PB-47-900-WST
Service Bulletin/Repair Instructions
Parts Bulletin for Fluorosilicone Fuel Tank Cap Seals
Vehicle report
Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
PB-47-900-WST
Parts Bulletin for Fluorosilicone Fuel Tank Cap Seals
CXA 03_26_Surge Tank
CX Advocate for discolored coolant surge tanks (24CSA-20)
TSB-32-020-WST
Technical Service Bulletin for TufTrac M12 Bolts
CXA_10_25_Conmet Oil Pan
CX Advocate for ConMet Oil Pan Insert Additional Issues
24CSA-19Rev
Revised Customer Service Annoucement for No Trouble Found Heavy Duty Engine Product (HDEP) Oil Separator Leaks
PB33-005-WST
Parts Bulletin for Tie Rod Assembly Part Breakdown
CXA 3_25_NOx
CX Advocate for NOx conversion low faults
CXA 2_25_NOx
CX Advocate for NOx conversion low faults
CXA 1_16_NOx
CX Advocate for NOx conversion low faults
SS778-WST
Service Solution for Power Steering Reservoir Fill Cap Venting
WI24-019
Warranty Information letter for Detroit Line or Line Seal, High Pressure Fuel Injector Standard Repair Time Updates
24CSA-19
Customer Service Annoucement for Heavy-Duty Engine Product (HDEP) Oil Separator Leaks
24CSA-20
Customer Service Annoucement for Discolored Coolant Surge Tank on Heavy Duty Engine Product (HDEP)
SS1023366-Detroit
Service Solution for Detroit Successful Regen Reference for GHG17 DD Engines
CXA 8_24_Conmet Oil Pan
CX Advocate for ConMet Oil Pan Insert Additional Failures
CXA 7_24_Conmet Oil Pan
CX Advocate for ConMet Oil Pan Insert Additional Failures
CXA 7_24_NOx
CX Advocate for NOx conversion low faults. Update to CXA 6_24_NOx submission.
CXA 06_24_Clutch Bolts
CX Advocate communication for clutch bolts
CXA 06_24_NOx
CX Advocate communication for NOx conversion low faults
TSB35-023-WST
Technical Service Bulletin for New Final Drive Over Heat Diagnostic
SS734-WST
Service Solution for Thread Spring Pin Suspension Alignment & Installation
VSWP Customer Letter
Customer letter regarding variable speed water pump.
SS763-WST
Service Solution for DEF Pump Wiring for Cummins CM2450 Engine Controller
SS3144-FTL
Service Solution for DEF Pump Wiring for Cummins CM2450 Engine Controller
FL974
Revised Emissions Recall: Cummins DEF Sensor Shortage. REVISION: Some vehicles formerly in Group F have been moved to Group G and have been assigned a new part number as specified in Table 1. An SRT for 'Calibration Code Only: Update or Confirm' has been added, as shown in Table 2, to be used when a new DEF header is not required. There have been some other minor changes to the work instructions and SRT times.
ICI24-006
Important Campaign Information letter for FL974 - Revised Bulletin & Population
SBW83-030
Updated Western Star Service Bulletin for HVAC Actuator Replacement
SBW49-020
Western Star Service Bulletin for DEF Connector Reinforcement Caps
CALWS83-001REV
HVAC Actuator Wiring Harness. Revision History: Service kit part number changed from RDH RD5 17147 0 to WWS RD-3-9069-0 on 12/9/21. The wiring harness of the actuator of the fresh air recirculation door, shown in Fig. 1, on Western Star vehicles equipped with Red Dot HVAC systems should be inspected for signs of water intrusion and corrosion.
ICI21-030
SF626 Western Star Window Replacement Inspection Notification. This letter is to inform you that Field Service Campaign SF626 Western Star Window Replacement Inspection Notification campaign was released.
SF613
ConMet Front Hub to Rotor Fasteners. On certain vehicles, the front rotor nuts may not be torqued to manufacturer specification. Loose components could cause damage to the ABS tone rings, the ABS sensors, and the anchor plate mounting fasteners.
CALWS83-001
Customer Advisory Letter for HVAC Actuator Wiring Harness. The wiring harness of the actuator of the fresh air recirculation door, shown in Fig. 1, on Western Star vehicles equipped with Red Dot HVAC systems should be inspected for signs of water intrusion and corrosion.
SBW54-080
Western Star Service Bulletin for Key Fob ID Retention. Key fobs for remote keyless entry on Western Star vehicles are delivered in packages that include a unique ID for the fob. The ID is required when pairing the key fob with a vehicle.
SS701-WST2021
Service Solution for DT12 Harness Chaffing - PT Can Faults. Transmission will not shift into Gear while driving or will not start and trigger multiple PT CAN Fault Codes.
TechTalk23864
Tech Talk discussion on a belt stretch tool sent to service techs.
WI21-009
Warranty Information letter announcing that DTNA is increasing the Standard Diagnostic Times (SDTs) shown. The updated after treatment system (ATS) diesel exhaust fluid (DEF) pump times will be applied to repair orders opened on or after April 12, 2021.
WI21-008
Warranty Information Letter announcing DTNA is adjusting the Standard Repair Times (SRTs) shown. The updated times will be applied to repair orders opened on or after April 5, 2021.
WP21-007
Warranty Policy Letter for battery tags. DTNA determined that since adopting the AutoMeter BCT-460DTNA Powernet Assessment Tool (AutoMeter) as the required powernet system tester, not all battery tags have to be retained support Warranty-related claims.
D21M3
Detroit Field Service Campaign for DT12 Gear Grind During Downshift Software Update.
WP60-100
Updated Western Star Parts Technical Bulletin for Universal Design Floor Mats. This bulletin replaces the version dated February 12, 2021. Information about parts notes in the Paragon system have been added and the trimming instructions are revised. Universal floor mat designs fit multiple cab configurations and may require trimming. Trim lines displaying size options are scored into the pad side of the mat; use an existing floor mat as a guide for optimal results. The new mat should not interfere with safety-critical equipment, such as foot pedals.
20TS-07REV
Revised Technical Service Letter for Cold Weather Faults on GHG17/21 DD13 with MCM Software Version 14. Due to colder weather, there may be an increase in the frequency of faults, noted below, on GHG17/21 DD13 trucks built after June 5th 2019. This is due to a calibration issue in the current MCM software (14.1.1.5 or 14.2.1.3). New software is scheduled for release in the first quarter of 2021 that will address these faults.
21OEM-06
Starting on November 23, 2020, DiagnosticLink 8.13 (Build 4527) was made available. Current subscribers of DiagnosticLink 8.11 or 8.12 may upgrade to DiagnosticLink 8.13 at no cost. All DTNA Service shops & OEM locations are required to maintain the latest version of software on each of their stations.
ICI21-003
Superseding Letter to an Important Campaign Information Letter to announce a reimbursement available to dealers for travel to a customer's location to perform a recall or field service campaign. Potential travel reimbursement applies to DTNA truck dealers and Detroit Diesel distributors. Thomas Built Buses will be addressed separately. This letter supersedes ICI20-022R.
WI21-005
Warranty Information Letter for Body Builder/Truck Equipment Manufacturer Demonstration Program.
WI21-006
Warranty Information Letter for Detroit NOx Sensor Circuit Fault Codes - Claim Guidelines.
WI20-014R
Revised Warranty Information Letter for OWL and Warranty Manual Improvement: Sublets and Travel Time/Distance. In the spirit of continuous improvement, DTNA reviewed sublet-related policies and procedures. The goal was to improve language clarity and optimize processes. Revisions are in blue font.
TechTalk8097
Tech Talk discussion on western star PTO.
WI21-004
Warranty Information Letter for Detroit Resources: Exploded View DD Platform and DT12 Posters. Detroit's TechComm team created visual aids for the network and released exploded view posters for DD platform engines. In early 2021, Detroit added multiple DT12 posters.
TechTalk7777
Tech Talk discussion on tool push.
SBW35-018
Western Star Service Bulletin for Axle Flange Gasket Replaced with O-Ring. Daimler Trucks North America has released a new axle shaft to hub rubber O-ring (part number 11-30728-000) as a replacement for the paper gasket (part number 11-14418-000). The new O-ring will provide better sealing and is reusable. It is quicker and easier to use compared to the paper gasket, because using a paper gasket requires cleaning the hub when the axle shaft is removed.
SBW42-014
Western Star Service Bulletin for Access to Front Brake Zerk Fittings. Certain vehicles with Detroit front axles and Meritor EX-L front air disc brakes do not have access to the front brake zerk fittings for lubrication.
WP20-018R
Revised Warranty Policy Letter for Alliance/Mascot Aftermarket Warranty and Claim Filing. Revisions are in blue. With Mascot now in partnership with Detroit Reman and Alliance Parts, DTNA is pleased to announce that Mascot coverage has been added to OWL. Remanufactured Alliance/Mascot parts include transmission, differential, steering gear, and steering pump used in an on-highway vehicle applications. The Alliance/Mascot aftermarket warranty coverage period has not changed: depending on the part, coverage is for one (1) or two (2) years and current parts, labor, and reimbursement policies apply.
WP20-018
Warranty Policy Letter for Alliance/Mascot Aftermarket Warranty and Claim Filing. With Mascot now in partnership with Detroit Reman and Alliance Parts, DTNA is pleased to announce that Mascot coverage has been added to OWL. Remanufactured Alliance/Mascot parts include transmission, differential, steering gear, and steering pump used in an on-highway vehicle applications. The Alliance/Mascot aftermarket warranty coverage period has not changed: depending on the part, coverage is for one (1) or two (2) years and current parts, labor, and reimbursement policies apply.
TechTalk2209
Tech Talk discussion on TRW GEAR-STRG,THP60,1200RAD,AB,ST. Steering exhibits shutter when turning left.
SBW54-057
Western Star Service Bulletin for Powernet Troubleshooting Guide - Batteries, Path, Alternator, and Starter. When troubleshooting powernet issues, use the BCT-460DTNA PowerNet Assessment Tool. As of May 29, 2018, the AutoMeter is the only Daimler-approved tool for troubleshooting vehicle Powernet issues.
17TS-05REV2
Revised Technical Service Letter for Detroit DT12 TCM GHG17 Only; Bootloader Update. On Detroit DT12 equipped vehicles, it may be necessary to complete an additional step in the programming process when updating the TCM software.
20TS-07
Technical Service Letter for Cold Weather Faults on GHG17/21 DD13 with MCM Software Version 14. Due to colder weather, there may be an increase in the frequency of faults, noted below, on GHG17/21 DD13 trucks built after June 5th 2019. This is due to a calibration issue in the current MCM software (14.1.1.5 or 14.2.1.3). New software is scheduled for release in the first quarter of 2021 that will address these faults.
SBW54-077
Western Star Service Bulletin for Ordering Options for Aftermarket Power Distribution Modules (PDMs). For certain Western Star 4700 or 5700 vehicles, power distribution modules (PDMs) are typically ordered in the aftermarket by serial number and populated with fuses and circuit breakers. It may take up to three weeks for a serial number specific PDM to be processed, made, and shipped to a dealership. In order to reduce the down time of a vehicle, an alternative PDM may be ordered fully populated with fuses and circuit breakers and delivered the next day. A cost increase may be associated with this option.
SS1034783REV
Revised Service Solution for 20K Detroit Axle King Pin Lube Access. Western Star trucks equipped with 20k Detroit front axles and disc brakes built up to 8/17/2020 do not have sufficient room to access the king pin grease zerk.
WSTCAE180-2020
Portland Truck Plant Paint Changes
20TS-06
DDC Technical Service Letter for GHG17 DD Platform Heavy Duty Oil Pan Drain Plug Inserts. Some GHG17 DD Platform Heavy Duty oil pans may experience an issue with the oil pan drain plug insert spinning during removal or installation while completing an oil change. Leaking may also be observed at the drain plug and/or other plugs in the oil pan.
TechTalk7774
Tech Talk discussion on SS 1034711 HADLEY MIRROR
SBW54-076
Western Star Service Bulletin for Connecting the Chassis Harness Connector to the Cab Front Wall 104-Way Pass-Through Connector. This bulletin describes how the chassis harness connector functions and how to verify the four locks of the terminal stabilizer plate on the 104-way pass-through connector are in pre-stage position. The terminal stabilizer plate is the white plastic plate located inside the 104-way pass-through connector. The stabilizer plate floats up and down in the pass-through connector to protect the terminals from being damaged when the chassis harness connector is removed and connected.
18SP736
Detroit Diesel Special Publication informing about Heavy Duty Friction Style Belt Tensioner Kit. This heavy duty friction style belt tensioner kit contains the belt tensioner and two M10 bolts to correctly pin the friction style belt tensioner. The M10x80mm bolt is used to pin the engine cooling fan drive arm. The M10x50mm bolt is used to pin the engine accessory drive arm.
20TS-03REV2
Revised Technical Service Letter for DD Heavy Duty Platform Belt Tensioner Change. A newly designed, dual-arm friction shoe damping tensioner was implemented for the DD Heavy Duty Platform. The revision includes additional information on retrofit and service kits.
TechTalk4725
Tech Talk discussion about power steering fluid.
TechTalk7679
Tech Talk discussion on repair verification for codes like 'low air flow' when a trailer is not available.
20CSA-15
Customer Service Announcement for Release of DiagnosticLink 8.12 Service Pack 2. On Thursday, September 3, 2020, Service Pack (SP) 2 for DiagnosticLink 8.12 Standard and Professional will be made available to download from the Detroit Diesel server.
ICI20-026
Important Campaign Information Letter informing that revised bulletins for Detroit Diesel campaigns D20R1REV1 and D20M8REV1 have been posted on DTNAConnect.
WSTCAE177-2020
Meritor Transfer Case Updates
D20R1REV1
Revised Detroit Emissions Recall for Daimler Trucks North America LLC, on behalf of its Detroit Powertrain Division, has determined that some Model Year 2020 GHG21 DD13 engines require reprogramming of the MCM to meet certification. NOTE: Reference 20TS-04 Detroit CPC501T GHG21 Only; Bootloader Update if New Cascadia CPC501T is not at the software level shown in this table. The Corrective Procedure also has been updated.
SS1034783
Service Solution for 20K Detroit Axle King Pin Lube Access. WST trucks equipped with 20k Detroit front axles and disc brakes built up to 8/17/2020 do not have sufficient room to access the king pin grease zerk.
WSTCAE176-2020
Removable Front Tow Hook Changes
D20R1
Detroit Emissions Recall for GHG21 Detroit DD13 Model Year 2020 Software Reprogramming. Daimler Trucks North America LLC, on behalf of its Detroit Powertrain Division, has determined that some Model Year 2020 GHG21 DD13 engines require reprogramming of the MCM to meet certification.
ICI20-022R
Revised letter is to announce a reimbursement available to dealers for travel to a customer's location to perform a recall or field service campaign. Potential travel reimbursement applies to DTNA truck dealers and Detroit Diesel distributors. Thomas Built Buses will be addressed separately.
ICI20-022
Important Campaign Information letter announcing Dealer Travel for Campaign Performance. This letter is to announce a reimbursement available to dealers for travel to a customerÃÂÃÂÃÂâÃÂÃÂÃÂÃÂÃÂÃÂÃÂÃÂs location to perform a recall or field service campaign.
WI20-012
Warranty Information Letter informing that to ensure that DTNA policies and service network practices align, the Warranty Department will be revising the Warranty Manual.
WI20-014
Warranty Information Letter for OWL and Warranty Manual Improvement: Sublets and Travel Time/Distance. In the spirit of continuous improvement, DTNA reviewed sublet-related policies and procedures. The goal was to improve language clarity and optimize processes.
CALWST46-002
Customer Advisory Letter for Torque Validation of Steering Wheel Mounting Bracket Bolts. Western Star 4700 & 4900 vehicles equipped with a certain steering wheel mounting bracket bolt installation may have a low toque value setting.
SBW31-016
Western Star Bulletin for Non-Airliner Rear Suspension Crossmember Fastener Change. With the start of production on March 2, 2020, the fasteners used to assemble the non-Airliner rear suspension (bogie) crossmember have changed. The rear suspension bogie crossmember gussets to the C-channel will be assembled with 5/8âÂÂ18 fasteners. This change includes a revision to a higher friction nut that requires an increase in tightening torque. The new higher friction nut can be identified by its green color.
20CSA-10
Customer Service Announcement informing that Service Pack (SP) 1 for DiagnosticLinkÃÂÃÂÃÂÃÂÃÂÃÂÃÂî 8.12 Standard and Professional is available to download from the Detroit Diesel server.
20OEM-05
OEM and distributor announcement for DiagnosticLink 8.12 (Build 4527) was made available. All DTNA Service shops & OEM locations are required to maintain the latest version of software on each of their stations.
20TS-05
Technical Service Letter for EPA10, GHG14, GHG17 Diesel Particulate Filter (DPF) Compatibility. Note: This document supersedes 14 TS-25 and 15 TS-8. Detroit Diesel has determined that some, Diesel Particulate Filters (DPFs) are compatible in pairs and or can be mixed together within EPA10 and GHG14 Systems. For 1-BOX and Two-Box Configuration Aftertreatment Systems (ATS), this is only possible when the filters are used in accordance with Tables 1 and 2 shown below. All other DPFs, NOT mentioned below, are NOT compatible.
20CSA-09
Customer Service Announcement for DiagnosticLink Software Update Reminder. Due to various software changes and fixes, vehicles will require DiagnosticLink 8.12 to perform functional programming. Failure to use this version may cause errors, incomplete programming, and poor vehicle performance. Because of this, all DiagnosticLink 8.09 installed versions will be disabled as of Thursday, July 23, 2020.
SBW60-027
Service Bulletin for Guidelines for Cleaning and Disinfecting Cab Surfaces. The following guidelines are for cleaning and disinfecting commonly touched surfaces on the inside and outside of a vehicle. For best results, follow cleaning and disinfecting procedures fully and consistently. Ensure there is adequate ventilation when using chemicals. NOTICE: Wipe down fragile components carefully to avoid damaging the vehicle.
20TS-03REV
Revised Technical Service Letter for DD Heavy Duty Platform Belt Tensioner Change. A newly designed, dual-arm friction shoe damping tensioner was implemented for the DD Heavy Duty Platform.
20CSA-08
Customer Service Announcement for Release of DiagnosticLink 8.12. On Wednesday, June 10, 2020, DiagnosticLink 8.12 will be made available for download from the ordering system. Current subscribers of DiagnosticLink 8.xx can upgrade to DiagnosticLink 8.12 at no cost. All DTNA service shops are required to maintain the latest version of software on each of their stations.
WI20-009
Warranty Information Letter for a Warranty Service Replacement Engine Program Clarification. Detroit established the Warranty Service Replacement Engine Program to support an unrepairable catastrophic engine failure due to manufacturing defect. To improve understanding and utilization of the program, DTNA is clarifying eligibility and engine returns.
20TS-03
Technical Service Letter for DD Heavy Duty Platform Belt Tensioner Change. A newly designed, dual-arm friction shoe damping tensioner was implemented for the DD Heavy Duty Platform.
SS1034711
Service Solution for Hadley Upper Mirror Glass Vibration. The following suggestions are not guaranteed to eliminate or fix the Hadley mirror vibration concern. We have had mixed results in field-testing. In some cases, these solutions eliminate or reduce the vibration and in others, it does not seem to make a difference. DTNA continues to work on a permanent solution to this concern.
WI20-008
Warranty Information Letter for Warranty Training Online. DTNA is pleased to announce the release of new Warranty-related training videos. The videos provide Warranty content in short instructional videos that are available on demand through the AftermarkeTV Video Channel icon on the Aftermarket Resource Center (ARC) home page.
WP20-006
Warranty Policy Letter for Handling for Authorized Service Location Part Transfers. To promote 24-hour throughput and maximum efficiency, DTNA is adjusting multiple handling policies: Launching a new handling allowance for parts ordered from another Authorized Service Location because the facing Part Distribution Center (PDC) is out of stock Retiring Detroit's Customer First Program
WP20-007
Warranty Policy Letter for Chassis Progressive Damage Policy Change. Effective for repair orders opened on or after April 27, 2020, if an Authorized Service Location installed a part which later has a warrantable failure, progressive damage and labor may be covered under the Aftermarket Parts Limited Parts Warranty (Parts Warranty).
WP20-005
Warranty Policy Letter for Handling Change: Over the Counter Aftermarket Parts Replacement Program. DTNA is pleased to announce that handling will increase to 33% for Misc. Replacement Part type claims filed under the Over the Counter (OTC) Aftermarket Parts Replacement Program.
WI20-004
Warranty Information Letter for Warranty Long Block Program Change. The Detroit Reman Long Block Program has expanded. The expansion reduces complexity in ordering reman engines and promotes stocking reman engines to meet uptime commitments.
CALFTLWS000-01
Customer Advisory Letter for GWR Label Correction. Freightliner 108SD/114SD, Coronado, New Cascadia, and Business Class M2 vehicles and Western Star 4700 and 4900 vehicles equipped with a certain tire rating have the wrong Component GWR label. DTNA is requesting the current Component GWR label be replaced with the correct label.
SS1034615
Service Solution for Western Star Velvac Door Mirror Seal Curling. The rubber that is rolling back is actually a rubber tape. Originally, the mirrors did not have this tape. Velvac added the tape to address some whistling complaints from customers.
WSTCAE169-2018
Electronic Stability Control Requirement for US and Canadian Tractors
TS1033768
Training Solution for Western Star Front Brake Squeal - Burnishing Procedure. The brake burnishing procedure can be used to help reduce brake related noise or imbalance concerns which may occur in the field.
SS1033094
Service Solution SS 1033094 KUS Float Tube Fuel Level Sensor Inform...
TS1033014
Training Solutions for Fuel Leak Found at High Pressure Fuel Pump Weep Hole for Heavy Duty DD Engines. Occasionally we see trucks come in with fuel leaking from the high pressure fuel pump weep hole. This is NOT a defect in the pump and further diagnostics need to be performed to find the root cause.
SBW98003
Paint Peeling, Hood.
TSN 88-07
Western Star 4700 non removable bug screen with additional coverage to the bumper - TSN
Complaint counts are reports filed with NHTSA, not failure rates. A common model collects more of them than a rare one that breaks more often.