TSB V-257-001 082026
Service Bulletin/Repair Instructions
TSB - Engine, crankcase ventilation, oil leakage.
Vehicle report
Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
TSB V-257-001 082026
TSB - Engine, crankcase ventilation, oil leakage.
TSB V-861-001 082026
TSB - Under Hood Contamination Prevention.
CBR 2599-1 082026
CBR - Aggressive Trailer Braking Troubleshooting Guide.
CBR 2598-2 082026
CBR - Injector Widget to Assist in Proper Diagnostic / Injector Repair caused by offset learning max and misfire.
CBR 2429-5 082026
CBR - Flexible Switch Panel Replacement and Calibration Procedures.
CBR 2596-1 082026
CBR - ECM Failure - No Crank/Engine Start Condition.
S4532 082026
CBR - Turbo Compound Double Idler Gear Replacement.
TSB V-590-001 072026
TSB - Wheel Speed Sensor Fitting and Cable Clamping.
CBR 2585-3 072026
CBR - The purpose of this CBR is to provide support for fault codes C106718 and/or C106818.
CBR 2545-3 072026
CBR - The purpose of this CBR is to provide guidance on fault code U114688.
TSB V-371-005 072026
TSB - Jumper Harness Repair.
CBR-2592-1 202606
The purpose of this CBR is to provide steps on how to correct a customer complaint of DTC P107B86 accompanied With intermittent loss of throttle.
CBR-2590-2 202606
The purpose of this CBR is to provide steps on how to correct a customer complaint of instrument cluster going dark (blackout) situation.
CBR-2591-1 202606
The purpose of this CBR it to provide release notes for the recent Engine ECU software.
CBR-2494-19 202606
The VN(4)'s electrical architecture relies on multiple ECUs, each handling specific functions. To ensure seamless operation and peak system performance, it is essential that all ECUs run the same software version (Software Baseline). This is accomplished by installing a complete software baseline, which is delivered via service pack.
CBR-2568-5 202606
Contact Workshop; Communication Lost With Ultracapacitor Message With Associated CCIOM DTC U100687 And A Startability Issue.
CBR-2587-2 202606
The purpose of this cbr is to provide steps on how to protect the alternator power cable connection from corrosion.
CBR-2586-1 202606
The purpose of this CBR is to address issues of exhaust stack rotation on version 4 products.
CBR-2465-7 202606
The purpose of this CBR is to help diagnosis issues with the Proactive Engine Restart system and Hood Open popup message.
CBR-2588-2 202606
The purpose of this CBR is to provide aid in VMCU fault B1524-49 along with a Rain sensor which will not calibrate.
CBR -2465 202605
The purpose of this CBR is to help diagnosis issues with the Proactive Engine Restart system and Hood Open popup message.
RD26-2 202605
If you have received this document, it is because one or more of the following Faults has been active for at least 5 minutes and can potentially prevent the Supplemental Restraint System/Airbag Inflation System (SRS) from functioning properly in the event of a collision. Tech Tool will need to be used for more detailed diagnostics.
CBR- 2587 202605
The purpose of this cbr is to provide steps on how to protect the alternator power cable connection from corrosion.
CBR-2494 202605
The purpose of this CBR is address when you should update to 6.0 service pack.
CBR-2583 202605
The purpose of this CBR is to assist in diagnosing Tire Pressure Monitoring System (TPMS) DTCs U101A /U101B as well as instructions to replace the TPMS Range Extends and Wireless Sensor Gateway if it is determined it is required.
CBR -2585 202605
The purpose of this CBR is to provide support for fault codes C106718 and/or C106818.
CBR-2584-202605
When calibrating ECS, the PTT instructions may be lacking needed information.
CBR-2435 202605
This CBR solution provides guidelines for ensuring the correct position of battery sensor modules and battery sensor harnesses on the Volvo VN(4) chassis, as well as the Battery Sensor Diagnostic, Calibration, and Configuration Procedure.
CBR-2456 202605
This CBR solution provides guidance on updating the infotainment system when customer is missing applications and/or having issues with navigation or Apple/Android CarPlay.
CBR 2441-8 202604
CBR - Key Fob Calibration and/or Replacement.
CBR 2568-3 202604
CBR - Communication Lost With Ultracapacitor Message With Associated CCIOM DTC U100687 and a Startability Issue.
RD26-1 202604
RD - Over the Air Transmission Oil Level Sensor.
CBR 2574 202604
CBR - Manual TPMS wheel sensor calibration.
CBR 2562-15 202604
CBR - Electric Pneumatic Module (EPM) Fault Code C10C256
CBR 2569-3 202604
CBR - Brake Pad Wear Indicator DTC C107E68.
CBR 2540-7 202604
CBR - Upper Bunk Restraint System – Plastic Gable Retention Field Fix
TSB V-561-002 202604
TSB - Compressor Discharge Line Routing.
S4770 032026
SC - Install Load Lock Clamp (Volvo).
CBR 2570-1 032026
CBR - EBS - Electro-Pneumatic Module - Signal Compare Failure DTC C109562 - VN (4).
CBR 2172-7 032026
CBR - No Start Condition After Over the Air Programing - VECU5 No Start "Safe State"
CBR 2564-1 032026
CBR - Check Radar Pop-up Message - VN (4).
TSB V-375-001 032026
TSB - Reversing Camera Harness, Repair.
CBR 2565-1 032026
CBR - Trailer, 12Volt Right/Left Direction Indicator Circuit Warning VN (4).
CBR 2246-5 032026
CBR - Z Spring Bracket Wear. Volvo Chassis
CBR 2514 022026
CBR - This procedure provides a temporary corrective action for the “Lost Communication to Alternator” message and Vehicle Master Control Unit (VMCU) DTC C103508 caused by a software issue.
CBR 2361 022026
CBR - Observing debris within the cooling system is possible, with this debris potentially being dark and resembling sand.
FI 4794 022026
FI - Volvo Trucks has identified faulty load lock clamps.
FI4756 022026
Fleet Improvement - Volvo Trucks has identified faulty load lock clamps.
S4343 022026
SC - Volvo Trucks has determined that a select group of trucks were built with an AHI Module fuel pressure sensor which does not meet our specifications.
CBR 2522-5 202601
CBR - Frequent Parked Regeneration Requests - VN (4).
CBR 2443-4 202601
CBR - Trailer Tandem Adjustment Procedure - VN (4).
CBR 2494-11 202601
CBR - The purpose of this CBR is outline the interim software solution for VN4. Note that this document is subject to updates and currently covers Service Pack updates to B1_T2_5.1.
CBR 2399-9 202601
CBR - Daycab Cab Roof Antenna Misalignment Causing Water Intrusion.
CBR 2548-1 202601
CBR - Shock Interference With “Z” Springs.
CBR 2540-5 202601
CBR - Upper Bunk Restraint System – Plastic Gable Retention Field Fix.
CBR 2408-16 202601
CBR - Air Production Modulator (APM) DTC C10129B - High/Excessive Flow - VN (4).
CBR 2435-16 202601
CBR - Volvo Chassis - Battery Sensor Diagnostic and Calibration Procedure - VN (4).
CBR 2545-1 202601
CBR - U114688 VMCU Communication Fault - VN (4).
CBR 2516-6 202601
CBR - CMS Black Screen Troubleshooting - VN(4).
FI S4703 202601
FI - Elemental Chassis Fairing Replacement.
SC S4743 202601
SC - MCO/VECI Label Reprint.
CBR 2540-1 202512
CBR - Upper Bunk Restraint System – Plastic Gable Retention Field Fix.
CBR 2542-2 202512
CBR - Interim Immobilizer Parameter Configuration.
CBR 2526-5 202512
CBR - Parking Heater Inoperative.
CBR 2535-1 202512
CBR - Regeneration Not Possible
CBR 2494-10 202512
CBR - The purpose of this CBR is outline the interim software solution for VN4.
CBR 2361-16 202512
CBR - 3 Liter Engines ONLY - Engine Coolant Pump Housing Leak; Coolant Found Around The Oil Cooler Duct Cover Or In Between The Coolant Pump Housing And Oil Cooler Housing
S4674 202512
SC - Cab Leveling Bar Loose
CBR 2532-1 202511
CBR - Automatic High Beam - VN (4).
S4591 202511
CBR - VN(4) Parking Heater Plumbing.
CBR 2494-7 202511
CBR - The purpose of this CBR is outline the interim software solution for VN4.
CBR 2016-18 202511
CBR - Frame or Cab Lean
CBR 2529-1 202511
CBR - Volvo Chassis - Steering Wheel Switch Harness Routing And Clipping - VN (4).
CBR 2526-4 202511
CBR - Parking Heater Inoperative - VN (4).
CBR 2514--2 202511
CBR - Lost Communication to Alternator Message - DTC C103508.
CBR 2518-2 202511
CBR - Load Lock Clamp Breaking - VN (4).
CBR 2525-2 202511
CBR - Exhaust Leak or Noise – Turbo Compound (TC) Bolt Inspection and Repair - VN (4).
CBR 2527-1 202511
CBR - Center Chassis Input Output Module(CCIOM) Fault Code U3000-94 - VN (4).
CBR 2408-15 202511
CBR - Air Production Modulator (APM) DTCC10129B - High/Excessive Flow - VN (4).
CBR 2467-5 202511
CBR - Service Required Message - VN (4).
CBR 2521-1 202511
CBR - Xantrex Inverter Sub-hardware Mismatch.
CBR 2520-2 102025
CBR - Exhaust Temperature Sensor Rationality Faults and MIL Illumination.
CBR 2516-3 102025
CBR - CMS Black Screen Troubleshooting.
CBR 2480-7 102025
CBR - Resolution Process for Locked Control Unit(s).
CBR 2514-1 102025
CBR - Lost Communication to Alternator Message.
CBR 2512-1 102025
CBR - Air-Valve Cover Popping Off Seat
CBR 2511-1 102025
CBR - Inverter Low/No Power Shutoff Bypass.
CBR 2492 092025
To address customer concerns regarding the unprotected ON/OFF button of the Xantrex power inverter located in the luggage compartment. The button should be safeguarded to prevent accidental activation, which can result in unintended battery drain.
CBR 2504 092025
Some vehicles may have reverse cameras not properly assigned from the factory.
CBR 2503 092025
The purpose of this CBR is to outline the steps for adjusting brake pedal free play following Foot Brake Modulator (FBM) replacement or when diagnostic code C10C3-77is present.
CBR 2500 092025
This procedure describes the standardized method for repairing failed inserts pulled out of a table surface. It applies only when the receiving hole is not significantly damaged. Acceptable conditions include surface fraying or peeling at the painted layer only, withno full-depth cracking.
CBR 2494 092025
The purpose of this CBR is outline the interim software solution for VN4. Note that this document is subject to updates and currently covers Service Pack updates to B1_T2_4.2.
CBR 2497 092025
Electronic control units on the VN(4), PR (4) and AN (4) contain information that is critical for vehicle functionality, maintaining vehicle life data, and maintaining vehicle compliance. Because of this, swapping ECUs from truck to truck even for diagnostic purposes may cause functional or compliance complications that may or may not be apparent.
CBR 2408 092025
This document provides guidance for addressing the APM DTC C10129B fault," High/Excessive Flow" This fault was introduced by a previous APM software package and requires specific containment actions.
CBR 2482 092025
Purpose of this CBR is to address Pop up message for PTO Malfunction when there is no PTO Installed.
CBR 2465 092025
This CBR pertains to two issues that may arise with the Proactive Engine Restart (Remote Engine Start System).
CBR 2172-5 082025
CBR - When an OTA (Over-The-Air) job starts to program the VECU blocks the starter relay out, if the job ends in a Critical failure, the vehicle will remain in Safe State.
CBR 2493-1 082025
CBR - Certain VN (4) vehicles may be equipped with an Engine Fan Override switch in the dashboard that is not operational. .
CBR 2487-082025
CBR - Purpose of this CBR is to address the issue with hoods cracking at the headlight.
CBR 2484-4 082025
CBR - The Purpose of this CBR is to assist with diagnostics for fault code U300049 on the Battery Power Management Unit (BPMU).
CBR 2489-1 082025
CBR - The purpose of this CBR is to address reports of water pooling on top of engine tunnel and/or the floor board of the cab.
CBR 2486-1 072025
CBR - The purpose of this CBR is to address issues where Contact Workshop : Trailer Light Malfunction" message displayed in instrument cluster.
CBR 2488 072025
CBR - A significant GPS reporting issue is affecting fleet operations, with trucks maintaining back-office communication but failing to transmit GPS location data.
CBR 2484 072025
CBR - The Purpose of this CBR is to assist with diagnostics for fault code U300049 on the Battery Power Management Unit (BPMU).
CBR 939 072025
CBR - US17AbstractVolvo Chassis equipped with Volvo Active Driver Assist may display DTC / Fault code SPN 516103 FMI 19 on Premium Tech Tool ( PTT ) or J-Pro, and code 167 in Bendix ACOM software.
CBR 2435-12 072025
CBR - This CBR solution provides guidelines for ensuring the correct position of battery sensor modules and battery sensor harnesses on the Volvo VN(4) chassis, as well as the Battery Sensor Diagnostic and Calibration Procedure.
CBR 2330 072025
CBR - Mechanical components with moving parts designed for high-temperature environments – such as the turbo wastegate used on the 13L TC engines – are susceptible to certain kinds of leakages due to their design requirements.
CBR 2396 072025
CBR - For newly delivered vehicles it may be found that the key fob will not unlock the door. The message "Pre-delivery Mode" maybe displayed on the instrument cluster.
CBR 2408 072025
CBR - This document provides guidance for addressing the Air ProductionModulator (APM) DTC C10129B fault, "High/Excessive Flow" This fault was introduced by a previous APM software package and requires specific containment actions.
CBR 2425 072025
CBR - This CBR solution outlines the analysis of temperature changes in sensors T1, T2, and T3 and provides a procedure for inspecting and addressing potential sensor issues related to AHI fuel injection.
CBR 2429-3 072025
CBR - This CBR solution outlines the procedures for diagnosing, replacing, calibrating, and programming Flexible Switch Panels and the Security and Cab Interface Module (SCIM) to resolve switch malfunction notifications and associated fault codes.
CBR 2431 072025
CBR - This CBR solution addresses crank no start and engine dying issues in some VN (4) and PR (4) models caused by an incorrect fuel line configuration and/or fuel line fitting not seated correctly.
CBR 2443 072025
CBR - The truck’s trailer detection system uses a brief pulse of compressed air through the red trailer supply line to detect a connected trailer, but this pulse can inadvertently re-lock air-actuated tandem slide systems; this procedure outlines a method to mitigate the issue while sliding the trailer tandems.
CBR 2447 072025
CBR - Electronically Controlled Suspension (ECS) calibration using Premium Tech Tool (PTT) is required to correct discrepancies between the cluster load indicator and actual scale values, ensuring proper functionality of liftable axles and preventing unintended axle behavior.
CBR 2465-2 072025
CBR - This CBR pertains to two issues that may arise with the Proactive Engine Restart (Remote Engine Start System).
CBR 2467-4 072025
CBR - This CBR solution was created toprovide guidance on resolving the “Service Required” message that may appear in the Instrument Cluster (IC) of VN (4) and PR (4) model vehicles under specific conditions.
CBR 2482 072025
CBR - Purpose of this CBR is to address Pop up message for PTO Malfunction when there is not PTO Installed.
CBR 2483 072025
CBR - This CBR solution outlines the diagnosis and resolution of a DL6 CAN bus resistance issue, where a 40-ohmreading causes ELD communication failure, corrected by disconnecting the SCIM A262.D connector.
CBR 2480 072025
CBR - The presence of locked electronic control units may prevent programming and diagnosis. This CBR solution provides a structured workflow to resolve such conditions, reduce downtime, and minimize unnecessary eService cases.
S4532 072025
SC - Volvo Trucks has determined that certain VN and VN 4 model trucks equipped with a D13 Turbo Compound (TC) engine may experience TC Double Idler Gear failure due to incorrect bearing preload.
CBR 2431-5 202506
CBR - This CBR solution addresses crank no start and engine dying issues in some VN (4)models caused by an incorrect fuel line configuration and/or fuel line fitting not seated correctly.
CBR 2435-10 202506
CBR - This CBR solution provides guidelines for ensuring the correct position of battery sensor modules and battery sensor harnesses on the Volvo VN(4) chassis, as well as the Battery Sensor Diagnostic and Calibration Procedure.
CBR 2477-1 202506
CBR - The purpose of this CBR is outline the interim software solution for VN4.
CBR 2473-1 202506
CBR - This document provides guidance for replacing compressed well nuts with spring nuts and screws to improve grille retention on affected units.
CBR 2474-1 202506
CBR - This bulletin provides guidance for identifying and addressing oil intrusion related to the Countershaft Brake (CSB) in AMT-G transmissions.
CBR 2408-10 202506
This document provides guidance for addressing the APM DTC C10129B fault, "High/Excessive Flow"
CBR 2472-2 202505
The purpose of this CBR is to provide instructions when trying to retrieve DTC and a Communication Failed Popup occurs.
CBR 2467-2 202505
This CBR solution was created to provide guidance on resolving the “Service Required” message that may appear in the Instrument Cluster (IC) of VN (4) model vehicles under specific conditions.
CBR 2468-2 202505
The purpose of this CBR is to help diagnosis an electrically faulty door latch.
CBR 2412-6 202505
This CBR solution provides guidance for addressing the U3000-05 fault code in theWireless Sensor GateWay (WSGW) following the S4312 Service Campaign.
CBR 2456-4 202505
This CBR solution provides guidance on updating the infotainment system when customer is missing applications and/or having issues with navigation or Apple/Android CarPlay.
CBR 2408-8 202505
This document provides guidance for addressing the APM DTC C10129B fault, "High/Excessive Flow" This fault was introduced by a previous APM software package and requires specific containment actions.
CBR 2016-14 202505
Volvo Chassis - Frame Or Cab Lean
CBR 2435-6 202505
This CBR solution provides guidelines for ensuring the correct position of battery sensor modules and battery sensor harnesses on the Volvo VN(4) chassis, as well as the Battery Sensor Diagnostic and Calibration Procedure.
CBR 2408-7 202504
CBR - This document provides guidance for addressing the APM DTC C10129B fault, "High/Excessive Flow" This fault was introduced by a previous APM software package and requires specific containment actions.
CBR 2463-3 202504
CBR - Determining source(s) of suspect abnormal turbocharger noise.
CBR 2465-1 202504
CBR - Key Fob activation issue.
CBR 2431-4 202504
CBR - This CBR solution addresses crank no start and engine dying issues in some VN (4)models caused by an incorrect fuel line configuration and/or fuel line fitting not seated correctly.
CBR 2435-5 202504
CBR - This CBR solution provides guidelines for ensuring the correct position of battery sensor modules and battery sensor harnesses on the Volvo VN(4) chassis, as well as the Battery Sensor Diagnostic and Calibration Procedure.
CBR 2456-3 202504
CBR - Infotainment system update.
S4460 202504
SC - Volvo Truck has identified that certain VN4 model trucks have a miscalculation in the inter-axle driveshaft length.
S4462 202504
SC - Volvo Trucks North America has developed an updated Hood Ventilation Grille that utilizes a mesh insert for VN(4) model vehicles.
S4463 202504
SC - Volvo Trucks North America has introduced enhanced Liner EATS (Exhaust Aftertreatment System) Mounting Straps for specific VN(4) and VN model vehicles.
S4466 2020504
SC - Volvo Trucks has determined that the XC201 firewall connector lock may not fully latch due to an interference with a tab on the cab hook interface bracket.
S4498 202504
SC - Volvo Trucks North America has determined that certain VN(4) model trucks may have been built without the dash-mounted Battery Saver Switch, despite being ordered with this feature.
S4499 202504
SC - Volvo Trucks has identified that certain VN(4) model trucks were assembled with the incorrect fastener in the door stop assembly.
S4507 202504
Fleet Campaign - Volvo Trucks has identified certain VN(4) models were built with the incorrect trailer cable/power lift gate brackets.
SC4405 202504
SC - Volvo Trucks has determined that certain VN model trucks have a mislabeled Electronic Fuse & Relay Center (EFRC) Cover.
CBR 2457 202503
CBR - Error 236 When Programming TGW
CBR 2456 202503
CBR - Infotainment Update For Missing Applications
CBR 2454 202503
CBR - Power Inverter Operation and Verification
CBR 2451 202503
CBR - Troubleshooting Mismatches.
CBR 2448 202503
CBR - Volvo Chassis - Bunk Lamp Switch Foam Block Replacement
CBR 2452 202503
CBR - Driver Display Popup Error "Door Is Open. Shift Transmission To Neutral." -Instrument Cluster Software Update
CBR 2447 202503
CBR - Volvo Chassis - VN (4) - Electronically Controlled Suspension (ECS) Calibration for Liftable Axles
CBR 2444 202503
CBR - Volvo Chassis - Bulkhead Electrical Passthrough Alignment Bracket Interference.
CBR 2453 202503
CBR - Integrated Parking Cooler Diagnostics
CBR - 2431 202502
CBR - This CBR solution addresses crank no start and engine dying issues in some VN(4) models caused by an incorrect fuel line configuration.
SC - S4312 202502
SC - Certain Volvo VN (4) model trucks may experience accelerated battery drain due to continuous power consumption by the Vehicle Master Control Unit (VMCU) and other modules.
CBR - 2016 202502
CBR - Troubleshooting cab lean should only begin after completing a vehicle preparation procedure to ensure all components are in place and settled.
SC - S4343 202502
SC - Volvo Trucks has determined that a select group of trucks were built with an AHI Module fuel pressure sensor which does not meet our specifications.
CBR 2408-3 202501
CBR - Volvo Chassis - All-New VNL, VN (4) - Air ProductionModulator (APM) DTC C10129B - High/Excessive Flow
CBR 2016-12 202501
CBR - Frame Or Cab Lean
CBR 2436 202501
CBR - Volvo Chassis - Battery SensorTransition and Troubleshooting Guide - ModelVN(4)
CBR 2361-12 202501
CBR - Volvo Chassis - Debris In 13L Cooling Systems Filled With Extended Life (VCS2)
CBR 2434-1 202501
CBR - Volvo Chassis - Headlight De-icer Function and Driver Display Message -Model VN(4).
S4346 202501
SC - Volvo Trucks has identified that certain VN model trucks equipped with a D13 Turbo Compound (TC) engine may be at risk of TC unit failure due to an under-torqued idler gear bracket.
S4349 202501
SC - Volvo Trucks has determined that certain VN model trucks equipped with a D13 Turbo Compound (TC) engine may experience TC unit failure due to an under-torqued idler gear bracket.
S4358 202501
SC - Volvo Trucks has identified that certain VN 4 model trucks equipped with a D13 Turbo Compound (TC) engine may be at risk of TC unit failure due to an under-torqued idler gear bracket.
S4370 202501
SC - Volvo Trucks has determined that certain VN 4 model trucks equipped with a D13 Turbo Compound (TC) engine may experience TC unit failure due to an under-torqued idler gear bracket.
S4254 202412
Certain Volvo VN (4) model trucks built with three flexible switch panels did not receive the correct parameters for the switch panel assignments. Some switches for features such as height control, axle load distribution, and auxiliary functions may not work as intended.
S4255 202412
Volvo Trucks has identified that certain VN (4) Day Cab model trucks may exhibit improper alignment of the driver-side (left-hand) antenna. This misalignment could lead to water intrusion if a gap is present between the roof panel and the antenna seal.
S4277 202412
Volvo Trucks has determined that certain VN(4) model trucks were built without a necessary Idle Reduction System Weight Exemption Label.
S4292 202412
Volvo Trucks has identified that 59 VN (4) day cab model trucks were manufactured without the back-up camera kit that includes the back-up monitoring scope expansion.
S4307 202412
Volvo Trucks has determined that 532 VN (4) model trucks may be equipped with chain-style anti-siphon fuel caps that could interfere with proper engagement of the fuel cap threads, resulting in difficulty during installation.
S4308 202412
Volvo Trucks has identified that certain VN model trucks may encounter an issue with the EECU during a shutdown event. If this occurs, the EECU could become corrupted, leading to multiple fault codes, engine derate, and, in some cases, preventing the truck from starting.
S4312 202412
Certain Volvo VN (4) model trucks may experience accelerated battery drain due to continuous power consumption by the Vehicle Master Control Unit (VMCU) and other modules. Depleted batteries can lead to starting issues and trigger erroneous warning lamps and fault codes across various truck modules.
RD24-034 202412
These repair instructions are intended to address the following faults: P0544-15, P2031-15, P242A-15 and P246E-15.
RD24-035 202412
These repair instructions are intended to address the following fault: P0298-00 (Engine Oil Over Temperature).
RD24-036 202412
These repair instructions are intended to address the following fault: P2047-13 (Reductant Injection Valve Control Bank 1Unit 1 - Circuit Open).
RD24-037 202412
These repair instructions are intended to address the following fault: P0217-00 (Engine Coolant Over Temperature).
RD24-038 202412
These repair instructions are intended to address the following fault: P0524-00 (Engine Oil Pressure Too Low).
RD24-039 202412
These repair instructions are intended to address the following faults: P2560-00 (Engine Coolant Level Low), Coolant Temp (Engine Coolant Temp is above 210 degrees Fahrenheit) and Oil Temp (Engine Oil Temp is above 240 degrees Fahrenheit).
RD24-040 202412
These repair instructions are intended to address the following faults: B1509-68 (Collision warning With Emergency Brake, Input Signal Failure), U1061-00 and U1062-00 (Lost Communication With FLR Module or FL Camera).
RD24-30 202412
These repair instructions are intended to address the following fault: P2463-00 (Particulate Filter Restriction - Soot Accumulation Bank 1).
RD24-31 202412
These repair instructions are intended to address the following faults: P008A-00 (Low Pressure Fuel System Pressure Too Low) and P0087-00 (Fuel Rail/ System Pressure- Tool Low Bank 1).
RD24-32 202412
These repair instructions are intended to address the following fault: P10CE-97 (Reductant Return: No Flow Detected).
RD24-33 202412
These repair instructions are intended to address the following fault: P204A-13 (Reductant Pressure Sensor - Circuit Open).
CBR-2412 202412
This CBR solution informs technicians that the U3000-05 System Programming Failure DTC following software updates has no permanent solution currently available.
CBR-2431 202412
This CBR solution addresses crank no start and engine dying issues in some VN(4) models caused by an incorrect fuel line configuration.
CBR-2429 202412
This CBR solution outlines the procedures for diagnosing, replacing, calibrating, and programming Flexible Switch Panels and the Security and Cab Interface Module (SCIM) to resolve switch malfunction notifications and associated fault codes.
CBR-2016 202412
Frame lean can be caused by several seemingly isolated possibilities. The two most common are suspension and frame assembly issues.
CBR-997 202411
Vehicles may present with oil leak coming from the clutch/flywheel housing and observation of burned clutch smell or clutch slipping. These symptoms can be mistaken as a crankshaft rear main seal leak, when the actual cause is the crankshaft adaptor O-ring.
CBR-2421 202411
Volvo Chassis - VN(4) Automatic Water Drain Message
CBR-2409 202411
CBR- 13L Engine - Rear Main Oil Seal Leak - Model Year 2025
CBR-2415 202411
Volvo Chassis - VN (4) - Coolant Leaks At De-Aeration Lines
CBR-2413 202411
During the Pre-Delivery Inspection (PDI), it may be necessary to access U-bolt hardware that is obstructed by the Reaction Rod hardware. This procedure provides instructions for gaining access to U-bolt hardware, as well as proper reinstallation of Reaction Rod hardware to prevent further interference.
CBR-2408 202410
CBR - Volvo Chassis - All-New VNL, VN (4) - Air Production Modulator (APM) DTC C10129B - High/Excessive Flow
CBR-2330 202410
CBR - Volvo Chassis - 13L TC Engine Turbocharger Wastegate Shaft To Housing Leak - VN (4) Chassis
CBR-2370 202410
CBR - Volvo Chassis - Secondary Display Blank, Will Not Turn On - VN (4) Chassis
CBR-2396 202410
CBR - Volvo Chassis - Pre-Delivery Mode Deactivation - VN (4) Chassis
CBR-2399 202410
CBR - Volvo Chassis - Day Cab Antenna Misaligned - VN (4)
CBR-2400 202410
CBR - Volvo Chassis - Cab & Chassis Ground Stud Locations - VN (4) Chassis
CBR-2401 202410
CBR - Volvo Chassis - Vehicle Communications with the New VN (4)
S4215 202410
SERVICE CAMPAIGN - Fuel Injector Update
CBR-2399 202409
CBR: All-New VNL - Day Cab Antenna Misaligned
CBR-2383 202406
CBR - Accelerator Pedal: Inspection/Instructions
Complaint counts are reports filed with NHTSA, not failure rates. A common model collects more of them than a rare one that breaks more often.