depending on the file size, cellular connection speed, and other factors. Following the download and installation process, small Entune? App updates may also occur via an over-the-air update system. Follow the procedure below to perform the download and installation process.
T-TT-0005-10
Service Bulletin/Repair Instructions
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
SCS-2014 T
Service Bulletin/Repair Instructions
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
T-SB-0095-13
Service Bulletin/Repair Instructions
2014 Pre-Delivery Service Check Sheet
T-SB-0096-13
Service Bulletin/Repair Instructions
Customer retention and proper maintenance of vehicles has been a major focus for Toyota. To help remind customers that regular oil changes are essential to the proper maintenance of their vehicle, dealers are required to begin installing a first oil change reminder sticker prior to delivery. By doing this, customers will be reminded to return to your dealership for their first oil change. Your current oil change reminder sticker may be used. (See PDS Check Sheet item 8 of ?Final Inspection & Cleaning.?) A new PDS Check Sheet has been developed for the 2014 model year Tundra. Some check points have been added, expanded, or clarified. Bulletins are available for items in bold type.
T-TT-0246-13
Service Bulletin/Repair Instructions
Tips for writing a DPR (Dealer Product Report) on manufacturing issues for windows and windshields.
T-SB-0083-13
Service Bulletin/Repair Instructions
The procedure in this bulletin is a general guideline on how to properly diagnose the air conditioning system after a component failure. Refer to the applicable Repair Manual for vehicle specific repair procedures and parts.
T-TT-0124-11
Service Bulletin/Repair Instructions
Please refer to the following recommendations for the best practices for vehicle tire rotations.
T-SB-0058-13
Service Bulletin/Repair Instructions
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
T-SB-0391-08 Rev
Service Bulletin/Repair Instructions
This bulletin contains general vehicle pulling diagnosis and repair procedures along with specific information to help correct pulling complaints.
T-SB-0021-13
Service Bulletin/Repair Instructions
Long-term or off-site storage requires special care to keep vehicles factory fresh and ready for delivery. The following guidelines should be performed to minimize vehicle component/part degradation due to extended vehicle storage conditions. Long-term storage can affect a vehicle?s systems and components. Any problems that are found should be corrected immediately.
T-SB-0022-13
Service Bulletin/Repair Instructions
During the manufacturing process tires are mounted on the vehicle as matched sets to help reduce conditions such as pulling or drifting. If the wheels are replaced or refinished before vehicle delivery, it is important that the tires remain on the vehicle in the same location and in the same direction of rotation. Please refer to the following procedure to ensure that the original tires stay in the same location on the vehicle.
T-SB-0023-13
Service Bulletin/Repair Instructions
2014 model year vehicles are equipped with driver?s side floor mat retaining clips to secure the floor mat in the correct position. In addition, some models may utilize retaining clips for passenger side and rear seat floor mats as well. Follow the appropriate installation procedure to attach the driver?s side, and if applicable, the passenger?s side and rear seat floor mats to the vehicle carpet using the floor mat retaining clips during Pre-Delivery Service (PDS).
T-SB-0025-13
Service Bulletin/Repair Instructions
The radio antenna pole on some models is designed with a hex-cut base and requires installation using a wrench. When performing PDS or installing the antenna pole for any other reason, inspect the antenna base for a hex-cut to determine if the following procedure is required.
SST Requirements
Service Bulletin/Repair Instructions
SSTs are key elements to provide your customers with swift and accurate repairs resulting in superior customer satisfaction.
T-PG007-01
Service Bulletin/Repair Instructions
Replacement vin plates.
T-PG002-91
Service Bulletin/Repair Instructions
Product general information.