PB-47-900-WST
Service Bulletin/Repair Instructions
Parts Bulletin for Fluorosilicone Fuel Tank Cap Seals
Vehicle report
Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
PB-47-900-WST
Parts Bulletin for Fluorosilicone Fuel Tank Cap Seals
TSB-00-018-WST
Technical Service Bulletin for StarNet Manuals Moving to Technical Literature
CXA 1_16_CARB Truck Chec
CX Advocate for CARB tightening the Readiness Criteria applied to On-Board Diagnostic (OBD) test submissions for the Clean Truck Check.
CXA 11_21_CARB Truck Chec
CX Advocate for CARB tightening the Readiness Criteria applied to On-Board Diagnostic (OBD) test submissions for the Clean Truck Check.
WI24-019
Warranty Information letter for Detroit Line or Line Seal, High Pressure Fuel Injector Standard Repair Time Updates
CXA_10_17_CARB Truck Chec
CX Advocate for CARB tightening the Readiness Criteria applied to On-Board Diagnostic (OBD) test submissions for the Clean Truck Check.
SS1023366-Detroit
Service Solution for Detroit Successful Regen Reference for GHG17 DD Engines
ICI24-031
Important Campaign Information letter for DDC D23M3 - Campaign Reactivated and Extended. Field Service Campaign D23M3 - GHG17 DETROITTM DD16® Vibration Damper Replacement has been extended for an additional 6 months.
CXA 06_24_Clutch Bolts
CX Advocate communication for clutch bolts
SS763-WST
Service Solution for DEF Pump Wiring for Cummins CM2450 Engine Controller
SBW83-030
Updated Western Star Service Bulletin for HVAC Actuator Replacement
SBW49-020
Western Star Service Bulletin for DEF Connector Reinforcement Caps
ICI21-030
SF626 Western Star Window Replacement Inspection Notification. This letter is to inform you that Field Service Campaign SF626 Western Star Window Replacement Inspection Notification campaign was released.
SBW54-080
Western Star Service Bulletin for Key Fob ID Retention. Key fobs for remote keyless entry on Western Star vehicles are delivered in packages that include a unique ID for the fob. The ID is required when pairing the key fob with a vehicle.
WI21-009
Warranty Information letter announcing that DTNA is increasing the Standard Diagnostic Times (SDTs) shown. The updated after treatment system (ATS) diesel exhaust fluid (DEF) pump times will be applied to repair orders opened on or after April 12, 2021.
WI21-008
Warranty Information Letter announcing DTNA is adjusting the Standard Repair Times (SRTs) shown. The updated times will be applied to repair orders opened on or after April 5, 2021.
WP21-007
Warranty Policy Letter for battery tags. DTNA determined that since adopting the AutoMeter BCT-460DTNA Powernet Assessment Tool (AutoMeter) as the required powernet system tester, not all battery tags have to be retained support Warranty-related claims.
WP60-100
Updated Western Star Parts Technical Bulletin for Universal Design Floor Mats. This bulletin replaces the version dated February 12, 2021. Information about parts notes in the Paragon system have been added and the trimming instructions are revised. Universal floor mat designs fit multiple cab configurations and may require trimming. Trim lines displaying size options are scored into the pad side of the mat; use an existing floor mat as a guide for optimal results. The new mat should not interfere with safety-critical equipment, such as foot pedals.
21OEM-06
Starting on November 23, 2020, DiagnosticLink 8.13 (Build 4527) was made available. Current subscribers of DiagnosticLink 8.11 or 8.12 may upgrade to DiagnosticLink 8.13 at no cost. All DTNA Service shops & OEM locations are required to maintain the latest version of software on each of their stations.
ICI21-003
Superseding Letter to an Important Campaign Information Letter to announce a reimbursement available to dealers for travel to a customer's location to perform a recall or field service campaign. Potential travel reimbursement applies to DTNA truck dealers and Detroit Diesel distributors. Thomas Built Buses will be addressed separately. This letter supersedes ICI20-022R.
WI21-005
Warranty Information Letter for Body Builder/Truck Equipment Manufacturer Demonstration Program.
WI21-006
Warranty Information Letter for Detroit NOx Sensor Circuit Fault Codes - Claim Guidelines.
WI20-014R
Revised Warranty Information Letter for OWL and Warranty Manual Improvement: Sublets and Travel Time/Distance. In the spirit of continuous improvement, DTNA reviewed sublet-related policies and procedures. The goal was to improve language clarity and optimize processes. Revisions are in blue font.
WI21-004
Warranty Information Letter for Detroit Resources: Exploded View DD Platform and DT12 Posters. Detroit's TechComm team created visual aids for the network and released exploded view posters for DD platform engines. In early 2021, Detroit added multiple DT12 posters.
21TS-03
Technical Service Letter for GHG17 1-Box Inlet and Outlet Exhaust Clamps. There is a short supply of exhaust clamps, part number DDE A6809950502, used as inlet and outlet exhaust clamps on GHG17 heavy duty engines (DD13, DD15 and DD16) with a 1-Box aftertreatment configuration. Exhaust clamp part number TCX T130158342AC2 may be used as a substitute for DDE A6809950502, but be aware of the different torque specs between the two parts.
SBW35-018
Western Star Service Bulletin for Axle Flange Gasket Replaced with O-Ring. Daimler Trucks North America has released a new axle shaft to hub rubber O-ring (part number 11-30728-000) as a replacement for the paper gasket (part number 11-14418-000). The new O-ring will provide better sealing and is reusable. It is quicker and easier to use compared to the paper gasket, because using a paper gasket requires cleaning the hub when the axle shaft is removed.
WP20-018R
Revised Warranty Policy Letter for Alliance/Mascot Aftermarket Warranty and Claim Filing. Revisions are in blue. With Mascot now in partnership with Detroit Reman and Alliance Parts, DTNA is pleased to announce that Mascot coverage has been added to OWL. Remanufactured Alliance/Mascot parts include transmission, differential, steering gear, and steering pump used in an on-highway vehicle applications. The Alliance/Mascot aftermarket warranty coverage period has not changed: depending on the part, coverage is for one (1) or two (2) years and current parts, labor, and reimbursement policies apply.
WP20-018
Warranty Policy Letter for Alliance/Mascot Aftermarket Warranty and Claim Filing. With Mascot now in partnership with Detroit Reman and Alliance Parts, DTNA is pleased to announce that Mascot coverage has been added to OWL. Remanufactured Alliance/Mascot parts include transmission, differential, steering gear, and steering pump used in an on-highway vehicle applications. The Alliance/Mascot aftermarket warranty coverage period has not changed: depending on the part, coverage is for one (1) or two (2) years and current parts, labor, and reimbursement policies apply.
18SP744
Special Publication letter for Two-Filter Fuel System KM59 GEN1 DD15 DD16 Severe Duty High Pressure Fuel Rail Feed Lines Service Kit.
SBW54-057
Western Star Service Bulletin for Powernet Troubleshooting Guide - Batteries, Path, Alternator, and Starter. When troubleshooting powernet issues, use the BCT-460DTNA PowerNet Assessment Tool. As of May 29, 2018, the AutoMeter is the only Daimler-approved tool for troubleshooting vehicle Powernet issues.
17TS-05REV2
Revised Technical Service Letter for Detroit DT12 TCM GHG17 Only; Bootloader Update. On Detroit DT12 equipped vehicles, it may be necessary to complete an additional step in the programming process when updating the TCM software.
WSTCAE180-2020
Portland Truck Plant Paint Changes
20TS-06
DDC Technical Service Letter for GHG17 DD Platform Heavy Duty Oil Pan Drain Plug Inserts. Some GHG17 DD Platform Heavy Duty oil pans may experience an issue with the oil pan drain plug insert spinning during removal or installation while completing an oil change. Leaking may also be observed at the drain plug and/or other plugs in the oil pan.
TechTalk7774
Tech Talk discussion on SS 1034711 HADLEY MIRROR
18SP736
Detroit Diesel Special Publication informing about Heavy Duty Friction Style Belt Tensioner Kit. This heavy duty friction style belt tensioner kit contains the belt tensioner and two M10 bolts to correctly pin the friction style belt tensioner. The M10x80mm bolt is used to pin the engine cooling fan drive arm. The M10x50mm bolt is used to pin the engine accessory drive arm.
20TS-03REV2
Revised Technical Service Letter for DD Heavy Duty Platform Belt Tensioner Change. A newly designed, dual-arm friction shoe damping tensioner was implemented for the DD Heavy Duty Platform. The revision includes additional information on retrofit and service kits.
TechTalk4725
Tech Talk discussion about power steering fluid.
TechTalk7679
Tech Talk discussion on repair verification for codes like 'low air flow' when a trailer is not available.
20CSA-15
Customer Service Announcement for Release of DiagnosticLink 8.12 Service Pack 2. On Thursday, September 3, 2020, Service Pack (SP) 2 for DiagnosticLink 8.12 Standard and Professional will be made available to download from the Detroit Diesel server.
ICI20-022R
Revised letter is to announce a reimbursement available to dealers for travel to a customer's location to perform a recall or field service campaign. Potential travel reimbursement applies to DTNA truck dealers and Detroit Diesel distributors. Thomas Built Buses will be addressed separately.
ICI20-022
Important Campaign Information letter announcing Dealer Travel for Campaign Performance. This letter is to announce a reimbursement available to dealers for travel to a customerÃÂÃÂÃÂâÃÂÃÂÃÂÃÂÃÂÃÂÃÂÃÂs location to perform a recall or field service campaign.
WI20-012
Warranty Information Letter informing that to ensure that DTNA policies and service network practices align, the Warranty Department will be revising the Warranty Manual.
WI20-014
Warranty Information Letter for OWL and Warranty Manual Improvement: Sublets and Travel Time/Distance. In the spirit of continuous improvement, DTNA reviewed sublet-related policies and procedures. The goal was to improve language clarity and optimize processes.
SBW31-016
Western Star Bulletin for Non-Airliner Rear Suspension Crossmember Fastener Change. With the start of production on March 2, 2020, the fasteners used to assemble the non-Airliner rear suspension (bogie) crossmember have changed. The rear suspension bogie crossmember gussets to the C-channel will be assembled with 5/8âÂÂ18 fasteners. This change includes a revision to a higher friction nut that requires an increase in tightening torque. The new higher friction nut can be identified by its green color.
20CSA-10
Customer Service Announcement informing that Service Pack (SP) 1 for DiagnosticLinkÃÂÃÂÃÂÃÂÃÂÃÂÃÂî 8.12 Standard and Professional is available to download from the Detroit Diesel server.
20OEM-05
OEM and distributor announcement for DiagnosticLink 8.12 (Build 4527) was made available. All DTNA Service shops & OEM locations are required to maintain the latest version of software on each of their stations.
20TS-05
Technical Service Letter for EPA10, GHG14, GHG17 Diesel Particulate Filter (DPF) Compatibility. Note: This document supersedes 14 TS-25 and 15 TS-8. Detroit Diesel has determined that some, Diesel Particulate Filters (DPFs) are compatible in pairs and or can be mixed together within EPA10 and GHG14 Systems. For 1-BOX and Two-Box Configuration Aftertreatment Systems (ATS), this is only possible when the filters are used in accordance with Tables 1 and 2 shown below. All other DPFs, NOT mentioned below, are NOT compatible.
20CSA-09
Customer Service Announcement for DiagnosticLink Software Update Reminder. Due to various software changes and fixes, vehicles will require DiagnosticLink 8.12 to perform functional programming. Failure to use this version may cause errors, incomplete programming, and poor vehicle performance. Because of this, all DiagnosticLink 8.09 installed versions will be disabled as of Thursday, July 23, 2020.
SBW60-027
Service Bulletin for Guidelines for Cleaning and Disinfecting Cab Surfaces. The following guidelines are for cleaning and disinfecting commonly touched surfaces on the inside and outside of a vehicle. For best results, follow cleaning and disinfecting procedures fully and consistently. Ensure there is adequate ventilation when using chemicals. NOTICE: Wipe down fragile components carefully to avoid damaging the vehicle.
20TS-03REV
Revised Technical Service Letter for DD Heavy Duty Platform Belt Tensioner Change. A newly designed, dual-arm friction shoe damping tensioner was implemented for the DD Heavy Duty Platform.
20CSA-08
Customer Service Announcement for Release of DiagnosticLink 8.12. On Wednesday, June 10, 2020, DiagnosticLink 8.12 will be made available for download from the ordering system. Current subscribers of DiagnosticLink 8.xx can upgrade to DiagnosticLink 8.12 at no cost. All DTNA service shops are required to maintain the latest version of software on each of their stations.
20TS-03
Technical Service Letter for DD Heavy Duty Platform Belt Tensioner Change. A newly designed, dual-arm friction shoe damping tensioner was implemented for the DD Heavy Duty Platform.
SBW72-008REV
Service Bulletin for Window Regulator Retrofit. The bulletin dated December 4, 2019 has been revised to include 4800 Models. Beginning 04/01/2019 Western Star cab doors were updated to a new style regulator and window. When replacing an older style regulator or window the vehicle must be retrofitted to the new style regulator and window.
SS1034711
Service Solution for Hadley Upper Mirror Glass Vibration. The following suggestions are not guaranteed to eliminate or fix the Hadley mirror vibration concern. We have had mixed results in field-testing. In some cases, these solutions eliminate or reduce the vibration and in others, it does not seem to make a difference. DTNA continues to work on a permanent solution to this concern.
WI20-008
Warranty Information Letter for Warranty Training Online. DTNA is pleased to announce the release of new Warranty-related training videos. The videos provide Warranty content in short instructional videos that are available on demand through the AftermarkeTV Video Channel icon on the Aftermarket Resource Center (ARC) home page.
WP20-006
Warranty Policy Letter for Handling for Authorized Service Location Part Transfers. To promote 24-hour throughput and maximum efficiency, DTNA is adjusting multiple handling policies: Launching a new handling allowance for parts ordered from another Authorized Service Location because the facing Part Distribution Center (PDC) is out of stock Retiring Detroit's Customer First Program
WP20-007
Warranty Policy Letter for Chassis Progressive Damage Policy Change. Effective for repair orders opened on or after April 27, 2020, if an Authorized Service Location installed a part which later has a warrantable failure, progressive damage and labor may be covered under the Aftermarket Parts Limited Parts Warranty (Parts Warranty).
WP20-005
Warranty Policy Letter for Handling Change: Over the Counter Aftermarket Parts Replacement Program. DTNA is pleased to announce that handling will increase to 33% for Misc. Replacement Part type claims filed under the Over the Counter (OTC) Aftermarket Parts Replacement Program.
WI20-004
Warranty Information Letter for Warranty Long Block Program Change. The Detroit Reman Long Block Program has expanded. The expansion reduces complexity in ordering reman engines and promotes stocking reman engines to meet uptime commitments.
SBW54-075
Service Bulletin for Lengthening the Backup Light Harness. Though the back-up light harness is long enough to connect to the backup light switch, it may be short enough that the wire seals in the connector can be stressed. Moisture entering through the seals can cause corrosion, resulting in a bad connection and/or failure of the switch. As a result, backup lights and, if equipped, the backup alarm, may not function when the vehicle is shifted into reverse.
20CSA-04
Customer Service Announcement saying that Service Pack (SP) 3 for DiagnosticLinkî 8.11 Standard and Professional will be available for download from the Detroit Diesel server.
03.2020 Campaign
Open recall and Field service Campaigns report send out to Dealers, General Managers, Service managers and warranty managers.
WP20-002
Warranty Policy Letter explaining the Warranty Department is aligning with the frame rail repair policy, published in DTNA Workshop Manuals, which states that there are very few cases in which welding a heat-treated frame rail is allowed. Therefore, before welding anything on a frame rail, contact the applicable regional service representative for approval.
02.2020 Campaign
Open recall and Field service Campaigns report send out to Dealers, General Managers, Service managers and warranty managers
SS1034179
Service Solution on Western Star speedometers. For certain speedometers the speedometer may drop out or the odometer may reset to zero.
SBW54-061
Service Bulletin for Guidelines for Repairing or Replacing an Electrical Harness. Use the guidelines in this bulletin to determine if a damaged electrical harness should be repaired or replaced.
20CSA-01
Customer Service Announcement for a policy change regarding Detroit Service Information Bulletins (SIBs) will now have a 60-day expiration, starting on the release day of the bulletin. The intent of a SIB is to notify the service network of a major change to one or more service procedures. Do not save SIBs nor reference them for repairs, as they are uncontrolled and never updated.
SS1034615
Service Solution for Western Star Velvac Door Mirror Seal Curling. The rubber that is rolling back is actually a rubber tape. Originally, the mirrors did not have this tape. Velvac added the tape to address some whistling complaints from customers.
SBW83-020
Service Bulletin on A/C System Receiver-Drier Replacement Guidelines.
17TS-12REV
Technical Service Letter for GHG17 Heavy Duty Engine Platform 1-BOX Aftertreatment System (ATS) Wire Harness experiencing chaffing caused by vibration and dirt collecting in the harness conduit.
WI19-022
Warranty Information Letter announcing Detroit NOx Sensor Circuit Improvements for GHG17 After Treatment Systems
SBW72-008
Service Bulletin for Window Regulator Retrofit.
SS1034577
Service Solution to address WST Cab drone / vibration / tapping Under acceleration for vehicles w/Eaton Manual Trans.
SS1034579
Service Solution for prematurely failing coolers on WST Models equipped with Allison Transmissions and Rocore Transmission coolers (07-23256-001) with tow pin front X-member. Part number 07-25266-000 is a direct replacement of the failing coolers and requires no modifications or plumbing changes.
SBW00-004
Service Bulletin explaining Western Star's courtesy engineering policy.
SS1034499
Service Solution on failing RX modules in Western Star vehicles.
CAL_WS_42001
Customer Advisory Letter for WABCO HP air dryer turbo cut-off valve replacement.
SS1034531
Service Solution for WABCO HP air dryer turbo cut-off valve replacement.
17TS9
Technical Service Letter communicating that information on DD Heavy Duty Platform Belt and Belt Tensioner can be found on TechLit.
P&SSep2019
Parts and Service Committee meeting minutes
DOC-1034500
Service Solution to fix AC cooling performance due to improper HVAC function.
19TL-15
Tool Letter for ICC5 Programming Cable
SB47-015
Service Bulletin for Equiflo Fuel System Breather Tube Inspection
SBW54-073
Service Bulletin for Powernet Distribution Box Functional Changes
SF591
Field Service Campaign for Wabco HP Air Dryer Turbo Cut-off Valve
WP19-014
Warranty Policy Change for Delivery-Related Changes: Electronic Proof of Delivery and Loose Component Claim Filing
15CSA-3REV
Customer Service Announcement Letter Revision for Dealers/Distributors Accessing DDEC Backdoor Passwords
19CSA-12 BCT
PowerNet Assessment Tool Repair Procedure
19TL-10 NVH
Communication to assist the field with service vibration issues on DTNA vehicles
19CSA-13
Service Systems Development provided document to service locations on price list reflects current charges to engine horsepower ratings for HDEP and MDEG engine platforms.
19TS-GHG17 DD13
Document sent out by Service Systems Development to fix issue related to DD13 engines built between June 5 and July 22, 2019 starting with ESN 471928S0697276,have some incorrect values set which can cause the fan to lock on at all times.
19-011WP
Warranty Policy Letter to communicate Detroit Return Changes
19-012WP
Warranty Policy Letter to communicate remarketing handling cap for Detroit DT12 Transmission.
19-013WI
Warranty Information Letter to announce addition of Thomas Built Bus as a brand with an Authorized Demonstrator Program
19-010WI
Warranty Information Letter updated to communicate warranty system updates.
0308-19 PTO
Service Information Bulletin regarding PTO Dosing. This feature enables Active Regeneration of the DPFs while in PTO mode.
0419-19SPN521030
Updates to troubleshooting guides in Diagnostic Link with newest version
0607-19
Service Information Bulletin to updated the Fuel Injector Harness sections and relocated to Engine Electrical section.
0609-19
Service Information Bulletin for Symptom Diagnostics - Fluid in the Aftertreatment - Diesel Fuel Contamination.
0611-19
Service Information Bulletin was released, to add new procedures to address diagnostics near the high pressure pump
18SP727Rev
This service kit includes all necessary parts to replace the high pressure fuel rail feed lines, mounting bracket, P-clips and mounting hardware in the event one of these parts are loosened, removed or missing from the engine.
18SP728Rev
This service kit includes all necessary parts to replace the high pressure fuel rail feed lines, mounting bracket, P-clips and mounting hardware in the event one of these parts are loosened, removed or missing from the engine.
18SP729Rev
This service kit includes all necessary parts to replace the high pressure fuel rail feed lines, mounting bracket, P-clips and mounting hardware in the event one of these parts are loosened, removed or missing from the engine.
19-008WI
Warranty Information Letter sent to customers regarding new refrigerator supplier for returning parts.
19TL-9
DTNA Special Tools Group has approved the use of Haweka Axis4000 aftermarket alignment system for use on DTNA products at DTNA service locations. The Axis4000 system uses the reference points required by DTNA for precise, accurate, and repeatable measurements. Axis4000 is a sophisticated, user-friendly system that utilizes computer based camera-radio technology and references the center line of the frame for measuring and providing alignment results to DTNA specifications.
19TS-6
The modified parked regeneration strategy has been standard on GHG17 units since the start of GHG17 production and was added to EPA10 and GHG14 units with a software update. The modified regeneration utilizes an improved strategy to clean the DOC inlet face and reduce downtime due to DOC face plugging.
SPN 3563 / FMI 2
HDEP GHG17 engines are not equipped with turbo wastegates. Steps in this troubleshooting involving wastegates were removed.
sb54313
Service Bulletin provided to customers regarding installation of a new MCM 21-pin jumper harness.
19-009WI
Warranty Information Letter - Expanded guidelines for paint-related claims sent out to Freightliner, Western star, Thomas Built Bus, Export and Direct warranty customers
DOC-1034452
Training Solution created by DTNA to provide guidance to customers when searching for service information for components and systems not owned by Daimler Trucks North America (DTNA).
DOC-1034171
SS 1034171 Airliner Rear Suspension Chassis Lean Troubleshooting
WSTCAE170-2019
New Valeo A/C Compressor
FL766
Dealer Bulletin- FL766 Western Star Power Cable Studs
sbw0015
Service Bulletin Vibration and Harsh Ride Troubleshooting
wp54018 EPA10
Technical Bulletin wp54018 EPA10 Wiring Harness Ordering
ICI18-035 FL766
Important Campaign Information to Dealer on FL766 - Final Remedy Temporarily Suspended
sbw0015 Vibratio
Vibration and Harsh ride Troubleshooting
18-032-NoDefectF
Warranty Bulletin for charge back exemtions
FL766 Western St
Recall Bulletin FL766- Western Star Power Cable Studs
ICI18-031 FL766
Important Campaign Information- FL766 Interim Recall Ending ? Final Recall to Begin
18-028 Transport
Important Warranty Information to Freightliner and Western Star dealers on Transporter Photo Requirement Changes
TS1033768
Training Solution for Western Star Front Brake Squeal - Burnishing Procedure. The brake burnishing procedure can be used to help reduce brake related noise or imbalance concerns which may occur in the field.
D18M3-REV1 Heavy
Field Service Campaign D18M3-REV1 Heavy Duty Engine Platform Oil Suction Manifold
sbw0014
Operating Hours for the Customer Assistance Center
0508-18
0508-18 Aftertreatment
0504-18
0504-18 Fuel System - Fuel Injectors
0501-18
0501-18 Aftertreatment Control Module (ACM)
DOC-1033403
SS 1033403 - WST Wiper Motor not Parking Issues
DOC-1033462
SS 1033462 - WST Cab Mounted Mekra Mirror Cover Chrome Peeling
FL756
FL756 Brake Light Pressure Switches
ICI18-016 FL756
ICI18-016 FL756 ? Automotive Connector Terminal Removal Tool
MY18M4
MY18M4_Bulletin_02-MAY-2018 Field Service Campaign D18M4
aeo18M4
aeo18M4 Field Service Campaign D18M4
sbw0005
If a GVWR certification label is lost or damaged, Freightliner will supply a duplicate label. Log on to DTNAConnect.com and under "DTNAConnect Resources", select the "Tool and Services" plus sign. Select "Request for Certification Labl or OWI." Fillout the form, then select "Review."
sbw31014
With the start of production on April 2, 2018, the fasteners used to assemble Airliner rear suspension crossmembers changed. The forward-suspnsion crossmember will assembled with 5/8-18 fasteners and the rear-suspension (bogie) crossmember will be assembled with 3/4-16 fasteners.
0404-18
0404-18 GHG17 DD8 - Aftertreatment Systems - Diesel Particulate Filter End Cap
sbw4206
sbw4206 Brake Shimmy?Meritor® SteeLite X30? Brake Drum With Excessive Runout
sbw5439
sbw5439 RX Module Fault Codes
sbw5464
sbw5464 Fuel Level Sending Unit Retrofit
sbw0002
Technical Publications Ordering
SS1033094
Service Solution SS 1033094 KUS Float Tube Fuel Level Sensor Inform...
sbw49017
Magnetized Fill Neck for Six-Gallon DEF Tanks
TS1033014
Training Solutions for Fuel Leak Found at High Pressure Fuel Pump Weep Hole for Heavy Duty DD Engines. Occasionally we see trucks come in with fuel leaking from the high pressure fuel pump weep hole. This is NOT a defect in the pump and further diagnostics need to be performed to find the root cause.
sbw3215
Some vehicles may have been incorrectly shimmed at the factory, and may lean slightly to the right or left. While this does not affect the operation of the vehicle, it may be visually unpleasing to many customers.
sbw5401
sbw5401 Turn Signal and Brake Override Circuit
sbw8325
sbw8325 Side Window Defroster and Cooling Improvement Retrofit
0237-14
0237-14 Engine Brake Solenoid
33-4
33-4- Bearing Spacer Replacement, ConMet PreSet Steer Hubs
35-11
35-11 - Bearing Spacer Replacement, ConMet PreSet Drive Hubs
sbw5455
sbw5455 Virtual Technician Retrofit
sbw0001
sbw0001Validity List Western Star
sbw2019
sbw2019 Kysor Fan Clutch Rocking Runout Inspection
sbw4911
sbw4911 DEF Gauge Reading Incorrectly
sbw3109
sbw3109 Huck-Spin 2 Changeover
Complaint counts are reports filed with NHTSA, not failure rates. A common model collects more of them than a rare one that breaks more often.