Vehicle report
Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
SB2509
On the above-mentioned vehicles, it is possible that the installation of the FMCSA decal has been omitted. Verification is necessary in order that the decal is present in accordance with the requirements of FMCSA.
SB2485
The purpose of this service bulletin is to inform you that VDL Van Hool has gradually switched over to other components for the front axle steering system. This switch-over has been cut into production as from units 83097 (CX35) and 84560 (CX45). Previous references may be used further, but for future orders only the new components will be supplied.
SB2501
The control arms of the front and trailing axles are equipped with a flexible ball-joint at the chassis side. Van Hool has several suppliers for the repair kit of this flexible ball-joint. All of the repair kits contain a flexible ball-joint, a spacer and a snap ring. Due to not equal thickness of the spacer in the different kits, it is important to install all three the kit parts when replacing a flexible ball-joint. Do not mix parts of different repair kits!
SB2497
Mobile column lifts raise the vehicle under the wheels. This service bulletin is a reminder about the usage of mobile column lifts when lifting a complete vehicle.
SB2262B
TO CHECK EMERGENCY SIDE WINDOW OPERATION To ensure trouble-free operation, the emergency side windows must be checked on a regular basis. This will allow you to confirm the proper operation of the emergency exit handle and unlatching mechanism, as well as the proper installation and function of the window seals
SB2494
INTRODUCTION The purpose of this service bulletin is to inform you about the removal and installation of Raufoss line fittings
SB2468
Van Hool recently changed-over in production to a “longer” articulation shaft (VH11717611) to fasten the wheel-suspension arms to the steering knuckle carrier/hub carrier. Field experience has shown that this change-over has a positive impact on the lifespan of the rubber bushings. The “longer” articulation shaft may be used with the M18 as well as with the M20 fastening system (refer to figures 2 and 3).
SB2372B
This service bulletin provides you with information about the location of emergency side window decals so that the vehicle meets the National Highway Traffic Safety Administration’s (NHTSA) Federal Motor Vehicle Safety Standards (FMVSS) in the U.S and the Canadian Motor Vehicle Safety Standards (CMVSS) in Canada about this subject.
SB2372a
This service bulletin provides you with information about the location of emergency side window decals so that the vehicle meets the National Highway Traffic Safety Administration’s (NHTSA) Federal Motor Vehicle Safety Standards (FMVSS) in the U.S and the Canadian Motor Vehicle Safety Standards (CMVSS) in Canada about this subject.
SB1564
an Hool feels very strongly about quality and constantly focuses on product improvement. This is why we would like to ask you to provide us with the correct information as quickly as possible when filing a warranty request. A fully documented diagnostic is key in this process. The more precise and complete the supplied information is, the quicker we can finalize your request, with financial compensation when applicable. For this reason, follow the procedure below as closely as possible
SB2372
This service bulletin provides you with information about the location of emergency side window decals so that the vehicle meets the National Highway Traffic Safety Administrationâs (NHTSA) Federal Motor Vehicle Safety Standards (FMVSS) in the U.S and the Canadian Motor Vehicle Safety Standards (CMVSS) in Canada about this subject.
SB2393
Van Hool regularly receives questions regarding the bolts securing the wheel suspension arms of the front axle and tag axles to the chassis. The purpose of this service information bulletin is to inform and is partly a reminder of what already is mentioned in the maintenance manual.
SB2255
Service Information: In its production process, Bock, manufacturer of refrigerant compressors, has switched to a new type of motor protection switch for the electric motor of the refrigerant compressor. As the MP10 motor protection switch (VH11472802) is no longer made available as a spare part, as of now you will receive the new INT69G motor protection switch (VH11691810) when ordering. The MP10 and the INT69G are interchangeable, but fastening and electric connection are different.
SB1709
Product Improvement: ALL VEHICLES WITH LIGHT-ALLOY WHEELS - Introduction of wheel-end monitoring system (WEM). Van Hool has released a wheel-end monitoring system (WEM) which can be installed on all vehicles equipped with light-alloy wheels. The WEM is installed at the outboard side of the wheel and monitors vibrations produced by the wheel bearing. It warns in case of bearing raceway spalling by flashing a red LED on the unit. The WEM is delivered with a magnet which is used to change from "transport" to "standstill" mode.
SB1790
Product Improvement: To retrofit with Adaptive Cruise Control (ACC) and Collision Mitigation System (CMS) Van Hool has released ACC in combination with CMS as an option for vehicles listed in this bulletin which gives step-by-step instructions how to retrofit vehicles with these systems.
Complaint counts are reports filed with NHTSA, not failure rates. A common model collects more of them than a rare one that breaks more often.